To compile this driver as a module, choose M here: the module
will be called starfire. This is recommended.
-config KSZ884X_PCI
- tristate "Micrel KSZ8841/2 PCI"
- depends on NET_PCI && PCI
- select MII
- select CRC32
- help
- This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
-
- To compile this driver as a module, choose M here. The module
- will be called ksz884x.
-
config FORCEDETH
tristate "nForce Ethernet support"
depends on NET_PCI && PCI
Please email feedback to <torben.mathiasen@compaq.com>.
-config KS8842
- tristate "Micrel KSZ8841/42 with generic bus interface"
- depends on HAS_IOMEM && DMA_ENGINE
- help
- This platform driver is for KSZ8841(1-port) / KS8842(2-port)
- ethernet switch chip (managed, VLAN, QoS) from Micrel or
- Timberdale(FPGA).
-
-config KS8851
- tristate "Micrel KS8851 SPI"
- depends on SPI
- select MII
- select CRC32
- help
- SPI driver for Micrel KS8851 SPI attached network chip.
-
-config KS8851_MLL
- tristate "Micrel KS8851 MLL"
- depends on HAS_IOMEM
- select MII
- help
- This platform driver is for Micrel KS8851 Address/data bus
- multiplexed network chip.
-
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
depends on NET_ETHERNET && EXPERIMENTAL && AR7
ps3_gelic-objs += ps3_gelic_net.o $(gelic_wireless-y)
obj-$(CONFIG_TC35815) += tc35815.o
obj-$(CONFIG_SKFP) += skfp/
-obj-$(CONFIG_KS8842) += ks8842.o
-obj-$(CONFIG_KS8851) += ks8851.o
-obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
-obj-$(CONFIG_KSZ884X_PCI) += ksz884x.o
obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
obj-$(CONFIG_RIONET) += rionet.o
obj-$(CONFIG_SH_ETH) += sh_eth.o
If you wish to compile a kernel for the AT91RM9200 and enable
ethernet support, then you should always answer Y to this.
-config ARM_KS8695_ETHER
- tristate "KS8695 Ethernet support"
- depends on ARM && ARCH_KS8695
- select MII
- help
- If you wish to compile a kernel for the KS8695 and want to
- use the internal ethernet then you should answer Y to this.
-
config EP93XX_ETH
tristate "EP93xx Ethernet support"
depends on ARM && ARCH_EP93XX
#
obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o
-obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o
obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o
obj-$(CONFIG_W90P910_ETH) += w90p910_ether.o
+++ /dev/null
-/*
- * Micrel KS8695 (Centaur) Ethernet.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * Copyright 2008 Simtec Electronics
- * Daniel Silverstone <dsilvers@simtec.co.uk>
- * Vincent Sanders <vince@simtec.co.uk>
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/crc32.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <linux/slab.h>
-
-#include <asm/irq.h>
-
-#include <mach/regs-switch.h>
-#include <mach/regs-misc.h>
-#include <asm/mach/irq.h>
-#include <mach/regs-irq.h>
-
-#include "ks8695net.h"
-
-#define MODULENAME "ks8695_ether"
-#define MODULEVERSION "1.02"
-
-/*
- * Transmit and device reset timeout, default 5 seconds.
- */
-static int watchdog = 5000;
-
-/* Hardware structures */
-
-/**
- * struct rx_ring_desc - Receive descriptor ring element
- * @status: The status of the descriptor element (E.g. who owns it)
- * @length: The number of bytes in the block pointed to by data_ptr
- * @data_ptr: The physical address of the data block to receive into
- * @next_desc: The physical address of the next descriptor element.
- */
-struct rx_ring_desc {
- __le32 status;
- __le32 length;
- __le32 data_ptr;
- __le32 next_desc;
-};
-
-/**
- * struct tx_ring_desc - Transmit descriptor ring element
- * @owner: Who owns the descriptor
- * @status: The number of bytes in the block pointed to by data_ptr
- * @data_ptr: The physical address of the data block to receive into
- * @next_desc: The physical address of the next descriptor element.
- */
-struct tx_ring_desc {
- __le32 owner;
- __le32 status;
- __le32 data_ptr;
- __le32 next_desc;
-};
-
-/**
- * struct ks8695_skbuff - sk_buff wrapper for rx/tx rings.
