#include <media/v4l2-common.h>
#include "em28xx.h"
-#include "tuner-xc2028.h"
static int tuner = -1;
module_param(tuner, int, 0444);
unsigned int tuner;
};
-/* Boards supported by driver */
-
-#define EM2800_BOARD_UNKNOWN 0
-#define EM2820_BOARD_UNKNOWN 1
-#define EM2820_BOARD_TERRATEC_CINERGY_250 2
-#define EM2820_BOARD_PINNACLE_USB_2 3
-#define EM2820_BOARD_HAUPPAUGE_WINTV_USB_2 4
-#define EM2820_BOARD_MSI_VOX_USB_2 5
-#define EM2800_BOARD_TERRATEC_CINERGY_200 6
-#define EM2800_BOARD_LEADTEK_WINFAST_USBII 7
-#define EM2800_BOARD_KWORLD_USB2800 8
-#define EM2820_BOARD_PINNACLE_DVC_90 9
-#define EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900 10
-#define EM2880_BOARD_TERRATEC_HYBRID_XS 11
-#define EM2820_BOARD_KWORLD_PVRTV2800RF 12
-#define EM2880_BOARD_TERRATEC_PRODIGY_XS 13
-#define EM2820_BOARD_PROLINK_PLAYTV_USB2 14
-#define EM2800_BOARD_VGEAR_POCKETTV 15
-#define EM2880_BOARD_HAUPPAUGE_WINTV_HVR_950 16
-
struct em28xx_board em28xx_boards[] = {
[EM2800_BOARD_UNKNOWN] = {
.name = "Unknown EM2800 video grabber",
.tuner_type = TUNER_XC2028,
.mts_firmware = 1,
.has_12mhz_i2s = 1,
+ .has_dvb = 1,
.decoder = EM28XX_TVP5150,
.input = { {
.type = EM28XX_VMUX_TELEVISION,
.vmux = TVP5150_SVIDEO,
.amux = 1,
} },
-
- /* gpio's 4, 1, 0 */
- .analog_gpio = 0x003d2d,
},
[EM2880_BOARD_TERRATEC_HYBRID_XS] = {
.name = "Terratec Hybrid XS",
.name = "Kworld USB2800",
.is_em2800 = 1,
.vchannels = 3,
- .tuner_type = TUNER_PHILIPS_ATSC,
+ .tuner_type = TUNER_PHILIPS_FCV1236D,
.tda9887_conf = TDA9887_PRESENT,
.decoder = EM28XX_SAA7113,
.input = { {
.input = { {
.type = EM28XX_VMUX_TELEVISION,
.vmux = SAA7115_COMPOSITE2,
- .amux = 1,
+ .amux = EM28XX_AMUX_LINE_IN,
}, {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = SAA7115_COMPOSITE0,
- .amux = 1,
+ .amux = EM28XX_AMUX_LINE_IN,
}, {
.type = EM28XX_VMUX_SVIDEO,
.vmux = SAA7115_SVIDEO3,
- .amux = 1,
+ .amux = EM28XX_AMUX_LINE_IN,
} },
},
};
.driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
{ USB_DEVICE(0x2040, 0x6500),
.driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900 },
+ { USB_DEVICE(0x2040, 0x6502),
+ .driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900 },
{ USB_DEVICE(0x2040, 0x6513),
.driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_950 },
{ USB_DEVICE(0x0ccd, 0x0042),
};
MODULE_DEVICE_TABLE(usb, em28xx_id_table);
-/* EEPROM hash table for devices with generic USB IDs */
+/*
+ * Reset sequences for analog/digital modes
+ */
+
+/* Board Hauppauge WinTV HVR 900 analog */
+static struct em28xx_reg_seq hauppauge_wintv_hvr_900_analog[] = {
+ {EM28XX_R08_GPIO, 0x2d, ~EM_GPIO_4, 10},
+ {0x05, 0xff, 0x10, 10},
+ { -1, -1, -1, -1},
+};
+
+/* Board Hauppauge WinTV HVR 900 digital */
+static struct em28xx_reg_seq hauppauge_wintv_hvr_900_digital[] = {
+ {EM28XX_R08_GPIO, 0x2e, ~EM_GPIO_4, 10},
+ {EM2880_R04_GPO, 0x04, 0x0f, 10},
+ {EM2880_R04_GPO, 0x0c, 0x0f, 10},
+ { -1, -1, -1, -1},
+};
+
+/* Board Hauppauge WinTV HVR 900 tuner_callback */
+static struct em28xx_reg_seq hauppauge_wintv_hvr_900_tuner_callback[] = {
+ {EM28XX_R08_GPIO, EM_GPIO_4, EM_GPIO_4, 10},
+ {EM28XX_R08_GPIO, 0, EM_GPIO_4, 10},
+ {EM28XX_R08_GPIO, EM_GPIO_4, EM_GPIO_4, 10},
+ { -1, -1, -1, -1},
+};
+
+/*
+ * EEPROM hash table for devices with generic USB IDs
+ */
static struct em28xx_hash_table em28xx_eeprom_hash [] = {
/* P/N: SA 60002070465 Tuner: TVF7533-MF */
{0x6ce05a8f, EM2820_BOARD_PROLINK_PLAYTV_USB2, TUNER_YMEC_TVF_5533MF},
