gpio0 = &gpio0;
gpio1 = &gpio1;
};
- intc: interrupt-controller {
- compatible = "marvell,orion-intc", "marvell,intc";
- interrupt-controller;
- #interrupt-cells = <1>;
- reg = <0xf1020204 0x04>,
- <0xf1020214 0x04>;
- };
mbus {
compatible = "marvell,kirkwood-mbus", "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
+ /* If a board file needs to change this ranges it must replace it completely */
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
+ MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
+ MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
+ >;
controller = <&mbusc>;
pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
+
+ crypto@0301 {
+ compatible = "marvell,orion-crypto";
+ reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>,
+ <MBUS_ID(0x03, 0x01) 0 0x800>;
+ reg-names = "regs", "sram";
+ interrupts = <22>;
+ clocks = <&gate_clk 17>;
+ status = "okay";
+ };
+
+ nand: nand@012f {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cle = <0>;
+ ale = <1>;
+ bank-width = <1>;
+ compatible = "marvell,orion-nand";
+ reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
+ chip-delay = <25>;
+ /* set partition map and/or chip-delay in board dts */
+ clocks = <&gate_clk 7>;
+ status = "disabled";
+ };
};
ocp@f1000000 {
compatible = "simple-bus";
- ranges = <0x00000000 0xf1000000 0x0100000
- 0xf4000000 0xf4000000 0x0000400
- 0xf5000000 0xf5000000 0x0000400>;
+ ranges = <0x00000000 0xf1000000 0x0100000>;
#address-cells = <1>;
#size-cells = <1>;
reg = <0x20000 0x80>, <0x1500 0x20>;
};
+ timer: timer@20300 {
+ compatible = "marvell,orion-timer";
+ reg = <0x20300 0x20>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <1>, <2>;
+ clocks = <&core_clk 0>;
+ };
+
+ intc: main-interrupt-ctrl@20200 {
+ compatible = "marvell,orion-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20200 0x10>, <0x20210 0x10>;
+ };
+
+ bridge_intc: bridge-interrupt-ctrl@20110 {
+ compatible = "marvell,orion-bridge-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x20110 0x8>;
+ interrupts = <1>;
+ marvell,#interrupts = <6>;
+ };
+
core_clk: core-clocks@10030 {
compatible = "marvell,kirkwood-core-clock";
reg = <0x10030 0x4>;
#clock-cells = <1>;
};
- wdt@20300 {
+ wdt: watchdog-timer@20300 {
compatible = "marvell,orion-wdt";
reg = <0x20300 0x28>;
+ interrupt-parent = <&bridge_intc>;
+ interrupts = <3>;
clocks = <&gate_clk 7>;
status = "okay";
};
status = "okay";
};
- nand@3000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- cle = <0>;
- ale = <1>;
- bank-width = <1>;
- compatible = "marvell,orion-nand";
- reg = <0xf4000000 0x400>;
- chip-delay = <25>;
- /* set partition map and/or chip-delay in board dts */
- clocks = <&gate_clk 7>;
- status = "disabled";
- };
-
i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
status = "disabled";
};
- crypto@30000 {
- compatible = "marvell,orion-crypto";
- reg = <0x30000 0x10000>,
- <0xf5000000 0x800>;
- reg-names = "regs", "sram";
- interrupts = <22>;
- clocks = <&gate_clk 17>;
- status = "okay";
+ mdio: mdio-bus@72004 {
+ compatible = "marvell,orion-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72004 0x84>;
+ interrupts = <46>;
+ clocks = <&gate_clk 0>;
+ status = "disabled";
+
+ /* add phy nodes in board file */
+ };
+
+ eth0: ethernet-controller@72000 {
+ compatible = "marvell,kirkwood-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72000 0x4000>;
+ clocks = <&gate_clk 0>;
+ marvell,tx-checksum-limit = <1600>;
+ status = "disabled";
+
+ ethernet0-port@0 {
+ device_type = "network";
+ compatible = "marvell,kirkwood-eth-port";
+ reg = <0>;
+ interrupts = <11>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ /* set phy-handle property in board file */
+ };
+ };
+
+ eth1: ethernet-controller@76000 {
+ compatible = "marvell,kirkwood-eth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76000 0x4000>;
+ clocks = <&gate_clk 19>;
+ marvell,tx-checksum-limit = <1600>;
+ status = "disabled";
+
+ ethernet1-port@0 {
+ device_type = "network";
+ compatible = "marvell,kirkwood-eth-port";
+ reg = <0>;
+ interrupts = <15>;
+ /* overwrite MAC address in bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ /* set phy-handle property in board file */
+ };
};
};
};