drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         bool "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       bool "SPI Master Support"
  44         bool
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ALTERA
  57         tristate "Altera SPI Controller"
  58         select SPI_BITBANG
  59         help
  60           This is the driver for the Altera SPI Controller.
  61
  62 config SPI_ATH79
  63         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  64         depends on ATH79 && GPIOLIB
  65         select SPI_BITBANG
  66         help
  67           This enables support for the SPI controller present on the
  68           Atheros AR71XX/AR724X/AR913X SoCs.
  69
  70 config SPI_ARMADA_3700
  71         tristate "Marvell Armada 3700 SPI Controller"
  72         depends on (ARCH_MVEBU && OF) || COMPILE_TEST
  73         help
  74           This enables support for the SPI controller present on the
  75           Marvell Armada 3700 SoCs.
  76
  77 config SPI_ATMEL
  78         tristate "Atmel SPI Controller"
  79         depends on HAS_DMA
  80         depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
  81         help
  82           This selects a driver for the Atmel SPI Controller, present on
  83           many AT32 (AVR32) and AT91 (ARM) chips.
  84
  85 config SPI_AU1550
  86         tristate "Au1550/Au1200/Au1300 SPI Controller"
  87         depends on MIPS_ALCHEMY
  88         select SPI_BITBANG
  89         help
  90           If you say yes to this option, support will be included for the
  91           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
  92
  93 config SPI_AXI_SPI_ENGINE
  94         tristate "Analog Devices AXI SPI Engine controller"
  95         depends on HAS_IOMEM
  96         help
  97           This enables support for the Analog Devices AXI SPI Engine SPI controller.
  98           It is part of the SPI Engine framework that is used in some Analog Devices
  99           reference designs for FPGAs.
 100
 101 config SPI_BCM2835
 102         tristate "BCM2835 SPI controller"
 103         depends on GPIOLIB
 104         depends on ARCH_BCM2835 || COMPILE_TEST
 105         help
 106           This selects a driver for the Broadcom BCM2835 SPI master.
 107
 108           The BCM2835 contains two types of SPI master controller; the
 109           "universal SPI master", and the regular SPI controller. This driver
 110           is for the regular SPI controller. Slave mode operation is not also
 111           not supported.
 112
 113 config SPI_BCM2835AUX
 114         tristate "BCM2835 SPI auxiliary controller"
 115         depends on (ARCH_BCM2835 && GPIOLIB) || COMPILE_TEST
 116         help
 117           This selects a driver for the Broadcom BCM2835 SPI aux master.
 118
 119           The BCM2835 contains two types of SPI master controller; the
 120           "universal SPI master", and the regular SPI controller.
 121           This driver is for the universal/auxiliary SPI controller.
 122
 123 config SPI_BFIN5XX
 124         tristate "SPI controller driver for ADI Blackfin5xx"
 125         depends on BLACKFIN && !BF60x
 126         help
 127           This is the SPI controller master driver for Blackfin 5xx processor.
 128
 129 config SPI_ADI_V3
 130         tristate "SPI controller v3 for ADI"
 131         depends on BF60x
 132         help
 133           This is the SPI controller v3 master driver
 134           found on Blackfin 60x processor.
 135
 136 config SPI_BFIN_SPORT
 137         tristate "SPI bus via Blackfin SPORT"
 138         depends on BLACKFIN
 139         help
 140           Enable support for a SPI bus via the Blackfin SPORT peripheral.
 141
 142 config SPI_BCM53XX
 143         tristate "Broadcom BCM53xx SPI controller"
 144         depends on ARCH_BCM_5301X
 145         depends on BCMA_POSSIBLE
 146         select BCMA
 147         help
 148           Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
 149
 150 config SPI_BCM63XX
 151         tristate "Broadcom BCM63xx SPI controller"
 152         depends on BCM63XX || COMPILE_TEST
 153         help
 154           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 155
 156 config SPI_BCM63XX_HSSPI
 157         tristate "Broadcom BCM63XX HS SPI controller driver"
 158         depends on BCM63XX || COMPILE_TEST
 159         help
 160           This enables support for the High Speed SPI controller present on
 161           newer Broadcom BCM63XX SoCs.
 162
 163 config SPI_BCM_QSPI
 164         tristate "Broadcom BSPI and MSPI controller support"
 165         depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST
 166         default ARCH_BCM_IPROC
 167         help
 168           Enables support for the Broadcom SPI flash and MSPI controller.
 169           Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
 170           based platforms. This driver works for both SPI master for spi-nor
 171           flash device as well as MSPI device.