- * @skb: The buffer in the ring
- * @dma_ptr: The mapped DMA pointer of the buffer
- * @length: The number of bytes mapped to dma_ptr
- */
-struct ks8695_skbuff {
- struct sk_buff *skb;
- dma_addr_t dma_ptr;
- u32 length;
-};
-
-/* Private device structure */
-
-#define MAX_TX_DESC 8
-#define MAX_TX_DESC_MASK 0x7
-#define MAX_RX_DESC 16
-#define MAX_RX_DESC_MASK 0xf
-
-/*napi_weight have better more than rx DMA buffers*/
-#define NAPI_WEIGHT 64
-
-#define MAX_RXBUF_SIZE 0x700
-
-#define TX_RING_DMA_SIZE (sizeof(struct tx_ring_desc) * MAX_TX_DESC)
-#define RX_RING_DMA_SIZE (sizeof(struct rx_ring_desc) * MAX_RX_DESC)
-#define RING_DMA_SIZE (TX_RING_DMA_SIZE + RX_RING_DMA_SIZE)
-
-/**
- * enum ks8695_dtype - Device type
- * @KS8695_DTYPE_WAN: This device is a WAN interface
- * @KS8695_DTYPE_LAN: This device is a LAN interface
- * @KS8695_DTYPE_HPNA: This device is an HPNA interface
- */
-enum ks8695_dtype {
- KS8695_DTYPE_WAN,
- KS8695_DTYPE_LAN,
- KS8695_DTYPE_HPNA,
-};
-
-/**
- * struct ks8695_priv - Private data for the KS8695 Ethernet
- * @in_suspend: Flag to indicate if we're suspending/resuming
- * @ndev: The net_device for this interface
- * @dev: The platform device object for this interface
- * @dtype: The type of this device
- * @io_regs: The ioremapped registers for this interface
- * @napi : Add support NAPI for Rx
- * @rx_irq_name: The textual name of the RX IRQ from the platform data
- * @tx_irq_name: The textual name of the TX IRQ from the platform data
- * @link_irq_name: The textual name of the link IRQ from the
- * platform data if available
- * @rx_irq: The IRQ number for the RX IRQ
- * @tx_irq: The IRQ number for the TX IRQ
- * @link_irq: The IRQ number for the link IRQ if available
- * @regs_req: The resource request for the registers region
- * @phyiface_req: The resource request for the phy/switch region
- * if available
- * @phyiface_regs: The ioremapped registers for the phy/switch if available
- * @ring_base: The base pointer of the dma coherent memory for the rings
- * @ring_base_dma: The DMA mapped equivalent of ring_base
- * @tx_ring: The pointer in ring_base of the TX ring
- * @tx_ring_used: The number of slots in the TX ring which are occupied
- * @tx_ring_next_slot: The next slot to fill in the TX ring
- * @tx_ring_dma: The DMA mapped equivalent of tx_ring
- * @tx_buffers: The sk_buff mappings for the TX ring
- * @txq_lock: A lock to protect the tx_buffers tx_ring_used etc variables
- * @rx_ring: The pointer in ring_base of the RX ring
- * @rx_ring_dma: The DMA mapped equivalent of rx_ring
- * @rx_buffers: The sk_buff mappings for the RX ring
- * @next_rx_desc_read: The next RX descriptor to read from on IRQ
- * @rx_lock: A lock to protect Rx irq function
- * @msg_enable: The flags for which messages to emit
- */
-struct ks8695_priv {
- int in_suspend;
- struct net_device *ndev;
- struct device *dev;
- enum ks8695_dtype dtype;
- void __iomem *io_regs;
-
- struct napi_struct napi;
-
- const char *rx_irq_name, *tx_irq_name, *link_irq_name;
- int rx_irq, tx_irq, link_irq;
-
- struct resource *regs_req, *phyiface_req;
- void __iomem *phyiface_regs;
-
- void *ring_base;
- dma_addr_t ring_base_dma;
-
- struct tx_ring_desc *tx_ring;
- int tx_ring_used;
- int tx_ring_next_slot;
- dma_addr_t tx_ring_dma;
- struct ks8695_skbuff tx_buffers[MAX_TX_DESC];
- spinlock_t txq_lock;
-
- struct rx_ring_desc *rx_ring;
- dma_addr_t rx_ring_dma;
- struct ks8695_skbuff rx_buffers[MAX_RX_DESC];
- int next_rx_desc_read;
- spinlock_t rx_lock;
-
- int msg_enable;
-};
-
-/* Register access */
-
-/**
- * ks8695_readreg - Read from a KS8695 ethernet register
- * @ksp: The device to read from
- * @reg: The register to read
- */
-static inline u32
-ks8695_readreg(struct ks8695_priv *ksp, int reg)
-{
- return readl(ksp->io_regs + reg);
-}
-
-/**
- * ks8695_writereg - Write to a KS8695 ethernet register
- * @ksp: The device to write to
- * @reg: The register to write
- * @value: The value to write to the register
- */
-static inline void
-ks8695_writereg(struct ks8695_priv *ksp, int reg, u32 value)
-{
- writel(value, ksp->io_regs + reg);
-}
-
-/* Utility functions */
-
-/**
- * ks8695_port_type - Retrieve port-type as user-friendly string
- * @ksp: The device to return the type for
- *
- * Returns a string indicating which of the WAN, LAN or HPNA
- * ports this device is likely to represent.
