*/
#include <linux/gpio.h>
#include <linux/platform_device.h>
-
+#include <linux/platform_data/gpio-omap.h>
#include <linux/i2c/tps65010.h>
-#include <plat/mmc.h>
-
#include "board-h2.h"
+#include "mmc.h"
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
#include <linux/i2c/tps65010.h>
-#include <plat/mmc.h>
-
#include "board-h3.h"
+#include "mmc.h"
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
#include <asm/mach/arch.h>
#include <mach/omap7xx.h>
-#include <plat/mmc.h>
+#include "mmc.h"
#include <mach/irqs.h>
#include <mach/usb.h>
#include <plat/fpga.h>
#include <plat/tc.h>
#include <linux/platform_data/keypad-omap.h>
-#include <plat/mmc.h>
#include <mach/hardware.h>
#include <mach/usb.h>
#include "iomap.h"
#include "common.h"
+#include "mmc.h"
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define INNOVATOR1610_ETHR_START 0x04000300
#include <asm/mach/map.h>
#include <mach/mux.h>
-#include <plat/mmc.h>
#include <plat/clock.h>
#include <mach/hardware.h>
#include <mach/usb.h>
#include "common.h"
+#include "mmc.h"
#define ADS7846_PENDOWN_GPIO 15
#include <linux/platform_device.h>
#include <mach/hardware.h>
-#include <plat/mmc.h>
#include <mach/board-sx1.h>
+#include "mmc.h"
+
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
static int mmc_set_power(struct device *dev, int slot, int power_on,
#include <plat/tc.h>
#include <mach/mux.h>
#include <plat/dma.h>
-#include <plat/mmc.h>
#include <mach/omap7xx.h>
#include <mach/camera.h>
#include "common.h"
#include "clock.h"
+#include "mmc.h"
#if defined(CONFIG_SND_SOC) || defined(CONFIG_SND_SOC_MODULE)
--- /dev/null
+#include <linux/mmc/host.h>
+#include <linux/platform_data/mmc-omap.h>
+
+#define OMAP15XX_NR_MMC 1
+#define OMAP16XX_NR_MMC 2
+#define OMAP1_MMC_SIZE 0x080
+#define OMAP1_MMC1_BASE 0xfffb7800
+#define OMAP1_MMC2_BASE 0xfffb7c00 /* omap16xx only */
+
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers);
+#else
+static inline void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers)
+{
+}
+#endif
#include "common.h"
#include <plat/usb.h>
-#include <plat/mmc.h>
#include "omap4-keypad.h"
#include <video/omapdss.h>
#include <video/omap-panel-nokia-dsi.h>
#include "soc.h"
#include "mux.h"
+#include "mmc.h"
#include "hsmmc.h"
#include "control.h"
#include "common-board-devices.h"
#include "common.h"
#include <plat/menelaus.h>
-#include <plat/mmc.h>
+#include "mmc.h"
#include "mux.h"
#include "common.h"
#include <plat/usb.h>
-#include <plat/mmc.h>
#include <video/omap-panel-tfp410.h>
#include "soc.h"
+#include "mmc.h"
#include "hsmmc.h"
#include "control.h"
#include "mux.h"
#include <asm/mach-types.h>
#include <plat/i2c.h>
-#include <plat/mmc.h>
#include <plat/usb.h>
#include <plat/gpmc.h>
#include "common.h"
#include <plat/serial.h>
#include "mux.h"
+#include "mmc.h"
#include "hsmmc.h"
#include "sdram-nokia.h"
#include "common-board-devices.h"
#include <mach/hardware.h>
#include <linux/platform_data/gpio-omap.h>
-#include <plat/mmc.h>
#include <plat/omap-pm.h>
#include <plat/omap_device.h>
#include "mux.h"
+#include "mmc.h"
#include "hsmmc.h"
#include "control.h"
--- /dev/null
+#include <linux/mmc/host.h>
+#include <linux/platform_data/mmc-omap.h>
+
+#define OMAP24XX_NR_MMC 2
+#define OMAP2420_MMC_SIZE OMAP1_MMC_SIZE
+#define OMAP2_MMC1_BASE 0x4809c000
+
+#define OMAP4_MMC_REG_OFFSET 0x100
+
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data);
+#else
+static inline void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