 172
 173 config SPI_BITBANG
 174         tristate "Utilities for Bitbanging SPI masters"
 175         help
 176           With a few GPIO pins, your system can bitbang the SPI protocol.
 177           Select this to get SPI support through I/O pins (GPIO, parallel
 178           port, etc).  Or, some systems' SPI master controller drivers use
 179           this code to manage the per-word or per-transfer accesses to the
 180           hardware shift registers.
 181
 182           This is library code, and is automatically selected by drivers that
 183           need it.  You only need to select this explicitly to support driver
 184           modules that aren't part of this kernel tree.
 185
 186 config SPI_BUTTERFLY
 187         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 188         depends on PARPORT
 189         select SPI_BITBANG
 190         help
 191           This uses a custom parallel port cable to connect to an AVR
 192           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 193           inexpensive battery powered microcontroller evaluation board.
 194           This same cable can be used to flash new firmware.
 195
 196 config SPI_CADENCE
 197         tristate "Cadence SPI controller"
 198         help
 199           This selects the Cadence SPI controller master driver
 200           used by Xilinx Zynq and ZynqMP.
 201
 202 config SPI_CLPS711X
 203         tristate "CLPS711X host SPI controller"
 204         depends on ARCH_CLPS711X || COMPILE_TEST
 205         help
 206           This enables dedicated general purpose SPI/Microwire1-compatible
 207           master mode interface (SSI1) for CLPS711X-based CPUs.
 208
 209 config SPI_COLDFIRE_QSPI
 210         tristate "Freescale Coldfire QSPI controller"
 211         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 212         help
 213           This enables support for the Coldfire QSPI controller in master
 214           mode.
 215
 216 config SPI_DAVINCI
 217         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 218         depends on ARCH_DAVINCI || ARCH_KEYSTONE
 219         select SPI_BITBANG
 220         help
 221           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 222
 223 config SPI_DESIGNWARE
 224         tristate "DesignWare SPI controller core support"
 225         help
 226           general driver for SPI controller core from DesignWare
 227
 228 config SPI_DW_PCI
 229         tristate "PCI interface driver for DW SPI core"
 230         depends on SPI_DESIGNWARE && PCI
 231
 232 config SPI_DW_MID_DMA
 233         bool "DMA support for DW SPI controller on Intel MID platform"
 234         depends on SPI_DW_PCI && DW_DMAC_PCI
 235
 236 config SPI_DW_MMIO
 237         tristate "Memory-mapped io interface driver for DW SPI core"
 238         depends on SPI_DESIGNWARE
 239
 240 config SPI_DLN2
 241        tristate "Diolan DLN-2 USB SPI adapter"
 242        depends on MFD_DLN2
 243        help
 244          If you say yes to this option, support will be included for Diolan
 245          DLN2, a USB to SPI interface.
 246
 247          This driver can also be built as a module.  If so, the module
 248          will be called spi-dln2.
 249
 250 config SPI_EFM32
 251         tristate "EFM32 SPI controller"
 252         depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
 253         select SPI_BITBANG
 254         help
 255           Driver for the spi controller found on Energy Micro's EFM32 SoCs.
 256
 257 config SPI_EP93XX
 258         tristate "Cirrus Logic EP93xx SPI controller"
 259         depends on HAS_DMA
 260         depends on ARCH_EP93XX || COMPILE_TEST
 261         help
 262           This enables using the Cirrus EP93xx SPI controller in master
 263           mode.
 264
 265 config SPI_FALCON
 266         tristate "Falcon SPI controller support"
 267         depends on SOC_FALCON
 268         help
 269           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 270           emulation that is designed for serial flash access. This driver
 271           has only been tested with m25p80 type chips. The hardware has no
 272           support for other types of SPI peripherals.
 273
 274 config SPI_FSL_LPSPI
 275         tristate "Freescale i.MX LPSPI controller"
 276         depends on ARCH_MXC || COMPILE_TEST
 277         help
 278           This enables Freescale i.MX LPSPI controllers in master mode.
 279
 280 config SPI_GPIO
 281         tristate "GPIO-based bitbanging SPI Master"
 282         depends on GPIOLIB || COMPILE_TEST
 283         select SPI_BITBANG
 284         help
 285           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 286           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 287           slaves connected to a bus using this driver are configured as usual,
 288           except that the spi_board_info.controller_data holds the GPIO number
 289           for the chipselect used by this controller driver.
