drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         boolean "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       boolean "SPI Master Support"
  44         boolean
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ALTERA
  57         tristate "Altera SPI Controller"
  58         select SPI_BITBANG
  59         help
  60           This is the driver for the Altera SPI Controller.
  61
  62 config SPI_ATH79
  63         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  64         depends on ATH79 && GPIOLIB
  65         select SPI_BITBANG
  66         help
  67           This enables support for the SPI controller present on the
  68           Atheros AR71XX/AR724X/AR913X SoCs.
  69
  70 config SPI_ATMEL
  71         tristate "Atmel SPI Controller"
  72         depends on HAS_DMA
  73         depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
  74         help
  75           This selects a driver for the Atmel SPI Controller, present on
  76           many AT32 (AVR32) and AT91 (ARM) chips.
  77
  78 config SPI_BCM2835
  79         tristate "BCM2835 SPI controller"
  80         depends on ARCH_BCM2835 || COMPILE_TEST
  81         help
  82           This selects a driver for the Broadcom BCM2835 SPI master.
  83
  84           The BCM2835 contains two types of SPI master controller; the
  85           "universal SPI master", and the regular SPI controller. This driver
  86           is for the regular SPI controller. Slave mode operation is not also
  87           not supported.
  88
  89 config SPI_BFIN5XX
  90         tristate "SPI controller driver for ADI Blackfin5xx"
  91         depends on BLACKFIN && !BF60x
  92         help
  93           This is the SPI controller master driver for Blackfin 5xx processor.
  94
  95 config SPI_ADI_V3
  96         tristate "SPI controller v3 for ADI"
  97         depends on BF60x
  98         help
  99           This is the SPI controller v3 master driver
 100           found on Blackfin 60x processor.
 101
 102 config SPI_BFIN_SPORT
 103         tristate "SPI bus via Blackfin SPORT"
 104         depends on BLACKFIN
 105         help
 106           Enable support for a SPI bus via the Blackfin SPORT peripheral.
 107
 108 config SPI_AU1550
 109         tristate "Au1550/Au1200/Au1300 SPI Controller"
 110         depends on MIPS_ALCHEMY
 111         select SPI_BITBANG
 112         help
 113           If you say yes to this option, support will be included for the
 114           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
 115
 116 config SPI_BCM53XX
 117         tristate "Broadcom BCM53xx SPI controller"
 118         depends on ARCH_BCM_5301X
 119         depends on BCMA_POSSIBLE
 120         select BCMA
 121         help
 122           Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
 123
 124 config SPI_BCM63XX
 125         tristate "Broadcom BCM63xx SPI controller"
 126         depends on BCM63XX
 127         help
 128           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 129
 130 config SPI_BCM63XX_HSSPI
 131         tristate "Broadcom BCM63XX HS SPI controller driver"
 132         depends on BCM63XX || COMPILE_TEST
 133         help
 134           This enables support for the High Speed SPI controller present on
 135           newer Broadcom BCM63XX SoCs.
 136
 137 config SPI_BITBANG
 138         tristate "Utilities for Bitbanging SPI masters"
 139         help
 140           With a few GPIO pins, your system can bitbang the SPI protocol.
 141           Select this to get SPI support through I/O pins (GPIO, parallel
 142           port, etc).  Or, some systems' SPI master controller drivers use
 143           this code to manage the per-word or per-transfer accesses to the
 144           hardware shift registers.
 145
 146           This is library code, and is automatically selected by drivers that
 147           need it.  You only need to select this explicitly to support driver
 148           modules that aren't part of this kernel tree.
 149
 150 config SPI_BUTTERFLY
 151         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 152         depends on PARPORT
 153         select SPI_BITBANG
 154         help
 155           This uses a custom parallel port cable to connect to an AVR
 156           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 157           inexpensive battery powered microcontroller evaluation board.
 158           This same cable can be used to flash new firmware.
 159
 160 config SPI_CADENCE
 161         tristate "Cadence SPI controller"
 162         depends on ARM
 163         help
 164           This selects the Cadence SPI controller master driver
 165           used by Xilinx Zynq.
 166
 167 config SPI_CLPS711X
 168         tristate "CLPS711X host SPI controller"
 169         depends on ARCH_CLPS711X || COMPILE_TEST
 170         help
 171           This enables dedicated general purpose SPI/Microwire1-compatible
 172           master mode interface (SSI1) for CLPS711X-based CPUs.