+{
+}
+#endif
+
+struct omap_hwmod;
+int omap_msdi_reset(struct omap_hwmod *oh);
+
+/* called from board-specific card detection service routine */
+extern void omap_mmc_notify_cover_event(struct device *dev, int slot,
+ int is_closed);
#include <plat/omap_hwmod.h>
#include <plat/omap_device.h>
-#include <plat/mmc.h>
#include "common.h"
#include "control.h"
#include "mux.h"
+#include "mmc.h"
/*
* MSDI_CON_OFFSET: offset in bytes of the MSDI IP block's CON register
#include <plat/sram.h>
#include <plat/omap-secure.h>
-#include <plat/mmc.h>
#include "omap-wakeupgen.h"
#include "soc.h"
#include "common.h"
+#include "mmc.h"
#include "hsmmc.h"
#include "omap4-sar-layout.h"
#include <plat/dmtimer.h>
#include "l3_2xxx.h"
#include "l4_2xxx.h"
-#include <plat/mmc.h>
#include "omap_hwmod_common_data.h"
#include "cm-regbits-24xx.h"
#include "prm-regbits-24xx.h"
+#include "mmc.h"
#include "wd_timer.h"
/*
#include <plat/serial.h>
#include <plat/i2c.h>
#include <plat/dmtimer.h>
-#include <plat/mmc.h>
+#include "mmc.h"
#include "l3_2xxx.h"
#include "soc.h"
#include <linux/platform_data/gpio-omap.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <plat/dma.h>
-#include <plat/mmc.h>
#include <plat/i2c.h>
#include "omap_hwmod_common_data.h"
#include "cm33xx.h"
#include "prm33xx.h"
#include "prm-regbits-33xx.h"
+#include "mmc.h"
/*
* IP blocks
#include "l3_3xxx.h"
#include "l4_3xxx.h"
#include <plat/i2c.h>
-#include <plat/mmc.h>
#include <linux/platform_data/asoc-ti-mcbsp.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <plat/dmtimer.h>
#include "omap_hwmod_common_data.h"
#include "prm-regbits-34xx.h"
#include "cm-regbits-34xx.h"
+#include "mmc.h"
#include "wd_timer.h"
/*
#include <plat/dma.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <linux/platform_data/asoc-ti-mcbsp.h>
-#include <plat/mmc.h>
#include <plat/dmtimer.h>
#include <plat/common.h>
#include <plat/iommu.h>
#include "cm2_44xx.h"
#include "prm44xx.h"
#include "prm-regbits-44xx.h"
+#include "mmc.h"
#include "wd_timer.h"
/* Base offset for all OMAP4 interrupts external to MPUSS */
+++ /dev/null
-/*
- * MMC definitions for OMAP2
- *
- * Copyright (C) 2006 Nokia Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __OMAP2_MMC_H
-#define __OMAP2_MMC_H
-
-#include <linux/types.h>
-#include <linux/device.h>
-#include <linux/mmc/host.h>
-
-#include <plat/omap_hwmod.h>
-
-#define OMAP15XX_NR_MMC 1
-#define OMAP16XX_NR_MMC 2
-#define OMAP1_MMC_SIZE 0x080
-#define OMAP1_MMC1_BASE 0xfffb7800
-#define OMAP1_MMC2_BASE 0xfffb7c00 /* omap16xx only */
-
-#define OMAP24XX_NR_MMC 2
-#define OMAP2420_MMC_SIZE OMAP1_MMC_SIZE
-#define OMAP2_MMC1_BASE 0x4809c000
-
-#define OMAP4_MMC_REG_OFFSET 0x100
-
-#define OMAP_MMC_MAX_SLOTS 2
-
-/*
- * struct omap_mmc_dev_attr.flags possibilities
- *
- * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can
- * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag
- * should be set if this is the case. See for example Section 22.5.3
- * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia
- * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R).
- *
- * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers
- * don't work correctly on some MMC controller instances on some
- * OMAP3 SoCs; this flag should be set if this is the case. See
- * for example Advisory 2.1.1.128 "MMC: Multiple Block Read
- * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
- * Revision F (October 2010) (SPRZ278F).
