drivers/pinctrl/aspeed/pinctrl-aspeed.h

   1 /*
   2  * Copyright (C) 2016 IBM Corp.
   3  *
   4  * This program is free software; you can redistribute it and/or modify
   5  * it under the terms of the GNU General Public License as published by
   6  * the Free Software Foundation; either version 2 of the License, or
   7  * (at your option) any later version.
   8  */
   9
  10 #ifndef PINCTRL_ASPEED
  11 #define PINCTRL_ASPEED
  12
  13 #include <linux/pinctrl/pinctrl.h>
  14 #include <linux/pinctrl/pinmux.h>
  15 #include <linux/pinctrl/pinconf.h>
  16 #include <linux/pinctrl/pinconf-generic.h>
  17 #include <linux/regmap.h>
  18
  19 /*
  20  * The ASPEED SoCs provide typically more than 200 pins for GPIO and other
  21  * functions. The SoC function enabled on a pin is determined on a priority
  22  * basis where a given pin can provide a number of different signal types.
  23  *
  24  * The signal active on a pin is described by both a priority level and
  25  * compound logical expressions involving multiple operators, registers and
  26  * bits. Some difficulty arises as the pin's function bit masks for each
  27  * priority level are frequently not the same (i.e. cannot just flip a bit to
  28  * change from a high to low priority signal), or even in the same register.
  29  * Further, not all signals can be unmuxed, as some expressions depend on
  30  * values in the hardware strapping register (which is treated as read-only).
  31  *
  32  * SoC Multi-function Pin Expression Examples
  33  * ------------------------------------------
  34  *
  35  * Here are some sample mux configurations from the AST2400 and AST2500
  36  * datasheets to illustrate the corner cases, roughly in order of least to most
  37  * corner. The signal priorities are in decending order from P0 (highest).
  38  *
  39  * D6 is a pin with a single function (beside GPIO); a high priority signal
  40  * that participates in one function:
  41  *
  42  * Ball | Default | P0 Signal | P0 Expression               | P1 Signal | P1 Expression | Other
  43  * -----+---------+-----------+-----------------------------+-----------+---------------+----------
  44  *  D6    GPIOA0    MAC1LINK    SCU80[0]=1                                                GPIOA0
  45  * -----+---------+-----------+-----------------------------+-----------+---------------+----------
  46  *
  47  * C5 is a multi-signal pin (high and low priority signals). Here we touch
  48  * different registers for the different functions that enable each signal:
  49  *
  50  * -----+---------+-----------+-----------------------------+-----------+---------------+----------
  51  *  C5    GPIOA4    SCL9        SCU90[22]=1                   TIMER5      SCU80[4]=1      GPIOA4
  52  * -----+---------+-----------+-----------------------------+-----------+---------------+----------
  53  *
  54  * E19 is a single-signal pin with two functions that influence the active
  55  * signal. In this case both bits have the same meaning - enable a dedicated
  56  * LPC reset pin. However it's not always the case that the bits in the
  57  * OR-relationship have the same meaning.
  58  *
  59  * -----+---------+-----------+-----------------------------+-----------+---------------+----------
  60  *  E19   GPIOB4    LPCRST#     SCU80[12]=1 | Strap[14]=1                                 GPIOB4
  61  * -----+---------+-----------+-----------------------------+-----------+---------------+----------
  62  *
  63  * For example, pin B19 has a low-priority signal that's enabled by two
  64  * distinct SoC functions: A specific SIOPBI bit in register SCUA4, and an ACPI
  65  * bit in the STRAP register. The ACPI bit configures signals on pins in
  66  * addition to B19. Both of the low priority functions as well as the high
  67  * priority function must be disabled for GPIOF1 to be used.
