fpu/softfloat-specialize.c.inc

   1 /*
   2  * QEMU float support
   3  *
   4  * The code in this source file is derived from release 2a of the SoftFloat
   5  * IEC/IEEE Floating-point Arithmetic Package. Those parts of the code (and
   6  * some later contributions) are provided under that license, as detailed below.
   7  * It has subsequently been modified by contributors to the QEMU Project,
   8  * so some portions are provided under:
   9  *  the SoftFloat-2a license
  10  *  the BSD license
  11  *  GPL-v2-or-later
  12  *
  13  * Any future contributions to this file after December 1st 2014 will be
  14  * taken to be licensed under the Softfloat-2a license unless specifically
  15  * indicated otherwise.
  16  */
  17
  18 /*
  19 ===============================================================================
  20 This C source fragment is part of the SoftFloat IEC/IEEE Floating-point
  21 Arithmetic Package, Release 2a.
  22
  23 Written by John R. Hauser.  This work was made possible in part by the
  24 International Computer Science Institute, located at Suite 600, 1947 Center
  25 Street, Berkeley, California 94704.  Funding was partially provided by the
  26 National Science Foundation under grant MIP-9311980.  The original version
  27 of this code was written as part of a project to build a fixed-point vector
  28 processor in collaboration with the University of California at Berkeley,
  29 overseen by Profs. Nelson Morgan and John Wawrzynek.  More information
  30 is available through the Web page `http://HTTP.CS.Berkeley.EDU/~jhauser/
  31 arithmetic/SoftFloat.html'.
  32
  33 THIS SOFTWARE IS DISTRIBUTED AS IS, FOR FREE.  Although reasonable effort
  34 has been made to avoid it, THIS SOFTWARE MAY CONTAIN FAULTS THAT WILL AT
  35 TIMES RESULT IN INCORRECT BEHAVIOR.  USE OF THIS SOFTWARE IS RESTRICTED TO
  36 PERSONS AND ORGANIZATIONS WHO CAN AND WILL TAKE FULL RESPONSIBILITY FOR ANY
  37 AND ALL LOSSES, COSTS, OR OTHER PROBLEMS ARISING FROM ITS USE.
  38
  39 Derivative works are acceptable, even for commercial purposes, so long as
  40 (1) they include prominent notice that the work is derivative, and (2) they
  41 include prominent notice akin to these four paragraphs for those parts of
  42 this code that are retained.
  43
  44 ===============================================================================
  45 */
  46
  47 /* BSD licensing:
  48  * Copyright (c) 2006, Fabrice Bellard
  49  * All rights reserved.
  50  *
  51  * Redistribution and use in source and binary forms, with or without
  52  * modification, are permitted provided that the following conditions are met:
  53  *
  54  * 1. Redistributions of source code must retain the above copyright notice,
  55  * this list of conditions and the following disclaimer.
  56  *
  57  * 2. Redistributions in binary form must reproduce the above copyright notice,
  58  * this list of conditions and the following disclaimer in the documentation
  59  * and/or other materials provided with the distribution.
  60  *
  61  * 3. Neither the name of the copyright holder nor the names of its contributors
  62  * may be used to endorse or promote products derived from this software without
  63  * specific prior written permission.
  64  *
  65  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  66  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  67  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  68  * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
  69  * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
  70  * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
  71  * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
  72  * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
  73  * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  74  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  75  * THE POSSIBILITY OF SUCH DAMAGE.
  76  */
  77
  78 /* Portions of this work are licensed under the terms of the GNU GPL,
  79  * version 2 or later. See the COPYING file in the top-level directory.
  80  */
  81
  82 /*
  83  * Define whether architecture deviates from IEEE in not supporting
  84  * signaling NaNs (so all NaNs are treated as quiet).
  85  */
  86 static inline bool no_signaling_nans(float_status *status)
  87 {
  88 #if defined(TARGET_XTENSA)
  89     return status->no_signaling_nans;
  90 #else
  91     return false;
  92 #endif
  93 }
  94
  95 /* Define how the architecture discriminates signaling NaNs.
  96  * This done with the most significant bit of the fraction.
  97  * In IEEE 754-1985 this was implementation defined, but in IEEE 754-2008
  98  * the msb must be zero.  MIPS is (so far) unique in supporting both the
  99  * 2008 revision and backward compatibility with their original choice.
