drivers/w1/slaves/Kconfig

   1 #
   2 # 1-wire slaves configuration
   3 #
   4
   5 menu "1-wire Slaves"
   6
   7 config W1_SLAVE_THERM
   8         tristate "Thermal family implementation"
   9         help
  10           Say Y here if you want to connect 1-wire thermal sensors to your
  11           wire.
  12
  13 config W1_SLAVE_SMEM
  14         tristate "Simple 64bit memory family implementation"
  15         help
  16           Say Y here if you want to connect 1-wire
  17           simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
  18
  19 config W1_SLAVE_DS2405
  20         tristate "DS2405 Addressable Switch"
  21         help
  22           Say Y or M here if you want to use a DS2405 1-wire
  23           single-channel addressable switch.
  24           This device can also work as a single-channel
  25           binary remote sensor.
  26
  27 config W1_SLAVE_DS2408
  28         tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
  29         help
  30           Say Y here if you want to use a 1-wire
  31           DS2408 8-Channel Addressable Switch device support
  32
  33 config W1_SLAVE_DS2408_READBACK
  34         bool "Read-back values written to DS2408's output register"
  35         depends on W1_SLAVE_DS2408
  36         default y
  37         help
  38           Enabling this will cause the driver to read back the values written
  39           to the chip's output register in order to detect errors.
  40
  41           This is slower but useful when debugging chips and/or busses.
  42
  43 config W1_SLAVE_DS2413
  44         tristate "Dual Channel Addressable Switch 0x3a family support (DS2413)"
  45         help
  46           Say Y here if you want to use a 1-wire
  47           DS2413 Dual Channel Addressable Switch device support
  48
  49 config W1_SLAVE_DS2406
  50         tristate "Dual Channel Addressable Switch 0x12 family support (DS2406)"
  51         select CRC16
  52         help
  53           Say Y or M here if you want to use a 1-wire
  54           DS2406 Dual Channel Addressable Switch.  EPROM read/write
  55           support for these devices is not implemented.
  56
  57 config W1_SLAVE_DS2423
  58         tristate "Counter 1-wire device (DS2423)"
  59         select CRC16
  60         help
  61           If you enable this you can read the counter values available
  62           in the DS2423 chipset from the w1_slave file under the
  63           sys file system.
  64
  65           Say Y here if you want to use a 1-wire
  66           counter family device (DS2423).
  67
  68 config W1_SLAVE_DS2805
  69         tristate "112-byte EEPROM support (DS28E05)"
  70         help
  71           Say Y here if you want to use a 1-wire
  72           is a 112-byte user-programmable EEPROM is
  73           organized as 7 pages of 16 bytes each with 64bit
  74           unique number. Requires OverDrive Speed to talk to.
  75
  76 config W1_SLAVE_DS2431
  77         tristate "1kb EEPROM family support (DS2431)"
  78         help
  79           Say Y here if you want to use a 1-wire
  80           1kb EEPROM family device (DS2431)
  81
  82 config W1_SLAVE_DS2433
  83         tristate "4kb EEPROM family support (DS2433)"
  84         help
  85           Say Y here if you want to use a 1-wire
  86           4kb EEPROM family device (DS2433).
  87
  88 config W1_SLAVE_DS2433_CRC
  89         bool "Protect DS2433 data with a CRC16"
  90         depends on W1_SLAVE_DS2433
  91         select CRC16
  92         help
  93           Say Y here to protect DS2433 data with a CRC16.
  94           Each block has 30 bytes of data and a two byte CRC16.
  95           Full block writes are only allowed if the CRC is valid.
  96
  97 config W1_SLAVE_DS2438
  98         tristate "DS2438 Smart Battery Monitor 0x26 family support"
  99         help
 100           Say Y here if you want to use a 1-wire
 101           DS2438 Smart Battery Monitor device support
 102
 103 config W1_SLAVE_DS2760
 104         tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
 105         help
 106           If you enable this you will have the DS2760 battery monitor
 107           chip support.
 108
 109           The battery monitor chip is used in many batteries/devices
 110           as the one who is responsible for charging/discharging/monitoring
 111           Li+ batteries.
 112
 113           If you are unsure, say N.
 114
 115 config W1_SLAVE_DS2780
 116         tristate "Dallas 2780 battery monitor chip"
 117         help
 118           If you enable this you will have the DS2780 battery monitor
 119           chip support.
 120
 121           The battery monitor chip is used in many batteries/devices
 122           as the one who is responsible for charging/discharging/monitoring
 123           Li+ batteries.
 124
 125           If you are unsure, say N.
 126
 127 config W1_SLAVE_DS2781
 128         tristate "Dallas 2781 battery monitor chip"
 129         help
 130           If you enable this you will have the DS2781 battery monitor
 131           chip support.
 132
 133           The battery monitor chip is used in many batteries/devices
 134           as the one who is responsible for charging/discharging/monitoring
 135           Li+ batteries.
 136
 137           If you are unsure, say N.
 138
 139 config W1_SLAVE_DS28E04
 140         tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)"
 141         select CRC16
 142         help
 143           If you enable this you will have the DS28E04-100
 144           chip support.
 145
 146           Say Y here if you want to use a 1-wire
 147           4kb EEPROM with PIO family device (DS28E04).
 148
 149           If you are unsure, say N.
 150
 151 endmenu