  68  *
  69  * Ball | Default | P0 Signal | P0 Expression                           | P1 Signal | P1 Expression                          | Other
  70  * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
  71  *  B19   GPIOF1    NDCD4       SCU80[25]=1                               SIOPBI#     SCUA4[12]=1 | Strap[19]=0                GPIOF1
  72  * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
  73  *
  74  * For pin E18, the SoC ANDs the expected state of three bits to determine the
  75  * pin's active signal:
  76  *
  77  * * SCU3C[3]: Enable external SOC reset function
  78  * * SCU80[15]: Enable SPICS1# or EXTRST# function pin
  79  * * SCU90[31]: Select SPI interface CS# output
  80  *
  81  * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
  82  *  E18   GPIOB7    EXTRST#     SCU3C[3]=1 & SCU80[15]=1 & SCU90[31]=0    SPICS1#     SCU3C[3]=1 & SCU80[15]=1 & SCU90[31]=1   GPIOB7
  83  * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+----------
  84  *
  85  * (Bits SCU3C[3] and SCU80[15] appear to only be used in the expressions for
  86  * selecting the signals on pin E18)
  87  *
  88  * Pin T5 is a multi-signal pin with a more complex configuration:
  89  *
  90  * Ball | Default | P0 Signal | P0 Expression                | P1 Signal | P1 Expression | Other
  91  * -----+---------+-----------+------------------------------+-----------+---------------+----------
  92  *  T5    GPIOL1    VPIDE       SCU90[5:4]!=0 & SCU84[17]=1    NDCD1       SCU84[17]=1     GPIOL1
  93  * -----+---------+-----------+------------------------------+-----------+---------------+----------
  94  *
  95  * The high priority signal configuration is best thought of in terms of its
  96  * exploded form, with reference to the SCU90[5:4] bits:
  97  *
  98  * * SCU90[5:4]=00: disable
  99  * * SCU90[5:4]=01: 18 bits (R6/G6/B6) video mode.
 100  * * SCU90[5:4]=10: 24 bits (R8/G8/B8) video mode.
 101  * * SCU90[5:4]=11: 30 bits (R10/G10/B10) video mode.
 102  *
 103  * Re-writing:
 104  *
 105  * -----+---------+-----------+------------------------------+-----------+---------------+----------
 106  *  T5    GPIOL1    VPIDE      (SCU90[5:4]=1 & SCU84[17]=1)    NDCD1       SCU84[17]=1     GPIOL1
 107  *                             | (SCU90[5:4]=2 & SCU84[17]=1)
 108  *                             | (SCU90[5:4]=3 & SCU84[17]=1)
 109  * -----+---------+-----------+------------------------------+-----------+---------------+----------
 110  *
 111  * For reference the SCU84[17] bit configure the "UART1 NDCD1 or Video VPIDE
 112  * function pin", where the signal itself is determined by whether SCU94[5:4]
 113  * is disabled or in one of the 18, 24 or 30bit video modes.
 114  *
 115  * Other video-input-related pins require an explicit state in SCU90[5:4], e.g.
 116  * W1 and U5:
 117  *
 118  * -----+---------+-----------+------------------------------+-----------+---------------+----------
 119  *  W1    GPIOL6    VPIB0       SCU90[5:4]=3 & SCU84[22]=1     TXD1        SCU84[22]=1     GPIOL6
 120  *  U5    GPIOL7    VPIB1       SCU90[5:4]=3 & SCU84[23]=1     RXD1        SCU84[23]=1     GPIOL7
 121  * -----+---------+-----------+------------------------------+-----------+---------------+----------
 122  *
 123  * The examples of T5 and W1 are particularly fertile, as they also demonstrate
 124  * that despite operating as part of the video input bus each signal needs to
 125  * be enabled individually via it's own SCU84 (in the cases of T5 and W1)
 126  * register bit. This is a little crazy if the bus doesn't have optional
 127  * signals, but is used to decent effect with some of the UARTs where not all
 128  * signals are required. However, this isn't done consistently - UART1 is
 129  * enabled on a per-pin basis, and by contrast, all signals for UART6 are
 130  * enabled by a single bit.
 131  *
 132  * Further, the high and low priority signals listed in the table above share
 133  * a configuration bit. The VPI signals should operate in concert in a single
 134  * function, but the UART signals should retain the ability to be configured
 135  * independently. This pushes the implementation down the path of tagging a
 136  * signal's expressions with the function they participate in, rather than
 137  * defining masks affecting multiple signals per function. The latter approach
 138  * fails in this instance where applying the configuration for the UART pin of
 139  * interest will stomp on the state of other UART signals when disabling the
 140  * VPI functions on the current pin.
