* @periodic: Set if this is a periodic ep, such as Interrupt
* @isochronous: Set if this is a isochronous ep
* @send_zlp: Set if we need to send a zero-length packet.
+ * @desc_list_dma: The DMA address of descriptor chain currently in use.
+ * @desc_list: Pointer to descriptor DMA chain head currently in use.
+ * @desc_count: Count of entries within the DMA descriptor chain of EP.
+ * @isoc_chain_num: Number of ISOC chain currently in use - either 0 or 1.
+ * @next_desc: index of next free descriptor in the ISOC chain under SW control.
* @total_data: The total number of data bytes done.
* @fifo_size: The size of the FIFO (for periodic IN endpoints)
* @fifo_load: The amount of data loaded into the FIFO (periodic IN)
#define TARGET_FRAME_INITIAL 0xFFFFFFFF
bool frame_overrun;
+ dma_addr_t desc_list_dma;
+ struct dwc2_dma_desc *desc_list;
+ u8 desc_count;
+
+ unsigned char isoc_chain_num;
+ unsigned int next_desc;
+
char name[10];
};
DWC2_L3, /* Off state */
};
+/*
+ * Gadget periodic tx fifo sizes as used by legacy driver
+ * EP0 is not included
+ */
+#define DWC2_G_P_LEGACY_TX_FIFO_SIZE {256, 256, 256, 256, 768, 768, 768, \
+ 768, 0, 0, 0, 0, 0, 0, 0}
+
/* Gadget ep0 states */
enum dwc2_ep0_state {
DWC2_EP0_SETUP,
* @otg_ver: OTG version supported
* 0 - 1.3 (default)
* 1 - 2.0
- * @dma_enable: Specifies whether to use slave or DMA mode for accessing
+ * @host_dma: Specifies whether to use slave or DMA mode for accessing
* the data FIFOs. The driver will automatically detect the
* value for this parameter if none is specified.
* 0 - Slave (always available)
* @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters
* 1 - Allow dynamic FIFO sizing (default, if available)
* @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs
- * are enabled
+ * are enabled for non-periodic IN endpoints in device
+ * mode.
* @host_rx_fifo_size: Number of 4-byte words in the Rx FIFO in host mode when
* dynamic FIFO sizing is enabled
* 16 to 32768
* needed.
* 0 - No (default)
* 1 - Yes
+ * @g_dma: Enables gadget dma usage (default: autodetect).
+ * @g_dma_desc: Enables gadget descriptor DMA (default: autodetect).
+ * @g_rx_fifo_size: The periodic rx fifo size for the device, in
+ * DWORDS from 16-32768 (default: 2048 if
+ * possible, otherwise autodetect).
+ * @g_np_tx_fifo_size: The non-periodic tx fifo size for the device in
+ * DWORDS from 16-32768 (default: 1024 if
+ * possible, otherwise autodetect).
+ * @g_tx_fifo_size: An array of TX fifo sizes in dedicated fifo
+ * mode. Each value corresponds to one EP
+ * starting from EP1 (max 15 values). Sizes are
+ * in DWORDS with possible values from from
+ * 16-32768 (default: 256, 256, 256, 256, 768,
+ * 768, 768, 768, 0, 0, 0, 0, 0, 0, 0).
*
* The following parameters may be specified when starting the module. These
* parameters define how the DWC_otg controller should be configured. A
* dwc2_set_all_params!
*/
int otg_cap;
+#define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0
+#define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1
+#define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2
+
int otg_ver;
- int dma_enable;
int dma_desc_enable;
int dma_desc_fs_enable;
int speed;
+#define DWC2_SPEED_PARAM_HIGH 0
+#define DWC2_SPEED_PARAM_FULL 1
+#define DWC2_SPEED_PARAM_LOW 2
+
int enable_dynamic_fifo;
int en_multiple_tx_fifo;
int host_rx_fifo_size;
int max_packet_count;
int host_channels;
int phy_type;
+#define DWC2_PHY_TYPE_PARAM_FS 0
+#define DWC2_PHY_TYPE_PARAM_UTMI 1
+#define DWC2_PHY_TYPE_PARAM_ULPI 2
+
int phy_utmi_width;
int phy_ulpi_ddr;
int phy_ulpi_ext_vbus;
+#define DWC2_PHY_ULPI_INTERNAL_VBUS 0
+#define DWC2_PHY_ULPI_EXTERNAL_VBUS 1
+
int i2c_enable;
int ulpi_fs_ls;
int host_support_fs_ls_low_power;
int host_ls_low_power_phy_clk;
+#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0
+#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1
+
int ts_dline;
int reload_ctl;
int ahbcfg;
int uframe_sched;
int external_id_pin_ctl;
int hibernation;
+
+ /*
+ * The following parameters are *only* set via device
+ * properties and cannot be set directly in this structure.
