drivers/pcmcia/Kconfig

   1 #
   2 # PCCARD (PCMCIA/CardBus) bus subsystem configuration
   3 #
   4
   5 menuconfig PCCARD
   6         tristate "PCCard (PCMCIA/CardBus) support"
   7         ---help---
   8           Say Y here if you want to attach PCMCIA- or PC-cards to your Linux
   9           computer.  These are credit-card size devices such as network cards,
  10           modems or hard drives often used with laptops computers.  There are
  11           actually two varieties of these cards: 16 bit PCMCIA and 32 bit
  12           CardBus cards.
  13
  14           To compile this driver as modules, choose M here: the
  15           module will be called pcmcia_core.
  16
  17 if PCCARD
  18
  19 config PCMCIA
  20         tristate "16-bit PCMCIA support"
  21         select CRC32
  22         default y
  23         ---help---
  24            This option enables support for 16-bit PCMCIA cards. Most older
  25            PC-cards are such 16-bit PCMCIA cards, so unless you know you're
  26            only using 32-bit CardBus cards, say Y or M here.
  27
  28            To use 16-bit PCMCIA cards, you will need supporting software in
  29            most cases. (see the file <file:Documentation/Changes> for
  30            location and details).
  31
  32            To compile this driver as modules, choose M here: the
  33            module will be called pcmcia.
  34
  35            If unsure, say Y.
  36
  37 config PCMCIA_LOAD_CIS
  38         bool "Load CIS updates from userspace"
  39         depends on PCMCIA
  40         select FW_LOADER
  41         default y
  42         help
  43           Some PCMCIA cards require an updated Card Information Structure (CIS)
  44           to be loaded from userspace to work correctly. If you say Y here,
  45           and your userspace is arranged correctly, this will be loaded
  46           automatically using the in-kernel firmware loader and the hotplug
  47           subsystem, instead of relying on cardmgr from pcmcia-cs to do so.
  48
  49           If unsure, say Y.
  50
  51 config CARDBUS
  52         bool "32-bit CardBus support"
  53         depends on PCI
  54         default y
  55         ---help---
  56           CardBus is a bus mastering architecture for PC-cards, which allows
  57           for 32 bit PC-cards (the original PCMCIA standard specifies only
  58           a 16 bit wide bus). Many newer PC-cards are actually CardBus cards.
  59
  60           To use 32 bit PC-cards, you also need a CardBus compatible host
  61           bridge. Virtually all modern PCMCIA bridges do this, and most of
  62           them are "yenta-compatible", so say Y or M there, too.
  63
  64           If unsure, say Y.
  65
  66 comment "PC-card bridges"
  67
  68 config YENTA
  69         tristate "CardBus yenta-compatible bridge support"
  70         depends on PCI
  71         select CARDBUS if !EXPERT
  72         select PCCARD_NONSTATIC if PCMCIA != n && ISA
  73         select PCCARD_PCI if PCMCIA !=n && !ISA
  74         ---help---
  75           This option enables support for CardBus host bridges.  Virtually
  76           all modern PCMCIA bridges are CardBus compatible.  A "bridge" is
  77           the hardware inside your computer that PCMCIA cards are plugged
  78           into.
  79
  80           To compile this driver as modules, choose M here: the
  81           module will be called yenta_socket.
  82
  83           If unsure, say Y.
  84
  85 config YENTA_O2
  86         default y
  87         bool "Special initialization for O2Micro bridges" if EXPERT
  88         depends on YENTA
  89
  90 config YENTA_RICOH
  91         default y
  92         bool "Special initialization for Ricoh bridges" if EXPERT
  93         depends on YENTA
  94
  95 config YENTA_TI
  96         default y
  97         bool "Special initialization for TI and EnE bridges" if EXPERT
  98         depends on YENTA
  99
 100 config YENTA_ENE_TUNE
 101         default y
 102         bool "Auto-tune EnE bridges for CB cards" if EXPERT
 103         depends on YENTA_TI && CARDBUS
 104
 105 config YENTA_TOSHIBA
 106         default y
 107         bool "Special initialization for Toshiba ToPIC bridges" if EXPERT
 108         depends on YENTA
 109
 110 config PD6729
 111         tristate "Cirrus PD6729 compatible bridge support"
 112         depends on PCMCIA && PCI
 113         select PCCARD_NONSTATIC if PCMCIA != n && ISA
 114         select PCCARD_PCI if PCMCIA !=n && !ISA
 115         help
 116           This provides support for the Cirrus PD6729 PCI-to-PCMCIA bridge
 117           device, found in some older laptops and PCMCIA card readers.
