- syscon: some subnode of the RealView SoC node must be a
system controller node pointing to the control registers,
- with the compatible string set to one of these tuples:
+ with the compatible string set to one of these:
+ "arm,realview-eb11mp-revb-syscon", "arm,realview-eb-syscon", "syscon"
+ "arm,realview-eb11mp-revc-syscon", "arm,realview-eb-syscon", "syscon"
"arm,realview-eb-syscon", "syscon"
"arm,realview-pb1176-syscon", "syscon"
"arm,realview-pb11mp-syscon", "syscon"
Required properties (in root node):
compatible = "arm,juno"; /* For Juno r0 board */
compatible = "arm,juno-r1"; /* For Juno r1 board */
+ compatible = "arm,juno-r2"; /* For Juno r2 board */
Required nodes:
The description for the board must include:
"marvell,sheeva-v5"
"nvidia,tegra132-denver"
"qcom,krait"
+ "qcom,kryo"
"qcom,scorpion"
- enable-method
Value type: <stringlist>
Usage: optional
Value type: <prop-encoded-array>
Definition: A u32 value that represents the running time dynamic
- power coefficient in units of mW/MHz/uVolt^2. The
+ power coefficient in units of mW/MHz/uV^2. The
coefficient can either be calculated from power
measurements or derived by analysis.
during suspend.
- ti,no-reset-on-init: When present, the module should not be reset at init
- ti,no-idle-on-init: When present, the module should not be idled at init
+- ti,no-idle: When present, the module is never allowed to idle.
Example:
compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43"
- AM43x EPOS EVM
- compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43"
+ compatible = "ti,am43x-epos-evm", "ti,am43", "ti,am438x"
- AM437x GP EVM
compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43"
* published by the Free Software Foundation.
*/
#include "am33xx.dtsi"
+ #include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Grinn AM335x ChiliSOM";
};
-&tps {
- compatible = "ti,tps65217";
+/include/ "tps65217.dtsi"
+&tps {
regulators {
- #address-cells = <1>;
- #size-cells = <0>;
-
dcdc1_reg: regulator@0 {
- reg = <0>;
regulator-name = "vdds_dpr";
regulator-always-on;
};
dcdc2_reg: regulator@1 {
- reg = <1>;
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
regulator-min-microvolt = <925000>;
};
dcdc3_reg: regulator@2 {
- reg = <2>;
/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
regulator-name = "vdd_core";
regulator-min-microvolt = <925000>;
};
ldo1_reg: regulator@3 {
- reg = <3>;
regulator-name = "vio,vrtc,vdds";
regulator-boot-on;
regulator-always-on;
};
ldo2_reg: regulator@4 {
- reg = <4>;
regulator-name = "vdd_3v3aux";
regulator-boot-on;
regulator-always-on;
};
ldo3_reg: regulator@5 {
- reg = <5>;
regulator-name = "vdd_1v8";
regulator-boot-on;
regulator-always-on;
};
ldo4_reg: regulator@6 {
- reg = <6>;
regulator-name = "vdd_3v3d";
regulator-boot-on;
regulator-always-on;
pinctrl-0 = <&nandflash_pins>;
ranges = <0 0 0x08000000 0x01000000>; /* CS0 0 @addr 0x08000000, size 0x01000000 */
nand@0,0 {
+ compatible = "ti,omap2-nand";
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
gpmc,access-ns = <64>;
gpmc,rd-cycle-ns = <82>;
gpmc,wr-cycle-ns = <82>;
- gpmc,wait-on-read = "true";
- gpmc,wait-on-write = "true";
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,clk-activation-ns = <0>;
- gpmc,wait-monitoring-ns = <0>;
gpmc,wr-access-ns = <40>;
gpmc,wr-data-mux-bus-ns = <0>;
};
};
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
default-brightness-level = <6>;
};
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* audio external oscillator */
+ tlv320aic3x_mclk: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>; /* 24.576MHz */
+ };
+ };
+
sound {
compatible = "ti,da830-evm-audio";
ti,model = "AM335x-SL50";
ti,audio-codec = <&audio_codec>;
