2 * Implement cfg80211 ("iw") support.
4 * Copyright (C) 2009 M&N Solutions GmbH, 61191 Rosbach, Germany
5 * Holger Schurig <hs4233@mail.mn-solutions.de>
9 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
11 #include <linux/hardirq.h>
12 #include <linux/sched.h>
13 #include <linux/wait.h>
14 #include <linux/slab.h>
15 #include <linux/ieee80211.h>
16 #include <net/cfg80211.h>
17 #include <asm/unaligned.h>
25 #define CHAN2G(_channel, _freq, _flags) { \
26 .band = IEEE80211_BAND_2GHZ, \
27 .center_freq = (_freq), \
28 .hw_value = (_channel), \
30 .max_antenna_gain = 0, \
34 static struct ieee80211_channel lbs_2ghz_channels
[] = {
51 #define RATETAB_ENT(_rate, _hw_value, _flags) { \
53 .hw_value = (_hw_value), \
58 /* Table 6 in section 3.2.1.1 */
59 static struct ieee80211_rate lbs_rates
[] = {
60 RATETAB_ENT(10, 0, 0),
61 RATETAB_ENT(20, 1, 0),
62 RATETAB_ENT(55, 2, 0),
63 RATETAB_ENT(110, 3, 0),
64 RATETAB_ENT(60, 9, 0),
65 RATETAB_ENT(90, 6, 0),
66 RATETAB_ENT(120, 7, 0),
67 RATETAB_ENT(180, 8, 0),
68 RATETAB_ENT(240, 9, 0),
69 RATETAB_ENT(360, 10, 0),
70 RATETAB_ENT(480, 11, 0),
71 RATETAB_ENT(540, 12, 0),
74 static struct ieee80211_supported_band lbs_band_2ghz
= {
75 .channels
= lbs_2ghz_channels
,
76 .n_channels
= ARRAY_SIZE(lbs_2ghz_channels
),
77 .bitrates
= lbs_rates
,
78 .n_bitrates
= ARRAY_SIZE(lbs_rates
),
82 static const u32 cipher_suites
[] = {
83 WLAN_CIPHER_SUITE_WEP40
,
84 WLAN_CIPHER_SUITE_WEP104
,
85 WLAN_CIPHER_SUITE_TKIP
,
86 WLAN_CIPHER_SUITE_CCMP
,
89 /* Time to stay on the channel */
90 #define LBS_DWELL_PASSIVE 100
91 #define LBS_DWELL_ACTIVE 40
94 /***************************************************************************
95 * Misc utility functions
97 * TLVs are Marvell specific. They are very similar to IEs, they have the
98 * same structure: type, length, data*. The only difference: for IEs, the
99 * type and length are u8, but for TLVs they're __le16.
103 * Convert NL80211's auth_type to the one from Libertas, see chapter 5.9.1
104 * in the firmware spec
106 static u8
lbs_auth_to_authtype(enum nl80211_auth_type auth_type
)
111 case NL80211_AUTHTYPE_OPEN_SYSTEM
:
112 case NL80211_AUTHTYPE_SHARED_KEY
:
115 case NL80211_AUTHTYPE_AUTOMATIC
:
116 ret
= NL80211_AUTHTYPE_OPEN_SYSTEM
;
118 case NL80211_AUTHTYPE_NETWORK_EAP
:
122 /* silence compiler */
130 * Various firmware commands need the list of supported rates, but with
131 * the hight-bit set for basic rates
133 static int lbs_add_rates(u8
*rates
)
137 for (i
= 0; i
< ARRAY_SIZE(lbs_rates
); i
++) {
138 u8 rate
= lbs_rates
[i
].bitrate
/ 5;
139 if (rate
== 0x02 || rate
== 0x04 ||
140 rate
== 0x0b || rate
== 0x16)
144 return ARRAY_SIZE(lbs_rates
);
148 /***************************************************************************
149 * TLV utility functions
151 * TLVs are Marvell specific. They are very similar to IEs, they have the
152 * same structure: type, length, data*. The only difference: for IEs, the
153 * type and length are u8, but for TLVs they're __le16.
160 #define LBS_MAX_SSID_TLV_SIZE \
161 (sizeof(struct mrvl_ie_header) \
162 + IEEE80211_MAX_SSID_LEN)
164 static int lbs_add_ssid_tlv(u8
*tlv
, const u8
*ssid
, int ssid_len
)
166 struct mrvl_ie_ssid_param_set
*ssid_tlv
= (void *)tlv
;
171 * ssid 4d 4e 54 45 53 54
173 ssid_tlv
->header
.type
= cpu_to_le16(TLV_TYPE_SSID
);
174 ssid_tlv
->header
.len
= cpu_to_le16(ssid_len
);
175 memcpy(ssid_tlv
->ssid
, ssid
, ssid_len
);
176 return sizeof(ssid_tlv
->header
) + ssid_len
;
181 * Add channel list TLV (section 8.4.2)
183 * Actual channel data comes from priv->wdev->wiphy->channels.
185 #define LBS_MAX_CHANNEL_LIST_TLV_SIZE \
186 (sizeof(struct mrvl_ie_header) \
187 + (LBS_SCAN_BEFORE_NAP * sizeof(struct chanscanparamset)))
189 static int lbs_add_channel_list_tlv(struct lbs_private
*priv
, u8
*tlv
,
190 int last_channel
, int active_scan
)
192 int chanscanparamsize
= sizeof(struct chanscanparamset
) *
193 (last_channel
- priv
->scan_channel
);
195 struct mrvl_ie_header
*header
= (void *) tlv
;
198 * TLV-ID CHANLIST 01 01
200 * channel 00 01 00 00 00 64 00
204 * min scan time 00 00
205 * max scan time 64 00
206 * channel 2 00 02 00 00 00 64 00
210 header
->type
= cpu_to_le16(TLV_TYPE_CHANLIST
);
211 header
->len
= cpu_to_le16(chanscanparamsize
);
212 tlv
+= sizeof(struct mrvl_ie_header
);
214 /* lbs_deb_scan("scan: channels %d to %d\n", priv->scan_channel,
216 memset(tlv
, 0, chanscanparamsize
);
218 while (priv
->scan_channel
< last_channel
) {
219 struct chanscanparamset
*param
= (void *) tlv
;
221 param
->radiotype
= CMD_SCAN_RADIO_TYPE_BG
;
223 priv
->scan_req
->channels
[priv
->scan_channel
]->hw_value
;
225 param
->maxscantime
= cpu_to_le16(LBS_DWELL_ACTIVE
);
227 param
->chanscanmode
.passivescan
= 1;
228 param
->maxscantime
= cpu_to_le16(LBS_DWELL_PASSIVE
);
230 tlv
+= sizeof(struct chanscanparamset
);
231 priv
->scan_channel
++;
233 return sizeof(struct mrvl_ie_header
) + chanscanparamsize
;
240 * The rates are in lbs_bg_rates[], but for the 802.11b
241 * rates the high bit is set. We add this TLV only because
242 * there's a firmware which otherwise doesn't report all
245 #define LBS_MAX_RATES_TLV_SIZE \
246 (sizeof(struct mrvl_ie_header) \
247 + (ARRAY_SIZE(lbs_rates)))
249 /* Adds a TLV with all rates the hardware supports */
250 static int lbs_add_supported_rates_tlv(u8
*tlv
)
253 struct mrvl_ie_rates_param_set
*rate_tlv
= (void *)tlv
;
258 * rates 82 84 8b 96 0c 12 18 24 30 48 60 6c
260 rate_tlv
->header
.type
= cpu_to_le16(TLV_TYPE_RATES
);
261 tlv
+= sizeof(rate_tlv
->header
);
262 i
= lbs_add_rates(tlv
);
264 rate_tlv
->header
.len
= cpu_to_le16(i
);
265 return sizeof(rate_tlv
->header
) + i
;
268 /* Add common rates from a TLV and return the new end of the TLV */
270 add_ie_rates(u8
*tlv
, const u8
*ie
, int *nrates
)
272 int hw
, ap
, ap_max
= ie
[1];
275 /* Advance past IE header */
278 lbs_deb_hex(LBS_DEB_ASSOC
, "AP IE Rates", (u8
*) ie
, ap_max
);
280 for (hw
= 0; hw
< ARRAY_SIZE(lbs_rates
); hw
++) {
281 hw_rate
= lbs_rates
[hw
].bitrate
/ 5;
282 for (ap
= 0; ap
< ap_max
; ap
++) {
283 if (hw_rate
== (ie
[ap
] & 0x7f)) {
285 *nrates
= *nrates
+ 1;
293 * Adds a TLV with all rates the hardware *and* BSS supports.
