ospf6d/README

   1
   2                   Zebra OSPF daemon for IPv6 network
   3
   4                              2003/08/18
   5
   6 README for newer code is not yet. General usage should remain
   7 the same. For further usage, see command helps by typing '?'
   8 in vty, and then imagin ! ;p) Previous README contents follows.
   9
  10                   Zebra OSPF daemon for IPv6 network
  11
  12                              2001/12/20
  13
  14 Zebra OSPF6d is OSPF version 3 daemon which is specified by
  15 "OSPF for IPv6" (RFC 2740).
  16
  17 *** NOTE ***
  18   Zebra ospf6d is in development yet. It may lack some functionalities,
  19   and may have some bugs. Use the latest version from the anoncvs
  20   repository (http://www.zebra.org/cvs.html) !
  21
  22 This file README is like memo yet, so please feel free to ask
  23 <yasu@sfc.wide.ad.jp> by E-mail. Patches will be appriciated.
  24
  25 ospf6d's vty port was default to 2606/tcp.
  26 Use commands below.
  27
  28 VIEW NODE:
  29   show ipv6 ospf6
  30     To see Router-ID, uptime of ospf6d, some statistics.
  31
  32   show ipv6 ospf6 database ...
  33     This command shows LSA database. You can specify
  34     LS-type/LS-ID/Advertising-Router of LSAs. '*' is recognized.
  35
  36   show ipv6 ospf6 interface ...
  37     To see the status of the OSPF interface, and the configuration
  38     like interface costs.
  39
  40   show ipv6 ospf6 neighbor ...
  41     Shows state of neighbors and choosed (Backup) DR on the I/F.
  42
  43   show ipv6 ospf6 route (X::X)
  44     This command shows internal routing table of the ospf6d.
  45     Routes not calculated by OSPFv3 (like connected routes)
  46     are not shown. If Address is specified (X::X), shows the route
  47     that the address matches.
  48
  49   show ipv6 ospf6 route redistribute (X::X)
  50     Shows the routes advertised as AS-External routes by the router
  51     itself. If Address is specified (X::X), shows the route
  52     that the address matches.
  53
  54 CONFIG NODE:
  55   interface NAME
  56     To enter INTERFACE NODE
  57
  58   router ospf6 ...
  59     To enter OSPF6 NODE
  60
  61 INTERFACE NODE:
  62   ipv6 ospf6 cost COST
  63     Sets the interface's output cost. Depends on interface bandwidth by default.
  64
  65   ipv6 ospf6 hello-interval HELLOINTERVAL
  66     Sets the interface's Hello Interval. default 10
  67
  68   ipv6 ospf6 dead-interval DEADINTERVAL
  69     Sets the interface's Router Dead Interval. default 40
  70
  71   ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
  72     Sets the interface's Rxmt Interval. default 5
  73
  74   ipv6 ospf6 priority PRIORITY
  75     Sets the interface's Router Priority. default 1
  76
  77   ipv6 ospf6 transmit-delay TRANSMITDELAY
  78     Sets the interface's Inf-Trans-Delay. default 1
  79
  80 OSPF6 NODE:
  81   router-id A.B.C.D
  82     Sets the router's Router-ID
  83
  84   interface NAME area AREA
  85     Binds interface to specified Area, and start
  86     sending OSPFv3 packets.
  87
  88   auto-cost reference-bandwidth COST
  89     Sets the reference bandwidth for cost calculations, where this
  90     bandwidth is considered equivalent to an OSPF cost of 1, specified
  91     in Mbits/s. The default is 100Mbit/s (i.e. a link of bandwidth
  92     100Mbit/s or higher will have a cost of 1. Cost of lower bandwidth
  93     links will be scaled with reference to this cost).  This
  94     configuration setting MUST be consistent across all routers within
  95     the OSPF domain.
  96
  97 Sample configuration is in ospf6d.conf.sample.
  98
  99 --
 100 Yasuhiro Ohara <yasu@sfc.wide.ad.jp>
 101 Kunihiro Ishiguro <kunihiro@zebra.org>
 102