drivers/net/phy/Kconfig

   1 #
   2 # PHY Layer Configuration
   3 #
   4
   5 menuconfig PHYLIB
   6         tristate "PHY Device support and infrastructure"
   7         depends on NETDEVICES
   8         help
   9           Ethernet controllers are usually attached to PHY
  10           devices.  This option provides infrastructure for
  11           managing PHY devices.
  12
  13 if PHYLIB
  14
  15 config SWPHY
  16         bool
  17
  18 config LED_TRIGGER_PHY
  19         bool "Support LED triggers for tracking link state"
  20         depends on LEDS_TRIGGERS
  21         ---help---
  22           Adds support for a set of LED trigger events per-PHY.  Link
  23           state change will trigger the events, for consumption by an
  24           LED class driver.  There are triggers for each link speed currently
  25           supported by the phy, and are of the form:
  26                <mii bus id>:<phy>:<speed>
  27
  28           Where speed is in the form:
  29                 <Speed in megabits>Mbps or <Speed in gigabits>Gbps
  30
  31 comment "MDIO bus device drivers"
  32
  33 config MDIO_BCM_IPROC
  34         tristate "Broadcom iProc MDIO bus controller"
  35         depends on ARCH_BCM_IPROC || COMPILE_TEST
  36         depends on HAS_IOMEM && OF_MDIO
  37         help
  38           This module provides a driver for the MDIO busses found in the
  39           Broadcom iProc SoC's.
  40
  41 config MDIO_BCM_UNIMAC
  42         tristate "Broadcom UniMAC MDIO bus controller"
  43         depends on HAS_IOMEM
  44         help
  45           This module provides a driver for the Broadcom UniMAC MDIO busses.
  46           This hardware can be found in the Broadcom GENET Ethernet MAC
  47           controllers as well as some Broadcom Ethernet switches such as the
  48           Starfighter 2 switches.
  49
  50 config MDIO_BITBANG
  51         tristate "Bitbanged MDIO buses"
  52         help
  53           This module implements the MDIO bus protocol in software,
  54           for use by low level drivers that export the ability to
  55           drive the relevant pins.
  56
  57           If in doubt, say N.
  58
  59 config MDIO_BUS_MUX
  60         tristate
  61         depends on OF_MDIO
  62         help
  63           This module provides a driver framework for MDIO bus
  64           multiplexers which connect one of several child MDIO busses
  65           to a parent bus.  Switching between child busses is done by
  66           device specific drivers.
  67
  68 config MDIO_BUS_MUX_BCM_IPROC
  69         tristate "Broadcom iProc based MDIO bus multiplexers"
  70         depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
  71         select MDIO_BUS_MUX
  72         default ARCH_BCM_IPROC
  73         help
  74           This module provides a driver for MDIO bus multiplexers found in
  75           iProc based Broadcom SoCs. This multiplexer connects one of several
  76           child MDIO bus to a parent bus. Buses could be internal as well as
  77           external and selection logic lies inside the same multiplexer.
  78
  79 config MDIO_BUS_MUX_GPIO
  80         tristate "GPIO controlled MDIO bus multiplexers"
  81         depends on OF_GPIO && OF_MDIO
  82         select MDIO_BUS_MUX
  83         help
  84           This module provides a driver for MDIO bus multiplexers that
  85           are controlled via GPIO lines.  The multiplexer connects one of
  86           several child MDIO busses to a parent bus.  Child bus
  87           selection is under the control of GPIO lines.
  88
  89 config MDIO_BUS_MUX_MMIOREG
  90         tristate "MMIO device-controlled MDIO bus multiplexers"
  91         depends on OF_MDIO && HAS_IOMEM
  92         select MDIO_BUS_MUX
  93         help
  94           This module provides a driver for MDIO bus multiplexers that
  95           are controlled via a simple memory-mapped device, like an FPGA.
  96           The multiplexer connects one of several child MDIO busses to a
  97           parent bus.  Child bus selection is under the control of one of
  98           the FPGA's registers.