- */
-#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0)
-#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1)
-
-struct omap_mmc_dev_attr {
- u8 flags;
-};
-
-struct omap_mmc_platform_data {
- /* back-link to device */
- struct device *dev;
-
- /* number of slots per controller */
- unsigned nr_slots:2;
-
- /* set if your board has components or wiring that limits the
- * maximum frequency on the MMC bus */
- unsigned int max_freq;
-
- /* switch the bus to a new slot */
- int (*switch_slot)(struct device *dev, int slot);
- /* initialize board-specific MMC functionality, can be NULL if
- * not supported */
- int (*init)(struct device *dev);
- void (*cleanup)(struct device *dev);
- void (*shutdown)(struct device *dev);
-
- /* To handle board related suspend/resume functionality for MMC */
- int (*suspend)(struct device *dev, int slot);
- int (*resume)(struct device *dev, int slot);
-
- /* Return context loss count due to PM states changing */
- int (*get_context_loss_count)(struct device *dev);
-
- /* Integrating attributes from the omap_hwmod layer */
- u8 controller_flags;
-
- /* Register offset deviation */
- u16 reg_offset;
-
- struct omap_mmc_slot_data {
-
- /*
- * 4/8 wires and any additional host capabilities
- * need to OR'd all capabilities (ref. linux/mmc/host.h)
- */
- u8 wires; /* Used for the MMC driver on omap1 and 2420 */
- u32 caps; /* Used for the MMC driver on 2430 and later */
- u32 pm_caps; /* PM capabilities of the mmc */
-
- /*
- * nomux means "standard" muxing is wrong on this board, and
- * that board-specific code handled it before common init logic.
- */
- unsigned nomux:1;
-
- /* switch pin can be for card detect (default) or card cover */
- unsigned cover:1;
-
- /* use the internal clock */
- unsigned internal_clock:1;
-
- /* nonremovable e.g. eMMC */
- unsigned nonremovable:1;
-
- /* Try to sleep or power off when possible */
- unsigned power_saving:1;
-
- /* If using power_saving and the MMC power is not to go off */
- unsigned no_off:1;
-
- /* eMMC does not handle power off when not in sleep state */
- unsigned no_regulator_off_init:1;
-
- /* Regulator off remapped to sleep */
- unsigned vcc_aux_disable_is_sleep:1;
-
- /* we can put the features above into this variable */
-#define HSMMC_HAS_PBIAS (1 << 0)
-#define HSMMC_HAS_UPDATED_RESET (1 << 1)
- unsigned features;
-
- int switch_pin; /* gpio (card detect) */
- int gpio_wp; /* gpio (write protect) */
-
- int (*set_bus_mode)(struct device *dev, int slot, int bus_mode);
- int (*set_power)(struct device *dev, int slot,
- int power_on, int vdd);
- int (*get_ro)(struct device *dev, int slot);
- void (*remux)(struct device *dev, int slot, int power_on);
- /* Call back before enabling / disabling regulators */
- void (*before_set_reg)(struct device *dev, int slot,
- int power_on, int vdd);
- /* Call back after enabling / disabling regulators */
- void (*after_set_reg)(struct device *dev, int slot,
- int power_on, int vdd);
- /* if we have special card, init it using this callback */
- void (*init_card)(struct mmc_card *card);
-
- /* return MMC cover switch state, can be NULL if not supported.
- *
- * possible return values:
- * 0 - closed
- * 1 - open
- */
- int (*get_cover_state)(struct device *dev, int slot);
-
- const char *name;
- u32 ocr_mask;
-
- /* Card detection IRQs */
- int card_detect_irq;
- int (*card_detect)(struct device *dev, int slot);
-
- unsigned int ban_openended:1;
-
- } slots[OMAP_MMC_MAX_SLOTS];
-};
-
-/* called from board-specific card detection service routine */
-extern void omap_mmc_notify_cover_event(struct device *dev, int slot,
- int is_closed);
-
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
-void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
- int nr_controllers);
-void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data);
-#else
-static inline void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
- int nr_controllers)
-{
-}
-static inline void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
-{
-}
-#endif
-
-extern int omap_msdi_reset(struct omap_hwmod *oh);
-
-#endif
#include <linux/clk.h>
#include <linux/scatterlist.h>
#include <linux/slab.h>
+#include <linux/platform_data/mmc-omap.h>
-#include <plat/mmc.h>
+#include <plat/cpu.h>
#include <plat/dma.h>
#define OMAP_MMC_REG_CMD 0x00
#include <linux/gpio.h>
#include <linux/regulator/consumer.h>
#include <linux/pm_runtime.h>
-#include <mach/hardware.h>
-#include <plat/mmc.h>
-#include <plat/cpu.h>
+#include <linux/platform_data/mmc-omap.h>
/* OMAP HSMMC Host Controller Registers */
#define OMAP_HSMMC_SYSSTATUS 0x0014
--- /dev/null
+/*
+ * MMC definitions for OMAP2
+ *
+ * Copyright (C) 2006 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define OMAP_MMC_MAX_SLOTS 2
+
+/*
+ * struct omap_mmc_dev_attr.flags possibilities
+ *
+ * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can
+ * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag
+ * should be set if this is the case. See for example Section 22.5.3
+ * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia
+ * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R).
