*/
#include <linux/module.h>
-#include <linux/reboot.h>
#include <linux/clk/at91_pmc.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/system_misc.h>
-#include <mach/at91rm9200.h>
#include <mach/at91_st.h>
-#include <mach/cpu.h>
#include <mach/hardware.h>
-#include "at91_aic.h"
#include "soc.h"
#include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- * Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk udc_clk = {
- .name = "udc_clk",
- .pmc_mask = 1 << AT91RM9200_ID_UDP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
- .name = "ohci_clk",
- .pmc_mask = 1 << AT91RM9200_ID_UHP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ether_clk = {
- .name = "ether_clk",
- .pmc_mask = 1 << AT91RM9200_ID_EMAC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc_clk = {
- .name = "mci_clk",
- .pmc_mask = 1 << AT91RM9200_ID_MCI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
- .name = "twi_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TWI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
- .name = "usart0_clk",
- .pmc_mask = 1 << AT91RM9200_ID_US0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
- .name = "usart1_clk",
- .pmc_mask = 1 << AT91RM9200_ID_US1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
- .name = "usart2_clk",
- .pmc_mask = 1 << AT91RM9200_ID_US2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart3_clk = {
- .name = "usart3_clk",
- .pmc_mask = 1 << AT91RM9200_ID_US3,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi_clk = {
- .name = "spi_clk",
- .pmc_mask = 1 << AT91RM9200_ID_SPI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioA_clk = {
- .name = "pioA_clk",
- .pmc_mask = 1 << AT91RM9200_ID_PIOA,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
- .name = "pioB_clk",
- .pmc_mask = 1 << AT91RM9200_ID_PIOB,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioC_clk = {
- .name = "pioC_clk",
- .pmc_mask = 1 << AT91RM9200_ID_PIOC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioD_clk = {
- .name = "pioD_clk",
- .pmc_mask = 1 << AT91RM9200_ID_PIOD,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
- .name = "ssc0_clk",
- .pmc_mask = 1 << AT91RM9200_ID_SSC0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
- .name = "ssc1_clk",
- .pmc_mask = 1 << AT91RM9200_ID_SSC1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc2_clk = {
- .name = "ssc2_clk",
- .pmc_mask = 1 << AT91RM9200_ID_SSC2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc0_clk = {
- .name = "tc0_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TC0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc1_clk = {
- .name = "tc1_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TC1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc2_clk = {
- .name = "tc2_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TC2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc3_clk = {
- .name = "tc3_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TC3,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc4_clk = {
- .name = "tc4_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TC4,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc5_clk = {
- .name = "tc5_clk",
- .pmc_mask = 1 << AT91RM9200_ID_TC5,
- .type = CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
- &pioA_clk,
- &pioB_clk,
- &pioC_clk,
- &pioD_clk,
- &usart0_clk,
- &usart1_clk,
- &usart2_clk,
- &usart3_clk,
- &mmc_clk,
- &udc_clk,
- &twi_clk,
- &spi_clk,
- &ssc0_clk,
- &ssc1_clk,
- &ssc2_clk,