ti,mcasp-controller = <&mcasp0>;
- ti,codec-clock-rate = <12000000>;
+
+ clocks = <&tlv320aic3x_mclk>;
+ clock-names = "mclk";
+
ti,audio-routing =
"Headphone Jack", "HPLOUT",
"Headphone Jack", "HPROUT",
AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr0.mcasp0_axr0 */
- AM33XX_IOPAD(0x99c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+ AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2 */
>;
};
pinctrl-0 = <&uart4_pins>;
};
+#include "tps65217.dtsi"
+
&tps {
- compatible = "ti,tps65217";
ti,pmic-shutdown-controller;
interrupt-parent = <&intc>;
interrupts = <7>; /* NNMI */
regulators {
- #address-cells = <1>;
- #size-cells = <0>;
-
dcdc1_reg: regulator@0 {
- reg = <0>;
/* VDDS_DDR */
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
};
dcdc2_reg: regulator@1 {
- reg = <1>;
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
regulator-min-microvolt = <925000>;
};
dcdc3_reg: regulator@2 {
- reg = <2>;
/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
regulator-name = "vdd_core";
regulator-min-microvolt = <925000>;
};
ldo1_reg: regulator@3 {
- reg = <3>;
/* VRTC / VIO / VDDS*/
regulator-always-on;
regulator-min-microvolt = <1800000>;
};
ldo2_reg: regulator@4 {
- reg = <4>;
/* VDD_3V3AUX */
regulator-always-on;
regulator-min-microvolt = <3300000>;
};
ldo3_reg: regulator@5 {
- reg = <5>;
/* VDD_1V8 */
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ldo4_reg: regulator@6 {
- reg = <6>;
/* VDD_3V3A */
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
memory {
device_type = "memory";
- reg = <0x80000000 0x80000000>;
+ reg = <0x0 0x80000000 0x0 0x80000000>;
};
vdd_3v3: fixedregulator-vdd_3v3 {
sound0_master: simple-audio-card,codec {
sound-dai = <&tlv320aic3104>;
+ assigned-clocks = <&clkoutmux2_clk_mux>;
+ assigned-clock-parents = <&sys_clk2_dclk_div>;
clocks = <&clkout2_clk>;
};
};
extcon_usb2: tps659038_usb {
compatible = "ti,palmas-usb-vid";
ti,enable-vbus-detection;
- ti,enable-id-detection;
- id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>;
+ vbus-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
};
};
DRVDD-supply = <&vdd_3v3>;
DVDD-supply = <&aic_dvdd>;
};
+
+ eeprom: eeprom@50 {
+ compatible = "at,24c32";
+ reg = <0x50>;
+ };
};
&i2c3 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mcasp3_pins_default>;
pinctrl-1 = <&mcasp3_pins_sleep>;
+ assigned-clocks = <&mcasp3_ahclkx_mux>;
+ assigned-clock-parents = <&sys_clkin2>;
status = "okay";
op-mode = <0>; /* MCASP_IIS_MODE */
memory {
device_type = "memory";
- reg = <0x80000000 0x20000000>; /* 512 MB - minimal configuration */
+ reg = <0x0 0x80000000 0x0 0x20000000>; /* 512 MB - minimal configuration */
};
leds {
ti,debounce-tol = /bits/ 16 <10>;
ti,debounce-rep = /bits/ 16 <1>;
- linux,wakeup;
+ wakeup-source;
};
};
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
- MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
internal-regs {
spi1: spi@10680 {
};
};
+ /* CON3 */
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <1>;
+ bm,pool-short = <3>;
};
+ /* CON2 */
ethernet@34000 {
status = "okay";
phy = <&phy1>;
phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <2>;
+ bm,pool-short = <3>;
};
+ /* CON4 */
ethernet@70000 {
pinctrl-names = "default";
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
+ buffer-manager = <&bm>;
+ bm,pool-long = <0>;
+ bm,pool-short = <3>;
+ };
+
+ bm@c8000 {
+ status = "okay";
};
nfc: flash@d0000 {
};
};
+ bm-bppi {
+ status = "okay";
+ };
+
pcie-controller {
status = "okay";
#include <dt-bindings/gpio/gpio.h>
/ {
- model = "Marvell Armada 385 GP";
- compatible = "marvell,a385-gp", "marvell,armada388", "marvell,armada380";
+ model = "Marvell Armada 388 DB-88F6820-GP";