 141  *
 142  * Ball |  Default   | P0 Signal | P0 Expression             | P1 Signal | P1 Expression | Other
 143  * -----+------------+-----------+---------------------------+-----------+---------------+------------
 144  *  A12   RGMII1TXCK   GPIOT0      SCUA0[0]=1                  RMII1TXEN   Strap[6]=0      RGMII1TXCK
 145  *  B12   RGMII1TXCTL  GPIOT1      SCUA0[1]=1                  –           Strap[6]=0      RGMII1TXCTL
 146  * -----+------------+-----------+---------------------------+-----------+---------------+------------
 147  *
 148  * A12 demonstrates that the "Other" signal isn't always GPIO - in this case
 149  * GPIOT0 is a high-priority signal and RGMII1TXCK is Other. Thus, GPIO
 150  * should be treated like any other signal type with full function expression
 151  * requirements, and not assumed to be the default case. Separately, GPIOT0 and
 152  * GPIOT1's signal descriptor bits are distinct, therefore we must iterate all
 153  * pins in the function's group to disable the higher-priority signals such
 154  * that the signal for the function of interest is correctly enabled.
 155  *
 156  * Finally, three priority levels aren't always enough; the AST2500 brings with
 157  * it 18 pins of five priority levels, however the 18 pins only use three of
 158  * the five priority levels.
 159  *
 160  * Ultimately the requirement to control pins in the examples above drive the
 161  * design:
 162  *
 163  * * Pins provide signals according to functions activated in the mux
 164  *   configuration
 165  *
 166  * * Pins provide up to five signal types in a priority order
 167  *
 168  * * For priorities levels defined on a pin, each priority provides one signal
 169  *
 170  * * Enabling lower priority signals requires higher priority signals be
 171  *   disabled
 172  *
 173  * * A function represents a set of signals; functions are distinct if their
 174  *   sets of signals are not equal
 175  *
 176  * * Signals participate in one or more functions
 177  *
 178  * * A function is described by an expression of one or more signal
 179  *   descriptors, which compare bit values in a register
 180  *
 181  * * A signal expression is the smallest set of signal descriptors whose
 182  *   comparisons must evaluate 'true' for a signal to be enabled on a pin.
 183  *
 184  * * A function's signal is active on a pin if evaluating all signal
 185  *   descriptors in the pin's signal expression for the function yields a 'true'
 186  *   result
 187  *
 188  * * A signal at a given priority on a given pin is active if any of the
 189  *   functions in which the signal participates are active, and no higher
 190  *   priority signal on the pin is active
 191  *
 192  * * GPIO is configured per-pin
 193  *
 194  * And so:
 195  *
 196  * * To disable a signal, any function(s) activating the signal must be
 197  *   disabled
 198  *
 199  * * Each pin must know the signal expressions of functions in which it
 200  *   participates, for the purpose of enabling the Other function. This is done
 201  *   by deactivating all functions that activate higher priority signals on the
 202  *   pin.
 203  *
 204  * As a concrete example:
 205  *
 206  * * T5 provides three signals types: VPIDE, NDCD1 and GPIO
 207  *
 208  * * The VPIDE signal participates in 3 functions: VPI18, VPI24 and VPI30
 209  *
 210  * * The NDCD1 signal participates in just its own NDCD1 function
 211  *
 212  * * VPIDE is high priority, NDCD1 is low priority, and GPIOL1 is the least
 213  *   prioritised
 214  *
 215  * * The prerequisit for activating the NDCD1 signal is that the VPI18, VPI24
 216  *   and VPI30 functions all be disabled
 217  *
 218  * * Similarly, all of VPI18, VPI24, VPI30 and NDCD1 functions must be disabled
 219  *   to provide GPIOL6
 220  *
 221  * Considerations
 222  * --------------
 223  *
 224  * If pinctrl allows us to allocate a pin we can configure a function without
 225  * concern for the function of already allocated pins, if pin groups are
 226  * created with respect to the SoC functions in which they participate. This is
 227  * intuitive, but it did not feel obvious from the bit/pin relationships.