- &tc0_clk,
- &tc1_clk,
- &tc2_clk,
- &tc3_clk,
- &tc4_clk,
- &tc5_clk,
- &ohci_clk,
- ðer_clk,
- // irq0 .. irq6
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
- CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
- CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
- CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
- CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.1", &tc3_clk),
- CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk),
- CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.2", &ssc2_clk),
- CLKDEV_CON_DEV_ID("pclk", "fffd0000.ssc", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "fffd4000.ssc", &ssc1_clk),
- CLKDEV_CON_DEV_ID("pclk", "fffd8000.ssc", &ssc2_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91rm9200.0", &twi_clk),
- /* fake hclk clock */
- CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
- CLKDEV_CON_ID("pioA", &pioA_clk),
- CLKDEV_CON_ID("pioB", &pioB_clk),
- CLKDEV_CON_ID("pioC", &pioC_clk),
- CLKDEV_CON_ID("pioD", &pioD_clk),
- /* usart lookup table for DT entries */
- CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
- CLKDEV_CON_DEV_ID("usart", "fffc0000.serial", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "fffc4000.serial", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "fffc8000.serial", &usart2_clk),
- CLKDEV_CON_DEV_ID("usart", "fffcc000.serial", &usart3_clk),
- /* tc lookup table for DT entries */
- CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
- CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
- CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
- CLKDEV_CON_DEV_ID("t0_clk", "fffa4000.timer", &tc3_clk),
- CLKDEV_CON_DEV_ID("t1_clk", "fffa4000.timer", &tc4_clk),
- CLKDEV_CON_DEV_ID("t2_clk", "fffa4000.timer", &tc5_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "fffb4000.mmc", &mmc_clk),
- CLKDEV_CON_DEV_ID("emac_clk", "fffbc000.ethernet", ðer_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffb8000.i2c", &twi_clk),
- CLKDEV_CON_DEV_ID("hclk", "300000.ohci", &ohci_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioD_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
- .name = "pck0",
- .pmc_mask = AT91_PMC_PCK0,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 0,
-};
-static struct clk pck1 = {
- .name = "pck1",
- .pmc_mask = AT91_PMC_PCK1,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 1,
-};
-static struct clk pck2 = {
- .name = "pck2",
- .pmc_mask = AT91_PMC_PCK2,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 2,
-};
-static struct clk pck3 = {
- .name = "pck3",
- .pmc_mask = AT91_PMC_PCK3,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 3,
-};
-
-static void __init at91rm9200_register_clocks(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
- clk_register(periph_clocks[i]);
-
- clkdev_add_table(periph_clocks_lookups,
- ARRAY_SIZE(periph_clocks_lookups));
- clkdev_add_table(usart_clocks_lookups,
- ARRAY_SIZE(usart_clocks_lookups));
-
- clk_register(&pck0);
- clk_register(&pck1);
- clk_register(&pck2);
- clk_register(&pck3);
-}
-#else
-#define at91rm9200_register_clocks NULL
-#endif
-
-/* --------------------------------------------------------------------
- * GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91rm9200_gpio[] __initdata = {
- {
- .id = AT91RM9200_ID_PIOA,
- .regbase = AT91RM9200_BASE_PIOA,
- }, {
- .id = AT91RM9200_ID_PIOB,
- .regbase = AT91RM9200_BASE_PIOB,
- }, {
- .id = AT91RM9200_ID_PIOC,
