#include <linux/termios.h>
#include <linux/dmaengine.h>
#include <linux/amba/bus.h>
+#include <linux/amba/mmci.h>
#include <linux/amba/serial.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/fsmc.h>
#include <linux/pinctrl/machine.h>
-#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinconf-generic.h>
#include <linux/dma-mapping.h>
#include <asm/types.h>
#include <mach/gpio-u300.h>
#include "clock.h"
-#include "mmc.h"
#include "spi.h"
#include "i2c.h"
+#include "u300-gpio.h"
/*
* Static I/O mappings that are needed for booting the U300 platforms. The
#endif
};
-static struct amba_device uart0_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "uart0", /* Slow device at 0x3000 offset */
- .platform_data = &uart0_plat_data,
- },
- .res = {
- .start = U300_UART0_BASE,
- .end = U300_UART0_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_U300_UART0, NO_IRQ },
-};
+/* Slow device at 0x3000 offset */
+static AMBA_APB_DEVICE(uart0, "uart0", 0, U300_UART0_BASE,
+ { IRQ_U300_UART0 }, &uart0_plat_data);
/* The U335 have an additional UART1 on the APP CPU */
#ifdef CONFIG_MACH_U300_BS335
#endif
};
-static struct amba_device uart1_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "uart1", /* Fast device at 0x7000 offset */
- .platform_data = &uart1_plat_data,
- },
- .res = {
- .start = U300_UART1_BASE,
- .end = U300_UART1_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_U300_UART1, NO_IRQ },
-};
+/* Fast device at 0x7000 offset */
+static AMBA_APB_DEVICE(uart1, "uart1", 0, U300_UART1_BASE,
+ { IRQ_U300_UART1 }, &uart1_plat_data);
#endif
-static struct amba_device pl172_device = {
- .dev = {
- .init_name = "pl172", /* AHB device at 0x4000 offset */
- .platform_data = NULL,
- },
- .res = {
- .start = U300_EMIF_CFG_BASE,
- .end = U300_EMIF_CFG_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
+/* AHB device at 0x4000 offset */
+static AMBA_APB_DEVICE(pl172, "pl172", 0, U300_EMIF_CFG_BASE, { }, NULL);
+/* Fast device at 0x6000 offset */
+static AMBA_APB_DEVICE(pl022, "pl022", 0, U300_SPI_BASE,
+ { IRQ_U300_SPI }, NULL);
-/*
- * Everything within this next ifdef deals with external devices connected to
- * the APP SPI bus.
- */
-static struct amba_device pl022_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "pl022", /* Fast device at 0x6000 offset */
- },
- .res = {
- .start = U300_SPI_BASE,
- .end = U300_SPI_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_U300_SPI, NO_IRQ },
- /*
- * This device has a DMA channel but the Linux driver does not use
- * it currently.
- */
-};
+/* Fast device at 0x1000 offset */
+#define U300_MMCSD_IRQS { IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 }
-static struct amba_device mmcsd_device = {
- .dev = {
- .init_name = "mmci", /* Fast device at 0x1000 offset */
- .platform_data = NULL, /* Added later */
- },
- .res = {
- .start = U300_MMCSD_BASE,
- .end = U300_MMCSD_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 },
+static struct mmci_platform_data mmcsd_platform_data = {
/*
- * This device has a DMA channel but the Linux driver does not use
- * it currently.
+ * Do not set ocr_mask or voltage translation function,
+ * we have a regulator we can control instead.
*/
+ .f_max = 24000000,
+ .gpio_wp = -1,
+ .gpio_cd = U300_GPIO_PIN_MMC_CD,
+ .cd_invert = true,
+ .capabilities = MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+#ifdef CONFIG_COH901318
+ .dma_filter = coh901318_filter_id,
+ .dma_rx_param = (void *) U300_DMA_MMCSD_RX_TX,
+ /* Don't specify a TX channel, this RX channel is bidirectional */
+#endif
};
+static AMBA_APB_DEVICE(mmcsd, "mmci", 0, U300_MMCSD_BASE,
+ U300_MMCSD_IRQS, &mmcsd_platform_data);
+
/*
* The order of device declaration may be important, since some devices
* have dependencies on other devices being initialized first.
.max_channels = U300_DMA_CHANNELS,
};
-static struct resource pinmux_resources[] = {
+static struct resource pinctrl_resources[] = {
{
.start = U300_SYSCON_BASE,
.end = U300_SYSCON_BASE + SZ_4K - 1,
.resource = i2c1_resources,
};
+static struct platform_device pinctrl_device = {
+ .name = "pinctrl-u300",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(pinctrl_resources),
+ .resource = pinctrl_resources,
+};
+
/*
* The different variants have a few different versions of the
* GPIO block, with different number of ports.
