cut the overhead, others just disable the usage. So
only cgroup_disable=memory is actually worthy}
+ cgroup.memory= [KNL] Pass options to the cgroup memory controller.
+ Format: <string>
+ nosocket -- Disable socket memory accounting.
+
checkreqprot [SELINUX] Set initial checkreqprot flag value.
Format: { "0" | "1" }
See security/selinux/Kconfig help text.
uart[8250],io,<addr>[,options]
uart[8250],mmio,<addr>[,options]
+ uart[8250],mmio16,<addr>[,options]
uart[8250],mmio32,<addr>[,options]
uart[8250],0x<addr>[,options]
Start an early, polled-mode console on the 8250/16550
UART at the specified I/O port or MMIO address,
switching to the matching ttyS device later.
MMIO inter-register address stride is either 8-bit
- (mmio) or 32-bit (mmio32).
- If none of [io|mmio|mmio32], <addr> is assumed to be
- equivalent to 'mmio'. 'options' are specified in the
- same format described for ttyS above; if unspecified,
+ (mmio), 16-bit (mmio16), or 32-bit (mmio32).
+ If none of [io|mmio|mmio16|mmio32], <addr> is assumed
+ to be equivalent to 'mmio'. 'options' are specified in
+ the same format described for ttyS above; if unspecified,
the h/w is not re-initialized.
hvc<n> Use the hypervisor console device <n>. This is for
unspecified, the h/w is not initialized.
pl011,<addr>
+ pl011,mmio32,<addr>
Start an early, polled-mode console on a pl011 serial
port at the specified address. The pl011 serial port
must already be setup and configured. Options are not
- yet supported.
+ yet supported. If 'mmio32' is specified, then only
+ the driver will use only 32-bit accessors to read/write
+ the device registers.
msm_serial,<addr>
Start an early, polled-mode console on an msm serial
notsc [BUGS=X86-32] Disable Time Stamp Counter
- nousb [USB] Disable the USB subsystem
-
nowatchdog [KNL] Disable both lockup detectors, i.e.
soft-lockup and NMI watchdog (hard-lockup).
hardware access methods are allowed. Use this
if you experience crashes upon bootup and you
suspect they are caused by the BIOS.
- conf1 [X86] Force use of PCI Configuration
- Mechanism 1.
- conf2 [X86] Force use of PCI Configuration
- Mechanism 2.
+ conf1 [X86] Force use of PCI Configuration Access
+ Mechanism 1 (config address in IO port 0xCF8,
+ data in IO port 0xCFC, both 32-bit).
+ conf2 [X86] Force use of PCI Configuration Access
+ Mechanism 2 (IO port 0xCF8 is an 8-bit port for
+ the function, IO port 0xCFA, also 8-bit, sets
+ bus number. The config space is then accessed
+ through ports 0xC000-0xCFFF).
+ See http://wiki.osdev.org/PCI for more info
+ on the configuration access mechanisms.
noaer [PCIE] If the PCIEAER kernel config parameter is
enabled, this kernel boot option can be used to
disable the use of PCIE advanced error reporting.
may be specified.
Format: <port>,<port>....
+ ppc_strict_facility_enable
+ [PPC] This option catches any kernel floating point,
+ Altivec, VSX and SPE outside of regions specifically
+ allowed (eg kernel_enable_fpu()/kernel_disable_fpu()).
+ There is some performance impact when enabling this.
+
print-fatal-signals=
[KNL] debug: print fatal signals
raid= [HW,RAID]
See Documentation/md.txt.
- ramdisk_blocksize= [RAM]
- See Documentation/blockdev/ramdisk.txt.
-
ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
See Documentation/blockdev/ramdisk.txt.
usbcore.usbfs_snoop=
[USB] Set to log all usbfs traffic (default 0 = off).
+ usbcore.usbfs_snoop_max=
+ [USB] Maximum number of bytes to snoop in each URB
+ (default = 65536).
+
usbcore.blinkenlights=
[USB] Set to cycle leds on hubs (default 0 = off).
USB_REQ_GET_DESCRIPTOR request in milliseconds
(default 5000 = 5.0 seconds).
+ usbcore.nousb [USB] Disable the USB subsystem
+
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
projects / mirror_ubuntu-zesty-kernel.git / blobdiff