- AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
+- AM335X phyCORE-AM335x: Development kit
+ compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
+
- OMAP5 EVM : Evaluation Module
compatible = "ti,omap5-evm", "ti,omap5"
am335x-base0033.dtb \
am335x-bone.dtb \
am335x-boneblack.dtb \
+ am335x-boneblack-wireless.dtb \
am335x-bonegreen.dtb \
+ am335x-bonegreen-wireless.dtb \
am335x-chiliboard.dtb \
am335x-cm-t335.dtb \
am335x-evm.dtb \
am335x-lxm.dtb \
am335x-nano.dtb \
am335x-pepper.dtb \
+ am335x-phycore-rdk.dtb \
am335x-shc.dtb \
am335x-sbc-t335.dtb \
am335x-sl50.dtb \
&usb0 {
status = "okay";
dr_mode = "peripheral";
+ interrupts-extended = <&intc 18 &tps 0>;
+ interrupt-names = "mc", "vbus";
};
&usb1 {
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/display/tda998x.h>
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
+ nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
+ >;
+ };
+
+ mcasp0_pins: mcasp0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
+ AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+ AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
+ AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
+ AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+ >;
+ };
+};
+
+&lcdc {
+ status = "okay";
+
+ /* If you want to get 24 bit RGB and 16 BGR mode instead of
+ * current 16 bit RGB and 24 BGR modes, set the propety
+ * below to "crossed" and uncomment the video-ports -property
+ * in tda19988 node.
+ */
+ blue-and-red-wiring = "straight";
+
+ port {
+ lcdc_0: endpoint@0 {
+ remote-endpoint = <&hdmi_0>;
+ };
+ };
+};
+
+&i2c0 {
+ tda19988: tda19988 {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+
+ pinctrl-names = "default", "off";
+ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+ /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
+ /* video-ports = <0x234501>; */
+
+ #sound-dai-cells = <0>;
+ audio-ports = < TDA998x_I2S 0x03>;
+
+ ports {
+ port@0 {
+ hdmi_0: endpoint@0 {
+ remote-endpoint = <&lcdc_0>;
+ };
+ };
+ };
+ };
+};
+
+&rtc {
+ system-power-controller;
+};
+
+&mcasp0 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp0_pins>;
+ status = "okay";
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+/ {
+ clk_mcasp0_fixed: clk_mcasp0_fixed {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24576000>;
+ };
+
+ clk_mcasp0: clk_mcasp0 {
+ #clock-cells = <0>;
+ compatible = "gpio-gate-clock";
+ clocks = <&clk_mcasp0_fixed>;
+ enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "TI BeagleBone Black";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink0_master>;
+ simple-audio-card,frame-master = <&dailink0_master>;
+
+ dailink0_master: simple-audio-card,cpu {
+ sound-dai = <&mcasp0>;
+ clocks = <&clk_mcasp0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&tda19988>;
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Black Wireless";
+ compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio3 9 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */
+ AM33XX_IOPAD(0x914, PIN_INPUT_PULLUP | MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */
+ AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */
+ AM33XX_IOPAD(0x91c, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */
+ AM33XX_IOPAD(0x920, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */
+ AM33XX_IOPAD(0x908, PIN_INPUT_PULLUP | MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */
+ AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */
+ AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio3 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
-#include <dt-bindings/display/tda998x.h>
+#include "am335x-boneblack-common.dtsi"
/ {
model = "TI AM335x BeagleBone Black";
compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
};
-
-&ldo3_reg {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_pins>;
- bus-width = <8>;
- status = "okay";
-};
-
-&am33xx_pinmux {
- nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
- AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
- AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
- AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
- AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
- AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
- AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
- AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
- AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
- AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
- AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
- AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
- AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
- AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
- AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
- AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
- AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
- AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
- AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
- AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
- AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
- >;
- };
- nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr0 */
- >;
- };
-
- mcasp0_pins: mcasp0_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
- AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
- AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
- AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
- AM33XX_IOPAD(0x86c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */
- >;
- };
-};
-
-&lcdc {
- status = "okay";
-
- /* If you want to get 24 bit RGB and 16 BGR mode instead of
- * current 16 bit RGB and 24 BGR modes, set the propety
- * below to "crossed" and uncomment the video-ports -property
- * in tda19988 node.