+ compatible = "marvell,a388-gp", "marvell,armada388", "marvell,armada380";
chosen {
stdout-path = "serial0:115200n8";
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
- MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
internal-regs {
spi@10600 {
status = "okay";
phy = <&phy1>;
phy-mode = "rgmii-id";
+ buffer-manager = <&bm>;
+ bm,pool-long = <2>;
+ bm,pool-short = <3>;
};
/* CON4 */
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
+ buffer-manager = <&bm>;
+ bm,pool-long = <0>;
+ bm,pool-short = <1>;
};
};
};
+ bm@c8000 {
+ status = "okay";
+ };
+
sata@e0000 {
pinctrl-names = "default";
pinctrl-0 = <&sata2_pins>, <&sata3_pins>;
/* CON5 */
usb3@f0000 {
- vcc-supply = <®_usb2_1_vbus>;
+ usb-phy = <&usb2_1_phy>;
status = "okay";
};
/* CON7 */
usb3@f8000 {
- vcc-supply = <®_usb3_vbus>;
+ usb-phy = <&usb3_phy>;
status = "okay";
};
};
+ bm-bppi {
+ status = "okay";
+ };
+
pcie-controller {
status = "okay";
/*
};
};
+ usb2_1_phy: usb2_1_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb2_1_vbus>;
+ };
+
+ usb3_phy: usb3_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb3_vbus>;
+ };
+
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
regulator-name = "usb3-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- regulator-always-on;
gpio = <&expander1 15 GPIO_ACTIVE_HIGH>;
};
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- regulator-always-on;
gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
};
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
enable-active-high;
- regulator-always-on;
+ regulator-boot-on;
gpio = <&expander0 2 GPIO_ACTIVE_HIGH>;
};
regulator-name = "v5.0-sata0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- regulator-always-on;
vin-supply = <®_sata0>;
};
regulator-name = "v12.0-sata0";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
- regulator-always-on;
vin-supply = <®_sata0>;
};
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
enable-active-high;
- regulator-always-on;
+ regulator-boot-on;
gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
};
regulator-name = "v5.0-sata1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- regulator-always-on;
vin-supply = <®_sata1>;
};
regulator-name = "v12.0-sata1";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
- regulator-always-on;
vin-supply = <®_sata1>;
};
compatible = "regulator-fixed";
regulator-name = "pwr_en_sata2";
enable-active-high;
- regulator-always-on;
+ regulator-boot-on;
gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
};
regulator-name = "v5.0-sata2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- regulator-always-on;
vin-supply = <®_sata2>;
};
regulator-name = "v12.0-sata2";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
- regulator-always-on;
vin-supply = <®_sata2>;
};
compatible = "regulator-fixed";
regulator-name = "pwr_en_sata3";
enable-active-high;
- regulator-always-on;
+ regulator-boot-on;
gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
};
regulator-name = "v5.0-sata3";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- regulator-always-on;
vin-supply = <®_sata3>;
};
regulator-name = "v12.0-sata3";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
- regulator-always-on;
vin-supply = <®_sata3>;
};
};
reg = <0x22000 0x1000>;
};
+ /*
+ * As a special exception to the "order by
+ * register address" rule, the eth0 node is
+ * placed here to ensure that it gets
+ * registered as the first interface, since
+ * the network subsystem doesn't allow naming
+ * interfaces using DT aliases. Without this,
+ * the ordering of interfaces is different
+ * from the one used in U-Boot and the
+ * labeling of interfaces on the boards, which
+ * is very confusing for users.