+ */
+
+ /* Host parameters */
+ bool host_dma;
+
+ /* Gadget parameters */
+ bool g_dma;
+ bool g_dma_desc;
+ u16 g_rx_fifo_size;
+ u16 g_np_tx_fifo_size;
+ u32 g_tx_fifo_size[MAX_EPS_CHANNELS];
};
/**
unsigned op_mode:3;
unsigned arch:2;
unsigned dma_desc_enable:1;
- unsigned dma_desc_fs_enable:1;
unsigned enable_dynamic_fifo:1;
unsigned en_multiple_tx_fifo:1;
- unsigned host_rx_fifo_size:16;
+ unsigned rx_fifo_size:16;
unsigned host_nperio_tx_fifo_size:16;
unsigned dev_nperio_tx_fifo_size:16;
unsigned host_perio_tx_fifo_size:16;
* @ctrl_req: Request for EP0 control packets.
* @ep0_state: EP0 control transfers state
* @test_mode: USB test mode requested by the host
+ * @setup_desc_dma: EP0 setup stage desc chain DMA address
+ * @setup_desc: EP0 setup stage desc chain pointer
+ * @ctrl_in_desc_dma: EP0 IN data phase desc chain DMA address
+ * @ctrl_in_desc: EP0 IN data phase desc chain pointer
+ * @ctrl_out_desc_dma: EP0 OUT data phase desc chain DMA address
+ * @ctrl_out_desc: EP0 OUT data phase desc chain pointer
* @eps: The endpoints being supplied to the gadget framework
- * @g_using_dma: Indicate if dma usage is enabled
- * @g_rx_fifo_sz: Contains rx fifo size value
- * @g_np_g_tx_fifo_sz: Contains Non-Periodic tx fifo size value
- * @g_tx_fifo_sz: Contains tx fifo size value per endpoints
*/
struct dwc2_hsotg {
struct device *dev;
/** Params detected from hardware */
struct dwc2_hw_params hw_params;
/** Params to actually use */
- struct dwc2_core_params *core_params;
+ struct dwc2_core_params params;
enum usb_otg_state op_state;
enum usb_dr_mode dr_mode;
unsigned int hcd_enabled:1;
#define DWC2_CORE_REV_2_94a 0x4f54294a
#define DWC2_CORE_REV_3_00a 0x4f54300a
#define DWC2_CORE_REV_3_10a 0x4f54310a
+#define DWC2_FS_IOT_REV_1_00a 0x5531100a
+#define DWC2_HS_IOT_REV_1_00a 0x5532100a
#if IS_ENABLED(CONFIG_USB_DWC2_HOST) || IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)
union dwc2_hcd_internal_flags {
enum dwc2_ep0_state ep0_state;
u8 test_mode;
+ dma_addr_t setup_desc_dma[2];
+ struct dwc2_dma_desc *setup_desc[2];
+ dma_addr_t ctrl_in_desc_dma;
+ struct dwc2_dma_desc *ctrl_in_desc;
+ dma_addr_t ctrl_out_desc_dma;
+ struct dwc2_dma_desc *ctrl_out_desc;
+
struct usb_gadget gadget;
unsigned int enabled:1;
unsigned int connected:1;
struct dwc2_hsotg_ep *eps_in[MAX_EPS_CHANNELS];
struct dwc2_hsotg_ep *eps_out[MAX_EPS_CHANNELS];
- u32 g_using_dma;
- u32 g_rx_fifo_sz;
- u32 g_np_g_tx_fifo_sz;
- u32 g_tx_fifo_sz[MAX_EPS_CHANNELS];
#endif /* CONFIG_USB_DWC2_PERIPHERAL || CONFIG_USB_DWC2_DUAL_ROLE */
};
DWC2_HC_XFER_URB_DEQUEUE,
};
+/* Core version information */
+static inline bool dwc2_is_iot(struct dwc2_hsotg *hsotg)
+{
+ return (hsotg->hw_params.snpsid & 0xfff00000) == 0x55300000;
+}
+
+static inline bool dwc2_is_fs_iot(struct dwc2_hsotg *hsotg)
+{
+ return (hsotg->hw_params.snpsid & 0xffff0000) == 0x55310000;
+}
+
+static inline bool dwc2_is_hs_iot(struct dwc2_hsotg *hsotg)
+{
+ return (hsotg->hw_params.snpsid & 0xffff0000) == 0x55320000;
+}
+
/*
* The following functions support initialization of the core driver component
* and the DWC_otg controller
extern int dwc2_enter_hibernation(struct dwc2_hsotg *hsotg);
extern int dwc2_exit_hibernation(struct dwc2_hsotg *hsotg, bool restore);
+bool dwc2_force_mode_if_needed(struct dwc2_hsotg *hsotg, bool host);
+void dwc2_clear_force_mode(struct dwc2_hsotg *hsotg);
void dwc2_force_dr_mode(struct dwc2_hsotg *hsotg);
extern bool dwc2_is_controller_alive(struct dwc2_hsotg *hsotg);
/* This function should be called on every hardware interrupt. */
extern irqreturn_t dwc2_handle_common_intr(int irq, void *dev);
-/* OTG Core Parameters */
-
-/*
- * Specifies the OTG capabilities. The driver will automatically
- * detect the value for this parameter if none is specified.
