drivers/parisc/Kconfig

   1 menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)"
   2
   3 config GSC
   4         bool "VSC/GSC/HSC bus support"
   5         default y
   6         help
   7           The VSC, GSC and HSC busses were used from the earliest 700-series
   8           workstations up to and including the C360/J2240 workstations.  They
   9           were also used in servers from the E-class to the K-class.  They
  10           are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards.
  11           If in doubt, say "Y".
  12
  13 config HPPB
  14         bool "HP-PB bus support"
  15         depends on GSC
  16         help
  17           The HP-PB bus was used in the Nova class and K-class servers.
  18           If in doubt, say "Y"
  19
  20 config IOMMU_CCIO
  21         bool "U2/Uturn I/O MMU"
  22         depends on GSC
  23         help
  24           Say Y here to enable DMA management routines for the first
  25           generation of PA-RISC cache-coherent machines.  Programs the
  26           U2/Uturn chip in "Virtual Mode" and use the I/O MMU.
  27
  28 config GSC_LASI
  29         bool "Lasi I/O support"
  30         depends on GSC
  31         help
  32           Say Y here to support the Lasi multifunction chip found in
  33           many PA-RISC workstations & servers.  It includes interfaces
  34           for a parallel port, serial port, NCR 53c710 SCSI, Apricot
  35           Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony
  36           and floppy.  Note that you must still enable all the individual
  37           drivers for these chips.
  38
  39 config GSC_WAX
  40         bool "Wax I/O support"
  41         depends on GSC
  42         help
  43           Say Y here to support the Wax multifunction chip found in some
  44           older systems, including B/C/D/R class and 715/64, 715/80 and
  45           715/100.  Wax includes an EISA adapter, a serial port (not always
  46           used), a HIL interface chip and is also known to be used as the
  47           GSC bridge for an X.25 GSC card.
  48
  49 config EISA
  50         bool "EISA support"
  51         depends on GSC
  52         help
  53           Say Y here if you have an EISA bus in your machine.  This code
  54           supports both the Mongoose & Wax EISA adapters.  It is sadly
  55           incomplete and lacks support for card-to-host DMA.
  56
  57 source "drivers/eisa/Kconfig"
  58
  59 config ISA
  60         bool "ISA support"
  61         depends on EISA
  62         help
  63           If you want to plug an ISA card into your EISA bus, say Y here.
  64           Most people should say N.
  65
  66 config PCI
  67         bool "PCI support"
  68         help
  69           All recent HP machines have PCI slots, and you should say Y here
  70           if you have a recent machine.  If you are convinced you do not have
  71           PCI slots in your machine (eg a 712), then you may say "N" here.
  72           Beware that some GSC cards have a Dino onboard and PCI inside them,
  73           so it may be safest to say "Y" anyway.
  74
  75 source "drivers/pci/Kconfig"
  76
  77 config GSC_DINO
  78         bool "GSCtoPCI/Dino PCI support"
  79         depends on PCI && GSC
  80         help
  81           Say Y here to support the Dino & Cujo GSC to PCI bridges found in
  82           machines from the B132 to the C360, the J2240 and the A180.  Some
  83           GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on
  84           the card, and you also need to say Y here if you have such a card.
  85           Note that Dino also supplies one of the serial ports on certain
  86           machines.  If in doubt, say Y.
  87
  88 config PCI_LBA
  89         bool "LBA/Elroy PCI support"
  90         depends on PCI
  91         help
  92           Say Y here to support the Elroy PCI Lower Bus Adapter.  This is
  93           present on B, C, J, L and N-class machines with 4-digit model
  94           numbers and the A400/A500.
  95
  96 config IOSAPIC
  97         bool
  98         depends on PCI_LBA
  99         default PCI_LBA
 100
 101 config IOMMU_SBA
 102         bool
 103         depends on PCI_LBA
 104         default PCI_LBA
 105
 106 config IOMMU_HELPER
 107         bool
 108         depends on IOMMU_SBA || IOMMU_CCIO
 109         default y
 110
 111 source "drivers/pcmcia/Kconfig"
 112
 113 endmenu
 114
 115 menu "PA-RISC specific drivers"
 116
 117 config SUPERIO
 118         bool "SuperIO (SuckyIO) support"
 119         depends on PCI_LBA
 120         default y
 121         help
 122           Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and
 123           J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and
 124           Serial port on those machines.
 125
 126 config CHASSIS_LCD_LED
 127         bool "Chassis LCD and LED support"
 128         default y
 129         select VM_EVENT_COUNTERS
 130         help
 131           Say Y here if you want to enable support for the Heartbeat,
 132           Disk/Network activities LEDs on some PA-RISC machines,
 133           or support for the LCD that can be found on recent material.
 134
 135           This has nothing to do with LED State support for A and E class.
 136
 137           If unsure, say Y.
 138
 139 config PDC_CHASSIS
 140         bool "PDC chassis state codes support"
 141         default y
 142         help
 143           Say Y here if you want to enable support for Chassis codes.
 144           That includes support for LED State front panel as found on E
 145           class, and support for the GSP Virtual Front Panel (LED State and
 146           message logging)  as found on high end servers such as A, L and
 147           N-class.
 148           This driver will also display progress messages on LCD display,
 149           such as "INI", "RUN" and "FLT", and might thus clobber messages
 150           shown by the LED/LCD driver.
 151           This driver updates the state panel (LED and/or LCD) upon system
 152           state change (eg: boot, shutdown or panic).
 153
 154           If unsure, say Y.
 155
 156
 157 config PDC_CHASSIS_WARN
 158         bool "PDC chassis warnings support"
 159         depends on PROC_FS
 160         default y
 161         help
 162           Say Y here if you want to enable support for Chassis warnings.
 163           This will add a proc entry '/proc/chassis' giving some information
 164           about the overall health state of the system.
 165           This includes NVRAM battery level, overtemp or failures such as
 166           fans or power units.
 167
 168           If unsure, say Y.
 169
 170
 171 config PDC_STABLE
 172         tristate "PDC Stable Storage support"
 173         depends on SYSFS
 174         default y
 175         help
 176           Say Y here if you want to enable support for accessing Stable Storage
 177           variables (PDC non volatile variables such as Primary Boot Path,
 178           Console Path, Autoboot, Autosearch, etc) through SysFS.
 179
 180           If unsure, say Y.
 181
 182           To compile this driver as a module, choose M here.
 183           The module will be called pdc_stable.
 184
 185 endmenu