- */
- blue-and-red-wiring = "straight";
-
- port {
- lcdc_0: endpoint@0 {
- remote-endpoint = <&hdmi_0>;
- };
- };
-};
-
-&i2c0 {
- tda19988: tda19988 {
- compatible = "nxp,tda998x";
- reg = <0x70>;
-
- pinctrl-names = "default", "off";
- pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
- pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
- /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
- /* video-ports = <0x234501>; */
-
- #sound-dai-cells = <0>;
- audio-ports = < TDA998x_I2S 0x03>;
-
- ports {
- port@0 {
- hdmi_0: endpoint@0 {
- remote-endpoint = <&lcdc_0>;
- };
- };
- };
- };
-};
-
-&rtc {
- system-power-controller;
-};
-
-&mcasp0 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mcasp0_pins>;
- status = "okay";
- op-mode = <0>; /* MCASP_IIS_MODE */
- tdm-slots = <2>;
- serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
- 0 0 1 0
- >;
- tx-num-evt = <32>;
- rx-num-evt = <32>;
-};
-
-/ {
- clk_mcasp0_fixed: clk_mcasp0_fixed {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24576000>;
- };
-
- clk_mcasp0: clk_mcasp0 {
- #clock-cells = <0>;
- compatible = "gpio-gate-clock";
- clocks = <&clk_mcasp0_fixed>;
- enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "TI BeagleBone Black";
- simple-audio-card,format = "i2s";
- simple-audio-card,bitclock-master = <&dailink0_master>;
- simple-audio-card,frame-master = <&dailink0_master>;
-
- dailink0_master: simple-audio-card,cpu {
- sound-dai = <&mcasp0>;
- clocks = <&clk_mcasp0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&tda19988>;
- };
- };
-};
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&ldo3_reg {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&am33xx_pinmux {
+ uart2_pins: uart2_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
+ AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
+ >;
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&rtc {
+ system-power-controller;
+};
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "TI AM335x BeagleBone Green Wireless";
+ compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+ wlan_en_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us= <70000>;
+
+ /* WL_EN */
+ gpio = <&gpio0 26 0>;
+ enable-active-high;
+ };
+};
+
+&am33xx_pinmux {
+ bt_pins: pinmux_bt_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_ad12.gpio1_28 BT_EN */
+ >;
+ };
+
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad12.mmc2_dat0 */
+ AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad13.mmc2_dat1 */
+ AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad14.mmc2_dat2 */
+ AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ad15.mmc2_dat3 */
+ AM33XX_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd */
+ AM33XX_IOPAD(0x88c, PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* gmii1_rxd2.uart3_txd */
+ AM33XX_IOPAD(0x948, PIN_INPUT | MUX_MODE3) /* mdio_data.uart3_ctsn */
+ AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* mdio_clk.uart3_rtsn */
+ >;
+ };
+
+ wl18xx_pins: pinmux_wl18xx_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x828, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN */
+ AM33XX_IOPAD(0x82C, PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ */
+ AM33XX_IOPAD(0x87C, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 LS_BUF_EN */
+ >;
+ };
+};
+
+&mac {
+ status = "disabled";
+};
+
+&mmc3 {
+ dmas = <&edma_xbar 12 0 1
+ &edma_xbar 13 0 2>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ ti,needs-special-hs-handling;
+ keep-power-in-suspend;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins &bt_pins>;
+ status = "okay";
+};
+
+&gpio1 {
+ ls_buf_en {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "LS_BUF_EN";
+ };
+};
+
+/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
+/* in case it isn't, wilink8 ends up in one of the test modes that */
+/* intruces various issues (elp wkaeup timeouts etc.) */
+/* On the BBGW this pin is routed through the level shifter (U21) that */
+/* introduces a pullup on the line and wilink8 ends up in a bad state. */
+/* use a gpio hog to force this pin low. An alternative may be adding */
+/* an external pulldown on U21 pin 4. */
+
+&gpio3 {
+ bt_aud_in {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "MCASP0_AHCLKR";
+ };
+};
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
/ {
model = "TI AM335x BeagleBone Green";
compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
};
-
-&ldo3_reg {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmcsd_fixed>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_pins>;
