include/linux/ide.h

   1 #ifndef _IDE_H
   2 #define _IDE_H
   3 /*
   4  *  linux/include/linux/ide.h
   5  *
   6  *  Copyright (C) 1994-2002  Linus Torvalds & authors
   7  */
   8
   9 #include <linux/init.h>
  10 #include <linux/ioport.h>
  11 #include <linux/ata.h>
  12 #include <linux/blkdev.h>
  13 #include <linux/proc_fs.h>
  14 #include <linux/interrupt.h>
  15 #include <linux/bitops.h>
  16 #include <linux/bio.h>
  17 #include <linux/device.h>
  18 #include <linux/pci.h>
  19 #include <linux/completion.h>
  20 #include <linux/pm.h>
  21 #ifdef CONFIG_BLK_DEV_IDEACPI
  22 #include <acpi/acpi.h>
  23 #endif
  24 #include <asm/byteorder.h>
  25 #include <asm/system.h>
  26 #include <asm/io.h>
  27 #include <asm/mutex.h>
  28
  29 #if defined(CONFIG_CRIS) || defined(CONFIG_FRV) || defined(CONFIG_MN10300)
  30 # define SUPPORT_VLB_SYNC 0
  31 #else
  32 # define SUPPORT_VLB_SYNC 1
  33 #endif
  34
  35 /*
  36  * Probably not wise to fiddle with these
  37  */
  38 #define IDE_DEFAULT_MAX_FAILURES        1
  39 #define ERROR_MAX       8       /* Max read/write errors per sector */
  40 #define ERROR_RESET     3       /* Reset controller every 4th retry */
  41 #define ERROR_RECAL     1       /* Recalibrate every 2nd retry */
  42
  43 /* Error codes returned in rq->errors to the higher part of the driver. */
  44 enum {
  45         IDE_DRV_ERROR_GENERAL   = 101,
  46         IDE_DRV_ERROR_FILEMARK  = 102,
  47         IDE_DRV_ERROR_EOD       = 103,
  48 };
  49
  50 /*
  51  * Definitions for accessing IDE controller registers
  52  */
  53 #define IDE_NR_PORTS            (10)
  54
  55 struct ide_io_ports {
  56         unsigned long   data_addr;
  57
  58         union {
  59                 unsigned long error_addr;       /*   read:  error */
  60                 unsigned long feature_addr;     /*  write: feature */
  61         };
  62
  63         unsigned long   nsect_addr;
  64         unsigned long   lbal_addr;
  65         unsigned long   lbam_addr;
  66         unsigned long   lbah_addr;
  67
  68         unsigned long   device_addr;
  69
  70         union {
  71                 unsigned long status_addr;      /*  read: status  */
  72                 unsigned long command_addr;     /* write: command */
  73         };
  74
  75         unsigned long   ctl_addr;
  76
  77         unsigned long   irq_addr;
  78 };
  79
  80 #define OK_STAT(stat,good,bad)  (((stat)&((good)|(bad)))==(good))
  81
  82 #define BAD_R_STAT      (ATA_BUSY | ATA_ERR)
  83 #define BAD_W_STAT      (BAD_R_STAT | ATA_DF)
  84 #define BAD_STAT        (BAD_R_STAT | ATA_DRQ)
  85 #define DRIVE_READY     (ATA_DRDY | ATA_DSC)
  86
  87 #define BAD_CRC         (ATA_ABORTED | ATA_ICRC)
  88
  89 #define SATA_NR_PORTS           (3)     /* 16 possible ?? */
  90
  91 #define SATA_STATUS_OFFSET      (0)
  92 #define SATA_ERROR_OFFSET       (1)
  93 #define SATA_CONTROL_OFFSET     (2)
  94
  95 /*
  96  * Our Physical Region Descriptor (PRD) table should be large enough
  97  * to handle the biggest I/O request we are likely to see.  Since requests
  98  * can have no more than 256 sectors, and since the typical blocksize is
  99  * two or more sectors, we could get by with a limit of 128 entries here for
 100  * the usual worst case.  Most requests seem to include some contiguous blocks,
 101  * further reducing the number of table entries required.
 102  *
 103  * The driver reverts to PIO mode for individual requests that exceed
 104  * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
 105  * 100% of all crazy scenarios here is not necessary.
 106  *
 107  * As it turns out though, we must allocate a full 4KB page for this,
 108  * so the two PRD tables (ide0 & ide1) will each get half of that,
 109  * allowing each to have about 256 entries (8 bytes each) from this.
 110  */
 111 #define PRD_BYTES       8
 112 #define PRD_ENTRIES     256
 113
 114 /*
 115  * Some more useful definitions
 116  */
 117 #define PARTN_BITS      6       /* number of minor dev bits for partitions */
 118 #define MAX_DRIVES      2       /* per interface; 2 assumed by lots of code */
 119 #define SECTOR_SIZE     512
 120
 121 /*
 122  * Timeouts for various operations:
 123  */
 124 enum {
 125         /* spec allows up to 20ms */
 126         WAIT_DRQ        = HZ / 10,      /* 100ms */
 127         /* some laptops are very slow */
 128         WAIT_READY      = 5 * HZ,       /* 5s */
 129         /* should be less than 3ms (?), if all ATAPI CD is closed at boot */
 130         WAIT_PIDENTIFY  = 10 * HZ,      /* 10s */
 131         /* worst case when spinning up */
 132         WAIT_WORSTCASE  = 30 * HZ,      /* 30s */
 133         /* maximum wait for an IRQ to happen */
 134         WAIT_CMD        = 10 * HZ,      /* 10s */
 135         /* Some drives require a longer IRQ timeout. */
 136         WAIT_FLOPPY_CMD = 50 * HZ,      /* 50s */
 137         /*
 138          * Some drives (for example, Seagate STT3401A Travan) require a very
 139          * long timeout, because they don't return an interrupt or clear their
 140          * BSY bit until after the command completes (even retension commands).
 141          */
 142         WAIT_TAPE_CMD   = 900 * HZ,     /* 900s */
 143         /* minimum sleep time */
 144         WAIT_MIN_SLEEP  = HZ / 50,      /* 20ms */
 145 };
 146
 147 /*
 148  * Op codes for special requests to be handled by ide_special_rq().
 149  * Values should be in the range of 0x20 to 0x3f.
 150  */
 151 #define REQ_DRIVE_RESET         0x20
 152 #define REQ_DEVSET_EXEC         0x21
 153 #define REQ_PARK_HEADS          0x22
 154 #define REQ_UNPARK_HEADS        0x23
 155
 156 /*
 157  * Check for an interrupt and acknowledge the interrupt status
 158  */
 159 struct hwif_s;
 160 typedef int (ide_ack_intr_t)(struct hwif_s *);
 161
 162 /*
 163  * hwif_chipset_t is used to keep track of the specific hardware
 164  * chipset used by each IDE interface, if known.