- .regbase = AT91RM9200_BASE_PIOC,
- }, {
- .id = AT91RM9200_ID_PIOD,
- .regbase = AT91RM9200_BASE_PIOD,
- }
-};
static void at91rm9200_idle(void)
{
at91_init_sram(0, AT91RM9200_SRAM_BASE, AT91RM9200_SRAM_SIZE);
}
-static void __init at91rm9200_ioremap_registers(void)
-{
- at91rm9200_ioremap_st(AT91RM9200_BASE_ST);
- at91_ioremap_ramc(0, AT91RM9200_BASE_MC, 256);
- at91_pm_set_standby(at91rm9200_standby);
-}
-
static void __init at91rm9200_initialize(void)
{
arm_pm_idle = at91rm9200_idle;
arm_pm_restart = at91rm9200_restart;
-
- /* Initialize GPIO subsystem */
- at91_gpio_init(at91rm9200_gpio,
- cpu_is_at91rm9200_bga() ? AT91RM9200_BGA : AT91RM9200_PQFP);
}
-/* --------------------------------------------------------------------
- * Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
- 1, /* Parallel IO Controller A */
- 1, /* Parallel IO Controller B */
- 1, /* Parallel IO Controller C */
- 1, /* Parallel IO Controller D */
- 5, /* USART 0 */
- 5, /* USART 1 */
- 5, /* USART 2 */
- 5, /* USART 3 */
- 0, /* Multimedia Card Interface */
- 2, /* USB Device Port */
- 6, /* Two-Wire Interface */
- 5, /* Serial Peripheral Interface */
- 4, /* Serial Synchronous Controller 0 */
- 4, /* Serial Synchronous Controller 1 */
- 4, /* Serial Synchronous Controller 2 */
- 0, /* Timer Counter 0 */
- 0, /* Timer Counter 1 */
- 0, /* Timer Counter 2 */
- 0, /* Timer Counter 3 */
- 0, /* Timer Counter 4 */
- 0, /* Timer Counter 5 */
- 2, /* USB Host port */
- 3, /* Ethernet MAC */
- 0, /* Advanced Interrupt Controller (IRQ0) */
- 0, /* Advanced Interrupt Controller (IRQ1) */
- 0, /* Advanced Interrupt Controller (IRQ2) */
- 0, /* Advanced Interrupt Controller (IRQ3) */
- 0, /* Advanced Interrupt Controller (IRQ4) */
- 0, /* Advanced Interrupt Controller (IRQ5) */
- 0 /* Advanced Interrupt Controller (IRQ6) */
-};
-
AT91_SOC_START(at91rm9200)
.map_io = at91rm9200_map_io,
- .default_irq_priority = at91rm9200_default_irq_priority,
- .extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1)
- | (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3)
- | (1 << AT91RM9200_ID_IRQ4) | (1 << AT91RM9200_ID_IRQ5)
- | (1 << AT91RM9200_ID_IRQ6),
- .ioremap_registers = at91rm9200_ioremap_registers,
- .register_clocks = at91rm9200_register_clocks,
.init = at91rm9200_initialize,
AT91_SOC_END
+++ /dev/null
-/*
- * arch/arm/mach-at91/at91rm9200_devices.c
- *
- * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- * Copyright (C) 2005 David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <mach/at91rm9200.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-/* --------------------------------------------------------------------
- * USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
- [0] = {
- .start = AT91RM9200_UHP_BASE,
- .end = AT91RM9200_UHP_BASE + SZ_1M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_UHP,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_UHP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_usbh_device = {
- .name = "at91_ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &usbh_data,
- },
- .resource = usbh_resources,
- .num_resources = ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
- int i;
-
- if (!data)
- return;
-
- /* Enable overcurrent notification */
- for (i = 0; i < data->ports; i++) {
- if (gpio_is_valid(data->overcurrent_pin[i]))
- at91_set_gpio_input(data->overcurrent_pin[i], 1);
- }
-
- usbh_data = *data;
- platform_device_register(&at91rm9200_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_UDP,
