status &= 0xffffffd7;
- if (status) {
- /* Handle the TXDMA Error interrupt */
- if (status & ET_INTR_TXDMA_ERR) {
- u32 txdma_err;
+ if (!status)
+ goto out;
- /* Following read also clears the register (COR) */
- txdma_err = readl(&iomem->txdma.tx_dma_error);
+ /* Handle the TXDMA Error interrupt */
+ if (status & ET_INTR_TXDMA_ERR) {
+ u32 txdma_err;
- dev_warn(&adapter->pdev->dev,
- "TXDMA_ERR interrupt, error = %d\n",
- txdma_err);
- }
+ /* Following read also clears the register (COR) */
+ txdma_err = readl(&iomem->txdma.tx_dma_error);
- /* Handle Free Buffer Ring 0 and 1 Low interrupt */
- if (status &
- (ET_INTR_RXDMA_FB_R0_LOW | ET_INTR_RXDMA_FB_R1_LOW)) {
- /*
- * This indicates the number of unused buffers in
- * RXDMA free buffer ring 0 is <= the limit you
- * programmed. Free buffer resources need to be
- * returned. Free buffers are consumed as packets
- * are passed from the network to the host. The host
- * becomes aware of the packets from the contents of
- * the packet status ring. This ring is queried when
- * the packet done interrupt occurs. Packets are then
- * passed to the OS. When the OS is done with the
- * packets the resources can be returned to the
- * ET1310 for re-use. This interrupt is one method of
- * returning resources.
- */
-
- /* If the user has flow control on, then we will
- * send a pause packet, otherwise just exit
- */
- if (adapter->flowcontrol == FLOW_TXONLY ||
- adapter->flowcontrol == FLOW_BOTH) {
- u32 pm_csr;
+ dev_warn(&adapter->pdev->dev,
+ "TXDMA_ERR interrupt, error = %d\n",
+ txdma_err);
+ }
- /* Tell the device to send a pause packet via
- * the back pressure register (bp req and
- * bp xon/xoff)
- */
- pm_csr = readl(&iomem->global.pm_csr);
- if (!et1310_in_phy_coma(adapter))
- writel(3, &iomem->txmac.bp_ctrl);
- }
- }
+ /* Handle Free Buffer Ring 0 and 1 Low interrupt */
+ if (status & (ET_INTR_RXDMA_FB_R0_LOW | ET_INTR_RXDMA_FB_R1_LOW)) {
+ /*
+ * This indicates the number of unused buffers in RXDMA free
+ * buffer ring 0 is <= the limit you programmed. Free buffer
+ * resources need to be returned. Free buffers are consumed as
+ * packets are passed from the network to the host. The host
+ * becomes aware of the packets from the contents of the packet
+ * status ring. This ring is queried when the packet done
+ * interrupt occurs. Packets are then passed to the OS. When
+ * the OS is done with the packets the resources can be
+ * returned to the ET1310 for re-use. This interrupt is one
+ * method of returning resources.
+ */
- /* Handle Packet Status Ring Low Interrupt */
- if (status & ET_INTR_RXDMA_STAT_LOW) {
+ /*
+ * If the user has flow control on, then we will
+ * send a pause packet, otherwise just exit
+ */
+ if (adapter->flowcontrol == FLOW_TXONLY ||
+ adapter->flowcontrol == FLOW_BOTH) {
+ u32 pm_csr;
/*
- * Same idea as with the two Free Buffer Rings.
- * Packets going from the network to the host each
- * consume a free buffer resource and a packet status
- * resource. These resoures are passed to the OS.
- * When the OS is done with the resources, they need
- * to be returned to the ET1310. This is one method
- * of returning the resources.