 173
 174 config SPI_COLDFIRE_QSPI
 175         tristate "Freescale Coldfire QSPI controller"
 176         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 177         help
 178           This enables support for the Coldfire QSPI controller in master
 179           mode.
 180
 181 config SPI_DAVINCI
 182         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 183         depends on ARCH_DAVINCI || ARCH_KEYSTONE
 184         select SPI_BITBANG
 185         help
 186           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 187
 188 config SPI_EFM32
 189         tristate "EFM32 SPI controller"
 190         depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
 191         select SPI_BITBANG
 192         help
 193           Driver for the spi controller found on Energy Micro's EFM32 SoCs.
 194
 195 config SPI_EP93XX
 196         tristate "Cirrus Logic EP93xx SPI controller"
 197         depends on HAS_DMA
 198         depends on ARCH_EP93XX || COMPILE_TEST
 199         help
 200           This enables using the Cirrus EP93xx SPI controller in master
 201           mode.
 202
 203 config SPI_FALCON
 204         tristate "Falcon SPI controller support"
 205         depends on SOC_FALCON
 206         help
 207           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 208           emulation that is designed for serial flash access. This driver
 209           has only been tested with m25p80 type chips. The hardware has no
 210           support for other types of SPI peripherals.
 211
 212 config SPI_GPIO
 213         tristate "GPIO-based bitbanging SPI Master"
 214         depends on GPIOLIB
 215         select SPI_BITBANG
 216         help
 217           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 218           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 219           slaves connected to a bus using this driver are configured as usual,
 220           except that the spi_board_info.controller_data holds the GPIO number
 221           for the chipselect used by this controller driver.
 222
 223           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 224           making it unusually slow for SPI.  If your platform can inline
 225           GPIO operations, you should be able to leverage that for better
 226           speed with a custom version of this driver; see the source code.
 227
 228 config SPI_IMG_SPFI
 229         tristate "IMG SPFI controller"
 230         depends on MIPS || COMPILE_TEST
 231         help
 232           This enables support for the SPFI master controller found on
 233           IMG SoCs.
 234
 235 config SPI_IMX
 236         tristate "Freescale i.MX SPI controllers"
 237         depends on ARCH_MXC || COMPILE_TEST
 238         select SPI_BITBANG
 239         help
 240           This enables using the Freescale i.MX SPI controllers in master
 241           mode.
 242
 243 config SPI_LM70_LLP
 244         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 245         depends on PARPORT
 246         select SPI_BITBANG
 247         help
 248           This driver supports the NS LM70 LLP Evaluation Board,
 249           which interfaces to an LM70 temperature sensor using
 250           a parallel port.
 251
 252 config SPI_MPC52xx
 253         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 254         depends on PPC_MPC52xx
 255         help
 256           This drivers supports the MPC52xx SPI controller in master SPI
 257           mode.
 258
 259 config SPI_MPC52xx_PSC
 260         tristate "Freescale MPC52xx PSC SPI controller"
 261         depends on PPC_MPC52xx
 262         help
 263           This enables using the Freescale MPC52xx Programmable Serial
 264           Controller in master SPI mode.
 265
 266 config SPI_MPC512x_PSC
 267         tristate "Freescale MPC512x PSC SPI controller"
 268         depends on PPC_MPC512x
 269         help
 270           This enables using the Freescale MPC5121 Programmable Serial
 271           Controller in SPI master mode.
 272
 273 config SPI_FSL_LIB
 274         tristate
 275         depends on OF
 276
 277 config SPI_FSL_CPM
 278         tristate
 279         depends on FSL_SOC
 280
 281 config SPI_FSL_SPI
 282         bool "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
 283         depends on OF
 284         select SPI_FSL_LIB
 285         select SPI_FSL_CPM if FSL_SOC
 286         help
 287           This enables using the Freescale SPI controllers in master mode.
 288           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 289           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 290           This also enables using the Aeroflex Gaisler GRLIB SPI controller in
 291           master mode.
 292
 293 config SPI_FSL_DSPI
 294         tristate "Freescale DSPI controller"
 295         select SPI_BITBANG
 296         select REGMAP_MMIO
 297         depends on SOC_VF610 || COMPILE_TEST
 298         help
 299           This enables support for the Freescale DSPI controller in master
 300           mode. VF610 platform uses the controller.