- bus-width = <8>;
- status = "okay";
-};
-
-&am33xx_pinmux {
- uart2_pins: uart2_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
- AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
- >;
- };
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
- status = "okay";
-};
-
-&rtc {
- system-power-controller;
-};
&rtc {
system-power-controller;
+
+ pinctrl-0 = <&ext_wakeup>;
+ pinctrl-names = "default";
+
+ ext_wakeup: ext-wakeup {
+ pins = "ext_wakeup0";
+ input-enable;
+ };
};
/* NAND Flash */
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
vbat: fixedregulator0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
vbat: fixedregulator0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ chosen {
+ stdout-path = &uart3;
+ };
+
vbat: fixedregulator0 {
compatible = "regulator-fixed";
regulator-name = "vbat";
#address-cells = <2>;
#size-cells = <1>;
- ranges = <0 0 0x08000000 0x08000000>; /* CS0: NOR 128M */
+ ranges = <0 0 0x08000000 0x08000000>, /* CS0: NOR 128M */
+ <1 0 0x1c000000 0x01000000>; /* CS1: FRAM 16M */
nor@0,0 {
reg = <0 0x00000000 0x08000000>;
reg = <0x04000000 0x04000000>; /* 64MB */
};
};
+
+ fram@1,0 {
+ reg = <1 0x00000000 0x01000000>;
+ bank-width = <2>;
+
+ gpmc,mux-add-data = <2>;
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <160>;
+ gpmc,cs-wr-off-ns = <160>;
+ gpmc,adv-on-ns = <10>;
+ gpmc,adv-rd-off-ns = <20>;
+ gpmc,adv-wr-off-ns = <20>;
+ gpmc,oe-on-ns = <30>;
+ gpmc,oe-off-ns = <150>;
+ gpmc,we-on-ns = <30>;
+ gpmc,we-off-ns = <150>;
+ gpmc,rd-cycle-ns = <160>;
+ gpmc,wr-cycle-ns = <160>;
+ gpmc,access-ns = <130>;
+ gpmc,page-burst-access-ns = <10>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+ gpmc,cycle2cycle-delay-ns = <10>;
+ gpmc,wr-data-mux-bus-ns = <30>;
+ gpmc,wr-access-ns = <0>;
+ };
};
&mac {
--- /dev/null
+/*
+ * Copyright (C) 2014-2017 Phytec Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ * Teresa Remmet <t.remmet@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Phytec AM335x PCM-953";
+ compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx";
+
+ /* Power */
+ regulators {
+ vcc3v3: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ vcc1v8: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+ };
+
+ /* User IO */
+ user_leds: user_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds_pins>;
+
+ green {
+ label = "green:user";
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+
+ yellow {
+ label = "yellow:user";
+ gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+ };
+
+ user_buttons: user_buttons {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_buttons_pins>;
+
+ button@0 {
+ label = "home";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+
+ button@1 {
+ label = "menu";
+ linux,code = <KEY_MENU>;
+ gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+
+ };
+};
+
+&am33xx_pinmux {
+ user_buttons_pins: pinmux_user_buttons {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* emu0.gpio3_7 */
+ AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* emu1.gpio3_8 */
+ >;
+ };
+
+ user_leds_pins: pinmux_user_leds {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x880, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn1.gpio1_30 */
+ AM33XX_IOPAD(0x884, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn2.gpio1_31 */
+ >;
+ };
+};
+
+/* CAN */
+&am33xx_pinmux {
+ dcan1_pins: pinmux_dcan1 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x980, PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart1_rxd.dcan1_tx_mux2 */
+ AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE2) /* uart1_txd.dcan1_rx_mux2 */
+ >;
+ };
+};
+
+&dcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan1_pins>;
+ status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+ ethernet1_pins: pinmux_ethernet1 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
+ AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
+ AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
+ AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
+ AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
+ AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
+ AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
+ AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
+ AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
+ AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
+ AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
+ AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
+ >;
+ };
+};
