help
Enable module allocation with kmalloc instead of vmalloc.
-config OOM_REBOOT
- bool "Enable reboot at out of memory"
-
source "kernel/Kconfig.preempt"
source mm/Kconfig
config ETRAXFS
bool "ETRAX-FS-V32"
+ select CPU_FREQ_TABLE if CPU_FREQ
help
Support CRIS V32.
config CRIS_MACH_ARTPEC3
bool "ARTPEC-3"
+ select CPU_FREQ_TABLE if CPU_FREQ
help
Support Axis ARTPEC-3.
help
Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2.
-config ETRAX_NANDFLASH_BUSWIDTH
- int "Buswidth of NAND flash in bytes"
- default "1"
- help
- Width in bytes of the NAND flash (1 or 2).
-
config ETRAX_FLASH1_SIZE
int "FLASH1 size (dec, in MB. 0 = Unknown)"
default "0"
This option enables MTD mapping of flash devices. Needed to use
flash memories. If unsure, say Y.
-config ETRAX_RTC
- bool "Real Time Clock support"
- depends on ETRAX_I2C
- help
- Enables drivers for the Real-Time Clock battery-backed chips on
- some products. The kernel reads the time when booting, and
- the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a
- rtc_time struct (see <file:arch/cris/include/asm/rtc.h>) on the
- /dev/rtc device. You can check the time with cat /proc/rtc, but
- normal time reading should be done using libc function time and
- friends.
-
-choice
- prompt "RTC chip"
- depends on ETRAX_RTC
- default ETRAX_DS1302
-
-config ETRAX_DS1302
- depends on ETRAX_ARCH_V10
- bool "DS1302"
- help
- Enables the driver for the DS1302 Real-Time Clock battery-backed
- chip on some products.
-
-config ETRAX_PCF8563
- bool "PCF8563"
- help
- Enables the driver for the PCF8563 Real-Time Clock battery-backed
- chip on some products.
-
-endchoice
-
config ETRAX_SYNCHRONOUS_SERIAL
bool "Synchronous serial-port support"
help
depends on ETRAX_ARCH_V10
bool "DMA 5"
-config ETRAX_SERIAL_PORT3_DMA9_IN
- bool "Ser3 uses DMA9 for input"
- depends on ETRAXFS
- help
- Enables the DMA9 input channel for ser3 (ttyS3).
- If you do not enable DMA, an interrupt for each character will be
- used when receiving data.
- Normally you want to use DMA, unless you use the DMA channel for
- something else.
-
-config ETRAX_SERIAL_PORT3_DMA3_IN
- bool "Ser3 uses DMA3 for input"
- depends on CRIS_MACH_ARTPEC3
- help
- Enables the DMA3 input channel for ser3 (ttyS3).
- If you do not enable DMA, an interrupt for each character will be
- used when receiving data.
- Normally you want to use DMA, unless you use the DMA channel for
- something else.
-
endchoice
choice
depends on ETRAX_ARCH_V10
bool "DMA 4"
-config ETRAX_SERIAL_PORT3_DMA8_OUT
- bool "Ser3 uses DMA8 for output"
- depends on ETRAXFS
- help
- Enables the DMA8 output channel for ser3 (ttyS3).
- If you do not enable DMA, an interrupt for each character will be
- used when transmitting data.
- Normally you want to use DMA, unless you use the DMA channel for
- something else.
-
-config ETRAX_SERIAL_PORT3_DMA2_OUT
- bool "Ser3 uses DMA2 for output"
- depends on CRIS_MACH_ARTPEC3
- help
- Enables the DMA2 output channel for ser3 (ttyS3).
- If you do not enable DMA, an interrupt for each character will be
- used when transmitting data.
- Normally you want to use DMA, unless you use the DMA channel for
- something else.
-
endchoice
endmenu
-source "drivers/base/Kconfig"
-
-# standard linux drivers
-source "drivers/mtd/Kconfig"
-
-source "drivers/parport/Kconfig"
-
-source "drivers/pnp/Kconfig"
-
-source "drivers/block/Kconfig"
-
-source "drivers/ide/Kconfig"
-
-source "drivers/net/Kconfig"
-
-source "drivers/i2c/Kconfig"
-
-source "drivers/rtc/Kconfig"
-
-#
-# input before char - char/joystick depends on it. As does USB.
-#
-source "drivers/input/Kconfig"
-
-source "drivers/char/Kconfig"
+source "drivers/Kconfig"
source "fs/Kconfig"
-source "drivers/usb/Kconfig"
-
-source "drivers/uwb/Kconfig"
-
-source "drivers/staging/Kconfig"
-
source "arch/cris/Kconfig.debug"
source "security/Kconfig"