- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
must be defined for each tsin child node.
- pinctrl-0 : phandle referencing pin configuration for this tsin configuration
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
Required properties (tsin (child) node):
Following properties are require if pin control setting is required
at boot.
- pinctrl-names: A pinctrl state named "default" be defined, using the
- bindings in pinctrl/pinctrl-binding.txt.
+ bindings in pinctrl/pinctrl-bindings.txt.
- pinctrl[0...n]: Properties to contain the phandle that refer to
different nodes of pin control settings. These nodes represents
the pin control setting of state 0 to state n. Each of these
See: Documentation/devicetree/bindings/clock/clock-bindings.txt
- pinctrl-names: A pinctrl state names "default" must be defined.
- pinctrl-0: Phandle referencing pin configuration of the SDHCI controller.
- See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+ See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
Example:
- pinctrl-names: A pinctrl state names "default" must be defined.
- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller.
- See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+ See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
- reg: This must provide the host controller base address and it can also
contain the FlashSS Top register for TX/RX delay used by the driver
--------------------------
Following properties are required if default setting of pins are required
at boot.
-- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>.
+- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
- <pinctrl-binding.txt>.
+ <pinctrl-bindings.txt>.
The pin configurations are defined as child of the pinctrl states node. Each
sub-node have following properties:
--------------------------
Following properties are required if default setting of pins are required
at boot.
-- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>.
+- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
- <pinctrl-binding.txt>.
+ <pinctrl-bindings.txt>.
The pin configurations are defined as child of the pinctrl states node. Each
sub-node have following properties:
--------------------------
Following properties are required if default setting of pins are required
at boot.
-- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>.
+- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
- <pinctrl-binding.txt>.
+ <pinctrl-bindings.txt>.
The pin configurations are defined as child of the pinctrl states node. Each
sub-node have following properties:
See: Documentation/devicetree/bindings/clock/clock-bindings.txt
- pinctrl-names: A pinctrl state names "default" must be defined.
- pinctrl-0: Phandle referencing pin configuration of the UART peripheral.
- See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+ See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
Optional properties:
- cts-gpios: CTS pin for UART
- clocks : Must contain an entry for each name in clock-names
See ../clk/*
- pinctrl-names : Uses "default", can use "sleep" if provided
- See ../pinctrl/pinctrl-binding.txt
+ See ../pinctrl/pinctrl-bindings.txt
Optional properties:
- cs-gpios : List of GPIO chip selects