+
+&cpsw_emac1 {
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii-id";
+ dual_emac_res_vlan = <2>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ phy1: ethernet-phy@2 {
+ reg = <2>;
+
+ /* Register 260 (104h) – RGMII Clock and Control Pad Skew */
+ rxc-skew-ps = <1400>;
+ rxdv-skew-ps = <0>;
+ txc-skew-ps = <1400>;
+ txen-skew-ps = <0>;
+ /* Register 261 (105h) – RGMII RX Data Pad Skew */
+ rxd3-skew-ps = <0>;
+ rxd2-skew-ps = <0>;
+ rxd1-skew-ps = <0>;
+ rxd0-skew-ps = <0>;
+ /* Register 262 (106h) – RGMII TX Data Pad Skew */
+ txd3-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd0-skew-ps = <0>;
+ };
+};
+
+&mac {
+ slaves = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet0_pins ðernet1_pins>;
+ dual_emac;
+};
+
+/* Misc */
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cb_gpio_pins>;
+
+ cb_gpio_pins: pinmux_cb_gpio {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart0_ctsn.gpio1_8 */
+ AM33XX_IOPAD(0x96c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart0_rtsn.gpio1_9 */
+ >;
+ };
+};
+
+/* MMC */
+&am33xx_pinmux {
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+ AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+ AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+ AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+ AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+ AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+ AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7) /* spi0_cs1.mmc0_sdcd */
+ >;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vcc3v3>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+/* UARTs */
+&am33xx_pinmux {
+ uart0_pins: pinmux_uart0 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
+ AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_tx_clk.uart2_rxd */
+ AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_rx_clk.uart2_txd */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3 {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd2.uart3_txd */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+/* USB */
+&cppi41dma {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb1_phy {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (C) 2014 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am335x-phycore-som.dtsi"
+#include "am335x-pcm-953.dtsi"
+
+/* SoM */
+&i2c_eeprom {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+&serial_flash {
+ status = "okay";
+
+};
};
&cpsw_emac0 {
- phy_id = <&davinci_mdio>, <0>;
+ phy-handle = <&phy0>;
phy-mode = "rmii";
dual_emac_res_vlan = <1>;
};
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>;
status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
};
&mac {
reg = <0x2d>;
};
+ i2c_tmp102: temp@4b {
+ compatible = "ti,tmp102";
+ reg = <0x4b>;
+ status = "disabled";
+ };
+
i2c_eeprom: eeprom@52 {
compatible = "atmel,24c32";
pagesize = <32>;
#address-cells = <1>;
#size-cells = <1>;
-
- partition@0 {
- label = "xload";
- reg = <0x0 0x20000>;
- };
- partition@1 {
- label = "xload_backup1";
- reg = <0x20000 0x20000>;
- };
- partition@2 {
- label = "xload_backup2";
- reg = <0x40000 0x20000>;
- };
- partition@3 {
- label = "xload_backup3";
- reg = <0x60000 0x20000>;
- };
- partition@4 {
- label = "barebox";
- reg = <0x80000 0x80000>;
- };
- partition@5 {
- label = "bareboxenv";
- reg = <0x100000 0x40000>;
- };
- partition@6 {
- label = "oftree";
- reg = <0x140000 0x40000>;
- };
- partition@7 {
- label = "kernel";
- reg = <0x180000 0x800000>;
- };
- partition@8 {
- label = "root";
- reg = <0x980000 0x0>;
- };
};
};
status = "okay";
serial_flash: m25p80@0 {
- compatible = "m25p80";
+ compatible = "jedec,spi-nor";
spi-max-frequency = <48000000>;
reg = <0x0>;
m25p,fast-read;
status = "disabled";
#address-cells = <1>;
#size-cells = <1>;
-
- partition@0 {
- label = "xload";
- reg = <0x0 0x20000>;
- };
- partition@1 {
- label = "barebox";
- reg = <0x20000 0x80000>;
- };
- partition@2 {
- label = "bareboxenv";
- reg = <0xa0000 0x20000>;
- };
- partition@3 {
- label = "oftree";
- reg = <0xc0000 0x20000>;
- };
- partition@4 {
- label = "kernel";
- reg = <0xe0000 0x0>;
- };
};
};
>;
};
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
uart4_pins: pinmux_uart4_pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6) /* gpmc_wait0.uart4_rxd */
>;
};
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rxd.i2c1_sda */
- AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_txdi2c1_scl */
- >;
- };
-
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */
>;
};