  99
 100           Currently, only 8-bit registers are supported.
 101
 102 config MDIO_CAVIUM
 103         tristate
 104
 105 config MDIO_GPIO
 106         tristate "GPIO lib-based bitbanged MDIO buses"
 107         depends on MDIO_BITBANG && GPIOLIB
 108         ---help---
 109           Supports GPIO lib-based MDIO busses.
 110
 111           To compile this driver as a module, choose M here: the module
 112           will be called mdio-gpio.
 113
 114 config MDIO_HISI_FEMAC
 115         tristate "Hisilicon FEMAC MDIO bus controller"
 116         depends on HAS_IOMEM && OF_MDIO
 117         help
 118           This module provides a driver for the MDIO busses found in the
 119           Hisilicon SoC that have an Fast Ethernet MAC.
 120
 121 config MDIO_MOXART
 122         tristate "MOXA ART MDIO interface support"
 123         depends on ARCH_MOXART
 124         help
 125           This driver supports the MDIO interface found in the network
 126           interface units of the MOXA ART SoC
 127
 128 config MDIO_OCTEON
 129         tristate "Octeon and some ThunderX SOCs MDIO buses"
 130         depends on 64BIT
 131         depends on HAS_IOMEM
 132         select MDIO_CAVIUM
 133         help
 134           This module provides a driver for the Octeon and ThunderX MDIO
 135           buses. It is required by the Octeon and ThunderX ethernet device
 136           drivers on some systems.
 137
 138 config MDIO_SUN4I
 139         tristate "Allwinner sun4i MDIO interface support"
 140         depends on ARCH_SUNXI
 141         help
 142           This driver supports the MDIO interface found in the network
 143           interface units of the Allwinner SoC that have an EMAC (A10,
 144           A12, A10s, etc.)
 145
 146 config MDIO_THUNDER
 147         tristate "ThunderX SOCs MDIO buses"
 148         depends on 64BIT
 149         depends on PCI
 150         select MDIO_CAVIUM
 151         help
 152           This driver supports the MDIO interfaces found on Cavium
 153           ThunderX SoCs when the MDIO bus device appears as a PCI
 154           device.
 155
 156 config MDIO_XGENE
 157         tristate "APM X-Gene SoC MDIO bus controller"
 158         depends on ARCH_XGENE || COMPILE_TEST
 159         help
 160           This module provides a driver for the MDIO busses found in the
 161           APM X-Gene SoC's.
 162
 163 comment "MII PHY device drivers"
 164
 165 config AMD_PHY
 166         tristate "AMD PHYs"
 167         ---help---
 168           Currently supports the am79c874
 169
 170 config AQUANTIA_PHY
 171         tristate "Aquantia PHYs"
 172         ---help---
 173           Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405
 174
 175 config AT803X_PHY
 176         tristate "AT803X PHYs"
 177         ---help---
 178           Currently supports the AT8030 and AT8035 model
 179
 180 config BCM63XX_PHY
 181         tristate "Broadcom 63xx SOCs internal PHY"
 182         depends on BCM63XX
 183         select BCM_NET_PHYLIB
 184         ---help---
 185           Currently supports the 6348 and 6358 PHYs.
 186
 187 config BCM7XXX_PHY
 188         tristate "Broadcom 7xxx SOCs internal PHYs"
 189         select BCM_NET_PHYLIB
 190         ---help---
 191           Currently supports the BCM7366, BCM7439, BCM7445, and
 192           40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
 193
 194 config BCM87XX_PHY
 195         tristate "Broadcom BCM8706 and BCM8727 PHYs"
 196         help
 197           Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
 198
 199 config BCM_CYGNUS_PHY
 200         tristate "Broadcom Cygnus SoC internal PHY"
 201         depends on ARCH_BCM_CYGNUS || COMPILE_TEST
 202         depends on MDIO_BCM_IPROC
 203         select BCM_NET_PHYLIB
 204         ---help---
 205           This PHY driver is for the 1G internal PHYs of the Broadcom
 206           Cygnus Family SoC.
 207
 208           Currently supports internal PHY's used in the BCM11300,
 209           BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
 210           BCM58303 & BCM58305 Broadcom Cygnus SoCs.
 211
 212 config BCM_NET_PHYLIB
 213         tristate
 214
 215 config BROADCOM_PHY
 216         tristate "Broadcom PHYs"
