ARM: dts: lpc32xx: phy3250: avoid extension of device nodes by absolute path

The change simplifies layout of PHY3250 board description by
referencing device nodes of LPC32xx controllers by label.

No functional change intended.

Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts
index 26e070fe9a589b89e8aba58b3d76a900170b4cde..c1a6e624bf19505b907cba187626a1060705a747 100644 (file)
--- a/arch/arm/boot/dts/phy3250.dts
+++ b/arch/arm/boot/dts/phy3250.dts
@@ -56,147 +56,6 @@
                };
        };
 
-       ahb {
-               mac: ethernet@31060000 {
-                       phy-mode = "rmii";
-                       use-iram;
-               };
-
-               clcd@31040000 {
-                       status = "okay";
-               };
-
-               /* 64MB Flash via SLC NAND controller */
-               slc: flash@20020000 {
-                       status = "okay";
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-
-                       nxp,wdr-clks = <14>;
-                       nxp,wwidth = <40000000>;
-                       nxp,whold = <100000000>;
-                       nxp,wsetup = <100000000>;
-                       nxp,rdr-clks = <14>;
-                       nxp,rwidth = <40000000>;
-                       nxp,rhold = <66666666>;
-                       nxp,rsetup = <100000000>;
-                       nand-on-flash-bbt;
-                       gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
-
-                       mtd0@00000000 {
-                               label = "phy3250-boot";
-                               reg = <0x00000000 0x00064000>;
-                               read-only;
-                       };
-
-                       mtd1@00064000 {
-                               label = "phy3250-uboot";
-                               reg = <0x00064000 0x00190000>;
-                               read-only;
-                       };
-
-                       mtd2@001f4000 {
-                               label = "phy3250-ubt-prms";
-                               reg = <0x001f4000 0x00010000>;
-                       };
-
-                       mtd3@00204000 {
-                               label = "phy3250-kernel";
-                               reg = <0x00204000 0x00400000>;
-                       };
-
-                       mtd4@00604000 {
-                               label = "phy3250-rootfs";
-                               reg = <0x00604000 0x039fc000>;
-                       };
-               };
-
-               apb {
-                       uart5: serial@40090000 {
-                               status = "okay";
-                       };
-
-                       uart3: serial@40080000 {
-                               status = "okay";
-                       };
-
-                       i2c1: i2c@400A0000 {
-                               clock-frequency = <100000>;
-
-                               pcf8563: rtc@51 {
-                                       compatible = "nxp,pcf8563";
-                                       reg = <0x51>;
-                               };
-
-                               uda1380: uda1380@18 {
-                                       compatible = "nxp,uda1380";
-                                       reg = <0x18>;
-                                       power-gpio = <&gpio 0x59 0>;
-                                       reset-gpio = <&gpio 0x51 0>;
-                                       dac-clk = "wspll";
-                               };
-                       };
-
-                       i2c2: i2c@400A8000 {
-                               clock-frequency = <100000>;
-                       };
-
-                       ssp0: ssp@20084000 {
-                               #address-cells = <1>;
-                               #size-cells = <0>;
-                               num-cs = <1>;
-                               cs-gpios = <&gpio 3 5 0>;
-                               status = "okay";
-
-                               eeprom: at25@0 {
-                                       pl022,interface = <0>;
-                                       pl022,com-mode = <0>;
-                                       pl022,rx-level-trig = <1>;
-                                       pl022,tx-level-trig = <1>;
-                                       pl022,ctrl-len = <11>;
-                                       pl022,wait-state = <0>;
-                                       pl022,duplex = <0>;
-
-                                       at25,byte-len = <0x8000>;
-                                       at25,addr-mode = <2>;
-                                       at25,page-size = <64>;
-
-                                       compatible = "atmel,at25";
-                                       reg = <0>;
-                                       spi-max-frequency = <5000000>;
-                               };
-                       };
-
-                       sd@20098000 {
-                               wp-gpios = <&gpio 3 0 0>;
-                               cd-gpios = <&gpio 3 1 0>;
-                               cd-inverted;
-                               bus-width = <4>;
-                               vmmc-supply = <&sd_reg>;
-                               status = "okay";
-                       };
-               };
-
-               fab {
-                       uart2: serial@40018000 {
-                               status = "okay";
-                       };
-
-                       tsc@40048000 {
-                               status = "okay";
-                       };
-
-                       key@40050000 {
-                               status = "okay";
-                               keypad,num-rows = <1>;
-                               keypad,num-columns = <1>;
-                               nxp,debounce-delay-ms = <3>;
-                               nxp,scan-delay-ms = <34>;
-                               linux,keymap = <0x00000002>;
-                       };
-               };
-       };
-
        leds {
                compatible = "gpio-leds";
 
