#define HUB_ROOT_RESET_TIME 50 /* times are in msec */
#define HUB_SHORT_RESET_TIME 10
+#define HUB_BH_RESET_TIME 50
#define HUB_LONG_RESET_TIME 200
#define HUB_RESET_TIMEOUT 500
static int hub_port_wait_reset(struct usb_hub *hub, int port1,
- struct usb_device *udev, unsigned int delay)
+ struct usb_device *udev, unsigned int delay, bool warm)
{
int delay_time, ret;
u16 portstatus;
if (ret < 0)
return ret;
- /* Device went away? */
- if (!(portstatus & USB_PORT_STAT_CONNECTION))
- return -ENOTCONN;
-
- /* bomb out completely if the connection bounced */
- if ((portchange & USB_PORT_STAT_C_CONNECTION))
- return -ENOTCONN;
-
- /* if we`ve finished resetting, then break out of the loop */
- if (!(portstatus & USB_PORT_STAT_RESET) &&
- (portstatus & USB_PORT_STAT_ENABLE)) {
- if (hub_is_wusb(hub))
- udev->speed = USB_SPEED_WIRELESS;
- else if (hub_is_superspeed(hub->hdev))
- udev->speed = USB_SPEED_SUPER;
- else if (portstatus & USB_PORT_STAT_HIGH_SPEED)
- udev->speed = USB_SPEED_HIGH;
- else if (portstatus & USB_PORT_STAT_LOW_SPEED)
- udev->speed = USB_SPEED_LOW;
- else
- udev->speed = USB_SPEED_FULL;
- return 0;
+ /*
+ * Some buggy devices require a warm reset to be issued even
+ * when the port appears not to be connected.
+ */
+ if (!warm) {
+ /* Device went away? */
+ if (!(portstatus & USB_PORT_STAT_CONNECTION))
+ return -ENOTCONN;
+
+ /* bomb out completely if the connection bounced */
+ if ((portchange & USB_PORT_STAT_C_CONNECTION))
+ return -ENOTCONN;
+
+ /* if we`ve finished resetting, then break out of
+ * the loop
+ */
+ if (!(portstatus & USB_PORT_STAT_RESET) &&
+ (portstatus & USB_PORT_STAT_ENABLE)) {
+ if (hub_is_wusb(hub))
+ udev->speed = USB_SPEED_WIRELESS;
+ else if (hub_is_superspeed(hub->hdev))
+ udev->speed = USB_SPEED_SUPER;
+ else if (portstatus & USB_PORT_STAT_HIGH_SPEED)
+ udev->speed = USB_SPEED_HIGH;
+ else if (portstatus & USB_PORT_STAT_LOW_SPEED)
+ udev->speed = USB_SPEED_LOW;
+ else
+ udev->speed = USB_SPEED_FULL;
+ return 0;
+ }
+ } else {
+ if (portchange & USB_PORT_STAT_C_BH_RESET)
+ return 0;
}
/* switch to the long delay after two short delay failures */
delay = HUB_LONG_RESET_TIME;
dev_dbg (hub->intfdev,
- "port %d not reset yet, waiting %dms\n",
- port1, delay);
+ "port %d not %sreset yet, waiting %dms\n",
+ port1, warm ? "warm " : "", delay);
}
return -EBUSY;
}
+static void hub_port_finish_reset(struct usb_hub *hub, int port1,
+ struct usb_device *udev, int *status, bool warm)
+{
+ switch (*status) {
+ case 0:
+ if (!warm) {
+ struct usb_hcd *hcd;
+ /* TRSTRCY = 10 ms; plus some extra */
+ msleep(10 + 40);
+ update_devnum(udev, 0);
+ hcd = bus_to_hcd(udev->bus);
+ if (hcd->driver->reset_device) {
+ *status = hcd->driver->reset_device(hcd, udev);
+ if (*status < 0) {
+ dev_err(&udev->dev, "Cannot reset "
+ "HCD device state\n");
+ break;
+ }
+ }
+ }
+ /* FALL THROUGH */
+ case -ENOTCONN:
+ case -ENODEV:
+ clear_port_feature(hub->hdev,
+ port1, USB_PORT_FEAT_C_RESET);
+ /* FIXME need disconnect() for NOTATTACHED device */
+ if (warm) {
+ clear_port_feature(hub->hdev, port1,
+ USB_PORT_FEAT_C_BH_PORT_RESET);
+ clear_port_feature(hub->hdev, port1,
+ USB_PORT_FEAT_C_PORT_LINK_STATE);
+ } else {
+ usb_set_device_state(udev, *status
+ ? USB_STATE_NOTATTACHED
+ : USB_STATE_DEFAULT);
+ }
+ break;
+ }
+}
+
+/* Handle port reset and port warm(BH) reset (for USB3 protocol ports) */
static int hub_port_reset(struct usb_hub *hub, int port1,
- struct usb_device *udev, unsigned int delay)
+ struct usb_device *udev, unsigned int delay, bool warm)
{
int i, status;
- struct usb_hcd *hcd;
- hcd = bus_to_hcd(udev->bus);
- /* Block EHCI CF initialization during the port reset.
- * Some companion controllers don't like it when they mix.