- * 0 - HNP and SRP capable (default)
- * 1 - SRP Only capable
- * 2 - No HNP/SRP capable
- */
-extern void dwc2_set_param_otg_cap(struct dwc2_hsotg *hsotg, int val);
-#define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0
-#define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1
-#define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2
-
-/*
- * Specifies whether to use slave or DMA mode for accessing the data
- * FIFOs. The driver will automatically detect the value for this
- * parameter if none is specified.
- * 0 - Slave
- * 1 - DMA (default, if available)
- */
-extern void dwc2_set_param_dma_enable(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * When DMA mode is enabled specifies whether to use
- * address DMA or DMA Descritor mode for accessing the data
- * FIFOs in device mode. The driver will automatically detect
- * the value for this parameter if none is specified.
- * 0 - address DMA
- * 1 - DMA Descriptor(default, if available)
- */
-extern void dwc2_set_param_dma_desc_enable(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * When DMA mode is enabled specifies whether to use
- * address DMA or DMA Descritor mode with full speed devices
- * for accessing the data FIFOs in host mode.
- * 0 - address DMA
- * 1 - FS DMA Descriptor(default, if available)
- */
-extern void dwc2_set_param_dma_desc_fs_enable(struct dwc2_hsotg *hsotg,
- int val);
-
-/*
- * Specifies the maximum speed of operation in host and device mode.
- * The actual speed depends on the speed of the attached device and
- * the value of phy_type. The actual speed depends on the speed of the
- * attached device.
- * 0 - High Speed (default)
- * 1 - Full Speed
- */
-extern void dwc2_set_param_speed(struct dwc2_hsotg *hsotg, int val);
-#define DWC2_SPEED_PARAM_HIGH 0
-#define DWC2_SPEED_PARAM_FULL 1
-
-/*
- * Specifies whether low power mode is supported when attached
- * to a Full Speed or Low Speed device in host mode.
- *
- * 0 - Don't support low power mode (default)
- * 1 - Support low power mode
- */
-extern void dwc2_set_param_host_support_fs_ls_low_power(
- struct dwc2_hsotg *hsotg, int val);
-
-/*
- * Specifies the PHY clock rate in low power mode when connected to a
- * Low Speed device in host mode. This parameter is applicable only if
- * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS
- * then defaults to 6 MHZ otherwise 48 MHZ.
- *
- * 0 - 48 MHz
- * 1 - 6 MHz
- */
-extern void dwc2_set_param_host_ls_low_power_phy_clk(struct dwc2_hsotg *hsotg,
- int val);
-#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0
-#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1
-
-/*
- * 0 - Use cC FIFO size parameters
- * 1 - Allow dynamic FIFO sizing (default)
- */
-extern void dwc2_set_param_enable_dynamic_fifo(struct dwc2_hsotg *hsotg,
- int val);
-
-/*
- * Number of 4-byte words in the Rx FIFO in host mode when dynamic
- * FIFO sizing is enabled.
- * 16 to 32768 (default 1024)
- */
-extern void dwc2_set_param_host_rx_fifo_size(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * Number of 4-byte words in the non-periodic Tx FIFO in host mode
- * when Dynamic FIFO sizing is enabled in the core.
- * 16 to 32768 (default 256)
- */
-extern void dwc2_set_param_host_nperio_tx_fifo_size(struct dwc2_hsotg *hsotg,
- int val);
-
-/*
- * Number of 4-byte words in the host periodic Tx FIFO when dynamic
- * FIFO sizing is enabled.