 290
 291           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 292           making it unusually slow for SPI.  If your platform can inline
 293           GPIO operations, you should be able to leverage that for better
 294           speed with a custom version of this driver; see the source code.
 295
 296 config SPI_IMG_SPFI
 297         tristate "IMG SPFI controller"
 298         depends on MIPS || COMPILE_TEST
 299         help
 300           This enables support for the SPFI master controller found on
 301           IMG SoCs.
 302
 303 config SPI_IMX
 304         tristate "Freescale i.MX SPI controllers"
 305         depends on ARCH_MXC || COMPILE_TEST
 306         select SPI_BITBANG
 307         help
 308           This enables using the Freescale i.MX SPI controllers in master
 309           mode.
 310
 311 config SPI_JCORE
 312         tristate "J-Core SPI Master"
 313         depends on OF && (SUPERH || COMPILE_TEST)
 314         help
 315           This enables support for the SPI master controller in the J-Core
 316           synthesizable, open source SoC.
 317
 318 config SPI_LM70_LLP
 319         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 320         depends on PARPORT
 321         select SPI_BITBANG
 322         help
 323           This driver supports the NS LM70 LLP Evaluation Board,
 324           which interfaces to an LM70 temperature sensor using
 325           a parallel port.
 326
 327 config SPI_LP8841_RTC
 328         tristate "ICP DAS LP-8841 SPI Controller for RTC"
 329         depends on MACH_PXA27X_DT || COMPILE_TEST
 330         help
 331           This driver provides an SPI master device to drive Maxim
 332           DS-1302 real time clock.
 333
 334           Say N here unless you plan to run the kernel on an ICP DAS
 335           LP-8x4x industrial computer.
 336
 337 config SPI_MPC52xx
 338         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 339         depends on PPC_MPC52xx
 340         help
 341           This drivers supports the MPC52xx SPI controller in master SPI
 342           mode.
 343
 344 config SPI_MPC52xx_PSC
 345         tristate "Freescale MPC52xx PSC SPI controller"
 346         depends on PPC_MPC52xx
 347         help
 348           This enables using the Freescale MPC52xx Programmable Serial
 349           Controller in master SPI mode.
 350
 351 config SPI_MPC512x_PSC
 352         tristate "Freescale MPC512x PSC SPI controller"
 353         depends on PPC_MPC512x
 354         help
 355           This enables using the Freescale MPC5121 Programmable Serial
 356           Controller in SPI master mode.
 357
 358 config SPI_FSL_LIB
 359         tristate
 360         depends on OF
 361
 362 config SPI_FSL_CPM
 363         tristate
 364         depends on FSL_SOC
 365
 366 config SPI_FSL_SPI
 367         tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
 368         depends on OF
 369         select SPI_FSL_LIB
 370         select SPI_FSL_CPM if FSL_SOC
 371         help
 372           This enables using the Freescale SPI controllers in master mode.
 373           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 374           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 375           This also enables using the Aeroflex Gaisler GRLIB SPI controller in
 376           master mode.
 377
 378 config SPI_FSL_DSPI
 379         tristate "Freescale DSPI controller"
 380         select REGMAP_MMIO
 381         depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
 382         help
 383           This enables support for the Freescale DSPI controller in master
 384           mode. VF610 platform uses the controller.
 385
 386 config SPI_FSL_ESPI
 387         tristate "Freescale eSPI controller"
 388         depends on FSL_SOC
 389         help
 390           This enables using the Freescale eSPI controllers in master mode.
 391           From MPC8536, 85xx platform uses the controller, and all P10xx,
 392           P20xx, P30xx,P40xx, P50xx uses this controller.
 393
 394 config SPI_MESON_SPIFC
 395         tristate "Amlogic Meson SPIFC controller"
 396         depends on ARCH_MESON || COMPILE_TEST
 397         select REGMAP_MMIO
 398         help
 399           This enables master mode support for the SPIFC (SPI flash
 400           controller) available in Amlogic Meson SoCs.
 401
 402 config SPI_MT65XX
 403         tristate "MediaTek SPI controller"
 404         depends on ARCH_MEDIATEK || COMPILE_TEST
 405         help
 406           This selects the MediaTek(R) SPI bus driver.
 407           If you want to use MediaTek(R) SPI interface,
 408           say Y or M here.If you are not sure, say N.
