drivers/usb/host/ohci-at91.c

   1 /*
   2  * OHCI HCD (Host Controller Driver) for USB.
   3  *
   4  *  Copyright (C) 2004 SAN People (Pty) Ltd.
   5  *  Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
   6  *
   7  * AT91 Bus Glue
   8  *
   9  * Based on fragments of 2.4 driver by Rick Bronson.
  10  * Based on ohci-omap.c
  11  *
  12  * This file is licenced under the GPL.
  13  */
  14
  15 #include <linux/clk.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/of_platform.h>
  18 #include <linux/of_gpio.h>
  19
  20 #include <mach/hardware.h>
  21 #include <asm/gpio.h>
  22
  23 #include <mach/board.h>
  24 #include <mach/cpu.h>
  25
  26 #ifndef CONFIG_ARCH_AT91
  27 #error "CONFIG_ARCH_AT91 must be defined."
  28 #endif
  29
  30 #define valid_port(index)       ((index) >= 0 && (index) < AT91_MAX_USBH_PORTS)
  31 #define at91_for_each_port(index)       \
  32                 for ((index) = 0; (index) < AT91_MAX_USBH_PORTS; (index)++)
  33
  34 /* interface and function clocks; sometimes also an AHB clock */
  35 static struct clk *iclk, *fclk, *hclk;
  36 static int clocked;
  37
  38 extern int usb_disabled(void);
  39
  40 /*-------------------------------------------------------------------------*/
  41
  42 static void at91_start_clock(void)
  43 {
  44         clk_enable(hclk);
  45         clk_enable(iclk);
  46         clk_enable(fclk);
  47         clocked = 1;
  48 }
  49
  50 static void at91_stop_clock(void)
  51 {
  52         clk_disable(fclk);
  53         clk_disable(iclk);
  54         clk_disable(hclk);
  55         clocked = 0;
  56 }
  57
  58 static void at91_start_hc(struct platform_device *pdev)
  59 {
  60         struct usb_hcd *hcd = platform_get_drvdata(pdev);
  61         struct ohci_regs __iomem *regs = hcd->regs;
  62
  63         dev_dbg(&pdev->dev, "start\n");
  64
  65         /*
  66          * Start the USB clocks.
  67          */
  68         at91_start_clock();
  69
  70         /*
  71          * The USB host controller must remain in reset.
  72          */
  73         writel(0, &regs->control);
  74 }
  75
  76 static void at91_stop_hc(struct platform_device *pdev)
  77 {
  78         struct usb_hcd *hcd = platform_get_drvdata(pdev);
  79         struct ohci_regs __iomem *regs = hcd->regs;
  80
  81         dev_dbg(&pdev->dev, "stop\n");
  82
  83         /*
  84          * Put the USB host controller into reset.
  85          */
  86         writel(0, &regs->control);
  87
  88         /*
  89          * Stop the USB clocks.
  90          */
  91         at91_stop_clock();
  92 }
  93
  94
  95 /*-------------------------------------------------------------------------*/
  96
  97 static void __devexit usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *);
  98
  99 /* configure so an HC device and id are always provided */
 100 /* always called with process context; sleeping is OK */
 101
 102
 103 /**
 104  * usb_hcd_at91_probe - initialize AT91-based HCDs
 105  * Context: !in_interrupt()
 106  *
 107  * Allocates basic resources for this USB host controller, and
 108  * then invokes the start() method for the HCD associated with it
 109  * through the hotplug entry's driver_data.
