&mmc1 {
status = "okay";
vmmc-supply = <&v3_3d>;
- vmmc_aux-supply = <&ldo1_reg>;
+ vqmmc-supply = <&ldo1_reg>;
bus-width = <4>;
cd-gpios = <&gpio6 27 0>; /* gpio 219 */
};
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&evm_3v3_sd>;
- vmmc_aux-supply = <&ldo1_reg>;
+ vqmmc-supply = <&ldo1_reg>;
bus-width = <4>;
/*
* SDCD signal is not being used here - using the fact that GPIO mode
};
&mmc1 {
- vmmc_aux-supply = <&vpo_sd_1v8_3v3>;
+ vqmmc-supply = <&vpo_sd_1v8_3v3>;
};
&mmc2 {
};
&mmc1 {
- vmmc_aux-supply = <&ldo1_reg>;
+ vqmmc-supply = <&ldo1_reg>;
};
&mmc1 {
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
bus-width = <8>;
};
&mmc1 {
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
bus-width = <8>;
};
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&wl12xx_vmmc2>;
- vmmc_aux-supply = <&wl12xx_vaux2>;
+ vqmmc-supply = <&wl12xx_vaux2>;
non-removable;
bus-width = <4>;
cap-power-off-card;
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&wl12xx_vmmc2>;
- vmmc_aux-supply = <&wl12xx_vaux2>;
+ vqmmc-supply = <&wl12xx_vaux2>;
non-removable;
bus-width = <4>;
cap-power-off-card;
&mmc1 {
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
bus-width = <8>;
};
&mmc1 {
interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
bus-width = <8>;
};
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&vaux3>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
bus-width = <8>;
non-removable;
no-sdio;
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&w3cbw003c_npoweron>;
- vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
+ vqmmc-supply = <&w3cbw003c_wifi_nreset>;
bus-width = <4>;
cap-sdio-irq;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>;
bus-width = <8>;
};
&mmc1 {
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
&mmc1 {
vmmc-supply = <&vmmc1>;
- vmmc_aux-supply = <&vsim>;
+ vqmmc-supply = <&vsim>;
/*
* S6-3 must be in ON position for 8 bit mode to function
* Else, use 4 bit mode