- */
-static const char *
-ks8695_port_type(struct ks8695_priv *ksp)
-{
- switch (ksp->dtype) {
- case KS8695_DTYPE_LAN:
- return "LAN";
- case KS8695_DTYPE_WAN:
- return "WAN";
- case KS8695_DTYPE_HPNA:
- return "HPNA";
- }
-
- return "UNKNOWN";
-}
-
-/**
- * ks8695_update_mac - Update the MAC registers in the device
- * @ksp: The device to update
- *
- * Updates the MAC registers in the KS8695 device from the address in the
- * net_device structure associated with this interface.
- */
-static void
-ks8695_update_mac(struct ks8695_priv *ksp)
-{
- /* Update the HW with the MAC from the net_device */
- struct net_device *ndev = ksp->ndev;
- u32 machigh, maclow;
-
- maclow = ((ndev->dev_addr[2] << 24) | (ndev->dev_addr[3] << 16) |
- (ndev->dev_addr[4] << 8) | (ndev->dev_addr[5] << 0));
- machigh = ((ndev->dev_addr[0] << 8) | (ndev->dev_addr[1] << 0));
-
- ks8695_writereg(ksp, KS8695_MAL, maclow);
- ks8695_writereg(ksp, KS8695_MAH, machigh);
-
-}
-
-/**
- * ks8695_refill_rxbuffers - Re-fill the RX buffer ring
- * @ksp: The device to refill
- *
- * Iterates the RX ring of the device looking for empty slots.
- * For each empty slot, we allocate and map a new SKB and give it
- * to the hardware.
- * This can be called from interrupt context safely.
- */
-static void
-ks8695_refill_rxbuffers(struct ks8695_priv *ksp)
-{
- /* Run around the RX ring, filling in any missing sk_buff's */
- int buff_n;
-
- for (buff_n = 0; buff_n < MAX_RX_DESC; ++buff_n) {
- if (!ksp->rx_buffers[buff_n].skb) {
- struct sk_buff *skb = dev_alloc_skb(MAX_RXBUF_SIZE);
- dma_addr_t mapping;
-
- ksp->rx_buffers[buff_n].skb = skb;
- if (skb == NULL) {
- /* Failed to allocate one, perhaps
- * we'll try again later.
- */
- break;
- }
-
- mapping = dma_map_single(ksp->dev, skb->data,
- MAX_RXBUF_SIZE,
- DMA_FROM_DEVICE);
- if (unlikely(dma_mapping_error(ksp->dev, mapping))) {
- /* Failed to DMA map this SKB, try later */
- dev_kfree_skb_irq(skb);
- ksp->rx_buffers[buff_n].skb = NULL;
- break;
- }
- ksp->rx_buffers[buff_n].dma_ptr = mapping;
- skb->dev = ksp->ndev;
- ksp->rx_buffers[buff_n].length = MAX_RXBUF_SIZE;
-
- /* Record this into the DMA ring */
- ksp->rx_ring[buff_n].data_ptr = cpu_to_le32(mapping);
- ksp->rx_ring[buff_n].length =
- cpu_to_le32(MAX_RXBUF_SIZE);
-
- wmb();
-
- /* And give ownership over to the hardware */
- ksp->rx_ring[buff_n].status = cpu_to_le32(RDES_OWN);
- }
- }
-}
-
-/* Maximum number of multicast addresses which the KS8695 HW supports */
-#define KS8695_NR_ADDRESSES 16
-
-/**
- * ks8695_init_partial_multicast - Init the mcast addr registers
- * @ksp: The device to initialise
- * @addr: The multicast address list to use
- * @nr_addr: The number of addresses in the list
- *
- * This routine is a helper for ks8695_set_multicast - it writes
- * the additional-address registers in the KS8695 ethernet device
- * and cleans up any others left behind.