 100  * Thus for MIPS we must make the choice at runtime.
 101  */
 102 static inline bool snan_bit_is_one(float_status *status)
 103 {
 104 #if defined(TARGET_MIPS)
 105     return status->snan_bit_is_one;
 106 #elif defined(TARGET_HPPA) || defined(TARGET_SH4)
 107     return 1;
 108 #else
 109     return 0;
 110 #endif
 111 }
 112
 113 /*----------------------------------------------------------------------------
 114 | For the deconstructed floating-point with fraction FRAC, return true
 115 | if the fraction represents a signalling NaN; otherwise false.
 116 *----------------------------------------------------------------------------*/
 117
 118 static bool parts_is_snan_frac(uint64_t frac, float_status *status)
 119 {
 120     if (no_signaling_nans(status)) {
 121         return false;
 122     } else {
 123         bool msb = extract64(frac, DECOMPOSED_BINARY_POINT - 1, 1);
 124         return msb == snan_bit_is_one(status);
 125     }
 126 }
 127
 128 /*----------------------------------------------------------------------------
 129 | The pattern for a default generated deconstructed floating-point NaN.
 130 *----------------------------------------------------------------------------*/
 131
 132 static void parts64_default_nan(FloatParts64 *p, float_status *status)
 133 {
 134     bool sign = 0;
 135     uint64_t frac;
 136
 137 #if defined(TARGET_SPARC) || defined(TARGET_M68K)
 138     /* !snan_bit_is_one, set all bits */
 139     frac = (1ULL << DECOMPOSED_BINARY_POINT) - 1;
 140 #elif defined(TARGET_I386) || defined(TARGET_X86_64) \
 141     || defined(TARGET_MICROBLAZE)
 142     /* !snan_bit_is_one, set sign and msb */
 143     frac = 1ULL << (DECOMPOSED_BINARY_POINT - 1);
 144     sign = 1;
 145 #elif defined(TARGET_HPPA)
 146     /* snan_bit_is_one, set msb-1.  */
 147     frac = 1ULL << (DECOMPOSED_BINARY_POINT - 2);
 148 #elif defined(TARGET_HEXAGON)
 149     sign = 1;
 150     frac = ~0ULL;
 151 #else
 152     /*
 153      * This case is true for Alpha, ARM, MIPS, OpenRISC, PPC, RISC-V,
 154      * S390, SH4, TriCore, and Xtensa.  Our other supported targets,
 155      * CRIS, Nios2, and Tile, do not have floating-point.
 156      */
 157     if (snan_bit_is_one(status)) {
 158         /* set all bits other than msb */
 159         frac = (1ULL << (DECOMPOSED_BINARY_POINT - 1)) - 1;
 160     } else {
 161         /* set msb */
 162         frac = 1ULL << (DECOMPOSED_BINARY_POINT - 1);
 163     }
 164 #endif
 165
 166     *p = (FloatParts64) {
 167         .cls = float_class_qnan,
 168         .sign = sign,
 169         .exp = INT_MAX,
 170         .frac = frac
 171     };
 172 }
 173
 174 static void parts128_default_nan(FloatParts128 *p, float_status *status)
 175 {
 176     /*
 177      * Extrapolate from the choices made by parts64_default_nan to fill
 178      * in the quad-floating format.  If the low bit is set, assume we
 179      * want to set all non-snan bits.
 180      */
 181     FloatParts64 p64;
 182     parts64_default_nan(&p64, status);
 183
 184     *p = (FloatParts128) {
 185         .cls = float_class_qnan,
 186         .sign = p64.sign,
 187         .exp = INT_MAX,
 188         .frac_hi = p64.frac,
 189         .frac_lo = -(p64.frac & 1)
 190     };
 191 }
 192
 193 /*----------------------------------------------------------------------------
 194 | Returns a quiet NaN from a signalling NaN for the deconstructed
 195 | floating-point parts.
