include/linux/pinctrl/pinconf-generic.h

   1 /*
   2  * Interface the generic pinconfig portions of the pinctrl subsystem
   3  *
   4  * Copyright (C) 2011 ST-Ericsson SA
   5  * Written on behalf of Linaro for ST-Ericsson
   6  * This interface is used in the core to keep track of pins.
   7  *
   8  * Author: Linus Walleij <linus.walleij@linaro.org>
   9  *
  10  * License terms: GNU General Public License (GPL) version 2
  11  */
  12 #ifndef __LINUX_PINCTRL_PINCONF_GENERIC_H
  13 #define __LINUX_PINCTRL_PINCONF_GENERIC_H
  14
  15 /**
  16  * enum pin_config_param - possible pin configuration parameters
  17  * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
  18  *      weakly drives the last value on a tristate bus, also known as a "bus
  19  *      holder", "bus keeper" or "repeater". This allows another device on the
  20  *      bus to change the value by driving the bus high or low and switching to
  21  *      tristate. The argument is ignored.
  22  * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a
  23  *      transition from say pull-up to pull-down implies that you disable
  24  *      pull-up in the process, this setting disables all biasing.
  25  * @PIN_CONFIG_BIAS_HIGH_IMPEDANCE: the pin will be set to a high impedance
  26  *      mode, also know as "third-state" (tristate) or "high-Z" or "floating".
  27  *      On output pins this effectively disconnects the pin, which is useful
  28  *      if for example some other pin is going to drive the signal connected
  29  *      to it for a while. Pins used for input are usually always high
  30  *      impedance.
  31  * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
  32  *      impedance to GROUND). If the argument is != 0 pull-down is enabled,
  33  *      if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
  34  * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based
  35  *      on embedded knowledge of the controller hardware, like current mux
  36  *      function. The pull direction and possibly strength too will normally
  37  *      be decided completely inside the hardware block and not be readable
  38  *      from the kernel side.
  39  *      If the argument is != 0 pull up/down is enabled, if it is 0, the
  40  *      configuration is ignored. The proper way to disable it is to use
  41  *      @PIN_CONFIG_BIAS_DISABLE.
  42  * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
  43  *      impedance to VDD). If the argument is != 0 pull-up is enabled,
  44  *      if it is 0, pull-up is total, i.e. the pin is connected to VDD.
  45  * @PIN_CONFIG_BIDIRECTIONAL: the pin will be configured to allow simultaneous
  46  *      input and output operations.
  47  * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
  48  *      collector) which means it is usually wired with other output ports
  49  *      which are then pulled up with an external resistor. Setting this
  50  *      config will enable open drain mode, the argument is ignored.
  51  * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
  52  *      (open emitter). Setting this config will enable open source mode, the
  53  *      argument is ignored.
  54  * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
  55  *      low, this is the most typical case and is typically achieved with two
  56  *      active transistors on the output. Setting this config will enable
  57  *      push-pull mode, the argument is ignored.
  58  * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
  59  *      passed as argument. The argument is in mA.
  60  * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
  61  *      which means it will wait for signals to settle when reading inputs. The
  62  *      argument gives the debounce time in usecs. Setting the
  63  *      argument to zero turns debouncing off.
  64  * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input.  Note that this does not
  65  *      affect the pin's ability to drive output.  1 enables input, 0 disables
  66  *      input.
  67  * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in
  68  *      schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis,
  69  *      the threshold value is given on a custom format as argument when
  70  *      setting pins to this mode.
  71  * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
  72  *      If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
  73  *      schmitt-trigger mode is disabled.
  74  * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
  75  *      operation, if several modes of operation are supported these can be
  76  *      passed in the argument on a custom form, else just use argument 1
  77  *      to indicate low power mode, argument 0 turns low power mode off.
  78  * @PIN_CONFIG_OUTPUT: this will configure the pin as an output. Use argument
  79  *      1 to indicate high level, argument 0 to indicate low level. (Please
  80  *      see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a
  81  *      discussion around this parameter.)
  82  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  83  *      supplies, the argument to this parameter (on a custom format) tells
  84  *      the driver which alternative power source to use.
  85  * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
  86  *      this parameter (on a custom format) tells the driver which alternative
  87  *      slew rate to use.
  88  * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
  89  *      you need to pass in custom configurations to the pin controller, use
  90  *      PIN_CONFIG_END+1 as the base offset.
  91  * @PIN_CONFIG_MAX: this is the maximum configuration value that can be
  92  *      presented using the packed format.