 110  */
 111 static int __devinit usb_hcd_at91_probe(const struct hc_driver *driver,
 112                         struct platform_device *pdev)
 113 {
 114         int retval;
 115         struct usb_hcd *hcd = NULL;
 116
 117         if (pdev->num_resources != 2) {
 118                 pr_debug("hcd probe: invalid num_resources");
 119                 return -ENODEV;
 120         }
 121
 122         if ((pdev->resource[0].flags != IORESOURCE_MEM)
 123                         || (pdev->resource[1].flags != IORESOURCE_IRQ)) {
 124                 pr_debug("hcd probe: invalid resource type\n");
 125                 return -ENODEV;
 126         }
 127
 128         hcd = usb_create_hcd(driver, &pdev->dev, "at91");
 129         if (!hcd)
 130                 return -ENOMEM;
 131         hcd->rsrc_start = pdev->resource[0].start;
 132         hcd->rsrc_len = resource_size(&pdev->resource[0]);
 133
 134         if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
 135                 pr_debug("request_mem_region failed\n");
 136                 retval = -EBUSY;
 137                 goto err1;
 138         }
 139
 140         hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
 141         if (!hcd->regs) {
 142                 pr_debug("ioremap failed\n");
 143                 retval = -EIO;
 144                 goto err2;
 145         }
 146
 147         iclk = clk_get(&pdev->dev, "ohci_clk");
 148         if (IS_ERR(iclk)) {
 149                 dev_err(&pdev->dev, "failed to get ohci_clk\n");
 150                 retval = PTR_ERR(iclk);
 151                 goto err3;
 152         }
 153         fclk = clk_get(&pdev->dev, "uhpck");
 154         if (IS_ERR(fclk)) {
 155                 dev_err(&pdev->dev, "failed to get uhpck\n");
 156                 retval = PTR_ERR(fclk);
 157                 goto err4;
 158         }
 159         hclk = clk_get(&pdev->dev, "hclk");
 160         if (IS_ERR(hclk)) {
 161                 dev_err(&pdev->dev, "failed to get hclk\n");
 162                 retval = PTR_ERR(hclk);
 163                 goto err5;
 164         }
 165
 166         at91_start_hc(pdev);
 167         ohci_hcd_init(hcd_to_ohci(hcd));
 168
 169         retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_SHARED);
 170         if (retval == 0)
 171                 return retval;
 172
 173         /* Error handling */
 174         at91_stop_hc(pdev);
 175
 176         clk_put(hclk);
 177  err5:
 178         clk_put(fclk);
 179  err4:
 180         clk_put(iclk);
 181
 182  err3:
 183         iounmap(hcd->regs);
 184
 185  err2:
 186         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 187
 188  err1:
 189         usb_put_hcd(hcd);
 190         return retval;
 191 }
 192
 193
 194 /* may be called with controller, bus, and devices active */
 195
 196 /**
 197  * usb_hcd_at91_remove - shutdown processing for AT91-based HCDs
 198  * @dev: USB Host Controller being removed
 199  * Context: !in_interrupt()
 200  *
 201  * Reverses the effect of usb_hcd_at91_probe(), first invoking
 202  * the HCD's stop() method.  It is always called from a thread
 203  * context, "rmmod" or something similar.
 204  *
 205  */
 206 static void __devexit usb_hcd_at91_remove(struct usb_hcd *hcd,
 207                                 struct platform_device *pdev)
 208 {
 209         usb_remove_hcd(hcd);
 210         at91_stop_hc(pdev);
 211         iounmap(hcd->regs);
 212         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 213         usb_put_hcd(hcd);
 214
 215         clk_put(hclk);
 216         clk_put(fclk);
 217         clk_put(iclk);
 218         fclk = iclk = hclk = NULL;
 219
 220         dev_set_drvdata(&pdev->dev, NULL);
 221 }
 222
 223 /*-------------------------------------------------------------------------*/
 224
 225 static int __devinit
 226 ohci_at91_reset (struct usb_hcd *hcd)
 227 {
 228         struct at91_usbh_data   *board = hcd->self.controller->platform_data;
 229         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 230         int                     ret;
 231
 232         if ((ret = ohci_init(ohci)) < 0)
 233                 return ret;
 234
 235         ohci->num_ports = board->ports;
 236         return 0;
 237 }
 238
 239 static int __devinit
 240 ohci_at91_start (struct usb_hcd *hcd)
 241 {
 242         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 243         int                     ret;
 244
 245         if ((ret = ohci_run(ohci)) < 0) {
 246                 dev_err(hcd->self.controller, "can't start %s\n",
 247                         hcd->self.bus_name);
 248                 ohci_stop(hcd);
 249                 return ret;
 250         }
 251         return 0;
 252 }
 253
 254 static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable)
 255 {
 256         if (!valid_port(port))
 257                 return;
 258
 259         if (!gpio_is_valid(pdata->vbus_pin[port]))
 260                 return;
 261
 262         gpio_set_value(pdata->vbus_pin[port],
 263                        pdata->vbus_pin_active_low[port] ^ enable);
 264 }
 265
 266 static int ohci_at91_usb_get_power(struct at91_usbh_data *pdata, int port)
 267 {
 268         if (!valid_port(port))
 269                 return -EINVAL;
 270
 271         if (!gpio_is_valid(pdata->vbus_pin[port]))
 272                 return -EINVAL;
 273
 274         return gpio_get_value(pdata->vbus_pin[port]) ^
 275                 pdata->vbus_pin_active_low[port];
 276 }
 277
 278 /*
 279  * Update the status data from the hub with the over-current indicator change.