 217         select BCM_NET_PHYLIB
 218         ---help---
 219           Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
 220           BCM5481, BCM54810 and BCM5482 PHYs.
 221
 222 config CICADA_PHY
 223         tristate "Cicada PHYs"
 224         ---help---
 225           Currently supports the cis8204
 226
 227 config DAVICOM_PHY
 228         tristate "Davicom PHYs"
 229         ---help---
 230           Currently supports dm9161e and dm9131
 231
 232 config DP83848_PHY
 233         tristate "Texas Instruments DP83848 PHY"
 234         ---help---
 235           Supports the DP83848 PHY.
 236
 237 config DP83867_PHY
 238         tristate "Texas Instruments DP83867 Gigabit PHY"
 239         ---help---
 240           Currently supports the DP83867 PHY.
 241
 242 config FIXED_PHY
 243         tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
 244         depends on PHYLIB
 245         select SWPHY
 246         ---help---
 247           Adds the platform "fixed" MDIO Bus to cover the boards that use
 248           PHYs that are not connected to the real MDIO bus.
 249
 250           Currently tested with mpc866ads and mpc8349e-mitx.
 251
 252 config ICPLUS_PHY
 253         tristate "ICPlus PHYs"
 254         ---help---
 255           Currently supports the IP175C and IP1001 PHYs.
 256
 257 config INTEL_XWAY_PHY
 258         tristate "Intel XWAY PHYs"
 259         ---help---
 260           Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
 261           These PHYs are marked as standalone chips under the names
 262           PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
 263           SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
 264
 265 config LSI_ET1011C_PHY
 266         tristate "LSI ET1011C PHY"
 267         ---help---
 268           Supports the LSI ET1011C PHY.
 269
 270 config LXT_PHY
 271         tristate "Intel LXT PHYs"
 272         ---help---
 273           Currently supports the lxt970, lxt971
 274
 275 config MARVELL_PHY
 276         tristate "Marvell PHYs"
 277         ---help---
 278           Currently has a driver for the 88E1011S
 279
 280 config MESON_GXL_PHY
 281         tristate "Amlogic Meson GXL Internal PHY"
 282         depends on ARCH_MESON || COMPILE_TEST
 283         ---help---
 284           Currently has a driver for the Amlogic Meson GXL Internal PHY
 285
 286 config MICREL_PHY
 287         tristate "Micrel PHYs"
 288         ---help---
 289           Supports the KSZ9021, VSC8201, KS8001 PHYs.
 290
 291 config MICROCHIP_PHY
 292         tristate "Microchip PHYs"
 293         help
 294           Supports the LAN88XX PHYs.
 295
 296 config MICROSEMI_PHY
 297         tristate "Microsemi PHYs"
 298         ---help---
 299           Currently supports VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
 300
 301 config NATIONAL_PHY
 302         tristate "National Semiconductor PHYs"
 303         ---help---
 304           Currently supports the DP83865 PHY.
 305
 306 config QSEMI_PHY
 307         tristate "Quality Semiconductor PHYs"
 308         ---help---
 309           Currently supports the qs6612
 310
 311 config REALTEK_PHY
 312         tristate "Realtek PHYs"
 313         ---help---
 314           Supports the Realtek 821x PHY.
 315
 316 config SMSC_PHY
 317         tristate "SMSC PHYs"
 318         ---help---
 319           Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
 320
 321 config STE10XP
 322         tristate "STMicroelectronics STe10Xp PHYs"
 323         ---help---
 324           This is the driver for the STe100p and STe101p PHYs.
 325
 326 config TERANETICS_PHY
 327         tristate "Teranetics PHYs"
 328         ---help---
 329           Currently supports the Teranetics TN2020
 330
 331 config VITESSE_PHY
 332         tristate "Vitesse PHYs"
 333         ---help---
 334           Currently supports the vsc8244
 335
 336 config XILINX_GMII2RGMII
 337        tristate "Xilinx GMII2RGMII converter driver"
 338        ---help---
 339          This driver support xilinx GMII to RGMII IP core it provides
 340          the Reduced Gigabit Media Independent Interface(RGMII) between
 341          Ethernet physical media devices and the Gigabit Ethernet controller.
 342
 343 endif # PHYLIB
 344
 345 config MICREL_KS8995MA
 346         tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
 347         depends on SPI