  93  */
  94 enum pin_config_param {
  95         PIN_CONFIG_BIAS_BUS_HOLD,
  96         PIN_CONFIG_BIAS_DISABLE,
  97         PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
  98         PIN_CONFIG_BIAS_PULL_DOWN,
  99         PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
 100         PIN_CONFIG_BIAS_PULL_UP,
 101         PIN_CONFIG_BIDIRECTIONAL,
 102         PIN_CONFIG_DRIVE_OPEN_DRAIN,
 103         PIN_CONFIG_DRIVE_OPEN_SOURCE,
 104         PIN_CONFIG_DRIVE_PUSH_PULL,
 105         PIN_CONFIG_DRIVE_STRENGTH,
 106         PIN_CONFIG_INPUT_DEBOUNCE,
 107         PIN_CONFIG_INPUT_ENABLE,
 108         PIN_CONFIG_INPUT_SCHMITT,
 109         PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 110         PIN_CONFIG_LOW_POWER_MODE,
 111         PIN_CONFIG_OUTPUT,
 112         PIN_CONFIG_POWER_SOURCE,
 113         PIN_CONFIG_SLEW_RATE,
 114         PIN_CONFIG_END = 0x7F,
 115         PIN_CONFIG_MAX = 0xFF,
 116 };
 117
 118 /*
 119  * Helpful configuration macro to be used in tables etc.
 120  */
 121 #define PIN_CONF_PACKED(p, a) ((a << 8) | ((unsigned long) p & 0xffUL))
 122
 123 /*
 124  * The following inlines stuffs a configuration parameter and data value
 125  * into and out of an unsigned long argument, as used by the generic pin config
 126  * system. We put the parameter in the lower 8 bits and the argument in the
 127  * upper 24 bits.
 128  */
 129
 130 static inline enum pin_config_param pinconf_to_config_param(unsigned long config)
 131 {
 132         return (enum pin_config_param) (config & 0xffUL);
 133 }
 134
 135 static inline u32 pinconf_to_config_argument(unsigned long config)
 136 {
 137         return (u32) ((config >> 8) & 0xffffffUL);
 138 }
 139
 140 static inline unsigned long pinconf_to_config_packed(enum pin_config_param param,
 141                                                      u32 argument)
 142 {
 143         return PIN_CONF_PACKED(param, argument);
 144 }
 145
 146 #ifdef CONFIG_GENERIC_PINCONF
 147
 148 #ifdef CONFIG_DEBUG_FS
 149 #define PCONFDUMP(a, b, c, d) {                                 \
 150         .param = a, .display = b, .format = c, .has_arg = d     \
 151         }
 152
 153 struct pin_config_item {
 154         const enum pin_config_param param;
 155         const char * const display;
 156         const char * const format;
 157         bool has_arg;
 158 };
 159 #endif /* CONFIG_DEBUG_FS */
 160
 161 #ifdef CONFIG_OF
 162
 163 #include <linux/device.h>
 164 #include <linux/pinctrl/machine.h>
 165 struct pinctrl_dev;
 166 struct pinctrl_map;
 167
 168 struct pinconf_generic_params {
 169         const char * const property;
 170         enum pin_config_param param;
 171         u32 default_value;
 172 };
 173
 174 int pinconf_generic_dt_subnode_to_map(struct pinctrl_dev *pctldev,
 175                 struct device_node *np, struct pinctrl_map **map,
 176                 unsigned *reserved_maps, unsigned *num_maps,
 177                 enum pinctrl_map_type type);
 178 int pinconf_generic_dt_node_to_map(struct pinctrl_dev *pctldev,
 179                 struct device_node *np_config, struct pinctrl_map **map,
 180                 unsigned *num_maps, enum pinctrl_map_type type);
 181 void pinconf_generic_dt_free_map(struct pinctrl_dev *pctldev,
 182                 struct pinctrl_map *map, unsigned num_maps);
 183
 184 static inline int pinconf_generic_dt_node_to_map_group(
 185                 struct pinctrl_dev *pctldev, struct device_node *np_config,
 186                 struct pinctrl_map **map, unsigned *num_maps)
 187 {
 188         return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps,
 189                         PIN_MAP_TYPE_CONFIGS_GROUP);
 190 }
 191
 192 static inline int pinconf_generic_dt_node_to_map_pin(
 193                 struct pinctrl_dev *pctldev, struct device_node *np_config,
 194                 struct pinctrl_map **map, unsigned *num_maps)
 195 {
 196         return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps,
 197                         PIN_MAP_TYPE_CONFIGS_PIN);
 198 }
 199
 200 static inline int pinconf_generic_dt_node_to_map_all(
 201                 struct pinctrl_dev *pctldev, struct device_node *np_config,
 202                 struct pinctrl_map **map, unsigned *num_maps)
 203 {
 204         /*
 205          * passing the type as PIN_MAP_TYPE_INVALID causes the underlying parser
 206          * to infer the map type from the DT properties used.
 207          */
 208         return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps,
 209                         PIN_MAP_TYPE_INVALID);
 210 }
 211 #endif
 212
 213 #endif /* CONFIG_GENERIC_PINCONF */
 214
 215 #endif /* __LINUX_PINCTRL_PINCONF_GENERIC_H */