 165  */
 166 enum {          ide_unknown,    ide_generic,    ide_pci,
 167                 ide_cmd640,     ide_dtc2278,    ide_ali14xx,
 168                 ide_qd65xx,     ide_umc8672,    ide_ht6560b,
 169                 ide_4drives,    ide_pmac,       ide_acorn,
 170                 ide_au1xxx,     ide_palm3710
 171 };
 172
 173 typedef u8 hwif_chipset_t;
 174
 175 /*
 176  * Structure to hold all information about the location of this port
 177  */
 178 typedef struct hw_regs_s {
 179         union {
 180                 struct ide_io_ports     io_ports;
 181                 unsigned long           io_ports_array[IDE_NR_PORTS];
 182         };
 183
 184         int             irq;                    /* our irq number */
 185         ide_ack_intr_t  *ack_intr;              /* acknowledge interrupt */
 186         hwif_chipset_t  chipset;
 187         struct device   *dev, *parent;
 188         unsigned long   config;
 189 } hw_regs_t;
 190
 191 static inline void ide_std_init_ports(hw_regs_t *hw,
 192                                       unsigned long io_addr,
 193                                       unsigned long ctl_addr)
 194 {
 195         unsigned int i;
 196
 197         for (i = 0; i <= 7; i++)
 198                 hw->io_ports_array[i] = io_addr++;
 199
 200         hw->io_ports.ctl_addr = ctl_addr;
 201 }
 202
 203 #define MAX_HWIFS       10
 204
 205 /*
 206  * Now for the data we need to maintain per-drive:  ide_drive_t
 207  */
 208
 209 #define ide_scsi        0x21
 210 #define ide_disk        0x20
 211 #define ide_optical     0x7
 212 #define ide_cdrom       0x5
 213 #define ide_tape        0x1
 214 #define ide_floppy      0x0
 215
 216 /*
 217  * Special Driver Flags
 218  *
 219  * set_geometry : respecify drive geometry
 220  * recalibrate  : seek to cyl 0
 221  * set_multmode : set multmode count
 222  * reserved     : unused
 223  */
 224 typedef union {
 225         unsigned all                    : 8;
 226         struct {
 227                 unsigned set_geometry   : 1;
 228                 unsigned recalibrate    : 1;
 229                 unsigned set_multmode   : 1;
 230                 unsigned reserved       : 5;
 231         } b;
 232 } special_t;
 233
 234 /*
 235  * Status returned from various ide_ functions
 236  */
 237 typedef enum {
 238         ide_stopped,    /* no drive operation was started */
 239         ide_started,    /* a drive operation was started, handler was set */
 240 } ide_startstop_t;
 241
 242 enum {
 243         IDE_TFLAG_LBA48                 = (1 << 0),
 244         IDE_TFLAG_OUT_HOB_FEATURE       = (1 << 1),
 245         IDE_TFLAG_OUT_HOB_NSECT         = (1 << 2),
 246         IDE_TFLAG_OUT_HOB_LBAL          = (1 << 3),
 247         IDE_TFLAG_OUT_HOB_LBAM          = (1 << 4),
 248         IDE_TFLAG_OUT_HOB_LBAH          = (1 << 5),
 249         IDE_TFLAG_OUT_HOB               = IDE_TFLAG_OUT_HOB_FEATURE |
 250                                           IDE_TFLAG_OUT_HOB_NSECT |
 251                                           IDE_TFLAG_OUT_HOB_LBAL |
 252                                           IDE_TFLAG_OUT_HOB_LBAM |
 253                                           IDE_TFLAG_OUT_HOB_LBAH,
 254         IDE_TFLAG_OUT_FEATURE           = (1 << 6),
 255         IDE_TFLAG_OUT_NSECT             = (1 << 7),
 256         IDE_TFLAG_OUT_LBAL              = (1 << 8),
 257         IDE_TFLAG_OUT_LBAM              = (1 << 9),
 258         IDE_TFLAG_OUT_LBAH              = (1 << 10),
 259         IDE_TFLAG_OUT_TF                = IDE_TFLAG_OUT_FEATURE |
 260                                           IDE_TFLAG_OUT_NSECT |
 261                                           IDE_TFLAG_OUT_LBAL |
 262                                           IDE_TFLAG_OUT_LBAM |
 263                                           IDE_TFLAG_OUT_LBAH,
 264         IDE_TFLAG_OUT_DEVICE            = (1 << 11),
 265         IDE_TFLAG_WRITE                 = (1 << 12),
 266         IDE_TFLAG_CUSTOM_HANDLER        = (1 << 13),
 267         IDE_TFLAG_DMA_PIO_FALLBACK      = (1 << 14),
 268         IDE_TFLAG_IN_HOB_ERROR          = (1 << 15),
 269         IDE_TFLAG_IN_HOB_NSECT          = (1 << 16),
 270         IDE_TFLAG_IN_HOB_LBAL           = (1 << 17),
 271         IDE_TFLAG_IN_HOB_LBAM           = (1 << 18),
 272         IDE_TFLAG_IN_HOB_LBAH           = (1 << 19),
 273         IDE_TFLAG_IN_HOB_LBA            = IDE_TFLAG_IN_HOB_LBAL |
 274                                           IDE_TFLAG_IN_HOB_LBAM |
 275                                           IDE_TFLAG_IN_HOB_LBAH,
 276         IDE_TFLAG_IN_HOB                = IDE_TFLAG_IN_HOB_ERROR |
 277                                           IDE_TFLAG_IN_HOB_NSECT |
 278                                           IDE_TFLAG_IN_HOB_LBA,
 279         IDE_TFLAG_IN_ERROR              = (1 << 20),
 280         IDE_TFLAG_IN_NSECT              = (1 << 21),
 281         IDE_TFLAG_IN_LBAL               = (1 << 22),
 282         IDE_TFLAG_IN_LBAM               = (1 << 23),
 283         IDE_TFLAG_IN_LBAH               = (1 << 24),
 284         IDE_TFLAG_IN_LBA                = IDE_TFLAG_IN_LBAL |
 285                                           IDE_TFLAG_IN_LBAM |
 286                                           IDE_TFLAG_IN_LBAH,
 287         IDE_TFLAG_IN_TF                 = IDE_TFLAG_IN_NSECT |
 288                                           IDE_TFLAG_IN_LBA,
 289         IDE_TFLAG_IN_DEVICE             = (1 << 25),
 290         IDE_TFLAG_HOB                   = IDE_TFLAG_OUT_HOB |
 291                                           IDE_TFLAG_IN_HOB,
 292         IDE_TFLAG_TF                    = IDE_TFLAG_OUT_TF |
 293                                           IDE_TFLAG_IN_TF,
 294         IDE_TFLAG_DEVICE                = IDE_TFLAG_OUT_DEVICE |
 295                                           IDE_TFLAG_IN_DEVICE,
 296         /* force 16-bit I/O operations */
 297         IDE_TFLAG_IO_16BIT              = (1 << 26),
 298         /* struct ide_cmd was allocated using kmalloc() */
 299         IDE_TFLAG_DYN                   = (1 << 27),
 300         IDE_TFLAG_FS                    = (1 << 28),
 301         IDE_TFLAG_MULTI_PIO             = (1 << 29),
 302 };
 303
 304 enum {
 305         IDE_FTFLAG_FLAGGED              = (1 << 0),
 306         IDE_FTFLAG_SET_IN_FLAGS         = (1 << 1),
 307         IDE_FTFLAG_OUT_DATA             = (1 << 2),
 308         IDE_FTFLAG_IN_DATA              = (1 << 3),
 309 };
 310
 311 struct ide_taskfile {
 312         u8      hob_data;       /*  0: high data byte (for TASKFILE IOCTL) */
 313                                 /*  1-5: additional data to support LBA48 */
 314         union {
 315                 u8 hob_error;   /*   read: error */
 316                 u8 hob_feature; /*  write: feature */
 317         };
 318
 319         u8      hob_nsect;
 320         u8      hob_lbal;
 321         u8      hob_lbam;
 322         u8      hob_lbah;
 323
 324         u8      data;           /*  6: low data byte (for TASKFILE IOCTL) */
 325
 326         union {                 /*  7: */
 327                 u8 error;       /*   read:  error */
 328                 u8 feature;     /*  write: feature */
 329         };
 330
 331         u8      nsect;          /*  8: number of sectors */
 332         u8      lbal;           /*  9: LBA low */
 333         u8      lbam;           /* 10: LBA mid */
 334         u8      lbah;           /* 11: LBA high */
 335
 336         u8      device;         /* 12: device select */
 337
 338         union {                 /* 13: */
 339                 u8 status;      /*  read: status  */
 340                 u8 command;     /* write: command */
 341         };
 342 };
 343
 344 struct ide_cmd {
 345         union {
 346                 struct ide_taskfile     tf;
 347                 u8                      tf_array[14];
 348         };
 349         u8                      ftf_flags;      /* for TASKFILE ioctl */
 350         u32                     tf_flags;
 351         int                     protocol;
 352
 353         int                     sg_nents;         /* number of sg entries */
 354         int                     orig_sg_nents;
 355         int                     sg_dma_direction; /* DMA transfer direction */
 356
 357         unsigned int            nbytes;
 358         unsigned int            nleft;
 359         unsigned int            last_xfer_len;
 360
 361         struct scatterlist      *cursg;
 362         unsigned int            cursg_ofs;
 363
 364         struct request          *rq;            /* copy of request */
 365         void                    *special;       /* valid_t generally */
 366 };
 367
 368 /* ATAPI packet command flags */
 369 enum {
 370         /* set when an error is considered normal - no retry (ide-tape) */
 371         PC_FLAG_ABORT                   = (1 << 0),
 372         PC_FLAG_SUPPRESS_ERROR          = (1 << 1),
 373         PC_FLAG_WAIT_FOR_DSC            = (1 << 2),
 374         PC_FLAG_DMA_OK                  = (1 << 3),
 375         PC_FLAG_DMA_IN_PROGRESS         = (1 << 4),
 376         PC_FLAG_DMA_ERROR               = (1 << 5),
 377         PC_FLAG_WRITING                 = (1 << 6),
 378 };
 379
 380 /*
 381  * With each packet command, we allocate a buffer of IDE_PC_BUFFER_SIZE bytes.
 382  * This is used for several packet commands (not for READ/WRITE commands).
 383  */
 384 #define IDE_PC_BUFFER_SIZE      64
 385 #define ATAPI_WAIT_PC           (60 * HZ)
 386
 387 struct ide_atapi_pc {
 388         /* actual packet bytes */
 389         u8 c[12];
 390         /* incremented on each retry */
 391         int retries;
 392         int error;
 393
 394         /* bytes to transfer */
 395         int req_xfer;
 396         /* bytes actually transferred */
 397         int xferred;
 398
 399         /* data buffer */
 400         u8 *buf;
 401         /* current buffer position */
 402         u8 *cur_pos;
 403         int buf_size;
 404         /* missing/available data on the current buffer */
 405         int b_count;
 406
 407         /* the corresponding request */
 408         struct request *rq;
 409
 410         unsigned long flags;
 411
 412         /*
 413          * those are more or less driver-specific and some of them are subject
 414          * to change/removal later.