295 static int lbs_add_common_rates_tlv(u8
*tlv
, struct cfg80211_bss
*bss
)
297 struct mrvl_ie_rates_param_set
*rate_tlv
= (void *)tlv
;
298 const u8
*rates_eid
, *ext_rates_eid
;
301 rates_eid
= ieee80211_bss_get_ie(bss
, WLAN_EID_SUPP_RATES
);
302 ext_rates_eid
= ieee80211_bss_get_ie(bss
, WLAN_EID_EXT_SUPP_RATES
);
305 * 01 00 TLV_TYPE_RATES
309 rate_tlv
->header
.type
= cpu_to_le16(TLV_TYPE_RATES
);
310 tlv
+= sizeof(rate_tlv
->header
);
312 /* Add basic rates */
314 tlv
= add_ie_rates(tlv
, rates_eid
, &n
);
316 /* Add extended rates, if any */
318 tlv
= add_ie_rates(tlv
, ext_rates_eid
, &n
);
320 lbs_deb_assoc("assoc: bss had no basic rate IE\n");
321 /* Fallback: add basic 802.11b rates */
329 rate_tlv
->header
.len
= cpu_to_le16(n
);
330 return sizeof(rate_tlv
->header
) + n
;
337 * This is only needed for newer firmware (V9 and up).
339 #define LBS_MAX_AUTH_TYPE_TLV_SIZE \
340 sizeof(struct mrvl_ie_auth_type)
342 static int lbs_add_auth_type_tlv(u8
*tlv
, enum nl80211_auth_type auth_type
)
344 struct mrvl_ie_auth_type
*auth
= (void *) tlv
;
347 * 1f 01 TLV_TYPE_AUTH_TYPE
351 auth
->header
.type
= cpu_to_le16(TLV_TYPE_AUTH_TYPE
);
352 auth
->header
.len
= cpu_to_le16(sizeof(*auth
)-sizeof(auth
->header
));
353 auth
->auth
= cpu_to_le16(lbs_auth_to_authtype(auth_type
));
354 return sizeof(*auth
);
359 * Add channel (phy ds) TLV
361 #define LBS_MAX_CHANNEL_TLV_SIZE \
362 sizeof(struct mrvl_ie_header)
364 static int lbs_add_channel_tlv(u8
*tlv
, u8 channel
)
366 struct mrvl_ie_ds_param_set
*ds
= (void *) tlv
;
369 * 03 00 TLV_TYPE_PHY_DS
373 ds
->header
.type
= cpu_to_le16(TLV_TYPE_PHY_DS
);
374 ds
->header
.len
= cpu_to_le16(sizeof(*ds
)-sizeof(ds
->header
));
375 ds
->channel
= channel
;
381 * Add (empty) CF param TLV of the form:
383 #define LBS_MAX_CF_PARAM_TLV_SIZE \
384 sizeof(struct mrvl_ie_header)
386 static int lbs_add_cf_param_tlv(u8
*tlv
)
388 struct mrvl_ie_cf_param_set
*cf
= (void *)tlv
;
395 * 00 00 cfpmaxduration
396 * 00 00 cfpdurationremaining
398 cf
->header
.type
= cpu_to_le16(TLV_TYPE_CF
);
399 cf
->header
.len
= cpu_to_le16(sizeof(*cf
)-sizeof(cf
->header
));
406 #define LBS_MAX_WPA_TLV_SIZE \
407 (sizeof(struct mrvl_ie_header) \
408 + 128 /* TODO: I guessed the size */)
410 static int lbs_add_wpa_tlv(u8
*tlv
, const u8
*ie
, u8 ie_len
)
415 * We need just convert an IE to an TLV. IEs use u8 for the header,
419 * but TLVs use __le16 instead:
426 tlv_len
= *tlv
++ = *ie
++;
430 /* the TLV is two bytes larger than the IE */
438 static int lbs_cfg_set_channel(struct wiphy
*wiphy
,
439 struct net_device
*netdev
,
440 struct ieee80211_channel
*channel
,
441 enum nl80211_channel_type channel_type
)
443 struct lbs_private
*priv
= wiphy_priv(wiphy
);
446 lbs_deb_enter_args(LBS_DEB_CFG80211
, "iface %s freq %d, type %d",
447 netdev_name(netdev
), channel
->center_freq
, channel_type
);
449 if (channel_type
!= NL80211_CHAN_NO_HT
)
452 if (netdev
== priv
->mesh_dev
)
453 ret
= lbs_mesh_set_channel(priv
, channel
->hw_value
);
455 ret
= lbs_set_channel(priv
, channel
->hw_value
);
458 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
469 * When scanning, the firmware doesn't send a nul packet with the power-safe
470 * bit to the AP. So we cannot stay away from our current channel too long,
471 * otherwise we loose data. So take a "nap" while scanning every other
474 #define LBS_SCAN_BEFORE_NAP 4
478 * When the firmware reports back a scan-result, it gives us an "u8 rssi",
479 * which isn't really an RSSI, as it becomes larger when moving away from
480 * the AP. Anyway, we need to convert that into mBm.
482 #define LBS_SCAN_RSSI_TO_MBM(rssi) \
483 ((-(int)rssi + 3)*100)
485 static int lbs_ret_scan(struct lbs_private
*priv
, unsigned long dummy
,
486 struct cmd_header
*resp
)
488 struct cmd_ds_802_11_scan_rsp
*scanresp
= (void *)resp
;
496 lbs_deb_enter(LBS_DEB_CFG80211
);
498 bsssize
= get_unaligned_le16(&scanresp
->bssdescriptsize
);
500 lbs_deb_scan("scan response: %d BSSs (%d bytes); resp size %d bytes\n",
501 scanresp
->nr_sets
, bsssize
, le16_to_cpu(resp
->size
));
503 if (scanresp
->nr_sets
== 0) {
509 * The general layout of the scan response is described in chapter
510 * 5.7.1. Basically we have a common part, then any number of BSS
511 * descriptor sections. Finally we have section with the same number
514 * cmd_ds_802_11_scan_rsp
527 * MrvlIEtypes_TsfFimestamp_t
533 pos
= scanresp
->bssdesc_and_tlvbuffer
;
535 lbs_deb_hex(LBS_DEB_SCAN
, "SCAN_RSP", scanresp
->bssdesc_and_tlvbuffer
,
536 scanresp
->bssdescriptsize
);
538 tsfdesc
= pos
+ bsssize
;
539 tsfsize
= 4 + 8 * scanresp
->nr_sets
;
540 lbs_deb_hex(LBS_DEB_SCAN
, "SCAN_TSF", (u8
*) tsfdesc
, tsfsize
);
542 /* Validity check: we expect a Marvell-Local TLV */
543 i
= get_unaligned_le16(tsfdesc
);
545 if (i
!= TLV_TYPE_TSFTIMESTAMP
) {
546 lbs_deb_scan("scan response: invalid TSF Timestamp %d\n", i
);
551 * Validity check: the TLV holds TSF values with 8 bytes each, so
552 * the size in the TLV must match the nr_sets value
554 i
= get_unaligned_le16(tsfdesc
);
556 if (i
/ 8 != scanresp
->nr_sets
) {
557 lbs_deb_scan("scan response: invalid number of TSF timestamp "
558 "sets (expected %d got %d)\n", scanresp
->nr_sets
,
563 for (i
= 0; i
< scanresp
->nr_sets
; i
++) {
572 const u8
*ssid
= NULL
;
574 DECLARE_SSID_BUF(ssid_buf
);
576 int len
= get_unaligned_le16(pos
);
584 /* Packet time stamp */
586 /* Beacon interval */
587 intvl
= get_unaligned_le16(pos
);
590 capa
= get_unaligned_le16(pos
);
593 /* To find out the channel, we must parse the IEs */