 301
 302 config SPI_FSL_ESPI
 303         bool "Freescale eSPI controller"
 304         depends on FSL_SOC
 305         select SPI_FSL_LIB
 306         help
 307           This enables using the Freescale eSPI controllers in master mode.
 308           From MPC8536, 85xx platform uses the controller, and all P10xx,
 309           P20xx, P30xx,P40xx, P50xx uses this controller.
 310
 311 config SPI_MESON_SPIFC
 312         tristate "Amlogic Meson SPIFC controller"
 313         depends on ARCH_MESON || COMPILE_TEST
 314         select REGMAP_MMIO
 315         help
 316           This enables master mode support for the SPIFC (SPI flash
 317           controller) available in Amlogic Meson SoCs.
 318
 319 config SPI_OC_TINY
 320         tristate "OpenCores tiny SPI"
 321         depends on GPIOLIB
 322         select SPI_BITBANG
 323         help
 324           This is the driver for OpenCores tiny SPI master controller.
 325
 326 config SPI_OCTEON
 327         tristate "Cavium OCTEON SPI controller"
 328         depends on CAVIUM_OCTEON_SOC
 329         help
 330           SPI host driver for the hardware found on some Cavium OCTEON
 331           SOCs.
 332
 333 config SPI_OMAP_UWIRE
 334         tristate "OMAP1 MicroWire"
 335         depends on ARCH_OMAP1
 336         select SPI_BITBANG
 337         help
 338           This hooks up to the MicroWire controller on OMAP1 chips.
 339
 340 config SPI_OMAP24XX
 341         tristate "McSPI driver for OMAP"
 342         depends on HAS_DMA
 343         depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
 344         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 345         help
 346           SPI master controller for OMAP24XX and later Multichannel SPI
 347           (McSPI) modules.
 348
 349 config SPI_TI_QSPI
 350         tristate "DRA7xxx QSPI controller support"
 351         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 352         help
 353           QSPI master controller for DRA7xxx used for flash devices.
 354           This device supports single, dual and quad read support, while
 355           it only supports single write mode.
 356
 357 config SPI_OMAP_100K
 358         tristate "OMAP SPI 100K"
 359         depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
 360         help
 361           OMAP SPI 100K master controller for omap7xx boards.
 362
 363 config SPI_ORION
 364         tristate "Orion SPI master"
 365         depends on PLAT_ORION || COMPILE_TEST
 366         help
 367           This enables using the SPI master controller on the Orion chips.
 368
 369 config SPI_PL022
 370         tristate "ARM AMBA PL022 SSP controller"
 371         depends on ARM_AMBA
 372         default y if MACH_U300
 373         default y if ARCH_REALVIEW
 374         default y if INTEGRATOR_IMPD1
 375         default y if ARCH_VERSATILE
 376         help
 377           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 378           controller. If you have an embedded system with an AMBA(R)
 379           bus and a PL022 controller, say Y or M here.
 380
 381 config SPI_PPC4xx
 382         tristate "PPC4xx SPI Controller"
 383         depends on PPC32 && 4xx
 384         select SPI_BITBANG
 385         help
 386           This selects a driver for the PPC4xx SPI Controller.
 387
 388 config SPI_PXA2XX_PXADMA
 389         bool "PXA2xx SSP legacy PXA DMA API support"
 390         depends on SPI_PXA2XX && ARCH_PXA
 391         help
 392           Enable PXA private legacy DMA API support. Note that this is
 393           deprecated in favor of generic DMA engine API.
 394
 395 config SPI_PXA2XX_DMA
 396         def_bool y
 397         depends on SPI_PXA2XX && !SPI_PXA2XX_PXADMA
 398
 399 config SPI_PXA2XX
 400         tristate "PXA2xx SSP SPI master"
 401         depends on (ARCH_PXA || PCI || ACPI)
 402         select PXA_SSP if ARCH_PXA
 403         help
 404           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 405           controller. The driver can be configured to use any SSP port and
 406           additional documentation can be found a Documentation/spi/pxa2xx.
 407
 408 config SPI_PXA2XX_PCI
 409         def_tristate SPI_PXA2XX && PCI && COMMON_CLK
 410
 411 config SPI_ROCKCHIP
 412         tristate "Rockchip SPI controller driver"
 413         depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
 414         help
 415           This selects a driver for Rockchip SPI controller.
 416
 417           If you say yes to this option, support will be included for
 418           RK3066, RK3188 and RK3288 families of SPI controller.
 419           Rockchip SPI controller support DMA transport and PIO mode.
 420           The main usecase of this controller is to use spi flash as boot
 421           device.