 280  */
 281 static int ohci_at91_hub_status_data(struct usb_hcd *hcd, char *buf)
 282 {
 283         struct at91_usbh_data *pdata = hcd->self.controller->platform_data;
 284         int length = ohci_hub_status_data(hcd, buf);
 285         int port;
 286
 287         at91_for_each_port(port) {
 288                 if (pdata->overcurrent_changed[port]) {
 289                         if (!length)
 290                                 length = 1;
 291                         buf[0] |= 1 << (port + 1);
 292                 }
 293         }
 294
 295         return length;
 296 }
 297
 298 /*
 299  * Look at the control requests to the root hub and see if we need to override.
 300  */
 301 static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 302                                  u16 wIndex, char *buf, u16 wLength)
 303 {
 304         struct at91_usbh_data *pdata = hcd->self.controller->platform_data;
 305         struct usb_hub_descriptor *desc;
 306         int ret = -EINVAL;
 307         u32 *data = (u32 *)buf;
 308
 309         dev_dbg(hcd->self.controller,
 310                 "ohci_at91_hub_control(%p,0x%04x,0x%04x,0x%04x,%p,%04x)\n",
 311                 hcd, typeReq, wValue, wIndex, buf, wLength);
 312
 313         wIndex--;
 314
 315         switch (typeReq) {
 316         case SetPortFeature:
 317                 if (wValue == USB_PORT_FEAT_POWER) {
 318                         dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n");
 319                         if (valid_port(wIndex)) {
 320                                 ohci_at91_usb_set_power(pdata, wIndex, 1);
 321                                 ret = 0;
 322                         }
 323
 324                         goto out;
 325                 }
 326                 break;
 327
 328         case ClearPortFeature:
 329                 switch (wValue) {
 330                 case USB_PORT_FEAT_C_OVER_CURRENT:
 331                         dev_dbg(hcd->self.controller,
 332                                 "ClearPortFeature: C_OVER_CURRENT\n");
 333
 334                         if (valid_port(wIndex)) {
 335                                 pdata->overcurrent_changed[wIndex] = 0;
 336                                 pdata->overcurrent_status[wIndex] = 0;
 337                         }
 338
 339                         goto out;
 340
 341                 case USB_PORT_FEAT_OVER_CURRENT:
 342                         dev_dbg(hcd->self.controller,
 343                                 "ClearPortFeature: OVER_CURRENT\n");
 344
 345                         if (valid_port(wIndex))
 346                                 pdata->overcurrent_status[wIndex] = 0;
 347
 348                         goto out;
 349
 350                 case USB_PORT_FEAT_POWER:
 351                         dev_dbg(hcd->self.controller,
 352                                 "ClearPortFeature: POWER\n");
 353
 354                         if (valid_port(wIndex)) {
 355                                 ohci_at91_usb_set_power(pdata, wIndex, 0);
 356                                 return 0;
 357                         }
 358                 }
 359                 break;
 360         }
 361
 362         ret = ohci_hub_control(hcd, typeReq, wValue, wIndex + 1, buf, wLength);
 363         if (ret)
 364                 goto out;
 365
 366         switch (typeReq) {
 367         case GetHubDescriptor:
 368
 369                 /* update the hub's descriptor */
 370
 371                 desc = (struct usb_hub_descriptor *)buf;
 372
 373                 dev_dbg(hcd->self.controller, "wHubCharacteristics 0x%04x\n",
 374                         desc->wHubCharacteristics);
 375
 376                 /* remove the old configurations for power-switching, and
 377                  * over-current protection, and insert our new configuration
 378                  */
 379
 380                 desc->wHubCharacteristics &= ~cpu_to_le16(HUB_CHAR_LPSM);
 381                 desc->wHubCharacteristics |= cpu_to_le16(0x0001);
 382
 383                 if (pdata->overcurrent_supported) {
 384                         desc->wHubCharacteristics &= ~cpu_to_le16(HUB_CHAR_OCPM);
 385                         desc->wHubCharacteristics |=  cpu_to_le16(0x0008|0x0001);
 386                 }
 387
 388                 dev_dbg(hcd->self.controller, "wHubCharacteristics after 0x%04x\n",
 389                         desc->wHubCharacteristics);
 390
 391                 return ret;
 392
 393         case GetPortStatus:
 394                 /* check port status */
 395
 396                 dev_dbg(hcd->self.controller, "GetPortStatus(%d)\n", wIndex);
 397
 398                 if (valid_port(wIndex)) {
 399                         if (!ohci_at91_usb_get_power(pdata, wIndex))
 400                                 *data &= ~cpu_to_le32(RH_PS_PPS);
 401
 402                         if (pdata->overcurrent_changed[wIndex])
 403                                 *data |= cpu_to_le32(RH_PS_OCIC);
 404
 405                         if (pdata->overcurrent_status[wIndex])
 406                                 *data |= cpu_to_le32(RH_PS_POCI);
 407                 }
 408         }
 409
 410  out:
 411         return ret;
 412 }
 413
 414 /*-------------------------------------------------------------------------*/
 415
 416 static const struct hc_driver ohci_at91_hc_driver = {
 417         .description =          hcd_name,
 418         .product_desc =         "AT91 OHCI",
 419         .hcd_priv_size =        sizeof(struct ohci_hcd),
 420
 421         /*
 422          * generic hardware linkage
 423          */
 424         .irq =                  ohci_irq,
 425         .flags =                HCD_USB11 | HCD_MEMORY,
 426
 427         /*
 428          * basic lifecycle operations
 429          */
 430         .reset =                ohci_at91_reset,
 431         .start =                ohci_at91_start,
 432         .stop =                 ohci_stop,
 433         .shutdown =             ohci_shutdown,
 434
 435         /*
 436          * managing i/o requests and associated device resources
 437          */
 438         .urb_enqueue =          ohci_urb_enqueue,
 439         .urb_dequeue =          ohci_urb_dequeue,
 440         .endpoint_disable =     ohci_endpoint_disable,
 441
 442         /*
 443          * scheduling support
 444          */
 445         .get_frame_number =     ohci_get_frame,
 446
 447         /*
 448          * root hub support
 449          */
 450         .hub_status_data =      ohci_at91_hub_status_data,
 451         .hub_control =          ohci_at91_hub_control,
 452 #ifdef CONFIG_PM
 453         .bus_suspend =          ohci_bus_suspend,
 454         .bus_resume =           ohci_bus_resume,
 455 #endif
 456         .start_port_reset =     ohci_start_port_reset,
 457 };
 458
 459 /*-------------------------------------------------------------------------*/
 460
 461 static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data)
 462 {
 463         struct platform_device *pdev = data;
 464         struct at91_usbh_data *pdata = pdev->dev.platform_data;
 465         int val, gpio, port;
 466
 467         /* From the GPIO notifying the over-current situation, find
 468          * out the corresponding port */
 469         at91_for_each_port(port) {
 470                 if (gpio_to_irq(pdata->overcurrent_pin[port]) == irq) {
 471                         gpio = pdata->overcurrent_pin[port];
 472                         break;
 473                 }
 474         }
 475
 476         if (port == AT91_MAX_USBH_PORTS) {
 477                 dev_err(& pdev->dev, "overcurrent interrupt from unknown GPIO\n");
 478                 return IRQ_HANDLED;
 479         }
 480
 481         val = gpio_get_value(gpio);
 482
 483         /* When notified of an over-current situation, disable power
 484            on the corresponding port, and mark this port in
 485            over-current. */
 486         if (!val) {
 487                 ohci_at91_usb_set_power(pdata, port, 0);
 488                 pdata->overcurrent_status[port]  = 1;
 489                 pdata->overcurrent_changed[port] = 1;
 490         }
 491
 492         dev_dbg(& pdev->dev, "overcurrent situation %s\n",
 493                 val ? "exited" : "notified");
 494
 495         return IRQ_HANDLED;
 496 }
 497
 498 #ifdef CONFIG_OF
 499 static const struct of_device_id at91_ohci_dt_ids[] = {
 500         { .compatible = "atmel,at91rm9200-ohci" },
 501         { /* sentinel */ }
 502 };
 503
 504 MODULE_DEVICE_TABLE(of, at91_ohci_dt_ids);
 505
 506 static u64 at91_ohci_dma_mask = DMA_BIT_MASK(32);
 507
 508 static int __devinit ohci_at91_of_init(struct platform_device *pdev)
 509 {
 510         struct device_node *np = pdev->dev.of_node;
 511         int i, gpio;
 512         enum of_gpio_flags flags;
 513         struct at91_usbh_data   *pdata;
 514         u32 ports;
 515
 516         if (!np)
 517                 return 0;
 518
 519         /* Right now device-tree probed devices don't get dma_mask set.