596 * 6+1+8+2+2: size of BSSID, RSSI, time stamp, beacon
597 * interval, capabilities
599 ielen
= left
= len
- (6 + 1 + 8 + 2 + 2);
605 if (elen
> left
|| elen
== 0) {
606 lbs_deb_scan("scan response: invalid IE fmt\n");
610 if (id
== WLAN_EID_DS_PARAMS
)
612 if (id
== WLAN_EID_SSID
) {
620 /* No channel, no luck */
622 struct wiphy
*wiphy
= priv
->wdev
->wiphy
;
623 int freq
= ieee80211_channel_to_frequency(chan_no
,
624 IEEE80211_BAND_2GHZ
);
625 struct ieee80211_channel
*channel
=
626 ieee80211_get_channel(wiphy
, freq
);
628 lbs_deb_scan("scan: %pM, capa %04x, chan %2d, %s, "
630 bssid
, capa
, chan_no
,
631 print_ssid(ssid_buf
, ssid
, ssid_len
),
632 LBS_SCAN_RSSI_TO_MBM(rssi
)/100);
635 !(channel
->flags
& IEEE80211_CHAN_DISABLED
))
636 cfg80211_inform_bss(wiphy
, channel
,
637 bssid
, get_unaligned_le64(tsfdesc
),
638 capa
, intvl
, ie
, ielen
,
639 LBS_SCAN_RSSI_TO_MBM(rssi
),
642 lbs_deb_scan("scan response: missing BSS channel IE\n");
649 lbs_deb_leave_args(LBS_DEB_SCAN
, "ret %d", ret
);
655 * Our scan command contains a TLV, consting of a SSID TLV, a channel list
656 * TLV and a rates TLV. Determine the maximum size of them:
658 #define LBS_SCAN_MAX_CMD_SIZE \
659 (sizeof(struct cmd_ds_802_11_scan) \
660 + LBS_MAX_SSID_TLV_SIZE \
661 + LBS_MAX_CHANNEL_LIST_TLV_SIZE \
662 + LBS_MAX_RATES_TLV_SIZE)
665 * Assumes priv->scan_req is initialized and valid
666 * Assumes priv->scan_channel is initialized
668 static void lbs_scan_worker(struct work_struct
*work
)
670 struct lbs_private
*priv
=
671 container_of(work
, struct lbs_private
, scan_work
.work
);
672 struct cmd_ds_802_11_scan
*scan_cmd
;
673 u8
*tlv
; /* pointer into our current, growing TLV storage area */
675 int running
, carrier
;
677 lbs_deb_enter(LBS_DEB_SCAN
);
679 scan_cmd
= kzalloc(LBS_SCAN_MAX_CMD_SIZE
, GFP_KERNEL
);
680 if (scan_cmd
== NULL
)
681 goto out_no_scan_cmd
;
683 /* prepare fixed part of scan command */
684 scan_cmd
->bsstype
= CMD_BSS_TYPE_ANY
;
686 /* stop network while we're away from our main channel */
687 running
= !netif_queue_stopped(priv
->dev
);
688 carrier
= netif_carrier_ok(priv
->dev
);
690 netif_stop_queue(priv
->dev
);
692 netif_carrier_off(priv
->dev
);
694 /* prepare fixed part of scan command */
695 tlv
= scan_cmd
->tlvbuffer
;
698 if (priv
->scan_req
->n_ssids
&& priv
->scan_req
->ssids
[0].ssid_len
> 0)
699 tlv
+= lbs_add_ssid_tlv(tlv
,
700 priv
->scan_req
->ssids
[0].ssid
,
701 priv
->scan_req
->ssids
[0].ssid_len
);
703 /* add channel TLVs */
704 last_channel
= priv
->scan_channel
+ LBS_SCAN_BEFORE_NAP
;
705 if (last_channel
> priv
->scan_req
->n_channels
)
706 last_channel
= priv
->scan_req
->n_channels
;
707 tlv
+= lbs_add_channel_list_tlv(priv
, tlv
, last_channel
,
708 priv
->scan_req
->n_ssids
);
711 tlv
+= lbs_add_supported_rates_tlv(tlv
);
713 if (priv
->scan_channel
< priv
->scan_req
->n_channels
) {
714 cancel_delayed_work(&priv
->scan_work
);
715 if (netif_running(priv
->dev
))
716 queue_delayed_work(priv
->work_thread
, &priv
->scan_work
,
717 msecs_to_jiffies(300));
720 /* This is the final data we are about to send */
721 scan_cmd
->hdr
.size
= cpu_to_le16(tlv
- (u8
*)scan_cmd
);
722 lbs_deb_hex(LBS_DEB_SCAN
, "SCAN_CMD", (void *)scan_cmd
,
724 lbs_deb_hex(LBS_DEB_SCAN
, "SCAN_TLV", scan_cmd
->tlvbuffer
,
725 tlv
- scan_cmd
->tlvbuffer
);
727 __lbs_cmd(priv
, CMD_802_11_SCAN
, &scan_cmd
->hdr
,
728 le16_to_cpu(scan_cmd
->hdr
.size
),
731 if (priv
->scan_channel
>= priv
->scan_req
->n_channels
)
735 /* Restart network */
737 netif_carrier_on(priv
->dev
);
738 if (running
&& !priv
->tx_pending_len
)
739 netif_wake_queue(priv
->dev
);
743 /* Wake up anything waiting on scan completion */
744 if (priv
->scan_req
== NULL
) {
745 lbs_deb_scan("scan: waking up waiters\n");
746 wake_up_all(&priv
->scan_q
);
750 lbs_deb_leave(LBS_DEB_SCAN
);
753 static void _internal_start_scan(struct lbs_private
*priv
, bool internal
,
754 struct cfg80211_scan_request
*request
)
756 lbs_deb_enter(LBS_DEB_CFG80211
);
758 lbs_deb_scan("scan: ssids %d, channels %d, ie_len %zd\n",
759 request
->n_ssids
, request
->n_channels
, request
->ie_len
);
761 priv
->scan_channel
= 0;
762 queue_delayed_work(priv
->work_thread
, &priv
->scan_work
,
763 msecs_to_jiffies(50));
765 priv
->scan_req
= request
;
766 priv
->internal_scan
= internal
;
768 lbs_deb_leave(LBS_DEB_CFG80211
);
772 * Clean up priv->scan_req. Should be used to handle the allocation details.
774 void lbs_scan_done(struct lbs_private
*priv
)
776 WARN_ON(!priv
->scan_req
);
778 if (priv
->internal_scan
)
779 kfree(priv
->scan_req
);
781 cfg80211_scan_done(priv
->scan_req
, false);
783 priv
->scan_req
= NULL
;
786 static int lbs_cfg_scan(struct wiphy
*wiphy
,
787 struct net_device
*dev
,
788 struct cfg80211_scan_request
*request
)
790 struct lbs_private
*priv
= wiphy_priv(wiphy
);
793 lbs_deb_enter(LBS_DEB_CFG80211
);
795 if (priv
->scan_req
|| delayed_work_pending(&priv
->scan_work
)) {
796 /* old scan request not yet processed */
801 _internal_start_scan(priv
, false, request
);
803 if (priv
->surpriseremoved
)
807 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
818 void lbs_send_disconnect_notification(struct lbs_private
*priv
)
820 lbs_deb_enter(LBS_DEB_CFG80211
);
822 cfg80211_disconnected(priv
->dev
,
827 lbs_deb_leave(LBS_DEB_CFG80211
);
830 void lbs_send_mic_failureevent(struct lbs_private
*priv
, u32 event
)
832 lbs_deb_enter(LBS_DEB_CFG80211
);
834 cfg80211_michael_mic_failure(priv
->dev
,
836 event
== MACREG_INT_CODE_MIC_ERR_MULTICAST
?
