drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         boolean "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       boolean "SPI Master Support"
  44         boolean
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ATH79
  57         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  58         depends on ATH79 && GENERIC_GPIO
  59         select SPI_BITBANG
  60         help
  61           This enables support for the SPI controller present on the
  62           Atheros AR71XX/AR724X/AR913X SoCs.
  63
  64 config SPI_ATMEL
  65         tristate "Atmel SPI Controller"
  66         depends on (ARCH_AT91 || AVR32)
  67         help
  68           This selects a driver for the Atmel SPI Controller, present on
  69           many AT32 (AVR32) and AT91 (ARM) chips.
  70
  71 config SPI_BFIN
  72         tristate "SPI controller driver for ADI Blackfin5xx"
  73         depends on BLACKFIN
  74         help
  75           This is the SPI controller master driver for Blackfin 5xx processor.
  76
  77 config SPI_AU1550
  78         tristate "Au1550/Au12x0 SPI Controller"
  79         depends on (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
  80         select SPI_BITBANG
  81         help
  82           If you say yes to this option, support will be included for the
  83           Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
  84
  85           This driver can also be built as a module.  If so, the module
  86           will be called au1550_spi.
  87
  88 config SPI_BITBANG
  89         tristate "Utilities for Bitbanging SPI masters"
  90         help
  91           With a few GPIO pins, your system can bitbang the SPI protocol.
  92           Select this to get SPI support through I/O pins (GPIO, parallel
  93           port, etc).  Or, some systems' SPI master controller drivers use
  94           this code to manage the per-word or per-transfer accesses to the
  95           hardware shift registers.
  96
  97           This is library code, and is automatically selected by drivers that
  98           need it.  You only need to select this explicitly to support driver
  99           modules that aren't part of this kernel tree.
 100
 101 config SPI_BUTTERFLY
 102         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 103         depends on PARPORT
 104         select SPI_BITBANG
 105         help
 106           This uses a custom parallel port cable to connect to an AVR
 107           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 108           inexpensive battery powered microcontroller evaluation board.
 109           This same cable can be used to flash new firmware.
 110
 111 config SPI_COLDFIRE_QSPI
 112         tristate "Freescale Coldfire QSPI controller"
 113         depends on (M520x || M523x || M5249 || M527x || M528x || M532x)
 114         help
 115           This enables support for the Coldfire QSPI controller in master
 116           mode.
 117
 118           This driver can also be built as a module.  If so, the module
 119           will be called coldfire_qspi.
 120
 121 config SPI_DAVINCI
 122         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 123         depends on SPI_MASTER && ARCH_DAVINCI
 124         select SPI_BITBANG
 125         help
 126           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 127
 128           This driver can also be built as a module. The module will be called
 129           davinci_spi.
 130
 131 config SPI_EP93XX
 132         tristate "Cirrus Logic EP93xx SPI controller"
 133         depends on ARCH_EP93XX
 134         help
 135           This enables using the Cirrus EP93xx SPI controller in master
 136           mode.
 137
 138           To compile this driver as a module, choose M here. The module will be
 139           called ep93xx_spi.
 140
 141 config SPI_GPIO
 142         tristate "GPIO-based bitbanging SPI Master"
 143         depends on GENERIC_GPIO
 144         select SPI_BITBANG
 145         help
 146           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 147           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 148           slaves connected to a bus using this driver are configured as usual,
 149           except that the spi_board_info.controller_data holds the GPIO number
 150           for the chipselect used by this controller driver.
 151
 152           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 153           making it unusually slow for SPI.  If your platform can inline
 154           GPIO operations, you should be able to leverage that for better
 155           speed with a custom version of this driver; see the source code.
 156
 157 config SPI_IMX_VER_IMX1
 158         def_bool y if SOC_IMX1
 159
 160 config SPI_IMX_VER_0_0
 161         def_bool y if SOC_IMX21 || SOC_IMX27
 162
 163 config SPI_IMX_VER_0_4
 164         def_bool y if ARCH_MX31
 165
 166 config SPI_IMX_VER_0_7
 167         def_bool y if ARCH_MX25 || ARCH_MX35 || ARCH_MX51 || ARCH_MX53
 168
 169 config SPI_IMX_VER_2_3
 170         def_bool y if ARCH_MX51 || ARCH_MX53
 171
 172 config SPI_IMX
 173         tristate "Freescale i.MX SPI controllers"
 174         depends on ARCH_MXC
 175         select SPI_BITBANG
 176         default m if IMX_HAVE_PLATFORM_SPI_IMX
 177         help
 178           This enables using the Freescale i.MX SPI controllers in master
 179           mode.
 180
 181 config SPI_LM70_LLP
 182         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 183         depends on PARPORT && EXPERIMENTAL
 184         select SPI_BITBANG
 185         help
 186           This driver supports the NS LM70 LLP Evaluation Board,
 187           which interfaces to an LM70 temperature sensor using
 188           a parallel port.