 520          * Since shared usb code relies on it, set it here for now.
 521          * Once we have dma capability bindings this can go away.
 522          */
 523         if (!pdev->dev.dma_mask)
 524                 pdev->dev.dma_mask = &at91_ohci_dma_mask;
 525
 526         pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
 527         if (!pdata)
 528                 return -ENOMEM;
 529
 530         if (!of_property_read_u32(np, "num-ports", &ports))
 531                 pdata->ports = ports;
 532
 533         at91_for_each_port(i) {
 534                 gpio = of_get_named_gpio_flags(np, "atmel,vbus-gpio", i, &flags);
 535                 pdata->vbus_pin[i] = gpio;
 536                 if (!gpio_is_valid(gpio))
 537                         continue;
 538                 pdata->vbus_pin_active_low[i] = flags & OF_GPIO_ACTIVE_LOW;
 539         }
 540
 541         at91_for_each_port(i)
 542                 pdata->overcurrent_pin[i] =
 543                         of_get_named_gpio_flags(np, "atmel,oc-gpio", i, &flags);
 544
 545         pdev->dev.platform_data = pdata;
 546
 547         return 0;
 548 }
 549 #else
 550 static int __devinit ohci_at91_of_init(struct platform_device *pdev)
 551 {
 552         return 0;
 553 }
 554 #endif
 555
 556 /*-------------------------------------------------------------------------*/
 557
 558 static int __devinit ohci_hcd_at91_drv_probe(struct platform_device *pdev)
 559 {
 560         struct at91_usbh_data   *pdata;
 561         int                     i;
 562         int                     gpio;
 563         int                     ret;
 564
 565         ret = ohci_at91_of_init(pdev);
 566         if (ret)
 567                 return ret;
 568
 569         pdata = pdev->dev.platform_data;
 570
 571         if (pdata) {
 572                 at91_for_each_port(i) {
 573                         if (!gpio_is_valid(pdata->vbus_pin[i]))
 574                                 continue;
 575                         gpio = pdata->vbus_pin[i];
 576
 577                         ret = gpio_request(gpio, "ohci_vbus");
 578                         if (ret) {
 579                                 dev_err(&pdev->dev,
 580                                         "can't request vbus gpio %d\n", gpio);
 581                                 continue;
 582                         }
 583                         ret = gpio_direction_output(gpio,
 584                                                 !pdata->vbus_pin_active_low[i]);
 585                         if (ret) {
 586                                 dev_err(&pdev->dev,
 587                                         "can't put vbus gpio %d as output %d\n",
 588                                         gpio, !pdata->vbus_pin_active_low[i]);
 589                                 gpio_free(gpio);
 590                                 continue;
 591                         }
 592
 593                         ohci_at91_usb_set_power(pdata, i, 1);
 594                 }
 595
 596                 at91_for_each_port(i) {
 597                         if (!gpio_is_valid(pdata->overcurrent_pin[i]))
 598                                 continue;
 599                         gpio = pdata->overcurrent_pin[i];
 600
 601                         ret = gpio_request(gpio, "ohci_overcurrent");
 602                         if (ret) {
 603                                 dev_err(&pdev->dev,
 604                                         "can't request overcurrent gpio %d\n",
 605                                         gpio);
 606                                 continue;
 607                         }
 608
 609                         ret = gpio_direction_input(gpio);
 610                         if (ret) {
 611                                 dev_err(&pdev->dev,
 612                                         "can't configure overcurrent gpio %d as input\n",
 613                                         gpio);
 614                                 gpio_free(gpio);
