drivers/usb/serial/io_16654.h

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /************************************************************************
   3  *
   4  *      16654.H         Definitions for 16C654 UART used on EdgePorts
   5  *
   6  *      Copyright (C) 1998 Inside Out Networks, Inc.
   7  *
   8  ************************************************************************/
   9
  10 #if !defined(_16654_H)
  11 #define _16654_H
  12
  13 /************************************************************************
  14  *
  15  *                      D e f i n e s   /   T y p e d e f s
  16  *
  17  ************************************************************************/
  18
  19         //
  20         // UART register numbers
  21         // Numbers 0-7 are passed to the Edgeport directly. Numbers 8 and
  22         // above are used internally to indicate that we must enable access
  23         // to them via LCR bit 0x80 or LCR = 0xBF.
  24         // The register number sent to the Edgeport is then (x & 0x7).
  25         //
  26         // Driver must not access registers that affect operation of the
  27         // the EdgePort firmware -- that includes THR, RHR, IER, FCR.
  28
  29
  30 #define THR                     0       // ! Transmit Holding Register (Write)
  31 #define RDR                     0       // ! Receive Holding Register (Read)
  32 #define IER                     1       // ! Interrupt Enable Register
  33 #define FCR                     2       // ! Fifo Control Register (Write)
  34 #define ISR                     2       // Interrupt Status Register (Read)
  35 #define LCR                     3       // Line Control Register
  36 #define MCR                     4       // Modem Control Register
  37 #define LSR                     5       // Line Status Register
  38 #define MSR                     6       // Modem Status Register
  39 #define SPR                     7       // ScratchPad Register
  40 #define DLL                     8       // Bank2[ 0 ] Divisor Latch LSB
  41 #define DLM                     9       // Bank2[ 1 ] Divisor Latch MSB
  42 #define EFR                     10      // Bank2[ 2 ] Extended Function Register
  43 //efine unused                  11      // Bank2[ 3 ]
  44 #define XON1                    12      // Bank2[ 4 ] Xon-1
  45 #define XON2                    13      // Bank2[ 5 ] Xon-2
  46 #define XOFF1                   14      // Bank2[ 6 ] Xoff-1
  47 #define XOFF2                   15      // Bank2[ 7 ] Xoff-2
  48
  49 #define NUM_16654_REGS          16
  50
  51 #define IS_REG_2ND_BANK(x)      ((x) >= 8)
  52
  53         //
  54         // Bit definitions for each register
  55         //
  56
  57 #define IER_RX                  0x01    // Enable receive interrupt
  58 #define IER_TX                  0x02    // Enable transmit interrupt
  59 #define IER_RXS                 0x04    // Enable receive status interrupt
  60 #define IER_MDM                 0x08    // Enable modem status interrupt
  61 #define IER_SLEEP               0x10    // Enable sleep mode
  62 #define IER_XOFF                0x20    // Enable s/w flow control (XOFF) interrupt
  63 #define IER_RTS                 0x40    // Enable RTS interrupt
  64 #define IER_CTS                 0x80    // Enable CTS interrupt
  65 #define IER_ENABLE_ALL          0xFF    // Enable all ints
  66
  67
  68 #define FCR_FIFO_EN             0x01    // Enable FIFOs
  69 #define FCR_RXCLR               0x02    // Reset Rx FIFO
  70 #define FCR_TXCLR               0x04    // Reset Tx FIFO
  71 #define FCR_DMA_BLK             0x08    // Enable DMA block mode
