]> git.proxmox.com Git - mirror_ubuntu-jammy-kernel.git/blob - drivers/usb/gadget/udc/omap_udc.c
projects / mirror_ubuntu-jammy-kernel.git / blob
? search:


3a16431da3211c470db38e5e2980996142073b65
[mirror_ubuntu-jammy-kernel.git] / drivers / usb / gadget / udc / omap_udc.c
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * omap_udc.c -- for OMAP full speed udc; most chips support OTG.
4 *
5 * Copyright (C) 2004 Texas Instruments, Inc.
6 * Copyright (C) 2004-2005 David Brownell
7 *
8 * OMAP2 & DMA support by Kyungmin Park <kyungmin.park@samsung.com>
9 */
10
11 #undef DEBUG
12 #undef VERBOSE
13
14 #include <linux/module.h>
15 #include <linux/kernel.h>
16 #include <linux/ioport.h>
17 #include <linux/types.h>
18 #include <linux/errno.h>
19 #include <linux/delay.h>
20 #include <linux/slab.h>
21 #include <linux/timer.h>
22 #include <linux/list.h>
23 #include <linux/interrupt.h>
24 #include <linux/proc_fs.h>
25 #include <linux/mm.h>
26 #include <linux/moduleparam.h>
27 #include <linux/platform_device.h>
28 #include <linux/usb/ch9.h>
29 #include <linux/usb/gadget.h>
30 #include <linux/usb/otg.h>
31 #include <linux/dma-mapping.h>
32 #include <linux/clk.h>
33 #include <linux/err.h>
34 #include <linux/prefetch.h>
35 #include <linux/io.h>
36
37 #include <asm/byteorder.h>
38 #include <asm/irq.h>
39 #include <asm/unaligned.h>
40 #include <asm/mach-types.h>
41
42 #include <linux/omap-dma.h>
43
44 #include <mach/usb.h>
45
46 #include "omap_udc.h"
47
48 #undef USB_TRACE
49
50 /* bulk DMA seems to be behaving for both IN and OUT */
51 #define USE_DMA
52
53 /* ISO too */
54 #define USE_ISO
55
56 #define DRIVER_DESC "OMAP UDC driver"
57 #define DRIVER_VERSION "4 October 2004"
58
59 #define OMAP_DMA_USB_W2FC_TX0 29
60 #define OMAP_DMA_USB_W2FC_RX0 26
61
62 /*
63 * The OMAP UDC needs _very_ early endpoint setup: before enabling the
64 * D+ pullup to allow enumeration. That's too early for the gadget
65 * framework to use from usb_endpoint_enable(), which happens after
66 * enumeration as part of activating an interface. (But if we add an
67 * optional new "UDC not yet running" state to the gadget driver model,
68 * even just during driver binding, the endpoint autoconfig logic is the
69 * natural spot to manufacture new endpoints.)
70 *
71 * So instead of using endpoint enable calls to control the hardware setup,
72 * this driver defines a "fifo mode" parameter. It's used during driver
73 * initialization to choose among a set of pre-defined endpoint configs.
74 * See omap_udc_setup() for available modes, or to add others. That code
75 * lives in an init section, so use this driver as a module if you need
76 * to change the fifo mode after the kernel boots.
77 *
78 * Gadget drivers normally ignore endpoints they don't care about, and
79 * won't include them in configuration descriptors. That means only
80 * misbehaving hosts would even notice they exist.
81 */
82 #ifdef USE_ISO
83 static unsigned fifo_mode = 3;
84 #else
85 static unsigned fifo_mode;
86 #endif
87
88 /* "modprobe omap_udc fifo_mode=42", or else as a kernel
89 * boot parameter "omap_udc:fifo_mode=42"
90 */
91 module_param(fifo_mode, uint, 0);
92 MODULE_PARM_DESC(fifo_mode, "endpoint configuration");
93
94 #ifdef USE_DMA
95 static bool use_dma = 1;
96
97 /* "modprobe omap_udc use_dma=y", or else as a kernel
98 * boot parameter "omap_udc:use_dma=y"
99 */
100 module_param(use_dma, bool, 0);
101 MODULE_PARM_DESC(use_dma, "enable/disable DMA");
102 #else /* !USE_DMA */
103
104 /* save a bit of code */
105 #define use_dma 0
106 #endif /* !USE_DMA */
107
108
109 static const char driver_name[] = "omap_udc";
110 static const char driver_desc[] = DRIVER_DESC;
111
112 /*-------------------------------------------------------------------------*/
113
114 /* there's a notion of "current endpoint" for modifying endpoint
115 * state, and PIO access to its FIFO.
116 */
117
118 static void use_ep(struct omap_ep *ep, u16 select)
119 {
120 u16 num = ep->bEndpointAddress & 0x0f;
121
122 if (ep->bEndpointAddress & USB_DIR_IN)
123 num |= UDC_EP_DIR;
124 omap_writew(num | select, UDC_EP_NUM);
125 /* when select, MUST deselect later !! */
126 }
127
128 static inline void deselect_ep(void)
129 {
130 u16 w;
131
132 w = omap_readw(UDC_EP_NUM);
133 w &= ~UDC_EP_SEL;
134 omap_writew(w, UDC_EP_NUM);
135 /* 6 wait states before TX will happen */
136 }
137
138 static void dma_channel_claim(struct omap_ep *ep, unsigned preferred);
139
140 /*-------------------------------------------------------------------------*/
141
142 static int omap_ep_enable(struct usb_ep *_ep,
143 const struct usb_endpoint_descriptor *desc)
144 {
145 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep);
146 struct omap_udc *udc;
147 unsigned long flags;
148 u16 maxp;
149
150 /* catch various bogus parameters */
151 if (!_ep || !desc
152 || desc->bDescriptorType != USB_DT_ENDPOINT
153 || ep->bEndpointAddress != desc->bEndpointAddress
154 || ep->maxpacket < usb_endpoint_maxp(desc)) {
155 DBG("%s, bad ep or descriptor\n", __func__);
156 return -EINVAL;
157 }
158 maxp = usb_endpoint_maxp(desc);
159 if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK
160 && maxp != ep->maxpacket)
161 || usb_endpoint_maxp(desc) > ep->maxpacket
162 || !desc->wMaxPacketSize) {
163 DBG("%s, bad %s maxpacket\n", __func__, _ep->name);
164 return -ERANGE;
165 }
166
167 #ifdef USE_ISO
168 if ((desc->bmAttributes == USB_ENDPOINT_XFER_ISOC
169 && desc->bInterval != 1)) {
170 /* hardware wants period = 1; USB allows 2^(Interval-1) */
171 DBG("%s, unsupported ISO period %dms\n", _ep->name,
172 1 << (desc->bInterval - 1));
173 return -EDOM;
174 }
175 #else
176 if (desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
177 DBG("%s, ISO nyet\n", _ep->name);
178 return -EDOM;
179 }
180 #endif
181
182 /* xfer types must match, except that interrupt ~= bulk */
183 if (ep->bmAttributes != desc->bmAttributes
184 && ep->bmAttributes != USB_ENDPOINT_XFER_BULK
185 && desc->bmAttributes != USB_ENDPOINT_XFER_INT) {
186 DBG("%s, %s type mismatch\n", __func__, _ep->name);
187 return -EINVAL;
188 }
189
190 udc = ep->udc;
191 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) {
192 DBG("%s, bogus device state\n", __func__);
193 return -ESHUTDOWN;
194 }
195
196 spin_lock_irqsave(&udc->lock, flags);
197
198 ep->ep.desc = desc;
199 ep->irqs = 0;
200 ep->stopped = 0;
201 ep->ep.maxpacket = maxp;
202
203 /* set endpoint to initial state */
204 ep->dma_channel = 0;
205 ep->has_dma = 0;
206 ep->lch = -1;
207 use_ep(ep, UDC_EP_SEL);
208 omap_writew(udc->clr_halt, UDC_CTRL);
209 ep->ackwait = 0;
210 deselect_ep();
211
212 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC)
213 list_add(&ep->iso, &udc->iso);
214
215 /* maybe assign a DMA channel to this endpoint */
216 if (use_dma && desc->bmAttributes == USB_ENDPOINT_XFER_BULK)
217 /* FIXME ISO can dma, but prefers first channel */
218 dma_channel_claim(ep, 0);
219
220 /* PIO OUT may RX packets */
221 if (desc->bmAttributes != USB_ENDPOINT_XFER_ISOC
222 && !ep->has_dma
223 && !(ep->bEndpointAddress & USB_DIR_IN)) {
224 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
225 ep->ackwait = 1 + ep->double_buf;
226 }
227
228 spin_unlock_irqrestore(&udc->lock, flags);
229 VDBG("%s enabled\n", _ep->name);
230 return 0;
231 }
232
233 static void nuke(struct omap_ep *, int status);
234
235 static int omap_ep_disable(struct usb_ep *_ep)
236 {
237 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep);
238 unsigned long flags;
239
240 if (!_ep || !ep->ep.desc) {
241 DBG("%s, %s not enabled\n", __func__,
242 _ep ? ep->ep.name : NULL);
243 return -EINVAL;
244 }
245
246 spin_lock_irqsave(&ep->udc->lock, flags);
247 ep->ep.desc = NULL;
248 nuke(ep, -ESHUTDOWN);
249 ep->ep.maxpacket = ep->maxpacket;
250 ep->has_dma = 0;
251 omap_writew(UDC_SET_HALT, UDC_CTRL);
252 list_del_init(&ep->iso);
253 del_timer(&ep->timer);
254
255 spin_unlock_irqrestore(&ep->udc->lock, flags);
256
257 VDBG("%s disabled\n", _ep->name);
258 return 0;
259 }
260
261 /*-------------------------------------------------------------------------*/
262
263 static struct usb_request *
264 omap_alloc_request(struct usb_ep *ep, gfp_t gfp_flags)
265 {
266 struct omap_req *req;
267
268 req = kzalloc(sizeof(*req), gfp_flags);
269 if (!req)
270 return NULL;
271
272 INIT_LIST_HEAD(&req->queue);
273
274 return &req->req;
275 }
276
277 static void
278 omap_free_request(struct usb_ep *ep, struct usb_request *_req)
279 {
280 struct omap_req *req = container_of(_req, struct omap_req, req);
281
282 kfree(req);
283 }
284
285 /*-------------------------------------------------------------------------*/
286
287 static void
288 done(struct omap_ep *ep, struct omap_req *req, int status)
289 {
290 struct omap_udc *udc = ep->udc;
291 unsigned stopped = ep->stopped;
292
293 list_del_init(&req->queue);
294
295 if (req->req.status == -EINPROGRESS)
296 req->req.status = status;
297 else
298 status = req->req.status;
299
300 if (use_dma && ep->has_dma)
301 usb_gadget_unmap_request(&udc->gadget, &req->req,
302 (ep->bEndpointAddress & USB_DIR_IN));
303
304 #ifndef USB_TRACE
305 if (status && status != -ESHUTDOWN)
306 #endif
307 VDBG("complete %s req %p stat %d len %u/%u\n",
308 ep->ep.name, &req->req, status,
309 req->req.actual, req->req.length);
310
311 /* don't modify queue heads during completion callback */
312 ep->stopped = 1;
313 spin_unlock(&ep->udc->lock);
314 usb_gadget_giveback_request(&ep->ep, &req->req);
315 spin_lock(&ep->udc->lock);
316 ep->stopped = stopped;
317 }
318
319 /*-------------------------------------------------------------------------*/
320
321 #define UDC_FIFO_FULL (UDC_NON_ISO_FIFO_FULL | UDC_ISO_FIFO_FULL)
322 #define UDC_FIFO_UNWRITABLE (UDC_EP_HALTED | UDC_FIFO_FULL)
323
324 #define FIFO_EMPTY (UDC_NON_ISO_FIFO_EMPTY | UDC_ISO_FIFO_EMPTY)
325 #define FIFO_UNREADABLE (UDC_EP_HALTED | FIFO_EMPTY)
326
327 static inline int
328 write_packet(u8 *buf, struct omap_req *req, unsigned max)
329 {
330 unsigned len;
331 u16 *wp;
332
333 len = min(req->req.length - req->req.actual, max);
334 req->req.actual += len;
335
336 max = len;
337 if (likely((((int)buf) & 1) == 0)) {
338 wp = (u16 *)buf;
339 while (max >= 2) {
340 omap_writew(*wp++, UDC_DATA);
341 max -= 2;
342 }
343 buf = (u8 *)wp;
344 }
345 while (max--)
346 omap_writeb(*buf++, UDC_DATA);
347 return len;
348 }
349
350 /* FIXME change r/w fifo calling convention */
351
352
353 /* return: 0 = still running, 1 = completed, negative = errno */
354 static int write_fifo(struct omap_ep *ep, struct omap_req *req)
355 {
356 u8 *buf;
357 unsigned count;
358 int is_last;
359 u16 ep_stat;
360
361 buf = req->req.buf + req->req.actual;
362 prefetch(buf);
363
364 /* PIO-IN isn't double buffered except for iso */
365 ep_stat = omap_readw(UDC_STAT_FLG);
366 if (ep_stat & UDC_FIFO_UNWRITABLE)
367 return 0;
368
369 count = ep->ep.maxpacket;
370 count = write_packet(buf, req, count);
371 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
372 ep->ackwait = 1;
373
374 /* last packet is often short (sometimes a zlp) */
375 if (count != ep->ep.maxpacket)
376 is_last = 1;
377 else if (req->req.length == req->req.actual
378 && !req->req.zero)
379 is_last = 1;
380 else
381 is_last = 0;
382
383 /* NOTE: requests complete when all IN data is in a
384 * FIFO (or sometimes later, if a zlp was needed).
385 * Use usb_ep_fifo_status() where needed.
