-
/*
- * linux/drivers/ide/pci/it821x.c Version 0.16 Jul 3 2007
- *
* Copyright (C) 2004 Red Hat <alan@redhat.com>
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*
#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
-#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
-#include <asm/io.h>
-
struct it821x_dev
{
unsigned int smart:1, /* Are we in smart raid mode */
static void it821x_program(ide_drive_t *drive, u16 timing)
{
- ide_hwif_t *hwif = drive->hwif;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int channel = hwif->channel;
u8 conf;
conf = timing >> 8;
else
conf = timing & 0xFF;
- pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf);
+
+ pci_write_config_byte(dev, 0x54 + 4 * channel, conf);
}
/**
static void it821x_program_udma(ide_drive_t *drive, u16 timing)
{
- ide_hwif_t *hwif = drive->hwif;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int channel = hwif->channel;
int unit = drive->select.b.unit;
conf = timing >> 8;
else
conf = timing & 0xFF;
- if(itdev->timing10 == 0)
- pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, conf);
+
+ if (itdev->timing10 == 0)
+ pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf);
else {
- pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel, conf);
- pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + 1, conf);
+ pci_write_config_byte(dev, 0x56 + 4 * channel, conf);
+ pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf);
}
}
static void it821x_clock_strategy(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
u8 unit = drive->select.b.unit;
itdev->clock_mode = ATA_50;
sel = 1;
}
- pci_read_config_byte(hwif->pci_dev, 0x50, &v);
+
+ pci_read_config_byte(dev, 0x50, &v);
v &= ~(1 << (1 + hwif->channel));
v |= sel << (1 + hwif->channel);
- pci_write_config_byte(hwif->pci_dev, 0x50, v);
+ pci_write_config_byte(dev, 0x50, v);
/*
* Reprogram the UDMA/PIO of the pair drive for the switch
static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted)
{
- ide_hwif_t *hwif = drive->hwif;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
int unit = drive->select.b.unit;
int channel = hwif->channel;
itdev->udma[unit] = UDMA_OFF;
/* UDMA bits off - Revision 0x10 do them in pairs */
- pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
- if(itdev->timing10)
+ pci_read_config_byte(dev, 0x50, &conf);
+ if (itdev->timing10)
conf |= channel ? 0x60: 0x18;
else
conf |= 1 << (3 + 2 * channel + unit);
- pci_write_config_byte(hwif->pci_dev, 0x50, conf);
+ pci_write_config_byte(dev, 0x50, conf);
it821x_clock_strategy(drive);
/* FIXME: do we need to program this ? */
static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted)
{
- ide_hwif_t *hwif = drive->hwif;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int unit = drive->select.b.unit;
int channel = hwif->channel;
itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
/* UDMA on. Again revision 0x10 must do the pair */
- pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
- if(itdev->timing10)
+ pci_read_config_byte(dev, 0x50, &conf);
+ if (itdev->timing10)
conf &= channel ? 0x9F: 0xE7;
else
conf &= ~ (1 << (3 + 2 * channel + unit));
- pci_write_config_byte(hwif->pci_dev, 0x50, conf);
+ pci_write_config_byte(dev, 0x50, conf);
it821x_clock_strategy(drive);
it821x_program_udma(drive, itdev->udma[unit]);
}
/**
- * it821x_fixup - post init callback
- * @hwif: interface
+ * it821x_quirkproc - post init callback
+ * @drive: drive
*
- * This callback is run after the drives have been probed but
+ * This callback is run after the drive has been probed but
* before anything gets attached. It allows drivers to do any
* final tuning that is needed, or fixups to work around bugs.
*/
-static void __devinit it821x_fixups(ide_hwif_t *hwif)
+static void __devinit it821x_quirkproc(ide_drive_t *drive)
{
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
- int i;
+ struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif);
+ struct hd_driveid *id = drive->id;
+ u16 *idbits = (u16 *)drive->id;
- if(!itdev->smart) {
+ if (!itdev->smart) {
/*
* If we are in pass through mode then not much
* needs to be done, but we do bother to clear the
* IRQ mask as we may well be in PIO (eg rev 0x10)
* for now and we know unmasking is safe on this chipset.
*/
- for (i = 0; i < 2; i++) {
- ide_drive_t *drive = &hwif->drives[i];
- if(drive->present)
- drive->unmask = 1;
- }
- return;
- }
+ drive->unmask = 1;
+ } else {
/*
* Perform fixups on smart mode. We need to "lose" some
* capabilities the firmware lacks but does not filter, and
* in RAID mode.
*/
- for(i = 0; i < 2; i++) {
- ide_drive_t *drive = &hwif->drives[i];
- struct hd_driveid *id;
- u16 *idbits;
-
- if(!drive->present)
- continue;
- id = drive->id;
- idbits = (u16 *)drive->id;
-
/* Check for RAID v native */
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *idev = kzalloc(sizeof(struct it821x_dev), GFP_KERNEL);
u8 conf;
+ hwif->quirkproc = &it821x_quirkproc;
+
if (idev == NULL) {
printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n");
return;
ide_set_hwifdata(hwif, idev);
- pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+ pci_read_config_byte(dev, 0x50, &conf);
if (conf & 1) {
idev->smart = 1;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
* this is necessary.
*/
- pci_read_config_byte(hwif->pci_dev, 0x08, &conf);
+ pci_read_config_byte(dev, 0x08, &conf);
if (conf == 0x10) {
idev->timing10 = 1;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
} else
hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
+ hwif->cable_detect = ata66_it821x;
+
if (hwif->dma_base == 0)
return;
hwif->ultra_mask = ATA_UDMA6;
hwif->mwdma_mask = ATA_MWDMA2;
-
- if (hwif->cbl != ATA_CBL_PATA40_SHORT)
- hwif->cbl = ata66_it821x(hwif);
}
static void __devinit it8212_disable_raid(struct pci_dev *dev)
.name = name_str, \
.init_chipset = init_chipset_it821x, \
.init_hwif = init_hwif_it821x, \
- .fixup = it821x_fixups, \
- .host_flags = IDE_HFLAG_BOOTABLE, \
.pio_mask = ATA_PIO4, \
}
module_init(it821x_ide_init);
module_param_named(noraid, it8212_noraid, int, S_IRUGO);
-MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");
+MODULE_PARM_DESC(noraid, "Force card into bypass mode");
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("PCI driver module for the ITE 821x");