- .end = AT91RM9200_BASE_UDP + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_UDP,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_UDP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_udc_device = {
- .name = "at91_udc",
- .id = -1,
- .dev = {
- .platform_data = &udc_data,
- },
- .resource = udc_resources,
- .num_resources = ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->vbus_pin)) {
- at91_set_gpio_input(data->vbus_pin, 0);
- at91_set_deglitch(data->vbus_pin, 1);
- }
- if (gpio_is_valid(data->pullup_pin))
- at91_set_gpio_output(data->pullup_pin, 0);
-
- udc_data = *data;
- platform_device_register(&at91rm9200_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_EMAC,
- .end = AT91RM9200_BASE_EMAC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_EMAC,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_EMAC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_eth_device = {
- .name = "at91_ether",
- .id = -1,
- .dev = {
- .dma_mask = ð_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = ð_data,
- },
- .resource = eth_resources,
- .num_resources = ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->phy_irq_pin)) {
- at91_set_gpio_input(data->phy_irq_pin, 0);
- at91_set_deglitch(data->phy_irq_pin, 1);
- }
-
- /* Pins used for MII and RMII */
- at91_set_A_periph(AT91_PIN_PA16, 0); /* EMDIO */
- at91_set_A_periph(AT91_PIN_PA15, 0); /* EMDC */
- at91_set_A_periph(AT91_PIN_PA14, 0); /* ERXER */
- at91_set_A_periph(AT91_PIN_PA13, 0); /* ERX1 */
- at91_set_A_periph(AT91_PIN_PA12, 0); /* ERX0 */
- at91_set_A_periph(AT91_PIN_PA11, 0); /* ECRS_ECRSDV */
- at91_set_A_periph(AT91_PIN_PA10, 0); /* ETX1 */
- at91_set_A_periph(AT91_PIN_PA9, 0); /* ETX0 */
- at91_set_A_periph(AT91_PIN_PA8, 0); /* ETXEN */
- at91_set_A_periph(AT91_PIN_PA7, 0); /* ETXCK_EREFCK */
-
- if (!data->is_rmii) {
- at91_set_B_periph(AT91_PIN_PB19, 0); /* ERXCK */
- at91_set_B_periph(AT91_PIN_PB18, 0); /* ECOL */
- at91_set_B_periph(AT91_PIN_PB17, 0); /* ERXDV */
- at91_set_B_periph(AT91_PIN_PB16, 0); /* ERX3 */
- at91_set_B_periph(AT91_PIN_PB15, 0); /* ERX2 */
- at91_set_B_periph(AT91_PIN_PB14, 0); /* ETXER */
- at91_set_B_periph(AT91_PIN_PB13, 0); /* ETX3 */
- at91_set_B_periph(AT91_PIN_PB12, 0); /* ETX2 */
- }
-
- eth_data = *data;
- platform_device_register(&at91rm9200_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Compact Flash / PCMCIA
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
-static struct at91_cf_data cf_data;
-
-#define CF_BASE AT91_CHIPSELECT_4
-
-static struct resource cf_resources[] = {
- [0] = {
- .start = CF_BASE,
- /* ties up CS4, CS5 and CS6 */
- .end = CF_BASE + (0x30000000 - 1),
- .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
- },
-};
-
-static struct platform_device at91rm9200_cf_device = {
- .name = "at91_cf",
- .id = -1,
- .dev = {
- .platform_data = &cf_data,
- },
- .resource = cf_resources,
- .num_resources = ARRAY_SIZE(cf_resources),
-};
-
-void __init at91_add_device_cf(struct at91_cf_data *data)
-{
- unsigned int csa;
-
- if (!data)
- return;
-
- data->chipselect = 4; /* can only use EBI ChipSelect 4 */
-
- /* CF takes over CS4, CS5, CS6 */
- csa = at91_ramc_read(0, AT91_EBI_CSA);
- at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS4A_SMC_COMPACTFLASH);
-
- /*
- * Static memory controller timing adjustments.
- * REVISIT: these timings are in terms of MCK cycles, so
- * when MCK changes (cpufreq etc) so must these values...