+ */
+ eth0: ethernet@70000 {
+ compatible = "marvell,armada-370-neta";
+ reg = <0x70000 0x4000>;
+ interrupts-extended = <&mpic 8>;
+ clocks = <&gateclk 4>;
+ tx-csum-limit = <9800>;
+ status = "disabled";
+ };
+
eth1: ethernet@30000 {
compatible = "marvell,armada-370-neta";
reg = <0x30000 0x4000>;
};
};
- eth0: ethernet@70000 {
- compatible = "marvell,armada-370-neta";
- reg = <0x70000 0x4000>;
- interrupts-extended = <&mpic 8>;
- clocks = <&gateclk 4>;
- tx-csum-limit = <9800>;
- status = "disabled";
- };
-
mdio: mdio@72004 {
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
+ bm: bm@c8000 {
+ compatible = "marvell,armada-380-neta-bm";
+ reg = <0xc8000 0xac>;
+ clocks = <&gateclk 13>;
+ internal-mem = <&bm_bppi>;
+ status = "disabled";
+ };
+
sata@e0000 {
compatible = "marvell,armada-380-ahci";
reg = <0xe0000 0x2000>;
#size-cells = <1>;
ranges = <0 MBUS_ID(0x09, 0x15) 0 0x800>;
};
+
+ bm_bppi: bm-bppi {
+ compatible = "mmio-sram";
+ reg = <MBUS_ID(0x0c, 0x04) 0 0x100000>;
+ ranges = <0 MBUS_ID(0x0c, 0x04) 0 0x100000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gateclk 13>;
+ no-memory-wc;
+ status = "disabled";
+ };
};
clocks {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
- MBUS_ID(0x09, 0x09) 0 0 0xf8100000 0x10000
- MBUS_ID(0x09, 0x05) 0 0 0xf8110000 0x10000>;
+ MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>;
devbus-bootcs {
status = "okay";
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
+ buffer-manager = <&bm>;
+ bm,pool-long = <0>;
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
phy-mode = "rgmii-id";
+ buffer-manager = <&bm>;
+ bm,pool-long = <1>;
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <2>;
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <3>;
+ };
+
+ bm@c0000 {
+ status = "okay";
};
mvsdio@d4000 {
spi-max-frequency = <20000000>;
};
};
+
+ nand@d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x800000>;
+ };
+ partition@800000 {
+ label = "Linux";
+ reg = <0x800000 0x800000>;
+ };
+ partition@1000000 {
+ label = "Filesystem";
+ reg = <0x1000000 0x3f000000>;
+
+ };
+ };
+ };
};
+
+ bm-bppi {
+ status = "okay";
+ };
};
};
#define MAX_SOURCES 400
/ {
- #address-cells = <1>;
- #size-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
compatible = "ti,dra7xx";
interrupt-parent = <&crossbar_mpu>;
compatible = "arm,cortex-a15-gic";
interrupt-controller;
#interrupt-cells = <3>;
- reg = <0x48211000 0x1000>,
- <0x48212000 0x1000>,
- <0x48214000 0x2000>,
- <0x48216000 0x2000>;
+ reg = <0x0 0x48211000 0x0 0x1000>,
+ <0x0 0x48212000 0x0 0x1000>,
+ <0x0 0x48214000 0x0 0x2000>,
+ <0x0 0x48216000 0x0 0x2000>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
interrupt-parent = <&gic>;
};
compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
interrupt-controller;
#interrupt-cells = <3>;
- reg = <0x48281000 0x1000>;
+ reg = <0x0 0x48281000 0x0 0x1000>;
interrupt-parent = <&gic>;
};
compatible = "ti,dra7-l3-noc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges;
+ ranges = <0x0 0x0 0x0 0xc0000000>;
ti,hwmods = "l3_main_1", "l3_main_2";
- reg = <0x44000000 0x1000000>,
- <0x45000000 0x1000>;
+ reg = <0x0 0x44000000 0x0 0x1000000>,
+ <0x0 0x45000000 0x0 0x1000>;
interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
<&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