+ spi0_pins: pinmux_spi0_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* SPI0_MOSI - spi0_d0.spi0_d0 */
+ AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* SPI0_MISO - spi0_d1.spi0_d1 */
+ AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* SPI0_CLK - spi0_clk.spi0_clk */
+ AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* SPI0_CS0 (NBATTSS) - spi0_cs0.spi0_cs0 */
+ AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE0) /* SPI0_CS1 (FPGA_FLASH_NCS) - spi0_cs1.spi0_cs1 */
+ >;
+ };
+
lwb_pins: pinmux_lwb_pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7) /* SoundPA_en - mcasp0_fsr.gpio3_19 */
reg = <0x24>;
};
+ bq32000: rtc@68 {
+ compatible = "ti,bq32000";
+ trickle-resistor-ohms = <1120>;
+ reg = <0x68>;
+ };
+
eeprom: eeprom@50 {
compatible = "at,24c256";
reg = <0x50>;
};
-};
-&i2c1 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
+ gpio_exp: mcp23017@20 {
+ compatible = "microchip,mcp23017";
+ reg = <0x20>;
+ };
+
};
&i2c2 {
DRVDD-supply = <&ldo4_reg>;
DVDD-supply = <&ldo3_reg>;
};
+
+ /* Ambient Light Sensor */
+ als: isl29023@44 {
+ compatible = "isil,isl29023";
+ reg = <0x44>;
+ };
+};
+
+&rtc {
+ status = "disabled";
};
&usb {
pinctrl-0 = <&uart0_pins>;
};
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
&uart4 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins>;
};
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+
+ flash: n25q032@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q032";
+ reg = <1>;
+ spi-max-frequency = <5000000>;
+ };
+};
+
#include "tps65217.dtsi"
&tps {
};
&cpsw_emac1 {
- phy_id = <&davinci_mdio>, <1>;
+ phy-handle = <&phy1>;
phy-mode = "mii";
dual_emac_res_vlan = <2>;
};
+&davinci_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&mac {
slaves = <2>;
pinctrl-names = "default";
};
&usb0 {
- dr_mode = "peripheral";
status = "okay";
};
display0 = &lcd0;
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
evm_v3_3d: fixedregulator-v3_3d {
compatible = "regulator-fixed";
regulator-name = "evm_v3_3d";
model = "TI AM437x Industrial Development Kit";
compatible = "ti,am437x-idk-evm","ti,am4372","ti,am43";
+ chosen {
+ stdout-path = &uart0;
+ };
+
v24_0d: fixed-regulator-v24_0d {
compatible = "regulator-fixed";
regulator-name = "V24_0D";
display0 = &lcd0;
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
/* fixed 32k external oscillator clock */
clk_32k_rtc: clk_32k_rtc {
#clock-cells = <0>;
display0 = &lcd0;
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
vmmcsd_fixed: fixedregulator-sd {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
display0 = &hdmi0;
};
+ chosen {
+ stdout-path = &uart3;
+ };
+
memory@0 {
device_type = "memory";
reg = <0x0 0x80000000 0x0 0x80000000>;
<&dra7_pmx_core 0x3f8>;
};
+&davinci_mdio {
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@2 {
+ reg = <2>;
+ };
+};
+
&mac {
status = "okay";
dual_emac;
};
&cpsw_emac0 {
- phy_id = <&davinci_mdio>, <1>;
+ phy-handle = <&phy0>;
phy-mode = "rgmii";
dual_emac_res_vlan = <1>;
};
&cpsw_emac1 {
- phy_id = <&davinci_mdio>, <2>;
+ phy-handle = <&phy1>;
phy-mode = "rgmii";
dual_emac_res_vlan = <2>;
};
vmmc-supply = <&vdd_3v3>;
vmmc-aux-supply = <&ldo1_reg>;
};
+
+/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
+&phy1 {
+ max-speed = <100>;
+};
&mmc1 {
vmmc-supply = <&ldo1_reg>;
};
+
+/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
+&phy1 {
+ max-speed = <100>;
+};
rtc1 = &rtc;
};
+ chosen {
+ stdout-path = &uart3;
+ };
+
vmain: fixedregulator-vmain {
compatible = "regulator-fixed";
regulator-name = "VMAIN";
reg = <0x0 0x80000000 0x0 0x60000000>; /* 1536 MB */
};
+ chosen {
+ stdout-path = &uart1;
+ };
+
evm_3v3_sd: fixedregulator-sd {
compatible = "regulator-fixed";
regulator-name = "evm_3v3_sd";
};
&dra7_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&vtt_pin>;
-
- vtt_pin: pinmux_vtt_pin {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b4, PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */
- >;
- };
-
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
- >;
- };
-
- i2c2_pins: pinmux_i2c2_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
- >;
- };
-
- i2c3_pins: pinmux_i2c3_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3688, PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */
- DRA7XX_CORE_IOPAD(0x368c, PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */
- >;
- };
-
- mcspi1_pins: pinmux_mcspi1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37a4, PIN_INPUT | MUX_MODE0) /* spi1_sclk */