 415          */
 416         u8 pc_buf[IDE_PC_BUFFER_SIZE];
 417
 418         /* idetape only */
 419         struct idetape_bh *bh;
 420         char *b_data;
 421
 422         unsigned long timeout;
 423 };
 424
 425 struct ide_devset;
 426 struct ide_driver;
 427
 428 #ifdef CONFIG_BLK_DEV_IDEACPI
 429 struct ide_acpi_drive_link;
 430 struct ide_acpi_hwif_link;
 431 #endif
 432
 433 struct ide_drive_s;
 434
 435 struct ide_disk_ops {
 436         int             (*check)(struct ide_drive_s *, const char *);
 437         int             (*get_capacity)(struct ide_drive_s *);
 438         void            (*setup)(struct ide_drive_s *);
 439         void            (*flush)(struct ide_drive_s *);
 440         int             (*init_media)(struct ide_drive_s *, struct gendisk *);
 441         int             (*set_doorlock)(struct ide_drive_s *, struct gendisk *,
 442                                         int);
 443         ide_startstop_t (*do_request)(struct ide_drive_s *, struct request *,
 444                                       sector_t);
 445         int             (*ioctl)(struct ide_drive_s *, struct block_device *,
 446                                  fmode_t, unsigned int, unsigned long);
 447 };
 448
 449 /* ATAPI device flags */
 450 enum {
 451         IDE_AFLAG_DRQ_INTERRUPT         = (1 << 0),
 452
 453         /* ide-cd */
 454         /* Drive cannot eject the disc. */
 455         IDE_AFLAG_NO_EJECT              = (1 << 1),
 456         /* Drive is a pre ATAPI 1.2 drive. */
 457         IDE_AFLAG_PRE_ATAPI12           = (1 << 2),
 458         /* TOC addresses are in BCD. */
 459         IDE_AFLAG_TOCADDR_AS_BCD        = (1 << 3),
 460         /* TOC track numbers are in BCD. */
 461         IDE_AFLAG_TOCTRACKS_AS_BCD      = (1 << 4),
 462         /* Saved TOC information is current. */
 463         IDE_AFLAG_TOC_VALID             = (1 << 6),
 464         /* We think that the drive door is locked. */
 465         IDE_AFLAG_DOOR_LOCKED           = (1 << 7),
 466         /* SET_CD_SPEED command is unsupported. */
 467         IDE_AFLAG_NO_SPEED_SELECT       = (1 << 8),
 468         IDE_AFLAG_VERTOS_300_SSD        = (1 << 9),
 469         IDE_AFLAG_VERTOS_600_ESD        = (1 << 10),
 470         IDE_AFLAG_SANYO_3CD             = (1 << 11),
 471         IDE_AFLAG_FULL_CAPS_PAGE        = (1 << 12),
 472         IDE_AFLAG_PLAY_AUDIO_OK         = (1 << 13),
 473         IDE_AFLAG_LE_SPEED_FIELDS       = (1 << 14),
 474
 475         /* ide-floppy */
 476         /* Avoid commands not supported in Clik drive */
 477         IDE_AFLAG_CLIK_DRIVE            = (1 << 15),
 478         /* Requires BH algorithm for packets */
 479         IDE_AFLAG_ZIP_DRIVE             = (1 << 16),
 480         /* Supports format progress report */
 481         IDE_AFLAG_SRFP                  = (1 << 17),
 482
 483         /* ide-tape */
 484         IDE_AFLAG_IGNORE_DSC            = (1 << 18),
 485         /* 0 When the tape position is unknown */
 486         IDE_AFLAG_ADDRESS_VALID         = (1 << 19),
 487         /* Device already opened */
 488         IDE_AFLAG_BUSY                  = (1 << 20),
 489         /* Attempt to auto-detect the current user block size */
 490         IDE_AFLAG_DETECT_BS             = (1 << 21),
 491         /* Currently on a filemark */
 492         IDE_AFLAG_FILEMARK              = (1 << 22),
 493         /* 0 = no tape is loaded, so we don't rewind after ejecting */
 494         IDE_AFLAG_MEDIUM_PRESENT        = (1 << 23),
 495
 496         IDE_AFLAG_NO_AUTOCLOSE          = (1 << 24),
 497 };
 498
 499 /* device flags */
 500 enum {
 501         /* restore settings after device reset */
 502         IDE_DFLAG_KEEP_SETTINGS         = (1 << 0),
 503         /* device is using DMA for read/write */
 504         IDE_DFLAG_USING_DMA             = (1 << 1),
 505         /* okay to unmask other IRQs */
 506         IDE_DFLAG_UNMASK                = (1 << 2),
 507         /* don't attempt flushes */
 508         IDE_DFLAG_NOFLUSH               = (1 << 3),
 509         /* DSC overlap */
 510         IDE_DFLAG_DSC_OVERLAP           = (1 << 4),
 511         /* give potential excess bandwidth */
 512         IDE_DFLAG_NICE1                 = (1 << 5),
 513         /* device is physically present */
 514         IDE_DFLAG_PRESENT               = (1 << 6),
 515         /* id read from device (synthetic if not set) */
 516         IDE_DFLAG_ID_READ               = (1 << 8),
 517         IDE_DFLAG_NOPROBE               = (1 << 9),
 518         /* need to do check_media_change() */
 519         IDE_DFLAG_REMOVABLE             = (1 << 10),
 520         /* needed for removable devices */
 521         IDE_DFLAG_ATTACH                = (1 << 11),
 522         IDE_DFLAG_FORCED_GEOM           = (1 << 12),
 523         /* disallow setting unmask bit */
 524         IDE_DFLAG_NO_UNMASK             = (1 << 13),
 525         /* disallow enabling 32-bit I/O */
 526         IDE_DFLAG_NO_IO_32BIT           = (1 << 14),
 527         /* for removable only: door lock/unlock works */
 528         IDE_DFLAG_DOORLOCKING           = (1 << 15),
 529         /* disallow DMA */
 530         IDE_DFLAG_NODMA                 = (1 << 16),
 531         /* powermanagment told us not to do anything, so sleep nicely */
 532         IDE_DFLAG_BLOCKED               = (1 << 17),
 533         /* sleeping & sleep field valid */
 534         IDE_DFLAG_SLEEPING              = (1 << 18),
 535         IDE_DFLAG_POST_RESET            = (1 << 19),
 536         IDE_DFLAG_UDMA33_WARNED         = (1 << 20),
 537         IDE_DFLAG_LBA48                 = (1 << 21),
 538         /* status of write cache */
 539         IDE_DFLAG_WCACHE                = (1 << 22),
 540         /* used for ignoring ATA_DF */
 541         IDE_DFLAG_NOWERR                = (1 << 23),
 542         /* retrying in PIO */
 543         IDE_DFLAG_DMA_PIO_RETRY         = (1 << 24),
 544         IDE_DFLAG_LBA                   = (1 << 25),
 545         /* don't unload heads */
 546         IDE_DFLAG_NO_UNLOAD             = (1 << 26),
 547         /* heads unloaded, please don't reset port */
 548         IDE_DFLAG_PARKED                = (1 << 27),
 549         IDE_DFLAG_MEDIA_CHANGED         = (1 << 28),
 550         /* write protect */
 551         IDE_DFLAG_WP                    = (1 << 29),
 552         IDE_DFLAG_FORMAT_IN_PROGRESS    = (1 << 30),
 553 };
 554
 555 struct ide_drive_s {
 556         char            name[4];        /* drive name, such as "hda" */
 557         char            driver_req[10]; /* requests specific driver */
 558
 559         struct request_queue    *queue; /* request queue */
 560
 561         struct request          *rq;    /* current request */
 562         void            *driver_data;   /* extra driver data */
 563         u16                     *id;    /* identification info */
 564 #ifdef CONFIG_IDE_PROC_FS
 565         struct proc_dir_entry *proc;    /* /proc/ide/ directory entry */
 566         const struct ide_proc_devset *settings; /* /proc/ide/ drive settings */
 567 #endif
 568         struct hwif_s           *hwif;  /* actually (ide_hwif_t *) */
 569
 570         const struct ide_disk_ops *disk_ops;