- * 16 to 32768 (default 256)
- */
-extern void dwc2_set_param_host_perio_tx_fifo_size(struct dwc2_hsotg *hsotg,
- int val);
-
-/*
- * The maximum transfer size supported in bytes.
- * 2047 to 65,535 (default 65,535)
- */
-extern void dwc2_set_param_max_transfer_size(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * The maximum number of packets in a transfer.
- * 15 to 511 (default 511)
- */
-extern void dwc2_set_param_max_packet_count(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * The number of host channel registers to use.
- * 1 to 16 (default 11)
- * Note: The FPGA configuration supports a maximum of 11 host channels.
- */
-extern void dwc2_set_param_host_channels(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * Specifies the type of PHY interface to use. By default, the driver
- * will automatically detect the phy_type.
- *
- * 0 - Full Speed PHY
- * 1 - UTMI+ (default)
- * 2 - ULPI
- */
-extern void dwc2_set_param_phy_type(struct dwc2_hsotg *hsotg, int val);
-#define DWC2_PHY_TYPE_PARAM_FS 0
-#define DWC2_PHY_TYPE_PARAM_UTMI 1
-#define DWC2_PHY_TYPE_PARAM_ULPI 2
-
-/*
- * Specifies the UTMI+ Data Width. This parameter is
- * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI
- * PHY_TYPE, this parameter indicates the data width between
- * the MAC and the ULPI Wrapper.) Also, this parameter is
- * applicable only if the OTG_HSPHY_WIDTH cC parameter was set
- * to "8 and 16 bits", meaning that the core has been
- * configured to work at either data path width.
- *
- * 8 or 16 bits (default 16)
- */
-extern void dwc2_set_param_phy_utmi_width(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * Specifies whether the ULPI operates at double or single
- * data rate. This parameter is only applicable if PHY_TYPE is
- * ULPI.
- *
- * 0 - single data rate ULPI interface with 8 bit wide data
- * bus (default)
- * 1 - double data rate ULPI interface with 4 bit wide data
- * bus
- */
-extern void dwc2_set_param_phy_ulpi_ddr(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * Specifies whether to use the internal or external supply to
- * drive the vbus with a ULPI phy.
- */
-extern void dwc2_set_param_phy_ulpi_ext_vbus(struct dwc2_hsotg *hsotg, int val);
-#define DWC2_PHY_ULPI_INTERNAL_VBUS 0
-#define DWC2_PHY_ULPI_EXTERNAL_VBUS 1
-
-/*
- * Specifies whether to use the I2Cinterface for full speed PHY. This
- * parameter is only applicable if PHY_TYPE is FS.
- * 0 - No (default)
- * 1 - Yes
- */
-extern void dwc2_set_param_i2c_enable(struct dwc2_hsotg *hsotg, int val);
-
-extern void dwc2_set_param_ulpi_fs_ls(struct dwc2_hsotg *hsotg, int val);
-
-extern void dwc2_set_param_ts_dline(struct dwc2_hsotg *hsotg, int val);
-
-/*
- * Specifies whether dedicated transmit FIFOs are
- * enabled for non periodic IN endpoints in device mode
- * 0 - No
- * 1 - Yes
- */
-extern void dwc2_set_param_en_multiple_tx_fifo(struct dwc2_hsotg *hsotg,
- int val);
-
-extern void dwc2_set_param_reload_ctl(struct dwc2_hsotg *hsotg, int val);
-
-extern void dwc2_set_param_ahbcfg(struct dwc2_hsotg *hsotg, int val);
-
-extern void dwc2_set_param_otg_ver(struct dwc2_hsotg *hsotg, int val);
-
-extern void dwc2_set_parameters(struct dwc2_hsotg *hsotg,
- const struct dwc2_core_params *params);
-
-extern void dwc2_set_all_params(struct dwc2_core_params *params, int value);
-
-extern int dwc2_get_hwparams(struct dwc2_hsotg *hsotg);
+/* The device ID match table */
+extern const struct of_device_id dwc2_of_match_table[];
extern int dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg);
extern int dwc2_lowlevel_hw_disable(struct dwc2_hsotg *hsotg);
+/* Parameters */
+int dwc2_get_hwparams(struct dwc2_hsotg *hsotg);
+int dwc2_init_params(struct dwc2_hsotg *hsotg);
+
/*
* The following functions check the controller's OTG operation mode
* capability (GHWCFG2.OTG_MODE).
projects / mirror_ubuntu-bionic-kernel.git / blobdiff