837 NL80211_KEYTYPE_GROUP
:
838 NL80211_KEYTYPE_PAIRWISE
,
843 lbs_deb_leave(LBS_DEB_CFG80211
);
855 * This removes all WEP keys
857 static int lbs_remove_wep_keys(struct lbs_private
*priv
)
859 struct cmd_ds_802_11_set_wep cmd
;
862 lbs_deb_enter(LBS_DEB_CFG80211
);
864 memset(&cmd
, 0, sizeof(cmd
));
865 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
866 cmd
.keyindex
= cpu_to_le16(priv
->wep_tx_key
);
867 cmd
.action
= cpu_to_le16(CMD_ACT_REMOVE
);
869 ret
= lbs_cmd_with_response(priv
, CMD_802_11_SET_WEP
, &cmd
);
871 lbs_deb_leave(LBS_DEB_CFG80211
);
878 static int lbs_set_wep_keys(struct lbs_private
*priv
)
880 struct cmd_ds_802_11_set_wep cmd
;
884 lbs_deb_enter(LBS_DEB_CFG80211
);
891 * action 02 00 ACT_ADD
893 * type for key 1 01 WEP40
897 * key 1 39 39 39 39 39 00 00 00
898 * 00 00 00 00 00 00 00 00
899 * key 2 00 00 00 00 00 00 00 00
900 * 00 00 00 00 00 00 00 00
901 * key 3 00 00 00 00 00 00 00 00
902 * 00 00 00 00 00 00 00 00
903 * key 4 00 00 00 00 00 00 00 00
905 if (priv
->wep_key_len
[0] || priv
->wep_key_len
[1] ||
906 priv
->wep_key_len
[2] || priv
->wep_key_len
[3]) {
907 /* Only set wep keys if we have at least one of them */
908 memset(&cmd
, 0, sizeof(cmd
));
909 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
910 cmd
.keyindex
= cpu_to_le16(priv
->wep_tx_key
);
911 cmd
.action
= cpu_to_le16(CMD_ACT_ADD
);
913 for (i
= 0; i
< 4; i
++) {
914 switch (priv
->wep_key_len
[i
]) {
915 case WLAN_KEY_LEN_WEP40
:
916 cmd
.keytype
[i
] = CMD_TYPE_WEP_40_BIT
;
918 case WLAN_KEY_LEN_WEP104
:
919 cmd
.keytype
[i
] = CMD_TYPE_WEP_104_BIT
;
925 memcpy(cmd
.keymaterial
[i
], priv
->wep_key
[i
],
926 priv
->wep_key_len
[i
]);
929 ret
= lbs_cmd_with_response(priv
, CMD_802_11_SET_WEP
, &cmd
);
931 /* Otherwise remove all wep keys */
932 ret
= lbs_remove_wep_keys(priv
);
935 lbs_deb_leave(LBS_DEB_CFG80211
);
941 * Enable/Disable RSN status
943 static int lbs_enable_rsn(struct lbs_private
*priv
, int enable
)
945 struct cmd_ds_802_11_enable_rsn cmd
;
948 lbs_deb_enter_args(LBS_DEB_CFG80211
, "%d", enable
);
955 * action 01 00 ACT_SET
958 memset(&cmd
, 0, sizeof(cmd
));
959 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
960 cmd
.action
= cpu_to_le16(CMD_ACT_SET
);
961 cmd
.enable
= cpu_to_le16(enable
);
963 ret
= lbs_cmd_with_response(priv
, CMD_802_11_ENABLE_RSN
, &cmd
);
965 lbs_deb_leave(LBS_DEB_CFG80211
);
971 * Set WPA/WPA key material
975 * like "struct cmd_ds_802_11_key_material", but with cmd_header. Once we
976 * get rid of WEXT, this should go into host.h
979 struct cmd_key_material
{
980 struct cmd_header hdr
;
983 struct MrvlIEtype_keyParamSet param
;
986 static int lbs_set_key_material(struct lbs_private
*priv
,
989 u8
*key
, u16 key_len
)
991 struct cmd_key_material cmd
;
994 lbs_deb_enter(LBS_DEB_CFG80211
);
997 * Example for WPA (TKIP):
1004 * TLV type 00 01 key param
1006 * key type 01 00 TKIP
1007 * key info 06 00 UNICAST | ENABLED
1011 memset(&cmd
, 0, sizeof(cmd
));
1012 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
1013 cmd
.action
= cpu_to_le16(CMD_ACT_SET
);
1014 cmd
.param
.type
= cpu_to_le16(TLV_TYPE_KEY_MATERIAL
);
1015 cmd
.param
.length
= cpu_to_le16(sizeof(cmd
.param
) - 4);
1016 cmd
.param
.keytypeid
= cpu_to_le16(key_type
);
1017 cmd
.param
.keyinfo
= cpu_to_le16(key_info
);
1018 cmd
.param
.keylen
= cpu_to_le16(key_len
);
1020 memcpy(cmd
.param
.key
, key
, key_len
);
1022 ret
= lbs_cmd_with_response(priv
, CMD_802_11_KEY_MATERIAL
, &cmd
);
1024 lbs_deb_leave(LBS_DEB_CFG80211
);
1030 * Sets the auth type (open, shared, etc) in the firmware. That
1031 * we use CMD_802_11_AUTHENTICATE is misleading, this firmware
1032 * command doesn't send an authentication frame at all, it just
1033 * stores the auth_type.
1035 static int lbs_set_authtype(struct lbs_private
*priv
,
1036 struct cfg80211_connect_params
*sme
)
1038 struct cmd_ds_802_11_authenticate cmd
;
1041 lbs_deb_enter_args(LBS_DEB_CFG80211
, "%d", sme
->auth_type
);
1048 * BSS id 00 13 19 80 da 30
1050 * reserved 00 00 00 00 00 00 00 00 00 00
1052 memset(&cmd
, 0, sizeof(cmd
));
1053 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
1055 memcpy(cmd
.bssid
, sme
->bssid
, ETH_ALEN
);
1056 /* convert auth_type */
1057 ret
= lbs_auth_to_authtype(sme
->auth_type
);
1062 ret
= lbs_cmd_with_response(priv
, CMD_802_11_AUTHENTICATE
, &cmd
);
1065 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1071 * Create association request
1073 #define LBS_ASSOC_MAX_CMD_SIZE \
1074 (sizeof(struct cmd_ds_802_11_associate) \
1075 - 512 /* cmd_ds_802_11_associate.iebuf */ \
1076 + LBS_MAX_SSID_TLV_SIZE \
1077 + LBS_MAX_CHANNEL_TLV_SIZE \
1078 + LBS_MAX_CF_PARAM_TLV_SIZE \
1079 + LBS_MAX_AUTH_TYPE_TLV_SIZE \
1080 + LBS_MAX_WPA_TLV_SIZE)
1082 static int lbs_associate(struct lbs_private
*priv
,
1083 struct cfg80211_bss
*bss
,
1084 struct cfg80211_connect_params
*sme
)
1086 struct cmd_ds_802_11_associate_response
*resp
;
1087 struct cmd_ds_802_11_associate
*cmd
= kzalloc(LBS_ASSOC_MAX_CMD_SIZE
,
1090 size_t len
, resp_ie_len
;
1093 u8
*pos
= &(cmd
->iebuf
[0]);
1096 lbs_deb_enter(LBS_DEB_CFG80211
);
1108 * BSS id 00 13 19 80 da 30
1109 * capabilities 11 00
1110 * listen interval 0a 00
1111 * beacon interval 00 00
1113 * TLVs xx (up to 512 bytes)
1115 cmd
->hdr
.command
= cpu_to_le16(CMD_802_11_ASSOCIATE
);
1117 /* Fill in static fields */
1118 memcpy(cmd
->bssid
, bss
->bssid
, ETH_ALEN
);
1119 cmd
->listeninterval
= cpu_to_le16(MRVDRV_DEFAULT_LISTEN_INTERVAL
);
1120 cmd
->capability
= cpu_to_le16(bss
->capability
);
1123 ssid_eid
= ieee80211_bss_get_ie(bss
, WLAN_EID_SSID
);
1125 pos
+= lbs_add_ssid_tlv(pos
, ssid_eid
+ 2, ssid_eid
[1]);
1127 lbs_deb_assoc("no SSID\n");
1129 /* add DS param TLV */
1131 pos
+= lbs_add_channel_tlv(pos
, bss
->channel
->hw_value
);
1133 lbs_deb_assoc("no channel\n");
1135 /* add (empty) CF param TLV */
1136 pos
+= lbs_add_cf_param_tlv(pos
);
1139 tmp
= pos
+ 4; /* skip Marvell IE header */
1140 pos
+= lbs_add_common_rates_tlv(pos
, bss
);
1141 lbs_deb_hex(LBS_DEB_ASSOC
, "Common Rates", tmp
, pos
- tmp
);
1143 /* add auth type TLV */
1144 if (MRVL_FW_MAJOR_REV(priv
->fwrelease
) >= 9)
1145 pos
+= lbs_add_auth_type_tlv(pos
, sme
->auth_type
);
1147 /* add WPA/WPA2 TLV */
1148 if (sme
->ie
&& sme
->ie_len
)
1149 pos
+= lbs_add_wpa_tlv(pos
, sme
->ie
, sme
->ie_len
);
1151 len
= (sizeof(*cmd
) - sizeof(cmd
->iebuf
)) +
1152 (u16
)(pos
- (u8
*) &cmd
->iebuf
);
1153 cmd
->hdr
.size
= cpu_to_le16(len
);
1155 lbs_deb_hex(LBS_DEB_ASSOC
, "ASSOC_CMD", (u8
*) cmd
,
1156 le16_to_cpu(cmd
->hdr
.size
));
1158 /* store for later use */
1159 memcpy(priv
->assoc_bss
, bss
->bssid
, ETH_ALEN
);
1161 ret
= lbs_cmd_with_response(priv
, CMD_802_11_ASSOCIATE
, cmd
);
1165 /* generate connect message to cfg80211 */
1167 resp
= (void *) cmd
; /* recast for easier field access */
1168 status
= le16_to_cpu(resp
->statuscode
);
1170 /* Older FW versions map the IEEE 802.11 Status Code in the association
1171 * response to the following values returned in resp->statuscode:
1173 * IEEE Status Code Marvell Status Code
1174 * 0 -> 0x0000 ASSOC_RESULT_SUCCESS
1175 * 13 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
1176 * 14 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
1177 * 15 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
1178 * 16 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
1179 * others -> 0x0003 ASSOC_RESULT_REFUSED
1181 * Other response codes:
1182 * 0x0001 -> ASSOC_RESULT_INVALID_PARAMETERS (unused)
1183 * 0x0002 -> ASSOC_RESULT_TIMEOUT (internal timer expired waiting for
1184 * association response from the AP)
1186 if (MRVL_FW_MAJOR_REV(priv
->fwrelease
) <= 8) {
1191 lbs_deb_assoc("invalid association parameters\n");
1192 status
= WLAN_STATUS_CAPS_UNSUPPORTED
;
1195 lbs_deb_assoc("timer expired while waiting for AP\n");
1196 status
= WLAN_STATUS_AUTH_TIMEOUT
;
1199 lbs_deb_assoc("association refused by AP\n");
1200 status
= WLAN_STATUS_ASSOC_DENIED_UNSPEC
;
1203 lbs_deb_assoc("authentication refused by AP\n");
1204 status
= WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION
;
1207 lbs_deb_assoc("association failure %d\n", status
);
1208 /* v5 OLPC firmware does return the AP status code if
1209 * it's not one of the values above. Let that through.
