select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_EARLY_PRINTK
-config MIPS_PB1000
- bool "Alchemy PB1000 board"
- select ALCHEMY_GPIOINT_AU1000
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select SWAP_IO_SPACE
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_HAS_EARLY_PRINTK
-
config MIPS_PB1100
bool "Alchemy PB1100 board"
select ALCHEMY_GPIOINT_AU1000
platform-$(CONFIG_MIPS_ALCHEMY) += alchemy/common/
-#
-# AMD Alchemy Pb1000 eval board
-#
-platform-$(CONFIG_MIPS_PB1000) += alchemy/devboards/
-cflags-$(CONFIG_MIPS_PB1000) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
-load-$(CONFIG_MIPS_PB1000) += 0xffffffff80100000
-
#
# AMD Alchemy Pb1100 eval board
#
#include <asm/irq_cpu.h>
#include <asm/mipsregs.h>
#include <asm/mach-au1x00/au1000.h>
-#ifdef CONFIG_MIPS_PB1000
-#include <asm/mach-pb1x00/pb1000.h>
-#endif
/* Interrupt Controller register offsets */
#define IC_CFG0RD 0x40
__raw_writel(1 << bit, base + IC_MASKSET);
__raw_writel(1 << bit, base + IC_WAKESET);
-
-/* very hacky. does the pb1000 cpld auto-disable this int?
- * nowhere in the current kernel sources is it disabled. --mlau
- */
-#if defined(CONFIG_MIPS_PB1000)
- if (d->irq == AU1000_GPIO15_INT)
- __raw_writel(0x4000, (void __iomem *)PB1000_MDR); /* enable int */
-#endif
wmb();
}
obj-y += prom.o bcsr.o platform.o
obj-$(CONFIG_PM) += pm.o
-obj-$(CONFIG_MIPS_PB1000) += pb1000/
obj-$(CONFIG_MIPS_PB1100) += pb1100/
obj-$(CONFIG_MIPS_PB1200) += pb1200/
obj-$(CONFIG_MIPS_PB1500) += pb1500/
+++ /dev/null
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1000 board.
-#
-
-obj-y := board_setup.o
+++ /dev/null
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1000.h>
-#include <asm/reboot.h>
-#include <prom.h>
-
-#include "../platform.h"
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1000";
-}
-
-static void board_reset(char *c)
-{
- asm volatile ("jr %0" : : "r" (0xbfc00000));
-}
-
-static void board_power_off(void)
-{
- while (1)
- asm volatile (
- " .set mips32 \n"
- " wait \n"
- " .set mips0 \n");
-}
-
-void __init board_setup(void)
-{
- u32 pin_func, static_cfg0;
- u32 sys_freqctrl, sys_clksrc;
- u32 prid = read_c0_prid();
-
- sys_freqctrl = 0;
- sys_clksrc = 0;
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- alchemy_gpio1_input_enable();
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- /* CPU core freq to 48 MHz to slow it way down... */
- au_writel(4, SYS_CPUPLL);
-
- /*
- * Setup 48 MHz FREQ2 from CPUPLL for USB Host
- * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
- */
- sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* CPU core freq to 384 MHz */
- au_writel(0x20, SYS_CPUPLL);
-
- printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
- break;
-
- default: /* HC and newer */
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
- break;
- }
-
- /*
- * Route 48 MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
-
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
-
- au_writel(pin_func, SYS_PINFUNC);
-
- alchemy_gpio_direction_input(11);
- alchemy_gpio_direction_input(13);
- alchemy_gpio_direction_output(4, 0);
- alchemy_gpio_direction_output(5, 0);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Make GPIO 15 an input (for interrupt line) */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
- /* We don't need I2S, so make it available for GPIO[31:29] */
- pin_func |= SYS_PF_I2S;
- au_writel(pin_func, SYS_PINFUNC);
-
- alchemy_gpio_direction_input(15);
-
- static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
- au_writel(static_cfg0, MEM_STCFG0);
-
- /* configure RCE2* for LCD */
- au_writel(0x00000004, MEM_STCFG2);
-
- /* MEM_STTIME2 */
- au_writel(0x09000000, MEM_STTIME2);
-
- /* Set 32-bit base address decoding for RCE2* */
- au_writel(0x10003ff0, MEM_STADDR2);
-
- /*
- * PCI CPLD setup
- * Expand CE0 to cover PCI
- */
- au_writel(0x11803e40, MEM_STADDR1);
-
- /* Burst visibility on */
- au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
-
- au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */
- au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Enable Au1000 BCLK switching - note: sed1356 must not use
- * its BCLK (Au1000 LCLK) for any timings
- */
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- break;
- default: /* HC and newer */
- /*
- * Enable sys bus clock divider when IDLE state or no bus
- * activity.