 571
 572         unsigned long dev_flags;
 573
 574         unsigned long sleep;            /* sleep until this time */
 575         unsigned long timeout;          /* max time to wait for irq */
 576
 577         special_t       special;        /* special action flags */
 578
 579         u8      select;                 /* basic drive/head select reg value */
 580         u8      retry_pio;              /* retrying dma capable host in pio */
 581         u8      waiting_for_dma;        /* dma currently in progress */
 582         u8      dma;                    /* atapi dma flag */
 583
 584         u8      quirk_list;     /* considered quirky, set for a specific host */
 585         u8      init_speed;     /* transfer rate set at boot */
 586         u8      current_speed;  /* current transfer rate set */
 587         u8      desired_speed;  /* desired transfer rate set */
 588         u8      dn;             /* now wide spread use */
 589         u8      acoustic;       /* acoustic management */
 590         u8      media;          /* disk, cdrom, tape, floppy, ... */
 591         u8      ready_stat;     /* min status value for drive ready */
 592         u8      mult_count;     /* current multiple sector setting */
 593         u8      mult_req;       /* requested multiple sector setting */
 594         u8      io_32bit;       /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
 595         u8      bad_wstat;      /* used for ignoring ATA_DF */
 596         u8      head;           /* "real" number of heads */
 597         u8      sect;           /* "real" sectors per track */
 598         u8      bios_head;      /* BIOS/fdisk/LILO number of heads */
 599         u8      bios_sect;      /* BIOS/fdisk/LILO sectors per track */
 600
 601         /* delay this long before sending packet command */
 602         u8 pc_delay;
 603
 604         unsigned int    bios_cyl;       /* BIOS/fdisk/LILO number of cyls */
 605         unsigned int    cyl;            /* "real" number of cyls */
 606         unsigned int    drive_data;     /* used by set_pio_mode/dev_select() */
 607         unsigned int    failures;       /* current failure count */
 608         unsigned int    max_failures;   /* maximum allowed failure count */
 609         u64             probed_capacity;/* initial reported media capacity (ide-cd only currently) */
 610
 611         u64             capacity64;     /* total number of sectors */
 612
 613         int             lun;            /* logical unit */
 614         int             crc_count;      /* crc counter to reduce drive speed */
 615
 616         unsigned long   debug_mask;     /* debugging levels switch */
 617
 618 #ifdef CONFIG_BLK_DEV_IDEACPI
 619         struct ide_acpi_drive_link *acpidata;
 620 #endif
 621         struct list_head list;
 622         struct device   gendev;
 623         struct completion gendev_rel_comp;      /* to deal with device release() */
 624
 625         /* current packet command */
 626         struct ide_atapi_pc *pc;
 627
 628         /* last failed packet command */
 629         struct ide_atapi_pc *failed_pc;
 630
 631         /* callback for packet commands */
 632         int  (*pc_callback)(struct ide_drive_s *, int);
 633
 634         void (*pc_update_buffers)(struct ide_drive_s *, struct ide_atapi_pc *);
 635         int  (*pc_io_buffers)(struct ide_drive_s *, struct ide_atapi_pc *,
 636                               unsigned int, int);
 637
 638         ide_startstop_t (*irq_handler)(struct ide_drive_s *);
 639
 640         unsigned long atapi_flags;
 641
 642         struct ide_atapi_pc request_sense_pc;
 643         struct request request_sense_rq;
 644 };
 645
 646 typedef struct ide_drive_s ide_drive_t;
 647
 648 #define to_ide_device(dev)              container_of(dev, ide_drive_t, gendev)
 649
 650 #define to_ide_drv(obj, cont_type)      \
 651         container_of(obj, struct cont_type, dev)
 652
 653 #define ide_drv_g(disk, cont_type)      \
 654         container_of((disk)->private_data, struct cont_type, driver)
 655
 656 struct ide_port_info;
 657
 658 struct ide_tp_ops {
 659         void    (*exec_command)(struct hwif_s *, u8);
 660         u8      (*read_status)(struct hwif_s *);
 661         u8      (*read_altstatus)(struct hwif_s *);
 662         void    (*write_devctl)(struct hwif_s *, u8);
 663
 664         void    (*dev_select)(ide_drive_t *);
 665         void    (*tf_load)(ide_drive_t *, struct ide_cmd *);
 666         void    (*tf_read)(ide_drive_t *, struct ide_cmd *);
 667
 668         void    (*input_data)(ide_drive_t *, struct ide_cmd *,
 669                               void *, unsigned int);
 670         void    (*output_data)(ide_drive_t *, struct ide_cmd *,
 671                                void *, unsigned int);
 672 };
 673
 674 extern const struct ide_tp_ops default_tp_ops;
 675
 676 /**
 677  * struct ide_port_ops - IDE port operations
 678  *
 679  * @init_dev:           host specific initialization of a device
 680  * @set_pio_mode:       routine to program host for PIO mode
 681  * @set_dma_mode:       routine to program host for DMA mode
 682  * @reset_poll:         chipset polling based on hba specifics
 683  * @pre_reset:          chipset specific changes to default for device-hba resets
 684  * @resetproc:          routine to reset controller after a disk reset
 685  * @maskproc:           special host masking for drive selection
 686  * @quirkproc:          check host's drive quirk list
 687  * @clear_irq:          clear IRQ
 688  *
 689  * @mdma_filter:        filter MDMA modes
 690  * @udma_filter:        filter UDMA modes
 691  *
 692  * @cable_detect:       detect cable type
 693  */
 694 struct ide_port_ops {
 695         void    (*init_dev)(ide_drive_t *);
 696         void    (*set_pio_mode)(ide_drive_t *, const u8);
 697         void    (*set_dma_mode)(ide_drive_t *, const u8);
 698         int     (*reset_poll)(ide_drive_t *);
 699         void    (*pre_reset)(ide_drive_t *);
 700         void    (*resetproc)(ide_drive_t *);
 701         void    (*maskproc)(ide_drive_t *, int);
 702         void    (*quirkproc)(ide_drive_t *);
 703         void    (*clear_irq)(ide_drive_t *);
 704
 705         u8      (*mdma_filter)(ide_drive_t *);
 706         u8      (*udma_filter)(ide_drive_t *);
 707
 708         u8      (*cable_detect)(struct hwif_s *);
 709 };
 710
 711 struct ide_dma_ops {
 712         void    (*dma_host_set)(struct ide_drive_s *, int);
 713         int     (*dma_setup)(struct ide_drive_s *, struct ide_cmd *);
 714         void    (*dma_start)(struct ide_drive_s *);
 715         int     (*dma_end)(struct ide_drive_s *);
 716         int     (*dma_test_irq)(struct ide_drive_s *);
 717         void    (*dma_lost_irq)(struct ide_drive_s *);
 718         /* below ones are optional */
 719         int     (*dma_check)(struct ide_drive_s *, struct ide_cmd *);
 720         int     (*dma_timer_expiry)(struct ide_drive_s *);
 721         void    (*dma_clear)(struct ide_drive_s *);
 722         /*
 723          * The following method is optional and only required to be
 724          * implemented for the SFF-8038i compatible controllers.
