drivers/usb/phy/Kconfig

   1 #
   2 # Physical Layer USB driver configuration
   3 #
   4 menu "USB Physical Layer drivers"
   5
   6 config USB_PHY
   7         def_bool n
   8
   9 #
  10 # USB Transceiver Drivers
  11 #
  12 config AB8500_USB
  13         tristate "AB8500 USB Transceiver Driver"
  14         depends on AB8500_CORE
  15         select USB_PHY
  16         help
  17           Enable this to support the USB OTG transceiver in AB8500 chip.
  18           This transceiver supports high and full speed devices plus,
  19           in host mode, low speed.
  20
  21 config FSL_USB2_OTG
  22         bool "Freescale USB OTG Transceiver Driver"
  23         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
  24         select USB_PHY
  25         help
  26           Enable this to support Freescale USB OTG transceiver.
  27
  28 config ISP1301_OMAP
  29         tristate "Philips ISP1301 with OMAP OTG"
  30         depends on I2C && ARCH_OMAP_OTG
  31         depends on USB
  32         select USB_PHY
  33         help
  34           If you say yes here you get support for the Philips ISP1301
  35           USB-On-The-Go transceiver working with the OMAP OTG controller.
  36           The ISP1301 is a full speed USB  transceiver which is used in
  37           products including H2, H3, and H4 development boards for Texas
  38           Instruments OMAP processors.
  39
  40           This driver can also be built as a module.  If so, the module
  41           will be called phy-isp1301-omap.
  42
  43 config KEYSTONE_USB_PHY
  44         tristate "Keystone USB PHY Driver"
  45         depends on ARCH_KEYSTONE || COMPILE_TEST
  46         select NOP_USB_XCEIV
  47         help
  48           Enable this to support Keystone USB phy. This driver provides
  49           interface to interact with USB 2.0 and USB 3.0 PHY that is part
  50           of the Keystone SOC.
  51
  52 config NOP_USB_XCEIV
  53         tristate "NOP USB Transceiver Driver"
  54         select USB_PHY
  55         help
  56           This driver is to be used by all the usb transceiver which are either
  57           built-in with usb ip or which are autonomous and doesn't require any
  58           phy programming such as ISP1x04 etc.
  59
  60 config AM335X_CONTROL_USB
  61         tristate
  62
  63 config AM335X_PHY_USB
  64         tristate "AM335x USB PHY Driver"
  65         depends on ARM || COMPILE_TEST
  66         select USB_PHY
  67         select AM335X_CONTROL_USB
  68         select NOP_USB_XCEIV
  69         help
  70           This driver provides PHY support for that phy which part for the
  71           AM335x SoC.
  72
  73 config SAMSUNG_USBPHY
  74         tristate
  75         help
  76           Enable this to support Samsung USB phy helper driver for Samsung SoCs.
  77           This driver provides common interface to interact, for Samsung USB 2.0 PHY
  78           driver and later for Samsung USB 3.0 PHY driver.
  79
  80 config TWL6030_USB
  81         tristate "TWL6030 USB Transceiver Driver"
  82         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
  83         help
  84           Enable this to support the USB OTG transceiver on TWL6030
  85           family chips. This TWL6030 transceiver has the VBUS and ID GND
  86           and OTG SRP events capabilities. For all other transceiver functionality
  87           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
  88           are hooked to this driver through platform_data structure.
  89           The definition of internal PHY APIs are in the mach-omap2 layer.
  90
  91 config USB_GPIO_VBUS
  92         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
  93         depends on GPIOLIB || COMPILE_TEST
  94         select USB_PHY
  95         help
  96           Provides simple GPIO VBUS sensing for controllers with an
  97           internal transceiver via the usb_phy interface, and
  98           optionally control of a D+ pullup GPIO as well as a VBUS
  99           current limit regulator.
 100
 101 config OMAP_OTG
 102         tristate "OMAP USB OTG controller driver"
 103         depends on ARCH_OMAP_OTG && EXTCON
 104         help
 105           Enable this to support some transceivers on OMAP1 platforms. OTG
 106           controller is needed to switch between host and peripheral modes.