1215 lbs_deb_assoc("status %d, statuscode 0x%04x, capability 0x%04x, "
1216 "aid 0x%04x\n", status
, le16_to_cpu(resp
->statuscode
),
1217 le16_to_cpu(resp
->capability
), le16_to_cpu(resp
->aid
));
1219 resp_ie_len
= le16_to_cpu(resp
->hdr
.size
)
1222 cfg80211_connect_result(priv
->dev
,
1224 sme
->ie
, sme
->ie_len
,
1225 resp
->iebuf
, resp_ie_len
,
1230 /* TODO: get rid of priv->connect_status */
1231 priv
->connect_status
= LBS_CONNECTED
;
1232 netif_carrier_on(priv
->dev
);
1233 if (!priv
->tx_pending_len
)
1234 netif_tx_wake_all_queues(priv
->dev
);
1238 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1242 static struct cfg80211_scan_request
*
1243 _new_connect_scan_req(struct wiphy
*wiphy
, struct cfg80211_connect_params
*sme
)
1245 struct cfg80211_scan_request
*creq
= NULL
;
1246 int i
, n_channels
= 0;
1247 enum ieee80211_band band
;
1249 for (band
= 0; band
< IEEE80211_NUM_BANDS
; band
++) {
1250 if (wiphy
->bands
[band
])
1251 n_channels
+= wiphy
->bands
[band
]->n_channels
;
1254 creq
= kzalloc(sizeof(*creq
) + sizeof(struct cfg80211_ssid
) +
1255 n_channels
* sizeof(void *),
1260 /* SSIDs come after channels */
1261 creq
->ssids
= (void *)&creq
->channels
[n_channels
];
1262 creq
->n_channels
= n_channels
;
1265 /* Scan all available channels */
1267 for (band
= 0; band
< IEEE80211_NUM_BANDS
; band
++) {
1270 if (!wiphy
->bands
[band
])
1273 for (j
= 0; j
< wiphy
->bands
[band
]->n_channels
; j
++) {
1274 /* ignore disabled channels */
1275 if (wiphy
->bands
[band
]->channels
[j
].flags
&
1276 IEEE80211_CHAN_DISABLED
)
1279 creq
->channels
[i
] = &wiphy
->bands
[band
]->channels
[j
];
1284 /* Set real number of channels specified in creq->channels[] */
1285 creq
->n_channels
= i
;
1287 /* Scan for the SSID we're going to connect to */
1288 memcpy(creq
->ssids
[0].ssid
, sme
->ssid
, sme
->ssid_len
);
1289 creq
->ssids
[0].ssid_len
= sme
->ssid_len
;
1291 /* No channels found... */
1299 static int lbs_cfg_connect(struct wiphy
*wiphy
, struct net_device
*dev
,
1300 struct cfg80211_connect_params
*sme
)
1302 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1303 struct cfg80211_bss
*bss
= NULL
;
1305 u8 preamble
= RADIO_PREAMBLE_SHORT
;
1307 if (dev
== priv
->mesh_dev
)
1310 lbs_deb_enter(LBS_DEB_CFG80211
);
1313 struct cfg80211_scan_request
*creq
;
1316 * Scan for the requested network after waiting for existing
1319 lbs_deb_assoc("assoc: waiting for existing scans\n");
1320 wait_event_interruptible_timeout(priv
->scan_q
,
1321 (priv
->scan_req
== NULL
),
1324 creq
= _new_connect_scan_req(wiphy
, sme
);
1330 lbs_deb_assoc("assoc: scanning for compatible AP\n");
1331 _internal_start_scan(priv
, true, creq
);
1333 lbs_deb_assoc("assoc: waiting for scan to complete\n");
1334 wait_event_interruptible_timeout(priv
->scan_q
,
1335 (priv
->scan_req
== NULL
),
1337 lbs_deb_assoc("assoc: scanning competed\n");
1340 /* Find the BSS we want using available scan results */
1341 bss
= cfg80211_get_bss(wiphy
, sme
->channel
, sme
->bssid
,
1342 sme
->ssid
, sme
->ssid_len
,
1343 WLAN_CAPABILITY_ESS
, WLAN_CAPABILITY_ESS
);
1345 wiphy_err(wiphy
, "assoc: bss %pM not in scan results\n",
1350 lbs_deb_assoc("trying %pM\n", bss
->bssid
);
1351 lbs_deb_assoc("cipher 0x%x, key index %d, key len %d\n",
1352 sme
->crypto
.cipher_group
,
1353 sme
->key_idx
, sme
->key_len
);
1355 /* As this is a new connection, clear locally stored WEP keys */
1356 priv
->wep_tx_key
= 0;
1357 memset(priv
->wep_key
, 0, sizeof(priv
->wep_key
));
1358 memset(priv
->wep_key_len
, 0, sizeof(priv
->wep_key_len
));
1360 /* set/remove WEP keys */
1361 switch (sme
->crypto
.cipher_group
) {
1362 case WLAN_CIPHER_SUITE_WEP40
:
1363 case WLAN_CIPHER_SUITE_WEP104
:
1364 /* Store provided WEP keys in priv-> */
1365 priv
->wep_tx_key
= sme
->key_idx
;
1366 priv
->wep_key_len
[sme
->key_idx
] = sme
->key_len
;
1367 memcpy(priv
->wep_key
[sme
->key_idx
], sme
->key
, sme
->key_len
);
1368 /* Set WEP keys and WEP mode */
1369 lbs_set_wep_keys(priv
);
1370 priv
->mac_control
|= CMD_ACT_MAC_WEP_ENABLE
;
1371 lbs_set_mac_control(priv
);
1372 /* No RSN mode for WEP */
1373 lbs_enable_rsn(priv
, 0);
1375 case 0: /* there's no WLAN_CIPHER_SUITE_NONE definition */
1377 * If we don't have no WEP, no WPA and no WPA2,
1378 * we remove all keys like in the WPA/WPA2 setup,
1379 * we just don't set RSN.