 725          */
 726         u8      (*dma_sff_read_status)(struct hwif_s *);
 727 };
 728
 729 struct ide_host;
 730
 731 typedef struct hwif_s {
 732         struct hwif_s *mate;            /* other hwif from same PCI chip */
 733         struct proc_dir_entry *proc;    /* /proc/ide/ directory entry */
 734
 735         struct ide_host *host;
 736
 737         char name[6];                   /* name of interface, eg. "ide0" */
 738
 739         struct ide_io_ports     io_ports;
 740
 741         unsigned long   sata_scr[SATA_NR_PORTS];
 742
 743         ide_drive_t     *devices[MAX_DRIVES + 1];
 744
 745         u8 major;       /* our major number */
 746         u8 index;       /* 0 for ide0; 1 for ide1; ... */
 747         u8 channel;     /* for dual-port chips: 0=primary, 1=secondary */
 748
 749         u32 host_flags;
 750
 751         u8 pio_mask;
 752
 753         u8 ultra_mask;
 754         u8 mwdma_mask;
 755         u8 swdma_mask;
 756
 757         u8 cbl;         /* cable type */
 758
 759         hwif_chipset_t chipset; /* sub-module for tuning.. */
 760
 761         struct device *dev;
 762
 763         ide_ack_intr_t *ack_intr;
 764
 765         void (*rw_disk)(ide_drive_t *, struct request *);
 766
 767         const struct ide_tp_ops         *tp_ops;
 768         const struct ide_port_ops       *port_ops;
 769         const struct ide_dma_ops        *dma_ops;
 770
 771         /* dma physical region descriptor table (cpu view) */
 772         unsigned int    *dmatable_cpu;
 773         /* dma physical region descriptor table (dma view) */
 774         dma_addr_t      dmatable_dma;
 775
 776         /* maximum number of PRD table entries */
 777         int prd_max_nents;
 778         /* PRD entry size in bytes */
 779         int prd_ent_size;
 780
 781         /* Scatter-gather list used to build the above */
 782         struct scatterlist *sg_table;
 783         int sg_max_nents;               /* Maximum number of entries in it */
 784
 785         struct ide_cmd cmd;             /* current command */
 786
 787         int             rqsize;         /* max sectors per request */
 788         int             irq;            /* our irq number */
 789
 790         unsigned long   dma_base;       /* base addr for dma ports */
 791
 792         unsigned long   config_data;    /* for use by chipset-specific code */
 793         unsigned long   select_data;    /* for use by chipset-specific code */
 794
 795         unsigned long   extra_base;     /* extra addr for dma ports */
 796         unsigned        extra_ports;    /* number of extra dma ports */
 797
 798         unsigned        present    : 1; /* this interface exists */
 799         unsigned        busy       : 1; /* serializes devices on a port */
 800
 801         struct device           gendev;
 802         struct device           *portdev;
 803
 804         struct completion gendev_rel_comp; /* To deal with device release() */
 805
 806         void            *hwif_data;     /* extra hwif data */
 807
 808 #ifdef CONFIG_BLK_DEV_IDEACPI
 809         struct ide_acpi_hwif_link *acpidata;
 810 #endif
 811
 812         /* IRQ handler, if active */
 813         ide_startstop_t (*handler)(ide_drive_t *);
 814
 815         /* BOOL: polling active & poll_timeout field valid */
 816         unsigned int polling : 1;
 817
 818         /* current drive */
 819         ide_drive_t *cur_dev;
 820
 821         /* current request */
 822         struct request *rq;
 823
 824         /* failsafe timer */
 825         struct timer_list timer;
 826         /* timeout value during long polls */
 827         unsigned long poll_timeout;
 828         /* queried upon timeouts */
 829         int (*expiry)(ide_drive_t *);
 830
 831         int req_gen;
 832         int req_gen_timer;
 833
 834         spinlock_t lock;
 835 } ____cacheline_internodealigned_in_smp ide_hwif_t;
 836
 837 #define MAX_HOST_PORTS 4
 838
 839 struct ide_host {
 840         ide_hwif_t      *ports[MAX_HOST_PORTS + 1];
 841         unsigned int    n_ports;
 842         struct device   *dev[2];
 843
 844         int             (*init_chipset)(struct pci_dev *);
 845
 846         void            (*get_lock)(irq_handler_t, void *);
 847         void            (*release_lock)(void);
 848
 849         irq_handler_t   irq_handler;
 850
 851         unsigned long   host_flags;
 852
 853         int             irq_flags;
 854
 855         void            *host_priv;
 856         ide_hwif_t      *cur_port;      /* for hosts requiring serialization */
 857
 858         /* used for hosts requiring serialization */
 859         volatile unsigned long  host_busy;
 860 };
 861
 862 #define IDE_HOST_BUSY 0
 863
 864 /*
 865  *  internal ide interrupt handler type
 866  */
 867 typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
 868 typedef int (ide_expiry_t)(ide_drive_t *);
 869
 870 /* used by ide-cd, ide-floppy, etc. */
 871 typedef void (xfer_func_t)(ide_drive_t *, struct ide_cmd *, void *, unsigned);
 872
 873 extern struct mutex ide_setting_mtx;
 874
 875 /*
 876  * configurable drive settings
 877  */
 878
 879 #define DS_SYNC (1 << 0)
 880
 881 struct ide_devset {
 882         int             (*get)(ide_drive_t *);
 883         int             (*set)(ide_drive_t *, int);
 884         unsigned int    flags;
 885 };
 886
 887 #define __DEVSET(_flags, _get, _set) { \
 888         .flags  = _flags, \
 889         .get    = _get, \
 890         .set    = _set, \
 891 }
 892
 893 #define ide_devset_get(name, field) \
 894 static int get_##name(ide_drive_t *drive) \
 895 { \
 896         return drive->field; \
 897 }
 898
 899 #define ide_devset_set(name, field) \
 900 static int set_##name(ide_drive_t *drive, int arg) \
 901 { \
 902         drive->field = arg; \
 903         return 0; \
 904 }
 905
 906 #define ide_devset_get_flag(name, flag) \
 907 static int get_##name(ide_drive_t *drive) \
 908 { \
 909         return !!(drive->dev_flags & flag); \
 910 }
 911
 912 #define ide_devset_set_flag(name, flag) \
 913 static int set_##name(ide_drive_t *drive, int arg) \
 914 { \
 915         if (arg) \
 916                 drive->dev_flags |= flag; \
 917         else \
 918                 drive->dev_flags &= ~flag; \
 919         return 0; \
 920 }
 921
 922 #define __IDE_DEVSET(_name, _flags, _get, _set) \
 923 const struct ide_devset ide_devset_##_name = \
 924         __DEVSET(_flags, _get, _set)
 925
 926 #define IDE_DEVSET(_name, _flags, _get, _set) \
 927 static __IDE_DEVSET(_name, _flags, _get, _set)
 928
 929 #define ide_devset_rw(_name, _func) \
 930 IDE_DEVSET(_name, 0, get_##_func, set_##_func)
 931
 932 #define ide_devset_w(_name, _func) \
 933 IDE_DEVSET(_name, 0, NULL, set_##_func)
 934
 935 #define ide_ext_devset_rw(_name, _func) \
 936 __IDE_DEVSET(_name, 0, get_##_func, set_##_func)
 937
 938 #define ide_ext_devset_rw_sync(_name, _func) \
 939 __IDE_DEVSET(_name, DS_SYNC, get_##_func, set_##_func)
 940
 941 #define ide_decl_devset(_name) \
 942 extern const struct ide_devset ide_devset_##_name
 943
 944 ide_decl_devset(io_32bit);
 945 ide_decl_devset(keepsettings);
 946 ide_decl_devset(pio_mode);
 947 ide_decl_devset(unmaskirq);
 948 ide_decl_devset(using_dma);
 949
 950 #ifdef CONFIG_IDE_PROC_FS
 951 /*
 952  * /proc/ide interface
 953  */
 954
 955 #define ide_devset_rw_field(_name, _field) \
 956 ide_devset_get(_name, _field); \
 957 ide_devset_set(_name, _field); \
 958 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
 959
 960 #define ide_devset_rw_flag(_name, _field) \
 961 ide_devset_get_flag(_name, _field); \
 962 ide_devset_set_flag(_name, _field); \
 963 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
 964
 965 struct ide_proc_devset {
 966         const char              *name;
 967         const struct ide_devset *setting;
 968         int                     min, max;
 969         int                     (*mulf)(ide_drive_t *);
 970         int                     (*divf)(ide_drive_t *);
 971 };
 972
 973 #define __IDE_PROC_DEVSET(_name, _min, _max, _mulf, _divf) { \
 974         .name = __stringify(_name), \
 975         .setting = &ide_devset_##_name, \
 976         .min = _min, \
 977         .max = _max, \
 978         .mulf = _mulf, \
 979         .divf = _divf, \
 980 }
 981
 982 #define IDE_PROC_DEVSET(_name, _min, _max) \
 983 __IDE_PROC_DEVSET(_name, _min, _max, NULL, NULL)
 984
 985 typedef struct {
 986         const char      *name;
 987         mode_t          mode;
 988         read_proc_t     *read_proc;
 989         write_proc_t    *write_proc;
 990 } ide_proc_entry_t;
 991
 992 void proc_ide_create(void);
 993 void proc_ide_destroy(void);
 994 void ide_proc_register_port(ide_hwif_t *);
 995 void ide_proc_port_register_devices(ide_hwif_t *);
 996 void ide_proc_unregister_device(ide_drive_t *);
 997 void ide_proc_unregister_port(ide_hwif_t *);
 998 void ide_proc_register_driver(ide_drive_t *, struct ide_driver *);
 999 void ide_proc_unregister_driver(ide_drive_t *, struct ide_driver *);
1000
1001 read_proc_t proc_ide_read_capacity;
1002 read_proc_t proc_ide_read_geometry;
1003
1004 /*
1005  * Standard exit stuff:
1006  */
1007 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
1008 {                                       \
1009         len -= off;                     \
1010         if (len < count) {              \
1011                 *eof = 1;               \
1012                 if (len <= 0)           \
1013                         return 0;       \
1014         } else                          \
1015                 len = count;            \
1016         *start = page + off;            \
1017         return len;                     \
1018 }
1019 #else
1020 static inline void proc_ide_create(void) { ; }
1021 static inline void proc_ide_destroy(void) { ; }
1022 static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
1023 static inline void ide_proc_port_register_devices(ide_hwif_t *hwif) { ; }
1024 static inline void ide_proc_unregister_device(ide_drive_t *drive) { ; }
1025 static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
1026 static inline void ide_proc_register_driver(ide_drive_t *drive,
1027                                             struct ide_driver *driver) { ; }
1028 static inline void ide_proc_unregister_driver(ide_drive_t *drive,
1029                                               struct ide_driver *driver) { ; }
1030 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
1031 #endif
1032
1033 enum {
1034         /* enter/exit functions */
1035         IDE_DBG_FUNC =                  (1 << 0),
1036         /* sense key/asc handling */
1037         IDE_DBG_SENSE =                 (1 << 1),
1038         /* packet commands handling */
1039         IDE_DBG_PC =                    (1 << 2),
1040         /* request handling */
1041         IDE_DBG_RQ =                    (1 << 3),
1042         /* driver probing/setup */
1043         IDE_DBG_PROBE =                 (1 << 4),
1044 };
1045
1046 /* DRV_NAME has to be defined in the driver before using the macro below */
1047 #define __ide_debug_log(lvl, fmt, args...)                              \
1048 {                                                                       \
1049         if (unlikely(drive->debug_mask & lvl))                          \
1050                 printk(KERN_INFO DRV_NAME ": %s: " fmt "\n",            \
1051                                           __func__, ## args);           \
1052 }
1053
1054 /*
1055  * Power Management state machine (rq->pm->pm_step).
