--- /dev/null
- struct rpmsg_endpoint *rpmsg_create_ept(struct rpmsg_channel *rpdev,
- void (*cb)(struct rpmsg_channel *, void *, int, void *, u32),
- void *priv, u32 addr);
+============================================
+Remote Processor Messaging (rpmsg) Framework
+============================================
+
+.. note::
+
+ This document describes the rpmsg bus and how to write rpmsg drivers.
+ To learn how to add rpmsg support for new platforms, check out remoteproc.txt
+ (also a resident of Documentation/).
+
+Introduction
+============
+
+Modern SoCs typically employ heterogeneous remote processor devices in
+asymmetric multiprocessing (AMP) configurations, which may be running
+different instances of operating system, whether it's Linux or any other
+flavor of real-time OS.
+
+OMAP4, for example, has dual Cortex-A9, dual Cortex-M3 and a C64x+ DSP.
+Typically, the dual cortex-A9 is running Linux in a SMP configuration,
+and each of the other three cores (two M3 cores and a DSP) is running
+its own instance of RTOS in an AMP configuration.
+
+Typically AMP remote processors employ dedicated DSP codecs and multimedia
+hardware accelerators, and therefore are often used to offload CPU-intensive
+multimedia tasks from the main application processor.
+
+These remote processors could also be used to control latency-sensitive
+sensors, drive random hardware blocks, or just perform background tasks
+while the main CPU is idling.
+
+Users of those remote processors can either be userland apps (e.g. multimedia
+frameworks talking with remote OMX components) or kernel drivers (controlling
+hardware accessible only by the remote processor, reserving kernel-controlled
+resources on behalf of the remote processor, etc..).
+
+Rpmsg is a virtio-based messaging bus that allows kernel drivers to communicate
+with remote processors available on the system. In turn, drivers could then
+expose appropriate user space interfaces, if needed.
+
+When writing a driver that exposes rpmsg communication to userland, please
+keep in mind that remote processors might have direct access to the
+system's physical memory and other sensitive hardware resources (e.g. on
+OMAP4, remote cores and hardware accelerators may have direct access to the
+physical memory, gpio banks, dma controllers, i2c bus, gptimers, mailbox
+devices, hwspinlocks, etc..). Moreover, those remote processors might be
+running RTOS where every task can access the entire memory/devices exposed
+to the processor. To minimize the risks of rogue (or buggy) userland code
+exploiting remote bugs, and by that taking over the system, it is often
+desired to limit userland to specific rpmsg channels (see definition below)
+it can send messages on, and if possible, minimize how much control
+it has over the content of the messages.
+
+Every rpmsg device is a communication channel with a remote processor (thus
+rpmsg devices are called channels). Channels are identified by a textual name
+and have a local ("source") rpmsg address, and remote ("destination") rpmsg
+address.
+
+When a driver starts listening on a channel, its rx callback is bound with
+a unique rpmsg local address (a 32-bit integer). This way when inbound messages
+arrive, the rpmsg core dispatches them to the appropriate driver according
+to their destination address (this is done by invoking the driver's rx handler
+with the payload of the inbound message).
+
+
+User API
+========
+
+::
+
+ int rpmsg_send(struct rpmsg_channel *rpdev, void *data, int len);
+
+sends a message across to the remote processor on a given channel.
+The caller should specify the channel, the data it wants to send,
+and its length (in bytes). The message will be sent on the specified
+channel, i.e. its source and destination address fields will be
+set to the channel's src and dst addresses.
+
+In case there are no TX buffers available, the function will block until
+one becomes available (i.e. until the remote processor consumes
+a tx buffer and puts it back on virtio's used descriptor ring),
+or a timeout of 15 seconds elapses. When the latter happens,
+-ERESTARTSYS is returned.
+
+The function can only be called from a process context (for now).
+Returns 0 on success and an appropriate error value on failure.
+
+::
+
+ int rpmsg_sendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst);
+
+sends a message across to the remote processor on a given channel,
+to a destination address provided by the caller.
+
+The caller should specify the channel, the data it wants to send,
+its length (in bytes), and an explicit destination address.
+
+The message will then be sent to the remote processor to which the
+channel belongs, using the channel's src address, and the user-provided
+dst address (thus the channel's dst address will be ignored).