1381 * Therefore: fall-through
1383 case WLAN_CIPHER_SUITE_TKIP
:
1384 case WLAN_CIPHER_SUITE_CCMP
:
1385 /* Remove WEP keys and WEP mode */
1386 lbs_remove_wep_keys(priv
);
1387 priv
->mac_control
&= ~CMD_ACT_MAC_WEP_ENABLE
;
1388 lbs_set_mac_control(priv
);
1390 /* clear the WPA/WPA2 keys */
1391 lbs_set_key_material(priv
,
1392 KEY_TYPE_ID_WEP
, /* doesn't matter */
1393 KEY_INFO_WPA_UNICAST
,
1395 lbs_set_key_material(priv
,
1396 KEY_TYPE_ID_WEP
, /* doesn't matter */
1399 /* RSN mode for WPA/WPA2 */
1400 lbs_enable_rsn(priv
, sme
->crypto
.cipher_group
!= 0);
1403 wiphy_err(wiphy
, "unsupported cipher group 0x%x\n",
1404 sme
->crypto
.cipher_group
);
1409 lbs_set_authtype(priv
, sme
);
1410 lbs_set_radio(priv
, preamble
, 1);
1412 /* Do the actual association */
1413 ret
= lbs_associate(priv
, bss
, sme
);
1417 cfg80211_put_bss(bss
);
1418 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1422 int lbs_disconnect(struct lbs_private
*priv
, u16 reason
)
1424 struct cmd_ds_802_11_deauthenticate cmd
;
1427 memset(&cmd
, 0, sizeof(cmd
));
1428 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
1429 /* Mildly ugly to use a locally store my own BSSID ... */
1430 memcpy(cmd
.macaddr
, &priv
->assoc_bss
, ETH_ALEN
);
1431 cmd
.reasoncode
= cpu_to_le16(reason
);
1433 ret
= lbs_cmd_with_response(priv
, CMD_802_11_DEAUTHENTICATE
, &cmd
);
1437 cfg80211_disconnected(priv
->dev
,
1441 priv
->connect_status
= LBS_DISCONNECTED
;
1446 static int lbs_cfg_disconnect(struct wiphy
*wiphy
, struct net_device
*dev
,
1449 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1451 if (dev
== priv
->mesh_dev
)
1454 lbs_deb_enter_args(LBS_DEB_CFG80211
, "reason_code %d", reason_code
);
1456 /* store for lbs_cfg_ret_disconnect() */
1457 priv
->disassoc_reason
= reason_code
;
1459 return lbs_disconnect(priv
, reason_code
);
1462 static int lbs_cfg_set_default_key(struct wiphy
*wiphy
,
1463 struct net_device
*netdev
,
1464 u8 key_index
, bool unicast
,
1467 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1469 if (netdev
== priv
->mesh_dev
)
1472 lbs_deb_enter(LBS_DEB_CFG80211
);
1474 if (key_index
!= priv
->wep_tx_key
) {
1475 lbs_deb_assoc("set_default_key: to %d\n", key_index
);
1476 priv
->wep_tx_key
= key_index
;
1477 lbs_set_wep_keys(priv
);
1484 static int lbs_cfg_add_key(struct wiphy
*wiphy
, struct net_device
*netdev
,
1485 u8 idx
, bool pairwise
, const u8
*mac_addr
,
1486 struct key_params
*params
)
1488 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1493 if (netdev
== priv
->mesh_dev
)
1496 lbs_deb_enter(LBS_DEB_CFG80211
);
1498 lbs_deb_assoc("add_key: cipher 0x%x, mac_addr %pM\n",
1499 params
->cipher
, mac_addr
);
1500 lbs_deb_assoc("add_key: key index %d, key len %d\n",
1501 idx
, params
->key_len
);
1502 if (params
->key_len
)
1503 lbs_deb_hex(LBS_DEB_CFG80211
, "KEY",
1504 params
->key
, params
->key_len
);
1506 lbs_deb_assoc("add_key: seq len %d\n", params
->seq_len
);
1507 if (params
->seq_len
)
1508 lbs_deb_hex(LBS_DEB_CFG80211
, "SEQ",
1509 params
->seq
, params
->seq_len
);
1511 switch (params
->cipher
) {
1512 case WLAN_CIPHER_SUITE_WEP40
:
1513 case WLAN_CIPHER_SUITE_WEP104
:
1514 /* actually compare if something has changed ... */
1515 if ((priv
->wep_key_len
[idx
] != params
->key_len
) ||
1516 memcmp(priv
->wep_key
[idx
],
1517 params
->key
, params
->key_len
) != 0) {
1518 priv
->wep_key_len
[idx
] = params
->key_len
;
1519 memcpy(priv
->wep_key
[idx
],
1520 params
->key
, params
->key_len
);
1521 lbs_set_wep_keys(priv
);
1524 case WLAN_CIPHER_SUITE_TKIP
:
1525 case WLAN_CIPHER_SUITE_CCMP
:
1526 key_info
= KEY_INFO_WPA_ENABLED
| ((idx
== 0)
1527 ? KEY_INFO_WPA_UNICAST
1528 : KEY_INFO_WPA_MCAST
);
1529 key_type
= (params
->cipher
== WLAN_CIPHER_SUITE_TKIP
)
1532 lbs_set_key_material(priv
,
1535 params
->key
, params
->key_len
);
1538 wiphy_err(wiphy
, "unhandled cipher 0x%x\n", params
->cipher
);
1547 static int lbs_cfg_del_key(struct wiphy
*wiphy
, struct net_device
*netdev
,
1548 u8 key_index
, bool pairwise
, const u8
*mac_addr
)
1551 lbs_deb_enter(LBS_DEB_CFG80211
);
1553 lbs_deb_assoc("del_key: key_idx %d, mac_addr %pM\n",
1554 key_index
, mac_addr
);
1557 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1559 * I think can keep this a NO-OP, because:
1561 * - we clear all keys whenever we do lbs_cfg_connect() anyway
1562 * - neither "iw" nor "wpa_supplicant" won't call this during
1563 * an ongoing connection
1564 * - TODO: but I have to check if this is still true when
1565 * I set the AP to periodic re-keying
1566 * - we've not kzallec() something when we've added a key at
1567 * lbs_cfg_connect() or lbs_cfg_add_key().
1569 * This causes lbs_cfg_del_key() only called at disconnect time,
1570 * where we'd just waste time deleting a key that is not going
1571 * to be used anyway.
1573 if (key_index
< 3 && priv
->wep_key_len
[key_index
]) {
1574 priv
->wep_key_len
[key_index
] = 0;
1575 lbs_set_wep_keys(priv
);
1587 static int lbs_cfg_get_station(struct wiphy
*wiphy
, struct net_device
*dev
,
1588 u8
*mac
, struct station_info
*sinfo
)
1590 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1595 lbs_deb_enter(LBS_DEB_CFG80211
);
1597 sinfo
->filled
|= STATION_INFO_TX_BYTES
|
1598 STATION_INFO_TX_PACKETS
|
1599 STATION_INFO_RX_BYTES
|
1600 STATION_INFO_RX_PACKETS
;
1601 sinfo
->tx_bytes
= priv
->dev
->stats
.tx_bytes
;
1602 sinfo
->tx_packets
= priv
->dev
->stats
.tx_packets
;
1603 sinfo
->rx_bytes
= priv
->dev
->stats
.rx_bytes
;
1604 sinfo
->rx_packets
= priv
->dev
->stats
.rx_packets
;
1606 /* Get current RSSI */
1607 ret
= lbs_get_rssi(priv
, &signal
, &noise
);
1609 sinfo
->signal
= signal
;
1610 sinfo
->filled
|= STATION_INFO_SIGNAL
;
1613 /* Convert priv->cur_rate from hw_value to NL80211 value */
1614 for (i
= 0; i
< ARRAY_SIZE(lbs_rates
); i
++) {
1615 if (priv
->cur_rate
== lbs_rates
[i
].hw_value
) {
1616 sinfo
->txrate
.legacy
= lbs_rates
[i
].bitrate
;
1617 sinfo
->filled
|= STATION_INFO_TX_BITRATE
;
1629 * "Site survey", here just current channel and noise level
1632 static int lbs_get_survey(struct wiphy
*wiphy
, struct net_device
*dev
,
1633 int idx
, struct survey_info
*survey
)
1635 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1639 if (dev
== priv
->mesh_dev
)
1645 lbs_deb_enter(LBS_DEB_CFG80211
);
1647 survey
->channel
= ieee80211_get_channel(wiphy
,
1648 ieee80211_channel_to_frequency(priv
->channel
,
1649 IEEE80211_BAND_2GHZ
));
1651 ret
= lbs_get_rssi(priv
, &signal
, &noise
);
1653 survey
->filled
= SURVEY_INFO_NOISE_DBM
;
1654 survey
->noise
= noise
;
1657 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1668 static int lbs_change_intf(struct wiphy
*wiphy
, struct net_device
*dev
,
1669 enum nl80211_iftype type
, u32
*flags
,
1670 struct vif_params
*params
)
1672 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1675 if (dev
== priv
->mesh_dev
)
1679 case NL80211_IFTYPE_MONITOR
:
1680 case NL80211_IFTYPE_STATION
:
1681 case NL80211_IFTYPE_ADHOC
:
1687 lbs_deb_enter(LBS_DEB_CFG80211
);
1689 if (priv
->iface_running
)
1690 ret
= lbs_set_iface_type(priv
, type
);
1693 priv
->wdev
->iftype
= type
;
1695 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1706 * The firmware needs the following bits masked out of the beacon-derived
1707 * capability field when associating/joining to a BSS:
1708 * 9 (QoS), 11 (APSD), 12 (unused), 14 (unused), 15 (unused)
1710 #define CAPINFO_MASK (~(0xda00))
1713 static void lbs_join_post(struct lbs_private
*priv
,
1714 struct cfg80211_ibss_params
*params
,
1715 u8
*bssid
, u16 capability
)
1717 u8 fake_ie
[2 + IEEE80211_MAX_SSID_LEN
+ /* ssid */
1718 2 + 4 + /* basic rates */
1719 2 + 1 + /* DS parameter */
1721 2 + 8]; /* extended rates */
1724 lbs_deb_enter(LBS_DEB_CFG80211
);
1727 * For cfg80211_inform_bss, we'll need a fake IE, as we can't get
1728 * the real IE from the firmware. So we fabricate a fake IE based on
1729 * what the firmware actually sends (sniffed with wireshark).