compatible = "syscon";
reg = <0x1c04 0x0020>;
};
+
+ scm_conf_pcie: scm_conf@1c24 {
+ compatible = "syscon";
+ reg = <0x1c24 0x0024>;
+ };
};
cm_core_aon: cm_core_aon@5000 {
status = "disabled";
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
reg = <0x4a094000 0x80>, /* phy_rx */
<0x4a094400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie1phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x1c>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy1_32khz>,
<&optfclk_pciephy1_clk>,
<&optfclk_pciephy1_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
};
reg = <0x4a095000 0x80>, /* phy_rx */
<0x4a095400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie2phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x20>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy2_32khz>,
<&optfclk_pciephy2_clk>,
<&optfclk_pciephy2_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
status = "disabled";
};
ti,hwmods = "sata";
};
- omap_control_pcie1phy: control-phy@0x4a003c40 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c40 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
- omap_control_pcie2phy: control-pcie@0x4a003c44 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c44 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- status = "disabled";
- };
-
rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
clocks = <&sys_32k_ck>;
};
- omap_control_usb2phy1: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy1: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb2phy2: control-phy@0x4a002e74 {
- compatible = "ti,control-phy-usb2-dra7";
- reg = <0x4a002e74 0x4>;
- reg-names = "power";
- };
-
/* OCP2SCP1 */
ocp2scp@4a080000 {
compatible = "ti,omap-ocp2scp";
usb2_phy1: phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x400>;
- ctrl-module = <&omap_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk",
};
usb2_phy2: phy@4a085000 {
- compatible = "ti,omap-usb2";
+ compatible = "ti,dra7x-usb2-phy2",
+ "ti,omap-usb2";
reg = <0x4a085000 0x400>;
- ctrl-module = <&omap_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0xe74>;
clocks = <&usb_phy2_always_on_clk32k>,
<&usb_otg_ss2_refclk960m>;
clock-names = "wkupclk",
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy1>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy3_always_on_clk32k>,
<&sys_clkin1>,
<&usb_otg_ss1_refclk960m>;
"otg";
phys = <&usb2_phy1>, <&usb3_phy1>;
phy-names = "usb2-phy", "usb3-phy";
- tx-fifo-resize;
maximum-speed = "super-speed";
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
"otg";
phys = <&usb2_phy2>;
phy-names = "usb2-phy";
- tx-fifo-resize;
maximum-speed = "high-speed";
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
interrupt-names = "peripheral",
"host",
"otg";
- tx-fifo-resize;
maximum-speed = "high-speed";
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
gpmc,num-waitpins = <2>;
#address-cells = <2>;
#size-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
status = "disabled";
};
0x48485200 0x2E00>;
#address-cells = <1>;
#size-cells = <1>;
+
+ /*
+ * Do not allow gating of cpsw clock as workaround
+ * for errata i877. Keeping internal clock disabled
+ * causes the device switching characteristics
+ * to degrade over time and eventually fail to meet
+ * the data manual delay time/skew specs.