 196 *----------------------------------------------------------------------------*/
 197
 198 static uint64_t parts_silence_nan_frac(uint64_t frac, float_status *status)
 199 {
 200     g_assert(!no_signaling_nans(status));
 201
 202     /* The only snan_bit_is_one target without default_nan_mode is HPPA. */
 203     if (snan_bit_is_one(status)) {
 204         frac &= ~(1ULL << (DECOMPOSED_BINARY_POINT - 1));
 205         frac |= 1ULL << (DECOMPOSED_BINARY_POINT - 2);
 206     } else {
 207         frac |= 1ULL << (DECOMPOSED_BINARY_POINT - 1);
 208     }
 209     return frac;
 210 }
 211
 212 static void parts64_silence_nan(FloatParts64 *p, float_status *status)
 213 {
 214     p->frac = parts_silence_nan_frac(p->frac, status);
 215     p->cls = float_class_qnan;
 216 }
 217
 218 static void parts128_silence_nan(FloatParts128 *p, float_status *status)
 219 {
 220     p->frac_hi = parts_silence_nan_frac(p->frac_hi, status);
 221     p->cls = float_class_qnan;
 222 }
 223
 224 /*----------------------------------------------------------------------------
 225 | The pattern for a default generated extended double-precision NaN.
 226 *----------------------------------------------------------------------------*/
 227 floatx80 floatx80_default_nan(float_status *status)
 228 {
 229     floatx80 r;
 230
 231     /* None of the targets that have snan_bit_is_one use floatx80.  */
 232     assert(!snan_bit_is_one(status));
 233 #if defined(TARGET_M68K)
 234     r.low = UINT64_C(0xFFFFFFFFFFFFFFFF);
 235     r.high = 0x7FFF;
 236 #else
 237     /* X86 */
 238     r.low = UINT64_C(0xC000000000000000);
 239     r.high = 0xFFFF;
 240 #endif
 241     return r;
 242 }
 243
 244 /*----------------------------------------------------------------------------
 245 | The pattern for a default generated extended double-precision inf.
 246 *----------------------------------------------------------------------------*/
 247
 248 #define floatx80_infinity_high 0x7FFF
 249 #if defined(TARGET_M68K)
 250 #define floatx80_infinity_low  UINT64_C(0x0000000000000000)
 251 #else
 252 #define floatx80_infinity_low  UINT64_C(0x8000000000000000)
 253 #endif
 254
 255 const floatx80 floatx80_infinity
 256     = make_floatx80_init(floatx80_infinity_high, floatx80_infinity_low);
 257
 258 /*----------------------------------------------------------------------------
 259 | Returns 1 if the half-precision floating-point value `a' is a quiet
 260 | NaN; otherwise returns 0.
 261 *----------------------------------------------------------------------------*/
 262
 263 bool float16_is_quiet_nan(float16 a_, float_status *status)
 264 {
 265     if (no_signaling_nans(status)) {
 266         return float16_is_any_nan(a_);
 267     } else {
 268         uint16_t a = float16_val(a_);
 269         if (snan_bit_is_one(status)) {
 270             return (((a >> 9) & 0x3F) == 0x3E) && (a & 0x1FF);
 271         } else {
 272
 273             return ((a >> 9) & 0x3F) == 0x3F;
 274         }
 275     }
 276 }
 277
 278 /*----------------------------------------------------------------------------
 279 | Returns 1 if the bfloat16 value `a' is a quiet
 280 | NaN; otherwise returns 0.
 281 *----------------------------------------------------------------------------*/
 282
 283 bool bfloat16_is_quiet_nan(bfloat16 a_, float_status *status)
 284 {
 285     if (no_signaling_nans(status)) {
 286         return bfloat16_is_any_nan(a_);
 287     } else {
 288         uint16_t a = a_;
 289         if (snan_bit_is_one(status)) {
 290             return (((a >> 6) & 0x1FF) == 0x1FE) && (a & 0x3F);
 291         } else {
 292             return ((a >> 6) & 0x1FF) == 0x1FF;
 293         }
 294     }
 295 }
 296
 297 /*----------------------------------------------------------------------------
 298 | Returns 1 if the half-precision floating-point value `a' is a signaling
 299 | NaN; otherwise returns 0.
 300 *----------------------------------------------------------------------------*/
 301
 302 bool float16_is_signaling_nan(float16 a_, float_status *status)
 303 {
 304     if (no_signaling_nans(status)) {
 305         return 0;
 306     } else {
 307         uint16_t a = float16_val(a_);
 308         if (snan_bit_is_one(status)) {
 309             return ((a >> 9) & 0x3F) == 0x3F;
 310         } else {
 311             return (((a >> 9) & 0x3F) == 0x3E) && (a & 0x1FF);
 312         }
 313     }
 314 }
 315
 316 /*----------------------------------------------------------------------------
 317 | Returns 1 if the bfloat16 value `a' is a signaling
 318 | NaN; otherwise returns 0.