- DRA7XX_CORE_IOPAD(0x37a8, PIN_INPUT | MUX_MODE0) /* spi1_d1 */
- DRA7XX_CORE_IOPAD(0x37ac, PIN_INPUT | MUX_MODE0) /* spi1_d0 */
- DRA7XX_CORE_IOPAD(0x37b0, PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
- DRA7XX_CORE_IOPAD(0x37bc, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
- >;
- };
-
- mcspi2_pins: pinmux_mcspi2_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37c0, PIN_INPUT | MUX_MODE0) /* spi2_sclk */
- DRA7XX_CORE_IOPAD(0x37c4, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
- DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
- DRA7XX_CORE_IOPAD(0x37cc, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
- >;
- };
-
- uart1_pins: pinmux_uart1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37e0, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
- DRA7XX_CORE_IOPAD(0x37e4, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
- DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
- DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
- >;
- };
-
- uart2_pins: pinmux_uart2_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT | MUX_MODE0) /* uart2_rxd */
- DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT | MUX_MODE0) /* uart2_txd */
- DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
- DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
- DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- usb2_pins: pinmux_usb2_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
- >;
- };
-
- nand_flash_x16: nand_flash_x16 {
- /* On DRA7 EVM, GPMC_WPN and NAND_BOOTn comes from DIP switch
- * So NAND flash requires following switch settings:
- * SW5.1 (NAND_BOOTn) = ON (LOW)
- * SW5.9 (GPMC_WPN) = OFF (HIGH)
- */
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */
- DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */
- DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */
- DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */
- DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */
- DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */
- DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */
- DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */
- DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */
- DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */
- DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */
- DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */
- DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */
- DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */
- DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */
- DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */
- DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */
- DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */
- DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0 */
- DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */
- DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */
- DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle */
- >;
- };
-
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txc.rgmii0_txc */
- DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txctl.rgmii0_txctl */
- DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii0_td3.rgmii0_txd3 */
- DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd2.rgmii0_txd2 */
- DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd1.rgmii0_txd1 */
- DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii0_txd0.rgmii0_txd0 */
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii0_rxc.rgmii0_rxc */
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii0_rxctl.rgmii0_rxctl */
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd3.rgmii0_rxd3 */
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd2.rgmii0_rxd2 */
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd1.rgmii0_rxd1 */
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii0_rxd0.rgmii0_rxd0 */
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
- >;
-
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3654, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3658, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x365c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3660, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3664, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3668, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x366c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3670, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3674, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3678, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x367c, MUX_MODE15)