- */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
- break;
- }
-
- pm_power_off = board_power_off;
- _machine_halt = board_power_off;
- _machine_restart = board_reset;
-}
-
-static int __init pb1000_init_irq(void)
-{
- irq_set_irq_type(AU1000_GPIO15_INT, IRQF_TRIGGER_LOW);
- return 0;
-}
-arch_initcall(pb1000_init_irq);
-
-static int __init pb1000_device_init(void)
-{
- return db1x_register_norflash(8 * 1024 * 1024, 4, 0);
-}
-device_initcall(pb1000_device_init);
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_DB1000) || \
+#if defined(CONFIG_MIPS_DB1000) || \
defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500) || \
defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
+++ /dev/null
-/*
- * Alchemy Semi Pb1000 Reference Board
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#ifndef __ASM_PB1000_H
-#define __ASM_PB1000_H
-
-/* PCMCIA PB1000 specific defines */
-#define PCMCIA_MAX_SOCK 1
-#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK + 1)
-
-#define PB1000_PCR 0xBE000000
-# define PCR_SLOT_0_VPP0 (1 << 0)
-# define PCR_SLOT_0_VPP1 (1 << 1)
-# define PCR_SLOT_0_VCC0 (1 << 2)
-# define PCR_SLOT_0_VCC1 (1 << 3)
-# define PCR_SLOT_0_RST (1 << 4)
-# define PCR_SLOT_1_VPP0 (1 << 8)
-# define PCR_SLOT_1_VPP1 (1 << 9)
-# define PCR_SLOT_1_VCC0 (1 << 10)
-# define PCR_SLOT_1_VCC1 (1 << 11)
-# define PCR_SLOT_1_RST (1 << 12)
-
-#define PB1000_MDR 0xBE000004
-# define MDR_PI (1 << 5) /* PCMCIA int latch */
-# define MDR_EPI (1 << 14) /* enable PCMCIA int */
-# define MDR_CPI (1 << 15) /* clear PCMCIA int */
-
-#define PB1000_ACR1 0xBE000008
-# define ACR1_SLOT_0_CD1 (1 << 0) /* card detect 1 */
-# define ACR1_SLOT_0_CD2 (1 << 1) /* card detect 2 */
-# define ACR1_SLOT_0_READY (1 << 2) /* ready */
-# define ACR1_SLOT_0_STATUS (1 << 3) /* status change */
-# define ACR1_SLOT_0_VS1 (1 << 4) /* voltage sense 1 */
-# define ACR1_SLOT_0_VS2 (1 << 5) /* voltage sense 2 */
-# define ACR1_SLOT_0_INPACK (1 << 6) /* inpack pin status */
-# define ACR1_SLOT_1_CD1 (1 << 8) /* card detect 1 */
-# define ACR1_SLOT_1_CD2 (1 << 9) /* card detect 2 */
-# define ACR1_SLOT_1_READY (1 << 10) /* ready */
-# define ACR1_SLOT_1_STATUS (1 << 11) /* status change */
-# define ACR1_SLOT_1_VS1 (1 << 12) /* voltage sense 1 */
-# define ACR1_SLOT_1_VS2 (1 << 13) /* voltage sense 2 */
-# define ACR1_SLOT_1_INPACK (1 << 14) /* inpack pin status */
-
-#define CPLD_AUX0 0xBE00000C
-#define CPLD_AUX1 0xBE000010
-#define CPLD_AUX2 0xBE000014
-
-/* Voltage levels */
-
-/* VPPEN1 - VPPEN0 */
-#define VPP_GND ((0 << 1) | (0 << 0))
-#define VPP_5V ((1 << 1) | (0 << 0))
-#define VPP_3V ((0 << 1) | (1 << 0))
-#define VPP_12V ((0 << 1) | (1 << 0))
-#define VPP_HIZ ((1 << 1) | (1 << 0))
-
-/* VCCEN1 - VCCEN0 */
-#define VCC_3V ((0 << 1) | (1 << 0))
-#define VCC_5V ((1 << 1) | (0 << 0))
-#define VCC_HIZ ((0 << 1) | (0 << 0))
-
-/* VPP/VCC */
-#define SET_VCC_VPP(VCC, VPP, SLOT) \
- ((((VCC) << 2) | ((VPP) << 0)) << ((SLOT) * 8))
-#endif /* __ASM_PB1000_H */
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/au1000.h>
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_PB1100)
-#include <asm/pb1000.h>
-#elif defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
-#include <asm/db1x00.h>
+#if defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100)
#include <asm/mach-db1x00/bcsr.h>
#else
#error au1k_ir: unsupported board
This driver is also available as a module called m8xx_pcmcia.
