#include <linux/mfd/syscon.h>
#include <linux/pinctrl/consumer.h>
-/**
+/*
* If the temperature over a period of time High,
* the resulting TSHUT gave CRU module,let it reset the entire chip,
* or via GPIO give PMIC.
TSHUT_MODE_GPIO,
};
-/**
+/*
* The system Temperature Sensors tshut(tshut) polarity
* the bit 8 is tshut polarity.
* 0: low active, 1: high active
TSHUT_HIGH_ACTIVE,
};
-/**
+/*
* The system has two Temperature Sensors.
* sensor0 is for CPU, and sensor1 is for GPU.
*/
SENSOR_GPU,
};
-/**
+/*
* The conversion table has the adc value and temperature.
* ADC_DECREMENT: the adc value is of diminishing.(e.g. rk3288_code_table)
* ADC_INCREMENT: the adc value is incremental.(e.g. rk3368_code_table)
/**
* struct rockchip_tsadc_chip - hold the private data of tsadc chip
- * @chn_id[SOC_MAX_SENSORS]: the sensor id of chip correspond to the channel
+ * @chn_id: array of sensor ids of chip corresponding to the channel
* @chn_num: the channel number of tsadc chip
* @tshut_temp: the hardware-controlled shutdown temperature value
* @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO)
* @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH)
* @initialize: SoC special initialize tsadc controller method
* @irq_ack: clear the interrupt
+ * @control: enable/disable method for the tsadc controller
* @get_temp: get the temperature
* @set_alarm_temp: set the high temperature interrupt
* @set_tshut_temp: set the hardware-controlled shutdown temperature
* @chip: pointer to the platform/configuration data
* @pdev: platform device of thermal
* @reset: the reset controller of tsadc
- * @sensors[SOC_MAX_SENSORS]: the thermal sensor
+ * @sensors: array of thermal sensors
* @clk: the controller clock is divided by the exteral 24MHz
* @pclk: the advanced peripherals bus clock
* @grf: the general register file will be used to do static set by software
/**
* rk_tsadcv2_initialize - initialize TASDC Controller.
+ * @grf: the general register file will be used to do static set by software
+ * @regs: the base address of tsadc controller
+ * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH)
*
* (1) Set TSADC_V2_AUTO_PERIOD:
* Configure the interleave between every two accessing of
/**
* rk_tsadcv3_initialize - initialize TASDC Controller.
+ * @grf: the general register file will be used to do static set by software
+ * @regs: the base address of tsadc controller
+ * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH)
*
* (1) The tsadc control power sequence.
*
/**
* rk_tsadcv3_control - the tsadc controller is enabled or disabled.
+ * @regs: the base address of tsadc controller
+ * @enable: boolean flag to enable the controller
*
* NOTE: TSADC controller works at auto mode, and some SoCs need set the
* tsadc_q_sel bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output
/**
* Reset TSADC Controller, reset all tsadc registers.
+ * @reset: the reset controller of tsadc
*/
static void rockchip_thermal_reset_controller(struct reset_control *reset)
{