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15)
- >;
- };
-
dcan1_pins_default: dcan1_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
>;
};
- atl_pins: pinmux_atl_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */
- DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */
- >;
- };
-
- mcasp3_pins: pinmux_mcasp3_pins {
+ mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */
+ DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
+ DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+ DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+ DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+ DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+ DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+ DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
>;
};
- mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins {
+ mmc2_pins_default: mmc2_pins_default {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, MUX_MODE15)
+ DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+ DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+ DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+ DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+ DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+ DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+ DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+ DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+ DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+ DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
>;
};
};
&i2c1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
tps659038: tps659038@58 {
&i2c2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
clock-frequency = <400000>;
pcf_hdmi: gpio@26 {
&i2c3 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins>;
clock-frequency = <400000>;
};
&mcspi1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mcspi1_pins>;
};
&mcspi2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mcspi2_pins>;
};
&uart1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x3e0>;
};
&uart2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
};
&uart3 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
};
&mmc1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&evm_3v3_sd>;
vmmc_aux-supply = <&ldo1_reg>;
bus-width = <4>;
&mmc2 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_default>;
vmmc-supply = <&evm_3v3_sw>;
bus-width = <8>;
};
&usb1 {
dr_mode = "peripheral";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
};
&usb2 {
dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_pins>;
};
&elm {
};
&gpmc {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nand_flash_x16>;
+ /*
+ * For the existing IOdelay configuration via U-Boot we don't
+ * support NAND on dra7-evm. Keep it disabled. Enabling it
+ * requires a different configuration by U-Boot.
+ */
+ status = "disabled";
ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
nand@0,0 {
compatible = "ti,omap2-nand";
&mac {
status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_default>;
- pinctrl-1 = <&cpsw_sleep>;
dual_emac;
};
dual_emac_res_vlan = <2>;
};
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_default>;
- pinctrl-1 = <&davinci_mdio_sleep>;
-};
-
&dcan1 {
status = "ok";
pinctrl-names = "default", "sleep", "active";
};
&atl {
- pinctrl-names = "default";
- pinctrl-0 = <&atl_pins>;
-
assigned-clocks = <&abe_dpll_sys_clk_mux>,
<&atl_gfclk_mux>,
<&dpll_abe_ck>,
&mcasp3 {
#sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins>;
- pinctrl-1 = <&mcasp3_sleep_pins>;
assigned-clocks = <&mcasp3_ahclkx_mux>;
assigned-clock-parents = <&atl_clkin2_ck>;
};
};
+&pcf_lcd {
+ interrupt-parent = <&gpio7>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+};
+
&pcf_gpio_21 {
interrupt-parent = <&gpio7>;
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
display0 = &hdmi0;
};
+ chosen {
+ stdout-path = &uart1;
+ };
+
evm_12v0: fixedregulator-evm12v0 {
/* main supply */
compatible = "regulator-fixed";
status = "okay";
clock-frequency = <400000>;
+ pcf_lcd: gpio@20 {
+ compatible = "nxp,pcf8575";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
pcf_gpio_21: gpio@21 {
compatible = "ti,pcf8575", "nxp,pcf8575";
reg = <0x21>;
};
&gpmc {
- status = "okay";
+ /*
+ * For the existing IOdelay configuration via U-Boot we don't
+ * support NAND on dra72-evm. Keep it disabled. Enabling it
+ * requires a different configuration by U-Boot.