+
+In case there are no TX buffers available, the function will block until
+one becomes available (i.e. until the remote processor consumes
+a tx buffer and puts it back on virtio's used descriptor ring),
+or a timeout of 15 seconds elapses. When the latter happens,
+-ERESTARTSYS is returned.
+
+The function can only be called from a process context (for now).
+Returns 0 on success and an appropriate error value on failure.
+
+::
+
+ int rpmsg_send_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst,
+ void *data, int len);
+
+
+sends a message across to the remote processor, using the src and dst
+addresses provided by the user.
+
+The caller should specify the channel, the data it wants to send,
+its length (in bytes), and explicit source and destination addresses.
+The message will then be sent to the remote processor to which the
+channel belongs, but the channel's src and dst addresses will be
+ignored (and the user-provided addresses will be used instead).
+
+In case there are no TX buffers available, the function will block until
+one becomes available (i.e. until the remote processor consumes
+a tx buffer and puts it back on virtio's used descriptor ring),
+or a timeout of 15 seconds elapses. When the latter happens,
+-ERESTARTSYS is returned.
+
+The function can only be called from a process context (for now).
+Returns 0 on success and an appropriate error value on failure.
+
+::
+
+ int rpmsg_trysend(struct rpmsg_channel *rpdev, void *data, int len);
+
+sends a message across to the remote processor on a given channel.
+The caller should specify the channel, the data it wants to send,
+and its length (in bytes). The message will be sent on the specified
+channel, i.e. its source and destination address fields will be
+set to the channel's src and dst addresses.
+
+In case there are no TX buffers available, the function will immediately
+return -ENOMEM without waiting until one becomes available.
+
+The function can only be called from a process context (for now).
+Returns 0 on success and an appropriate error value on failure.
+
+::
+
+ int rpmsg_trysendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst)
+
+
+sends a message across to the remote processor on a given channel,
+to a destination address provided by the user.
+
+The user should specify the channel, the data it wants to send,
+its length (in bytes), and an explicit destination address.
+
+The message will then be sent to the remote processor to which the
+channel belongs, using the channel's src address, and the user-provided
+dst address (thus the channel's dst address will be ignored).
+
+In case there are no TX buffers available, the function will immediately
+return -ENOMEM without waiting until one becomes available.
+
+The function can only be called from a process context (for now).
+Returns 0 on success and an appropriate error value on failure.
+
+::
+
+ int rpmsg_trysend_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst,
+ void *data, int len);
+
+
+sends a message across to the remote processor, using source and
+destination addresses provided by the user.
+
+The user should specify the channel, the data it wants to send,
+its length (in bytes), and explicit source and destination addresses.
+The message will then be sent to the remote processor to which the
+channel belongs, but the channel's src and dst addresses will be
+ignored (and the user-provided addresses will be used instead).
+
+In case there are no TX buffers available, the function will immediately
+return -ENOMEM without waiting until one becomes available.
+
+The function can only be called from a process context (for now).
+Returns 0 on success and an appropriate error value on failure.
+
+::
+
++ struct rpmsg_endpoint *rpmsg_create_ept(struct rpmsg_device *rpdev,
++ rpmsg_rx_cb_t cb, void *priv,
++ struct rpmsg_channel_info chinfo);
+
+every rpmsg address in the system is bound to an rx callback (so when
+inbound messages arrive, they are dispatched by the rpmsg bus using the
+appropriate callback handler) by means of an rpmsg_endpoint struct.
+
+This function allows drivers to create such an endpoint, and by that,
+bind a callback, and possibly some private data too, to an rpmsg address
+(either one that is known in advance, or one that will be dynamically
+assigned for them).
+
+Simple rpmsg drivers need not call rpmsg_create_ept, because an endpoint
+is already created for them when they are probed by the rpmsg bus
+(using the rx callback they provide when they registered to the rpmsg bus).
+
+So things should just work for simple drivers: they already have an
+endpoint, their rx callback is bound to their rpmsg address, and when
+relevant inbound messages arrive (i.e. messages which their dst address
+equals to the src address of their rpmsg channel), the driver's handler
+is invoked to process it.
+
+That said, more complicated drivers might do need to allocate
+additional rpmsg addresses, and bind them to different rx callbacks.
+To accomplish that, those drivers need to call this function.