  72 #define FCR_TX_LEVEL_MASK       0x30    // Mask for Tx FIFO Level
  73 #define FCR_TX_LEVEL_8          0x00    // Tx FIFO Level =  8 bytes
  74 #define FCR_TX_LEVEL_16         0x10    // Tx FIFO Level = 16 bytes
  75 #define FCR_TX_LEVEL_32         0x20    // Tx FIFO Level = 32 bytes
  76 #define FCR_TX_LEVEL_56         0x30    // Tx FIFO Level = 56 bytes
  77 #define FCR_RX_LEVEL_MASK       0xC0    // Mask for Rx FIFO Level
  78 #define FCR_RX_LEVEL_8          0x00    // Rx FIFO Level =  8 bytes
  79 #define FCR_RX_LEVEL_16         0x40    // Rx FIFO Level = 16 bytes
  80 #define FCR_RX_LEVEL_56         0x80    // Rx FIFO Level = 56 bytes
  81 #define FCR_RX_LEVEL_60         0xC0    // Rx FIFO Level = 60 bytes
  82
  83
  84 #define ISR_INT_MDM_STATUS      0x00    // Modem status int pending
  85 #define ISR_INT_NONE            0x01    // No interrupt pending
  86 #define ISR_INT_TXRDY           0x02    // Tx ready int pending
  87 #define ISR_INT_RXRDY           0x04    // Rx ready int pending
  88 #define ISR_INT_LINE_STATUS     0x06    // Line status int pending
  89 #define ISR_INT_RX_TIMEOUT      0x0C    // Rx timeout int pending
  90 #define ISR_INT_RX_XOFF         0x10    // Rx Xoff int pending
  91 #define ISR_INT_RTS_CTS         0x20    // RTS/CTS change int pending
  92 #define ISR_FIFO_ENABLED        0xC0    // Bits set if FIFOs enabled
  93 #define ISR_INT_BITS_MASK       0x3E    // Mask to isolate valid int causes
  94
  95
  96 #define LCR_BITS_5              0x00    // 5 bits/char
  97 #define LCR_BITS_6              0x01    // 6 bits/char
  98 #define LCR_BITS_7              0x02    // 7 bits/char
  99 #define LCR_BITS_8              0x03    // 8 bits/char
 100 #define LCR_BITS_MASK           0x03    // Mask for bits/char field
 101
 102 #define LCR_STOP_1              0x00    // 1 stop bit
 103 #define LCR_STOP_1_5            0x04    // 1.5 stop bits (if 5   bits/char)
 104 #define LCR_STOP_2              0x04    // 2 stop bits   (if 6-8 bits/char)
 105 #define LCR_STOP_MASK           0x04    // Mask for stop bits field
 106
 107 #define LCR_PAR_NONE            0x00    // No parity
 108 #define LCR_PAR_ODD             0x08    // Odd parity
 109 #define LCR_PAR_EVEN            0x18    // Even parity
 110 #define LCR_PAR_MARK            0x28    // Force parity bit to 1
 111 #define LCR_PAR_SPACE           0x38    // Force parity bit to 0
 112 #define LCR_PAR_MASK            0x38    // Mask for parity field
 113
 114 #define LCR_SET_BREAK           0x40    // Set Break condition
 115 #define LCR_DL_ENABLE           0x80    // Enable access to divisor latch
 116
 117 #define LCR_ACCESS_EFR          0xBF    // Load this value to access DLL,DLM,
 118                                         // and also the '654-only registers
 119                                         // EFR, XON1, XON2, XOFF1, XOFF2
 120
 121
 122 #define MCR_DTR                 0x01    // Assert DTR
 123 #define MCR_RTS                 0x02    // Assert RTS
 124 #define MCR_OUT1                0x04    // Loopback only: Sets state of RI
 125 #define MCR_MASTER_IE           0x08    // Enable interrupt outputs
 126 #define MCR_LOOPBACK            0x10    // Set internal (digital) loopback mode
 127 #define MCR_XON_ANY             0x20    // Enable any char to exit XOFF mode
 128 #define MCR_IR_ENABLE           0x40    // Enable IrDA functions
 129 #define MCR_BRG_DIV_4           0x80    // Divide baud rate clk by /4 instead of /1
 130
 131
 132 #define LSR_RX_AVAIL            0x01    // Rx data available
 133 #define LSR_OVER_ERR            0x02    // Rx overrun