386 */
387 if (is_last)
388 done(ep, req, 0);
389 return is_last;
390 }
391
392 static inline int
393 read_packet(u8 *buf, struct omap_req *req, unsigned avail)
394 {
395 unsigned len;
396 u16 *wp;
397
398 len = min(req->req.length - req->req.actual, avail);
399 req->req.actual += len;
400 avail = len;
401
402 if (likely((((int)buf) & 1) == 0)) {
403 wp = (u16 *)buf;
404 while (avail >= 2) {
405 *wp++ = omap_readw(UDC_DATA);
406 avail -= 2;
407 }
408 buf = (u8 *)wp;
409 }
410 while (avail--)
411 *buf++ = omap_readb(UDC_DATA);
412 return len;
413 }
414
415 /* return: 0 = still running, 1 = queue empty, negative = errno */
416 static int read_fifo(struct omap_ep *ep, struct omap_req *req)
417 {
418 u8 *buf;
419 unsigned count, avail;
420 int is_last;
421
422 buf = req->req.buf + req->req.actual;
423 prefetchw(buf);
424
425 for (;;) {
426 u16 ep_stat = omap_readw(UDC_STAT_FLG);
427
428 is_last = 0;
429 if (ep_stat & FIFO_EMPTY) {
430 if (!ep->double_buf)
431 break;
432 ep->fnf = 1;
433 }
434 if (ep_stat & UDC_EP_HALTED)
435 break;
436
437 if (ep_stat & UDC_FIFO_FULL)
438 avail = ep->ep.maxpacket;
439 else {
440 avail = omap_readw(UDC_RXFSTAT);
441 ep->fnf = ep->double_buf;
442 }
443 count = read_packet(buf, req, avail);
444
445 /* partial packet reads may not be errors */
446 if (count < ep->ep.maxpacket) {
447 is_last = 1;
448 /* overflowed this request? flush extra data */
449 if (count != avail) {
450 req->req.status = -EOVERFLOW;
451 avail -= count;
452 while (avail--)
453 omap_readw(UDC_DATA);
454 }
455 } else if (req->req.length == req->req.actual)
456 is_last = 1;
457 else
458 is_last = 0;
459
460 if (!ep->bEndpointAddress)
461 break;
462 if (is_last)
463 done(ep, req, 0);
464 break;
465 }
466 return is_last;
467 }
468
469 /*-------------------------------------------------------------------------*/
470
471 static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start)
472 {
473 dma_addr_t end;
474
475 /* IN-DMA needs this on fault/cancel paths, so 15xx misreports
476 * the last transfer's bytecount by more than a FIFO's worth.
477 */
478 if (cpu_is_omap15xx())
479 return 0;
480
481 end = omap_get_dma_src_pos(ep->lch);
482 if (end == ep->dma_counter)
483 return 0;
484
485 end |= start & (0xffff << 16);
486 if (end < start)
487 end += 0x10000;
488 return end - start;
489 }
490
491 static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start)
492 {
493 dma_addr_t end;
494
495 end = omap_get_dma_dst_pos(ep->lch);
496 if (end == ep->dma_counter)
497 return 0;
498
499 end |= start & (0xffff << 16);
500 if (cpu_is_omap15xx())
501 end++;
502 if (end < start)
503 end += 0x10000;
504 return end - start;
505 }
506
507
508 /* Each USB transfer request using DMA maps to one or more DMA transfers.
509 * When DMA completion isn't request completion, the UDC continues with
510 * the next DMA transfer for that USB transfer.
511 */
512
513 static void next_in_dma(struct omap_ep *ep, struct omap_req *req)
514 {
515 u16 txdma_ctrl, w;
516 unsigned length = req->req.length - req->req.actual;
517 const int sync_mode = cpu_is_omap15xx()
518 ? OMAP_DMA_SYNC_FRAME
519 : OMAP_DMA_SYNC_ELEMENT;
520 int dma_trigger = 0;
521
522 /* measure length in either bytes or packets */
523 if ((cpu_is_omap16xx() && length <= UDC_TXN_TSC)
524 || (cpu_is_omap15xx() && length < ep->maxpacket)) {
525 txdma_ctrl = UDC_TXN_EOT | length;
526 omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8,
527 length, 1, sync_mode, dma_trigger, 0);
528 } else {
529 length = min(length / ep->maxpacket,
530 (unsigned) UDC_TXN_TSC + 1);
531 txdma_ctrl = length;
532 omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S16,
533 ep->ep.maxpacket >> 1, length, sync_mode,
534 dma_trigger, 0);
535 length *= ep->maxpacket;
536 }
537 omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_EMIFF,
538 OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual,
539 0, 0);
540
541 omap_start_dma(ep->lch);
542 ep->dma_counter = omap_get_dma_src_pos(ep->lch);
543 w = omap_readw(UDC_DMA_IRQ_EN);
544 w |= UDC_TX_DONE_IE(ep->dma_channel);
545 omap_writew(w, UDC_DMA_IRQ_EN);
546 omap_writew(UDC_TXN_START | txdma_ctrl, UDC_TXDMA(ep->dma_channel));
547 req->dma_bytes = length;
548 }
549
550 static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status)
551 {
552 u16 w;
553
554 if (status == 0) {
555 req->req.actual += req->dma_bytes;
556
557 /* return if this request needs to send data or zlp */
558 if (req->req.actual < req->req.length)
559 return;
560 if (req->req.zero
561 && req->dma_bytes != 0
562 && (req->req.actual % ep->maxpacket) == 0)
563 return;
564 } else
565 req->req.actual += dma_src_len(ep, req->req.dma
566 + req->req.actual);
567
568 /* tx completion */
569 omap_stop_dma(ep->lch);
570 w = omap_readw(UDC_DMA_IRQ_EN);
571 w &= ~UDC_TX_DONE_IE(ep->dma_channel);
572 omap_writew(w, UDC_DMA_IRQ_EN);
573 done(ep, req, status);
574 }
575
576 static void next_out_dma(struct omap_ep *ep, struct omap_req *req)
577 {
578 unsigned packets = req->req.length - req->req.actual;
579 int dma_trigger = 0;
580 u16 w;
581
582 /* set up this DMA transfer, enable the fifo, start */
583 packets /= ep->ep.maxpacket;
584 packets = min(packets, (unsigned)UDC_RXN_TC + 1);
585 req->dma_bytes = packets * ep->ep.maxpacket;
586 omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S16,
587 ep->ep.maxpacket >> 1, packets,
588 OMAP_DMA_SYNC_ELEMENT,
589 dma_trigger, 0);
590 omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_EMIFF,
591 OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual,
592 0, 0);
593 ep->dma_counter = omap_get_dma_dst_pos(ep->lch);
594
595 omap_writew(UDC_RXN_STOP | (packets - 1), UDC_RXDMA(ep->dma_channel));
596 w = omap_readw(UDC_DMA_IRQ_EN);
597 w |= UDC_RX_EOT_IE(ep->dma_channel);
598 omap_writew(w, UDC_DMA_IRQ_EN);
599 omap_writew(ep->bEndpointAddress & 0xf, UDC_EP_NUM);
600 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
601
602 omap_start_dma(ep->lch);
603 }
604
605 static void
606 finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one)
607 {
608 u16 count, w;
609
610 if (status == 0)
611 ep->dma_counter = (u16) (req->req.dma + req->req.actual);
612 count = dma_dest_len(ep, req->req.dma + req->req.actual);
613 count += req->req.actual;
614 if (one)
615 count--;
616 if (count <= req->req.length)
617 req->req.actual = count;
618
619 if (count != req->dma_bytes || status)
620 omap_stop_dma(ep->lch);
621
622 /* if this wasn't short, request may need another transfer */
623 else if (req->req.actual < req->req.length)
624 return;
625
626 /* rx completion */
627 w = omap_readw(UDC_DMA_IRQ_EN);
628 w &= ~UDC_RX_EOT_IE(ep->dma_channel);
629 omap_writew(w, UDC_DMA_IRQ_EN);
630 done(ep, req, status);
631 }
632
633 static void dma_irq(struct omap_udc *udc, u16 irq_src)
634 {
635 u16 dman_stat = omap_readw(UDC_DMAN_STAT);
636 struct omap_ep *ep;
637 struct omap_req *req;
638
639 /* IN dma: tx to host */
640 if (irq_src & UDC_TXN_DONE) {
641 ep = &udc->ep[16 + UDC_DMA_TX_SRC(dman_stat)];
642 ep->irqs++;
643 /* can see TXN_DONE after dma abort */
644 if (!list_empty(&ep->queue)) {
645 req = container_of(ep->queue.next,
646 struct omap_req, queue);
647 finish_in_dma(ep, req, 0);
648 }
649 omap_writew(UDC_TXN_DONE, UDC_IRQ_SRC);
650
651 if (!list_empty(&ep->queue)) {
652 req = container_of(ep->queue.next,
653 struct omap_req, queue);
654 next_in_dma(ep, req);
655 }
656 }
657
658 /* OUT dma: rx from host */
659 if (irq_src & UDC_RXN_EOT) {
660 ep = &udc->ep[UDC_DMA_RX_SRC(dman_stat)];
661 ep->irqs++;
662 /* can see RXN_EOT after dma abort */
663 if (!list_empty(&ep->queue)) {
664 req = container_of(ep->queue.next,
665 struct omap_req, queue);
666 finish_out_dma(ep, req, 0, dman_stat & UDC_DMA_RX_SB);
667 }
668 omap_writew(UDC_RXN_EOT, UDC_IRQ_SRC);
669
670 if (!list_empty(&ep->queue)) {
671 req = container_of(ep->queue.next,
672 struct omap_req, queue);
673 next_out_dma(ep, req);
674 }
675 }
676
677 if (irq_src & UDC_RXN_CNT) {
678 ep = &udc->ep[UDC_DMA_RX_SRC(dman_stat)];
679 ep->irqs++;
680 /* omap15xx does this unasked... */
681 VDBG("%s, RX_CNT irq?\n", ep->ep.name);
682 omap_writew(UDC_RXN_CNT, UDC_IRQ_SRC);
683 }
684 }
685
686 static void dma_error(int lch, u16 ch_status, void *data)
687 {
688 struct omap_ep *ep = data;
689
690 /* if ch_status & OMAP_DMA_DROP_IRQ ... */
691 /* if ch_status & OMAP1_DMA_TOUT_IRQ ... */
692 ERR("%s dma error, lch %d status %02x\n", ep->ep.name, lch, ch_status);
693
694 /* complete current transfer ... */
695 }
696
697 static void dma_channel_claim(struct omap_ep *ep, unsigned channel)
698 {
699 u16 reg;
700 int status, restart, is_in;
701 int dma_channel;
702
703 is_in = ep->bEndpointAddress & USB_DIR_IN;
704 if (is_in)
705 reg = omap_readw(UDC_TXDMA_CFG);
706 else
707 reg = omap_readw(UDC_RXDMA_CFG);
708 reg |= UDC_DMA_REQ; /* "pulse" activated */
709
710 ep->dma_channel = 0;
711 ep->lch = -1;
712 if (channel == 0 || channel > 3) {
713 if ((reg & 0x0f00) == 0)
714 channel = 3;
715 else if ((reg & 0x00f0) == 0)
716 channel = 2;
717 else if ((reg & 0x000f) == 0) /* preferred for ISO */
718 channel = 1;
719 else {
720 status = -EMLINK;
721 goto just_restart;
722 }
723 }
724 reg |= (0x0f & ep->bEndpointAddress) << (4 * (channel - 1));
725 ep->dma_channel = channel;
726
727 if (is_in) {
728 dma_channel = OMAP_DMA_USB_W2FC_TX0 - 1 + channel;
729 status = omap_request_dma(dma_channel,
730 ep->ep.name, dma_error, ep, &ep->lch);
731 if (status == 0) {
732 omap_writew(reg, UDC_TXDMA_CFG);
733 /* EMIFF or SDRC */
734 omap_set_dma_src_burst_mode(ep->lch,
735 OMAP_DMA_DATA_BURST_4);
736 omap_set_dma_src_data_pack(ep->lch, 1);
737 /* TIPB */
738 omap_set_dma_dest_params(ep->lch,
739 OMAP_DMA_PORT_TIPB,
740 OMAP_DMA_AMODE_CONSTANT,
741 UDC_DATA_DMA,
742 0, 0);
743 }
744 } else {
745 dma_channel = OMAP_DMA_USB_W2FC_RX0 - 1 + channel;
746 status = omap_request_dma(dma_channel,
747 ep->ep.name, dma_error, ep, &ep->lch);
748 if (status == 0) {
749 omap_writew(reg, UDC_RXDMA_CFG);
750 /* TIPB */
751 omap_set_dma_src_params(ep->lch,
752 OMAP_DMA_PORT_TIPB,
753 OMAP_DMA_AMODE_CONSTANT,
754 UDC_DATA_DMA,
755 0, 0);
756 /* EMIFF or SDRC */
757 omap_set_dma_dest_burst_mode(ep->lch,
758 OMAP_DMA_DATA_BURST_4);
759 omap_set_dma_dest_data_pack(ep->lch, 1);
760 }
761 }
762 if (status)
763 ep->dma_channel = 0;
764 else {
765 ep->has_dma = 1;
766 omap_disable_dma_irq(ep->lch, OMAP_DMA_BLOCK_IRQ);
767
768 /* channel type P: hw synch (fifo) */
769 if (!cpu_is_omap15xx())
770 omap_set_dma_channel_mode(ep->lch, OMAP_DMA_LCH_P);
771 }
772
773 just_restart:
774 /* restart any queue, even if the claim failed */
775 restart = !ep->stopped && !list_empty(&ep->queue);
776
777 if (status)
778 DBG("%s no dma channel: %d%s\n", ep->ep.name, status,
779 restart ? " (restart)" : "");
780 else
781 DBG("%s claimed %cxdma%d lch %d%s\n", ep->ep.name,
782 is_in ? 't' : 'r',
783 ep->dma_channel - 1, ep->lch,
784 restart ? " (restart)" : "");
785
786 if (restart) {
787 struct omap_req *req;
788 req = container_of(ep->queue.next, struct omap_req, queue);
789 if (ep->has_dma)
790 (is_in ? next_in_dma : next_out_dma)(ep, req);
791 else {
792 use_ep(ep, UDC_EP_SEL);
793 (is_in ? write_fifo : read_fifo)(ep, req);
794 deselect_ep();
795 if (!is_in) {
796 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
797 ep->ackwait = 1 + ep->double_buf;
798 }
799 /* IN: 6 wait states before it'll tx */
800 }
801 }
802 }
803
804 static void dma_channel_release(struct omap_ep *ep)
805 {
806 int shift = 4 * (ep->dma_channel - 1);
807 u16 mask = 0x0f << shift;
808 struct omap_req *req;
809 int active;
810
811 /* abort any active usb transfer request */
812 if (!list_empty(&ep->queue))
813 req = container_of(ep->queue.next, struct omap_req, queue);
814 else
815 req = NULL;
816
817 active = omap_get_dma_active_status(ep->lch);
818
819 DBG("%s release %s %cxdma%d %p\n", ep->ep.name,
820 active ? "active" : "idle",
821 (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r',
822 ep->dma_channel - 1, req);
823
824 /* NOTE: re-setting RX_REQ/TX_REQ because of a chip bug (before
825 * OMAP 1710 ES2.0) where reading the DMA_CFG can clear them.