 107
 108           This driver can also be built as a module. If so, the module
 109           will be called phy-omap-otg.
 110
 111 config TAHVO_USB
 112         tristate "Tahvo USB transceiver driver"
 113         depends on MFD_RETU && EXTCON
 114         select USB_PHY
 115         help
 116           Enable this to support USB transceiver on Tahvo. This is used
 117           at least on Nokia 770.
 118
 119 config TAHVO_USB_HOST_BY_DEFAULT
 120         depends on TAHVO_USB
 121         bool "Device in USB host mode by default"
 122         help
 123           Say Y here, if you want the device to enter USB host mode
 124           by default on bootup.
 125
 126 config USB_ISP1301
 127         tristate "NXP ISP1301 USB transceiver support"
 128         depends on USB || USB_GADGET
 129         depends on I2C
 130         select USB_PHY
 131         help
 132           Say Y here to add support for the NXP ISP1301 USB transceiver driver.
 133           This chip is typically used as USB transceiver for USB host, gadget
 134           and OTG drivers (to be selected separately).
 135
 136           To compile this driver as a module, choose M here: the
 137           module will be called phy-isp1301.
 138
 139 config USB_MSM_OTG
 140         tristate "Qualcomm on-chip USB OTG controller support"
 141         depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
 142         depends on RESET_CONTROLLER
 143         depends on EXTCON
 144         select USB_PHY
 145         help
 146           Enable this to support the USB OTG transceiver on Qualcomm chips. It
 147           handles PHY initialization, clock management, and workarounds
 148           required after resetting the hardware and power management.
 149           This driver is required even for peripheral only or host only
 150           mode configurations.
 151           This driver is not supported on boards like trout which
 152           has an external PHY.
 153
 154 config USB_QCOM_8X16_PHY
 155         tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
 156         depends on ARCH_QCOM || COMPILE_TEST
 157         depends on RESET_CONTROLLER && EXTCON
 158         select USB_PHY
 159         select USB_ULPI_VIEWPORT
 160         help
 161           Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
 162           It handles PHY initialization, clock management, power management,
 163           and workarounds required after resetting the hardware.
 164
 165           To compile this driver as a module, choose M here: the
 166           module will be called phy-qcom-8x16-usb.
 167
 168 config USB_MV_OTG
 169         tristate "Marvell USB OTG support"
 170         depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
 171         select USB_PHY
 172         help
 173           Say Y here if you want to build Marvell USB OTG transciever
 174           driver in kernel (including PXA and MMP series). This driver
 175           implements role switch between EHCI host driver and gadget driver.
 176
 177           To compile this driver as a module, choose M here.
 178
 179 config USB_MXS_PHY
 180         tristate "Freescale MXS USB PHY support"
 181         depends on ARCH_MXC || ARCH_MXS
 182         select STMP_DEVICE
 183         select USB_PHY
 184         help
 185           Enable this to support the Freescale MXS USB PHY.
 186
 187           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 188
 189 config USB_RCAR_PHY
 190         tristate "Renesas R-Car USB PHY support"
 191         depends on USB || USB_GADGET
 192         depends on ARCH_R8A7778 || ARCH_R8A7779 || COMPILE_TEST
 193         select USB_PHY
 194         help
 195           Say Y here to add support for the Renesas R-Car USB common PHY driver.
 196           This chip is typically used as USB PHY for USB host, gadget.
 197           This driver supports R8A7778 and R8A7779.
 198
 199           To compile this driver as a module, choose M here: the
 200           module will be called phy-rcar-usb.
 201
 202 config USB_ULPI
 203         bool "Generic ULPI Transceiver Driver"
 204         depends on ARM || ARM64
 205         select USB_ULPI_VIEWPORT
 206         help
 207           Enable this to support ULPI connected USB OTG transceivers which
 208           are likely found on embedded boards.
 209
 210 config USB_ULPI_VIEWPORT
 211         bool
 212         help
 213           Provides read/write operations to the ULPI phy register set for
 214           controllers with a viewport register (e.g. Chipidea/ARC controllers).
 215
 216 endmenu