 319 *----------------------------------------------------------------------------*/
 320
 321 bool bfloat16_is_signaling_nan(bfloat16 a_, float_status *status)
 322 {
 323     if (no_signaling_nans(status)) {
 324         return 0;
 325     } else {
 326         uint16_t a = a_;
 327         if (snan_bit_is_one(status)) {
 328             return ((a >> 6) & 0x1FF) == 0x1FF;
 329         } else {
 330             return (((a >> 6) & 0x1FF) == 0x1FE) && (a & 0x3F);
 331         }
 332     }
 333 }
 334
 335 /*----------------------------------------------------------------------------
 336 | Returns 1 if the single-precision floating-point value `a' is a quiet
 337 | NaN; otherwise returns 0.
 338 *----------------------------------------------------------------------------*/
 339
 340 bool float32_is_quiet_nan(float32 a_, float_status *status)
 341 {
 342     if (no_signaling_nans(status)) {
 343         return float32_is_any_nan(a_);
 344     } else {
 345         uint32_t a = float32_val(a_);
 346         if (snan_bit_is_one(status)) {
 347             return (((a >> 22) & 0x1FF) == 0x1FE) && (a & 0x003FFFFF);
 348         } else {
 349             return ((uint32_t)(a << 1) >= 0xFF800000);
 350         }
 351     }
 352 }
 353
 354 /*----------------------------------------------------------------------------
 355 | Returns 1 if the single-precision floating-point value `a' is a signaling
 356 | NaN; otherwise returns 0.
 357 *----------------------------------------------------------------------------*/
 358
 359 bool float32_is_signaling_nan(float32 a_, float_status *status)
 360 {
 361     if (no_signaling_nans(status)) {
 362         return 0;
 363     } else {
 364         uint32_t a = float32_val(a_);
 365         if (snan_bit_is_one(status)) {
 366             return ((uint32_t)(a << 1) >= 0xFF800000);
 367         } else {
 368             return (((a >> 22) & 0x1FF) == 0x1FE) && (a & 0x003FFFFF);
 369         }
 370     }
 371 }
 372
 373 /*----------------------------------------------------------------------------
 374 | Select which NaN to propagate for a two-input operation.
 375 | IEEE754 doesn't specify all the details of this, so the
 376 | algorithm is target-specific.
 377 | The routine is passed various bits of information about the
 378 | two NaNs and should return 0 to select NaN a and 1 for NaN b.
 379 | Note that signalling NaNs are always squashed to quiet NaNs
 380 | by the caller, by calling floatXX_silence_nan() before
 381 | returning them.
 382 |
 383 | aIsLargerSignificand is only valid if both a and b are NaNs
 384 | of some kind, and is true if a has the larger significand,
 385 | or if both a and b have the same significand but a is
 386 | positive but b is negative. It is only needed for the x87
 387 | tie-break rule.
 388 *----------------------------------------------------------------------------*/
 389
 390 static int pickNaN(FloatClass a_cls, FloatClass b_cls,
 391                    bool aIsLargerSignificand, float_status *status)
 392 {
 393 #if defined(TARGET_ARM) || defined(TARGET_MIPS) || defined(TARGET_HPPA) || \
 394     defined(TARGET_LOONGARCH64) || defined(TARGET_S390X)
 395     /* ARM mandated NaN propagation rules (see FPProcessNaNs()), take
 396      * the first of:
 397      *  1. A if it is signaling
 398      *  2. B if it is signaling
 399      *  3. A (quiet)
 400      *  4. B (quiet)
 401      * A signaling NaN is always quietened before returning it.
 402      */
 403     /* According to MIPS specifications, if one of the two operands is
 404      * a sNaN, a new qNaN has to be generated. This is done in
 405      * floatXX_silence_nan(). For qNaN inputs the specifications
 406      * says: "When possible, this QNaN result is one of the operand QNaN
 407      * values." In practice it seems that most implementations choose
 408      * the first operand if both operands are qNaN. In short this gives
 409      * the following rules:
 410      *  1. A if it is signaling
 411      *  2. B if it is signaling
 412      *  3. A (quiet)
 413      *  4. B (quiet)
 414      * A signaling NaN is always silenced before returning it.
