menu "Graphics support"
depends on HAS_IOMEM
+config HAVE_FB_ATMEL
+ bool
+
source "drivers/char/agp/Kconfig"
+source "drivers/gpu/vga/Kconfig"
+
source "drivers/gpu/drm/Kconfig"
config VGASTATE
config FB_ATMEL
tristate "AT91/AT32 LCD Controller support"
- depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || AVR32)
+ depends on FB && HAVE_FB_ATMEL
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
config FB_ATMEL_STN
bool "Use a STN display with AT91/AT32 LCD Controller"
- depends on FB_ATMEL && MACH_AT91SAM9261EK
+ depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
default n
help
Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
painting procedures (the secondary head does not use acceleration
engine).
-config FB_MATROX_MULTIHEAD
- bool "Multihead support"
- depends on FB_MATROX
- ---help---
- Say Y here if you have more than one (supported) Matrox device in
- your computer and you want to use all of them for different monitors
- ("multihead"). If you have only one device, you should say N because
- the driver compiled with Y is larger and a bit slower, especially on
- ia32 (ix86).
-
- If you said M to "Matrox unified accelerated driver" and N here, you
- will still be able to use several Matrox devices simultaneously:
- insert several instances of the module matroxfb into the kernel
- with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
- for the different Matrox devices. This method is slightly faster but
- uses 40 KB of kernel memory per Matrox card.
-
- There is no need for enabling 'Matrox multihead support' if you have
- only one Matrox card in the box.
-
config FB_RADEON
tristate "ATI Radeon display support"
depends on FB && PCI
config FB_SH_MOBILE_LCDC
tristate "SuperH Mobile LCDC framebuffer support"
- depends on FB && SUPERH
+ depends on FB && SUPERH && HAVE_CLK
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
panels <= 320 pixel horizontal resolution.
+config FB_DA8XX
+ tristate "DA8xx/OMAP-L1xx Framebuffer support"
+ depends on FB && ARCH_DAVINCI_DA8XX
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ ---help---
+ This is the frame buffer device driver for the TI LCD controller
+ found on DA8xx/OMAP-L1xx SoCs.
+ If unsure, say N.
+
config FB_VIRTUAL
tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
depends on FB
---help---
Framebuffer support for Fujitsu Lime GDC on host CPU bus.
+config FB_EP93XX
+ tristate "EP93XX frame buffer support"
+ depends on FB && ARCH_EP93XX
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ ---help---
+ Framebuffer driver for the Cirrus Logic EP93XX series of processors.
+ This driver is also available as a module. The module will be called
+ ep93xx-fb.
+
config FB_PRE_INIT_FB
bool "Don't reinitialize, use bootloader's GDC/Display configuration"
- depends on FB_MB862XX_LIME
+ depends on FB && FB_MB862XX_LIME
---help---
Select this option if display contents should be inherited as set by
the bootloader.
+config FB_MSM
+ tristate
+ depends on FB && ARCH_MSM
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ default y
+
config FB_MX3
tristate "MX3 Framebuffer support"
depends on FB && MX3_IPU