826 */
827
828 /* wait till current packet DMA finishes, and fifo empties */
829 if (ep->bEndpointAddress & USB_DIR_IN) {
830 omap_writew((omap_readw(UDC_TXDMA_CFG) & ~mask) | UDC_DMA_REQ,
831 UDC_TXDMA_CFG);
832
833 if (req) {
834 finish_in_dma(ep, req, -ECONNRESET);
835
836 /* clear FIFO; hosts probably won't empty it */
837 use_ep(ep, UDC_EP_SEL);
838 omap_writew(UDC_CLR_EP, UDC_CTRL);
839 deselect_ep();
840 }
841 while (omap_readw(UDC_TXDMA_CFG) & mask)
842 udelay(10);
843 } else {
844 omap_writew((omap_readw(UDC_RXDMA_CFG) & ~mask) | UDC_DMA_REQ,
845 UDC_RXDMA_CFG);
846
847 /* dma empties the fifo */
848 while (omap_readw(UDC_RXDMA_CFG) & mask)
849 udelay(10);
850 if (req)
851 finish_out_dma(ep, req, -ECONNRESET, 0);
852 }
853 omap_free_dma(ep->lch);
854 ep->dma_channel = 0;
855 ep->lch = -1;
856 /* has_dma still set, till endpoint is fully quiesced */
857 }
858
859
860 /*-------------------------------------------------------------------------*/
861
862 static int
863 omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
864 {
865 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep);
866 struct omap_req *req = container_of(_req, struct omap_req, req);
867 struct omap_udc *udc;
868 unsigned long flags;
869 int is_iso = 0;
870
871 /* catch various bogus parameters */
872 if (!_req || !req->req.complete || !req->req.buf
873 || !list_empty(&req->queue)) {
874 DBG("%s, bad params\n", __func__);
875 return -EINVAL;
876 }
877 if (!_ep || (!ep->ep.desc && ep->bEndpointAddress)) {
878 DBG("%s, bad ep\n", __func__);
879 return -EINVAL;
880 }
881 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
882 if (req->req.length > ep->ep.maxpacket)
883 return -EMSGSIZE;
884 is_iso = 1;
885 }
886
887 /* this isn't bogus, but OMAP DMA isn't the only hardware to
888 * have a hard time with partial packet reads... reject it.
889 */
890 if (use_dma
891 && ep->has_dma
892 && ep->bEndpointAddress != 0
893 && (ep->bEndpointAddress & USB_DIR_IN) == 0
894 && (req->req.length % ep->ep.maxpacket) != 0) {
895 DBG("%s, no partial packet OUT reads\n", __func__);
896 return -EMSGSIZE;
897 }
898
899 udc = ep->udc;
900 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN)
901 return -ESHUTDOWN;
902
903 if (use_dma && ep->has_dma)
904 usb_gadget_map_request(&udc->gadget, &req->req,
905 (ep->bEndpointAddress & USB_DIR_IN));
906
907 VDBG("%s queue req %p, len %d buf %p\n",
908 ep->ep.name, _req, _req->length, _req->buf);
909
910 spin_lock_irqsave(&udc->lock, flags);
911
912 req->req.status = -EINPROGRESS;
913 req->req.actual = 0;
914
915 /* maybe kickstart non-iso i/o queues */
916 if (is_iso) {
917 u16 w;
918
919 w = omap_readw(UDC_IRQ_EN);
920 w |= UDC_SOF_IE;
921 omap_writew(w, UDC_IRQ_EN);
922 } else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) {
923 int is_in;
924
925 if (ep->bEndpointAddress == 0) {
926 if (!udc->ep0_pending || !list_empty(&ep->queue)) {
927 spin_unlock_irqrestore(&udc->lock, flags);
928 return -EL2HLT;
929 }
930
931 /* empty DATA stage? */
932 is_in = udc->ep0_in;
933 if (!req->req.length) {
934
935 /* chip became CONFIGURED or ADDRESSED
936 * earlier; drivers may already have queued
937 * requests to non-control endpoints
938 */
939 if (udc->ep0_set_config) {
940 u16 irq_en = omap_readw(UDC_IRQ_EN);
941
942 irq_en |= UDC_DS_CHG_IE | UDC_EP0_IE;
943 if (!udc->ep0_reset_config)
944 irq_en |= UDC_EPN_RX_IE
945 | UDC_EPN_TX_IE;
946 omap_writew(irq_en, UDC_IRQ_EN);
947 }
948
949 /* STATUS for zero length DATA stages is
950 * always an IN ... even for IN transfers,
951 * a weird case which seem to stall OMAP.
952 */
953 omap_writew(UDC_EP_SEL | UDC_EP_DIR,
954 UDC_EP_NUM);
955 omap_writew(UDC_CLR_EP, UDC_CTRL);
956 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
957 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
958
959 /* cleanup */
960 udc->ep0_pending = 0;
961 done(ep, req, 0);
962 req = NULL;
963
964 /* non-empty DATA stage */
965 } else if (is_in) {
966 omap_writew(UDC_EP_SEL | UDC_EP_DIR,
967 UDC_EP_NUM);
968 } else {
969 if (udc->ep0_setup)
970 goto irq_wait;
971 omap_writew(UDC_EP_SEL, UDC_EP_NUM);
972 }
973 } else {
974 is_in = ep->bEndpointAddress & USB_DIR_IN;
975 if (!ep->has_dma)
976 use_ep(ep, UDC_EP_SEL);
977 /* if ISO: SOF IRQs must be enabled/disabled! */
978 }
979
980 if (ep->has_dma)
981 (is_in ? next_in_dma : next_out_dma)(ep, req);
982 else if (req) {
983 if ((is_in ? write_fifo : read_fifo)(ep, req) == 1)
984 req = NULL;
985 deselect_ep();
986 if (!is_in) {
987 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
988 ep->ackwait = 1 + ep->double_buf;
989 }
990 /* IN: 6 wait states before it'll tx */
991 }
992 }
993
994 irq_wait:
995 /* irq handler advances the queue */
996 if (req != NULL)
997 list_add_tail(&req->queue, &ep->queue);
998 spin_unlock_irqrestore(&udc->lock, flags);
999
1000 return 0;
1001 }
1002
1003 static int omap_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
1004 {
1005 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep);
1006 struct omap_req *req;
1007 unsigned long flags;
1008
1009 if (!_ep || !_req)
1010 return -EINVAL;
1011
1012 spin_lock_irqsave(&ep->udc->lock, flags);
1013
1014 /* make sure it's actually queued on this endpoint */
1015 list_for_each_entry(req, &ep->queue, queue) {
1016 if (&req->req == _req)
1017 break;
1018 }
1019 if (&req->req != _req) {
1020 spin_unlock_irqrestore(&ep->udc->lock, flags);
1021 return -EINVAL;
1022 }
1023
1024 if (use_dma && ep->dma_channel && ep->queue.next == &req->queue) {
1025 int channel = ep->dma_channel;
1026
1027 /* releasing the channel cancels the request,
1028 * reclaiming the channel restarts the queue
1029 */
1030 dma_channel_release(ep);
1031 dma_channel_claim(ep, channel);
1032 } else
1033 done(ep, req, -ECONNRESET);
1034 spin_unlock_irqrestore(&ep->udc->lock, flags);
1035 return 0;
1036 }
1037
1038 /*-------------------------------------------------------------------------*/
1039
1040 static int omap_ep_set_halt(struct usb_ep *_ep, int value)
1041 {
1042 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep);
1043 unsigned long flags;
1044 int status = -EOPNOTSUPP;
1045
1046 spin_lock_irqsave(&ep->udc->lock, flags);
1047
1048 /* just use protocol stalls for ep0; real halts are annoying */
1049 if (ep->bEndpointAddress == 0) {
1050 if (!ep->udc->ep0_pending)
1051 status = -EINVAL;
1052 else if (value) {
1053 if (ep->udc->ep0_set_config) {
1054 WARNING("error changing config?\n");
1055 omap_writew(UDC_CLR_CFG, UDC_SYSCON2);
1056 }
1057 omap_writew(UDC_STALL_CMD, UDC_SYSCON2);
1058 ep->udc->ep0_pending = 0;
1059 status = 0;
1060 } else /* NOP */
1061 status = 0;
1062
1063 /* otherwise, all active non-ISO endpoints can halt */
1064 } else if (ep->bmAttributes != USB_ENDPOINT_XFER_ISOC && ep->ep.desc) {
1065
1066 /* IN endpoints must already be idle */
1067 if ((ep->bEndpointAddress & USB_DIR_IN)
1068 && !list_empty(&ep->queue)) {
1069 status = -EAGAIN;
1070 goto done;
1071 }
1072
1073 if (value) {
1074 int channel;
1075
1076 if (use_dma && ep->dma_channel
1077 && !list_empty(&ep->queue)) {
1078 channel = ep->dma_channel;
1079 dma_channel_release(ep);
1080 } else
1081 channel = 0;
1082
1083 use_ep(ep, UDC_EP_SEL);
1084 if (omap_readw(UDC_STAT_FLG) & UDC_NON_ISO_FIFO_EMPTY) {
1085 omap_writew(UDC_SET_HALT, UDC_CTRL);
1086 status = 0;
1087 } else
1088 status = -EAGAIN;
1089 deselect_ep();
1090
1091 if (channel)
1092 dma_channel_claim(ep, channel);
1093 } else {
1094 use_ep(ep, 0);
1095 omap_writew(ep->udc->clr_halt, UDC_CTRL);
1096 ep->ackwait = 0;
1097 if (!(ep->bEndpointAddress & USB_DIR_IN)) {
1098 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1099 ep->ackwait = 1 + ep->double_buf;
1100 }
1101 }
1102 }
1103 done:
1104 VDBG("%s %s halt stat %d\n", ep->ep.name,
1105 value ? "set" : "clear", status);
1106
1107 spin_unlock_irqrestore(&ep->udc->lock, flags);
1108 return status;
1109 }
1110
1111 static const struct usb_ep_ops omap_ep_ops = {
1112 .enable = omap_ep_enable,
1113 .disable = omap_ep_disable,
1114
1115 .alloc_request = omap_alloc_request,
1116 .free_request = omap_free_request,
1117
1118 .queue = omap_ep_queue,
1119 .dequeue = omap_ep_dequeue,
1120
1121 .set_halt = omap_ep_set_halt,
1122 /* fifo_status ... report bytes in fifo */
1123 /* fifo_flush ... flush fifo */
1124 };
1125
1126 /*-------------------------------------------------------------------------*/
1127
1128 static int omap_get_frame(struct usb_gadget *gadget)
1129 {
1130 u16 sof = omap_readw(UDC_SOF);
1131 return (sof & UDC_TS_OK) ? (sof & UDC_TS) : -EL2NSYNC;
1132 }
1133
1134 static int omap_wakeup(struct usb_gadget *gadget)
1135 {
1136 struct omap_udc *udc;
1137 unsigned long flags;
1138 int retval = -EHOSTUNREACH;
1139
1140 udc = container_of(gadget, struct omap_udc, gadget);
1141
1142 spin_lock_irqsave(&udc->lock, flags);
1143 if (udc->devstat & UDC_SUS) {
1144 /* NOTE: OTG spec erratum says that OTG devices may
1145 * issue wakeups without host enable.
1146 */
1147 if (udc->devstat & (UDC_B_HNP_ENABLE|UDC_R_WK_OK)) {
1148 DBG("remote wakeup...\n");
1149 omap_writew(UDC_RMT_WKP, UDC_SYSCON2);
1150 retval = 0;
1151 }
1152
1153 /* NOTE: non-OTG systems may use SRP TOO... */
1154 } else if (!(udc->devstat & UDC_ATT)) {
1155 if (!IS_ERR_OR_NULL(udc->transceiver))
1156 retval = otg_start_srp(udc->transceiver->otg);
1157 }
1158 spin_unlock_irqrestore(&udc->lock, flags);
1159
1160 return retval;
1161 }
1162
1163 static int
1164 omap_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered)
1165 {
1166 struct omap_udc *udc;
1167 unsigned long flags;
1168 u16 syscon1;
1169
1170 gadget->is_selfpowered = (is_selfpowered != 0);
1171 udc = container_of(gadget, struct omap_udc, gadget);
1172 spin_lock_irqsave(&udc->lock, flags);
1173 syscon1 = omap_readw(UDC_SYSCON1);
1174 if (is_selfpowered)
1175 syscon1 |= UDC_SELF_PWR;
1176 else
1177 syscon1 &= ~UDC_SELF_PWR;
1178 omap_writew(syscon1, UDC_SYSCON1);
1179 spin_unlock_irqrestore(&udc->lock, flags);
1180
1181 return 0;
1182 }
1183
1184 static int can_pullup(struct omap_udc *udc)
1185 {
1186 return udc->driver && udc->softconnect && udc->vbus_active;
1187 }
1188
1189 static void pullup_enable(struct omap_udc *udc)
1190 {
1191 u16 w;
1192
1193 w = omap_readw(UDC_SYSCON1);
1194 w |= UDC_PULLUP_EN;
1195 omap_writew(w, UDC_SYSCON1);
1196 if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) {
1197 u32 l;
1198
1199 l = omap_readl(OTG_CTRL);
1200 l |= OTG_BSESSVLD;
1201 omap_writel(l, OTG_CTRL);
1202 }
1203 omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN);
1204 }
1205
1206 static void pullup_disable(struct omap_udc *udc)
1207 {
1208 u16 w;
1209
1210 if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) {
1211 u32 l;
1212
1213 l = omap_readl(OTG_CTRL);
1214 l &= ~OTG_BSESSVLD;
1215 omap_writel(l, OTG_CTRL);
1216 }
1217 omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN);
1218 w = omap_readw(UDC_SYSCON1);
1219 w &= ~UDC_PULLUP_EN;
1220 omap_writew(w, UDC_SYSCON1);
1221 }
1222
1223 static struct omap_udc *udc;
1224
1225 static void omap_udc_enable_clock(int enable)
1226 {
1227 if (udc == NULL || udc->dc_clk == NULL || udc->hhc_clk == NULL)
1228 return;
1229
1230 if (enable) {
1231 clk_enable(udc->dc_clk);
1232 clk_enable(udc->hhc_clk);
1233 udelay(100);
1234 } else {
1235 clk_disable(udc->hhc_clk);
1236 clk_disable(udc->dc_clk);
1237 }
1238 }
1239
1240 /*
1241 * Called by whatever detects VBUS sessions: external transceiver
1242 * driver, or maybe GPIO0 VBUS IRQ. May request 48 MHz clock.