 189
 190 config SPI_MPC52xx
 191         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 192         depends on PPC_MPC52xx && SPI
 193         select SPI_MASTER_OF
 194         help
 195           This drivers supports the MPC52xx SPI controller in master SPI
 196           mode.
 197
 198 config SPI_MPC52xx_PSC
 199         tristate "Freescale MPC52xx PSC SPI controller"
 200         depends on PPC_MPC52xx && EXPERIMENTAL
 201         help
 202           This enables using the Freescale MPC52xx Programmable Serial
 203           Controller in master SPI mode.
 204
 205 config SPI_MPC512x_PSC
 206         tristate "Freescale MPC512x PSC SPI controller"
 207         depends on SPI_MASTER && PPC_MPC512x
 208         help
 209           This enables using the Freescale MPC5121 Programmable Serial
 210           Controller in SPI master mode.
 211
 212 config SPI_FSL_LIB
 213         tristate
 214         depends on FSL_SOC
 215
 216 config SPI_FSL_SPI
 217         tristate "Freescale SPI controller"
 218         depends on FSL_SOC
 219         select SPI_FSL_LIB
 220         help
 221           This enables using the Freescale SPI controllers in master mode.
 222           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 223           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 224
 225 config SPI_FSL_ESPI
 226         tristate "Freescale eSPI controller"
 227         depends on FSL_SOC
 228         select SPI_FSL_LIB
 229         help
 230           This enables using the Freescale eSPI controllers in master mode.
 231           From MPC8536, 85xx platform uses the controller, and all P10xx,
 232           P20xx, P30xx,P40xx, P50xx uses this controller.
 233
 234 config SPI_OC_TINY
 235         tristate "OpenCores tiny SPI"
 236         depends on GENERIC_GPIO
 237         select SPI_BITBANG
 238         help
 239           This is the driver for OpenCores tiny SPI master controller.
 240
 241 config SPI_OMAP_UWIRE
 242         tristate "OMAP1 MicroWire"
 243         depends on ARCH_OMAP1
 244         select SPI_BITBANG
 245         help
 246           This hooks up to the MicroWire controller on OMAP1 chips.
 247
 248 config SPI_OMAP24XX
 249         tristate "McSPI driver for OMAP"
 250         depends on ARCH_OMAP2PLUS
 251         help
 252           SPI master controller for OMAP24XX and later Multichannel SPI
 253           (McSPI) modules.
 254
 255 config SPI_OMAP_100K
 256         tristate "OMAP SPI 100K"
 257         depends on SPI_MASTER && (ARCH_OMAP850 || ARCH_OMAP730)
 258         help
 259           OMAP SPI 100K master controller for omap7xx boards.
 260
 261 config SPI_ORION
 262         tristate "Orion SPI master (EXPERIMENTAL)"
 263         depends on PLAT_ORION && EXPERIMENTAL
 264         help
 265           This enables using the SPI master controller on the Orion chips.
 266
 267 config SPI_PL022
 268         tristate "ARM AMBA PL022 SSP controller (EXPERIMENTAL)"
 269         depends on ARM_AMBA && EXPERIMENTAL
 270         default y if MACH_U300
 271         default y if ARCH_REALVIEW
 272         default y if INTEGRATOR_IMPD1
 273         default y if ARCH_VERSATILE
 274         help
 275           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 276           controller. If you have an embedded system with an AMBA(R)
 277           bus and a PL022 controller, say Y or M here.
 278
 279 config SPI_PPC4xx
 280         tristate "PPC4xx SPI Controller"
 281         depends on PPC32 && 4xx && SPI_MASTER
 282         select SPI_BITBANG
 283         help
 284           This selects a driver for the PPC4xx SPI Controller.
 285
 286 config SPI_PXA2XX
 287         tristate "PXA2xx SSP SPI master"
 288         depends on (ARCH_PXA || (X86_32 && PCI)) && EXPERIMENTAL
 289         select PXA_SSP if ARCH_PXA
 290         help
 291           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 292           controller. The driver can be configured to use any SSP port and
 293           additional documentation can be found a Documentation/spi/pxa2xx.
 294
 295 config SPI_PXA2XX_PCI
 296         def_bool SPI_PXA2XX && X86_32 && PCI
 297
 298 config SPI_S3C24XX
 299         tristate "Samsung S3C24XX series SPI"
 300         depends on ARCH_S3C2410 && EXPERIMENTAL
 301         select SPI_BITBANG
 302         help
 303           SPI driver for Samsung S3C24XX series ARM SoCs
 304
 305 config SPI_S3C24XX_FIQ
 306         bool "S3C24XX driver with FIQ pseudo-DMA"
 307         depends on SPI_S3C24XX
 308         select FIQ
 309         help
 310           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 311           DMA by using the fast-interrupt request framework, This allows
 312           the driver to get DMA-like performance when there are either
 313           no free DMA channels, or when doing transfers that required both
 314           TX and RX data paths.
 315
 316 config SPI_S3C24XX_GPIO
 317         tristate "Samsung S3C24XX series SPI by GPIO"
 318         depends on ARCH_S3C2410 && EXPERIMENTAL
 319         select SPI_BITBANG
 320         help
 321           SPI driver for Samsung S3C24XX series ARM SoCs using
 322           GPIO lines to provide the SPI bus. This can be used where
 323           the inbuilt hardware cannot provide the transfer mode, or
 324           where the board is using non hardware connected pins.