+ * Tell the device to send a pause packet via the back
+ * pressure register (bp req and bp xon/xoff)
*/
+ pm_csr = readl(&iomem->global.pm_csr);
+ if (!et1310_in_phy_coma(adapter))
+ writel(3, &iomem->txmac.bp_ctrl);
}
+ }
- /* Handle RXDMA Error Interrupt */
- if (status & ET_INTR_RXDMA_ERR) {
- /*
- * The rxdma_error interrupt is sent when a time-out
- * on a request issued by the JAGCore has occurred or
- * a completion is returned with an un-successful
- * status. In both cases the request is considered
- * complete. The JAGCore will automatically re-try the
- * request in question. Normally information on events
- * like these are sent to the host using the "Advanced
- * Error Reporting" capability. This interrupt is
- * another way of getting similar information. The
- * only thing required is to clear the interrupt by
- * reading the ISR in the global resources. The
- * JAGCore will do a re-try on the request. Normally
- * you should never see this interrupt. If you start
- * to see this interrupt occurring frequently then
- * something bad has occurred. A reset might be the
- * thing to do.
- */
- /* TRAP();*/
+ /* Handle Packet Status Ring Low Interrupt */
+ if (status & ET_INTR_RXDMA_STAT_LOW) {
+ /*
+ * Same idea as with the two Free Buffer Rings. Packets going
+ * from the network to the host each consume a free buffer
+ * resource and a packet status resource. These resoures are
+ * passed to the OS. When the OS is done with the resources,
+ * they need to be returned to the ET1310. This is one method
+ * of returning the resources.
+ */
+ }
- dev_warn(&adapter->pdev->dev,
- "RxDMA_ERR interrupt, error %x\n",
- readl(&iomem->txmac.tx_test));
- }
+ /* Handle RXDMA Error Interrupt */
+ if (status & ET_INTR_RXDMA_ERR) {
+ /*
+ * The rxdma_error interrupt is sent when a time-out on a
+ * request issued by the JAGCore has occurred or a completion is
+ * returned with an un-successful status. In both cases the
+ * request is considered complete. The JAGCore will
+ * automatically re-try the request in question. Normally
+ * information on events like these are sent to the host using
+ * the "Advanced Error Reporting" capability. This interrupt is
+ * another way of getting similar information. The only thing
+ * required is to clear the interrupt by reading the ISR in the
+ * global resources. The JAGCore will do a re-try on the
+ * request. Normally you should never see this interrupt. If
+ * you start to see this interrupt occurring frequently then
+ * something bad has occurred. A reset might be the thing to do.
+ */
+ /* TRAP();*/
- /* Handle the Wake on LAN Event */
- if (status & ET_INTR_WOL) {
- /*
- * This is a secondary interrupt for wake on LAN.
- * The driver should never see this, if it does,
- * something serious is wrong. We will TRAP the
- * message when we are in DBG mode, otherwise we
- * will ignore it.
- */
- dev_err(&adapter->pdev->dev, "WAKE_ON_LAN interrupt\n");
- }
+ dev_warn(&adapter->pdev->dev,
+ "RxDMA_ERR interrupt, error %x\n",
+ readl(&iomem->txmac.tx_test));
+ }
- /* Let's move on to the TxMac */
- if (status & ET_INTR_TXMAC) {
- u32 err = readl(&iomem->txmac.err);
+ /* Handle the Wake on LAN Event */
+ if (status & ET_INTR_WOL) {
+ /*
+ * This is a secondary interrupt for wake on LAN. The driver
+ * should never see this, if it does, something serious is
+ * wrong. We will TRAP the message when we are in DBG mode,
+ * otherwise we will ignore it.
+ */
+ dev_err(&adapter->pdev->dev, "WAKE_ON_LAN interrupt\n");
+ }
- /*
- * When any of the errors occur and TXMAC generates
- * an interrupt to report these errors, it usually
- * means that TXMAC has detected an error in the data
- * stream retrieved from the on-chip Tx Q. All of
- * these errors are catastrophic and TXMAC won't be
- * able to recover data when these errors occur. In
- * a nutshell, the whole Tx path will have to be reset
- * and re-configured afterwards.
- */
- dev_warn(&adapter->pdev->dev,
- "TXMAC interrupt, error 0x%08x\n",
- err);
+ /* Let's move on to the TxMac */
+ if (status & ET_INTR_TXMAC) {
+ u32 err = readl(&iomem->txmac.err);
- /* If we are debugging, we want to see this error,
- * otherwise we just want the device to be reset and
- * continue
- */
- }
+ /*
+ * When any of the errors occur and TXMAC generates an
+ * interrupt to report these errors, it usually means that
+ * TXMAC has detected an error in the data stream retrieved
+ * from the on-chip Tx Q. All of these errors are catastrophic
+ * and TXMAC won't be able to recover data when these errors
+ * occur. In a nutshell, the whole Tx path will have to be reset
+ * and re-configured afterwards.