 415      */
 416     if (is_snan(a_cls)) {
 417         return 0;
 418     } else if (is_snan(b_cls)) {
 419         return 1;
 420     } else if (is_qnan(a_cls)) {
 421         return 0;
 422     } else {
 423         return 1;
 424     }
 425 #elif defined(TARGET_PPC) || defined(TARGET_M68K)
 426     /* PowerPC propagation rules:
 427      *  1. A if it sNaN or qNaN
 428      *  2. B if it sNaN or qNaN
 429      * A signaling NaN is always silenced before returning it.
 430      */
 431     /* M68000 FAMILY PROGRAMMER'S REFERENCE MANUAL
 432      * 3.4 FLOATING-POINT INSTRUCTION DETAILS
 433      * If either operand, but not both operands, of an operation is a
 434      * nonsignaling NaN, then that NaN is returned as the result. If both
 435      * operands are nonsignaling NaNs, then the destination operand
 436      * nonsignaling NaN is returned as the result.
 437      * If either operand to an operation is a signaling NaN (SNaN), then the
 438      * SNaN bit is set in the FPSR EXC byte. If the SNaN exception enable bit
 439      * is set in the FPCR ENABLE byte, then the exception is taken and the
 440      * destination is not modified. If the SNaN exception enable bit is not
 441      * set, setting the SNaN bit in the operand to a one converts the SNaN to
 442      * a nonsignaling NaN. The operation then continues as described in the
 443      * preceding paragraph for nonsignaling NaNs.
 444      */
 445     if (is_nan(a_cls)) {
 446         return 0;
 447     } else {
 448         return 1;
 449     }
 450 #elif defined(TARGET_XTENSA)
 451     /*
 452      * Xtensa has two NaN propagation modes.
 453      * Which one is active is controlled by float_status::use_first_nan.
 454      */
 455     if (status->use_first_nan) {
 456         if (is_nan(a_cls)) {
 457             return 0;
 458         } else {
 459             return 1;
 460         }
 461     } else {
 462         if (is_nan(b_cls)) {
 463             return 1;
 464         } else {
 465             return 0;
 466         }
 467     }
 468 #else
 469     /* This implements x87 NaN propagation rules:
 470      * SNaN + QNaN => return the QNaN
 471      * two SNaNs => return the one with the larger significand, silenced
 472      * two QNaNs => return the one with the larger significand
 473      * SNaN and a non-NaN => return the SNaN, silenced
 474      * QNaN and a non-NaN => return the QNaN
 475      *
 476      * If we get down to comparing significands and they are the same,
 477      * return the NaN with the positive sign bit (if any).
 478      */
 479     if (is_snan(a_cls)) {
 480         if (is_snan(b_cls)) {
 481             return aIsLargerSignificand ? 0 : 1;
 482         }
 483         return is_qnan(b_cls) ? 1 : 0;
 484     } else if (is_qnan(a_cls)) {
 485         if (is_snan(b_cls) || !is_qnan(b_cls)) {
 486             return 0;
 487         } else {
 488             return aIsLargerSignificand ? 0 : 1;
 489         }
 490     } else {
 491         return 1;
 492     }
 493 #endif
 494 }
 495
 496 /*----------------------------------------------------------------------------
 497 | Select which NaN to propagate for a three-input operation.
 498 | For the moment we assume that no CPU needs the 'larger significand'
 499 | information.
 500 | Return values : 0 : a; 1 : b; 2 : c; 3 : default-NaN
 501 *----------------------------------------------------------------------------*/
 502 static int pickNaNMulAdd(FloatClass a_cls, FloatClass b_cls, FloatClass c_cls,
 503                          bool infzero, float_status *status)
 504 {
 505 #if defined(TARGET_ARM)
 506     /* For ARM, the (inf,zero,qnan) case sets InvalidOp and returns
 507      * the default NaN
 508      */
 509     if (infzero && is_qnan(c_cls)) {
 510         float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 511         return 3;
 512     }
 513
 514     /* This looks different from the ARM ARM pseudocode, because the ARM ARM
 515      * puts the operands to a fused mac operation (a*b)+c in the order c,a,b.