 615                                 continue;
 616                         }
 617
 618                         ret = request_irq(gpio_to_irq(gpio),
 619                                           ohci_hcd_at91_overcurrent_irq,
 620                                           IRQF_SHARED, "ohci_overcurrent", pdev);
 621                         if (ret) {
 622                                 gpio_free(gpio);
 623                                 dev_err(&pdev->dev,
 624                                         "can't get gpio IRQ for overcurrent\n");
 625                         }
 626                 }
 627         }
 628
 629         device_init_wakeup(&pdev->dev, 1);
 630         return usb_hcd_at91_probe(&ohci_at91_hc_driver, pdev);
 631 }
 632
 633 static int __devexit ohci_hcd_at91_drv_remove(struct platform_device *pdev)
 634 {
 635         struct at91_usbh_data   *pdata = pdev->dev.platform_data;
 636         int                     i;
 637
 638         if (pdata) {
 639                 at91_for_each_port(i) {
 640                         if (!gpio_is_valid(pdata->vbus_pin[i]))
 641                                 continue;
 642                         ohci_at91_usb_set_power(pdata, i, 0);
 643                         gpio_free(pdata->vbus_pin[i]);
 644                 }
 645
 646                 at91_for_each_port(i) {
 647                         if (!gpio_is_valid(pdata->overcurrent_pin[i]))
 648                                 continue;
 649                         free_irq(gpio_to_irq(pdata->overcurrent_pin[i]), pdev);
 650                         gpio_free(pdata->overcurrent_pin[i]);
 651                 }
 652         }
 653
 654         device_init_wakeup(&pdev->dev, 0);
 655         usb_hcd_at91_remove(platform_get_drvdata(pdev), pdev);
 656         return 0;
 657 }
 658
 659 #ifdef CONFIG_PM
 660
 661 static int
 662 ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t mesg)
 663 {
 664         struct usb_hcd  *hcd = platform_get_drvdata(pdev);
 665         struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 666
 667         if (device_may_wakeup(&pdev->dev))
 668                 enable_irq_wake(hcd->irq);
 669
 670         /*
 671          * The integrated transceivers seem unable to notice disconnect,
 672          * reconnect, or wakeup without the 48 MHz clock active.  so for
 673          * correctness, always discard connection state (using reset).
 674          *
 675          * REVISIT: some boards will be able to turn VBUS off...
 676          */
 677         if (at91_suspend_entering_slow_clock()) {
 678                 ohci_usb_reset (ohci);
 679                 /* flush the writes */
 680                 (void) ohci_readl (ohci, &ohci->regs->control);
 681                 at91_stop_clock();
 682         }
 683
 684         return 0;
 685 }
 686
 687 static int ohci_hcd_at91_drv_resume(struct platform_device *pdev)
 688 {
 689         struct usb_hcd  *hcd = platform_get_drvdata(pdev);
 690
 691         if (device_may_wakeup(&pdev->dev))
 692                 disable_irq_wake(hcd->irq);
 693
 694         if (!clocked)
 695                 at91_start_clock();
 696
 697         ohci_finish_controller_resume(hcd);
 698         return 0;
 699 }
 700 #else
 701 #define ohci_hcd_at91_drv_suspend NULL
 702 #define ohci_hcd_at91_drv_resume  NULL
 703 #endif
 704
 705 MODULE_ALIAS("platform:at91_ohci");
 706
 707 static struct platform_driver ohci_hcd_at91_driver = {
 708         .probe          = ohci_hcd_at91_drv_probe,
 709         .remove         = __devexit_p(ohci_hcd_at91_drv_remove),
 710         .shutdown       = usb_hcd_platform_shutdown,
 711         .suspend        = ohci_hcd_at91_drv_suspend,
 712         .resume         = ohci_hcd_at91_drv_resume,
 713         .driver         = {
 714                 .name   = "at91_ohci",
 715                 .owner  = THIS_MODULE,
 716                 .of_match_table = of_match_ptr(at91_ohci_dt_ids),
 717         },
 718 };