- */
- at91_ramc_write(0, AT91_SMC_CSR(4),
- AT91_SMC_ACSS_STD
- | AT91_SMC_DBW_16
- | AT91_SMC_BAT
- | AT91_SMC_WSEN
- | AT91_SMC_NWS_(32) /* wait states */
- | AT91_SMC_RWSETUP_(6) /* setup time */
- | AT91_SMC_RWHOLD_(4) /* hold time */
- );
-
- /* input/irq */
- if (gpio_is_valid(data->irq_pin)) {
- at91_set_gpio_input(data->irq_pin, 1);
- at91_set_deglitch(data->irq_pin, 1);
- }
- at91_set_gpio_input(data->det_pin, 1);
- at91_set_deglitch(data->det_pin, 1);
-
- /* outputs, initially off */
- if (gpio_is_valid(data->vcc_pin))
- at91_set_gpio_output(data->vcc_pin, 0);
- at91_set_gpio_output(data->rst_pin, 0);
-
- /* force poweron defaults for these pins ... */
- at91_set_A_periph(AT91_PIN_PC9, 0); /* A25/CFRNW */
- at91_set_A_periph(AT91_PIN_PC10, 0); /* NCS4/CFCS */
- at91_set_A_periph(AT91_PIN_PC11, 0); /* NCS5/CFCE1 */
- at91_set_A_periph(AT91_PIN_PC12, 0); /* NCS6/CFCE2 */
-
- /* nWAIT is _not_ a default setting */
- at91_set_A_periph(AT91_PIN_PC6, 1); /* nWAIT */
-
- cf_data = *data;
- platform_device_register(&at91rm9200_cf_device);
-}
-#else
-void __init at91_add_device_cf(struct at91_cf_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * MMC / SD
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc_data;
-
-static struct resource mmc_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_MCI,
- .end = AT91RM9200_BASE_MCI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_MCI,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_MCI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_mmc_device = {
- .name = "atmel_mci",
- .id = -1,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc_data,
- },
- .resource = mmc_resources,
- .num_resources = ARRAY_SIZE(mmc_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
- unsigned int i;
- unsigned int slot_count = 0;
-
- if (!data)
- return;
-
- for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
-
- if (!data->slot[i].bus_width)
- continue;
-
- /* input/irq */
- if (gpio_is_valid(data->slot[i].detect_pin)) {
- at91_set_gpio_input(data->slot[i].detect_pin, 1);
- at91_set_deglitch(data->slot[i].detect_pin, 1);
- }
- if (gpio_is_valid(data->slot[i].wp_pin))
- at91_set_gpio_input(data->slot[i].wp_pin, 1);
-
- switch (i) {
- case 0: /* slot A */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA28, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA29, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_B_periph(AT91_PIN_PB3, 1);
- at91_set_B_periph(AT91_PIN_PB4, 1);
- at91_set_B_periph(AT91_PIN_PB5, 1);
- }
- slot_count++;
- break;
- case 1: /* slot B */
- /* CMD */
- at91_set_B_periph(AT91_PIN_PA8, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_B_periph(AT91_PIN_PA9, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_B_periph(AT91_PIN_PA10, 1);
- at91_set_B_periph(AT91_PIN_PA11, 1);
- at91_set_B_periph(AT91_PIN_PA12, 1);
- }
- slot_count++;
- break;
- default:
- printk(KERN_ERR
- "AT91: SD/MMC slot %d not available\n", i);
- break;
- }
- if (slot_count) {
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA27, 0);
-
- mmc_data = *data;
- platform_device_register(&at91rm9200_mmc_device);
- }
- }
-
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
- {
- .start = NAND_BASE,
- .end = NAND_BASE + SZ_256M - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91rm9200_nand_device = {
- .name = "atmel_nand",
- .id = -1,
- .dev = {
- .platform_data = &nand_data,
- },
- .resource = nand_resources,
- .num_resources = ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
- unsigned int csa;
-
- if (!data)
- return;
-
- /* enable the address range of CS3 */
- csa = at91_ramc_read(0, AT91_EBI_CSA);
- at91_ramc_write(0, AT91_EBI_CSA, csa | AT91_EBI_CS3A_SMC_SMARTMEDIA);
-
- /* set the bus interface characteristics */
- at91_ramc_write(0, AT91_SMC_CSR(3), AT91_SMC_ACSS_STD | AT91_SMC_DBW_8 | AT91_SMC_WSEN
- | AT91_SMC_NWS_(5)
- | AT91_SMC_TDF_(1)
- | AT91_SMC_RWSETUP_(0) /* tDS Data Set up Time 30 - ns */
- | AT91_SMC_RWHOLD_(1) /* tDH Data Hold Time 20 - ns */
- );
-
- /* enable pin */
- if (gpio_is_valid(data->enable_pin))
- at91_set_gpio_output(data->enable_pin, 1);
-
- /* ready/busy pin */
- if (gpio_is_valid(data->rdy_pin))
- at91_set_gpio_input(data->rdy_pin, 1);
-
- /* card detect pin */
- if (gpio_is_valid(data->det_pin))
- at91_set_gpio_input(data->det_pin, 1);
-
- at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */
- at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */
-
- nand_data = *data;
- platform_device_register(&at91rm9200_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
- .sda_pin = AT91_PIN_PA25,
- .sda_is_open_drain = 1,
- .scl_pin = AT91_PIN_PA26,
- .scl_is_open_drain = 1,
- .udelay = 2, /* ~100 kHz */
-};
-
-static struct platform_device at91rm9200_twi_device = {
- .name = "i2c-gpio",
- .id = 0,
- .dev.platform_data = &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- at91_set_GPIO_periph(AT91_PIN_PA25, 1); /* TWD (SDA) */
