drivers/video/fbdev/omap2/omapfb/dss/Kconfig

   1 config FB_OMAP2_DSS_INIT
   2         bool
   3
   4 config FB_OMAP2_DSS
   5         tristate
   6         select VIDEOMODE_HELPERS
   7         select FB_OMAP2_DSS_INIT
   8         select HDMI
   9
  10 config FB_OMAP2_DSS_DEBUG
  11         bool "Debug support"
  12         default n
  13         help
  14           This enables printing of debug messages. Alternatively, debug messages
  15           can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting
  16           appropriate flags in <debugfs>/dynamic_debug/control.
  17
  18 config FB_OMAP2_DSS_DEBUGFS
  19         bool "Debugfs filesystem support"
  20         depends on DEBUG_FS
  21         default n
  22         help
  23           This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables
  24           querying about clock configuration and register configuration of dss,
  25           dispc, dsi, hdmi and rfbi.
  26
  27 config FB_OMAP2_DSS_COLLECT_IRQ_STATS
  28         bool "Collect DSS IRQ statistics"
  29         depends on FB_OMAP2_DSS_DEBUGFS
  30         default n
  31         help
  32           Collect DSS IRQ statistics, printable via debugfs.
  33
  34           The statistics can be found from
  35           <debugfs>/omapdss/dispc_irq for DISPC interrupts, and
  36           <debugfs>/omapdss/dsi_irq for DSI interrupts.
  37
  38 config FB_OMAP2_DSS_DPI
  39         bool "DPI support"
  40         default y
  41         help
  42           DPI Interface. This is the Parallel Display Interface.
  43
  44 config FB_OMAP2_DSS_RFBI
  45         bool "RFBI support"
  46         depends on BROKEN
  47         default n
  48         help
  49           MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas
  50           Instrument's terminology).
  51
  52           DBI is a bus between the host processor and a peripheral,
  53           such as a display or a framebuffer chip.
  54
  55           See http://www.mipi.org/ for DBI specifications.
  56
  57 config FB_OMAP2_DSS_VENC
  58         bool "VENC support"
  59         default y
  60         help
  61           OMAP Video Encoder support for S-Video and composite TV-out.
  62
  63 config FB_OMAP2_DSS_HDMI_COMMON
  64         bool
  65
  66 config FB_OMAP4_DSS_HDMI
  67         bool "HDMI support for OMAP4"
  68         default y
  69         select FB_OMAP2_DSS_HDMI_COMMON
  70         help
  71           HDMI support for OMAP4 based SoCs.
  72
  73 config FB_OMAP5_DSS_HDMI
  74         bool "HDMI support for OMAP5"
  75         default n
  76         select FB_OMAP2_DSS_HDMI_COMMON
  77         help
  78           HDMI Interface for OMAP5 and similar cores. This adds the High
  79           Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI
  80           specification.
  81
  82 config FB_OMAP2_DSS_SDI
  83         bool "SDI support"
  84         default n
  85         help
  86           SDI (Serial Display Interface) support.
  87
  88           SDI is a high speed one-way display serial bus between the host
  89           processor and a display.
  90
  91 config FB_OMAP2_DSS_DSI
  92         bool "DSI support"
  93         default n
  94         help
  95           MIPI DSI (Display Serial Interface) support.
  96
  97           DSI is a high speed half-duplex serial interface between the host
  98           processor and a peripheral, such as a display or a framebuffer chip.
  99
 100           See http://www.mipi.org/ for DSI specifications.
 101
 102 config FB_OMAP2_DSS_MIN_FCK_PER_PCK
 103         int "Minimum FCK/PCK ratio (for scaling)"
 104         range 0 32
 105         default 0
 106         help
 107           This can be used to adjust the minimum FCK/PCK ratio.
 108
 109           With this you can make sure that DISPC FCK is at least
 110           n x PCK. Video plane scaling requires higher FCK than
 111           normally.
 112
 113           If this is set to 0, there's no extra constraint on the
 114           DISPC FCK. However, the FCK will at minimum be
 115           2xPCK (if active matrix) or 3xPCK (if passive matrix).
 116
 117           Max FCK is 173MHz, so this doesn't work if your PCK
 118           is very high.
 119
 120 config FB_OMAP2_DSS_SLEEP_AFTER_VENC_RESET
 121         bool "Sleep 20ms after VENC reset"
 122         default y
 123         help
 124           There is a 20ms sleep after VENC reset which seemed to fix the
 125           reset. The reason for the bug is unclear, and it's also unclear
 126           on what platforms this happens.
 127
 128           This option enables the sleep, and is enabled by default. You can
 129           disable the sleep if it doesn't cause problems on your platform.