EXPORT_SYMBOL(ASSABET_BCR_frob);
+ static void assabet_ucb1x00_reset(enum ucb1x00_reset state)
+ {
+ if (state == UCB_RST_PROBE)
+ ASSABET_BCR_set(ASSABET_BCR_CODEC_RST);
+ }
+
-static void assabet_backlight_power(int on)
-{
-#ifndef ASSABET_PAL_VIDEO
- if (on)
- ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
- else
-#endif
- ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
-}
-
-/*
- * Turn on/off the backlight. When turning the backlight on,
- * we wait 500us after turning it on so we don't cause the
- * supplies to droop when we enable the LCD controller (and
- * cause a hard reset.)
- */
-static void assabet_lcd_power(int on)
-{
-#ifndef ASSABET_PAL_VIDEO
- if (on) {
- ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
- udelay(500);
- } else
-#endif
- ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
-}
-
-
/*
* Assabet flash support code.
*/
static struct mcp_plat_data assabet_mcp_data = {
.mccr0 = MCCR0_ADM,
.sclk_rate = 11981000,
+ .codec_pdata = &assabet_ucb1x00_data,
};
+static void assabet_lcd_set_visual(u32 visual)
+{
+ u_int is_true_color = visual == FB_VISUAL_TRUECOLOR;
+
+ if (machine_is_assabet()) {
+#if 1 // phase 4 or newer Assabet's
+ if (is_true_color)
+ ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
+ else
+ ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
+#else
+ // older Assabet's
+ if (is_true_color)
+ ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
+ else
+ ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
+#endif
+ }
+}
+
+#ifndef ASSABET_PAL_VIDEO
+static void assabet_lcd_backlight_power(int on)
+{
+ if (on)
+ ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
+ else
+ ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+/*
+ * Turn on/off the backlight. When turning the backlight on, we wait
+ * 500us after turning it on so we don't cause the supplies to droop
+ * when we enable the LCD controller (and cause a hard reset.)
+ */
+static void assabet_lcd_power(int on)
+{
+ if (on) {
+ ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
+ udelay(500);
+ } else
+ ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+/*
+ * The assabet uses a sharp LQ039Q2DS54 LCD module. It is actually
+ * takes an RGB666 signal, but we provide it with an RGB565 signal
+ * instead (def_rgb_16).
+ */
+static struct sa1100fb_mach_info lq039q2ds54_info = {
+ .pixclock = 171521, .bpp = 16,
+ .xres = 320, .yres = 240,
+
+ .hsync_len = 5, .vsync_len = 1,
+ .left_margin = 61, .upper_margin = 3,
+ .right_margin = 9, .lower_margin = 0,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+ .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+ .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+
+ .backlight_power = assabet_lcd_backlight_power,
+ .lcd_power = assabet_lcd_power,
+ .set_visual = assabet_lcd_set_visual,
+};
+#else
+static void assabet_pal_backlight_power(int on)
+{
+ ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+static void assabet_pal_power(int on)
+{
+ ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+static struct sa1100fb_mach_info pal_info = {
+ .pixclock = 67797, .bpp = 16,
+ .xres = 640, .yres = 512,
+
+ .hsync_len = 64, .vsync_len = 6,
+ .left_margin = 125, .upper_margin = 70,
+ .right_margin = 115, .lower_margin = 36,
+
+ .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+ .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
+
+ .backlight_power = assabet_pal_backlight_power,
+ .lcd_power = assabet_pal_power,
+ .set_visual = assabet_lcd_set_visual,
+};
+#endif
+
+#ifdef CONFIG_ASSABET_NEPONSET
+static struct resource neponset_resources[] = {
+ DEFINE_RES_MEM(0x10000000, 0x08000000),
+ DEFINE_RES_MEM(0x18000000, 0x04000000),
+ DEFINE_RES_MEM(0x40000000, SZ_8K),
+ DEFINE_RES_IRQ(IRQ_GPIO25),
+};
+#endif
+
static void __init assabet_init(void)
{
/*
PPDR |= PPC_TXD3 | PPC_TXD1;
PPSR |= PPC_TXD3 | PPC_TXD1;
- sa1100fb_lcd_power = assabet_lcd_power;
- sa1100fb_backlight_power = assabet_backlight_power;
-
+ sa11x0_ppc_configure_mcp();
+
if (machine_has_neponset()) {
/*
* Angel sets this, but other bootloaders may not.