 516      */
 517     if (is_snan(c_cls)) {
 518         return 2;
 519     } else if (is_snan(a_cls)) {
 520         return 0;
 521     } else if (is_snan(b_cls)) {
 522         return 1;
 523     } else if (is_qnan(c_cls)) {
 524         return 2;
 525     } else if (is_qnan(a_cls)) {
 526         return 0;
 527     } else {
 528         return 1;
 529     }
 530 #elif defined(TARGET_MIPS)
 531     if (snan_bit_is_one(status)) {
 532         /*
 533          * For MIPS systems that conform to IEEE754-1985, the (inf,zero,nan)
 534          * case sets InvalidOp and returns the default NaN
 535          */
 536         if (infzero) {
 537             float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 538             return 3;
 539         }
 540         /* Prefer sNaN over qNaN, in the a, b, c order. */
 541         if (is_snan(a_cls)) {
 542             return 0;
 543         } else if (is_snan(b_cls)) {
 544             return 1;
 545         } else if (is_snan(c_cls)) {
 546             return 2;
 547         } else if (is_qnan(a_cls)) {
 548             return 0;
 549         } else if (is_qnan(b_cls)) {
 550             return 1;
 551         } else {
 552             return 2;
 553         }
 554     } else {
 555         /*
 556          * For MIPS systems that conform to IEEE754-2008, the (inf,zero,nan)
 557          * case sets InvalidOp and returns the input value 'c'
 558          */
 559         if (infzero) {
 560             float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 561             return 2;
 562         }
 563         /* Prefer sNaN over qNaN, in the c, a, b order. */
 564         if (is_snan(c_cls)) {
 565             return 2;
 566         } else if (is_snan(a_cls)) {
 567             return 0;
 568         } else if (is_snan(b_cls)) {
 569             return 1;
 570         } else if (is_qnan(c_cls)) {
 571             return 2;
 572         } else if (is_qnan(a_cls)) {
 573             return 0;
 574         } else {
 575             return 1;
 576         }
 577     }
 578 #elif defined(TARGET_LOONGARCH64)
 579     /*
 580      * For LoongArch systems that conform to IEEE754-2008, the (inf,zero,nan)
 581      * case sets InvalidOp and returns the input value 'c'
 582      */
 583     if (infzero) {
 584         float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 585         return 2;
 586     }
 587     /* Prefer sNaN over qNaN, in the c, a, b order. */
 588     if (is_snan(c_cls)) {
 589         return 2;
 590     } else if (is_snan(a_cls)) {
 591         return 0;
 592     } else if (is_snan(b_cls)) {
 593         return 1;
 594     } else if (is_qnan(c_cls)) {
 595         return 2;
 596     } else if (is_qnan(a_cls)) {
 597         return 0;
 598     } else {
 599         return 1;
 600     }
 601 #elif defined(TARGET_PPC)
 602     /* For PPC, the (inf,zero,qnan) case sets InvalidOp, but we prefer
 603      * to return an input NaN if we have one (ie c) rather than generating
 604      * a default NaN
 605      */
 606     if (infzero) {
 607         float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 608         return 2;
 609     }
 610
 611     /* If fRA is a NaN return it; otherwise if fRB is a NaN return it;
 612      * otherwise return fRC. Note that muladd on PPC is (fRA * fRC) + frB
 613      */
 614     if (is_nan(a_cls)) {
 615         return 0;
 616     } else if (is_nan(c_cls)) {
 617         return 2;
 618     } else {
 619         return 1;
 620     }
 621 #elif defined(TARGET_RISCV)
 622     /* For RISC-V, InvalidOp is set when multiplicands are Inf and zero */
 623     if (infzero) {
 624         float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 625     }
 626     return 3; /* default NaN */
 627 #elif defined(TARGET_XTENSA)
 628     /*
 629      * For Xtensa, the (inf,zero,nan) case sets InvalidOp and returns
 630      * an input NaN if we have one (ie c).