 228  *
 229  * Conversely, failing to allocate all pins in a group indicates some bits (as
 230  * well as pins) required for the group's configuration will already be in use,
 231  * likely in a way that's inconsistent with the requirements of the failed
 232  * group.
 233  */
 234
 235 /*
 236  * The "Multi-function Pins Mapping and Control" table in the SoC datasheet
 237  * references registers by the device/offset mnemonic. The register macros
 238  * below are named the same way to ease transcription and verification (as
 239  * opposed to naming them e.g. PINMUX_CTRL_[0-9]). Further, signal expressions
 240  * reference registers beyond those dedicated to pinmux, such as the system
 241  * reset control and MAC clock configuration registers. The AST2500 goes a step
 242  * further and references registers in the graphics IP block, but that isn't
 243  * handled yet.
 244  */
 245 #define SCU2C           0x2C /* Misc. Control Register */
 246 #define SCU3C           0x3C /* System Reset Control/Status Register */
 247 #define SCU48           0x48 /* MAC Interface Clock Delay Setting */
 248 #define HW_STRAP1       0x70 /* AST2400 strapping is 33 bits, is split */
 249 #define SCU80           0x80 /* Multi-function Pin Control #1 */
 250 #define SCU84           0x84 /* Multi-function Pin Control #2 */
 251 #define SCU88           0x88 /* Multi-function Pin Control #3 */
 252 #define SCU8C           0x8C /* Multi-function Pin Control #4 */
 253 #define SCU90           0x90 /* Multi-function Pin Control #5 */
 254 #define SCU94           0x94 /* Multi-function Pin Control #6 */
 255 #define SCUA0           0xA0 /* Multi-function Pin Control #7 */
 256 #define SCUA4           0xA4 /* Multi-function Pin Control #8 */
 257 #define SCUA8           0xA8 /* Multi-function Pin Control #9 */
 258 #define HW_STRAP2       0xD0 /* Strapping */
 259
 260  /**
 261   * A signal descriptor, which describes the register, bits and the
 262   * enable/disable values that should be compared or written.
 263   *
 264   * @reg: The register offset from base in bytes
 265   * @mask: The mask to apply to the register. The lowest set bit of the mask is
 266   *        used to derive the shift value.
 267   * @enable: The value that enables the function. Value should be in the LSBs,
 268   *          not at the position of the mask.
 269   * @disable: The value that disables the function. Value should be in the
 270   *           LSBs, not at the position of the mask.
 271   */
 272 struct aspeed_sig_desc {
 273         unsigned int reg;
 274         u32 mask;
 275         u32 enable;
 276         u32 disable;
 277 };
 278
 279 /**
 280  * Describes a signal expression. The expression is evaluated by ANDing the
 281  * evaluation of the descriptors.
 282  *
 283  * @signal: The signal name for the priority level on the pin. If the signal
 284  *          type is GPIO, then the signal name must begin with the string
 285  *          "GPIO", e.g. GPIOA0, GPIOT4 etc.
 286  * @function: The name of the function the signal participates in for the
 287  *            associated expression
 288  * @ndescs: The number of signal descriptors in the expression
 289  * @descs: Pointer to an array of signal descriptors that comprise the
 290  *         function expression
 291  */
 292 struct aspeed_sig_expr {
 293         const char *signal;
 294         const char *function;
 295         int ndescs;
 296         const struct aspeed_sig_desc *descs;
 297 };
 298
 299 /**
 300  * A struct capturing the list of expressions enabling signals at each priority
 301  * for a given pin. The signal configuration for a priority level is evaluated
 302  * by ORing the evaluation of the signal expressions in the respective
 303  * priority's list.
 304  *
 305  * @name: A name for the pin
 306  * @prios: A pointer to an array of expression list pointers
 307  *
 308  */
 309 struct aspeed_pin_desc {
 310         const char *name;
 311         const struct aspeed_sig_expr ***prios;
 312 };
 313
 314 /* Macro hell */
 315
 316 /**
 317  * Short-hand macro for describing a configuration enabled by the state of one
 318  * bit. The disable value is derived.