 409           SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
 410
 411 config SPI_NUC900
 412         tristate "Nuvoton NUC900 series SPI"
 413         depends on ARCH_W90X900
 414         select SPI_BITBANG
 415         help
 416           SPI driver for Nuvoton NUC900 series ARM SoCs
 417
 418 config SPI_OC_TINY
 419         tristate "OpenCores tiny SPI"
 420         depends on GPIOLIB || COMPILE_TEST
 421         select SPI_BITBANG
 422         help
 423           This is the driver for OpenCores tiny SPI master controller.
 424
 425 config SPI_OCTEON
 426         tristate "Cavium OCTEON SPI controller"
 427         depends on CAVIUM_OCTEON_SOC
 428         help
 429           SPI host driver for the hardware found on some Cavium OCTEON
 430           SOCs.
 431
 432 config SPI_OMAP_UWIRE
 433         tristate "OMAP1 MicroWire"
 434         depends on ARCH_OMAP1
 435         select SPI_BITBANG
 436         help
 437           This hooks up to the MicroWire controller on OMAP1 chips.
 438
 439 config SPI_OMAP24XX
 440         tristate "McSPI driver for OMAP"
 441         depends on HAS_DMA
 442         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 443         select SG_SPLIT
 444         help
 445           SPI master controller for OMAP24XX and later Multichannel SPI
 446           (McSPI) modules.
 447
 448 config SPI_TI_QSPI
 449         tristate "DRA7xxx QSPI controller support"
 450         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 451         help
 452           QSPI master controller for DRA7xxx used for flash devices.
 453           This device supports single, dual and quad read support, while
 454           it only supports single write mode.
 455
 456 config SPI_OMAP_100K
 457         tristate "OMAP SPI 100K"
 458         depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
 459         help
 460           OMAP SPI 100K master controller for omap7xx boards.
 461
 462 config SPI_ORION
 463         tristate "Orion SPI master"
 464         depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
 465         help
 466           This enables using the SPI master controller on the Orion
 467           and MVEBU chips.
 468
 469 config SPI_PIC32
 470         tristate "Microchip PIC32 series SPI"
 471         depends on MACH_PIC32 || COMPILE_TEST
 472         help
 473           SPI driver for Microchip PIC32 SPI master controller.
 474
 475 config SPI_PIC32_SQI
 476         tristate "Microchip PIC32 Quad SPI driver"
 477         depends on MACH_PIC32 || COMPILE_TEST
 478         depends on HAS_DMA
 479         help
 480           SPI driver for PIC32 Quad SPI controller.
 481
 482 config SPI_PL022
 483         tristate "ARM AMBA PL022 SSP controller"
 484         depends on ARM_AMBA
 485         default y if MACH_U300
 486         default y if ARCH_REALVIEW
 487         default y if INTEGRATOR_IMPD1
 488         default y if ARCH_VERSATILE
 489         help
 490           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 491           controller. If you have an embedded system with an AMBA(R)
 492           bus and a PL022 controller, say Y or M here.
 493
 494 config SPI_PPC4xx
 495         tristate "PPC4xx SPI Controller"
 496         depends on PPC32 && 4xx
 497         select SPI_BITBANG
 498         help
 499           This selects a driver for the PPC4xx SPI Controller.
 500
 501 config SPI_PXA2XX
 502         tristate "PXA2xx SSP SPI master"
 503         depends on (ARCH_PXA || PCI || ACPI)
 504         select PXA_SSP if ARCH_PXA
 505         help
 506           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 507           controller. The driver can be configured to use any SSP port and
 508           additional documentation can be found a Documentation/spi/pxa2xx.
 509
 510 config SPI_PXA2XX_PCI
 511         def_tristate SPI_PXA2XX && PCI && COMMON_CLK
 512
 513 config SPI_ROCKCHIP
 514         tristate "Rockchip SPI controller driver"
 515         help
 516           This selects a driver for Rockchip SPI controller.
 517
 518           If you say yes to this option, support will be included for
 519           RK3066, RK3188 and RK3288 families of SPI controller.
 520           Rockchip SPI controller support DMA transport and PIO mode.
 521           The main usecase of this controller is to use spi flash as boot
 522           device.