- at91_set_multi_drive(AT91_PIN_PA25, 1);
-
- at91_set_GPIO_periph(AT91_PIN_PA26, 1); /* TWCK (SCL) */
- at91_set_multi_drive(AT91_PIN_PA26, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91rm9200_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_TWI,
- .end = AT91RM9200_BASE_TWI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TWI,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_twi_device = {
- .name = "i2c-at91rm9200",
- .id = 0,
- .resource = twi_resources,
- .num_resources = ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- /* pins used for TWI interface */
- at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */
- at91_set_multi_drive(AT91_PIN_PA25, 1);
-
- at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */
- at91_set_multi_drive(AT91_PIN_PA26, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91rm9200_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_SPI,
- .end = AT91RM9200_BASE_SPI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_SPI,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_SPI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_spi_device = {
- .name = "atmel_spi",
- .id = 0,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi_resources,
- .num_resources = ARRAY_SIZE(spi_resources),
-};
-
-static const unsigned spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
- int i;
- unsigned long cs_pin;
-
- at91_set_A_periph(AT91_PIN_PA0, 0); /* MISO */
- at91_set_A_periph(AT91_PIN_PA1, 0); /* MOSI */
- at91_set_A_periph(AT91_PIN_PA2, 0); /* SPCK */
-
- /* Enable SPI chip-selects */
- for (i = 0; i < nr_devices; i++) {
- if (devices[i].controller_data)
- cs_pin = (unsigned long) devices[i].controller_data;
- else
- cs_pin = spi_standard_cs[devices[i].chip_select];
-
- if (devices[i].chip_select == 0) /* for CS0 errata */
- at91_set_A_periph(cs_pin, 0);
- else
- at91_set_gpio_output(cs_pin, 1);
-
-
- /* pass chip-select pin to driver */
- devices[i].controller_data = (void *) cs_pin;
- }
-
- spi_register_board_info(devices, nr_devices);
- platform_device_register(&at91rm9200_spi_device);
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Timer/Counter blocks
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb0_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_TCB0,
- .end = AT91RM9200_BASE_TCB0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC0,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC0,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC1,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC1,
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC2,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_tcb0_device = {
- .name = "atmel_tcb",
- .id = 0,
- .resource = tcb0_resources,
- .num_resources = ARRAY_SIZE(tcb0_resources),
-};
-
-static struct resource tcb1_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_TCB1,
- .end = AT91RM9200_BASE_TCB1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC3,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC3,
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC4,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC4,
- .flags = IORESOURCE_IRQ,
- },
- [3] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_TC5,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_TC5,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_tcb1_device = {
- .name = "atmel_tcb",
- .id = 1,
- .resource = tcb1_resources,
- .num_resources = ARRAY_SIZE(tcb1_resources),
-};
-
-static void __init at91_add_device_tc(void)
-{
- platform_device_register(&at91rm9200_tcb0_device);
- platform_device_register(&at91rm9200_tcb1_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- * RTC
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
-static struct resource rtc_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_RTC,
- .end = AT91RM9200_BASE_RTC + SZ_256 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91_ID_SYS,
- .end = NR_IRQS_LEGACY + AT91_ID_SYS,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_rtc_device = {
- .name = "at91_rtc",
- .id = -1,
- .resource = rtc_resources,
- .num_resources = ARRAY_SIZE(rtc_resources),
-};
-
-static void __init at91_add_device_rtc(void)
-{
- platform_device_register(&at91rm9200_rtc_device);
-}
-#else
-static void __init at91_add_device_rtc(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91RM9200_WATCHDOG) || defined(CONFIG_AT91RM9200_WATCHDOG_MODULE)
-static struct platform_device at91rm9200_wdt_device = {
- .name = "at91_wdt",
- .id = -1,
- .num_resources = 0,
-};
-
-static void __init at91_add_device_watchdog(void)
-{
- platform_device_register(&at91rm9200_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_SSC0,
- .end = AT91RM9200_BASE_SSC0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_SSC0,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_SSC0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_ssc0_device = {