 319  *
 320  * @reg: The signal's associated register, offset from base
 321  * @idx: The signal's bit index in the register
 322  * @val: The value (0 or 1) that enables the function
 323  */
 324 #define SIG_DESC_BIT(reg, idx, val) \
 325         { reg, BIT_MASK(idx), val, (((val) + 1) & 1) }
 326
 327 /**
 328  * A further short-hand macro describing a configuration enabled with a set bit.
 329  *
 330  * @reg: The configuration's associated register, offset from base
 331  * @idx: The configuration's bit index in the register
 332  */
 333 #define SIG_DESC_SET(reg, idx) SIG_DESC_BIT(reg, idx, 1)
 334
 335 #define SIG_DESC_LIST_SYM(sig, func) sig_descs_ ## sig ## _ ## func
 336 #define SIG_DESC_LIST_DECL(sig, func, ...) \
 337         static const struct aspeed_sig_desc SIG_DESC_LIST_SYM(sig, func)[] = \
 338                 { __VA_ARGS__ }
 339
 340 #define SIG_EXPR_SYM(sig, func) sig_expr_ ## sig ## _ ## func
 341 #define SIG_EXPR_DECL_(sig, func) \
 342         static const struct aspeed_sig_expr SIG_EXPR_SYM(sig, func) = \
 343         { \
 344                 .signal = #sig, \
 345                 .function = #func, \
 346                 .ndescs = ARRAY_SIZE(SIG_DESC_LIST_SYM(sig, func)), \
 347                 .descs = &(SIG_DESC_LIST_SYM(sig, func))[0], \
 348         }
 349
 350 /**
 351  * Declare a signal expression.
 352  *
 353  * @sig: A macro symbol name for the signal (is subjected to stringification
 354  *        and token pasting)
 355  * @func: The function in which the signal is participating
 356  * @...: Signal descriptors that define the signal expression
 357  *
 358  * For example, the following declares the ROMD8 signal for the ROM16 function:
 359  *
 360  *     SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6));
 361  *
 362  * And with multiple signal descriptors:
 363  *
 364  *     SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4),
 365  *              { HW_STRAP1, GENMASK(1, 0), 0, 0 });
 366  */
 367 #define SIG_EXPR_DECL(sig, func, ...) \
 368         SIG_DESC_LIST_DECL(sig, func, __VA_ARGS__); \
 369         SIG_EXPR_DECL_(sig, func)
 370
 371 /**
 372  * Declare a pointer to a signal expression
 373  *
 374  * @sig: The macro symbol name for the signal (subjected to token pasting)
 375  * @func: The macro symbol name for the function (subjected to token pasting)
 376  */
 377 #define SIG_EXPR_PTR(sig, func) (&SIG_EXPR_SYM(sig, func))
 378
 379 #define SIG_EXPR_LIST_SYM(sig) sig_exprs_ ## sig
 380
 381 /**
 382  * Declare a signal expression list for reference in a struct aspeed_pin_prio.
 383  *
 384  * @sig: A macro symbol name for the signal (is subjected to token pasting)
 385  * @...: Signal expression structure pointers (use SIG_EXPR_PTR())
 386  *
 387  * For example, the 16-bit ROM bus can be enabled by one of two possible signal
 388  * expressions:
 389  *
 390  *     SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6));
 391  *     SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4),
 392  *              { HW_STRAP1, GENMASK(1, 0), 0, 0 });
 393  *     SIG_EXPR_LIST_DECL(ROMD8, SIG_EXPR_PTR(ROMD8, ROM16),
 394  *              SIG_EXPR_PTR(ROMD8, ROM16S));
 395  */
 396 #define SIG_EXPR_LIST_DECL(sig, ...) \
 397         static const struct aspeed_sig_expr *SIG_EXPR_LIST_SYM(sig)[] = \
 398                 { __VA_ARGS__, NULL }
 399
 400 /**
 401  * A short-hand macro for declaring a function expression and an expression
 402  * list with a single function.