@@ -212,12 +71,31 @@
        };
 };
 
-/* Here, choose exactly one from: ohci, usbd */
-&ohci /* &usbd */ {
-       transceiver = <&isp1301>;
+&clcd {
        status = "okay";
 };
 
+&i2c1 {
+       clock-frequency = <100000>;
+
+       uda1380: uda1380@18 {
+               compatible = "nxp,uda1380";
+               reg = <0x18>;
+               power-gpio = <&gpio 0x59 0>;
+               reset-gpio = <&gpio 0x51 0>;
+               dac-clk = "wspll";
+       };
+
+       pcf8563: rtc@51 {
+               compatible = "nxp,pcf8563";
+               reg = <0x51>;
+       };
+};
+
+&i2c2 {
+       clock-frequency = <100000>;
+};
+
 &i2cusb {
        clock-frequency = <100000>;
 
@@ -226,3 +104,119 @@
                reg = <0x2c>;
        };
 };
+
+&key {
+       keypad,num-rows = <1>;
+       keypad,num-columns = <1>;
+       nxp,debounce-delay-ms = <3>;
+       nxp,scan-delay-ms = <34>;
+       linux,keymap = <0x00000002>;
+       status = "okay";
+};
+
+&mac {
+       phy-mode = "rmii";
+       use-iram;
+};
+
+/* Here, choose exactly one from: ohci, usbd */
+&ohci /* &usbd */ {
+       transceiver = <&isp1301>;
+       status = "okay";
+};
+
+&sd {
+       wp-gpios = <&gpio 3 0 0>;
+       cd-gpios = <&gpio 3 1 0>;
+       cd-inverted;
+       bus-width = <4>;
+       vmmc-supply = <&sd_reg>;
+       status = "okay";
+};
+
+/* 64MB Flash via SLC NAND controller */
+&slc {
+       #address-cells = <1>;
+       #size-cells = <1>;
+       status = "okay";
+
+       nxp,wdr-clks = <14>;
+       nxp,wwidth = <40000000>;
+       nxp,whold = <100000000>;
+       nxp,wsetup = <100000000>;
+       nxp,rdr-clks = <14>;
+       nxp,rwidth = <40000000>;
+       nxp,rhold = <66666666>;
+       nxp,rsetup = <100000000>;
+       nand-on-flash-bbt;
+       gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+       mtd0@00000000 {
+               label = "phy3250-boot";
+               reg = <0x00000000 0x00064000>;
+               read-only;
+       };
+
+       mtd1@00064000 {
+               label = "phy3250-uboot";
+               reg = <0x00064000 0x00190000>;
+               read-only;
+       };
+
+       mtd2@001f4000 {
+               label = "phy3250-ubt-prms";
+               reg = <0x001f4000 0x00010000>;
+       };
+
+       mtd3@00204000 {
+               label = "phy3250-kernel";
+               reg = <0x00204000 0x00400000>;
+       };
+
+       mtd4@00604000 {
+               label = "phy3250-rootfs";
+               reg = <0x00604000 0x039fc000>;
+       };
+};
+
+&ssp0 {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       num-cs = <1>;
+       cs-gpios = <&gpio 3 5 0>;
+       status = "okay";
+
+       eeprom: at25@0 {
+               compatible = "atmel,at25";
+               reg = <0>;
+               spi-max-frequency = <5000000>;
+
+               pl022,interface = <0>;
+               pl022,com-mode = <0>;
+               pl022,rx-level-trig = <1>;
+               pl022,tx-level-trig = <1>;
+               pl022,ctrl-len = <11>;
+               pl022,wait-state = <0>;
+               pl022,duplex = <0>;
+
+               at25,byte-len = <0x8000>;
+               at25,addr-mode = <2>;
+               at25,page-size = <64>;
+       };
+};
+
+&tsc {
+       status = "okay";
+};
+
+&uart2 {
+       status = "okay";
+};
+
+&uart3 {
+       status = "okay";
+};
+
+&uart5 {
+       status = "okay";
+};