 523
 524 config SPI_RB4XX
 525         tristate "Mikrotik RB4XX SPI master"
 526         depends on SPI_MASTER && ATH79
 527         help
 528           SPI controller driver for the Mikrotik RB4xx series boards.
 529
 530 config SPI_RSPI
 531         tristate "Renesas RSPI/QSPI controller"
 532         depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
 533         help
 534           SPI driver for Renesas RSPI and QSPI blocks.
 535
 536 config SPI_QUP
 537         tristate "Qualcomm SPI controller with QUP interface"
 538         depends on ARCH_QCOM || (ARM && COMPILE_TEST)
 539         help
 540           Qualcomm Universal Peripheral (QUP) core is an AHB slave that
 541           provides a common data path (an output FIFO and an input FIFO)
 542           for serial peripheral interface (SPI) mini-core. SPI in master
 543           mode supports up to 50MHz, up to four chip selects, programmable
 544           data path from 4 bits to 32 bits and numerous protocol variants.
 545
 546           This driver can also be built as a module.  If so, the module
 547           will be called spi_qup.
 548
 549 config SPI_S3C24XX
 550         tristate "Samsung S3C24XX series SPI"
 551         depends on ARCH_S3C24XX
 552         select SPI_BITBANG
 553         help
 554           SPI driver for Samsung S3C24XX series ARM SoCs
 555
 556 config SPI_S3C24XX_FIQ
 557         bool "S3C24XX driver with FIQ pseudo-DMA"
 558         depends on SPI_S3C24XX
 559         select FIQ
 560         help
 561           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 562           DMA by using the fast-interrupt request framework, This allows
 563           the driver to get DMA-like performance when there are either
 564           no free DMA channels, or when doing transfers that required both
 565           TX and RX data paths.
 566
 567 config SPI_S3C64XX
 568         tristate "Samsung S3C64XX series type SPI"
 569         depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
 570         help
 571           SPI driver for Samsung S3C64XX and newer SoCs.
 572
 573 config SPI_SC18IS602
 574         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 575         depends on I2C
 576         help
 577           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 578
 579 config SPI_SH_MSIOF
 580         tristate "SuperH MSIOF SPI controller"
 581         depends on HAVE_CLK && HAS_DMA
 582         depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
 583         help
 584           SPI driver for SuperH and SH Mobile MSIOF blocks.
 585
 586 config SPI_SH
 587         tristate "SuperH SPI controller"
 588         depends on SUPERH || COMPILE_TEST
 589         help
 590           SPI driver for SuperH SPI blocks.
 591
 592 config SPI_SH_SCI
 593         tristate "SuperH SCI SPI controller"
 594         depends on SUPERH
 595         select SPI_BITBANG
 596         help
 597           SPI driver for SuperH SCI blocks.
 598
 599 config SPI_SH_HSPI
 600         tristate "SuperH HSPI controller"
 601         depends on ARCH_RENESAS || COMPILE_TEST
 602         help
 603           SPI driver for SuperH HSPI blocks.
 604
 605 config SPI_SIRF
 606         tristate "CSR SiRFprimaII SPI controller"
 607         depends on SIRF_DMA
 608         select SPI_BITBANG
 609         help
 610           SPI driver for CSR SiRFprimaII SoCs
 611
 612 config SPI_ST_SSC4
 613         tristate "STMicroelectronics SPI SSC-based driver"
 614         depends on ARCH_STI || COMPILE_TEST
 615         help
 616           STMicroelectronics SoCs support for SPI. If you say yes to
 617           this option, support will be included for the SSC driven SPI.
 618
 619 config SPI_SUN4I
 620         tristate "Allwinner A10 SoCs SPI controller"
 621         depends on ARCH_SUNXI || COMPILE_TEST
 622         help
 623           SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
 624
 625 config SPI_SUN6I
 626         tristate "Allwinner A31 SPI controller"
 627         depends on ARCH_SUNXI || COMPILE_TEST
 628         depends on RESET_CONTROLLER
 629         help
 630           This enables using the SPI controller on the Allwinner A31 SoCs.
 631
 632 config SPI_MXS
 633         tristate "Freescale MXS SPI controller"
 634         depends on ARCH_MXS
 635         select STMP_DEVICE
 636         help
 637           SPI driver for Freescale MXS devices.
 638
 639 config SPI_TEGRA114
 640         tristate "NVIDIA Tegra114 SPI Controller"
 641         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 642         depends on RESET_CONTROLLER && HAS_DMA
 643         help
 644           SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
 645           is different than the older SoCs SPI controller and also register interface
 646           get changed with this controller.