 118
 119 config I82092
 120         tristate "i82092 compatible bridge support"
 121         depends on PCMCIA && PCI
 122         select PCCARD_NONSTATIC if PCMCIA != n && ISA
 123         select PCCARD_PCI if PCMCIA !=n && !ISA
 124         help
 125           This provides support for the Intel I82092AA PCI-to-PCMCIA bridge device,
 126           found in some older laptops and more commonly in evaluation boards for the
 127           chip.
 128
 129 config I82365
 130         tristate "i82365 compatible bridge support"
 131         depends on PCMCIA && ISA
 132         select PCCARD_NONSTATIC
 133         help
 134           Say Y here to include support for ISA-bus PCMCIA host bridges that
 135           are register compatible with the Intel i82365.  These are found on
 136           older laptops and ISA-bus card readers for desktop systems.  A
 137           "bridge" is the hardware inside your computer that PCMCIA cards are
 138           plugged into. If unsure, say N.
 139
 140 config TCIC
 141         tristate "Databook TCIC host bridge support"
 142         depends on PCMCIA && ISA
 143         select PCCARD_NONSTATIC
 144         help
 145           Say Y here to include support for the Databook TCIC family of PCMCIA
 146           host bridges. These are only found on a handful of old systems.
 147           "Bridge" is the name used for the hardware inside your computer that
 148           PCMCIA cards are plugged into. If unsure, say N.
 149
 150 config PCMCIA_ALCHEMY_DEVBOARD
 151         tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
 152         depends on MIPS_ALCHEMY && PCMCIA
 153         help
 154           Enable this driver of you want PCMCIA support on your Alchemy
 155           Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200, DB1300
 156           board.  NOT suitable for the PB1000!
 157
 158           This driver is also available as a module called db1xxx_ss.ko
 159
 160 config PCMCIA_XXS1500
 161         tristate "MyCable XXS1500 PCMCIA socket support"
 162         depends on PCMCIA && MIPS_XXS1500
 163         help
 164           Support for the PCMCIA/CF socket interface on MyCable XXS1500
 165           systems.
 166
 167           This driver is also available as a module called xxs1500_ss.ko
 168
 169 config PCMCIA_BCM63XX
 170         tristate "bcm63xx pcmcia support"
 171         depends on BCM63XX && PCMCIA
 172
 173 config PCMCIA_SOC_COMMON
 174         tristate
 175
 176 config PCMCIA_SA11XX_BASE
 177         tristate
 178
 179 config PCMCIA_SA1100
 180         tristate "SA1100 support"
 181         depends on ARM && ARCH_SA1100 && PCMCIA
 182         select PCMCIA_SOC_COMMON
 183         select PCMCIA_SA11XX_BASE
 184         help
 185           Say Y here to include support for SA11x0-based PCMCIA or CF
 186           sockets, found on HP iPAQs, Yopy, and other StrongARM(R)/
 187           Xscale(R) embedded machines.
 188
 189           This driver is also available as a module called sa1100_cs.
 190
 191 config PCMCIA_SA1111
 192         tristate "SA1111 support"
