drivers/usb/phy/Kconfig

   1 #
   2 # Physical Layer USB driver configuration
   3 #
   4 menu "USB Physical Layer drivers"
   5
   6 config USB_PHY
   7         def_bool n
   8
   9 #
  10 # USB Transceiver Drivers
  11 #
  12 config AB8500_USB
  13         tristate "AB8500 USB Transceiver Driver"
  14         depends on AB8500_CORE
  15         select USB_PHY
  16         help
  17           Enable this to support the USB OTG transceiver in AB8500 chip.
  18           This transceiver supports high and full speed devices plus,
  19           in host mode, low speed.
  20
  21 config FSL_USB2_OTG
  22         bool "Freescale USB OTG Transceiver Driver"
  23         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
  24         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  25         select USB_PHY
  26         help
  27           Enable this to support Freescale USB OTG transceiver.
  28
  29 config ISP1301_OMAP
  30         tristate "Philips ISP1301 with OMAP OTG"
  31         depends on I2C && ARCH_OMAP_OTG
  32         depends on USB
  33         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  34         select USB_PHY
  35         help
  36           If you say yes here you get support for the Philips ISP1301
  37           USB-On-The-Go transceiver working with the OMAP OTG controller.
  38           The ISP1301 is a full speed USB  transceiver which is used in
  39           products including H2, H3, and H4 development boards for Texas
  40           Instruments OMAP processors.
  41
  42           This driver can also be built as a module.  If so, the module
  43           will be called phy-isp1301-omap.
  44
  45 config KEYSTONE_USB_PHY
  46         tristate "Keystone USB PHY Driver"
  47         depends on ARCH_KEYSTONE || COMPILE_TEST
  48         depends on NOP_USB_XCEIV
  49         help
  50           Enable this to support Keystone USB phy. This driver provides
  51           interface to interact with USB 2.0 and USB 3.0 PHY that is part
  52           of the Keystone SOC.
  53
  54 config NOP_USB_XCEIV
  55         tristate "NOP USB Transceiver Driver"
  56         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
  57         select USB_PHY
  58         help
  59           This driver is to be used by all the usb transceiver which are either
  60           built-in with usb ip or which are autonomous and doesn't require any
  61           phy programming such as ISP1x04 etc.
  62
  63 config AM335X_CONTROL_USB
  64         tristate
  65
  66 config AM335X_PHY_USB
  67         tristate "AM335x USB PHY Driver"
  68         depends on ARM || COMPILE_TEST
  69         depends on NOP_USB_XCEIV
  70         select USB_PHY
  71         select AM335X_CONTROL_USB
  72         select USB_COMMON
  73         help
  74           This driver provides PHY support for that phy which part for the
  75           AM335x SoC.
  76
  77 config TWL6030_USB
  78         tristate "TWL6030 USB Transceiver Driver"
  79         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
  80         depends on OF
  81         help
  82           Enable this to support the USB OTG transceiver on TWL6030
  83           family chips. This TWL6030 transceiver has the VBUS and ID GND
  84           and OTG SRP events capabilities. For all other transceiver functionality
  85           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
  86           are hooked to this driver through platform_data structure.
  87           The definition of internal PHY APIs are in the mach-omap2 layer.
  88
  89 config USB_GPIO_VBUS
  90         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
  91         depends on GPIOLIB || COMPILE_TEST
  92         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  93         select USB_PHY
  94         help
  95           Provides simple GPIO VBUS sensing for controllers with an
  96           internal transceiver via the usb_phy interface, and
  97           optionally control of a D+ pullup GPIO as well as a VBUS
  98           current limit regulator.
  99
 100 config OMAP_OTG
 101         tristate "OMAP USB OTG controller driver"
 102         depends on ARCH_OMAP_OTG && EXTCON
 103         help
 104           Enable this to support some transceivers on OMAP1 platforms. OTG
 105           controller is needed to switch between host and peripheral modes.
 106
 107           This driver can also be built as a module. If so, the module
 108           will be called phy-omap-otg.
 109
 110 config TAHVO_USB
 111         tristate "Tahvo USB transceiver driver"
 112         depends on MFD_RETU && EXTCON
 113         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 114         select USB_PHY
 115         help
 116           Enable this to support USB transceiver on Tahvo. This is used
 117           at least on Nokia 770.
 118
 119 config TAHVO_USB_HOST_BY_DEFAULT
 120         depends on TAHVO_USB
 121         bool "Device in USB host mode by default"
 122         help
 123           Say Y here, if you want the device to enter USB host mode
 124           by default on bootup.
 125
 126 config USB_ISP1301
 127         tristate "NXP ISP1301 USB transceiver support"
 128         depends on USB || USB_GADGET
 129         depends on I2C
 130         select USB_PHY
 131         help
 132           Say Y here to add support for the NXP ISP1301 USB transceiver driver.
 133           This chip is typically used as USB transceiver for USB host, gadget
 134           and OTG drivers (to be selected separately).
 135
 136           To compile this driver as a module, choose M here: the
 137           module will be called phy-isp1301.
 138
 139 config USB_MSM_OTG
 140         tristate "Qualcomm on-chip USB OTG controller support"
 141         depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
 142         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 143         depends on RESET_CONTROLLER
 144         depends on EXTCON
 145         select USB_PHY
 146         help
 147           Enable this to support the USB OTG transceiver on Qualcomm chips. It
 148           handles PHY initialization, clock management, and workarounds
 149           required after resetting the hardware and power management.
 150           This driver is required even for peripheral only or host only
 151           mode configurations.
 152           This driver is not supported on boards like trout which
 153           has an external PHY.
 154
 155 config USB_QCOM_8X16_PHY
 156         tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
 157         depends on ARCH_QCOM || COMPILE_TEST
 158         depends on RESET_CONTROLLER && EXTCON
 159         select USB_PHY
 160         select USB_ULPI_VIEWPORT
 161         help
 162           Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
 163           It handles PHY initialization, clock management, power management,
 164           and workarounds required after resetting the hardware.
 165
 166           To compile this driver as a module, choose M here: the
 167           module will be called phy-qcom-8x16-usb.
 168
 169 config USB_MV_OTG
 170         tristate "Marvell USB OTG support"
 171         depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
 172         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 173         select USB_PHY
 174         help
 175           Say Y here if you want to build Marvell USB OTG transciever
 176           driver in kernel (including PXA and MMP series). This driver
 177           implements role switch between EHCI host driver and gadget driver.
 178
 179           To compile this driver as a module, choose M here.
 180
 181 config USB_MXS_PHY
 182         tristate "Freescale MXS USB PHY support"
 183         depends on ARCH_MXC || ARCH_MXS
 184         select STMP_DEVICE
 185         select USB_PHY
 186         help
 187           Enable this to support the Freescale MXS USB PHY.
 188
 189           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 190
 191 config USB_ULPI
 192         bool "Generic ULPI Transceiver Driver"
 193         depends on ARM || ARM64
 194         select USB_ULPI_VIEWPORT
 195         help
 196           Enable this to support ULPI connected USB OTG transceivers which
 197           are likely found on embedded boards.
 198
 199 config USB_ULPI_VIEWPORT
 200         bool
 201         help
 202           Provides read/write operations to the ULPI phy register set for
 203           controllers with a viewport register (e.g. Chipidea/ARC controllers).
 204
 205 endmenu