 647
 648 config SPI_TEGRA20_SFLASH
 649         tristate "Nvidia Tegra20 Serial flash Controller"
 650         depends on ARCH_TEGRA || COMPILE_TEST
 651         depends on RESET_CONTROLLER
 652         help
 653           SPI driver for Nvidia Tegra20 Serial flash Controller interface.
 654           The main usecase of this controller is to use spi flash as boot
 655           device.
 656
 657 config SPI_TEGRA20_SLINK
 658         tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
 659         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 660         depends on RESET_CONTROLLER && HAS_DMA
 661         help
 662           SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
 663
 664 config SPI_THUNDERX
 665         tristate "Cavium ThunderX SPI controller"
 666         depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
 667         help
 668           SPI host driver for the hardware found on Cavium ThunderX
 669           SOCs.
 670
 671 config SPI_TOPCLIFF_PCH
 672         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
 673         depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
 674         help
 675           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 676           used in some x86 embedded processors.
 677
 678           This driver also supports the ML7213/ML7223/ML7831, a companion chip
 679           for the Atom E6xx series and compatible with the Intel EG20T PCH.
 680
 681 config SPI_TXX9
 682         tristate "Toshiba TXx9 SPI controller"
 683         depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
 684         help
 685           SPI driver for Toshiba TXx9 MIPS SoCs
 686
 687 config SPI_XCOMM
 688         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
 689         depends on I2C
 690         help
 691           Support for the SPI-I2C bridge found on the Analog Devices
 692           AD-FMCOMMS1-EBZ board.
 693
 694 config SPI_XILINX
 695         tristate "Xilinx SPI controller common module"
 696         depends on HAS_IOMEM
 697         select SPI_BITBANG
 698         help
 699           This exposes the SPI controller IP from the Xilinx EDK.
 700
 701           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 702           Product Specification document (DS464) for hardware details.
 703
 704           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 705
 706 config SPI_XLP
 707         tristate "Netlogic XLP SPI controller driver"
 708         depends on CPU_XLP || ARCH_VULCAN || COMPILE_TEST
 709         help
 710           Enable support for the SPI controller on the Netlogic XLP SoCs.
 711           Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
 712           and XLP5XX.
 713
 714           If you have a Netlogic XLP platform say Y here.
 715           If unsure, say N.
 716
 717 config SPI_XTENSA_XTFPGA
 718         tristate "Xtensa SPI controller for xtfpga"
 719         depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
 720         select SPI_BITBANG
 721         help
 722           SPI driver for xtfpga SPI master controller.
 723
 724           This simple SPI master controller is built into xtfpga bitstreams
 725           and is used to control daughterboard audio codec. It always transfers
 726           16 bit words in SPI mode 0, automatically asserting CS on transfer
 727           start and deasserting on end.
 728
 729 config SPI_ZYNQMP_GQSPI
 730         tristate "Xilinx ZynqMP GQSPI controller"
 731         depends on SPI_MASTER && HAS_DMA
 732         help
 733           Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
 734
 735 #
 736 # Add new SPI master controllers in alphabetical order above this line
 737 #
 738
 739 #
 740 # There are lots of SPI device types, with sensors and memory
 741 # being probably the most widely used ones.
 742 #
 743 comment "SPI Protocol Masters"
 744
 745 config SPI_SPIDEV
 746         tristate "User mode SPI device driver support"
 747         help
 748           This supports user mode SPI protocol drivers.
 749
 750           Note that this application programming interface is EXPERIMENTAL
 751           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 752
 753 config SPI_LOOPBACK_TEST
 754         tristate "spi loopback test framework support"
 755         depends on m
 756         help
 757           This enables the SPI loopback testing framework driver
 758
 759           primarily used for development of spi_master drivers
 760           and to detect regressions
 761
 762 config SPI_TLE62X0
 763         tristate "Infineon TLE62X0 (for power switching)"
 764         depends on SYSFS
 765         help
 766           SPI driver for Infineon TLE62X0 series line driver chips,
 767           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 768           sysfs interface, with each line presented as a kind of GPIO
 769           exposing both switch control and diagnostic feedback.
 770
 771 #
 772 # Add new SPI protocol masters in alphabetical order above this line
 773 #
 774
 775 endif # SPI_MASTER
 776
 777 # (slave support would go here)
 778
 779 endif # SPI