1243 */
1244 static int omap_vbus_session(struct usb_gadget *gadget, int is_active)
1245 {
1246 struct omap_udc *udc;
1247 unsigned long flags;
1248 u32 l;
1249
1250 udc = container_of(gadget, struct omap_udc, gadget);
1251 spin_lock_irqsave(&udc->lock, flags);
1252 VDBG("VBUS %s\n", is_active ? "on" : "off");
1253 udc->vbus_active = (is_active != 0);
1254 if (cpu_is_omap15xx()) {
1255 /* "software" detect, ignored if !VBUS_MODE_1510 */
1256 l = omap_readl(FUNC_MUX_CTRL_0);
1257 if (is_active)
1258 l |= VBUS_CTRL_1510;
1259 else
1260 l &= ~VBUS_CTRL_1510;
1261 omap_writel(l, FUNC_MUX_CTRL_0);
1262 }
1263 if (udc->dc_clk != NULL && is_active) {
1264 if (!udc->clk_requested) {
1265 omap_udc_enable_clock(1);
1266 udc->clk_requested = 1;
1267 }
1268 }
1269 if (can_pullup(udc))
1270 pullup_enable(udc);
1271 else
1272 pullup_disable(udc);
1273 if (udc->dc_clk != NULL && !is_active) {
1274 if (udc->clk_requested) {
1275 omap_udc_enable_clock(0);
1276 udc->clk_requested = 0;
1277 }
1278 }
1279 spin_unlock_irqrestore(&udc->lock, flags);
1280 return 0;
1281 }
1282
1283 static int omap_vbus_draw(struct usb_gadget *gadget, unsigned mA)
1284 {
1285 struct omap_udc *udc;
1286
1287 udc = container_of(gadget, struct omap_udc, gadget);
1288 if (!IS_ERR_OR_NULL(udc->transceiver))
1289 return usb_phy_set_power(udc->transceiver, mA);
1290 return -EOPNOTSUPP;
1291 }
1292
1293 static int omap_pullup(struct usb_gadget *gadget, int is_on)
1294 {
1295 struct omap_udc *udc;
1296 unsigned long flags;
1297
1298 udc = container_of(gadget, struct omap_udc, gadget);
1299 spin_lock_irqsave(&udc->lock, flags);
1300 udc->softconnect = (is_on != 0);
1301 if (can_pullup(udc))
1302 pullup_enable(udc);
1303 else
1304 pullup_disable(udc);
1305 spin_unlock_irqrestore(&udc->lock, flags);
1306 return 0;
1307 }
1308
1309 static int omap_udc_start(struct usb_gadget *g,
1310 struct usb_gadget_driver *driver);
1311 static int omap_udc_stop(struct usb_gadget *g);
1312
1313 static const struct usb_gadget_ops omap_gadget_ops = {
1314 .get_frame = omap_get_frame,
1315 .wakeup = omap_wakeup,
1316 .set_selfpowered = omap_set_selfpowered,
1317 .vbus_session = omap_vbus_session,
1318 .vbus_draw = omap_vbus_draw,
1319 .pullup = omap_pullup,
1320 .udc_start = omap_udc_start,
1321 .udc_stop = omap_udc_stop,
1322 };
1323
1324 /*-------------------------------------------------------------------------*/
1325
1326 /* dequeue ALL requests; caller holds udc->lock */
1327 static void nuke(struct omap_ep *ep, int status)
1328 {
1329 struct omap_req *req;
1330
1331 ep->stopped = 1;
1332
1333 if (use_dma && ep->dma_channel)
1334 dma_channel_release(ep);
1335
1336 use_ep(ep, 0);
1337 omap_writew(UDC_CLR_EP, UDC_CTRL);
1338 if (ep->bEndpointAddress && ep->bmAttributes != USB_ENDPOINT_XFER_ISOC)
1339 omap_writew(UDC_SET_HALT, UDC_CTRL);
1340
1341 while (!list_empty(&ep->queue)) {
1342 req = list_entry(ep->queue.next, struct omap_req, queue);
1343 done(ep, req, status);
1344 }
1345 }
1346
1347 /* caller holds udc->lock */
1348 static void udc_quiesce(struct omap_udc *udc)
1349 {
1350 struct omap_ep *ep;
1351
1352 udc->gadget.speed = USB_SPEED_UNKNOWN;
1353 nuke(&udc->ep[0], -ESHUTDOWN);
1354 list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list)
1355 nuke(ep, -ESHUTDOWN);
1356 }
1357
1358 /*-------------------------------------------------------------------------*/
1359
1360 static void update_otg(struct omap_udc *udc)
1361 {
1362 u16 devstat;
1363
1364 if (!gadget_is_otg(&udc->gadget))
1365 return;
1366
1367 if (omap_readl(OTG_CTRL) & OTG_ID)
1368 devstat = omap_readw(UDC_DEVSTAT);
1369 else
1370 devstat = 0;
1371
1372 udc->gadget.b_hnp_enable = !!(devstat & UDC_B_HNP_ENABLE);
1373 udc->gadget.a_hnp_support = !!(devstat & UDC_A_HNP_SUPPORT);
1374 udc->gadget.a_alt_hnp_support = !!(devstat & UDC_A_ALT_HNP_SUPPORT);
1375
1376 /* Enable HNP early, avoiding races on suspend irq path.
1377 * ASSUMES OTG state machine B_BUS_REQ input is true.
1378 */
1379 if (udc->gadget.b_hnp_enable) {
1380 u32 l;
1381
1382 l = omap_readl(OTG_CTRL);
1383 l |= OTG_B_HNPEN | OTG_B_BUSREQ;
1384 l &= ~OTG_PULLUP;
1385 omap_writel(l, OTG_CTRL);
1386 }
1387 }
1388
1389 static void ep0_irq(struct omap_udc *udc, u16 irq_src)
1390 {
1391 struct omap_ep *ep0 = &udc->ep[0];
1392 struct omap_req *req = NULL;
1393
1394 ep0->irqs++;
1395
1396 /* Clear any pending requests and then scrub any rx/tx state
1397 * before starting to handle the SETUP request.
1398 */
1399 if (irq_src & UDC_SETUP) {
1400 u16 ack = irq_src & (UDC_EP0_TX|UDC_EP0_RX);
1401
1402 nuke(ep0, 0);
1403 if (ack) {
1404 omap_writew(ack, UDC_IRQ_SRC);
1405 irq_src = UDC_SETUP;
1406 }
1407 }
1408
1409 /* IN/OUT packets mean we're in the DATA or STATUS stage.
1410 * This driver uses only uses protocol stalls (ep0 never halts),
1411 * and if we got this far the gadget driver already had a
1412 * chance to stall. Tries to be forgiving of host oddities.
1413 *
1414 * NOTE: the last chance gadget drivers have to stall control
1415 * requests is during their request completion callback.
1416 */
1417 if (!list_empty(&ep0->queue))
1418 req = container_of(ep0->queue.next, struct omap_req, queue);
1419
1420 /* IN == TX to host */
1421 if (irq_src & UDC_EP0_TX) {
1422 int stat;
1423
1424 omap_writew(UDC_EP0_TX, UDC_IRQ_SRC);
1425 omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM);
1426 stat = omap_readw(UDC_STAT_FLG);
1427 if (stat & UDC_ACK) {
1428 if (udc->ep0_in) {
1429 /* write next IN packet from response,
1430 * or set up the status stage.
1431 */
1432 if (req)
1433 stat = write_fifo(ep0, req);
1434 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1435 if (!req && udc->ep0_pending) {
1436 omap_writew(UDC_EP_SEL, UDC_EP_NUM);
1437 omap_writew(UDC_CLR_EP, UDC_CTRL);
1438 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1439 omap_writew(0, UDC_EP_NUM);
1440 udc->ep0_pending = 0;
1441 } /* else: 6 wait states before it'll tx */
1442 } else {
1443 /* ack status stage of OUT transfer */
1444 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1445 if (req)
1446 done(ep0, req, 0);
1447 }
1448 req = NULL;
1449 } else if (stat & UDC_STALL) {
1450 omap_writew(UDC_CLR_HALT, UDC_CTRL);
1451 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1452 } else {
1453 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1454 }
1455 }
1456
1457 /* OUT == RX from host */
1458 if (irq_src & UDC_EP0_RX) {
1459 int stat;
1460
1461 omap_writew(UDC_EP0_RX, UDC_IRQ_SRC);
1462 omap_writew(UDC_EP_SEL, UDC_EP_NUM);
1463 stat = omap_readw(UDC_STAT_FLG);
1464 if (stat & UDC_ACK) {
1465 if (!udc->ep0_in) {
1466 stat = 0;
1467 /* read next OUT packet of request, maybe
1468 * reactiviting the fifo; stall on errors.
1469 */
1470 stat = read_fifo(ep0, req);
1471 if (!req || stat < 0) {
1472 omap_writew(UDC_STALL_CMD, UDC_SYSCON2);
1473 udc->ep0_pending = 0;
1474 stat = 0;
1475 } else if (stat == 0)
1476 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1477 omap_writew(0, UDC_EP_NUM);
1478
1479 /* activate status stage */
1480 if (stat == 1) {
1481 done(ep0, req, 0);
1482 /* that may have STALLed ep0... */
1483 omap_writew(UDC_EP_SEL | UDC_EP_DIR,
1484 UDC_EP_NUM);
1485 omap_writew(UDC_CLR_EP, UDC_CTRL);
1486 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1487 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1488 udc->ep0_pending = 0;
1489 }
1490 } else {
1491 /* ack status stage of IN transfer */
1492 omap_writew(0, UDC_EP_NUM);
1493 if (req)
1494 done(ep0, req, 0);
1495 }
1496 } else if (stat & UDC_STALL) {
1497 omap_writew(UDC_CLR_HALT, UDC_CTRL);
1498 omap_writew(0, UDC_EP_NUM);
1499 } else {
1500 omap_writew(0, UDC_EP_NUM);
1501 }
1502 }
1503
1504 /* SETUP starts all control transfers */
1505 if (irq_src & UDC_SETUP) {
1506 union u {
1507 u16 word[4];
1508 struct usb_ctrlrequest r;
1509 } u;
1510 int status = -EINVAL;
1511 struct omap_ep *ep;
1512
1513 /* read the (latest) SETUP message */
1514 do {
1515 omap_writew(UDC_SETUP_SEL, UDC_EP_NUM);
1516 /* two bytes at a time */
1517 u.word[0] = omap_readw(UDC_DATA);
1518 u.word[1] = omap_readw(UDC_DATA);
1519 u.word[2] = omap_readw(UDC_DATA);
1520 u.word[3] = omap_readw(UDC_DATA);
1521 omap_writew(0, UDC_EP_NUM);
1522 } while (omap_readw(UDC_IRQ_SRC) & UDC_SETUP);
1523
1524 #define w_value le16_to_cpu(u.r.wValue)
1525 #define w_index le16_to_cpu(u.r.wIndex)
1526 #define w_length le16_to_cpu(u.r.wLength)
1527
1528 /* Delegate almost all control requests to the gadget driver,
1529 * except for a handful of ch9 status/feature requests that
1530 * hardware doesn't autodecode _and_ the gadget API hides.
1531 */
1532 udc->ep0_in = (u.r.bRequestType & USB_DIR_IN) != 0;
1533 udc->ep0_set_config = 0;
1534 udc->ep0_pending = 1;
1535 ep0->stopped = 0;
1536 ep0->ackwait = 0;
1537 switch (u.r.bRequest) {
1538 case USB_REQ_SET_CONFIGURATION:
1539 /* udc needs to know when ep != 0 is valid */
1540 if (u.r.bRequestType != USB_RECIP_DEVICE)
1541 goto delegate;
1542 if (w_length != 0)
1543 goto do_stall;
1544 udc->ep0_set_config = 1;
1545 udc->ep0_reset_config = (w_value == 0);
1546 VDBG("set config %d\n", w_value);
1547
1548 /* update udc NOW since gadget driver may start
1549 * queueing requests immediately; clear config
1550 * later if it fails the request.
1551 */
1552 if (udc->ep0_reset_config)
1553 omap_writew(UDC_CLR_CFG, UDC_SYSCON2);
1554 else
1555 omap_writew(UDC_DEV_CFG, UDC_SYSCON2);
1556 update_otg(udc);
1557 goto delegate;
1558 case USB_REQ_CLEAR_FEATURE:
1559 /* clear endpoint halt */
1560 if (u.r.bRequestType != USB_RECIP_ENDPOINT)
1561 goto delegate;
1562 if (w_value != USB_ENDPOINT_HALT
1563 || w_length != 0)
1564 goto do_stall;
1565 ep = &udc->ep[w_index & 0xf];
1566 if (ep != ep0) {
1567 if (w_index & USB_DIR_IN)
1568 ep += 16;
1569 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
1570 || !ep->ep.desc)
1571 goto do_stall;
1572 use_ep(ep, 0);
1573 omap_writew(udc->clr_halt, UDC_CTRL);
1574 ep->ackwait = 0;
1575 if (!(ep->bEndpointAddress & USB_DIR_IN)) {
1576 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1577 ep->ackwait = 1 + ep->double_buf;
1578 }
1579 /* NOTE: assumes the host behaves sanely,
1580 * only clearing real halts. Else we may
1581 * need to kill pending transfers and then
1582 * restart the queue... very messy for DMA!
1583 */
1584 }
1585 VDBG("%s halt cleared by host\n", ep->name);
1586 goto ep0out_status_stage;
1587 case USB_REQ_SET_FEATURE:
1588 /* set endpoint halt */
1589 if (u.r.bRequestType != USB_RECIP_ENDPOINT)
1590 goto delegate;
1591 if (w_value != USB_ENDPOINT_HALT
1592 || w_length != 0)
1593 goto do_stall;
1594 ep = &udc->ep[w_index & 0xf];
1595 if (w_index & USB_DIR_IN)
1596 ep += 16;
1597 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
1598 || ep == ep0 || !ep->ep.desc)
1599 goto do_stall;
1600 if (use_dma && ep->has_dma) {
1601 /* this has rude side-effects (aborts) and
1602 * can't really work if DMA-IN is active
1603 */
1604 DBG("%s host set_halt, NYET\n", ep->name);
1605 goto do_stall;
1606 }
1607 use_ep(ep, 0);
1608 /* can't halt if fifo isn't empty... */
1609 omap_writew(UDC_CLR_EP, UDC_CTRL);
1610 omap_writew(UDC_SET_HALT, UDC_CTRL);
1611 VDBG("%s halted by host\n", ep->name);
1612 ep0out_status_stage:
1613 status = 0;
1614 omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM);
1615 omap_writew(UDC_CLR_EP, UDC_CTRL);
1616 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1617 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1618 udc->ep0_pending = 0;
1619 break;
1620 case USB_REQ_GET_STATUS:
1621 /* USB_ENDPOINT_HALT status? */
1622 if (u.r.bRequestType != (USB_DIR_IN|USB_RECIP_ENDPOINT))
1623 goto intf_status;
1624
1625 /* ep0 never stalls */
1626 if (!(w_index & 0xf))
1627 goto zero_status;
1628
1629 /* only active endpoints count */
1630 ep = &udc->ep[w_index & 0xf];
1631 if (w_index & USB_DIR_IN)
1632 ep += 16;
1633 if (!ep->ep.desc)
1634 goto do_stall;
1635
1636 /* iso never stalls */
1637 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC)
1638 goto zero_status;
1639
1640 /* FIXME don't assume non-halted endpoints!! */
1641 ERR("%s status, can't report\n", ep->ep.name);
1642 goto do_stall;
1643
1644 intf_status:
1645 /* return interface status. if we were pedantic,
1646 * we'd detect non-existent interfaces, and stall.