1056  *
1057  * For each step, the core calls ide_start_power_step() first.
1058  * This can return:
1059  *      - ide_stopped : In this case, the core calls us back again unless
1060  *                      step have been set to ide_power_state_completed.
1061  *      - ide_started : In this case, the channel is left busy until an
1062  *                      async event (interrupt) occurs.
1063  * Typically, ide_start_power_step() will issue a taskfile request with
1064  * do_rw_taskfile().
1065  *
1066  * Upon reception of the interrupt, the core will call ide_complete_power_step()
1067  * with the error code if any. This routine should update the step value
1068  * and return. It should not start a new request. The core will call
1069  * ide_start_power_step() for the new step value, unless step have been
1070  * set to IDE_PM_COMPLETED.
1071  */
1072 enum {
1073         IDE_PM_START_SUSPEND,
1074         IDE_PM_FLUSH_CACHE      = IDE_PM_START_SUSPEND,
1075         IDE_PM_STANDBY,
1076
1077         IDE_PM_START_RESUME,
1078         IDE_PM_RESTORE_PIO      = IDE_PM_START_RESUME,
1079         IDE_PM_IDLE,
1080         IDE_PM_RESTORE_DMA,
1081
1082         IDE_PM_COMPLETED,
1083 };
1084
1085 int generic_ide_suspend(struct device *, pm_message_t);
1086 int generic_ide_resume(struct device *);
1087
1088 void ide_complete_power_step(ide_drive_t *, struct request *);
1089 ide_startstop_t ide_start_power_step(ide_drive_t *, struct request *);
1090 void ide_complete_pm_rq(ide_drive_t *, struct request *);
1091 void ide_check_pm_state(ide_drive_t *, struct request *);
1092
1093 /*
1094  * Subdrivers support.
1095  *
1096  * The gendriver.owner field should be set to the module owner of this driver.
1097  * The gendriver.name field should be set to the name of this driver
1098  */
1099 struct ide_driver {
1100         const char                      *version;
1101         ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
1102         struct device_driver    gen_driver;
1103         int             (*probe)(ide_drive_t *);
1104         void            (*remove)(ide_drive_t *);
1105         void            (*resume)(ide_drive_t *);
1106         void            (*shutdown)(ide_drive_t *);
1107 #ifdef CONFIG_IDE_PROC_FS
1108         ide_proc_entry_t *              (*proc_entries)(ide_drive_t *);
1109         const struct ide_proc_devset *  (*proc_devsets)(ide_drive_t *);
1110 #endif
1111 };
1112
1113 #define to_ide_driver(drv) container_of(drv, struct ide_driver, gen_driver)
1114
1115 int ide_device_get(ide_drive_t *);
1116 void ide_device_put(ide_drive_t *);
1117
1118 struct ide_ioctl_devset {
1119         unsigned int    get_ioctl;
1120         unsigned int    set_ioctl;
1121         const struct ide_devset *setting;
1122 };
1123
1124 int ide_setting_ioctl(ide_drive_t *, struct block_device *, unsigned int,
1125                       unsigned long, const struct ide_ioctl_devset *);
1126
1127 int generic_ide_ioctl(ide_drive_t *, struct block_device *, unsigned, unsigned long);
1128
1129 extern int ide_vlb_clk;
1130 extern int ide_pci_clk;
1131
1132 unsigned int ide_rq_bytes(struct request *);
1133 int ide_end_rq(ide_drive_t *, struct request *, int, unsigned int);
1134 void ide_kill_rq(ide_drive_t *, struct request *);
1135
1136 void __ide_set_handler(ide_drive_t *, ide_handler_t *, unsigned int);
1137 void ide_set_handler(ide_drive_t *, ide_handler_t *, unsigned int);
1138
1139 void ide_execute_command(ide_drive_t *, struct ide_cmd *, ide_handler_t *,
1140                          unsigned int);
1141
1142 void ide_pad_transfer(ide_drive_t *, int, int);
1143
1144 ide_startstop_t ide_error(ide_drive_t *, const char *, u8);
1145
1146 void ide_fix_driveid(u16 *);
1147
1148 extern void ide_fixstring(u8 *, const int, const int);
1149
1150 int ide_busy_sleep(ide_hwif_t *, unsigned long, int);
1151
1152 int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
1153
1154 ide_startstop_t ide_do_park_unpark(ide_drive_t *, struct request *);
1155 ide_startstop_t ide_do_devset(ide_drive_t *, struct request *);
1156
1157 extern ide_startstop_t ide_do_reset (ide_drive_t *);
1158
1159 extern int ide_devset_execute(ide_drive_t *drive,
1160                               const struct ide_devset *setting, int arg);
1161
1162 void ide_complete_cmd(ide_drive_t *, struct ide_cmd *, u8, u8);
1163 int ide_complete_rq(ide_drive_t *, int, unsigned int);
1164
1165 void ide_tf_dump(const char *, struct ide_taskfile *);
1166
1167 void ide_exec_command(ide_hwif_t *, u8);
1168 u8 ide_read_status(ide_hwif_t *);
1169 u8 ide_read_altstatus(ide_hwif_t *);
1170 void ide_write_devctl(ide_hwif_t *, u8);
1171
1172 void ide_dev_select(ide_drive_t *);
1173 void ide_tf_load(ide_drive_t *, struct ide_cmd *);
1174 void ide_tf_read(ide_drive_t *, struct ide_cmd *);
1175
1176 void ide_input_data(ide_drive_t *, struct ide_cmd *, void *, unsigned int);
1177 void ide_output_data(ide_drive_t *, struct ide_cmd *, void *, unsigned int);
1178
1179 void SELECT_MASK(ide_drive_t *, int);
1180
1181 u8 ide_read_error(ide_drive_t *);
1182 void ide_read_bcount_and_ireason(ide_drive_t *, u16 *, u8 *);
1183
1184 int ide_check_atapi_device(ide_drive_t *, const char *);
1185
1186 void ide_init_pc(struct ide_atapi_pc *);
1187
1188 /* Disk head parking */
1189 extern wait_queue_head_t ide_park_wq;
1190 ssize_t ide_park_show(struct device *dev, struct device_attribute *attr,
1191                       char *buf);
1192 ssize_t ide_park_store(struct device *dev, struct device_attribute *attr,
1193                        const char *buf, size_t len);
1194
1195 /*
1196  * Special requests for ide-tape block device strategy routine.
1197  *
1198  * In order to service a character device command, we add special requests to
1199  * the tail of our block device request queue and wait for their completion.