+ */
+ ti,no-idle;
+
/*
* rx_thresh_pend
* rx_pend
#include "omap4-cpu-thermal.dtsi"
#include "omap5-gpu-thermal.dtsi"
#include "omap5-core-thermal.dtsi"
+ #include "dra7-dspeve-thermal.dtsi"
+ #include "dra7-iva-thermal.dtsi"
};
};
camera_lens_cover {
label = "Camera Lens Cover";
gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
- wakeup-source;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_CAMERA_LENS_COVER>;
+ linux,can-disable;
};
camera_focus {
label = "Camera Focus";
gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
- linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
- wakeup-source;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ linux,can-disable;
};
camera_capture {
label = "Camera Capture";
gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
- linux,code = <0xd4>; /* KEY_CAMERA */
- wakeup-source;
+ linux,code = <KEY_CAMERA>;
+ linux,can-disable;
};
lock_button {
label = "Lock Button";
gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
- linux,code = <0x98>; /* KEY_SCREENLOCK */
- wakeup-source;
+ linux,code = <KEY_SCREENLOCK>;
+ linux,can-disable;
};
keypad_slide {
label = "Keypad Slide";
gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
- wakeup-source;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_KEYPAD_SLIDE>;
+ linux,can-disable;
};
proximity_sensor {
label = "Proximity Sensor";
gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_FRONT_PROXIMITY>;
+ linux,can-disable;
};
};
- isp1704: isp1704 {
- compatible = "nxp,isp1704";
+ isp1707: isp1707 {
+ compatible = "nxp,isp1707";
nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
usb-phy = <&usb2_phy>;
};
amstaos,cover-comp-gain = <16>;
};
+ adp1653: led-controller@30 {
+ compatible = "adi,adp1653";
+ reg = <0x30>;
+ enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
+
+ flash {
+ flash-timeout-us = <500000>;
+ flash-max-microamp = <320000>;
+ led-max-microamp = <50000>;
+ };
+ indicator {
+ led-max-microamp = <17500>;
+ };
+ };
+
lp5523: lp5523@32 {
compatible = "national,lp5523";
reg = <0x32>;
ti,termination-current = <100>;
ti,resistor-sense = <68>;
- ti,usb-charger-detection = <&isp1704>;
+ ti,usb-charger-detection = <&isp1707>;
};
};
interrupts = <25>;
#dma-channels = <32>;
#dma-cells = <2>;
+ #dma-requests = <100>;
status = "okay";
};
reg = <0x43100000 90>;
interrupts = <45>;
clocks = <&clks CLK_NAND>;
- dmas = <&pdma 97>;
+ dmas = <&pdma 97 3>;
dma-names = "data";
#address-cells = <1>;
#size-cells = <1>;
model = "Rockchip RK3036 KylinBoard";
compatible = "rockchip,rk3036-kylin", "rockchip,rk3036";
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ work {
+ gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+ label = "kylin:red:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_ctl>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_wake_h>;
+
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - SDIO_RESET_L_WL_RST
+ * - SDIO_RESET_L_BT_EN
+ */
+ reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
+ <&gpio0 27 GPIO_ACTIVE_LOW>, /* WL_RST */
+ <&gpio2 9 GPIO_ACTIVE_LOW>; /* BT_EN */
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "rockchip,rt5616-codec";
+ simple-audio-card,mclk-fs = <512>;
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "MIC1", "Microphone Jack",
+ "MIC2", "Microphone Jack",
+ "Microphone Jack", "micbias1",
+ "Headphone Jack", "HPOL",
+ "Headphone Jack", "HPOR";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rt5616>;
+ };
+ };
+
vcc_sys: vsys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
+ phy = <&phy0>;