1647 */
1648 if (u.r.bRequestType
1649 != (USB_DIR_IN|USB_RECIP_INTERFACE))
1650 goto delegate;
1651
1652 zero_status:
1653 /* return two zero bytes */
1654 omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM);
1655 omap_writew(0, UDC_DATA);
1656 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1657 omap_writew(UDC_EP_DIR, UDC_EP_NUM);
1658 status = 0;
1659 VDBG("GET_STATUS, interface %d\n", w_index);
1660 /* next, status stage */
1661 break;
1662 default:
1663 delegate:
1664 /* activate the ep0out fifo right away */
1665 if (!udc->ep0_in && w_length) {
1666 omap_writew(0, UDC_EP_NUM);
1667 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1668 }
1669
1670 /* gadget drivers see class/vendor specific requests,
1671 * {SET,GET}_{INTERFACE,DESCRIPTOR,CONFIGURATION},
1672 * and more
1673 */
1674 VDBG("SETUP %02x.%02x v%04x i%04x l%04x\n",
1675 u.r.bRequestType, u.r.bRequest,
1676 w_value, w_index, w_length);
1677
1678 #undef w_value
1679 #undef w_index
1680 #undef w_length
1681
1682 /* The gadget driver may return an error here,
1683 * causing an immediate protocol stall.
1684 *
1685 * Else it must issue a response, either queueing a
1686 * response buffer for the DATA stage, or halting ep0
1687 * (causing a protocol stall, not a real halt). A
1688 * zero length buffer means no DATA stage.
1689 *
1690 * It's fine to issue that response after the setup()
1691 * call returns, and this IRQ was handled.
1692 */
1693 udc->ep0_setup = 1;
1694 spin_unlock(&udc->lock);
1695 status = udc->driver->setup(&udc->gadget, &u.r);
1696 spin_lock(&udc->lock);
1697 udc->ep0_setup = 0;
1698 }
1699
1700 if (status < 0) {
1701 do_stall:
1702 VDBG("req %02x.%02x protocol STALL; stat %d\n",
1703 u.r.bRequestType, u.r.bRequest, status);
1704 if (udc->ep0_set_config) {
1705 if (udc->ep0_reset_config)
1706 WARNING("error resetting config?\n");
1707 else
1708 omap_writew(UDC_CLR_CFG, UDC_SYSCON2);
1709 }
1710 omap_writew(UDC_STALL_CMD, UDC_SYSCON2);
1711 udc->ep0_pending = 0;
1712 }
1713 }
1714 }
1715
1716 /*-------------------------------------------------------------------------*/
1717
1718 #define OTG_FLAGS (UDC_B_HNP_ENABLE|UDC_A_HNP_SUPPORT|UDC_A_ALT_HNP_SUPPORT)
1719
1720 static void devstate_irq(struct omap_udc *udc, u16 irq_src)
1721 {
1722 u16 devstat, change;
1723
1724 devstat = omap_readw(UDC_DEVSTAT);
1725 change = devstat ^ udc->devstat;
1726 udc->devstat = devstat;
1727
1728 if (change & (UDC_USB_RESET|UDC_ATT)) {
1729 udc_quiesce(udc);
1730
1731 if (change & UDC_ATT) {
1732 /* driver for any external transceiver will
1733 * have called omap_vbus_session() already
1734 */
1735 if (devstat & UDC_ATT) {
1736 udc->gadget.speed = USB_SPEED_FULL;
1737 VDBG("connect\n");
1738 if (IS_ERR_OR_NULL(udc->transceiver))
1739 pullup_enable(udc);
1740 /* if (driver->connect) call it */
1741 } else if (udc->gadget.speed != USB_SPEED_UNKNOWN) {
1742 udc->gadget.speed = USB_SPEED_UNKNOWN;
1743 if (IS_ERR_OR_NULL(udc->transceiver))
1744 pullup_disable(udc);
1745 DBG("disconnect, gadget %s\n",
1746 udc->driver->driver.name);
1747 if (udc->driver->disconnect) {
1748 spin_unlock(&udc->lock);
1749 udc->driver->disconnect(&udc->gadget);
1750 spin_lock(&udc->lock);
1751 }
1752 }
1753 change &= ~UDC_ATT;
1754 }
1755
1756 if (change & UDC_USB_RESET) {
1757 if (devstat & UDC_USB_RESET) {
1758 VDBG("RESET=1\n");
1759 } else {
1760 udc->gadget.speed = USB_SPEED_FULL;
1761 INFO("USB reset done, gadget %s\n",
1762 udc->driver->driver.name);
1763 /* ep0 traffic is legal from now on */
1764 omap_writew(UDC_DS_CHG_IE | UDC_EP0_IE,
1765 UDC_IRQ_EN);
1766 }
1767 change &= ~UDC_USB_RESET;
1768 }
1769 }
1770 if (change & UDC_SUS) {
1771 if (udc->gadget.speed != USB_SPEED_UNKNOWN) {
1772 /* FIXME tell isp1301 to suspend/resume (?) */
1773 if (devstat & UDC_SUS) {
1774 VDBG("suspend\n");
1775 update_otg(udc);
1776 /* HNP could be under way already */
1777 if (udc->gadget.speed == USB_SPEED_FULL
1778 && udc->driver->suspend) {
1779 spin_unlock(&udc->lock);
1780 udc->driver->suspend(&udc->gadget);
1781 spin_lock(&udc->lock);
1782 }
1783 if (!IS_ERR_OR_NULL(udc->transceiver))
1784 usb_phy_set_suspend(
1785 udc->transceiver, 1);
1786 } else {
1787 VDBG("resume\n");
1788 if (!IS_ERR_OR_NULL(udc->transceiver))
1789 usb_phy_set_suspend(
1790 udc->transceiver, 0);
1791 if (udc->gadget.speed == USB_SPEED_FULL
1792 && udc->driver->resume) {
1793 spin_unlock(&udc->lock);
1794 udc->driver->resume(&udc->gadget);
1795 spin_lock(&udc->lock);
1796 }
1797 }
1798 }
1799 change &= ~UDC_SUS;
1800 }
1801 if (!cpu_is_omap15xx() && (change & OTG_FLAGS)) {
1802 update_otg(udc);
1803 change &= ~OTG_FLAGS;
1804 }
1805
1806 change &= ~(UDC_CFG|UDC_DEF|UDC_ADD);
1807 if (change)
1808 VDBG("devstat %03x, ignore change %03x\n",
1809 devstat, change);
1810
1811 omap_writew(UDC_DS_CHG, UDC_IRQ_SRC);
1812 }
1813
1814 static irqreturn_t omap_udc_irq(int irq, void *_udc)
1815 {
1816 struct omap_udc *udc = _udc;
1817 u16 irq_src;
1818 irqreturn_t status = IRQ_NONE;
1819 unsigned long flags;
1820
1821 spin_lock_irqsave(&udc->lock, flags);
1822 irq_src = omap_readw(UDC_IRQ_SRC);
1823
1824 /* Device state change (usb ch9 stuff) */
1825 if (irq_src & UDC_DS_CHG) {
1826 devstate_irq(_udc, irq_src);
1827 status = IRQ_HANDLED;
1828 irq_src &= ~UDC_DS_CHG;
1829 }
1830
1831 /* EP0 control transfers */
1832 if (irq_src & (UDC_EP0_RX|UDC_SETUP|UDC_EP0_TX)) {
1833 ep0_irq(_udc, irq_src);
1834 status = IRQ_HANDLED;
1835 irq_src &= ~(UDC_EP0_RX|UDC_SETUP|UDC_EP0_TX);
1836 }
1837
1838 /* DMA transfer completion */
1839 if (use_dma && (irq_src & (UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT))) {
1840 dma_irq(_udc, irq_src);
1841 status = IRQ_HANDLED;
1842 irq_src &= ~(UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT);
1843 }
1844
1845 irq_src &= ~(UDC_IRQ_SOF | UDC_EPN_TX|UDC_EPN_RX);
1846 if (irq_src)
1847 DBG("udc_irq, unhandled %03x\n", irq_src);
1848 spin_unlock_irqrestore(&udc->lock, flags);
1849
1850 return status;
1851 }
1852
1853 /* workaround for seemingly-lost IRQs for RX ACKs... */
1854 #define PIO_OUT_TIMEOUT (jiffies + HZ/3)
1855 #define HALF_FULL(f) (!((f)&(UDC_NON_ISO_FIFO_FULL|UDC_NON_ISO_FIFO_EMPTY)))
1856
1857 static void pio_out_timer(struct timer_list *t)
1858 {
1859 struct omap_ep *ep = from_timer(ep, t, timer);
1860 unsigned long flags;
1861 u16 stat_flg;
1862
1863 spin_lock_irqsave(&ep->udc->lock, flags);
1864 if (!list_empty(&ep->queue) && ep->ackwait) {
1865 use_ep(ep, UDC_EP_SEL);
1866 stat_flg = omap_readw(UDC_STAT_FLG);
1867
1868 if ((stat_flg & UDC_ACK) && (!(stat_flg & UDC_FIFO_EN)
1869 || (ep->double_buf && HALF_FULL(stat_flg)))) {
1870 struct omap_req *req;
1871
1872 VDBG("%s: lose, %04x\n", ep->ep.name, stat_flg);
1873 req = container_of(ep->queue.next,
1874 struct omap_req, queue);
1875 (void) read_fifo(ep, req);
1876 omap_writew(ep->bEndpointAddress, UDC_EP_NUM);
1877 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1878 ep->ackwait = 1 + ep->double_buf;
1879 } else
1880 deselect_ep();
1881 }
1882 mod_timer(&ep->timer, PIO_OUT_TIMEOUT);
1883 spin_unlock_irqrestore(&ep->udc->lock, flags);
1884 }
1885
1886 static irqreturn_t omap_udc_pio_irq(int irq, void *_dev)
1887 {
1888 u16 epn_stat, irq_src;
1889 irqreturn_t status = IRQ_NONE;
1890 struct omap_ep *ep;
1891 int epnum;
1892 struct omap_udc *udc = _dev;
1893 struct omap_req *req;
1894 unsigned long flags;
1895
1896 spin_lock_irqsave(&udc->lock, flags);
1897 epn_stat = omap_readw(UDC_EPN_STAT);
1898 irq_src = omap_readw(UDC_IRQ_SRC);
1899
1900 /* handle OUT first, to avoid some wasteful NAKs */
1901 if (irq_src & UDC_EPN_RX) {
1902 epnum = (epn_stat >> 8) & 0x0f;
1903 omap_writew(UDC_EPN_RX, UDC_IRQ_SRC);
1904 status = IRQ_HANDLED;
1905 ep = &udc->ep[epnum];
1906 ep->irqs++;
1907
1908 omap_writew(epnum | UDC_EP_SEL, UDC_EP_NUM);
1909 ep->fnf = 0;
1910 if (omap_readw(UDC_STAT_FLG) & UDC_ACK) {
1911 ep->ackwait--;
1912 if (!list_empty(&ep->queue)) {
1913 int stat;
1914 req = container_of(ep->queue.next,
1915 struct omap_req, queue);
1916 stat = read_fifo(ep, req);
1917 if (!ep->double_buf)
1918 ep->fnf = 1;
1919 }
1920 }
1921 /* min 6 clock delay before clearing EP_SEL ... */
1922 epn_stat = omap_readw(UDC_EPN_STAT);
1923 epn_stat = omap_readw(UDC_EPN_STAT);
1924 omap_writew(epnum, UDC_EP_NUM);
1925
1926 /* enabling fifo _after_ clearing ACK, contrary to docs,
1927 * reduces lossage; timer still needed though (sigh).
1928 */
1929 if (ep->fnf) {
1930 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL);
1931 ep->ackwait = 1 + ep->double_buf;
1932 }
1933 mod_timer(&ep->timer, PIO_OUT_TIMEOUT);
1934 }
1935
1936 /* then IN transfers */
1937 else if (irq_src & UDC_EPN_TX) {
1938 epnum = epn_stat & 0x0f;
1939 omap_writew(UDC_EPN_TX, UDC_IRQ_SRC);
1940 status = IRQ_HANDLED;
1941 ep = &udc->ep[16 + epnum];
1942 ep->irqs++;
1943
1944 omap_writew(epnum | UDC_EP_DIR | UDC_EP_SEL, UDC_EP_NUM);
1945 if (omap_readw(UDC_STAT_FLG) & UDC_ACK) {
1946 ep->ackwait = 0;
1947 if (!list_empty(&ep->queue)) {
1948 req = container_of(ep->queue.next,
1949 struct omap_req, queue);
1950 (void) write_fifo(ep, req);
1951 }
1952 }
1953 /* min 6 clock delay before clearing EP_SEL ... */
1954 epn_stat = omap_readw(UDC_EPN_STAT);
1955 epn_stat = omap_readw(UDC_EPN_STAT);
1956 omap_writew(epnum | UDC_EP_DIR, UDC_EP_NUM);
1957 /* then 6 clocks before it'd tx */
1958 }
1959
1960 spin_unlock_irqrestore(&udc->lock, flags);
1961 return status;
1962 }
1963
1964 #ifdef USE_ISO
1965 static irqreturn_t omap_udc_iso_irq(int irq, void *_dev)
1966 {
1967 struct omap_udc *udc = _dev;
1968 struct omap_ep *ep;
1969 int pending = 0;
1970 unsigned long flags;
1971
1972 spin_lock_irqsave(&udc->lock, flags);
1973
1974 /* handle all non-DMA ISO transfers */
1975 list_for_each_entry(ep, &udc->iso, iso) {
1976 u16 stat;
1977 struct omap_req *req;
1978
1979 if (ep->has_dma || list_empty(&ep->queue))
1980 continue;
1981 req = list_entry(ep->queue.next, struct omap_req, queue);
1982
1983 use_ep(ep, UDC_EP_SEL);
1984 stat = omap_readw(UDC_STAT_FLG);
1985
1986 /* NOTE: like the other controller drivers, this isn't
1987 * currently reporting lost or damaged frames.