 325
 326 config SPI_S3C64XX
 327         tristate "Samsung S3C64XX series type SPI"
 328         depends on (ARCH_S3C64XX || ARCH_S5P64X0)
 329         select S3C64XX_DMA if ARCH_S3C64XX
 330         help
 331           SPI driver for Samsung S3C64XX and newer SoCs.
 332
 333 config SPI_SH_MSIOF
 334         tristate "SuperH MSIOF SPI controller"
 335         depends on SUPERH && HAVE_CLK
 336         select SPI_BITBANG
 337         help
 338           SPI driver for SuperH MSIOF blocks.
 339
 340 config SPI_SH_SCI
 341         tristate "SuperH SCI SPI controller"
 342         depends on SUPERH
 343         select SPI_BITBANG
 344         help
 345           SPI driver for SuperH SCI blocks.
 346
 347 config SPI_STMP3XXX
 348         tristate "Freescale STMP37xx/378x SPI/SSP controller"
 349         depends on ARCH_STMP3XXX && SPI_MASTER
 350         help
 351           SPI driver for Freescale STMP37xx/378x SoC SSP interface
 352
 353 config SPI_TEGRA
 354         tristate "Nvidia Tegra SPI controller"
 355         depends on ARCH_TEGRA
 356         select TEGRA_SYSTEM_DMA
 357         help
 358           SPI driver for NVidia Tegra SoCs
 359
 360 config SPI_TOPCLIFF_PCH
 361         tristate "Topcliff PCH SPI Controller"
 362         depends on PCI
 363         help
 364           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 365           used in some x86 embedded processors.
 366
 367 config SPI_TXX9
 368         tristate "Toshiba TXx9 SPI controller"
 369         depends on GENERIC_GPIO && CPU_TX49XX
 370         help
 371           SPI driver for Toshiba TXx9 MIPS SoCs
 372
 373 config SPI_XILINX
 374         tristate "Xilinx SPI controller common module"
 375         depends on HAS_IOMEM && EXPERIMENTAL
 376         select SPI_BITBANG
 377         help
 378           This exposes the SPI controller IP from the Xilinx EDK.
 379
 380           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 381           Product Specification document (DS464) for hardware details.
 382
 383           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 384
 385 config SPI_NUC900
 386         tristate "Nuvoton NUC900 series SPI"
 387         depends on ARCH_W90X900 && EXPERIMENTAL
 388         select SPI_BITBANG
 389         help
 390           SPI driver for Nuvoton NUC900 series ARM SoCs
 391
 392 #
 393 # Add new SPI master controllers in alphabetical order above this line
 394 #
 395
 396 config SPI_DESIGNWARE
 397         tristate "DesignWare SPI controller core support"
 398         depends on SPI_MASTER
 399         help
 400           general driver for SPI controller core from DesignWare
 401
 402 config SPI_DW_PCI
 403         tristate "PCI interface driver for DW SPI core"
 404         depends on SPI_DESIGNWARE && PCI
 405
 406 config SPI_DW_MID_DMA
 407         bool "DMA support for DW SPI controller on Intel Moorestown platform"
 408         depends on SPI_DW_PCI && INTEL_MID_DMAC
 409
 410 config SPI_DW_MMIO
 411         tristate "Memory-mapped io interface driver for DW SPI core"
 412         depends on SPI_DESIGNWARE && HAVE_CLK
 413
 414 #
 415 # There are lots of SPI device types, with sensors and memory
 416 # being probably the most widely used ones.
 417 #
 418 comment "SPI Protocol Masters"
 419
 420 config SPI_SPIDEV
 421         tristate "User mode SPI device driver support"
 422         depends on EXPERIMENTAL
 423         help
 424           This supports user mode SPI protocol drivers.
 425
 426           Note that this application programming interface is EXPERIMENTAL
 427           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 428
 429 config SPI_TLE62X0
 430         tristate "Infineon TLE62X0 (for power switching)"
 431         depends on SYSFS
 432         help
 433           SPI driver for Infineon TLE62X0 series line driver chips,
 434           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 435           sysfs interface, with each line presented as a kind of GPIO
 436           exposing both switch control and diagnostic feedback.
 437
 438 #
 439 # Add new SPI protocol masters in alphabetical order above this line
 440 #
 441
 442 endif # SPI_MASTER
 443
 444 # (slave support would go here)
 445
 446 endif # SPI