+ phy-reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* PHY_RST */
+ phy-reset-duration = <10>; /* millisecond */
+
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
&emmc {
status = "okay";
};
&i2c2 {
status = "okay";
+
+ rt5616: rt5616@1b {
+ compatible = "rt5616";
+ reg = <0x1b>;
+ clocks = <&cru SCLK_I2S_OUT>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
+ };
+ };
+
+ &i2s {
+ #sound-dai-cells = <0>;
+ status = "okay";
};
&sdio {
broken-cd;
bus-width = <4>;
+ cap-sd-highspeed;
cap-sdio-irq;
default-sample-phase = <90>;
keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
non-removable;
num-slots = <1>;
pinctrl-names = "default";
pinctrl-0 = <&sdio_clk &sdio_cmd &sdio_bus4>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ };
+
+ &sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+ };
+
+ &uart0 {
+ status = "okay";
};
&uart2 {
};
&pinctrl {
+ leds {
+ led_ctl: led-ctl {
+ rockchip,pins = <2 30 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
pmic {
pmic_int: pmic-int {
rockchip,pins = <2 2 RK_FUNC_GPIO &pcfg_pull_default>;
};
};
+ sdio {
+ bt_wake_h: bt-wake-h {
+ rockchip,pins = <2 8 RK_FUNC_GPIO &pcfg_pull_default>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <2 28 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
sleep {
global_pwroff: global-pwroff {
rockchip,pins = <2 7 RK_FUNC_1 &pcfg_pull_none>;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
+ spi = &spi;
};
memory {
};
amba {
- compatible = "arm,amba-bus";
+ compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
+ arm,pl330-broken-no-flushp;
clocks = <&cru ACLK_DMAC2>;
clock-names = "apb_pclk";
};
};
usb_otg: usb@10180000 {
- compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
+ compatible = "rockchip,rk3036-usb", "rockchip,rk3066-usb",
"snps,dwc2";
reg = <0x10180000 0x40000>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
};
usb_host: usb@101c0000 {
- compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
+ compatible = "rockchip,rk3036-usb", "rockchip,rk3066-usb",
"snps,dwc2";
reg = <0x101c0000 0x40000>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
+ emac: ethernet@10200000 {
+ compatible = "rockchip,rk3036-emac", "snps,arc-emac";
+ reg = <0x10200000 0x4000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ rockchip,grf = <&grf>;
+ clocks = <&cru HCLK_MAC>, <&cru SCLK_MACREF>, <&cru SCLK_MAC>;
+ clock-names = "hclk", "macref", "macclk";
+ /*
+ * Fix the emac parent clock is DPLL instead of APLL.
+ * since that will cause some unstable things if the cpufreq
+ * is working. (e.g: the accurate 50MHz what mac_ref need)
+ */
+ assigned-clocks = <&cru SCLK_MACPLL>;
+ assigned-clock-parents = <&cru PLL_DPLL>;
+ max-speed = <100>;
+ phy-mode = "rmii";
+ status = "disabled";
+ };
+
sdmmc: dwmmc@10214000 {
compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x10214000 0x4000>;
};
emmc: dwmmc@1021c000 {
- compatible = "rockchip,rk3288-dw-mshc";
+ compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x1021c000 0x4000>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
broken-cd;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
- clock-names = "i2s_hclk", "i2s_clk";
- clocks = <&cru HCLK_I2S>, <&cru SCLK_I2S>;
+ clock-names = "i2s_clk", "i2s_hclk";
+ clocks = <&cru SCLK_I2S>, <&cru HCLK_I2S>;
dmas = <&pdma 0>, <&pdma 1>;
dma-names = "tx", "rx";
pinctrl-names = "default";
};
i2c1: i2c@20056000 {
- compatible = "rockchip,rk3288-i2c";
+ compatible = "rockchip,rk3036-i2c", "rockchip,rk3288-i2c";
reg = <0x20056000 0x1000>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