-config PCMCIA_AU1X00
- tristate "Au1x00 pcmcia support"
- depends on MIPS_ALCHEMY && PCMCIA
-
config PCMCIA_ALCHEMY_DEVBOARD
tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
depends on MIPS_ALCHEMY && PCMCIA
obj-$(CONFIG_PCMCIA_SA1111) += sa11xx_base.o sa1111_cs.o
obj-$(CONFIG_M32R_PCC) += m32r_pcc.o
obj-$(CONFIG_M32R_CFC) += m32r_cfc.o
-obj-$(CONFIG_PCMCIA_AU1X00) += au1x00_ss.o
obj-$(CONFIG_PCMCIA_BCM63XX) += bcm63xx_pcmcia.o
obj-$(CONFIG_PCMCIA_VRC4171) += vrc4171_card.o
obj-$(CONFIG_PCMCIA_VRC4173) += vrc4173_cardu.o
obj-$(CONFIG_ELECTRA_CF) += electra_cf.o
obj-$(CONFIG_PCMCIA_ALCHEMY_DEVBOARD) += db1xxx_ss.o
-au1x00_ss-y += au1000_generic.o
-au1x00_ss-$(CONFIG_MIPS_PB1000) += au1000_pb1x00.o
-
sa1111_cs-y += sa1111_generic.o
sa1111_cs-$(CONFIG_ASSABET_NEPONSET) += sa1100_neponset.o
sa1111_cs-$(CONFIG_SA1100_BADGE4) += sa1100_badge4.o
+++ /dev/null
-/*
- *
- * Alchemy Semi Au1000 pcmcia driver
- *
- * Copyright 2001-2003 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@embeddedalley.com or source@mvista.com
- *
- * Copyright 2004 Pete Popov, Embedded Alley Solutions, Inc.
- * Updated the driver to 2.6. Followed the sa11xx API and largely
- * copied many of the hardware independent functions.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/cpufreq.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/notifier.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include "au1000_generic.h"
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Pete Popov <ppopov@embeddedalley.com>");
-MODULE_DESCRIPTION("Linux PCMCIA Card Services: Au1x00 Socket Controller");
-
-#if 0
-#define debug(x,args...) printk(KERN_DEBUG "%s: " x, __func__ , ##args)
-#else
-#define debug(x,args...)
-#endif
-
-#define MAP_SIZE 0x100000
-extern struct au1000_pcmcia_socket au1000_pcmcia_socket[];
-#define PCMCIA_SOCKET(x) (au1000_pcmcia_socket + (x))
-#define to_au1000_socket(x) container_of(x, struct au1000_pcmcia_socket, socket)
-
-/* Some boards like to support CF cards as IDE root devices, so they
- * grab pcmcia sockets directly.
- */
-u32 *pcmcia_base_vaddrs[2];
-extern const unsigned long mips_io_port_base;
-
-static DEFINE_MUTEX(pcmcia_sockets_lock);
-
-static int (*au1x00_pcmcia_hw_init[])(struct device *dev) = {
- au1x_board_init,
-};
-
-static int
-au1x00_pcmcia_skt_state(struct au1000_pcmcia_socket *skt)
-{
- struct pcmcia_state state;
- unsigned int stat;
-
- memset(&state, 0, sizeof(struct pcmcia_state));
-
- skt->ops->socket_state(skt, &state);
-
- stat = state.detect ? SS_DETECT : 0;
- stat |= state.ready ? SS_READY : 0;
- stat |= state.wrprot ? SS_WRPROT : 0;
- stat |= state.vs_3v ? SS_3VCARD : 0;
- stat |= state.vs_Xv ? SS_XVCARD : 0;
- stat |= skt->cs_state.Vcc ? SS_POWERON : 0;
-
- if (skt->cs_state.flags & SS_IOCARD)
- stat |= state.bvd1 ? SS_STSCHG : 0;
- else {
- if (state.bvd1 == 0)
- stat |= SS_BATDEAD;
- else if (state.bvd2 == 0)
- stat |= SS_BATWARN;
- }
- return stat;
-}
-
-/*
- * au100_pcmcia_config_skt
- *
- * Convert PCMCIA socket state to our socket configure structure.