+ */
+ dev_warn(&adapter->pdev->dev,
+ "TXMAC interrupt, error 0x%08x\n",
+ err);
- /* Handle RXMAC Interrupt */
- if (status & ET_INTR_RXMAC) {
- /*
- * These interrupts are catastrophic to the device,
- * what we need to do is disable the interrupts and
- * set the flag to cause us to reset so we can solve
- * this issue.
- */
- /* MP_SET_FLAG( adapter,
- fMP_ADAPTER_HARDWARE_ERROR); */
+ /*
+ * If we are debugging, we want to see this error, otherwise we
+ * just want the device to be reset and continue
+ */
+ }
- dev_warn(&adapter->pdev->dev,
- "RXMAC interrupt, error 0x%08x. Requesting reset\n",
- readl(&iomem->rxmac.err_reg));
+ /* Handle RXMAC Interrupt */
+ if (status & ET_INTR_RXMAC) {
+ /*
+ * These interrupts are catastrophic to the device, what we need
+ * to do is disable the interrupts and set the flag to cause us
+ * to reset so we can solve this issue.
+ */
+ /* MP_SET_FLAG( adapter, fMP_ADAPTER_HARDWARE_ERROR); */
- dev_warn(&adapter->pdev->dev,
- "Enable 0x%08x, Diag 0x%08x\n",
- readl(&iomem->rxmac.ctrl),
- readl(&iomem->rxmac.rxq_diag));
+ dev_warn(&adapter->pdev->dev,
+ "RXMAC interrupt, error 0x%08x. Requesting reset\n",
+ readl(&iomem->rxmac.err_reg));
- /*
- * If we are debugging, we want to see this error,
- * otherwise we just want the device to be reset and
- * continue
- */
- }
+ dev_warn(&adapter->pdev->dev,
+ "Enable 0x%08x, Diag 0x%08x\n",
+ readl(&iomem->rxmac.ctrl),
+ readl(&iomem->rxmac.rxq_diag));
- /* Handle MAC_STAT Interrupt */
- if (status & ET_INTR_MAC_STAT) {
- /*
- * This means at least one of the un-masked counters
- * in the MAC_STAT block has rolled over. Use this
- * to maintain the top, software managed bits of the
- * counter(s).
- */
- et1310_handle_macstat_interrupt(adapter);
- }
+ /*
+ * If we are debugging, we want to see this error, otherwise we
+ * just want the device to be reset and continue
+ */
+ }
- /* Handle SLV Timeout Interrupt */
- if (status & ET_INTR_SLV_TIMEOUT) {
- /*
- * This means a timeout has occurred on a read or
- * write request to one of the JAGCore registers. The
- * Global Resources block has terminated the request
- * and on a read request, returned a "fake" value.
- * The most likely reasons are: Bad Address or the
- * addressed module is in a power-down state and
- * can't respond.
- */
- }
+ /* Handle MAC_STAT Interrupt */
+ if (status & ET_INTR_MAC_STAT) {
+ /*
+ * This means at least one of the un-masked counters in the
+ * MAC_STAT block has rolled over. Use this to maintain the top,
+ * software managed bits of the counter(s).
+ */
+ et1310_handle_macstat_interrupt(adapter);
}
+
+ /* Handle SLV Timeout Interrupt */
+ if (status & ET_INTR_SLV_TIMEOUT) {
+ /*
+ * This means a timeout has occurred on a read or write request
+ * to one of the JAGCore registers. The Global Resources block
+ * has terminated the request and on a read request, returned a
+ * "fake" value. The most likely reasons are: Bad Address or the
+ * addressed module is in a power-down state and can't respond.
+ */
+ }
+out:
et131x_enable_interrupts(adapter);
}
projects / mirror_ubuntu-jammy-kernel.git / commitdiff