1200  */
1201 enum {
1202         REQ_IDETAPE_PC1         = (1 << 0), /* packet command (first stage) */
1203         REQ_IDETAPE_PC2         = (1 << 1), /* packet command (second stage) */
1204         REQ_IDETAPE_READ        = (1 << 2),
1205         REQ_IDETAPE_WRITE       = (1 << 3),
1206 };
1207
1208 int ide_queue_pc_tail(ide_drive_t *, struct gendisk *, struct ide_atapi_pc *);
1209
1210 int ide_do_test_unit_ready(ide_drive_t *, struct gendisk *);
1211 int ide_do_start_stop(ide_drive_t *, struct gendisk *, int);
1212 int ide_set_media_lock(ide_drive_t *, struct gendisk *, int);
1213 void ide_create_request_sense_cmd(ide_drive_t *, struct ide_atapi_pc *);
1214 void ide_retry_pc(ide_drive_t *, struct gendisk *);
1215
1216 int ide_cd_expiry(ide_drive_t *);
1217
1218 int ide_cd_get_xferlen(struct request *);
1219
1220 ide_startstop_t ide_issue_pc(ide_drive_t *, struct ide_cmd *);
1221
1222 ide_startstop_t do_rw_taskfile(ide_drive_t *, struct ide_cmd *);
1223
1224 void ide_pio_bytes(ide_drive_t *, struct ide_cmd *, unsigned int, unsigned int);
1225
1226 void ide_finish_cmd(ide_drive_t *, struct ide_cmd *, u8);
1227
1228 int ide_raw_taskfile(ide_drive_t *, struct ide_cmd *, u8 *, u16);
1229 int ide_no_data_taskfile(ide_drive_t *, struct ide_cmd *);
1230
1231 int ide_taskfile_ioctl(ide_drive_t *, unsigned long);
1232
1233 int ide_dev_read_id(ide_drive_t *, u8, u16 *);
1234
1235 extern int ide_driveid_update(ide_drive_t *);
1236 extern int ide_config_drive_speed(ide_drive_t *, u8);
1237 extern u8 eighty_ninty_three (ide_drive_t *);
1238 extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
1239
1240 extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);
1241
1242 extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
1243
1244 extern void ide_timer_expiry(unsigned long);
1245 extern irqreturn_t ide_intr(int irq, void *dev_id);
1246 extern void do_ide_request(struct request_queue *);
1247
1248 void ide_init_disk(struct gendisk *, ide_drive_t *);
1249
1250 #ifdef CONFIG_IDEPCI_PCIBUS_ORDER
1251 extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
1252 #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
1253 #else
1254 #define ide_pci_register_driver(d) pci_register_driver(d)
1255 #endif
1256
1257 static inline int ide_pci_is_in_compatibility_mode(struct pci_dev *dev)
1258 {
1259         if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && (dev->class & 5) != 5)
1260                 return 1;
1261         return 0;
1262 }
1263
1264 void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *,
1265                          hw_regs_t *, hw_regs_t **);
1266 void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
1267
1268 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
1269 int ide_pci_set_master(struct pci_dev *, const char *);
1270 unsigned long ide_pci_dma_base(ide_hwif_t *, const struct ide_port_info *);
1271 int ide_pci_check_simplex(ide_hwif_t *, const struct ide_port_info *);
1272 int ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
1273 #else
1274 static inline int ide_hwif_setup_dma(ide_hwif_t *hwif,
1275                                      const struct ide_port_info *d)
1276 {
1277         return -EINVAL;
1278 }
1279 #endif
1280
1281 struct ide_pci_enablebit {
1282         u8      reg;    /* byte pci reg holding the enable-bit */
1283         u8      mask;   /* mask to isolate the enable-bit */
1284         u8      val;    /* value of masked reg when "enabled" */
1285 };
1286
1287 enum {
1288         /* Uses ISA control ports not PCI ones. */
1289         IDE_HFLAG_ISA_PORTS             = (1 << 0),
1290         /* single port device */
1291         IDE_HFLAG_SINGLE                = (1 << 1),
1292         /* don't use legacy PIO blacklist */
1293         IDE_HFLAG_PIO_NO_BLACKLIST      = (1 << 2),
1294         /* set for the second port of QD65xx */
1295         IDE_HFLAG_QD_2ND_PORT           = (1 << 3),
1296         /* use PIO8/9 for prefetch off/on */
1297         IDE_HFLAG_ABUSE_PREFETCH        = (1 << 4),
1298         /* use PIO6/7 for fast-devsel off/on */
1299         IDE_HFLAG_ABUSE_FAST_DEVSEL     = (1 << 5),
1300         /* use 100-102 and 200-202 PIO values to set DMA modes */
1301         IDE_HFLAG_ABUSE_DMA_MODES       = (1 << 6),
1302         /*
1303          * keep DMA setting when programming PIO mode, may be used only
1304          * for hosts which have separate PIO and DMA timings (ie. PMAC)
1305          */
1306         IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
1307         /* program host for the transfer mode after programming device */
1308         IDE_HFLAG_POST_SET_MODE         = (1 << 8),
1309         /* don't program host/device for the transfer mode ("smart" hosts) */
1310         IDE_HFLAG_NO_SET_MODE           = (1 << 9),
1311         /* trust BIOS for programming chipset/device for DMA */
1312         IDE_HFLAG_TRUST_BIOS_FOR_DMA    = (1 << 10),
1313         /* host is CS5510/CS5520 */
1314         IDE_HFLAG_CS5520                = (1 << 11),
1315         /* ATAPI DMA is unsupported */
1316         IDE_HFLAG_NO_ATAPI_DMA          = (1 << 12),
1317         /* set if host is a "non-bootable" controller */
1318         IDE_HFLAG_NON_BOOTABLE          = (1 << 13),
1319         /* host doesn't support DMA */
1320         IDE_HFLAG_NO_DMA                = (1 << 14),
1321         /* check if host is PCI IDE device before allowing DMA */
1322         IDE_HFLAG_NO_AUTODMA            = (1 << 15),
1323         /* host uses MMIO */
1324         IDE_HFLAG_MMIO                  = (1 << 16),
1325         /* no LBA48 */
1326         IDE_HFLAG_NO_LBA48              = (1 << 17),
1327         /* no LBA48 DMA */
1328         IDE_HFLAG_NO_LBA48_DMA          = (1 << 18),
1329         /* data FIFO is cleared by an error */
1330         IDE_HFLAG_ERROR_STOPS_FIFO      = (1 << 19),
1331         /* serialize ports */
1332         IDE_HFLAG_SERIALIZE             = (1 << 20),
1333         /* host is DTC2278 */
1334         IDE_HFLAG_DTC2278               = (1 << 21),
1335         /* 4 devices on a single set of I/O ports */
1336         IDE_HFLAG_4DRIVES               = (1 << 22),
1337         /* host is TRM290 */
1338         IDE_HFLAG_TRM290                = (1 << 23),
1339         /* use 32-bit I/O ops */
1340         IDE_HFLAG_IO_32BIT              = (1 << 24),
1341         /* unmask IRQs */
1342         IDE_HFLAG_UNMASK_IRQS           = (1 << 25),
1343         IDE_HFLAG_BROKEN_ALTSTATUS      = (1 << 26),
1344         /* serialize ports if DMA is possible (for sl82c105) */
1345         IDE_HFLAG_SERIALIZE_DMA         = (1 << 27),
1346         /* force host out of "simplex" mode */
1347         IDE_HFLAG_CLEAR_SIMPLEX         = (1 << 28),
1348         /* DSC overlap is unsupported */
1349         IDE_HFLAG_NO_DSC                = (1 << 29),
1350         /* never use 32-bit I/O ops */
1351         IDE_HFLAG_NO_IO_32BIT           = (1 << 30),
1352         /* never unmask IRQs */
1353         IDE_HFLAG_NO_UNMASK_IRQS        = (1 << 31),
1354 };
1355
1356 #ifdef CONFIG_BLK_DEV_OFFBOARD
1357 # define IDE_HFLAG_OFF_BOARD    0
1358 #else
1359 # define IDE_HFLAG_OFF_BOARD    IDE_HFLAG_NON_BOOTABLE
1360 #endif
1361
1362 struct ide_port_info {
1363         char                    *name;
1364
1365         int                     (*init_chipset)(struct pci_dev *);
1366
1367         void                    (*get_lock)(irq_handler_t, void *);
1368         void                    (*release_lock)(void);
1369
1370         void                    (*init_iops)(ide_hwif_t *);
1371         void                    (*init_hwif)(ide_hwif_t *);
1372         int                     (*init_dma)(ide_hwif_t *,
1373                                             const struct ide_port_info *);
1374
1375         const struct ide_tp_ops         *tp_ops;
1376         const struct ide_port_ops       *port_ops;
1377         const struct ide_dma_ops        *dma_ops;
1378
1379         struct ide_pci_enablebit        enablebits[2];
1380
1381         hwif_chipset_t          chipset;
1382
1383         u16                     max_sectors;    /* if < than the default one */
1384
1385         u32                     host_flags;
1386
1387         int                     irq_flags;
1388
1389         u8                      pio_mask;
1390         u8                      swdma_mask;
1391         u8                      mwdma_mask;
1392         u8                      udma_mask;
1393 };
1394
1395 int ide_pci_init_one(struct pci_dev *, const struct ide_port_info *, void *);
1396 int ide_pci_init_two(struct pci_dev *, struct pci_dev *,
1397                      const struct ide_port_info *, void *);
1398 void ide_pci_remove(struct pci_dev *);
1399
1400 #ifdef CONFIG_PM
1401 int ide_pci_suspend(struct pci_dev *, pm_message_t);
1402 int ide_pci_resume(struct pci_dev *);