- */
-static int
-au1x00_pcmcia_config_skt(struct au1000_pcmcia_socket *skt, socket_state_t *state)
-{
- int ret;
-
- ret = skt->ops->configure_socket(skt, state);
- if (ret == 0) {
- skt->cs_state = *state;
- }
-
- if (ret < 0)
- debug("unable to configure socket %d\n", skt->nr);
-
- return ret;
-}
-
-/* au1x00_pcmcia_sock_init()
- *
- * (Re-)Initialise the socket, turning on status interrupts
- * and PCMCIA bus. This must wait for power to stabilise
- * so that the card status signals report correctly.
- *
- * Returns: 0
- */
-static int au1x00_pcmcia_sock_init(struct pcmcia_socket *sock)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("initializing socket %u\n", skt->nr);
-
- skt->ops->socket_init(skt);
- return 0;
-}
-
-/*
- * au1x00_pcmcia_suspend()
- *
- * Remove power on the socket, disable IRQs from the card.
- * Turn off status interrupts, and disable the PCMCIA bus.
- *
- * Returns: 0
- */
-static int au1x00_pcmcia_suspend(struct pcmcia_socket *sock)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("suspending socket %u\n", skt->nr);
-
- skt->ops->socket_suspend(skt);
-
- return 0;
-}
-
-static DEFINE_SPINLOCK(status_lock);
-
-/*
- * au1x00_check_status()
- */
-static void au1x00_check_status(struct au1000_pcmcia_socket *skt)
-{
- unsigned int events;
-
- debug("entering PCMCIA monitoring thread\n");
-
- do {
- unsigned int status;
- unsigned long flags;
-
- status = au1x00_pcmcia_skt_state(skt);
-
- spin_lock_irqsave(&status_lock, flags);
- events = (status ^ skt->status) & skt->cs_state.csc_mask;
- skt->status = status;
- spin_unlock_irqrestore(&status_lock, flags);
-
- debug("events: %s%s%s%s%s%s\n",
- events == 0 ? "<NONE>" : "",
- events & SS_DETECT ? "DETECT " : "",
- events & SS_READY ? "READY " : "",
- events & SS_BATDEAD ? "BATDEAD " : "",
- events & SS_BATWARN ? "BATWARN " : "",
- events & SS_STSCHG ? "STSCHG " : "");
-
- if (events)
- pcmcia_parse_events(&skt->socket, events);
- } while (events);
-}
-
-/*
- * au1x00_pcmcia_poll_event()
- * Let's poll for events in addition to IRQs since IRQ only is unreliable...
- */
-static void au1x00_pcmcia_poll_event(unsigned long dummy)
-{
- struct au1000_pcmcia_socket *skt = (struct au1000_pcmcia_socket *)dummy;
- debug("polling for events\n");
-
- mod_timer(&skt->poll_timer, jiffies + AU1000_PCMCIA_POLL_PERIOD);
-
- au1x00_check_status(skt);
-}
-
-/* au1x00_pcmcia_get_status()
- *
- * From the sa11xx_core.c:
- * Implements the get_status() operation for the in-kernel PCMCIA
- * service (formerly SS_GetStatus in Card Services). Essentially just
- * fills in bits in `status' according to internal driver state or
- * the value of the voltage detect chipselect register.
- *
- * As a debugging note, during card startup, the PCMCIA core issues
- * three set_socket() commands in a row the first with RESET deasserted,
- * the second with RESET asserted, and the last with RESET deasserted
- * again. Following the third set_socket(), a get_status() command will
- * be issued. The kernel is looking for the SS_READY flag (see
- * setup_socket(), reset_socket(), and unreset_socket() in cs.c).
- *
- * Returns: 0
- */
-static int
-au1x00_pcmcia_get_status(struct pcmcia_socket *sock, unsigned int *status)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- skt->status = au1x00_pcmcia_skt_state(skt);
- *status = skt->status;
-
- return 0;
-}
-
-/* au1x00_pcmcia_set_socket()
- * Implements the set_socket() operation for the in-kernel PCMCIA
- * service (formerly SS_SetSocket in Card Services). We more or
- * less punt all of this work and let the kernel handle the details
- * of power configuration, reset, &c. We also record the value of
- * `state' in order to regurgitate it to the PCMCIA core later.