{0xf51200e3, EM2800_BOARD_VGEAR_POCKETTV, TUNER_LG_PAL_NEW_TAPC},
};
+int em28xx_tuner_callback(void *ptr, int command, int arg)
+{
+ int rc = 0;
+ struct em28xx *dev = ptr;
+
+ if (dev->tuner_type != TUNER_XC2028)
+ return 0;
+
+ if (command != XC2028_TUNER_RESET)
+ return 0;
+
+ if (dev->mode == EM28XX_ANALOG_MODE)
+ rc = em28xx_gpio_set(dev, dev->tun_analog_gpio);
+ else
+ rc = em28xx_gpio_set(dev, dev->tun_digital_gpio);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(em28xx_tuner_callback);
+
+static void em28xx_set_model(struct em28xx *dev)
+{
+ dev->is_em2800 = em28xx_boards[dev->model].is_em2800;
+ dev->has_msp34xx = em28xx_boards[dev->model].has_msp34xx;
+ dev->tda9887_conf = em28xx_boards[dev->model].tda9887_conf;
+ dev->decoder = em28xx_boards[dev->model].decoder;
+ dev->video_inputs = em28xx_boards[dev->model].vchannels;
+ dev->has_12mhz_i2s = em28xx_boards[dev->model].has_12mhz_i2s;
+ dev->max_range_640_480 = em28xx_boards[dev->model].max_range_640_480;
+ dev->has_dvb = em28xx_boards[dev->model].has_dvb;
+}
+
/* Since em28xx_pre_card_setup() requires a proper dev->model,
* this won't work for boards with generic PCI IDs
*/
void em28xx_pre_card_setup(struct em28xx *dev)
{
+ int rc;
+
+ rc = em28xx_read_reg(dev, EM2880_R04_GPO);
+ if (rc >= 0)
+ dev->reg_gpo = rc;
+
+ dev->wait_after_write = 5;
+ rc = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
+ if (rc > 0) {
+ switch (rc) {
+ case CHIP_ID_EM2883:
+ em28xx_info("chip ID is em2882/em2883\n");
+ dev->wait_after_write = 0;
+ break;
+ default:
+ em28xx_info("em28xx chip ID = %d\n", rc);
+ }
+ }
+ em28xx_set_model(dev);
+
/* request some modules */
switch (dev->model) {
case EM2880_BOARD_TERRATEC_PRODIGY_XS:
case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
- case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_950:
case EM2880_BOARD_TERRATEC_HYBRID_XS:
- em28xx_write_regs(dev, XCLK_REG, "\x27", 1);
- em28xx_write_regs(dev, I2C_CLK_REG, "\x40", 1);
- em28xx_write_regs(dev, 0x08, "\xff", 1);
- em28xx_write_regs(dev, 0x04, "\x00", 1);
- msleep(100);
- em28xx_write_regs(dev, 0x04, "\x08", 1);
- msleep(100);
- em28xx_write_regs(dev, 0x08, "\xff", 1);
- msleep(50);
- em28xx_write_regs(dev, 0x08, "\x2d", 1);
+ case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_950:
+ em28xx_write_regs(dev, EM28XX_R0F_XCLK, "\x27", 1);
+ em28xx_write_regs(dev, EM28XX_R06_I2C_CLK, "\x40", 1);
msleep(50);
- em28xx_write_regs(dev, 0x08, "\x3d", 1);
+
+ /* Sets GPO/GPIO sequences for this device */
+ dev->analog_gpio = hauppauge_wintv_hvr_900_analog;
+ dev->digital_gpio = hauppauge_wintv_hvr_900_digital;
+ dev->tun_analog_gpio = hauppauge_wintv_hvr_900_tuner_callback;
+ dev->tun_digital_gpio = hauppauge_wintv_hvr_900_tuner_callback;
+
break;
}
+
+ em28xx_gpio_set(dev, dev->tun_analog_gpio);
+ em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
+
+ /* Unlock device */
+ em28xx_set_mode(dev, EM28XX_MODE_UNDEFINED);
}
-static int em28xx_tuner_callback(void *ptr, int command, int arg)
+static void em28xx_setup_xc3028(struct em28xx *dev, struct xc2028_ctrl *ctl)
{
- int rc = 0;
- struct em28xx *dev = ptr;
+ memset(ctl, 0, sizeof(*ctl));
- if (dev->tuner_type != TUNER_XC2028)
- return 0;
-
- switch (command) {
- case XC2028_TUNER_RESET:
- {
- /* GPIO and initialization codes for analog TV and radio
- This code should be complemented for DTV, since reset
- codes are different.