};
i2c2: i2c@2005a000 {
- compatible = "rockchip,rk3288-i2c";
+ compatible = "rockchip,rk3036-i2c", "rockchip,rk3288-i2c";
reg = <0x2005a000 0x1000>;
interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
};
i2c0: i2c@20072000 {
- compatible = "rockchip,rk3288-i2c";
+ compatible = "rockchip,rk3036-i2c", "rockchip,rk3288-i2c";
reg = <0x20072000 0x1000>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
status = "disabled";
};
+ spi: spi@20074000 {
+ compatible = "rockchip,rockchip-spi";
+ reg = <0x20074000 0x1000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks =<&cru PCLK_SPI>, <&cru SCLK_SPI>;
+ clock-names = "apb-pclk","spi_pclk";
+ dmas = <&pdma 8>, <&pdma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_txd &spi_rxd &spi_clk &spi_cs0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
pinctrl: pinctrl {
compatible = "rockchip,rk3036-pinctrl";
rockchip,grf = <&grf>;
};
};
+ emac {
+ emac_xfer: emac-xfer {
+ rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_default>, /* crs_dvalid */
+ <2 13 RK_FUNC_1 &pcfg_pull_default>, /* tx_en */
+ <2 14 RK_FUNC_1 &pcfg_pull_default>, /* mac_clk */
+ <2 15 RK_FUNC_1 &pcfg_pull_default>, /* rx_err */
+ <2 16 RK_FUNC_1 &pcfg_pull_default>, /* rxd1 */
+ <2 17 RK_FUNC_1 &pcfg_pull_default>, /* rxd0 */
+ <2 18 RK_FUNC_1 &pcfg_pull_default>, /* txd1 */
+ <2 19 RK_FUNC_1 &pcfg_pull_default>; /* txd0 */
+ };
+
+ emac_mdio: emac-mdio {
+ rockchip,pins = <2 12 RK_FUNC_1 &pcfg_pull_default>, /* mac_md */
+ <2 25 RK_FUNC_1 &pcfg_pull_default>; /* mac_mdclk */
+ };
+ };
+
i2c0 {
i2c0_xfer: i2c0-xfer {
rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>,
i2s {
i2s_bus: i2s-bus {
- rockchip,pins = <1 0 RK_FUNC_1 &pcfg_pull_none>,
- <1 1 RK_FUNC_1 &pcfg_pull_none>,
- <1 2 RK_FUNC_1 &pcfg_pull_none>,
- <1 3 RK_FUNC_1 &pcfg_pull_none>,
- <1 4 RK_FUNC_1 &pcfg_pull_none>,
- <1 5 RK_FUNC_1 &pcfg_pull_none>;
+ rockchip,pins = <1 0 RK_FUNC_1 &pcfg_pull_default>,
+ <1 1 RK_FUNC_1 &pcfg_pull_default>,
+ <1 2 RK_FUNC_1 &pcfg_pull_default>,
+ <1 3 RK_FUNC_1 &pcfg_pull_default>,
+ <1 4 RK_FUNC_1 &pcfg_pull_default>,
+ <1 5 RK_FUNC_1 &pcfg_pull_default>;
};
};
};
/* no rts / cts for uart2 */
};
+
+ spi {
+ spi_txd:spi-txd {
+ rockchip,pins = <1 29 RK_FUNC_3 &pcfg_pull_default>;
+ };
+
+ spi_rxd:spi-rxd {
+ rockchip,pins = <1 28 RK_FUNC_3 &pcfg_pull_default>;
+ };
+
+ spi_clk:spi-clk {
+ rockchip,pins = <2 0 RK_FUNC_2 &pcfg_pull_default>;
+ };
+
+ spi_cs0:spi-cs0 {
+ rockchip,pins = <1 30 RK_FUNC_3 &pcfg_pull_default>;
+
+ };
+
+ spi_cs1:spi-cs1 {
+ rockchip,pins = <1 31 RK_FUNC_3 &pcfg_pull_default>;
+
+ };
+ };
};
};
ranges;
amba {
- compatible = "arm,amba-bus";
+ compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
status = "disabled";
};
+ eccmgr: eccmgr@ffd08140 {
+ compatible = "altr,socfpga-ecc-manager";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ l2-ecc@ffd08140 {
+ compatible = "altr,socfpga-l2-ecc";
+ reg = <0xffd08140 0x4>;
+ interrupts = <0 36 1>, <0 37 1>;
+ };
+
+ ocram-ecc@ffd08144 {
+ compatible = "altr,socfpga-ocram-ecc";
+ reg = <0xffd08144 0x4>;
+ iram = <&ocram>;
+ interrupts = <0 178 1>, <0 179 1>;
+ };
+ };
+
L2: l2-cache@fffef000 {
compatible = "arm,pl310-cache";
reg = <0xfffef000 0x1000>;
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
-static phys_addr_t keystone_virt_to_idmap(unsigned long x)
+static unsigned long keystone_virt_to_idmap(unsigned long x)
{
return (phys_addr_t)(x) - CONFIG_PAGE_OFFSET + KEYSTONE_LOW_PHYS_START;
}
"ti,k2hk",
"ti,k2e",
"ti,k2l",
+ "ti,k2g",
"ti,keystone",
NULL,
};