+Drivers should provide their channel (so the new endpoint would bind
+to the same remote processor their channel belongs to), an rx callback
+function, an optional private data (which is provided back when the
+rx callback is invoked), and an address they want to bind with the
+callback. If addr is RPMSG_ADDR_ANY, then rpmsg_create_ept will
+dynamically assign them an available rpmsg address (drivers should have
+a very good reason why not to always use RPMSG_ADDR_ANY here).
+
+Returns a pointer to the endpoint on success, or NULL on error.
+
+::
+
+ void rpmsg_destroy_ept(struct rpmsg_endpoint *ept);
+
+
+destroys an existing rpmsg endpoint. user should provide a pointer
+to an rpmsg endpoint that was previously created with rpmsg_create_ept().
+
+::
+
+ int register_rpmsg_driver(struct rpmsg_driver *rpdrv);
+
+
+registers an rpmsg driver with the rpmsg bus. user should provide
+a pointer to an rpmsg_driver struct, which contains the driver's
+->probe() and ->remove() functions, an rx callback, and an id_table
+specifying the names of the channels this driver is interested to
+be probed with.
+
+::
+
+ void unregister_rpmsg_driver(struct rpmsg_driver *rpdrv);
+
+
+unregisters an rpmsg driver from the rpmsg bus. user should provide
+a pointer to a previously-registered rpmsg_driver struct.
+Returns 0 on success, and an appropriate error value on failure.
+
+
+Typical usage
+=============
+
+The following is a simple rpmsg driver, that sends an "hello!" message
+on probe(), and whenever it receives an incoming message, it dumps its
+content to the console.
+
+::
+
+ #include <linux/kernel.h>
+ #include <linux/module.h>
+ #include <linux/rpmsg.h>
+
+ static void rpmsg_sample_cb(struct rpmsg_channel *rpdev, void *data, int len,
+ void *priv, u32 src)
+ {
+ print_hex_dump(KERN_INFO, "incoming message:", DUMP_PREFIX_NONE,
+ 16, 1, data, len, true);
+ }
+
+ static int rpmsg_sample_probe(struct rpmsg_channel *rpdev)
+ {
+ int err;
+
+ dev_info(&rpdev->dev, "chnl: 0x%x -> 0x%x\n", rpdev->src, rpdev->dst);
+
+ /* send a message on our channel */
+ err = rpmsg_send(rpdev, "hello!", 6);
+ if (err) {
+ pr_err("rpmsg_send failed: %d\n", err);
+ return err;
+ }
+
+ return 0;
+ }
+
+ static void rpmsg_sample_remove(struct rpmsg_channel *rpdev)
+ {
+ dev_info(&rpdev->dev, "rpmsg sample client driver is removed\n");
+ }
+
+ static struct rpmsg_device_id rpmsg_driver_sample_id_table[] = {
+ { .name = "rpmsg-client-sample" },
+ { },
+ };
+ MODULE_DEVICE_TABLE(rpmsg, rpmsg_driver_sample_id_table);
+
+ static struct rpmsg_driver rpmsg_sample_client = {
+ .drv.name = KBUILD_MODNAME,
+ .id_table = rpmsg_driver_sample_id_table,
+ .probe = rpmsg_sample_probe,
+ .callback = rpmsg_sample_cb,
+ .remove = rpmsg_sample_remove,
+ };
+ module_rpmsg_driver(rpmsg_sample_client);
+
+.. note::
+
+ a similar sample which can be built and loaded can be found
+ in samples/rpmsg/.
+
+Allocations of rpmsg channels
+=============================
+
+At this point we only support dynamic allocations of rpmsg channels.
+
+This is possible only with remote processors that have the VIRTIO_RPMSG_F_NS
+virtio device feature set. This feature bit means that the remote
+processor supports dynamic name service announcement messages.
+
+When this feature is enabled, creation of rpmsg devices (i.e. channels)
+is completely dynamic: the remote processor announces the existence of a
+remote rpmsg service by sending a name service message (which contains
+the name and rpmsg addr of the remote service, see struct rpmsg_ns_msg).
+
+This message is then handled by the rpmsg bus, which in turn dynamically
+creates and registers an rpmsg channel (which represents the remote service).
+If/when a relevant rpmsg driver is registered, it will be immediately probed
+by the bus, and can then start sending messages to the remote service.
+
+The plan is also to add static creation of rpmsg channels via the virtio
+config space, but it's not implemented yet.
projects / mirror_ubuntu-jammy-kernel.git / commitdiff