- */
-
- dev->em28xx_write_regs_req(dev, 0x00, 0x48, "\x00", 1);
- dev->em28xx_write_regs_req(dev, 0x00, 0x12, "\x67", 1);
-
- if (dev->analog_gpio) {
- char gpio0 = dev->analog_gpio & 0xff;
- char gpio1 = (dev->analog_gpio >> 8) & 0xff;
- char gpio4 = dev->analog_gpio >> 24;
-
- if (gpio4) {
- dev->em28xx_write_regs(dev, 0x04, &gpio4, 1);
- msleep(140);
- }
-
- msleep(6);
- dev->em28xx_write_regs(dev, 0x08, &gpio0, 1);
- msleep(10);
- dev->em28xx_write_regs(dev, 0x08, &gpio1, 1);
- msleep(5);
- }
+ ctl->fname = XC2028_DEFAULT_FIRMWARE;
+ ctl->max_len = 64;
+ ctl->mts = em28xx_boards[dev->model].mts_firmware;
+ switch (dev->model) {
+ case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
+ ctl->demod = XC3028_FE_ZARLINK456;
break;
+ case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_950:
+ /* FIXME: Better to specify the needed IF */
+ ctl->demod = XC3028_FE_DEFAULT;
+ break;
+ default:
+ ctl->demod = XC3028_FE_OREN538;
}
- }
- return rc;
}
static void em28xx_config_tuner(struct em28xx *dev)
{
struct v4l2_priv_tun_config xc2028_cfg;
- struct xc2028_ctrl ctl;
struct tuner_setup tun_setup;
struct v4l2_frequency f;
em28xx_i2c_call_clients(dev, TUNER_SET_TYPE_ADDR, &tun_setup);
if (dev->tuner_type == TUNER_XC2028) {
- memset(&ctl, 0, sizeof(ctl));
+ struct xc2028_ctrl ctl;
- ctl.fname = XC2028_DEFAULT_FIRMWARE;
- ctl.max_len = 64;
- ctl.mts = em28xx_boards[dev->model].mts_firmware;
+ em28xx_setup_xc3028(dev, &ctl);
xc2028_cfg.tuner = TUNER_XC2028;
xc2028_cfg.priv = &ctl;
return -1;
}
-
-static void em28xx_set_model(struct em28xx *dev)
-{
- dev->is_em2800 = em28xx_boards[dev->model].is_em2800;
- dev->has_msp34xx = em28xx_boards[dev->model].has_msp34xx;
- dev->tda9887_conf = em28xx_boards[dev->model].tda9887_conf;
- dev->decoder = em28xx_boards[dev->model].decoder;
- dev->video_inputs = em28xx_boards[dev->model].vchannels;
- dev->analog_gpio = em28xx_boards[dev->model].analog_gpio;
- dev->has_12mhz_i2s = em28xx_boards[dev->model].has_12mhz_i2s;
- dev->max_range_640_480 = em28xx_boards[dev->model].max_range_640_480;
-}
-
/* ----------------------------------------------------------------------- */
void em28xx_set_ir(struct em28xx *dev, struct IR_i2c *ir)
{
projects / mirror_ubuntu-zesty-kernel.git / blobdiff