sky2: use correct Inter Packet Gap at 10/100mbit

This is another fix picked out of the vendor driver. The IPG value
in the serial mode register is supposed to be programmed differently
at lower speeds.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 3fc8683b2ff030362a3f96f30a6e0257d33f0f07..b1a675a94a17e709e89d096a5edbbd37a62da800 100644 (file)
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -714,6 +714,20 @@ static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port)
        sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
 }
 
+/* configure IPG according to used link speed */
+static void sky2_set_ipg(struct sky2_port *sky2)
+{
+       u16 reg;
+
+       reg = gma_read16(sky2->hw, sky2->port, GM_SERIAL_MODE);
+       reg &= ~GM_SMOD_IPG_MSK;
+       if (sky2->speed > SPEED_100)
+               reg |= IPG_DATA_VAL(IPG_DATA_DEF_1000);
+       else
+               reg |= IPG_DATA_VAL(IPG_DATA_DEF_10_100);
+       gma_write16(sky2->hw, sky2->port, GM_SERIAL_MODE, reg);
+}
+
 /* Enable Rx/Tx */
 static void sky2_enable_rx_tx(struct sky2_port *sky2)
 {
@@ -882,7 +896,7 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
 
        /* serial mode register */
        reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
-               GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+               GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF_1000);
 
        if (hw->dev[port]->mtu > ETH_DATA_LEN)
                reg |= GM_SMOD_JUMBO_ENA;
@@ -2053,6 +2067,8 @@ static void sky2_link_up(struct sky2_port *sky2)
                [FC_BOTH]       = "both",
        };
 
+       sky2_set_ipg(sky2);
+
        sky2_enable_rx_tx(sky2);
 
        gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
@@ -2290,8 +2306,11 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu)
        dev->mtu = new_mtu;
        netdev_update_features(dev);
 
-       mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
-               GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
+       mode = DATA_BLIND_VAL(DATA_BLIND_DEF) | GM_SMOD_VLAN_ENA;
+       if (sky2->speed > SPEED_100)
+               mode |= IPG_DATA_VAL(IPG_DATA_DEF_1000);
+       else
+               mode |= IPG_DATA_VAL(IPG_DATA_DEF_10_100);
 
        if (dev->mtu > ETH_DATA_LEN)
                mode |= GM_SMOD_JUMBO_ENA;

diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index 030221f4ea83d8d60f29aacfc9e9186e9458f8ad..530378a660217aa32ee57f3cd29c0dd663a3588e 100644 (file)
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -1807,10 +1807,11 @@ enum {
 };
 
 #define DATA_BLIND_VAL(x)      (((x)<<11) & GM_SMOD_DATABL_MSK)
-#define DATA_BLIND_DEF         0x04
-
 #define IPG_DATA_VAL(x)                (x & GM_SMOD_IPG_MSK)
-#define IPG_DATA_DEF           0x1e
+
+#define DATA_BLIND_DEF         0x04
+#define IPG_DATA_DEF_1000      0x1e
+#define IPG_DATA_DEF_10_100    0x18
 
 /*     GM_SMI_CTRL                     16 bit r/w      SMI Control Register */
 enum {