drivers/usb/phy/Kconfig

   1 #
   2 # Physical Layer USB driver configuration
   3 #
   4 menu "USB Physical Layer drivers"
   5
   6 config USB_PHY
   7         def_bool n
   8
   9 #
  10 # USB Transceiver Drivers
  11 #
  12 config AB8500_USB
  13         tristate "AB8500 USB Transceiver Driver"
  14         depends on AB8500_CORE
  15         select USB_PHY
  16         help
  17           Enable this to support the USB OTG transceiver in AB8500 chip.
  18           This transceiver supports high and full speed devices plus,
  19           in host mode, low speed.
  20
  21 config FSL_USB2_OTG
  22         bool "Freescale USB OTG Transceiver Driver"
  23         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
  24         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  25         select USB_PHY
  26         help
  27           Enable this to support Freescale USB OTG transceiver.
  28
  29 config ISP1301_OMAP
  30         tristate "Philips ISP1301 with OMAP OTG"
  31         depends on I2C && ARCH_OMAP_OTG
  32         depends on USB
  33         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  34         select USB_PHY
  35         help
  36           If you say yes here you get support for the Philips ISP1301
  37           USB-On-The-Go transceiver working with the OMAP OTG controller.
  38           The ISP1301 is a full speed USB  transceiver which is used in
  39           products including H2, H3, and H4 development boards for Texas
  40           Instruments OMAP processors.
  41
  42           This driver can also be built as a module.  If so, the module
  43           will be called phy-isp1301-omap.
  44
  45 config KEYSTONE_USB_PHY
  46         tristate "Keystone USB PHY Driver"
  47         depends on ARCH_KEYSTONE || COMPILE_TEST
  48         depends on NOP_USB_XCEIV
  49         help
  50           Enable this to support Keystone USB phy. This driver provides
  51           interface to interact with USB 2.0 and USB 3.0 PHY that is part
  52           of the Keystone SOC.
  53
  54 config NOP_USB_XCEIV
  55         tristate "NOP USB Transceiver Driver"
  56         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
  57         select USB_PHY
  58         help
  59           This driver is to be used by all the usb transceiver which are either
  60           built-in with usb ip or which are autonomous and doesn't require any
  61           phy programming such as ISP1x04 etc.
  62
  63 config AM335X_CONTROL_USB
  64         tristate
  65
  66 config AM335X_PHY_USB
  67         tristate "AM335x USB PHY Driver"
  68         depends on ARM || COMPILE_TEST
  69         depends on NOP_USB_XCEIV
  70         select USB_PHY
  71         select AM335X_CONTROL_USB
  72         select USB_COMMON
  73         help
  74           This driver provides PHY support for that phy which part for the
  75           AM335x SoC.
  76
  77 config SAMSUNG_USBPHY
  78         tristate
  79         help
  80           Enable this to support Samsung USB phy helper driver for Samsung SoCs.
  81           This driver provides common interface to interact, for Samsung USB 2.0 PHY
  82           driver and later for Samsung USB 3.0 PHY driver.
  83
  84 config TWL6030_USB
  85         tristate "TWL6030 USB Transceiver Driver"
  86         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
  87         depends on OF
  88         help
  89           Enable this to support the USB OTG transceiver on TWL6030
  90           family chips. This TWL6030 transceiver has the VBUS and ID GND
  91           and OTG SRP events capabilities. For all other transceiver functionality
  92           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
  93           are hooked to this driver through platform_data structure.
  94           The definition of internal PHY APIs are in the mach-omap2 layer.
  95
  96 config USB_GPIO_VBUS
  97         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
  98         depends on GPIOLIB || COMPILE_TEST
  99         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 100         select USB_PHY
 101         help
 102           Provides simple GPIO VBUS sensing for controllers with an
 103           internal transceiver via the usb_phy interface, and
 104           optionally control of a D+ pullup GPIO as well as a VBUS
 105           current limit regulator.
 106
 107 config OMAP_OTG
 108         tristate "OMAP USB OTG controller driver"
 109         depends on ARCH_OMAP_OTG && EXTCON
 110         help
 111           Enable this to support some transceivers on OMAP1 platforms. OTG
 112           controller is needed to switch between host and peripheral modes.
 113
 114           This driver can also be built as a module. If so, the module
 115           will be called phy-omap-otg.
 116
 117 config TAHVO_USB
 118         tristate "Tahvo USB transceiver driver"
 119         depends on MFD_RETU && EXTCON
 120         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 121         select USB_PHY
 122         help
 123           Enable this to support USB transceiver on Tahvo. This is used
 124           at least on Nokia 770.
 125
 126 config TAHVO_USB_HOST_BY_DEFAULT
 127         depends on TAHVO_USB
 128         bool "Device in USB host mode by default"
 129         help
 130           Say Y here, if you want the device to enter USB host mode
 131           by default on bootup.
 132
 133 config USB_ISP1301
 134         tristate "NXP ISP1301 USB transceiver support"
 135         depends on USB || USB_GADGET
 136         depends on I2C
 137         select USB_PHY
 138         help
 139           Say Y here to add support for the NXP ISP1301 USB transceiver driver.
 140           This chip is typically used as USB transceiver for USB host, gadget
 141           and OTG drivers (to be selected separately).
 142
 143           To compile this driver as a module, choose M here: the
 144           module will be called phy-isp1301.
 145
 146 config USB_MSM_OTG
 147         tristate "Qualcomm on-chip USB OTG controller support"
 148         depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
 149         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 150         depends on RESET_CONTROLLER
 151         depends on EXTCON
 152         select USB_PHY
 153         help
 154           Enable this to support the USB OTG transceiver on Qualcomm chips. It
 155           handles PHY initialization, clock management, and workarounds
 156           required after resetting the hardware and power management.
 157           This driver is required even for peripheral only or host only
 158           mode configurations.
 159           This driver is not supported on boards like trout which
 160           has an external PHY.
 161
 162 config USB_QCOM_8X16_PHY
 163         tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
 164         depends on ARCH_QCOM || COMPILE_TEST
 165         depends on RESET_CONTROLLER && EXTCON
 166         select USB_PHY
 167         select USB_ULPI_VIEWPORT
 168         help
 169           Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
 170           It handles PHY initialization, clock management, power management,
 171           and workarounds required after resetting the hardware.
 172
 173           To compile this driver as a module, choose M here: the
 174           module will be called phy-qcom-8x16-usb.
 175
 176 config USB_MV_OTG
 177         tristate "Marvell USB OTG support"
 178         depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
 179         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 180         select USB_PHY
 181         help
 182           Say Y here if you want to build Marvell USB OTG transciever
 183           driver in kernel (including PXA and MMP series). This driver
 184           implements role switch between EHCI host driver and gadget driver.
 185
 186           To compile this driver as a module, choose M here.
 187
 188 config USB_MXS_PHY
 189         tristate "Freescale MXS USB PHY support"
 190         depends on ARCH_MXC || ARCH_MXS
 191         select STMP_DEVICE
 192         select USB_PHY
 193         help
 194           Enable this to support the Freescale MXS USB PHY.
 195
 196           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 197
 198 config USB_ULPI
 199         bool "Generic ULPI Transceiver Driver"
 200         depends on ARM || ARM64
 201         select USB_ULPI_VIEWPORT
 202         help
 203           Enable this to support ULPI connected USB OTG transceivers which
 204           are likely found on embedded boards.
 205
 206 config USB_ULPI_VIEWPORT
 207         bool
 208         help
 209           Provides read/write operations to the ULPI phy register set for
 210           controllers with a viewport register (e.g. Chipidea/ARC controllers).
 211
 212 endmenu