 403  *
 404  * @func: A macro symbol name for the function (is subjected to token pasting)
 405  * @...: Function descriptors that define the function expression
 406  *
 407  * For example, signal NCTS6 participates in its own function with one group:
 408  *
 409  *     SIG_EXPR_LIST_DECL_SINGLE(NCTS6, NCTS6, SIG_DESC_SET(SCU90, 7));
 410  */
 411 #define SIG_EXPR_LIST_DECL_SINGLE(sig, func, ...) \
 412         SIG_DESC_LIST_DECL(sig, func, __VA_ARGS__); \
 413         SIG_EXPR_DECL_(sig, func); \
 414         SIG_EXPR_LIST_DECL(sig, SIG_EXPR_PTR(sig, func))
 415
 416 #define SIG_EXPR_LIST_DECL_DUAL(sig, f0, f1) \
 417         SIG_EXPR_LIST_DECL(sig, SIG_EXPR_PTR(sig, f0), SIG_EXPR_PTR(sig, f1))
 418
 419 #define SIG_EXPR_LIST_PTR(sig) (&SIG_EXPR_LIST_SYM(sig)[0])
 420
 421 #define PIN_EXPRS_SYM(pin) pin_exprs_ ## pin
 422 #define PIN_EXPRS_PTR(pin) (&PIN_EXPRS_SYM(pin)[0])
 423 #define PIN_SYM(pin) pin_ ## pin
 424
 425 #define MS_PIN_DECL_(pin, ...) \
 426         static const struct aspeed_sig_expr **PIN_EXPRS_SYM(pin)[] = \
 427                 { __VA_ARGS__, NULL }; \
 428         static const struct aspeed_pin_desc PIN_SYM(pin) = \
 429                 { #pin, PIN_EXPRS_PTR(pin) }
 430
 431 /**
 432  * Declare a multi-signal pin
 433  *
 434  * @pin: The pin number
 435  * @other: Macro name for "other" functionality (subjected to stringification)
 436  * @high: Macro name for the highest priority signal functions
 437  * @low: Macro name for the low signal functions
 438  *
 439  * For example:
 440  *
 441  *     #define A8 56
 442  *     SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6));
 443  *     SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4),
 444  *              { HW_STRAP1, GENMASK(1, 0), 0, 0 });
 445  *     SIG_EXPR_LIST_DECL(ROMD8, SIG_EXPR_PTR(ROMD8, ROM16),
 446  *              SIG_EXPR_PTR(ROMD8, ROM16S));
 447  *     SIG_EXPR_LIST_DECL_SINGLE(NCTS6, NCTS6, SIG_DESC_SET(SCU90, 7));
 448  *     MS_PIN_DECL(A8, GPIOH0, ROMD8, NCTS6);
 449  */
 450 #define MS_PIN_DECL(pin, other, high, low) \
 451         SIG_EXPR_LIST_DECL_SINGLE(other, other); \
 452         MS_PIN_DECL_(pin, \
 453                         SIG_EXPR_LIST_PTR(high), \
 454                         SIG_EXPR_LIST_PTR(low), \
 455                         SIG_EXPR_LIST_PTR(other))
 456
 457 #define PIN_GROUP_SYM(func) pins_ ## func
 458 #define FUNC_GROUP_SYM(func) groups_ ## func
 459 #define FUNC_GROUP_DECL(func, ...) \
 460         static const int PIN_GROUP_SYM(func)[] = { __VA_ARGS__ }; \
 461         static const char *FUNC_GROUP_SYM(func)[] = { #func }
 462
 463 /**
 464  * Declare a single signal pin
 465  *
 466  * @pin: The pin number
 467  * @other: Macro name for "other" functionality (subjected to stringification)
 468  * @sig: Macro name for the signal (subjected to stringification)
 469  *
 470  * For example:
 471  *
 472  *     #define E3 80
 473  *     SIG_EXPR_LIST_DECL_SINGLE(SCL5, I2C5, I2C5_DESC);
 474  *     SS_PIN_DECL(E3, GPIOK0, SCL5);
 475  */
 476 #define SS_PIN_DECL(pin, other, sig) \
 477         SIG_EXPR_LIST_DECL_SINGLE(other, other); \
 478         MS_PIN_DECL_(pin, SIG_EXPR_LIST_PTR(sig), SIG_EXPR_LIST_PTR(other))
 479
 480 /**
 481  * Single signal, single function pin declaration
 482  *
 483  * @pin: The pin number
 484  * @other: Macro name for "other" functionality (subjected to stringification)