- *
- * Returns: 0
- */
-static int
-au1x00_pcmcia_set_socket(struct pcmcia_socket *sock, socket_state_t *state)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
-
- debug("for sock %u\n", skt->nr);
-
- debug("\tmask: %s%s%s%s%s%s\n\tflags: %s%s%s%s%s%s\n",
- (state->csc_mask==0)?"<NONE>":"",
- (state->csc_mask&SS_DETECT)?"DETECT ":"",
- (state->csc_mask&SS_READY)?"READY ":"",
- (state->csc_mask&SS_BATDEAD)?"BATDEAD ":"",
- (state->csc_mask&SS_BATWARN)?"BATWARN ":"",
- (state->csc_mask&SS_STSCHG)?"STSCHG ":"",
- (state->flags==0)?"<NONE>":"",
- (state->flags&SS_PWR_AUTO)?"PWR_AUTO ":"",
- (state->flags&SS_IOCARD)?"IOCARD ":"",
- (state->flags&SS_RESET)?"RESET ":"",
- (state->flags&SS_SPKR_ENA)?"SPKR_ENA ":"",
- (state->flags&SS_OUTPUT_ENA)?"OUTPUT_ENA ":"");
- debug("\tVcc %d Vpp %d irq %d\n",
- state->Vcc, state->Vpp, state->io_irq);
-
- return au1x00_pcmcia_config_skt(skt, state);
-}
-
-int
-au1x00_pcmcia_set_io_map(struct pcmcia_socket *sock, struct pccard_io_map *map)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
- unsigned int speed;
-
- if(map->map>=MAX_IO_WIN){
- debug("map (%d) out of range\n", map->map);
- return -1;
- }
-
- if(map->flags&MAP_ACTIVE){
- speed=(map->speed>0)?map->speed:AU1000_PCMCIA_IO_SPEED;
- skt->spd_io[map->map] = speed;
- }
-
- map->start=(unsigned int)(u32)skt->virt_io;
- map->stop=map->start+MAP_SIZE;
- return 0;
-
-} /* au1x00_pcmcia_set_io_map() */
-
-
-static int
-au1x00_pcmcia_set_mem_map(struct pcmcia_socket *sock, struct pccard_mem_map *map)
-{
- struct au1000_pcmcia_socket *skt = to_au1000_socket(sock);
- unsigned short speed = map->speed;
-
- if(map->map>=MAX_WIN){
- debug("map (%d) out of range\n", map->map);
- return -1;
- }
-
- if (map->flags & MAP_ATTRIB) {
- skt->spd_attr[map->map] = speed;
- skt->spd_mem[map->map] = 0;
- } else {
- skt->spd_attr[map->map] = 0;
- skt->spd_mem[map->map] = speed;
- }
-
- if (map->flags & MAP_ATTRIB) {
- map->static_start = skt->phys_attr + map->card_start;
- }
- else {
- map->static_start = skt->phys_mem + map->card_start;
- }
-
- debug("set_mem_map %d start %08lx card_start %08x\n",
- map->map, map->static_start, map->card_start);
- return 0;
-
-} /* au1x00_pcmcia_set_mem_map() */
-
-static struct pccard_operations au1x00_pcmcia_operations = {
- .init = au1x00_pcmcia_sock_init,
- .suspend = au1x00_pcmcia_suspend,
- .get_status = au1x00_pcmcia_get_status,
- .set_socket = au1x00_pcmcia_set_socket,
- .set_io_map = au1x00_pcmcia_set_io_map,
- .set_mem_map = au1x00_pcmcia_set_mem_map,
-};
-
-static const char *skt_names[] = {
- "PCMCIA socket 0",
- "PCMCIA socket 1",
-};
-
-struct skt_dev_info {
- int nskt;
-};
-
-int au1x00_pcmcia_socket_probe(struct device *dev, struct pcmcia_low_level *ops, int first, int nr)
-{
- struct skt_dev_info *sinfo;
- struct au1000_pcmcia_socket *skt;
- int ret, i;
-
- sinfo = kzalloc(sizeof(struct skt_dev_info), GFP_KERNEL);
- if (!sinfo) {
- ret = -ENOMEM;
- goto out;
- }
-
- sinfo->nskt = nr;
-
- /*
- * Initialise the per-socket structure.
