}
/**
- * it821x_tunepio - tune a drive
- * @drive: drive to tune
- * @pio: the desired PIO mode
+ * it821x_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
- * Try to tune the drive/host to the desired PIO mode taking into
- * the consideration the maximum PIO mode supported by the other
- * device on the cable.
+ * Tune the host to the desired PIO mode taking into the consideration
+ * the maximum PIO mode supported by the other device on the cable.
*/
-static int it821x_tunepio(ide_drive_t *drive, u8 set_pio)
+static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = drive->hwif;
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int unit = drive->select.b.unit;
ide_drive_t *pair = &hwif->drives[1 - unit];
+ u8 set_pio = pio;
/* Spec says 89 ref driver uses 88 */
- static u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+ static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
/*
set_pio = pair_pio;
}
- if (itdev->smart)
- return 0;
-
/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
itdev->want[unit][1] = pio_want[set_pio];
itdev->want[unit][0] = 1; /* PIO is lowest priority */
- itdev->pio[unit] = pio[set_pio];
+ itdev->pio[unit] = pio_timings[set_pio];
it821x_clock_strategy(drive);
it821x_program(drive, itdev->pio[unit]);
-
- return ide_config_drive_speed(drive, XFER_PIO_0 + set_pio);
-}
-
-static void it821x_tuneproc(ide_drive_t *drive, u8 pio)
-{
- pio = ide_get_best_pio_mode(drive, pio, 4);
- (void)it821x_tunepio(drive, pio);
}
/**
return ret;
}
-
-/**
- * it821x_tune_chipset - set controller timings
- * @drive: Drive to set up
- * @xferspeed: speed we want to achieve
- *
- * Tune the ITE chipset for the desired mode. If we can't achieve
- * the desired mode then tune for a lower one, but ultimately
- * make the thing work.
- */
-
-static int it821x_tune_chipset (ide_drive_t *drive, byte xferspeed)
-{
-
- ide_hwif_t *hwif = drive->hwif;
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- u8 speed = ide_rate_filter(drive, xferspeed);
-
- switch (speed) {
- case XFER_PIO_4:
- case XFER_PIO_3:
- case XFER_PIO_2:
- case XFER_PIO_1:
- case XFER_PIO_0:
- return it821x_tunepio(drive, speed - XFER_PIO_0);
- }
-
- if (itdev->smart == 0) {
- switch (speed) {
- /* MWDMA tuning is really hard because our MWDMA and PIO
- timings are kept in the same place. We can switch in the
- host dma on/off callbacks */
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
- it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0));
- break;
- case XFER_UDMA_6:
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- it821x_tune_udma(drive, (speed - XFER_UDMA_0));
- break;
- default:
- return 1;
- }
-
- return ide_config_drive_speed(drive, speed);
- }
-
- /* don't touch anything in the smart mode */
- return 0;
-}
-
/**
- * it821x_configure_drive_for_dma - set up for DMA transfers
- * @drive: drive we are going to set up
+ * it821x_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Set up the drive for DMA, tune the controller and drive as
- * required. If the drive isn't suitable for DMA or we hit
- * other problems then we will drop down to PIO and set up
- * PIO appropriately
+ * Tune the ITE chipset for the desired DMA mode.
*/
-static int it821x_config_drive_for_dma (ide_drive_t *drive)
+static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
- if (ide_tune_dma(drive))
- return 0;
-
- it821x_tuneproc(drive, 255);
-
- return -1;
+ /*
+ * MWDMA tuning is really hard because our MWDMA and PIO
+ * timings are kept in the same place. We can switch in the
+ * host dma on/off callbacks.
+ */
+ if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
+ it821x_tune_udma(drive, speed - XFER_UDMA_0);
+ else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
}
/**
printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n");
}
- hwif->speedproc = &it821x_tune_chipset;
- hwif->tuneproc = &it821x_tuneproc;
+ if (idev->smart == 0) {
+ hwif->set_pio_mode = &it821x_set_pio_mode;
+ hwif->set_dma_mode = &it821x_set_dma_mode;
- /* MWDMA/PIO clock switching for pass through mode */
- if(!idev->smart) {
+ /* MWDMA/PIO clock switching for pass through mode */
hwif->dma_start = &it821x_dma_start;
hwif->ide_dma_end = &it821x_dma_end;
- }
+ } else
+ hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
hwif->ultra_mask = 0x7f;
hwif->mwdma_mask = 0x07;
- hwif->ide_dma_check = &it821x_config_drive_for_dma;
-
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_it821x(hwif);
return 0;
}
-static struct pci_device_id it821x_pci_tbl[] = {
- { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+static const struct pci_device_id it821x_pci_tbl[] = {
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 },
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 },
{ 0, },
};
projects / mirror_ubuntu-bionic-kernel.git / blobdiff