 485  * @sig: Macro name for the signal (subjected to stringification)
 486  * @...: Signal descriptors that define the function expression
 487  *
 488  * For example:
 489  *
 490  *    SSSF_PIN_DECL(A4, GPIOA2, TIMER3, SIG_DESC_SET(SCU80, 2));
 491  */
 492 #define SSSF_PIN_DECL(pin, other, sig, ...) \
 493         SIG_EXPR_LIST_DECL_SINGLE(sig, sig, __VA_ARGS__); \
 494         SIG_EXPR_LIST_DECL_SINGLE(other, other); \
 495         MS_PIN_DECL_(pin, SIG_EXPR_LIST_PTR(sig), SIG_EXPR_LIST_PTR(other)); \
 496         FUNC_GROUP_DECL(sig, pin)
 497
 498 #define GPIO_PIN_DECL(pin, gpio) \
 499         SIG_EXPR_LIST_DECL_SINGLE(gpio, gpio); \
 500         MS_PIN_DECL_(pin, SIG_EXPR_LIST_PTR(gpio))
 501
 502 struct aspeed_pinctrl_data {
 503         struct regmap *map;
 504
 505         const struct pinctrl_pin_desc *pins;
 506         const unsigned int npins;
 507
 508         const struct aspeed_pin_group *groups;
 509         const unsigned int ngroups;
 510
 511         const struct aspeed_pin_function *functions;
 512         const unsigned int nfunctions;
 513 };
 514
 515 #define ASPEED_PINCTRL_PIN(name_) \
 516         [name_] = { \
 517                 .number = name_, \
 518                 .name = #name_, \
 519                 .drv_data = (void *) &(PIN_SYM(name_)) \
 520         }
 521
 522 struct aspeed_pin_group {
 523         const char *name;
 524         const unsigned int *pins;
 525         const unsigned int npins;
 526 };
 527
 528 #define ASPEED_PINCTRL_GROUP(name_) { \
 529         .name = #name_, \
 530         .pins = &(PIN_GROUP_SYM(name_))[0], \
 531         .npins = ARRAY_SIZE(PIN_GROUP_SYM(name_)), \
 532 }
 533
 534 struct aspeed_pin_function {
 535         const char *name;
 536         const char *const *groups;
 537         unsigned int ngroups;
 538 };
 539
 540 #define ASPEED_PINCTRL_FUNC(name_, ...) { \
 541         .name = #name_, \
 542         .groups = &FUNC_GROUP_SYM(name_)[0], \
 543         .ngroups = ARRAY_SIZE(FUNC_GROUP_SYM(name_)), \
 544 }
 545
 546 int aspeed_pinctrl_get_groups_count(struct pinctrl_dev *pctldev);
 547 const char *aspeed_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
 548                 unsigned int group);
 549 int aspeed_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
 550                 unsigned int group, const unsigned int **pins,
 551                 unsigned int *npins);
 552 void aspeed_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
 553                 struct seq_file *s, unsigned int offset);
 554 int aspeed_pinmux_get_fn_count(struct pinctrl_dev *pctldev);
 555 const char *aspeed_pinmux_get_fn_name(struct pinctrl_dev *pctldev,
 556                 unsigned int function);
 557 int aspeed_pinmux_get_fn_groups(struct pinctrl_dev *pctldev,
 558                 unsigned int function, const char * const **groups,
 559                 unsigned int * const num_groups);
 560 int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
 561                 unsigned int group);
 562 int aspeed_gpio_request_enable(struct pinctrl_dev *pctldev,
 563                 struct pinctrl_gpio_range *range,
 564                 unsigned int offset);
 565 int aspeed_pinctrl_probe(struct platform_device *pdev,
 566                 struct pinctrl_desc *pdesc,
 567                 struct aspeed_pinctrl_data *pdata);
 568
 569 #endif /* PINCTRL_ASPEED */