+ */
+ status = "disabled";
ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
nand@0,0 {
/* To use NAND, DIP switch SW5 must be set like so:
ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
ti,min-output-impedance;
+ interrupt-parent = <&gpio6>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
};
dp83867_1: ethernet-phy@3 {
ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
ti,min-output-impedance;
+ interrupt-parent = <&gpio6>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
};
};
aliases {
display0 = &dvi0;
display1 = &tv0;
+ ethernet = ðernet;
};
leds {
&usbhsehci {
phys = <0 &hsusb2_phy>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub@2 {
+ compatible = "usb424,9514";
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: usbether@1 {
+ compatible = "usb424,ec00";
+ reg = <1>;
+ };
+ };
};
&vaux2 {
#address-cells = <1>;
#size-cells = <1>;
-
- partition@0 {
- label = "SPL";
- reg = <0 0x100000>;
- };
- partition@80000 {
- label = "U-Boot";
- reg = <0x100000 0x180000>;
- };
- partition@1c0000 {
- label = "Environment";
- reg = <0x280000 0x100000>;
- };
- partition@280000 {
- label = "Kernel";
- reg = <0x380000 0x300000>;
- };
- partition@780000 {
- label = "Filesystem";
- reg = <0x680000 0x1f980000>;
- };
};
};
compatible = "gpio-leds";
heartbeat {
label = "debug::sleep";
- gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio162 */
+ gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* 162 */
linux,default-trigger = "default-on";
pinctrl-names = "default";
pinctrl-0 = <&debug_leds>;
reg = <0x55>;
};
+ /* Stereo headphone amplifier */
tpa6130a2: tpa6130a2@60 {
compatible = "ti,tpa6130a2";
reg = <0x60>;
aliases {
display0 = &dvi0;
display1 = &hdmi0;
+ ethernet = ðernet;
};
leds: leds {
&usbhsehci {
phys = <&hsusb1_phy>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub@1 {
+ compatible = "usb424,9514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: usbether@1 {
+ compatible = "usb424,ec00";
+ reg = <1>;
+ };
+ };
};
&dss {
reg = <0x0 0x80000000 0 0x7f000000>; /* 2032 MB */
};
+ aliases {
+ ethernet = ðernet;
+ };
+
gpio_keys {
compatible = "gpio-keys";
pinctrl-0 = <&power_button_pin>;
OMAP5_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */
>;
};
+
+&usbhsehci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub@2 {
+ compatible = "usb424,3503";
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: usbether@3 {
+ compatible = "usb424,7500";
+ reg = <3>;
+ };
+ };
+};
reg = <0 0x80000000 0 0x7f000000>; /* 2032 MB */
};
+ aliases {
+ ethernet = ðernet;
+ };
+
leds {
compatible = "gpio-leds";
led1 {
>;
};
+&usbhsehci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub@2 {
+ compatible = "usb424,3503";
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ethernet: usbether@3 {
+ compatible = "usb424,9730";
+ reg = <3>;
+ };
+};
+
&wlcore {
compatible = "ti,wl1837";
};
projects / mirror_ubuntu-bionic-kernel.git / commitdiff