- .name = "at91rm9200_ssc",
- .id = 0,
- .dev = {
- .dma_mask = &ssc0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc0_resources,
- .num_resources = ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB0, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB1, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB2, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB3, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB4, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB5, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_SSC1,
- .end = AT91RM9200_BASE_SSC1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_SSC1,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_SSC1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_ssc1_device = {
- .name = "at91rm9200_ssc",
- .id = 1,
- .dev = {
- .dma_mask = &ssc1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc1_resources,
- .num_resources = ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB6, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB7, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB8, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB9, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB10, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB11, 1);
-}
-
-static u64 ssc2_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc2_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_SSC2,
- .end = AT91RM9200_BASE_SSC2 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_SSC2,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_SSC2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91rm9200_ssc2_device = {
- .name = "at91rm9200_ssc",
- .id = 2,
- .dev = {
- .dma_mask = &ssc2_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc2_resources,
- .num_resources = ARRAY_SIZE(ssc2_resources),
-};
-
-static inline void configure_ssc2_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB12, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB13, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB14, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB15, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB16, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB17, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver. For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
- struct platform_device *pdev;
-
- /*
- * NOTE: caller is responsible for passing information matching
- * "pins" to whatever will be using each particular controller.
- */
- switch (id) {
- case AT91RM9200_ID_SSC0:
- pdev = &at91rm9200_ssc0_device;
- configure_ssc0_pins(pins);
- break;
- case AT91RM9200_ID_SSC1:
- pdev = &at91rm9200_ssc1_device;
- configure_ssc1_pins(pins);
- break;
- case AT91RM9200_ID_SSC2:
- pdev = &at91rm9200_ssc2_device;
- configure_ssc2_pins(pins);
- break;
- default:
- return;
- }
-
- platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-static struct resource dbgu_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_DBGU,
- .end = AT91RM9200_BASE_DBGU + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91_ID_SYS,
- .end = NR_IRQS_LEGACY + AT91_ID_SYS,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data dbgu_data = {
- .use_dma_tx = 0,
- .use_dma_rx = 0, /* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_dbgu_device = {
- .name = "atmel_usart",
- .id = 0,
- .dev = {
- .dma_mask = &dbgu_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &dbgu_data,
- },
- .resource = dbgu_resources,
- .num_resources = ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
- at91_set_A_periph(AT91_PIN_PA30, 0); /* DRXD */
- at91_set_A_periph(AT91_PIN_PA31, 1); /* DTXD */
-}
-
-static struct resource uart0_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_US0,
- .end = AT91RM9200_BASE_US0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_US0,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_US0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart0_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static struct gpiod_lookup_table uart0_gpios_table = {
- .dev_id = "atmel_usart",
- .table = {
- GPIO_LOOKUP("pioA", 21, "rts", GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart0_device = {
- .name = "atmel_usart",
- .id = 1,
- .dev = {
- .dma_mask = &uart0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart0_data,
- },
- .resource = uart0_resources,
- .num_resources = ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */
- at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */
-
- if (pins & ATMEL_UART_CTS)
- at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */
-
- if (pins & ATMEL_UART_RTS) {
- /*
- * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
- * We need to drive the pin manually. The serial driver will driver
- * this to high when initializing.