 422
 423 config SPI_RSPI
 424         tristate "Renesas RSPI/QSPI controller"
 425         depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
 426         help
 427           SPI driver for Renesas RSPI and QSPI blocks.
 428
 429 config SPI_QUP
 430         tristate "Qualcomm SPI controller with QUP interface"
 431         depends on ARCH_QCOM || (ARM && COMPILE_TEST)
 432         help
 433           Qualcomm Universal Peripheral (QUP) core is an AHB slave that
 434           provides a common data path (an output FIFO and an input FIFO)
 435           for serial peripheral interface (SPI) mini-core. SPI in master
 436           mode supports up to 50MHz, up to four chip selects, programmable
 437           data path from 4 bits to 32 bits and numerous protocol variants.
 438
 439           This driver can also be built as a module.  If so, the module
 440           will be called spi_qup.
 441
 442 config SPI_S3C24XX
 443         tristate "Samsung S3C24XX series SPI"
 444         depends on ARCH_S3C24XX
 445         select SPI_BITBANG
 446         help
 447           SPI driver for Samsung S3C24XX series ARM SoCs
 448
 449 config SPI_S3C24XX_FIQ
 450         bool "S3C24XX driver with FIQ pseudo-DMA"
 451         depends on SPI_S3C24XX
 452         select FIQ
 453         help
 454           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 455           DMA by using the fast-interrupt request framework, This allows
 456           the driver to get DMA-like performance when there are either
 457           no free DMA channels, or when doing transfers that required both
 458           TX and RX data paths.
 459
 460 config SPI_S3C64XX
 461         tristate "Samsung S3C64XX series type SPI"
 462         depends on (PLAT_SAMSUNG || ARCH_EXYNOS)
 463         select S3C64XX_PL080 if ARCH_S3C64XX
 464         help
 465           SPI driver for Samsung S3C64XX and newer SoCs.
 466
 467 config SPI_SC18IS602
 468         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 469         depends on I2C
 470         help
 471           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 472
 473 config SPI_SH_MSIOF
 474         tristate "SuperH MSIOF SPI controller"
 475         depends on HAVE_CLK && HAS_DMA
 476         depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
 477         help
 478           SPI driver for SuperH and SH Mobile MSIOF blocks.
 479
 480 config SPI_SH
 481         tristate "SuperH SPI controller"
 482         depends on SUPERH || COMPILE_TEST
 483         help
 484           SPI driver for SuperH SPI blocks.
 485
 486 config SPI_SH_SCI
 487         tristate "SuperH SCI SPI controller"
 488         depends on SUPERH
 489         select SPI_BITBANG
 490         help
 491           SPI driver for SuperH SCI blocks.
 492
 493 config SPI_SH_HSPI
 494         tristate "SuperH HSPI controller"
 495         depends on ARCH_SHMOBILE || COMPILE_TEST
 496         help
 497           SPI driver for SuperH HSPI blocks.
 498
 499 config SPI_SIRF
 500         tristate "CSR SiRFprimaII SPI controller"
 501         depends on SIRF_DMA
 502         select SPI_BITBANG
 503         help
 504           SPI driver for CSR SiRFprimaII SoCs
 505
 506 config SPI_SUN4I
 507         tristate "Allwinner A10 SoCs SPI controller"
 508         depends on ARCH_SUNXI || COMPILE_TEST
 509         help
 510           SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
 511
 512 config SPI_SUN6I
 513         tristate "Allwinner A31 SPI controller"
 514         depends on ARCH_SUNXI || COMPILE_TEST
 515         depends on RESET_CONTROLLER
 516         help
 517           This enables using the SPI controller on the Allwinner A31 SoCs.
 518
 519 config SPI_MXS
 520         tristate "Freescale MXS SPI controller"
 521         depends on ARCH_MXS
 522         select STMP_DEVICE
 523         help
 524           SPI driver for Freescale MXS devices.
 525
 526 config SPI_TEGRA114
 527         tristate "NVIDIA Tegra114 SPI Controller"
 528         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 529         depends on RESET_CONTROLLER && HAS_DMA
 530         help
 531           SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
 532           is different than the older SoCs SPI controller and also register interface
 533           get changed with this controller.