 193         depends on ARM && SA1111 && PCMCIA
 194         select PCMCIA_SOC_COMMON
 195         select PCMCIA_SA11XX_BASE if ARCH_SA1100
 196         select PCMCIA_PXA2XX if ARCH_LUBBOCK && SA1111
 197         help
 198           Say Y  here to include support for SA1111-based PCMCIA or CF
 199           sockets, found on the Jornada 720, Graphicsmaster and other
 200           StrongARM(R)/Xscale(R) embedded machines.
 201
 202           This driver is also available as a module called sa1111_cs.
 203
 204 config PCMCIA_PXA2XX
 205         tristate "PXA2xx support"
 206         depends on ARM && ARCH_PXA && PCMCIA
 207         depends on (ARCH_LUBBOCK || MACH_MAINSTONE || PXA_SHARPSL \
 208                     || MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \
 209                     || ARCOM_PCMCIA || ARCH_PXA_ESERIES || MACH_STARGATE2 \
 210                     || MACH_VPAC270 || MACH_BALLOON3 || MACH_COLIBRI \
 211                     || MACH_COLIBRI320 || MACH_H4700)
 212         select PCMCIA_SOC_COMMON
 213         help
 214           Say Y here to include support for the PXA2xx PCMCIA controller
 215
 216 config PCMCIA_DEBUG
 217         bool "Enable debugging"
 218         depends on (PCMCIA_SA1111 || PCMCIA_SA1100 || PCMCIA_PXA2XX)
 219         help
 220           Say Y here to enable debugging for the SoC PCMCIA layer.
 221           You will need to choose the debugging level either via the
 222           kernel command line, or module options depending whether
 223           you build the drivers as modules.
 224
 225           The kernel command line options are:
 226             sa11xx_core.pc_debug=N
 227             pxa2xx_core.pc_debug=N
 228
 229           The module option is called pc_debug=N
 230
 231           In all the above examples, N is the debugging verbosity
 232           level.
 233
 234 config PCMCIA_PROBE
 235         bool
 236         default y if ISA && !ARCH_SA1100 && !PARISC
 237
 238 config M32R_PCC
 239         bool "M32R PCMCIA I/F"
 240         depends on M32R && CHIP_M32700 && PCMCIA
 241         help
 242           Say Y here to use the M32R PCMCIA controller.
 243
 244 config M32R_CFC
 245         bool "M32R CF I/F Controller"
 246         depends on M32R && (PLAT_USRV || PLAT_M32700UT || PLAT_MAPPI2 || PLAT_MAPPI3 || PLAT_OPSPUT)
 247         help
 248           Say Y here to use the M32R CompactFlash controller.
 249
 250 config M32R_CFC_NUM
 251         int "M32R CF I/F number"
 252         depends on M32R_CFC
 253         default "1" if PLAT_USRV || PLAT_M32700UT || PLAT_MAPPI2 || PLAT_MAPPI3 || PLAT_OPSPUT
 254         help
 255           Set the number of M32R CF slots.
 256
 257 config PCMCIA_VRC4171
 258         tristate "NEC VRC4171 Card Controllers support"
 259         depends on CPU_VR41XX && ISA && PCMCIA
 260
 261 config PCMCIA_VRC4173
 262         tristate "NEC VRC4173 CARDU support"
 263         depends on CPU_VR41XX && PCI && PCMCIA
 264
 265 config OMAP_CF
 266         tristate "OMAP CompactFlash Controller"
 267         depends on PCMCIA && ARCH_OMAP16XX
 268         help
 269           Say Y here to support the CompactFlash controller on OMAP.
 270           Note that this doesn't support "True IDE" mode.
 271
 272 config BFIN_CFPCMCIA
 273         tristate "Blackfin CompactFlash PCMCIA Driver"
 274         depends on PCMCIA && BLACKFIN
 275         help
 276           Say Y here to support the CompactFlash PCMCIA driver for Blackfin.
 277
 278
 279 config AT91_CF
 280         tristate "AT91 CompactFlash Controller"
 281         depends on PCMCIA && ARCH_AT91
 282         help
 283           Say Y here to support the CompactFlash controller on AT91 chips.
 284           Or choose M to compile the driver as a module named "at91_cf".
 285
 286 config ELECTRA_CF
 287         tristate "Electra CompactFlash Controller"
 288         depends on PCMCIA && PPC_PASEMI
 289         help
 290           Say Y here to support the CompactFlash controller on the
 291           PA Semi Electra eval board.
 292
 293 config PCCARD_PCI
 294         bool
 295
 296 config PCCARD_NONSTATIC
 297         bool
 298
 299 config PCCARD_IODYN
 300         bool
 301
 302 endif   # PCCARD