- */
- down_read(&ehci_cf_port_reset_rwsem);
+ if (!warm) {
+ /* Block EHCI CF initialization during the port reset.
+ * Some companion controllers don't like it when they mix.
+ */
+ down_read(&ehci_cf_port_reset_rwsem);
+ } else {
+ if (!hub_is_superspeed(hub->hdev)) {
+ dev_err(hub->intfdev, "only USB3 hub support "
+ "warm reset\n");
+ return -EINVAL;
+ }
+ }
/* Reset the port */
for (i = 0; i < PORT_RESET_TRIES; i++) {
- status = set_port_feature(hub->hdev,
- port1, USB_PORT_FEAT_RESET);
- if (status)
+ status = set_port_feature(hub->hdev, port1, (warm ?
+ USB_PORT_FEAT_BH_PORT_RESET :
+ USB_PORT_FEAT_RESET));
+ if (status) {
dev_err(hub->intfdev,
- "cannot reset port %d (err = %d)\n",
- port1, status);
- else {
- status = hub_port_wait_reset(hub, port1, udev, delay);
+ "cannot %sreset port %d (err = %d)\n",
+ warm ? "warm " : "", port1, status);
+ } else {
+ status = hub_port_wait_reset(hub, port1, udev, delay,
+ warm);
if (status && status != -ENOTCONN)
dev_dbg(hub->intfdev,
"port_wait_reset: err = %d\n",
}
/* return on disconnect or reset */
- switch (status) {
- case 0:
- /* TRSTRCY = 10 ms; plus some extra */
- msleep(10 + 40);
- update_devnum(udev, 0);
- if (hcd->driver->reset_device) {
- status = hcd->driver->reset_device(hcd, udev);
- if (status < 0) {
- dev_err(&udev->dev, "Cannot reset "
- "HCD device state\n");
- break;
- }
- }
- /* FALL THROUGH */
- case -ENOTCONN:
- case -ENODEV:
- clear_port_feature(hub->hdev,
- port1, USB_PORT_FEAT_C_RESET);
- /* FIXME need disconnect() for NOTATTACHED device */
- usb_set_device_state(udev, status
- ? USB_STATE_NOTATTACHED
- : USB_STATE_DEFAULT);
+ if (status == 0 || status == -ENOTCONN || status == -ENODEV) {
+ hub_port_finish_reset(hub, port1, udev, &status, warm);
goto done;
}
dev_dbg (hub->intfdev,
- "port %d not enabled, trying reset again...\n",
- port1);
+ "port %d not enabled, trying %sreset again...\n",
+ port1, warm ? "warm " : "");
delay = HUB_LONG_RESET_TIME;
}
"Cannot enable port %i. Maybe the USB cable is bad?\n",
port1);
- done:
- up_read(&ehci_cf_port_reset_rwsem);
- return status;
-}
-
-/* Warm reset a USB3 protocol port */
-static int hub_port_warm_reset(struct usb_hub *hub, int port)
-{
- int ret;
- u16 portstatus, portchange;
-
- if (!hub_is_superspeed(hub->hdev)) {
- dev_err(hub->intfdev, "only USB3 hub support warm reset\n");
- return -EINVAL;
- }
-
- /* Warm reset the port */
- ret = set_port_feature(hub->hdev,
- port, USB_PORT_FEAT_BH_PORT_RESET);
- if (ret) {
- dev_err(hub->intfdev, "cannot warm reset port %d\n", port);
- return ret;
- }
-
- msleep(20);
- ret = hub_port_status(hub, port, &portstatus, &portchange);
-
- if (portchange & USB_PORT_STAT_C_RESET)
- clear_port_feature(hub->hdev, port, USB_PORT_FEAT_C_RESET);
-
- if (portchange & USB_PORT_STAT_C_BH_RESET)
- clear_port_feature(hub->hdev, port,
- USB_PORT_FEAT_C_BH_PORT_RESET);
-
- if (portchange & USB_PORT_STAT_C_LINK_STATE)
- clear_port_feature(hub->hdev, port,
- USB_PORT_FEAT_C_PORT_LINK_STATE);
+done:
+ if (!warm)
+ up_read(&ehci_cf_port_reset_rwsem);
- return ret;
+ return status;
}
/* Check if a port is power on */
/* Reset the device; full speed may morph to high speed */
/* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */
- retval = hub_port_reset(hub, port1, udev, delay);
+ retval = hub_port_reset(hub, port1, udev, delay, false);
if (retval < 0) /* error or disconnect */
goto fail;
/* success, speed is known */
buf->bMaxPacketSize0;
kfree(buf);
- retval = hub_port_reset(hub, port1, udev, delay);
+ retval = hub_port_reset(hub, port1, udev, delay, false);
if (retval < 0) /* error or disconnect */
goto fail;
if (oldspeed != udev->speed) {
(portstatus & USB_PORT_STAT_LINK_STATE)
== USB_SS_PORT_LS_SS_INACTIVE) {
dev_dbg(hub_dev, "warm reset port %d\n", i);
- hub_port_warm_reset(hub, i);
+ hub_port_reset(hub, i, NULL,
+ HUB_BH_RESET_TIME, true);
}
if (connect_change)
projects / mirror_ubuntu-eoan-kernel.git / commitdiff