- */
- for (i = 0; i < nr; i++) {
- skt = PCMCIA_SOCKET(i);
- memset(skt, 0, sizeof(*skt));
-
- skt->socket.resource_ops = &pccard_static_ops;
- skt->socket.ops = &au1x00_pcmcia_operations;
- skt->socket.owner = ops->owner;
- skt->socket.dev.parent = dev;
-
- init_timer(&skt->poll_timer);
- skt->poll_timer.function = au1x00_pcmcia_poll_event;
- skt->poll_timer.data = (unsigned long)skt;
- skt->poll_timer.expires = jiffies + AU1000_PCMCIA_POLL_PERIOD;
-
- skt->nr = first + i;
- skt->irq = 255;
- skt->dev = dev;
- skt->ops = ops;
-
- skt->res_skt.name = skt_names[skt->nr];
- skt->res_io.name = "io";
- skt->res_io.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
- skt->res_mem.name = "memory";
- skt->res_mem.flags = IORESOURCE_MEM;
- skt->res_attr.name = "attribute";
- skt->res_attr.flags = IORESOURCE_MEM;
-
- /*
- * PCMCIA client drivers use the inb/outb macros to access the
- * IO registers. Since mips_io_port_base is added to the
- * access address of the mips implementation of inb/outb,
- * we need to subtract it here because we want to access the
- * I/O or MEM address directly, without going through this
- * "mips_io_port_base" mechanism.
- */
- if (i == 0) {
- skt->virt_io = (void *)
- (ioremap((phys_t)AU1X_SOCK0_IO, 0x1000) -
- (u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK0_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK0_PHYS_MEM;
- }
- else {
- skt->virt_io = (void *)
- (ioremap((phys_t)AU1X_SOCK1_IO, 0x1000) -
- (u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK1_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK1_PHYS_MEM;
- }
- pcmcia_base_vaddrs[i] = (u32 *)skt->virt_io;
- ret = ops->hw_init(skt);
-
- skt->socket.features = SS_CAP_STATIC_MAP|SS_CAP_PCCARD;
- skt->socket.irq_mask = 0;
- skt->socket.map_size = MAP_SIZE;
- skt->socket.pci_irq = skt->irq;
- skt->socket.io_offset = (unsigned long)skt->virt_io;
-
- skt->status = au1x00_pcmcia_skt_state(skt);
-
- ret = pcmcia_register_socket(&skt->socket);
- if (ret)
- goto out_err;
-
- WARN_ON(skt->socket.sock != i);
-
- add_timer(&skt->poll_timer);
- }
-
- dev_set_drvdata(dev, sinfo);
- return 0;
-
-
-out_err:
- ops->hw_shutdown(skt);
- while (i-- > 0) {
- skt = PCMCIA_SOCKET(i);
-
- del_timer_sync(&skt->poll_timer);
- pcmcia_unregister_socket(&skt->socket);
- if (i == 0) {
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-#ifndef CONFIG_MIPS_XXS1500
- else {
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-#endif
- ops->hw_shutdown(skt);
-
- }
- kfree(sinfo);
-out:
- return ret;
-}
-
-int au1x00_drv_pcmcia_remove(struct platform_device *dev)
-{
- struct skt_dev_info *sinfo = platform_get_drvdata(dev);
- int i;
-
- mutex_lock(&pcmcia_sockets_lock);
- platform_set_drvdata(dev, NULL);
-
- for (i = 0; i < sinfo->nskt; i++) {
- struct au1000_pcmcia_socket *skt = PCMCIA_SOCKET(i);
-
- del_timer_sync(&skt->poll_timer);
- pcmcia_unregister_socket(&skt->socket);
- skt->ops->hw_shutdown(skt);
- au1x00_pcmcia_config_skt(skt, &dead_socket);
- iounmap(skt->virt_io + (u32)mips_io_port_base);
- skt->virt_io = NULL;
- }
-
- kfree(sinfo);
- mutex_unlock(&pcmcia_sockets_lock);
- return 0;
-}
-
-
-/*
- * PCMCIA "Driver" API
- */
-
-static int au1x00_drv_pcmcia_probe(struct platform_device *dev)
-{
- int i, ret = -ENODEV;
-
- mutex_lock(&pcmcia_sockets_lock);
- for (i=0; i < ARRAY_SIZE(au1x00_pcmcia_hw_init); i++) {
- ret = au1x00_pcmcia_hw_init[i](&dev->dev);
- if (ret == 0)
- break;
- }
- mutex_unlock(&pcmcia_sockets_lock);
- return ret;
-}
-
-static struct platform_driver au1x00_pcmcia_driver = {
- .driver = {
- .name = "au1x00-pcmcia",
- .owner = THIS_MODULE,
- },
- .probe = au1x00_drv_pcmcia_probe,
- .remove = au1x00_drv_pcmcia_remove,
-};
-
-
-/* au1x00_pcmcia_init()
- *
- * This routine performs low-level PCMCIA initialization and then
- * registers this socket driver with Card Services.
