#define MC1 0x02 /* DMA"C" timing */
#define MC0 0x01 /* DMA"C" timing */
-#if 0
- unsigned long bibma = pci_resource_start(dev, 4);
- u8 hi = 0, lo = 0;
-
- u8 sc1c = inb_p((u16)bibma + 0x1c);
- u8 sc1e = inb_p((u16)bibma + 0x1e);
- u8 sc1f = inb_p((u16)bibma + 0x1f);
-
- p += sprintf(p, "Host Mode : %s\n",
- (sc1f & 0x08) ? "Tri-Stated" : "Normal");
- p += sprintf(p, "Bus Clocking : %s\n",
- ((sc1f & 0xC0) == 0xC0) ? "100 External" :
- ((sc1f & 0x80) == 0x80) ? "66 External" :
- ((sc1f & 0x40) == 0x40) ? "33 External" : "33 PCI Internal");
- p += sprintf(p, "IO pad select : %s mA\n",
- ((sc1c & 0x03) == 0x03) ? "10" :
- ((sc1c & 0x02) == 0x02) ? "8" :
- ((sc1c & 0x01) == 0x01) ? "6" :
- ((sc1c & 0x00) == 0x00) ? "4" : "??");
- hi = sc1e >> 4;
- lo = sc1e & 0xf;
- p += sprintf(p, "Status Polling Period : %d\n", hi);
- p += sprintf(p, "Interrupt Check Status Polling Delay : %d\n", lo);
-#endif
-
static u8 pdc202xx_ratemask (ide_drive_t *drive)
{
u8 mode;
pdc202xx_reset_host(hwif);
pdc202xx_reset_host(mate);
-#if 0
- /*
- * FIXME: Have to kick all the drives again :-/
- * What a pain in the ACE!
- */
- if (hwif->present) {
- u16 hunit = 0;
- for (hunit = 0; hunit < MAX_DRIVES; ++hunit) {
- ide_drive_t *hdrive = &hwif->drives[hunit];
- if (hdrive->present) {
- if (hwif->ide_dma_check)
- hwif->ide_dma_check(hdrive);
- else
- hwif->tuneproc(hdrive, 5);
- }
- }
- }
- if (mate->present) {
- u16 munit = 0;
- for (munit = 0; munit < MAX_DRIVES; ++munit) {
- ide_drive_t *mdrive = &mate->drives[munit];
- if (mdrive->present) {
- if (mate->ide_dma_check)
- mate->ide_dma_check(mdrive);
- else
- mate->tuneproc(mdrive, 5);
- }
- }
- }
-#else
hwif->tuneproc(drive, 5);
-#endif
}
-static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev, const char *name)
+static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev,
+ const char *name)
{
+ /* This doesn't appear needed */
if (dev->resource[PCI_ROM_RESOURCE].start) {
pci_write_config_dword(dev, PCI_ROM_ADDRESS,
dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
name, dev->resource[PCI_ROM_RESOURCE].start);
}
- /*
- * software reset - this is required because the bios
- * will set UDMA timing on if the hdd supports it. The
- * user may want to turn udma off. A bug in the pdc20262
- * is that it cannot handle a downgrade in timing from
- * UDMA to DMA. Disk accesses after issuing a set
- * feature command will result in errors. A software
- * reset leaves the timing registers intact,
- * but resets the drives.
- */
-#if 0
- if ((dev->device == PCI_DEVICE_ID_PROMISE_20267) ||
- (dev->device == PCI_DEVICE_ID_PROMISE_20265) ||
- (dev->device == PCI_DEVICE_ID_PROMISE_20263) ||
- (dev->device == PCI_DEVICE_ID_PROMISE_20262)) {
- unsigned long high_16 = pci_resource_start(dev, 4);
- byte udma_speed_flag = inb(high_16 + 0x001f);
- outb(udma_speed_flag | 0x10, high_16 + 0x001f);
- mdelay(100);
- outb(udma_speed_flag & ~0x10, high_16 + 0x001f);
- mdelay(2000); /* 2 seconds ?! */
- }
-
-#endif
return dev->irq;
}
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
+ hwif->err_stops_fifo = 1;
+
hwif->ide_dma_check = &pdc202xx_config_drive_xfer_rate;
hwif->ide_dma_lostirq = &pdc202xx_ide_dma_lostirq;
hwif->ide_dma_timeout = &pdc202xx_ide_dma_timeout;
"mirror fixed.\n", d->name);
}
}
-
-#if 0
- if (dev->device == PCI_DEVICE_ID_PROMISE_20262)
- if (e->reg && (pci_read_config_byte(dev, e->reg, &tmp) ||
- (tmp & e->mask) != e->val))
-
- if (d->enablebits[0].reg != d->enablebits[1].reg) {
- d->enablebits[0].reg = d->enablebits[1].reg;
- d->enablebits[0].mask = d->enablebits[1].mask;
- d->enablebits[0].val = d->enablebits[1].val;
- }
-#endif
-
return ide_setup_pci_device(dev, d);
}
"attached to I2O RAID controller.\n");
return -ENODEV;
}
-
-#if 0
- {
- u8 pri = 0, sec = 0;
-
- if (e->reg && (pci_read_config_byte(dev, e->reg, &tmp) ||
- (tmp & e->mask) != e->val))
-
- if (d->enablebits[0].reg != d->enablebits[1].reg) {
- d->enablebits[0].reg = d->enablebits[1].reg;
- d->enablebits[0].mask = d->enablebits[1].mask;
- d->enablebits[0].val = d->enablebits[1].val;
- }
- }
-#endif
-
return ide_setup_pci_device(dev, d);
}