1403 #else
1404 #define ide_pci_suspend NULL
1405 #define ide_pci_resume NULL
1406 #endif
1407
1408 void ide_map_sg(ide_drive_t *, struct ide_cmd *);
1409 void ide_init_sg_cmd(struct ide_cmd *, unsigned int);
1410
1411 #define BAD_DMA_DRIVE           0
1412 #define GOOD_DMA_DRIVE          1
1413
1414 struct drive_list_entry {
1415         const char *id_model;
1416         const char *id_firmware;
1417 };
1418
1419 int ide_in_drive_list(u16 *, const struct drive_list_entry *);
1420
1421 #ifdef CONFIG_BLK_DEV_IDEDMA
1422 int ide_dma_good_drive(ide_drive_t *);
1423 int __ide_dma_bad_drive(ide_drive_t *);
1424 int ide_id_dma_bug(ide_drive_t *);
1425
1426 u8 ide_find_dma_mode(ide_drive_t *, u8);
1427
1428 static inline u8 ide_max_dma_mode(ide_drive_t *drive)
1429 {
1430         return ide_find_dma_mode(drive, XFER_UDMA_6);
1431 }
1432
1433 void ide_dma_off_quietly(ide_drive_t *);
1434 void ide_dma_off(ide_drive_t *);
1435 void ide_dma_on(ide_drive_t *);
1436 int ide_set_dma(ide_drive_t *);
1437 void ide_check_dma_crc(ide_drive_t *);
1438 ide_startstop_t ide_dma_intr(ide_drive_t *);
1439
1440 int ide_allocate_dma_engine(ide_hwif_t *);
1441 void ide_release_dma_engine(ide_hwif_t *);
1442
1443 int ide_dma_prepare(ide_drive_t *, struct ide_cmd *);
1444 void ide_dma_unmap_sg(ide_drive_t *, struct ide_cmd *);
1445
1446 #ifdef CONFIG_BLK_DEV_IDEDMA_SFF
1447 int config_drive_for_dma(ide_drive_t *);
1448 int ide_build_dmatable(ide_drive_t *, struct ide_cmd *);
1449 void ide_dma_host_set(ide_drive_t *, int);
1450 int ide_dma_setup(ide_drive_t *, struct ide_cmd *);
1451 extern void ide_dma_start(ide_drive_t *);
1452 int ide_dma_end(ide_drive_t *);
1453 int ide_dma_test_irq(ide_drive_t *);
1454 int ide_dma_sff_timer_expiry(ide_drive_t *);
1455 u8 ide_dma_sff_read_status(ide_hwif_t *);
1456 extern const struct ide_dma_ops sff_dma_ops;
1457 #else
1458 static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; }
1459 #endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
1460
1461 void ide_dma_lost_irq(ide_drive_t *);
1462 ide_startstop_t ide_dma_timeout_retry(ide_drive_t *, int);
1463
1464 #else
1465 static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
1466 static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
1467 static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
1468 static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
1469 static inline void ide_dma_off(ide_drive_t *drive) { ; }
1470 static inline void ide_dma_on(ide_drive_t *drive) { ; }
1471 static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
1472 static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
1473 static inline void ide_check_dma_crc(ide_drive_t *drive) { ; }
1474 static inline ide_startstop_t ide_dma_intr(ide_drive_t *drive) { return ide_stopped; }
1475 static inline ide_startstop_t ide_dma_timeout_retry(ide_drive_t *drive, int error) { return ide_stopped; }
1476 static inline void ide_release_dma_engine(ide_hwif_t *hwif) { ; }
1477 static inline int ide_dma_prepare(ide_drive_t *drive,
1478                                   struct ide_cmd *cmd) { return 1; }
1479 static inline void ide_dma_unmap_sg(ide_drive_t *drive,
1480                                     struct ide_cmd *cmd) { ; }
1481 #endif /* CONFIG_BLK_DEV_IDEDMA */
1482
1483 #ifdef CONFIG_BLK_DEV_IDEACPI
1484 int ide_acpi_init(void);
1485 extern int ide_acpi_exec_tfs(ide_drive_t *drive);
1486 extern void ide_acpi_get_timing(ide_hwif_t *hwif);
1487 extern void ide_acpi_push_timing(ide_hwif_t *hwif);
1488 void ide_acpi_init_port(ide_hwif_t *);
1489 void ide_acpi_port_init_devices(ide_hwif_t *);
1490 extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
1491 #else
1492 static inline int ide_acpi_init(void) { return 0; }
1493 static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
1494 static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
1495 static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
1496 static inline void ide_acpi_init_port(ide_hwif_t *hwif) { ; }
1497 static inline void ide_acpi_port_init_devices(ide_hwif_t *hwif) { ; }
1498 static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
1499 #endif
1500
1501 void ide_register_region(struct gendisk *);
1502 void ide_unregister_region(struct gendisk *);
1503
1504 void ide_undecoded_slave(ide_drive_t *);
1505
1506 void ide_port_apply_params(ide_hwif_t *);
1507 int ide_sysfs_register_port(ide_hwif_t *);
1508
1509 struct ide_host *ide_host_alloc(const struct ide_port_info *, hw_regs_t **);
1510 void ide_host_free(struct ide_host *);
1511 int ide_host_register(struct ide_host *, const struct ide_port_info *,
1512                       hw_regs_t **);
1513 int ide_host_add(const struct ide_port_info *, hw_regs_t **,
1514                  struct ide_host **);
1515 void ide_host_remove(struct ide_host *);
1516 int ide_legacy_device_add(const struct ide_port_info *, unsigned long);
1517 void ide_port_unregister_devices(ide_hwif_t *);
1518 void ide_port_scan(ide_hwif_t *);
1519
1520 static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
1521 {
1522         return hwif->hwif_data;
1523 }
1524
1525 static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
1526 {
1527         hwif->hwif_data = data;
1528 }
1529
1530 extern void ide_toggle_bounce(ide_drive_t *drive, int on);
1531
1532 u64 ide_get_lba_addr(struct ide_taskfile *, int);
1533 u8 ide_dump_status(ide_drive_t *, const char *, u8);
1534
1535 struct ide_timing {
1536         u8  mode;
1537         u8  setup;      /* t1 */
1538         u16 act8b;      /* t2 for 8-bit io */
1539         u16 rec8b;      /* t2i for 8-bit io */
1540         u16 cyc8b;      /* t0 for 8-bit io */
1541         u16 active;     /* t2 or tD */
1542         u16 recover;    /* t2i or tK */
1543         u16 cycle;      /* t0 */
1544         u16 udma;       /* t2CYCTYP/2 */
1545 };
1546
1547 enum {
1548         IDE_TIMING_SETUP        = (1 << 0),
1549         IDE_TIMING_ACT8B        = (1 << 1),
1550         IDE_TIMING_REC8B        = (1 << 2),
1551         IDE_TIMING_CYC8B        = (1 << 3),
1552         IDE_TIMING_8BIT         = IDE_TIMING_ACT8B | IDE_TIMING_REC8B |
1553                                   IDE_TIMING_CYC8B,
1554         IDE_TIMING_ACTIVE       = (1 << 4),
1555         IDE_TIMING_RECOVER      = (1 << 5),
1556         IDE_TIMING_CYCLE        = (1 << 6),
1557         IDE_TIMING_UDMA         = (1 << 7),
1558         IDE_TIMING_ALL          = IDE_TIMING_SETUP | IDE_TIMING_8BIT |
1559                                   IDE_TIMING_ACTIVE | IDE_TIMING_RECOVER |
1560                                   IDE_TIMING_CYCLE | IDE_TIMING_UDMA,
1561 };
1562
1563 struct ide_timing *ide_timing_find_mode(u8);
1564 u16 ide_pio_cycle_time(ide_drive_t *, u8);
1565 void ide_timing_merge(struct ide_timing *, struct ide_timing *,
1566                       struct ide_timing *, unsigned int);
1567 int ide_timing_compute(ide_drive_t *, u8, struct ide_timing *, int, int);
1568
1569 #ifdef CONFIG_IDE_XFER_MODE
1570 int ide_scan_pio_blacklist(char *);
1571 const char *ide_xfer_verbose(u8);
1572 u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
1573 int ide_set_pio_mode(ide_drive_t *, u8);
1574 int ide_set_dma_mode(ide_drive_t *, u8);
1575 void ide_set_pio(ide_drive_t *, u8);
1576 int ide_set_xfer_rate(ide_drive_t *, u8);
1577 #else
1578 static inline void ide_set_pio(ide_drive_t *drive, u8 pio) { ; }
1579 static inline int ide_set_xfer_rate(ide_drive_t *drive, u8 rate) { return -1; }
1580 #endif
1581
1582 static inline void ide_set_max_pio(ide_drive_t *drive)
1583 {
1584         ide_set_pio(drive, 255);
1585 }
1586
1587 char *ide_media_string(ide_drive_t *);
1588
1589 extern struct device_attribute ide_dev_attrs[];
1590 extern struct bus_type ide_bus_type;
1591 extern struct class *ide_port_class;
1592
1593 static inline void ide_dump_identify(u8 *id)
1594 {
1595         print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 2, id, 512, 0);
1596 }
1597
1598 static inline int hwif_to_node(ide_hwif_t *hwif)
1599 {
1600         return hwif->dev ? dev_to_node(hwif->dev) : -1;
1601 }
1602
1603 static inline ide_drive_t *ide_get_pair_dev(ide_drive_t *drive)
1604 {
1605         ide_drive_t *peer = drive->hwif->devices[(drive->dn ^ 1) & 1];
1606
1607         return (peer->dev_flags & IDE_DFLAG_PRESENT) ? peer : NULL;
1608 }
1609
1610 #define ide_port_for_each_dev(i, dev, port) \
1611         for ((i) = 0; ((dev) = (port)->devices[i]) || (i) < MAX_DRIVES; (i)++)
1612
1613 #define ide_port_for_each_present_dev(i, dev, port) \
1614         for ((i) = 0; ((dev) = (port)->devices[i]) || (i) < MAX_DRIVES; (i)++) \
1615                 if ((dev)->dev_flags & IDE_DFLAG_PRESENT)
1616
1617 #define ide_host_for_each_port(i, port, host) \
1618         for ((i) = 0; ((port) = (host)->ports[i]) || (i) < MAX_HOST_PORTS; (i)++)
1619
1620 #endif /* _IDE_H */