 631      */
 632     if (infzero) {
 633         float_raise(float_flag_invalid | float_flag_invalid_imz, status);
 634         return 2;
 635     }
 636     if (status->use_first_nan) {
 637         if (is_nan(a_cls)) {
 638             return 0;
 639         } else if (is_nan(b_cls)) {
 640             return 1;
 641         } else {
 642             return 2;
 643         }
 644     } else {
 645         if (is_nan(c_cls)) {
 646             return 2;
 647         } else if (is_nan(b_cls)) {
 648             return 1;
 649         } else {
 650             return 0;
 651         }
 652     }
 653 #else
 654     /* A default implementation: prefer a to b to c.
 655      * This is unlikely to actually match any real implementation.
 656      */
 657     if (is_nan(a_cls)) {
 658         return 0;
 659     } else if (is_nan(b_cls)) {
 660         return 1;
 661     } else {
 662         return 2;
 663     }
 664 #endif
 665 }
 666
 667 /*----------------------------------------------------------------------------
 668 | Returns 1 if the double-precision floating-point value `a' is a quiet
 669 | NaN; otherwise returns 0.
 670 *----------------------------------------------------------------------------*/
 671
 672 bool float64_is_quiet_nan(float64 a_, float_status *status)
 673 {
 674     if (no_signaling_nans(status)) {
 675         return float64_is_any_nan(a_);
 676     } else {
 677         uint64_t a = float64_val(a_);
 678         if (snan_bit_is_one(status)) {
 679             return (((a >> 51) & 0xFFF) == 0xFFE)
 680                 && (a & 0x0007FFFFFFFFFFFFULL);
 681         } else {
 682             return ((a << 1) >= 0xFFF0000000000000ULL);
 683         }
 684     }
 685 }
 686
 687 /*----------------------------------------------------------------------------
 688 | Returns 1 if the double-precision floating-point value `a' is a signaling
 689 | NaN; otherwise returns 0.
 690 *----------------------------------------------------------------------------*/
 691
 692 bool float64_is_signaling_nan(float64 a_, float_status *status)
 693 {
 694     if (no_signaling_nans(status)) {
 695         return 0;
 696     } else {
 697         uint64_t a = float64_val(a_);
 698         if (snan_bit_is_one(status)) {
 699             return ((a << 1) >= 0xFFF0000000000000ULL);
 700         } else {
 701             return (((a >> 51) & 0xFFF) == 0xFFE)
 702                 && (a & UINT64_C(0x0007FFFFFFFFFFFF));
 703         }
 704     }
 705 }
 706
 707 /*----------------------------------------------------------------------------
 708 | Returns 1 if the extended double-precision floating-point value `a' is a
 709 | quiet NaN; otherwise returns 0. This slightly differs from the same
 710 | function for other types as floatx80 has an explicit bit.
 711 *----------------------------------------------------------------------------*/
 712
 713 int floatx80_is_quiet_nan(floatx80 a, float_status *status)
 714 {
 715     if (no_signaling_nans(status)) {
 716         return floatx80_is_any_nan(a);
 717     } else {
 718         if (snan_bit_is_one(status)) {
 719             uint64_t aLow;
 720
 721             aLow = a.low & ~0x4000000000000000ULL;
 722             return ((a.high & 0x7FFF) == 0x7FFF)
 723                 && (aLow << 1)
 724                 && (a.low == aLow);
 725         } else {
 726             return ((a.high & 0x7FFF) == 0x7FFF)
 727                 && (UINT64_C(0x8000000000000000) <= ((uint64_t)(a.low << 1)));
 728         }
 729     }
 730 }
 731
 732 /*----------------------------------------------------------------------------
 733 | Returns 1 if the extended double-precision floating-point value `a' is a
 734 | signaling NaN; otherwise returns 0. This slightly differs from the same
 735 | function for other types as floatx80 has an explicit bit.
 736 *----------------------------------------------------------------------------*/
 737
 738 int floatx80_is_signaling_nan(floatx80 a, float_status *status)
 739 {
 740     if (no_signaling_nans(status)) {
 741         return 0;
 742     } else {
 743         if (snan_bit_is_one(status)) {
 744             return ((a.high & 0x7FFF) == 0x7FFF)
 745                 && ((a.low << 1) >= 0x8000000000000000ULL);
 746         } else {
 747             uint64_t aLow;
 748
 749             aLow = a.low & ~UINT64_C(0x4000000000000000);
 750             return ((a.high & 0x7FFF) == 0x7FFF)
 751                 && (uint64_t)(aLow << 1)
 752                 && (a.low == aLow);
 753         }
 754     }
 755 }
 756
 757 /*----------------------------------------------------------------------------
 758 | Returns a quiet NaN from a signalling NaN for the extended double-precision
 759 | floating point value `a'.