+ *
+ * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers
+ * don't work correctly on some MMC controller instances on some
+ * OMAP3 SoCs; this flag should be set if this is the case. See
+ * for example Advisory 2.1.1.128 "MMC: Multiple Block Read
+ * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
+ * Revision F (October 2010) (SPRZ278F).
+ */
+#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0)
+#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1)
+
+struct mmc_card;
+
+struct omap_mmc_dev_attr {
+ u8 flags;
+};
+
+struct omap_mmc_platform_data {
+ /* back-link to device */
+ struct device *dev;
+
+ /* number of slots per controller */
+ unsigned nr_slots:2;
+
+ /* set if your board has components or wiring that limits the
+ * maximum frequency on the MMC bus */
+ unsigned int max_freq;
+
+ /* switch the bus to a new slot */
+ int (*switch_slot)(struct device *dev, int slot);
+ /* initialize board-specific MMC functionality, can be NULL if
+ * not supported */
+ int (*init)(struct device *dev);
+ void (*cleanup)(struct device *dev);
+ void (*shutdown)(struct device *dev);
+
+ /* To handle board related suspend/resume functionality for MMC */
+ int (*suspend)(struct device *dev, int slot);
+ int (*resume)(struct device *dev, int slot);
+
+ /* Return context loss count due to PM states changing */
+ int (*get_context_loss_count)(struct device *dev);
+
+ /* Integrating attributes from the omap_hwmod layer */
+ u8 controller_flags;
+
+ /* Register offset deviation */
+ u16 reg_offset;
+
+ struct omap_mmc_slot_data {
+
+ /*
+ * 4/8 wires and any additional host capabilities
+ * need to OR'd all capabilities (ref. linux/mmc/host.h)
+ */
+ u8 wires; /* Used for the MMC driver on omap1 and 2420 */
+ u32 caps; /* Used for the MMC driver on 2430 and later */
+ u32 pm_caps; /* PM capabilities of the mmc */
+
+ /*
+ * nomux means "standard" muxing is wrong on this board, and
+ * that board-specific code handled it before common init logic.
+ */
+ unsigned nomux:1;
+
+ /* switch pin can be for card detect (default) or card cover */
+ unsigned cover:1;
+
+ /* use the internal clock */
+ unsigned internal_clock:1;
+
+ /* nonremovable e.g. eMMC */
+ unsigned nonremovable:1;
+
+ /* Try to sleep or power off when possible */
+ unsigned power_saving:1;
+
+ /* If using power_saving and the MMC power is not to go off */
+ unsigned no_off:1;
+
+ /* eMMC does not handle power off when not in sleep state */
+ unsigned no_regulator_off_init:1;
+
+ /* Regulator off remapped to sleep */
+ unsigned vcc_aux_disable_is_sleep:1;
+
+ /* we can put the features above into this variable */
+#define HSMMC_HAS_PBIAS (1 << 0)
+#define HSMMC_HAS_UPDATED_RESET (1 << 1)
+ unsigned features;
+
+ int switch_pin; /* gpio (card detect) */
+ int gpio_wp; /* gpio (write protect) */
+
+ int (*set_bus_mode)(struct device *dev, int slot, int bus_mode);
+ int (*set_power)(struct device *dev, int slot,
+ int power_on, int vdd);
+ int (*get_ro)(struct device *dev, int slot);
+ void (*remux)(struct device *dev, int slot, int power_on);
+ /* Call back before enabling / disabling regulators */
+ void (*before_set_reg)(struct device *dev, int slot,
+ int power_on, int vdd);
+ /* Call back after enabling / disabling regulators */
+ void (*after_set_reg)(struct device *dev, int slot,
+ int power_on, int vdd);
+ /* if we have special card, init it using this callback */
+ void (*init_card)(struct mmc_card *card);
+
+ /* return MMC cover switch state, can be NULL if not supported.
+ *
+ * possible return values:
+ * 0 - closed
+ * 1 - open
+ */
+ int (*get_cover_state)(struct device *dev, int slot);
+
+ const char *name;
+ u32 ocr_mask;
+
+ /* Card detection IRQs */
+ int card_detect_irq;
+ int (*card_detect)(struct device *dev, int slot);
+
+ unsigned int ban_openended:1;
+
+ } slots[OMAP_MMC_MAX_SLOTS];
+};
projects / mirror_ubuntu-zesty-kernel.git / commitdiff