1988 */
1989 if (ep->bEndpointAddress & USB_DIR_IN) {
1990 if (stat & UDC_MISS_IN)
1991 /* done(ep, req, -EPROTO) */;
1992 else
1993 write_fifo(ep, req);
1994 } else {
1995 int status = 0;
1996
1997 if (stat & UDC_NO_RXPACKET)
1998 status = -EREMOTEIO;
1999 else if (stat & UDC_ISO_ERR)
2000 status = -EILSEQ;
2001 else if (stat & UDC_DATA_FLUSH)
2002 status = -ENOSR;
2003
2004 if (status)
2005 /* done(ep, req, status) */;
2006 else
2007 read_fifo(ep, req);
2008 }
2009 deselect_ep();
2010 /* 6 wait states before next EP */
2011
2012 ep->irqs++;
2013 if (!list_empty(&ep->queue))
2014 pending = 1;
2015 }
2016 if (!pending) {
2017 u16 w;
2018
2019 w = omap_readw(UDC_IRQ_EN);
2020 w &= ~UDC_SOF_IE;
2021 omap_writew(w, UDC_IRQ_EN);
2022 }
2023 omap_writew(UDC_IRQ_SOF, UDC_IRQ_SRC);
2024
2025 spin_unlock_irqrestore(&udc->lock, flags);
2026 return IRQ_HANDLED;
2027 }
2028 #endif
2029
2030 /*-------------------------------------------------------------------------*/
2031
2032 static inline int machine_without_vbus_sense(void)
2033 {
2034 return machine_is_omap_innovator()
2035 || machine_is_omap_osk()
2036 || machine_is_sx1()
2037 /* No known omap7xx boards with vbus sense */
2038 || cpu_is_omap7xx();
2039 }
2040
2041 static int omap_udc_start(struct usb_gadget *g,
2042 struct usb_gadget_driver *driver)
2043 {
2044 int status = -ENODEV;
2045 struct omap_ep *ep;
2046 unsigned long flags;
2047
2048
2049 spin_lock_irqsave(&udc->lock, flags);
2050 /* reset state */
2051 list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) {
2052 ep->irqs = 0;
2053 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC)
2054 continue;
2055 use_ep(ep, 0);
2056 omap_writew(UDC_SET_HALT, UDC_CTRL);
2057 }
2058 udc->ep0_pending = 0;
2059 udc->ep[0].irqs = 0;
2060 udc->softconnect = 1;
2061
2062 /* hook up the driver */
2063 driver->driver.bus = NULL;
2064 udc->driver = driver;
2065 spin_unlock_irqrestore(&udc->lock, flags);
2066
2067 if (udc->dc_clk != NULL)
2068 omap_udc_enable_clock(1);
2069
2070 omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC);
2071
2072 /* connect to bus through transceiver */
2073 if (!IS_ERR_OR_NULL(udc->transceiver)) {
2074 status = otg_set_peripheral(udc->transceiver->otg,
2075 &udc->gadget);
2076 if (status < 0) {
2077 ERR("can't bind to transceiver\n");
2078 udc->driver = NULL;
2079 goto done;
2080 }
2081 } else {
2082 if (can_pullup(udc))
2083 pullup_enable(udc);
2084 else
2085 pullup_disable(udc);
2086 }
2087
2088 /* boards that don't have VBUS sensing can't autogate 48MHz;
2089 * can't enter deep sleep while a gadget driver is active.
2090 */
2091 if (machine_without_vbus_sense())
2092 omap_vbus_session(&udc->gadget, 1);
2093
2094 done:
2095 if (udc->dc_clk != NULL)
2096 omap_udc_enable_clock(0);
2097
2098 return status;
2099 }
2100
2101 static int omap_udc_stop(struct usb_gadget *g)
2102 {
2103 unsigned long flags;
2104 int status = -ENODEV;
2105
2106 if (udc->dc_clk != NULL)
2107 omap_udc_enable_clock(1);
2108
2109 if (machine_without_vbus_sense())
2110 omap_vbus_session(&udc->gadget, 0);
2111
2112 if (!IS_ERR_OR_NULL(udc->transceiver))
2113 (void) otg_set_peripheral(udc->transceiver->otg, NULL);
2114 else
2115 pullup_disable(udc);
2116
2117 spin_lock_irqsave(&udc->lock, flags);
2118 udc_quiesce(udc);
2119 spin_unlock_irqrestore(&udc->lock, flags);
2120
2121 udc->driver = NULL;
2122
2123 if (udc->dc_clk != NULL)
2124 omap_udc_enable_clock(0);
2125
2126 return status;
2127 }
2128
2129 /*-------------------------------------------------------------------------*/
2130
2131 #ifdef CONFIG_USB_GADGET_DEBUG_FILES
2132
2133 #include <linux/seq_file.h>
2134
2135 static const char proc_filename[] = "driver/udc";
2136
2137 #define FOURBITS "%s%s%s%s"
2138 #define EIGHTBITS "%s%s%s%s%s%s%s%s"
2139
2140 static void proc_ep_show(struct seq_file *s, struct omap_ep *ep)
2141 {
2142 u16 stat_flg;
2143 struct omap_req *req;
2144 char buf[20];
2145
2146 use_ep(ep, 0);
2147
2148 if (use_dma && ep->has_dma)
2149 snprintf(buf, sizeof buf, "(%cxdma%d lch%d) ",
2150 (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r',
2151 ep->dma_channel - 1, ep->lch);
2152 else
2153 buf[0] = 0;
2154
2155 stat_flg = omap_readw(UDC_STAT_FLG);
2156 seq_printf(s,
2157 "\n%s %s%s%sirqs %ld stat %04x " EIGHTBITS FOURBITS "%s\n",
2158 ep->name, buf,
2159 ep->double_buf ? "dbuf " : "",
2160 ({ char *s;
2161 switch (ep->ackwait) {
2162 case 0:
2163 s = "";
2164 break;
2165 case 1:
2166 s = "(ackw) ";
2167 break;
2168 case 2:
2169 s = "(ackw2) ";
2170 break;
2171 default:
2172 s = "(?) ";
2173 break;
2174 } s; }),
2175 ep->irqs, stat_flg,
2176 (stat_flg & UDC_NO_RXPACKET) ? "no_rxpacket " : "",
2177 (stat_flg & UDC_MISS_IN) ? "miss_in " : "",
2178 (stat_flg & UDC_DATA_FLUSH) ? "data_flush " : "",
2179 (stat_flg & UDC_ISO_ERR) ? "iso_err " : "",
2180 (stat_flg & UDC_ISO_FIFO_EMPTY) ? "iso_fifo_empty " : "",
2181 (stat_flg & UDC_ISO_FIFO_FULL) ? "iso_fifo_full " : "",
2182 (stat_flg & UDC_EP_HALTED) ? "HALT " : "",
2183 (stat_flg & UDC_STALL) ? "STALL " : "",
2184 (stat_flg & UDC_NAK) ? "NAK " : "",
2185 (stat_flg & UDC_ACK) ? "ACK " : "",
2186 (stat_flg & UDC_FIFO_EN) ? "fifo_en " : "",
2187 (stat_flg & UDC_NON_ISO_FIFO_EMPTY) ? "fifo_empty " : "",
2188 (stat_flg & UDC_NON_ISO_FIFO_FULL) ? "fifo_full " : "");
2189
2190 if (list_empty(&ep->queue))
2191 seq_printf(s, "\t(queue empty)\n");
2192 else
2193 list_for_each_entry(req, &ep->queue, queue) {
2194 unsigned length = req->req.actual;
2195
2196 if (use_dma && buf[0]) {
2197 length += ((ep->bEndpointAddress & USB_DIR_IN)
2198 ? dma_src_len : dma_dest_len)
2199 (ep, req->req.dma + length);
2200 buf[0] = 0;
2201 }
2202 seq_printf(s, "\treq %p len %d/%d buf %p\n",
2203 &req->req, length,
2204 req->req.length, req->req.buf);
2205 }
2206 }
2207
2208 static char *trx_mode(unsigned m, int enabled)
2209 {
2210 switch (m) {
2211 case 0:
2212 return enabled ? "*6wire" : "unused";
2213 case 1:
2214 return "4wire";
2215 case 2:
2216 return "3wire";
2217 case 3:
2218 return "6wire";
2219 default:
2220 return "unknown";
2221 }
2222 }
2223
2224 static int proc_otg_show(struct seq_file *s)
2225 {
2226 u32 tmp;
2227 u32 trans = 0;
2228 char *ctrl_name = "(UNKNOWN)";
2229
2230 tmp = omap_readl(OTG_REV);
2231 ctrl_name = "tranceiver_ctrl";
2232 trans = omap_readw(USB_TRANSCEIVER_CTRL);
2233 seq_printf(s, "\nOTG rev %d.%d, %s %05x\n",
2234 tmp >> 4, tmp & 0xf, ctrl_name, trans);
2235 tmp = omap_readw(OTG_SYSCON_1);
2236 seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s,"
2237 FOURBITS "\n", tmp,
2238 trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R),
2239 trx_mode(USB1_TRX_MODE(tmp), trans & CONF_USB1_UNI_R),
2240 (USB0_TRX_MODE(tmp) == 0 && !cpu_is_omap1710())
2241 ? "internal"
2242 : trx_mode(USB0_TRX_MODE(tmp), 1),
2243 (tmp & OTG_IDLE_EN) ? " !otg" : "",
2244 (tmp & HST_IDLE_EN) ? " !host" : "",
2245 (tmp & DEV_IDLE_EN) ? " !dev" : "",
2246 (tmp & OTG_RESET_DONE) ? " reset_done" : " reset_active");
2247 tmp = omap_readl(OTG_SYSCON_2);
2248 seq_printf(s, "otg_syscon2 %08x%s" EIGHTBITS
2249 " b_ase_brst=%d hmc=%d\n", tmp,
2250 (tmp & OTG_EN) ? " otg_en" : "",
2251 (tmp & USBX_SYNCHRO) ? " synchro" : "",
2252 /* much more SRP stuff */
2253 (tmp & SRP_DATA) ? " srp_data" : "",
2254 (tmp & SRP_VBUS) ? " srp_vbus" : "",
2255 (tmp & OTG_PADEN) ? " otg_paden" : "",
2256 (tmp & HMC_PADEN) ? " hmc_paden" : "",
2257 (tmp & UHOST_EN) ? " uhost_en" : "",
2258 (tmp & HMC_TLLSPEED) ? " tllspeed" : "",
2259 (tmp & HMC_TLLATTACH) ? " tllattach" : "",
2260 B_ASE_BRST(tmp),
2261 OTG_HMC(tmp));
2262 tmp = omap_readl(OTG_CTRL);
2263 seq_printf(s, "otg_ctrl %06x" EIGHTBITS EIGHTBITS "%s\n", tmp,
2264 (tmp & OTG_ASESSVLD) ? " asess" : "",
2265 (tmp & OTG_BSESSEND) ? " bsess_end" : "",
2266 (tmp & OTG_BSESSVLD) ? " bsess" : "",
2267 (tmp & OTG_VBUSVLD) ? " vbus" : "",
2268 (tmp & OTG_ID) ? " id" : "",
2269 (tmp & OTG_DRIVER_SEL) ? " DEVICE" : " HOST",
2270 (tmp & OTG_A_SETB_HNPEN) ? " a_setb_hnpen" : "",
2271 (tmp & OTG_A_BUSREQ) ? " a_bus" : "",
2272 (tmp & OTG_B_HNPEN) ? " b_hnpen" : "",
2273 (tmp & OTG_B_BUSREQ) ? " b_bus" : "",
2274 (tmp & OTG_BUSDROP) ? " busdrop" : "",
2275 (tmp & OTG_PULLDOWN) ? " down" : "",
2276 (tmp & OTG_PULLUP) ? " up" : "",
2277 (tmp & OTG_DRV_VBUS) ? " drv" : "",
2278 (tmp & OTG_PD_VBUS) ? " pd_vb" : "",
2279 (tmp & OTG_PU_VBUS) ? " pu_vb" : "",
2280 (tmp & OTG_PU_ID) ? " pu_id" : ""
2281 );
2282 tmp = omap_readw(OTG_IRQ_EN);
2283 seq_printf(s, "otg_irq_en %04x" "\n", tmp);
2284 tmp = omap_readw(OTG_IRQ_SRC);
2285 seq_printf(s, "otg_irq_src %04x" "\n", tmp);
2286 tmp = omap_readw(OTG_OUTCTRL);
2287 seq_printf(s, "otg_outctrl %04x" "\n", tmp);
2288 tmp = omap_readw(OTG_TEST);
2289 seq_printf(s, "otg_test %04x" "\n", tmp);
2290 return 0;
2291 }
2292
2293 static int proc_udc_show(struct seq_file *s, void *_)
2294 {
2295 u32 tmp;
2296 struct omap_ep *ep;
2297 unsigned long flags;
2298
2299 spin_lock_irqsave(&udc->lock, flags);
2300
2301 seq_printf(s, "%s, version: " DRIVER_VERSION
2302 #ifdef USE_ISO
2303 " (iso)"
2304 #endif
2305 "%s\n",
2306 driver_desc,
2307 use_dma ? " (dma)" : "");
2308
2309 tmp = omap_readw(UDC_REV) & 0xff;
2310 seq_printf(s,
2311 "UDC rev %d.%d, fifo mode %d, gadget %s\n"
2312 "hmc %d, transceiver %s\n",
2313 tmp >> 4, tmp & 0xf,
2314 fifo_mode,
2315 udc->driver ? udc->driver->driver.name : "(none)",
2316 HMC,
2317 udc->transceiver
2318 ? udc->transceiver->label
2319 : (cpu_is_omap1710()
2320 ? "external" : "(none)"));
2321 seq_printf(s, "ULPD control %04x req %04x status %04x\n",
2322 omap_readw(ULPD_CLOCK_CTRL),
2323 omap_readw(ULPD_SOFT_REQ),
2324 omap_readw(ULPD_STATUS_REQ));
2325
2326 /* OTG controller registers */
2327 if (!cpu_is_omap15xx())
2328 proc_otg_show(s);
2329
2330 tmp = omap_readw(UDC_SYSCON1);
2331 seq_printf(s, "\nsyscon1 %04x" EIGHTBITS "\n", tmp,
2332 (tmp & UDC_CFG_LOCK) ? " cfg_lock" : "",
2333 (tmp & UDC_DATA_ENDIAN) ? " data_endian" : "",
2334 (tmp & UDC_DMA_ENDIAN) ? " dma_endian" : "",
2335 (tmp & UDC_NAK_EN) ? " nak" : "",
2336 (tmp & UDC_AUTODECODE_DIS) ? " autodecode_dis" : "",
2337 (tmp & UDC_SELF_PWR) ? " self_pwr" : "",