- */
- gpiod_add_lookup_table(&uart0_gpios_table);
- }
-}
-
-static struct resource uart1_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_US1,
- .end = AT91RM9200_BASE_US1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_US1,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_US1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart1_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart1_device = {
- .name = "atmel_usart",
- .id = 2,
- .dev = {
- .dma_mask = &uart1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart1_data,
- },
- .resource = uart1_resources,
- .num_resources = ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */
- at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */
-
- if (pins & ATMEL_UART_RI)
- at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */
- if (pins & ATMEL_UART_DTR)
- at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */
- if (pins & ATMEL_UART_DCD)
- at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */
- if (pins & ATMEL_UART_CTS)
- at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */
- if (pins & ATMEL_UART_DSR)
- at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */
- if (pins & ATMEL_UART_RTS)
- at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */
-}
-
-static struct resource uart2_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_US2,
- .end = AT91RM9200_BASE_US2 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_US2,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_US2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart2_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart2_device = {
- .name = "atmel_usart",
- .id = 3,
- .dev = {
- .dma_mask = &uart2_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart2_data,
- },
- .resource = uart2_resources,
- .num_resources = ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */
- at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */
-
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PA30, 0); /* CTS2 */
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PA31, 0); /* RTS2 */
-}
-
-static struct resource uart3_resources[] = {
- [0] = {
- .start = AT91RM9200_BASE_US3,
- .end = AT91RM9200_BASE_US3 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91RM9200_ID_US3,
- .end = NR_IRQS_LEGACY + AT91RM9200_ID_US3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart3_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart3_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91rm9200_uart3_device = {
- .name = "atmel_usart",
- .id = 4,
- .dev = {
- .dma_mask = &uart3_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart3_data,
- },
- .resource = uart3_resources,
- .num_resources = ARRAY_SIZE(uart3_resources),
-};
-
-static inline void configure_usart3_pins(unsigned pins)
-{
- at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */
- at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */
-
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PB1, 0); /* CTS3 */
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PB0, 0); /* RTS3 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
- struct platform_device *pdev;
- struct atmel_uart_data *pdata;
-
- switch (id) {
- case 0: /* DBGU */
- pdev = &at91rm9200_dbgu_device;
- configure_dbgu_pins();
- break;
- case AT91RM9200_ID_US0:
- pdev = &at91rm9200_uart0_device;
- configure_usart0_pins(pins);
- break;
- case AT91RM9200_ID_US1:
- pdev = &at91rm9200_uart1_device;
- configure_usart1_pins(pins);
- break;
- case AT91RM9200_ID_US2:
- pdev = &at91rm9200_uart2_device;
- configure_usart2_pins(pins);
- break;
- case AT91RM9200_ID_US3:
- pdev = &at91rm9200_uart3_device;
- configure_usart3_pins(pins);
- break;
- default:
- return;
- }
- pdata = pdev->dev.platform_data;
- pdata->num = portnr; /* update to mapped ID */
-
- if (portnr < ATMEL_MAX_UART)
- at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
- int i;
-
- for (i = 0; i < ATMEL_MAX_UART; i++) {
- if (at91_uarts[i])
- platform_device_register(at91_uarts[i]);
- }
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
- at91_add_device_rtc();
- at91_add_device_watchdog();
- at91_add_device_tc();
- return 0;
-}
-
-arch_initcall(at91_add_standard_devices);
projects / mirror_ubuntu-artful-kernel.git / commitdiff