#endif
.gpio_base = 0,
.gpio_irq_base = IRQ_U300_GPIO_BASE,
+ .pinctrl_device = &pinctrl_device,
};
static struct platform_device gpio_device = {
},
};
-static struct platform_device pinmux_device = {
- .name = "pinmux-u300",
- .id = -1,
- .num_resources = ARRAY_SIZE(pinmux_resources),
- .resource = pinmux_resources,
+static unsigned long pin_pullup_conf[] = {
+ PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_UP, 1),
+};
+
+static unsigned long pin_highz_conf[] = {
+ PIN_CONF_PACKED(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, 0),
};
-/* Pinmux settings */
-static struct pinmux_map __initdata u300_pinmux_map[] = {
+/* Pin control settings */
+static struct pinctrl_map __initdata u300_pinmux_map[] = {
/* anonymous maps for chip power and EMIFs */
- PINMUX_MAP_SYS_HOG("POWER", "pinmux-u300", "power"),
- PINMUX_MAP_SYS_HOG("EMIF0", "pinmux-u300", "emif0"),
- PINMUX_MAP_SYS_HOG("EMIF1", "pinmux-u300", "emif1"),
+ PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "power"),
+ PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif0"),
+ PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif1"),
/* per-device maps for MMC/SD, SPI and UART */
- PINMUX_MAP("MMCSD", "pinmux-u300", "mmc0", "mmci"),
- PINMUX_MAP("SPI", "pinmux-u300", "spi0", "pl022"),
- PINMUX_MAP("UART0", "pinmux-u300", "uart0", "uart0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("mmci", "pinctrl-u300", NULL, "mmc0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("pl022", "pinctrl-u300", NULL, "spi0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("uart0", "pinctrl-u300", NULL, "uart0"),
+ /* This pin is used for clock return rather than GPIO */
+ PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO APP GPIO 11",
+ pin_pullup_conf),
+ /* This pin is used for card detect */
+ PIN_MAP_CONFIGS_PIN_DEFAULT("mmci", "pinctrl-u300", "PIO MS INS",
+ pin_highz_conf),
};
struct u300_mux_hog {
- const char *name;
struct device *dev;
- struct pinmux *pmx;
+ struct pinctrl *p;
};
static struct u300_mux_hog u300_mux_hogs[] = {
{
- .name = "uart0",
.dev = &uart0_device.dev,
},
{
- .name = "spi0",
.dev = &pl022_device.dev,
},
{
- .name = "mmc0",
.dev = &mmcsd_device.dev,
},
};
-static int __init u300_pinmux_fetch(void)
+static int __init u300_pinctrl_fetch(void)
{
int i;
for (i = 0; i < ARRAY_SIZE(u300_mux_hogs); i++) {
- struct pinmux *pmx;
- int ret;
+ struct pinctrl *p;
- pmx = pinmux_get(u300_mux_hogs[i].dev, NULL);
- if (IS_ERR(pmx)) {
- pr_err("u300: could not get pinmux hog %s\n",
- u300_mux_hogs[i].name);
- continue;
- }
- ret = pinmux_enable(pmx);
- if (ret) {
- pr_err("u300: could enable pinmux hog %s\n",
- u300_mux_hogs[i].name);
+ p = pinctrl_get_select_default(u300_mux_hogs[i].dev);
+ if (IS_ERR(p)) {
+ pr_err("u300: could not get pinmux hog for dev %s\n",
+ dev_name(u300_mux_hogs[i].dev));
continue;
}
- u300_mux_hogs[i].pmx = pmx;
+ u300_mux_hogs[i].p = p;
}
return 0;
}
-subsys_initcall(u300_pinmux_fetch);
+subsys_initcall(u300_pinctrl_fetch);
/*
* Notice that AMBA devices are initialized before platform devices.
&gpio_device,
&nand_device,
&wdog_device,
- &pinmux_device,
};
/*
u300_assign_physmem();
/* Initialize pinmuxing */
- pinmux_register_mappings(u300_pinmux_map,
- ARRAY_SIZE(u300_pinmux_map));
+ pinctrl_register_mappings(u300_pinmux_map,
+ ARRAY_SIZE(u300_pinmux_map));
/* Register subdevices on the I2C buses */
u300_i2c_register_board_devices();
writew(val, U300_SYSCON_VBASE + U300_SYSCON_SMCR);
}
-static int core_module_init(void)
-{
- /*
- * This needs to be initialized later: it needs the input framework
- * to be initialized first.
- */
- return mmc_init(&mmcsd_device);
-}
-module_init(core_module_init);
-
/* Forward declare this function from the watchdog */
void coh901327_watchdog_reset(void);
projects / mirror_ubuntu-artful-kernel.git / blobdiff