GPSR |= _COLLIE_GPIO_UCB1x00_RESET;
+ collie_power_resource[0].start = gpio_to_irq(COLLIE_GPIO_AC_IN);
+ collie_power_resource[0].end = gpio_to_irq(COLLIE_GPIO_AC_IN);
++
+ sa11x0_ppc_configure_mcp();
+
+
platform_scoop_config = &collie_pcmcia_config;
ret = platform_add_devices(devices, ARRAY_SIZE(devices));
};
static struct resource sa11x0mcp_resources[] = {
- [0] = {
- .start = __PREG(Ser4MCCR0),
- .end = __PREG(Ser4MCCR0) + 0xffff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = __PREG(Ser4MCCR1),
- .end = __PREG(Ser4MCCR1) + 4 - 1,
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .start = IRQ_Ser4MCP,
- .end = IRQ_Ser4MCP,
- .flags = IORESOURCE_IRQ,
- },
+ [0] = DEFINE_RES_MEM(__PREG(Ser4MCCR0), SZ_64K),
- [1] = DEFINE_RES_IRQ(IRQ_Ser4MCP),
++ [1] = DEFINE_RES_MEM(__PREG(Ser4MCCR1), 4),
++ [2] = DEFINE_RES_IRQ(IRQ_Ser4MCP),
};
static u64 sa11x0mcp_dma_mask = 0xffffffffUL;
void sa11x0_register_irda(struct irda_platform_data *irda);
struct mcp_plat_data;
+ void sa11x0_ppc_configure_mcp(void);
void sa11x0_register_mcp(struct mcp_plat_data *data);
+
+struct sa1100fb_mach_info;
+void sa11x0_register_lcd(struct sa1100fb_mach_info *inf);
.sclk_rate = 11981000,
};
+#ifdef LART_GREY_LCD
+static struct sa1100fb_mach_info lart_grey_info = {
+ .pixclock = 150000, .bpp = 4,
+ .xres = 320, .yres = 240,
+
+ .hsync_len = 1, .vsync_len = 1,
+ .left_margin = 4, .upper_margin = 0,
+ .right_margin = 2, .lower_margin = 0,
+
+ .cmap_greyscale = 1,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+ .lccr0 = LCCR0_Mono | LCCR0_Sngl | LCCR0_Pas | LCCR0_4PixMono,
+ .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
+};
+#endif
+#ifdef LART_COLOR_LCD
+static struct sa1100fb_mach_info lart_color_info = {
+ .pixclock = 150000, .bpp = 16,
+ .xres = 320, .yres = 240,
+
+ .hsync_len = 2, .vsync_len = 3,
+ .left_margin = 69, .upper_margin = 14,
+ .right_margin = 8, .lower_margin = 4,
+
+ .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+ .lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
+};
+#endif
+#ifdef LART_VIDEO_OUT
+static struct sa1100fb_mach_info lart_video_info = {
+ .pixclock = 39721, .bpp = 16,
+ .xres = 640, .yres = 480,
+
+ .hsync_len = 95, .vsync_len = 2,
+ .left_margin = 40, .upper_margin = 32,
+ .right_margin = 24, .lower_margin = 11,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+ .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+ .lccr3 = LCCR3_OutEnL | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
+};
+#endif
+
+#ifdef LART_KIT01_LCD
+static struct sa1100fb_mach_info lart_kit01_info = {
+ .pixclock = 63291, .bpp = 16,
+ .xres = 640, .yres = 480,
+
+ .hsync_len = 64, .vsync_len = 3,
+ .left_margin = 122, .upper_margin = 45,
+ .right_margin = 10, .lower_margin = 10,
+
+ .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+ .lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg
+};
+#endif
+
static void __init lart_init(void)
{
+ struct sa1100fb_mach_info *inf = NULL;
+
+#ifdef LART_GREY_LCD
+ inf = &lart_grey_info;
+#endif
+#ifdef LART_COLOR_LCD
+ inf = &lart_color_info;
+#endif
+#ifdef LART_VIDEO_OUT
+ inf = &lart_video_info;
+#endif
+#ifdef LART_KIT01_LCD
+ inf = &lart_kit01_info;
+#endif
+
+ if (inf)
+ sa11x0_register_lcd(inf);
+
+ sa11x0_ppc_configure_mcp();
sa11x0_register_mcp(&lart_mcp_data);
}
.sclk_rate = 11981000,
};
+static struct sa1100fb_mach_info shannon_lcd_info = {
+ .pixclock = 152500, .bpp = 8,
+ .xres = 640, .yres = 480,
+
+ .hsync_len = 4, .vsync_len = 3,
+ .left_margin = 2, .upper_margin = 0,
+ .right_margin = 1, .lower_margin = 0,
+
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+ .lccr0 = LCCR0_Color | LCCR0_Dual | LCCR0_Pas,
+ .lccr3 = LCCR3_ACBsDiv(512),
+};
+
static void __init shannon_init(void)
{
+ sa11x0_ppc_configure_mcp();
+ sa11x0_register_lcd(&shannon_lcd_info);
sa11x0_register_mtd(&shannon_flash_data, &shannon_flash_resource, 1);
sa11x0_register_mcp(&shannon_mcp_data);
}
static struct resource simpad_flash_resources [] = {
- {
- .start = SA1100_CS0_PHYS,
- .end = SA1100_CS0_PHYS + SZ_16M -1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = SA1100_CS1_PHYS,
- .end = SA1100_CS1_PHYS + SZ_16M -1,
- .flags = IORESOURCE_MEM,
- }
+ DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_16M),
+ DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_16M),
};
+ static struct ucb1x00_plat_data simpad_ucb1x00_data = {
+ .gpio_base = SIMPAD_UCB1X00_GPIO_BASE,
+ };
+
static struct mcp_plat_data simpad_mcp_data = {
.mccr0 = MCCR0_ADM,
.sclk_rate = 11981000,
projects / mirror_ubuntu-disco-kernel.git / commitdiff