prefix of group ranges covered. This command is vrf aware, to configure for
a vrf, enter the vrf submode.
+.. clicmd:: ip pim rp keep-alive-timer (1-65535)
+
+ Modify the time out value for a S,G flow from 1-65535 seconds at RP.
+ The normal keepalive period for the KAT(S,G) defaults to 210 seconds.
+ However, at the RP, the keepalive period must be at least the
+ Register_Suppression_Time, or the RP may time out the (S,G) state
+ before the next Null-Register arrives. Thus, the KAT(S,G) is set to
+ max(Keepalive_Period, RP_Keepalive_Period) when a Register-Stop is sent.
+ If choosing a value below 31 seconds be aware that some hardware platforms
+ cannot see data flowing in better than 30 second chunks. This command is
+ vrf aware, to configure for a vrf, enter the vrf submode.
+
.. clicmd:: ip pim register-accept-list PLIST
When pim receives a register packet the source of the packet will be compared
processing continues. If a deny is returned for the source address of the
register packet a register stop message is sent to the source.
-.. clicmd:: ip pim spt-switchover infinity-and-beyond
+.. clicmd:: ip pim spt-switchover infinity-and-beyond [prefix-list PLIST]
- On the last hop router if it is desired to not switch over to the SPT tree.
- Configure this command. This command is vrf aware, to configure for a vrf,
+ On the last hop router if it is desired to not switch over to the SPT tree
+ configure this command. Optional parameter prefix-list can be use to control
+ which groups to switch or not switch. If a group is PERMIT as per the
+ PLIST, then the SPT switchover does not happen for it and if it is DENY,
+ then the SPT switchover happens.
+ This command is vrf aware, to configure for a vrf,
enter the vrf submode.
.. clicmd:: ip pim ecmp
down. This command is vrf aware, to configure for a vrf, enter the vrf
submode.
-.. clicmd:: ip pim join-prune-interval (5-600)
+.. clicmd:: ip pim join-prune-interval (1-65535)
Modify the join/prune interval that pim uses to the new value. Time is
specified in seconds. This command is vrf aware, to configure for a vrf,
a value smaller than 60 seconds be aware that this can and will affect
convergence at scale.
-.. clicmd:: ip pim keep-alive-timer (31-60000)
+.. clicmd:: ip pim keep-alive-timer (1-65535)
- Modify the time out value for a S,G flow from 31-60000 seconds. 31 seconds
- is chosen for a lower bound because some hardware platforms cannot see data
+ Modify the time out value for a S,G flow from 1-65535 seconds. If choosing
+ a value below 31 seconds be aware that some hardware platforms cannot see data
flowing in better than 30 second chunks. This command is vrf aware, to
configure for a vrf, enter the vrf submode.
-.. clicmd:: ip pim packets (1-100)
+.. clicmd:: ip pim packets (1-255)
When processing packets from a neighbor process the number of packets
incoming at one time before moving on to the next task. The default value is
a large number of pim control packets flowing. This command is vrf aware, to
configure for a vrf, enter the vrf submode.
-.. clicmd:: ip pim register-suppress-time (5-60000)
+.. clicmd:: ip pim register-suppress-time (1-65535)
Modify the time that pim will register suppress a FHR will send register
notifications to the kernel. This command is vrf aware, to configure for a
the existing IGMP general query timer.If no version is provided in the cli,
it will be considered as default v2 query.This is a hidden command.
-.. clicmd:: ip igmp watermark-warn (10-60000)
+.. clicmd:: ip igmp watermark-warn (1-65535)
Configure watermark warning generation for an igmp group limit. Generates
warning once the configured group limit is reached while adding new groups.
Set the DR Priority for the interface. This command is useful to allow the
user to influence what node becomes the DR for a lan segment.
-.. clicmd:: ip pim hello (1-180) (1-630)
+.. clicmd:: ip pim hello (1-65535) (1-65535)
Set the pim hello and hold interval for a interface.
Join multicast group or source-group on an interface.
-.. clicmd:: ip igmp query-interval (1-1800)
+.. clicmd:: ip igmp query-interval (1-65535)
Set the IGMP query interval that PIM will use.
-.. clicmd:: ip igmp query-max-response-time (10-250)
+.. clicmd:: ip igmp query-max-response-time (1-65535)
Set the IGMP query response timeout value. If an report is not returned in
the specified time we will assume the S,G or \*,G has timed out.
or IGMP report is received on this interface and the Group is denied by the
prefix-list, PIM will ignore the join or report.
-.. clicmd:: ip igmp last-member-query-count (1-7)
+.. clicmd:: ip igmp last-member-query-count (1-255)
Set the IGMP last member query count. The default value is 2. 'no' form of
this command is used to to configure back to the default value.
-.. clicmd:: ip igmp last-member-query-interval (1-255)
+.. clicmd:: ip igmp last-member-query-interval (1-65535)
Set the IGMP last member query interval in deciseconds. The default value is
10 deciseconds. 'no' form of this command is used to to configure back to the
Commands available for MSDP:
-.. clicmd:: ip msdp timers (2-600) (3-600) [(1-600)]
+.. clicmd:: ip msdp timers (1-65535) (1-65535) [(1-65535)]
Configure global MSDP timers.
- First value is the keep-alive interval and it must be less than the
- second value which is hold-time. This configures the interval in
- seconds between keep-alive messages. The default value is 60 seconds.
+ First value is the keep-alive interval. This configures the interval in
+ seconds between keep-alive messages. The default value is 60 seconds. It
+ should be less than the remote hold time.
- Second value is the hold-time and it must be greater than the keep-alive
- interval. This configures the interval in seconds before closing a non
- responding connection. The default value is 75.
+ Second value is the hold-time. This configures the interval in seconds before
+ closing a non responding connection. The default value is 75. This value
+ should be greater than the remote keep alive time.
Third value is the connection retry interval and it is optional. This
configures the interval between connection attempts. The default value
Display IGMP group retransmission information.
-.. clicmd:: show ip igmp sources
+.. clicmd:: show ip igmp [vrf NAME] sources [json]
Display IGMP sources information.
.. clicmd:: show ip pim assert
Display information about asserts in the PIM system for S,G mroutes.
+ This command does not show S,G Channel states that in a NOINFO state.
.. clicmd:: show ip pim assert-internal
projects / mirror_frr.git / blobdiff