- *
- * Returns: 0 on success, -ve error code on failure
- */
-static int __init au1x00_pcmcia_init(void)
-{
- int error = 0;
- error = platform_driver_register(&au1x00_pcmcia_driver);
- return error;
-}
-
-/* au1x00_pcmcia_exit()
- * Invokes the low-level kernel service to free IRQs associated with this
- * socket controller and reset GPIO edge detection.
- */
-static void __exit au1x00_pcmcia_exit(void)
-{
- platform_driver_unregister(&au1x00_pcmcia_driver);
-}
-
-module_init(au1x00_pcmcia_init);
-module_exit(au1x00_pcmcia_exit);
+++ /dev/null
-/*
- * Alchemy Semi Au1000 pcmcia driver include file
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#ifndef __ASM_AU1000_PCMCIA_H
-#define __ASM_AU1000_PCMCIA_H
-
-/* include the world */
-
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-#include "cs_internal.h"
-
-#define AU1000_PCMCIA_POLL_PERIOD (2*HZ)
-#define AU1000_PCMCIA_IO_SPEED (255)
-#define AU1000_PCMCIA_MEM_SPEED (300)
-
-#define AU1X_SOCK0_IO 0xF00000000ULL
-#define AU1X_SOCK0_PHYS_ATTR 0xF40000000ULL
-#define AU1X_SOCK0_PHYS_MEM 0xF80000000ULL
-
-/* pcmcia socket 1 needs external glue logic so the memory map
- * differs from board to board.
- */
-#if defined(CONFIG_MIPS_PB1000)
-#define AU1X_SOCK1_IO 0xF08000000ULL
-#define AU1X_SOCK1_PHYS_ATTR 0xF48000000ULL
-#define AU1X_SOCK1_PHYS_MEM 0xF88000000ULL
-#endif
-
-struct pcmcia_state {
- unsigned detect: 1,
- ready: 1,
- wrprot: 1,
- bvd1: 1,
- bvd2: 1,
- vs_3v: 1,
- vs_Xv: 1;
-};
-
-struct pcmcia_configure {
- unsigned sock: 8,
- vcc: 8,
- vpp: 8,
- output: 1,
- speaker: 1,
- reset: 1;
-};
-
-struct pcmcia_irqs {
- int sock;
- int irq;
- const char *str;
-};
-
-
-struct au1000_pcmcia_socket {
- struct pcmcia_socket socket;
-
- /*
- * Info from low level handler
- */
- struct device *dev;
- unsigned int nr;
- unsigned int irq;
-
- /*
- * Core PCMCIA state
- */
- struct pcmcia_low_level *ops;
-
- unsigned int status;
- socket_state_t cs_state;
-
- unsigned short spd_io[MAX_IO_WIN];
- unsigned short spd_mem[MAX_WIN];
- unsigned short spd_attr[MAX_WIN];
-
- struct resource res_skt;
- struct resource res_io;
- struct resource res_mem;
- struct resource res_attr;
-
- void * virt_io;
- unsigned int phys_io;
- unsigned int phys_attr;
- unsigned int phys_mem;
- unsigned short speed_io, speed_attr, speed_mem;
-
- unsigned int irq_state;
-
- struct timer_list poll_timer;
-};
-
-struct pcmcia_low_level {
- struct module *owner;
-
- int (*hw_init)(struct au1000_pcmcia_socket *);
- void (*hw_shutdown)(struct au1000_pcmcia_socket *);
-
- void (*socket_state)(struct au1000_pcmcia_socket *, struct pcmcia_state *);
- int (*configure_socket)(struct au1000_pcmcia_socket *, struct socket_state_t *);
-
- /*
- * Enable card status IRQs on (re-)initialisation. This can
- * be called at initialisation, power management event, or
- * pcmcia event.
- */
- void (*socket_init)(struct au1000_pcmcia_socket *);
-
- /*
- * Disable card status IRQs and PCMCIA bus on suspend.
- */
- void (*socket_suspend)(struct au1000_pcmcia_socket *);
-};
-
-extern int au1x_board_init(struct device *dev);
-
-#endif /* __ASM_AU1000_PCMCIA_H */
+++ /dev/null
-/*
- *
- * Alchemy Semi Pb1000 boards specific pcmcia routines.