 534
 535 config SPI_TEGRA20_SFLASH
 536         tristate "Nvidia Tegra20 Serial flash Controller"
 537         depends on ARCH_TEGRA || COMPILE_TEST
 538         depends on RESET_CONTROLLER
 539         help
 540           SPI driver for Nvidia Tegra20 Serial flash Controller interface.
 541           The main usecase of this controller is to use spi flash as boot
 542           device.
 543
 544 config SPI_TEGRA20_SLINK
 545         tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
 546         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 547         depends on RESET_CONTROLLER && HAS_DMA
 548         help
 549           SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
 550
 551 config SPI_TOPCLIFF_PCH
 552         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
 553         depends on PCI && (X86_32 || COMPILE_TEST)
 554         help
 555           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 556           used in some x86 embedded processors.
 557
 558           This driver also supports the ML7213/ML7223/ML7831, a companion chip
 559           for the Atom E6xx series and compatible with the Intel EG20T PCH.
 560
 561 config SPI_TXX9
 562         tristate "Toshiba TXx9 SPI controller"
 563         depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
 564         help
 565           SPI driver for Toshiba TXx9 MIPS SoCs
 566
 567 config SPI_XCOMM
 568         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
 569         depends on I2C
 570         help
 571           Support for the SPI-I2C bridge found on the Analog Devices
 572           AD-FMCOMMS1-EBZ board.
 573
 574 config SPI_XILINX
 575         tristate "Xilinx SPI controller common module"
 576         depends on HAS_IOMEM
 577         select SPI_BITBANG
 578         help
 579           This exposes the SPI controller IP from the Xilinx EDK.
 580
 581           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 582           Product Specification document (DS464) for hardware details.
 583
 584           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 585
 586 config SPI_XTENSA_XTFPGA
 587         tristate "Xtensa SPI controller for xtfpga"
 588         depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
 589         select SPI_BITBANG
 590         help
 591           SPI driver for xtfpga SPI master controller.
 592
 593           This simple SPI master controller is built into xtfpga bitstreams
 594           and is used to control daughterboard audio codec. It always transfers
 595           16 bit words in SPI mode 0, automatically asserting CS on transfer
 596           start and deasserting on end.
 597
 598
 599 config SPI_NUC900
 600         tristate "Nuvoton NUC900 series SPI"
 601         depends on ARCH_W90X900
 602         select SPI_BITBANG
 603         help
 604           SPI driver for Nuvoton NUC900 series ARM SoCs
 605
 606 #
 607 # Add new SPI master controllers in alphabetical order above this line
 608 #
 609
 610 config SPI_DESIGNWARE
 611         tristate "DesignWare SPI controller core support"
 612         help
 613           general driver for SPI controller core from DesignWare
 614
 615 config SPI_DW_PCI
 616         tristate "PCI interface driver for DW SPI core"
 617         depends on SPI_DESIGNWARE && PCI
 618
 619 config SPI_DW_MID_DMA
 620         bool "DMA support for DW SPI controller on Intel MID platform"
 621         depends on SPI_DW_PCI && INTEL_MID_DMAC
 622
 623 config SPI_DW_MMIO
 624         tristate "Memory-mapped io interface driver for DW SPI core"
 625         depends on SPI_DESIGNWARE
 626
 627 #
 628 # There are lots of SPI device types, with sensors and memory
 629 # being probably the most widely used ones.
 630 #
 631 comment "SPI Protocol Masters"
 632
 633 config SPI_SPIDEV
 634         tristate "User mode SPI device driver support"
 635         help
 636           This supports user mode SPI protocol drivers.
 637
 638           Note that this application programming interface is EXPERIMENTAL
 639           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 640
 641 config SPI_TLE62X0
 642         tristate "Infineon TLE62X0 (for power switching)"
 643         depends on SYSFS
 644         help
 645           SPI driver for Infineon TLE62X0 series line driver chips,
 646           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 647           sysfs interface, with each line presented as a kind of GPIO
 648           exposing both switch control and diagnostic feedback.
 649
 650 #
 651 # Add new SPI protocol masters in alphabetical order above this line
 652 #
 653
 654 endif # SPI_MASTER
 655
 656 # (slave support would go here)
 657
 658 endif # SPI