1732 *fake
++ = WLAN_EID_SSID
;
1733 *fake
++ = params
->ssid_len
;
1734 memcpy(fake
, params
->ssid
, params
->ssid_len
);
1735 fake
+= params
->ssid_len
;
1736 /* Fake supported basic rates IE */
1737 *fake
++ = WLAN_EID_SUPP_RATES
;
1743 /* Fake DS channel IE */
1744 *fake
++ = WLAN_EID_DS_PARAMS
;
1746 *fake
++ = params
->channel
->hw_value
;
1747 /* Fake IBSS params IE */
1748 *fake
++ = WLAN_EID_IBSS_PARAMS
;
1750 *fake
++ = 0; /* ATIM=0 */
1752 /* Fake extended rates IE, TODO: don't add this for 802.11b only,
1753 * but I don't know how this could be checked */
1754 *fake
++ = WLAN_EID_EXT_SUPP_RATES
;
1764 lbs_deb_hex(LBS_DEB_CFG80211
, "IE", fake_ie
, fake
- fake_ie
);
1766 cfg80211_inform_bss(priv
->wdev
->wiphy
,
1771 params
->beacon_interval
,
1772 fake_ie
, fake
- fake_ie
,
1775 memcpy(priv
->wdev
->ssid
, params
->ssid
, params
->ssid_len
);
1776 priv
->wdev
->ssid_len
= params
->ssid_len
;
1778 cfg80211_ibss_joined(priv
->dev
, bssid
, GFP_KERNEL
);
1780 /* TODO: consider doing this at MACREG_INT_CODE_LINK_SENSED time */
1781 priv
->connect_status
= LBS_CONNECTED
;
1782 netif_carrier_on(priv
->dev
);
1783 if (!priv
->tx_pending_len
)
1784 netif_wake_queue(priv
->dev
);
1786 lbs_deb_leave(LBS_DEB_CFG80211
);
1789 static int lbs_ibss_join_existing(struct lbs_private
*priv
,
1790 struct cfg80211_ibss_params
*params
,
1791 struct cfg80211_bss
*bss
)
1793 const u8
*rates_eid
= ieee80211_bss_get_ie(bss
, WLAN_EID_SUPP_RATES
);
1794 struct cmd_ds_802_11_ad_hoc_join cmd
;
1795 u8 preamble
= RADIO_PREAMBLE_SHORT
;
1798 lbs_deb_enter(LBS_DEB_CFG80211
);
1800 /* TODO: set preamble based on scan result */
1801 ret
= lbs_set_radio(priv
, preamble
, 1);
1806 * Example CMD_802_11_AD_HOC_JOIN command:
1808 * command 2c 00 CMD_802_11_AD_HOC_JOIN
1812 * bssid 02 27 27 97 2f 96
1813 * ssid 49 42 53 53 00 00 00 00
1814 * 00 00 00 00 00 00 00 00
1815 * 00 00 00 00 00 00 00 00
1816 * 00 00 00 00 00 00 00 00
1817 * type 02 CMD_BSS_TYPE_IBSS
1818 * beacon period 64 00
1820 * timestamp 00 00 00 00 00 00 00 00
1821 * localtime 00 00 00 00 00 00 00 00
1825 * reserveed 00 00 00 00
1828 * IE IBSS atim 00 00
1829 * reserved 00 00 00 00
1831 * rates 82 84 8b 96 0c 12 18 24 30 48 60 6c 00
1832 * fail timeout ff 00
1835 memset(&cmd
, 0, sizeof(cmd
));
1836 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
1838 memcpy(cmd
.bss
.bssid
, bss
->bssid
, ETH_ALEN
);
1839 memcpy(cmd
.bss
.ssid
, params
->ssid
, params
->ssid_len
);
1840 cmd
.bss
.type
= CMD_BSS_TYPE_IBSS
;
1841 cmd
.bss
.beaconperiod
= cpu_to_le16(params
->beacon_interval
);
1842 cmd
.bss
.ds
.header
.id
= WLAN_EID_DS_PARAMS
;
1843 cmd
.bss
.ds
.header
.len
= 1;
1844 cmd
.bss
.ds
.channel
= params
->channel
->hw_value
;
1845 cmd
.bss
.ibss
.header
.id
= WLAN_EID_IBSS_PARAMS
;
1846 cmd
.bss
.ibss
.header
.len
= 2;
1847 cmd
.bss
.ibss
.atimwindow
= 0;
1848 cmd
.bss
.capability
= cpu_to_le16(bss
->capability
& CAPINFO_MASK
);
1850 /* set rates to the intersection of our rates and the rates in the
1853 lbs_add_rates(cmd
.bss
.rates
);
1856 u8 rates_max
= rates_eid
[1];
1857 u8
*rates
= cmd
.bss
.rates
;
1858 for (hw
= 0; hw
< ARRAY_SIZE(lbs_rates
); hw
++) {
1859 u8 hw_rate
= lbs_rates
[hw
].bitrate
/ 5;
1860 for (i
= 0; i
< rates_max
; i
++) {
1861 if (hw_rate
== (rates_eid
[i
+2] & 0x7f)) {
1862 u8 rate
= rates_eid
[i
+2];
1863 if (rate
== 0x02 || rate
== 0x04 ||
1864 rate
== 0x0b || rate
== 0x16)
1872 /* Only v8 and below support setting this */
1873 if (MRVL_FW_MAJOR_REV(priv
->fwrelease
) <= 8) {
1874 cmd
.failtimeout
= cpu_to_le16(MRVDRV_ASSOCIATION_TIME_OUT
);
1875 cmd
.probedelay
= cpu_to_le16(CMD_SCAN_PROBE_DELAY_TIME
);
1877 ret
= lbs_cmd_with_response(priv
, CMD_802_11_AD_HOC_JOIN
, &cmd
);
1882 * This is a sample response to CMD_802_11_AD_HOC_JOIN:
1890 lbs_join_post(priv
, params
, bss
->bssid
, bss
->capability
);
1893 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1899 static int lbs_ibss_start_new(struct lbs_private
*priv
,
1900 struct cfg80211_ibss_params
*params
)
1902 struct cmd_ds_802_11_ad_hoc_start cmd
;
1903 struct cmd_ds_802_11_ad_hoc_result
*resp
=
1904 (struct cmd_ds_802_11_ad_hoc_result
*) &cmd
;
1905 u8 preamble
= RADIO_PREAMBLE_SHORT
;
1909 lbs_deb_enter(LBS_DEB_CFG80211
);
1911 ret
= lbs_set_radio(priv
, preamble
, 1);
1916 * Example CMD_802_11_AD_HOC_START command:
1918 * command 2b 00 CMD_802_11_AD_HOC_START
1922 * ssid 54 45 53 54 00 00 00 00
1923 * 00 00 00 00 00 00 00 00
1924 * 00 00 00 00 00 00 00 00
1925 * 00 00 00 00 00 00 00 00
1927 * beacon period 64 00
1931 * IE IBSS atim 00 00
1932 * reserved 00 00 00 00
1936 * reserved 00 00 00 00
1939 * rates 82 84 8b 96 (basic rates with have bit 7 set)
1940 * 0c 12 18 24 30 48 60 6c
1943 memset(&cmd
, 0, sizeof(cmd
));
1944 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
1945 memcpy(cmd
.ssid
, params
->ssid
, params
->ssid_len
);
1946 cmd
.bsstype
= CMD_BSS_TYPE_IBSS
;
1947 cmd
.beaconperiod
= cpu_to_le16(params
->beacon_interval
);
1948 cmd
.ibss
.header
.id
= WLAN_EID_IBSS_PARAMS
;
1949 cmd
.ibss
.header
.len
= 2;
1950 cmd
.ibss
.atimwindow
= 0;
1951 cmd
.ds
.header
.id
= WLAN_EID_DS_PARAMS
;
1952 cmd
.ds
.header
.len
= 1;
1953 cmd
.ds
.channel
= params
->channel
->hw_value
;
1954 /* Only v8 and below support setting probe delay */
1955 if (MRVL_FW_MAJOR_REV(priv
->fwrelease
) <= 8)
1956 cmd
.probedelay
= cpu_to_le16(CMD_SCAN_PROBE_DELAY_TIME
);
1957 /* TODO: mix in WLAN_CAPABILITY_PRIVACY */
1958 capability
= WLAN_CAPABILITY_IBSS
;
1959 cmd
.capability
= cpu_to_le16(capability
);
1960 lbs_add_rates(cmd
.rates
);
1963 ret
= lbs_cmd_with_response(priv
, CMD_802_11_AD_HOC_START
, &cmd
);
1968 * This is a sample response to CMD_802_11_AD_HOC_JOIN:
1975 * bssid 02 2b 7b 0f 86 0e
1977 lbs_join_post(priv