- *
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/proc_fs.h>
-#include <linux/types.h>
-
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/au1000.h>
-#include <asm/au1000_pcmcia.h>
-
-#define debug(fmt, arg...) do { } while (0)
-
-#include <asm/pb1000.h>
-#define PCMCIA_IRQ AU1000_GPIO_15
-
-static int pb1x00_pcmcia_init(struct pcmcia_init *init)
-{
- u16 pcr;
- pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
-
- au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */
- au_sync_delay(100);
- au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */
- au_sync();
-
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(20);
-
- return PCMCIA_NUM_SOCKS;
-}
-
-static int pb1x00_pcmcia_shutdown(void)
-{
- u16 pcr;
- pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(20);
- return 0;
-}
-
-static int
-pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
-{
- u32 inserted0, inserted1;
- u16 vs0, vs1;
-
- vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
- inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
- inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
- vs0 = (vs0 >> 4) & 0x3;
- vs1 = (vs1 >> 12) & 0x3;
-
- state->ready = 0;
- state->vs_Xv = 0;
- state->vs_3v = 0;
- state->detect = 0;
-
- if (sock == 0) {
- if (inserted0) {
- switch (vs0) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "pb1x00 bad VS (%d)\n",
- vs0);
- return 0;
- }
- state->detect = 1;
- }
- }
- else {
- if (inserted1) {
- switch (vs1) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "pb1x00 bad VS (%d)\n",
- vs1);
- return 0;
- }
- state->detect = 1;
- }
- }
-
- if (state->detect) {
- state->ready = 1;
- }
-
- state->bvd1=1;
- state->bvd2=1;
- state->wrprot=0;
- return 1;
-}
-
-
-static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
-{
-
- if(info->sock > PCMCIA_MAX_SOCK) return -1;
-
- /*
- * Even in the case of the Pb1000, both sockets are connected
- * to the same irq line.
- */
- info->irq = PCMCIA_IRQ;
-
- return 0;
-}
-
-
-static int
-pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
-{
- u16 pcr;
-
- if(configure->sock > PCMCIA_MAX_SOCK) return -1;
-
- pcr = au_readl(PB1000_PCR);
-
- if (configure->sock == 0) {
- pcr &= ~(PCR_SLOT_0_VCC0 | PCR_SLOT_0_VCC1 |
- PCR_SLOT_0_VPP0 | PCR_SLOT_0_VPP1);
- }
- else {
- pcr &= ~(PCR_SLOT_1_VCC0 | PCR_SLOT_1_VCC1 |
- PCR_SLOT_1_VPP0 | PCR_SLOT_1_VPP1);
- }
-
- pcr &= ~PCR_SLOT_0_RST;
- debug("Vcc %dV Vpp %dV, pcr %x\n",
- configure->vcc, configure->vpp, pcr);
- switch(configure->vcc){
- case 0: /* Vcc 0 */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_GND,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_12V,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_5V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 50: /* Vcc 5V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_GND,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_5V,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_12V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_5V,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 33: /* Vcc 3.3V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_GND,
- configure->sock);
- break;
- case 50:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_5V,
- configure->sock);
- break;
- case 12:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_12V,
- configure->sock);
- break;
- case 33:
- pcr |= SET_VCC_VPP(VCC_3V,VPP_3V,
- configure->sock);
- break;
- default:
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
- configure->sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- default: /* what's this ? */
- pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);
- printk(KERN_ERR "%s: bad Vcc %d\n",
- __func__, configure->vcc);
- break;
- }
-
- if (configure->sock == 0) {
- pcr &= ~(PCR_SLOT_0_RST);
- if (configure->reset)
- pcr |= PCR_SLOT_0_RST;
- }
- else {
- pcr &= ~(PCR_SLOT_1_RST);
- if (configure->reset)
- pcr |= PCR_SLOT_1_RST;
- }
- au_writel(pcr, PB1000_PCR);
- au_sync_delay(300);
-
- return 0;
-}
-
-
-struct pcmcia_low_level pb1x00_pcmcia_ops = {
- pb1x00_pcmcia_init,
- pb1x00_pcmcia_shutdown,
- pb1x00_pcmcia_socket_state,
- pb1x00_pcmcia_get_irq_info,
- pb1x00_pcmcia_configure_socket
-};
projects / mirror_ubuntu-eoan-kernel.git / commitdiff