if (data_port == pmac_ide[ix].regbase)
break;
- if (ix >= MAX_HWIFS) {
- /* Probably a PCI interface... */
- for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; ++i)
- hw->io_ports[i] = data_port + i - IDE_DATA_OFFSET;
- hw->io_ports[IDE_CONTROL_OFFSET] = ctrl_port;
- return;
- }
+ if (ix >= MAX_HWIFS)
+ return; /* not an IDE PMAC interface */
for (i = 0; i < 8; ++i)
hw->io_ports[i] = data_port + i * 0x10;
tl[0] = *timings;
tl[1] = *timings2;
- switch(speed) {
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
- case XFER_UDMA_6:
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- if (pmif->kind == controller_kl_ata4)
- ret = set_timings_udma_ata4(&tl[0], speed);
- else if (pmif->kind == controller_un_ata6
- || pmif->kind == controller_k2_ata6)
- ret = set_timings_udma_ata6(&tl[0], &tl[1], speed);
- else if (pmif->kind == controller_sh_ata6)
- ret = set_timings_udma_shasta(&tl[0], &tl[1], speed);
- else
- ret = 1;
- break;
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
- set_timings_mdma(drive, pmif->kind, &tl[0], &tl[1], speed);
- break;
- case XFER_SW_DMA_2:
- case XFER_SW_DMA_1:
- case XFER_SW_DMA_0:
- return;
+ if (speed >= XFER_UDMA_0) {
+ if (pmif->kind == controller_kl_ata4)
+ ret = set_timings_udma_ata4(&tl[0], speed);
+ else if (pmif->kind == controller_un_ata6
+ || pmif->kind == controller_k2_ata6)
+ ret = set_timings_udma_ata6(&tl[0], &tl[1], speed);
+ else if (pmif->kind == controller_sh_ata6)
+ ret = set_timings_udma_shasta(&tl[0], &tl[1], speed);
+ else
+ ret = -1;
+ } else
+ set_timings_mdma(drive, pmif->kind, &tl[0], &tl[1], speed);
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
- default:
- ret = 1;
- }
if (ret)
return;
{
struct device_node *np = pmif->node;
const int *bidp;
+ u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ hw_regs_t hw;
pmif->cable_80 = 0;
pmif->broken_dma = pmif->broken_dma_warn = 0;
/* Tell common code _not_ to mess with resources */
hwif->mmio = 1;
hwif->hwif_data = pmif;
- pmac_ide_init_hwif_ports(&hwif->hw, pmif->regbase, 0, &hwif->irq);
- memcpy(hwif->io_ports, hwif->hw.io_ports, sizeof(hwif->io_ports));
+ memset(&hw, 0, sizeof(hw));
+ pmac_ide_init_hwif_ports(&hw, pmif->regbase, 0, &hwif->irq);
+ memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
hwif->chipset = ide_pmac;
hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET] || pmif->mediabay;
hwif->hold = pmif->mediabay;
hwif->drives[0].autotune = IDE_TUNE_AUTO;
hwif->drives[1].autotune = IDE_TUNE_AUTO;
hwif->host_flags = IDE_HFLAG_SET_PIO_MODE_KEEP_DMA |
+ IDE_HFLAG_PIO_NO_DOWNGRADE |
IDE_HFLAG_POST_SET_MODE;
hwif->pio_mask = ATA_PIO4;
hwif->set_pio_mode = pmac_ide_set_pio_mode;
pmac_ide_setup_dma(pmif, hwif);
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
- /* We probe the hwif now */
- probe_hwif_init(hwif);
+ idx[0] = hwif->index;
- ide_proc_register_port(hwif);
+ ide_device_add(idx);
return 0;
}
if (pmif->broken_dma && cur_addr & (L1_CACHE_BYTES - 1)) {
if (pmif->broken_dma_warn == 0) {
- printk(KERN_WARNING "%s: DMA on non aligned address,"
+ printk(KERN_WARNING "%s: DMA on non aligned address, "
"switching to PIO on Ohare chipset\n", drive->name);
pmif->broken_dma_warn = 1;
}
hwif->dma_timeout = &ide_dma_timeout;
hwif->dma_lost_irq = &pmac_ide_dma_lost_irq;
- hwif->atapi_dma = 1;
switch(pmif->kind) {
case controller_sh_ata6:
hwif->ultra_mask = pmif->cable_80 ? 0x7f : 0x07;