 760 *----------------------------------------------------------------------------*/
 761
 762 floatx80 floatx80_silence_nan(floatx80 a, float_status *status)
 763 {
 764     /* None of the targets that have snan_bit_is_one use floatx80.  */
 765     assert(!snan_bit_is_one(status));
 766     a.low |= UINT64_C(0xC000000000000000);
 767     return a;
 768 }
 769
 770 /*----------------------------------------------------------------------------
 771 | Takes two extended double-precision floating-point values `a' and `b', one
 772 | of which is a NaN, and returns the appropriate NaN result.  If either `a' or
 773 | `b' is a signaling NaN, the invalid exception is raised.
 774 *----------------------------------------------------------------------------*/
 775
 776 floatx80 propagateFloatx80NaN(floatx80 a, floatx80 b, float_status *status)
 777 {
 778     bool aIsLargerSignificand;
 779     FloatClass a_cls, b_cls;
 780
 781     /* This is not complete, but is good enough for pickNaN.  */
 782     a_cls = (!floatx80_is_any_nan(a)
 783              ? float_class_normal
 784              : floatx80_is_signaling_nan(a, status)
 785              ? float_class_snan
 786              : float_class_qnan);
 787     b_cls = (!floatx80_is_any_nan(b)
 788              ? float_class_normal
 789              : floatx80_is_signaling_nan(b, status)
 790              ? float_class_snan
 791              : float_class_qnan);
 792
 793     if (is_snan(a_cls) || is_snan(b_cls)) {
 794         float_raise(float_flag_invalid, status);
 795     }
 796
 797     if (status->default_nan_mode) {
 798         return floatx80_default_nan(status);
 799     }
 800
 801     if (a.low < b.low) {
 802         aIsLargerSignificand = 0;
 803     } else if (b.low < a.low) {
 804         aIsLargerSignificand = 1;
 805     } else {
 806         aIsLargerSignificand = (a.high < b.high) ? 1 : 0;
 807     }
 808
 809     if (pickNaN(a_cls, b_cls, aIsLargerSignificand, status)) {
 810         if (is_snan(b_cls)) {
 811             return floatx80_silence_nan(b, status);
 812         }
 813         return b;
 814     } else {
 815         if (is_snan(a_cls)) {
 816             return floatx80_silence_nan(a, status);
 817         }
 818         return a;
 819     }
 820 }
 821
 822 /*----------------------------------------------------------------------------
 823 | Returns 1 if the quadruple-precision floating-point value `a' is a quiet
 824 | NaN; otherwise returns 0.
 825 *----------------------------------------------------------------------------*/
 826
 827 bool float128_is_quiet_nan(float128 a, float_status *status)
 828 {
 829     if (no_signaling_nans(status)) {
 830         return float128_is_any_nan(a);
 831     } else {
 832         if (snan_bit_is_one(status)) {
 833             return (((a.high >> 47) & 0xFFFF) == 0xFFFE)
 834                 && (a.low || (a.high & 0x00007FFFFFFFFFFFULL));
 835         } else {
 836             return ((a.high << 1) >= 0xFFFF000000000000ULL)
 837                 && (a.low || (a.high & 0x0000FFFFFFFFFFFFULL));
 838         }
 839     }
 840 }
 841
 842 /*----------------------------------------------------------------------------
 843 | Returns 1 if the quadruple-precision floating-point value `a' is a
 844 | signaling NaN; otherwise returns 0.
 845 *----------------------------------------------------------------------------*/
 846
 847 bool float128_is_signaling_nan(float128 a, float_status *status)
 848 {
 849     if (no_signaling_nans(status)) {
 850         return 0;
 851     } else {
 852         if (snan_bit_is_one(status)) {
 853             return ((a.high << 1) >= 0xFFFF000000000000ULL)
 854                 && (a.low || (a.high & 0x0000FFFFFFFFFFFFULL));
 855         } else {
 856             return (((a.high >> 47) & 0xFFFF) == 0xFFFE)
 857                 && (a.low || (a.high & UINT64_C(0x00007FFFFFFFFFFF)));
 858         }
 859     }
 860 }