 134 #define LSR_PAR_ERR             0x04    // Rx parity error
 135 #define LSR_FRM_ERR             0x08    // Rx framing error
 136 #define LSR_BREAK               0x10    // Rx break condition detected
 137 #define LSR_TX_EMPTY            0x20    // Tx Fifo empty
 138 #define LSR_TX_ALL_EMPTY        0x40    // Tx Fifo and shift register empty
 139 #define LSR_FIFO_ERR            0x80    // Rx Fifo contains at least 1 erred char
 140
 141
 142 #define EDGEPORT_MSR_DELTA_CTS  0x01    // CTS changed from last read
 143 #define EDGEPORT_MSR_DELTA_DSR  0x02    // DSR changed from last read
 144 #define EDGEPORT_MSR_DELTA_RI   0x04    // RI  changed from 0 -> 1
 145 #define EDGEPORT_MSR_DELTA_CD   0x08    // CD  changed from last read
 146 #define EDGEPORT_MSR_CTS        0x10    // Current state of CTS
 147 #define EDGEPORT_MSR_DSR        0x20    // Current state of DSR
 148 #define EDGEPORT_MSR_RI         0x40    // Current state of RI
 149 #define EDGEPORT_MSR_CD         0x80    // Current state of CD
 150
 151
 152
 153                                         //      Tx              Rx
 154                                         //-------------------------------
 155 #define EFR_SWFC_NONE           0x00    //      None            None
 156 #define EFR_SWFC_RX1            0x02    //      None            XOFF1
 157 #define EFR_SWFC_RX2            0x01    //      None            XOFF2
 158 #define EFR_SWFC_RX12           0x03    //      None            XOFF1 & XOFF2
 159 #define EFR_SWFC_TX1            0x08    //      XOFF1           None
 160 #define EFR_SWFC_TX1_RX1        0x0a    //      XOFF1           XOFF1
 161 #define EFR_SWFC_TX1_RX2        0x09    //      XOFF1           XOFF2
 162 #define EFR_SWFC_TX1_RX12       0x0b    //      XOFF1           XOFF1 & XOFF2
 163 #define EFR_SWFC_TX2            0x04    //      XOFF2           None
 164 #define EFR_SWFC_TX2_RX1        0x06    //      XOFF2           XOFF1
 165 #define EFR_SWFC_TX2_RX2        0x05    //      XOFF2           XOFF2
 166 #define EFR_SWFC_TX2_RX12       0x07    //      XOFF2           XOFF1 & XOFF2
 167 #define EFR_SWFC_TX12           0x0c    //      XOFF1 & XOFF2   None
 168 #define EFR_SWFC_TX12_RX1       0x0e    //      XOFF1 & XOFF2   XOFF1
 169 #define EFR_SWFC_TX12_RX2       0x0d    //      XOFF1 & XOFF2   XOFF2
 170 #define EFR_SWFC_TX12_RX12      0x0f    //      XOFF1 & XOFF2   XOFF1 & XOFF2
 171
 172 #define EFR_TX_FC_MASK          0x0c    // Mask to isolate Rx flow control
 173 #define EFR_TX_FC_NONE          0x00    // No Tx Xon/Xoff flow control
 174 #define EFR_TX_FC_X1            0x08    // Transmit Xon1/Xoff1
 175 #define EFR_TX_FC_X2            0x04    // Transmit Xon2/Xoff2
 176 #define EFR_TX_FC_X1_2          0x0c    // Transmit Xon1&2/Xoff1&2
 177
 178 #define EFR_RX_FC_MASK          0x03    // Mask to isolate Rx flow control
 179 #define EFR_RX_FC_NONE          0x00    // No Rx Xon/Xoff flow control
 180 #define EFR_RX_FC_X1            0x02    // Receiver compares Xon1/Xoff1
 181 #define EFR_RX_FC_X2            0x01    // Receiver compares Xon2/Xoff2
 182 #define EFR_RX_FC_X1_2          0x03    // Receiver compares Xon1&2/Xoff1&2
 183
 184
 185 #define EFR_SWFC_MASK           0x0F    // Mask for software flow control field
 186 #define EFR_ENABLE_16654        0x10    // Enable 16C654 features
 187 #define EFR_SPEC_DETECT         0x20    // Enable special character detect interrupt
 188 #define EFR_AUTO_RTS            0x40    // Use RTS for Rx flow control
 189 #define EFR_AUTO_CTS            0x80    // Use CTS for Tx flow control
 190
 191 #endif  // if !defined(_16654_H)
 192