, params
, resp
->bssid
, capability
);
1980 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
1985 static int lbs_join_ibss(struct wiphy
*wiphy
, struct net_device
*dev
,
1986 struct cfg80211_ibss_params
*params
)
1988 struct lbs_private
*priv
= wiphy_priv(wiphy
);
1990 struct cfg80211_bss
*bss
;
1991 DECLARE_SSID_BUF(ssid_buf
);
1993 if (dev
== priv
->mesh_dev
)
1996 lbs_deb_enter(LBS_DEB_CFG80211
);
1998 if (!params
->channel
) {
2003 ret
= lbs_set_channel(priv
, params
->channel
->hw_value
);
2007 /* Search if someone is beaconing. This assumes that the
2008 * bss list is populated already */
2009 bss
= cfg80211_get_bss(wiphy
, params
->channel
, params
->bssid
,
2010 params
->ssid
, params
->ssid_len
,
2011 WLAN_CAPABILITY_IBSS
, WLAN_CAPABILITY_IBSS
);
2014 ret
= lbs_ibss_join_existing(priv
, params
, bss
);
2015 cfg80211_put_bss(bss
);
2017 ret
= lbs_ibss_start_new(priv
, params
);
2021 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
2026 static int lbs_leave_ibss(struct wiphy
*wiphy
, struct net_device
*dev
)
2028 struct lbs_private
*priv
= wiphy_priv(wiphy
);
2029 struct cmd_ds_802_11_ad_hoc_stop cmd
;
2032 if (dev
== priv
->mesh_dev
)
2035 lbs_deb_enter(LBS_DEB_CFG80211
);
2037 memset(&cmd
, 0, sizeof(cmd
));
2038 cmd
.hdr
.size
= cpu_to_le16(sizeof(cmd
));
2039 ret
= lbs_cmd_with_response(priv
, CMD_802_11_AD_HOC_STOP
, &cmd
);
2041 /* TODO: consider doing this at MACREG_INT_CODE_ADHOC_BCN_LOST time */
2042 lbs_mac_event_disconnected(priv
);
2044 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
2055 static struct cfg80211_ops lbs_cfg80211_ops
= {
2056 .set_channel
= lbs_cfg_set_channel
,
2057 .scan
= lbs_cfg_scan
,
2058 .connect
= lbs_cfg_connect
,
2059 .disconnect
= lbs_cfg_disconnect
,
2060 .add_key
= lbs_cfg_add_key
,
2061 .del_key
= lbs_cfg_del_key
,
2062 .set_default_key
= lbs_cfg_set_default_key
,
2063 .get_station
= lbs_cfg_get_station
,
2064 .dump_survey
= lbs_get_survey
,
2065 .change_virtual_intf
= lbs_change_intf
,
2066 .join_ibss
= lbs_join_ibss
,
2067 .leave_ibss
= lbs_leave_ibss
,
2072 * At this time lbs_private *priv doesn't even exist, so we just allocate
2073 * memory and don't initialize the wiphy further. This is postponed until we
2074 * can talk to the firmware and happens at registration time in
2075 * lbs_cfg_wiphy_register().
2077 struct wireless_dev
*lbs_cfg_alloc(struct device
*dev
)
2080 struct wireless_dev
*wdev
;
2082 lbs_deb_enter(LBS_DEB_CFG80211
);
2084 wdev
= kzalloc(sizeof(struct wireless_dev
), GFP_KERNEL
);
2086 dev_err(dev
, "cannot allocate wireless device\n");
2087 return ERR_PTR(-ENOMEM
);
2090 wdev
->wiphy
= wiphy_new(&lbs_cfg80211_ops
, sizeof(struct lbs_private
));
2092 dev_err(dev
, "cannot allocate wiphy\n");
2097 lbs_deb_leave(LBS_DEB_CFG80211
);
2102 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
2103 return ERR_PTR(ret
);
2107 static void lbs_cfg_set_regulatory_hint(struct lbs_private
*priv
)
2109 struct region_code_mapping
{
2114 /* Section 5.17.2 */
2115 static const struct region_code_mapping regmap
[] = {
2116 {"US ", 0x10}, /* US FCC */
2117 {"CA ", 0x20}, /* Canada */
2118 {"EU ", 0x30}, /* ETSI */
2119 {"ES ", 0x31}, /* Spain */
2120 {"FR ", 0x32}, /* France */
2121 {"JP ", 0x40}, /* Japan */
2125 lbs_deb_enter(LBS_DEB_CFG80211
);
2127 for (i
= 0; i
< ARRAY_SIZE(regmap
); i
++)
2128 if (regmap
[i
].code
== priv
->regioncode
) {
2129 regulatory_hint(priv
->wdev
->wiphy
, regmap
[i
].cn
);
2133 lbs_deb_leave(LBS_DEB_CFG80211
);
2138 * This function get's called after lbs_setup_firmware() determined the
2139 * firmware capabities. So we can setup the wiphy according to our
2140 * hardware/firmware.
2142 int lbs_cfg_register(struct lbs_private
*priv
)
2144 struct wireless_dev
*wdev
= priv
->wdev
;
2147 lbs_deb_enter(LBS_DEB_CFG80211
);
2149 wdev
->wiphy
->max_scan_ssids
= 1;
2150 wdev
->wiphy
->signal_type
= CFG80211_SIGNAL_TYPE_MBM
;
2152 wdev
->wiphy
->interface_modes
=
2153 BIT(NL80211_IFTYPE_STATION
) |
2154 BIT(NL80211_IFTYPE_ADHOC
);
2155 if (lbs_rtap_supported(priv
))
2156 wdev
->wiphy
->interface_modes
|= BIT(NL80211_IFTYPE_MONITOR
);
2157 if (lbs_mesh_activated(priv
))
2158 wdev
->wiphy
->interface_modes
|= BIT(NL80211_IFTYPE_MESH_POINT
);
2160 wdev
->wiphy
->bands
[IEEE80211_BAND_2GHZ
] = &lbs_band_2ghz
;
2163 * We could check priv->fwcapinfo && FW_CAPINFO_WPA, but I have
2164 * never seen a firmware without WPA
2166 wdev
->wiphy
->cipher_suites
= cipher_suites
;
2167 wdev
->wiphy
->n_cipher_suites
= ARRAY_SIZE(cipher_suites
);
2168 wdev
->wiphy
->reg_notifier
= lbs_reg_notifier
;
2170 ret
= wiphy_register(wdev
->wiphy
);
2172 pr_err("cannot register wiphy device\n");
2174 priv
->wiphy_registered
= true;
2176 ret
= register_netdev(priv
->dev
);
2178 pr_err("cannot register network device\n");
2180 INIT_DELAYED_WORK(&priv
->scan_work
, lbs_scan_worker
);
2182 lbs_cfg_set_regulatory_hint(priv
);
2184 lbs_deb_leave_args(LBS_DEB_CFG80211
, "ret %d", ret
);
2188 int lbs_reg_notifier(struct wiphy
*wiphy
,
2189 struct regulatory_request
*request
)
2191 struct lbs_private
*priv
= wiphy_priv(wiphy
);
2194 lbs_deb_enter_args(LBS_DEB_CFG80211
, "cfg80211 regulatory domain "
2195 "callback for domain %c%c\n", request
->alpha2
[0],
2196 request
->alpha2
[1]);
2198 ret
= lbs_set_11d_domain_info(priv
, request
, wiphy
->bands
);
2200 lbs_deb_leave(LBS_DEB_CFG80211
);
2204 void lbs_scan_deinit(struct lbs_private
*priv
)
2206 lbs_deb_enter(LBS_DEB_CFG80211
);
2207 cancel_delayed_work_sync(&priv
->scan_work
);
2211 void lbs_cfg_free(struct lbs_private
*priv
)
2213 struct wireless_dev
*wdev
= priv
->wdev
;
2215 lbs_deb_enter(LBS_DEB_CFG80211
);
2220 if (priv
->wiphy_registered
)
2221 wiphy_unregister(wdev
->wiphy
);
2224 wiphy_free(wdev
->wiphy
);