2338 (tmp & UDC_SOFF_DIS) ? " soff_dis" : "",
2339 (tmp & UDC_PULLUP_EN) ? " PULLUP" : "");
2340 /* syscon2 is write-only */
2341
2342 /* UDC controller registers */
2343 if (!(tmp & UDC_PULLUP_EN)) {
2344 seq_printf(s, "(suspended)\n");
2345 spin_unlock_irqrestore(&udc->lock, flags);
2346 return 0;
2347 }
2348
2349 tmp = omap_readw(UDC_DEVSTAT);
2350 seq_printf(s, "devstat %04x" EIGHTBITS "%s%s\n", tmp,
2351 (tmp & UDC_B_HNP_ENABLE) ? " b_hnp" : "",
2352 (tmp & UDC_A_HNP_SUPPORT) ? " a_hnp" : "",
2353 (tmp & UDC_A_ALT_HNP_SUPPORT) ? " a_alt_hnp" : "",
2354 (tmp & UDC_R_WK_OK) ? " r_wk_ok" : "",
2355 (tmp & UDC_USB_RESET) ? " usb_reset" : "",
2356 (tmp & UDC_SUS) ? " SUS" : "",
2357 (tmp & UDC_CFG) ? " CFG" : "",
2358 (tmp & UDC_ADD) ? " ADD" : "",
2359 (tmp & UDC_DEF) ? " DEF" : "",
2360 (tmp & UDC_ATT) ? " ATT" : "");
2361 seq_printf(s, "sof %04x\n", omap_readw(UDC_SOF));
2362 tmp = omap_readw(UDC_IRQ_EN);
2363 seq_printf(s, "irq_en %04x" FOURBITS "%s\n", tmp,
2364 (tmp & UDC_SOF_IE) ? " sof" : "",
2365 (tmp & UDC_EPN_RX_IE) ? " epn_rx" : "",
2366 (tmp & UDC_EPN_TX_IE) ? " epn_tx" : "",
2367 (tmp & UDC_DS_CHG_IE) ? " ds_chg" : "",
2368 (tmp & UDC_EP0_IE) ? " ep0" : "");
2369 tmp = omap_readw(UDC_IRQ_SRC);
2370 seq_printf(s, "irq_src %04x" EIGHTBITS "%s%s\n", tmp,
2371 (tmp & UDC_TXN_DONE) ? " txn_done" : "",
2372 (tmp & UDC_RXN_CNT) ? " rxn_cnt" : "",
2373 (tmp & UDC_RXN_EOT) ? " rxn_eot" : "",
2374 (tmp & UDC_IRQ_SOF) ? " sof" : "",
2375 (tmp & UDC_EPN_RX) ? " epn_rx" : "",
2376 (tmp & UDC_EPN_TX) ? " epn_tx" : "",
2377 (tmp & UDC_DS_CHG) ? " ds_chg" : "",
2378 (tmp & UDC_SETUP) ? " setup" : "",
2379 (tmp & UDC_EP0_RX) ? " ep0out" : "",
2380 (tmp & UDC_EP0_TX) ? " ep0in" : "");
2381 if (use_dma) {
2382 unsigned i;
2383
2384 tmp = omap_readw(UDC_DMA_IRQ_EN);
2385 seq_printf(s, "dma_irq_en %04x%s" EIGHTBITS "\n", tmp,
2386 (tmp & UDC_TX_DONE_IE(3)) ? " tx2_done" : "",
2387 (tmp & UDC_RX_CNT_IE(3)) ? " rx2_cnt" : "",
2388 (tmp & UDC_RX_EOT_IE(3)) ? " rx2_eot" : "",
2389
2390 (tmp & UDC_TX_DONE_IE(2)) ? " tx1_done" : "",
2391 (tmp & UDC_RX_CNT_IE(2)) ? " rx1_cnt" : "",
2392 (tmp & UDC_RX_EOT_IE(2)) ? " rx1_eot" : "",
2393
2394 (tmp & UDC_TX_DONE_IE(1)) ? " tx0_done" : "",
2395 (tmp & UDC_RX_CNT_IE(1)) ? " rx0_cnt" : "",
2396 (tmp & UDC_RX_EOT_IE(1)) ? " rx0_eot" : "");
2397
2398 tmp = omap_readw(UDC_RXDMA_CFG);
2399 seq_printf(s, "rxdma_cfg %04x\n", tmp);
2400 if (tmp) {
2401 for (i = 0; i < 3; i++) {
2402 if ((tmp & (0x0f << (i * 4))) == 0)
2403 continue;
2404 seq_printf(s, "rxdma[%d] %04x\n", i,
2405 omap_readw(UDC_RXDMA(i + 1)));
2406 }
2407 }
2408 tmp = omap_readw(UDC_TXDMA_CFG);
2409 seq_printf(s, "txdma_cfg %04x\n", tmp);
2410 if (tmp) {
2411 for (i = 0; i < 3; i++) {
2412 if (!(tmp & (0x0f << (i * 4))))
2413 continue;
2414 seq_printf(s, "txdma[%d] %04x\n", i,
2415 omap_readw(UDC_TXDMA(i + 1)));
2416 }
2417 }
2418 }
2419
2420 tmp = omap_readw(UDC_DEVSTAT);
2421 if (tmp & UDC_ATT) {
2422 proc_ep_show(s, &udc->ep[0]);
2423 if (tmp & UDC_ADD) {
2424 list_for_each_entry(ep, &udc->gadget.ep_list,
2425 ep.ep_list) {
2426 if (ep->ep.desc)
2427 proc_ep_show(s, ep);
2428 }
2429 }
2430 }
2431 spin_unlock_irqrestore(&udc->lock, flags);
2432 return 0;
2433 }
2434
2435 static void create_proc_file(void)
2436 {
2437 proc_create_single(proc_filename, 0, NULL, proc_udc_show);
2438 }
2439
2440 static void remove_proc_file(void)
2441 {
2442 remove_proc_entry(proc_filename, NULL);
2443 }
2444
2445 #else
2446
2447 static inline void create_proc_file(void) {}
2448 static inline void remove_proc_file(void) {}
2449
2450 #endif
2451
2452 /*-------------------------------------------------------------------------*/
2453
2454 /* Before this controller can enumerate, we need to pick an endpoint
2455 * configuration, or "fifo_mode" That involves allocating 2KB of packet
2456 * buffer space among the endpoints we'll be operating.
2457 *
2458 * NOTE: as of OMAP 1710 ES2.0, writing a new endpoint config when
2459 * UDC_SYSCON_1.CFG_LOCK is set can now work. We won't use that
2460 * capability yet though.
2461 */
2462 static unsigned
2463 omap_ep_setup(char *name, u8 addr, u8 type,
2464 unsigned buf, unsigned maxp, int dbuf)
2465 {
2466 struct omap_ep *ep;
2467 u16 epn_rxtx = 0;
2468
2469 /* OUT endpoints first, then IN */
2470 ep = &udc->ep[addr & 0xf];
2471 if (addr & USB_DIR_IN)
2472 ep += 16;
2473
2474 /* in case of ep init table bugs */
2475 BUG_ON(ep->name[0]);
2476
2477 /* chip setup ... bit values are same for IN, OUT */
2478 if (type == USB_ENDPOINT_XFER_ISOC) {
2479 switch (maxp) {
2480 case 8:
2481 epn_rxtx = 0 << 12;
2482 break;
2483 case 16:
2484 epn_rxtx = 1 << 12;
2485 break;
2486 case 32:
2487 epn_rxtx = 2 << 12;
2488 break;
2489 case 64:
2490 epn_rxtx = 3 << 12;
2491 break;
2492 case 128:
2493 epn_rxtx = 4 << 12;
2494 break;
2495 case 256:
2496 epn_rxtx = 5 << 12;
2497 break;
2498 case 512:
2499 epn_rxtx = 6 << 12;
2500 break;
2501 default:
2502 BUG();
2503 }
2504 epn_rxtx |= UDC_EPN_RX_ISO;
2505 dbuf = 1;
2506 } else {
2507 /* double-buffering "not supported" on 15xx,
2508 * and ignored for PIO-IN on newer chips
2509 * (for more reliable behavior)
2510 */
2511 if (!use_dma || cpu_is_omap15xx())
2512 dbuf = 0;
2513
2514 switch (maxp) {
2515 case 8:
2516 epn_rxtx = 0 << 12;
2517 break;
2518 case 16:
2519 epn_rxtx = 1 << 12;
2520 break;
2521 case 32:
2522 epn_rxtx = 2 << 12;
2523 break;
2524 case 64:
2525 epn_rxtx = 3 << 12;
2526 break;
2527 default:
2528 BUG();
2529 }
2530 if (dbuf && addr)
2531 epn_rxtx |= UDC_EPN_RX_DB;
2532 timer_setup(&ep->timer, pio_out_timer, 0);
2533 }
2534 if (addr)
2535 epn_rxtx |= UDC_EPN_RX_VALID;
2536 BUG_ON(buf & 0x07);
2537 epn_rxtx |= buf >> 3;
2538
2539 DBG("%s addr %02x rxtx %04x maxp %d%s buf %d\n",
2540 name, addr, epn_rxtx, maxp, dbuf ? "x2" : "", buf);
2541
2542 if (addr & USB_DIR_IN)
2543 omap_writew(epn_rxtx, UDC_EP_TX(addr & 0xf));
2544 else
2545 omap_writew(epn_rxtx, UDC_EP_RX(addr));
2546
2547 /* next endpoint's buffer starts after this one's */
2548 buf += maxp;
2549 if (dbuf)
2550 buf += maxp;
2551 BUG_ON(buf > 2048);
2552
2553 /* set up driver data structures */
2554 BUG_ON(strlen(name) >= sizeof ep->name);
2555 strlcpy(ep->name, name, sizeof ep->name);
2556 INIT_LIST_HEAD(&ep->queue);
2557 INIT_LIST_HEAD(&ep->iso);
2558 ep->bEndpointAddress = addr;
2559 ep->bmAttributes = type;
2560 ep->double_buf = dbuf;
2561 ep->udc = udc;
2562
2563 switch (type) {
2564 case USB_ENDPOINT_XFER_CONTROL:
2565 ep->ep.caps.type_control = true;
2566 ep->ep.caps.dir_in = true;
2567 ep->ep.caps.dir_out = true;
2568 break;
2569 case USB_ENDPOINT_XFER_ISOC:
2570 ep->ep.caps.type_iso = true;
2571 break;
2572 case USB_ENDPOINT_XFER_BULK:
2573 ep->ep.caps.type_bulk = true;
2574 break;
2575 case USB_ENDPOINT_XFER_INT:
2576 ep->ep.caps.type_int = true;
2577 break;
2578 };
2579
2580 if (addr & USB_DIR_IN)
2581 ep->ep.caps.dir_in = true;
2582 else
2583 ep->ep.caps.dir_out = true;
2584
2585 ep->ep.name = ep->name;
2586 ep->ep.ops = &omap_ep_ops;
2587 ep->maxpacket = maxp;
2588 usb_ep_set_maxpacket_limit(&ep->ep, ep->maxpacket);
2589 list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
2590
2591 return buf;
2592 }
2593
2594 static void omap_udc_release(struct device *dev)
2595 {
2596 complete(udc->done);
2597 kfree(udc);
2598 udc = NULL;
2599 }
2600
2601 static int
2602 omap_udc_setup(struct platform_device *odev, struct usb_phy *xceiv)
2603 {
2604 unsigned tmp, buf;
2605
2606 /* abolish any previous hardware state */
2607 omap_writew(0, UDC_SYSCON1);
2608 omap_writew(0, UDC_IRQ_EN);
2609 omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC);
2610 omap_writew(0, UDC_DMA_IRQ_EN);
2611 omap_writew(0, UDC_RXDMA_CFG);
2612 omap_writew(0, UDC_TXDMA_CFG);
2613
2614 /* UDC_PULLUP_EN gates the chip clock */
2615 /* OTG_SYSCON_1 |= DEV_IDLE_EN; */
2616
2617 udc = kzalloc(sizeof(*udc), GFP_KERNEL);
2618 if (!udc)
2619 return -ENOMEM;
2620
2621 spin_lock_init(&udc->lock);
2622
2623 udc->gadget.ops = &omap_gadget_ops;
2624 udc->gadget.ep0 = &udc->ep[0].ep;
2625 INIT_LIST_HEAD(&udc->gadget.ep_list);
2626 INIT_LIST_HEAD(&udc->iso);
2627 udc->gadget.speed = USB_SPEED_UNKNOWN;
2628 udc->gadget.max_speed = USB_SPEED_FULL;
2629 udc->gadget.name = driver_name;
2630 udc->transceiver = xceiv;
2631
2632 /* ep0 is special; put it right after the SETUP buffer */
2633 buf = omap_ep_setup("ep0", 0, USB_ENDPOINT_XFER_CONTROL,
2634 8 /* after SETUP */, 64 /* maxpacket */, 0);
2635 list_del_init(&udc->ep[0].ep.ep_list);
2636
2637 /* initially disable all non-ep0 endpoints */
2638 for (tmp = 1; tmp < 15; tmp++) {
2639 omap_writew(0, UDC_EP_RX(tmp));
2640 omap_writew(0, UDC_EP_TX(tmp));
2641 }
2642
2643 #define OMAP_BULK_EP(name, addr) \
2644 buf = omap_ep_setup(name "-bulk", addr, \
2645 USB_ENDPOINT_XFER_BULK, buf, 64, 1);
2646 #define OMAP_INT_EP(name, addr, maxp) \
2647 buf = omap_ep_setup(name "-int", addr, \
2648 USB_ENDPOINT_XFER_INT, buf, maxp, 0);
2649 #define OMAP_ISO_EP(name, addr, maxp) \
2650 buf = omap_ep_setup(name "-iso", addr, \
2651 USB_ENDPOINT_XFER_ISOC, buf, maxp, 1);
2652
2653 switch (fifo_mode) {
2654 case 0:
2655 OMAP_BULK_EP("ep1in", USB_DIR_IN | 1);
2656 OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2);
2657 OMAP_INT_EP("ep3in", USB_DIR_IN | 3, 16);
2658 break;
2659 case 1:
2660 OMAP_BULK_EP("ep1in", USB_DIR_IN | 1);
2661 OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2);
2662 OMAP_INT_EP("ep9in", USB_DIR_IN | 9, 16);
2663
2664 OMAP_BULK_EP("ep3in", USB_DIR_IN | 3);
2665 OMAP_BULK_EP("ep4out", USB_DIR_OUT | 4);
2666 OMAP_INT_EP("ep10in", USB_DIR_IN | 10, 16);
2667
2668 OMAP_BULK_EP("ep5in", USB_DIR_IN | 5);
2669 OMAP_BULK_EP("ep5out", USB_DIR_OUT | 5);
2670 OMAP_INT_EP("ep11in", USB_DIR_IN | 11, 16);
2671
2672 OMAP_BULK_EP("ep6in", USB_DIR_IN | 6);
2673 OMAP_BULK_EP("ep6out", USB_DIR_OUT | 6);
2674 OMAP_INT_EP("ep12in", USB_DIR_IN | 12, 16);
2675
2676 OMAP_BULK_EP("ep7in", USB_DIR_IN | 7);
2677 OMAP_BULK_EP("ep7out", USB_DIR_OUT | 7);
2678 OMAP_INT_EP("ep13in", USB_DIR_IN | 13, 16);
2679 OMAP_INT_EP("ep13out", USB_DIR_OUT | 13, 16);
2680
2681 OMAP_BULK_EP("ep8in", USB_DIR_IN | 8);
2682 OMAP_BULK_EP("ep8out", USB_DIR_OUT | 8);
2683 OMAP_INT_EP("ep14in", USB_DIR_IN | 14, 16);
2684 OMAP_INT_EP("ep14out", USB_DIR_OUT | 14, 16);
2685
2686 OMAP_BULK_EP("ep15in", USB_DIR_IN | 15);
2687 OMAP_BULK_EP("ep15out", USB_DIR_OUT | 15);
2688
2689 break;
2690
2691 #ifdef USE_ISO
2692 case 2: /* mixed iso/bulk */
2693 OMAP_ISO_EP("ep1in", USB_DIR_IN | 1, 256);
2694 OMAP_ISO_EP("ep2out", USB_DIR_OUT | 2, 256);
2695 OMAP_ISO_EP("ep3in", USB_DIR_IN | 3, 128);
2696 OMAP_ISO_EP("ep4out", USB_DIR_OUT | 4, 128);
2697
2698 OMAP_INT_EP("ep5in", USB_DIR_IN | 5, 16);
2699
2700 OMAP_BULK_EP("ep6in", USB_DIR_IN | 6);
2701 OMAP_BULK_EP("ep7out", USB_DIR_OUT | 7);
2702 OMAP_INT_EP("ep8in", USB_DIR_IN | 8, 16);
2703 break;
2704 case 3: /* mixed bulk/iso */
2705 OMAP_BULK_EP("ep1in", USB_DIR_IN | 1);
2706 OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2);
2707 OMAP_INT_EP("ep3in", USB_DIR_IN | 3, 16);
2708
2709 OMAP_BULK_EP("ep4in", USB_DIR_IN | 4);
2710 OMAP_BULK_EP("ep5out", USB_DIR_OUT | 5);
2711 OMAP_INT_EP("ep6in", USB_DIR_IN | 6, 16);
2712
2713 OMAP_ISO_EP("ep7in", USB_DIR_IN | 7, 256);
2714 OMAP_ISO_EP("ep8out", USB_DIR_OUT | 8, 256);
2715 OMAP_INT_EP("ep9in", USB_DIR_IN | 9, 16);
2716 break;
2717 #endif
2718
2719 /* add more modes as needed */
2720
2721 default:
2722 ERR("unsupported fifo_mode #%d\n", fifo_mode);
2723 return -ENODEV;
2724 }
2725 omap_writew(UDC_CFG_LOCK|UDC_SELF_PWR, UDC_SYSCON1);
2726 INFO("fifo mode %d, %d bytes not used\n", fifo_mode, 2048 - buf);
2727 return 0;
2728 }
2729
2730 static int omap_udc_probe(struct platform_device *pdev)
2731 {
2732 int status = -ENODEV;
2733 int hmc;
2734 struct usb_phy *xceiv = NULL;
2735 const char *type = NULL;
2736 struct omap_usb_config *config = dev_get_platdata(&pdev->dev);
2737 struct clk *dc_clk = NULL;
2738 struct clk *hhc_clk = NULL;
2739
2740 if (cpu_is_omap7xx())
2741 use_dma = 0;
2742
2743 /* NOTE: "knows" the order of the resources! */
2744 if (!request_mem_region(pdev->resource[0].start,
2745 pdev->resource[0].end - pdev->resource[0].start + 1,
2746 driver_name)) {
2747 DBG("request_mem_region failed\n");
2748 return -EBUSY;
2749 }
2750
2751 if (cpu_is_omap16xx()) {
2752 dc_clk = clk_get(&pdev->dev, "usb_dc_ck");
2753 hhc_clk = clk_get(&pdev->dev, "usb_hhc_ck");
2754 BUG_ON(IS_ERR(dc_clk) || IS_ERR(hhc_clk));
2755 /* can't use omap_udc_enable_clock yet */
2756 clk_enable(dc_clk);
2757 clk_enable(hhc_clk);
2758 udelay(100);
2759 }
2760
2761 if (cpu_is_omap7xx()) {
2762 dc_clk = clk_get(&pdev->dev, "usb_dc_ck");
2763 hhc_clk = clk_get(&pdev->dev, "l3_ocpi_ck");
2764 BUG_ON(IS_ERR(dc_clk) || IS_ERR(hhc_clk));
2765 /* can't use omap_udc_enable_clock yet */
2766 clk_enable(dc_clk);
2767 clk_enable(hhc_clk);
2768 udelay(100);
2769 }
2770
2771 INFO("OMAP UDC rev %d.%d%s\n",
2772 omap_readw(UDC_REV) >> 4, omap_readw(UDC_REV) & 0xf,
2773 config->otg ? ", Mini-AB" : "");
2774
2775 /* use the mode given to us by board init code */
2776 if (cpu_is_omap15xx()) {
2777 hmc = HMC_1510;
2778 type = "(unknown)";
2779
2780 if (machine_without_vbus_sense()) {
2781 /* just set up software VBUS detect, and then
2782 * later rig it so we always report VBUS.
2783 * FIXME without really sensing VBUS, we can't
2784 * know when to turn PULLUP_EN on/off; and that
2785 * means we always "need" the 48MHz clock.
2786 */
2787 u32 tmp = omap_readl(FUNC_MUX_CTRL_0);
2788 tmp &= ~VBUS_CTRL_1510;
2789 omap_writel(tmp, FUNC_MUX_CTRL_0);
2790 tmp |= VBUS_MODE_1510;
2791 tmp &= ~VBUS_CTRL_1510;
2792 omap_writel(tmp, FUNC_MUX_CTRL_0);
2793 }
2794 } else {
2795 /* The transceiver may package some GPIO logic or handle
2796 * loopback and/or transceiverless setup; if we find one,
2797 * use it. Except for OTG, we don't _need_ to talk to one;
2798 * but not having one probably means no VBUS detection.
2799 */
2800 xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
2801 if (!IS_ERR_OR_NULL(xceiv))
2802 type = xceiv->label;
2803 else if (config->otg) {
2804 DBG("OTG requires external transceiver!\n");
2805 goto cleanup0;
2806 }
2807
2808 hmc = HMC_1610;
2809
2810 switch (hmc) {
2811 case 0: /* POWERUP DEFAULT == 0 */
2812 case 4:
2813 case 12:
2814 case 20:
2815 if (!cpu_is_omap1710()) {
2816 type = "integrated";
2817 break;
2818 }
2819 /* FALL THROUGH */
2820 case 3:
2821 case 11:
2822 case 16:
2823 case 19:
2824 case 25:
2825 if (IS_ERR_OR_NULL(xceiv)) {
2826 DBG("external transceiver not registered!\n");
2827 type = "unknown";
2828 }
2829 break;
2830 case 21: /* internal loopback */
2831 type = "loopback";
2832 break;
2833 case 14: /* transceiverless */
2834 if (cpu_is_omap1710())
2835 goto bad_on_1710;
2836 /* FALL THROUGH */
2837 case 13:
2838 case 15:
2839 type = "no";
2840 break;
2841
2842 default:
2843 bad_on_1710:
2844 ERR("unrecognized UDC HMC mode %d\n", hmc);
2845 goto cleanup0;
2846 }
2847 }
2848
2849 INFO("hmc mode %d, %s transceiver\n", hmc, type);
2850
2851 /* a "gadget" abstracts/virtualizes the controller */
2852 status = omap_udc_setup(pdev, xceiv);
2853 if (status)
2854 goto cleanup0;
2855
2856 xceiv = NULL;
2857 /* "udc" is now valid */
2858 pullup_disable(udc);
2859 #if IS_ENABLED(CONFIG_USB_OHCI_HCD)
2860 udc->gadget.is_otg = (config->otg != 0);
2861 #endif
2862
2863 /* starting with omap1710 es2.0, clear toggle is a separate bit */
2864 if (omap_readw(UDC_REV) >= 0x61)
2865 udc->clr_halt = UDC_RESET_EP | UDC_CLRDATA_TOGGLE;
2866 else
2867 udc->clr_halt = UDC_RESET_EP;
2868
2869 /* USB general purpose IRQ: ep0, state changes, dma, etc */
2870 status = request_irq(pdev->resource[1].start, omap_udc_irq,
2871 0, driver_name, udc);
2872 if (status != 0) {
2873 ERR("can't get irq %d, err %d\n",
2874 (int) pdev->resource[1].start, status);
2875 goto cleanup1;
2876 }
2877
2878 /* USB "non-iso" IRQ (PIO for all but ep0) */
2879 status = request_irq(pdev->resource[2].start, omap_udc_pio_irq,
2880 0, "omap_udc pio", udc);
2881 if (status != 0) {
2882 ERR("can't get irq %d, err %d\n",
2883 (int) pdev->resource[2].start, status);
2884 goto cleanup2;
2885 }
2886 #ifdef USE_ISO
2887 status = request_irq(pdev->resource[3].start, omap_udc_iso_irq,
2888 0, "omap_udc iso", udc);
2889 if (status != 0) {
2890 ERR("can't get irq %d, err %d\n",
2891 (int) pdev->resource[3].start, status);
2892 goto cleanup3;
2893 }
2894 #endif
2895 if (cpu_is_omap16xx() || cpu_is_omap7xx()) {
2896 udc->dc_clk = dc_clk;
2897 udc->hhc_clk = hhc_clk;
2898 clk_disable(hhc_clk);
2899 clk_disable(dc_clk);
2900 }
2901
2902 create_proc_file();
2903 status = usb_add_gadget_udc_release(&pdev->dev, &udc->gadget,
2904 omap_udc_release);
2905 if (status)
2906 goto cleanup4;
2907
2908 return 0;
2909
2910 cleanup4:
2911 remove_proc_file();
2912
2913 #ifdef USE_ISO
2914 cleanup3:
2915 free_irq(pdev->resource[2].start, udc);
2916 #endif
2917
2918 cleanup2:
2919 free_irq(pdev->resource[1].start, udc);
2920
2921 cleanup1:
2922 kfree(udc);
2923 udc = NULL;
2924
2925 cleanup0:
2926 if (!IS_ERR_OR_NULL(xceiv))
2927 usb_put_phy(xceiv);
2928
2929 if (cpu_is_omap16xx() || cpu_is_omap7xx()) {
2930 clk_disable(hhc_clk);
2931 clk_disable(dc_clk);
2932 clk_put(hhc_clk);
2933 clk_put(dc_clk);
2934 }
2935
2936 release_mem_region(pdev->resource[0].start,
2937 pdev->resource[0].end - pdev->resource[0].start + 1);
2938
2939 return status;
2940 }
2941
2942 static int omap_udc_remove(struct platform_device *pdev)
2943 {
2944 DECLARE_COMPLETION_ONSTACK(done);
2945
2946 if (!udc)
2947 return -ENODEV;
2948
2949 usb_del_gadget_udc(&udc->gadget);
2950 if (udc->driver)
2951 return -EBUSY;
2952
2953 udc->done = &done;
2954
2955 pullup_disable(udc);
2956 if (!IS_ERR_OR_NULL(udc->transceiver)) {
2957 usb_put_phy(udc->transceiver);
2958 udc->transceiver = NULL;
2959 }
2960 omap_writew(0, UDC_SYSCON1);
2961
2962 remove_proc_file();
2963
2964 #ifdef USE_ISO
2965 free_irq(pdev->resource[3].start, udc);
2966 #endif
2967 free_irq(pdev->resource[2].start, udc);
2968 free_irq(pdev->resource[1].start, udc);
2969
2970 if (udc->dc_clk) {
2971 if (udc->clk_requested)
2972 omap_udc_enable_clock(0);
2973 clk_put(udc->hhc_clk);
2974 clk_put(udc->dc_clk);
2975 }
2976
2977 release_mem_region(pdev->resource[0].start,
2978 pdev->resource[0].end - pdev->resource[0].start + 1);
2979
2980 wait_for_completion(&done);
2981
2982 return 0;
2983 }
2984
2985 /* suspend/resume/wakeup from sysfs (echo > power/state) or when the
2986 * system is forced into deep sleep
2987 *
2988 * REVISIT we should probably reject suspend requests when there's a host
2989 * session active, rather than disconnecting, at least on boards that can
2990 * report VBUS irqs (UDC_DEVSTAT.UDC_ATT). And in any case, we need to
2991 * make host resumes and VBUS detection trigger OMAP wakeup events; that
2992 * may involve talking to an external transceiver (e.g. isp1301).
2993 */
2994
2995 static int omap_udc_suspend(struct platform_device *dev, pm_message_t message)
2996 {
2997 u32 devstat;
2998
2999 devstat = omap_readw(UDC_DEVSTAT);
3000
3001 /* we're requesting 48 MHz clock if the pullup is enabled
3002 * (== we're attached to the host) and we're not suspended,
3003 * which would prevent entry to deep sleep...
3004 */
3005 if ((devstat & UDC_ATT) != 0 && (devstat & UDC_SUS) == 0) {
3006 WARNING("session active; suspend requires disconnect\n");
3007 omap_pullup(&udc->gadget, 0);
3008 }
3009
3010 return 0;
3011 }
3012
3013 static int omap_udc_resume(struct platform_device *dev)
3014 {
3015 DBG("resume + wakeup/SRP\n");
3016 omap_pullup(&udc->gadget, 1);
3017
3018 /* maybe the host would enumerate us if we nudged it */
3019 msleep(100);
3020 return omap_wakeup(&udc->gadget);
3021 }
3022
3023 /*-------------------------------------------------------------------------*/
3024
3025 static struct platform_driver udc_driver = {
3026 .probe = omap_udc_probe,
3027 .remove = omap_udc_remove,
3028 .suspend = omap_udc_suspend,
3029 .resume = omap_udc_resume,
3030 .driver = {
3031 .name = (char *) driver_name,
3032 },
3033 };
3034
3035 module_platform_driver(udc_driver);
3036
3037 MODULE_DESCRIPTION(DRIVER_DESC);
3038 MODULE_LICENSE("GPL");
3039 MODULE_ALIAS("platform:omap_udc");
Ubuntu Jammy Linux kernel mirror