- */
-static void
-ks8695_init_partial_multicast(struct ks8695_priv *ksp,
- struct net_device *ndev)
-{
- u32 low, high;
- int i;
- struct netdev_hw_addr *ha;
-
- i = 0;
- netdev_for_each_mc_addr(ha, ndev) {
- /* Ran out of space in chip? */
- BUG_ON(i == KS8695_NR_ADDRESSES);
-
- low = (ha->addr[2] << 24) | (ha->addr[3] << 16) |
- (ha->addr[4] << 8) | (ha->addr[5]);
- high = (ha->addr[0] << 8) | (ha->addr[1]);
-
- ks8695_writereg(ksp, KS8695_AAL_(i), low);
- ks8695_writereg(ksp, KS8695_AAH_(i), AAH_E | high);
- i++;
- }
-
- /* Clear the remaining Additional Station Addresses */
- for (; i < KS8695_NR_ADDRESSES; i++) {
- ks8695_writereg(ksp, KS8695_AAL_(i), 0);
- ks8695_writereg(ksp, KS8695_AAH_(i), 0);
- }
-}
-
-/* Interrupt handling */
-
-/**
- * ks8695_tx_irq - Transmit IRQ handler
- * @irq: The IRQ which went off (ignored)
- * @dev_id: The net_device for the interrupt
- *
- * Process the TX ring, clearing out any transmitted slots.
- * Allows the net_device to pass us new packets once slots are
- * freed.
- */
-static irqreturn_t
-ks8695_tx_irq(int irq, void *dev_id)
-{
- struct net_device *ndev = (struct net_device *)dev_id;
- struct ks8695_priv *ksp = netdev_priv(ndev);
- int buff_n;
-
- for (buff_n = 0; buff_n < MAX_TX_DESC; ++buff_n) {
- if (ksp->tx_buffers[buff_n].skb &&
- !(ksp->tx_ring[buff_n].owner & cpu_to_le32(TDES_OWN))) {
- rmb();
- /* An SKB which is not owned by HW is present */
- /* Update the stats for the net_device */
- ndev->stats.tx_packets++;
- ndev->stats.tx_bytes += ksp->tx_buffers[buff_n].length;
-
- /* Free the packet from the ring */
- ksp->tx_ring[buff_n].data_ptr = 0;
-
- /* Free the sk_buff */
- dma_unmap_single(ksp->dev,
- ksp->tx_buffers[buff_n].dma_ptr,
- ksp->tx_buffers[buff_n].length,
- DMA_TO_DEVICE);
- dev_kfree_skb_irq(ksp->tx_buffers[buff_n].skb);
- ksp->tx_buffers[buff_n].skb = NULL;
- ksp->tx_ring_used--;
- }
- }
-
- netif_wake_queue(ndev);
-
- return IRQ_HANDLED;
-}
-
-/**
- * ks8695_get_rx_enable_bit - Get rx interrupt enable/status bit
- * @ksp: Private data for the KS8695 Ethernet
- *
- * For KS8695 document:
- * Interrupt Enable Register (offset 0xE204)
- * Bit29 : WAN MAC Receive Interrupt Enable
- * Bit16 : LAN MAC Receive Interrupt Enable
- * Interrupt Status Register (Offset 0xF208)
- * Bit29: WAN MAC Receive Status
- * Bit16: LAN MAC Receive Status
- * So, this Rx interrrupt enable/status bit number is equal
- * as Rx IRQ number.
- */
-static inline u32 ks8695_get_rx_enable_bit(struct ks8695_priv *ksp)
-{
- return ksp->rx_irq;
-}
-
-/**
- * ks8695_rx_irq - Receive IRQ handler
- * @irq: The IRQ which went off (ignored)
- * @dev_id: The net_device for the interrupt
- *
- * Inform NAPI that packet reception needs to be scheduled
- */
-
-static irqreturn_t
-ks8695_rx_irq(int irq, void *dev_id)
-{
- struct net_device *ndev = (struct net_device *)dev_id;
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- spin_lock(&ksp->rx_lock);
-
- if (napi_schedule_prep(&ksp->napi)) {
- unsigned long status = readl(KS8695_IRQ_VA + KS8695_INTEN);
- unsigned long mask_bit = 1 << ks8695_get_rx_enable_bit(ksp);
- /*disable rx interrupt*/
- status &= ~mask_bit;
- writel(status , KS8695_IRQ_VA + KS8695_INTEN);
- __napi_schedule(&ksp->napi);
- }
-
- spin_unlock(&ksp->rx_lock);
- return IRQ_HANDLED;
-}
-
-/**
- * ks8695_rx - Receive packets called by NAPI poll method
- * @ksp: Private data for the KS8695 Ethernet
- * @budget: Number of packets allowed to process
- */
-static int ks8695_rx(struct ks8695_priv *ksp, int budget)
-{
- struct net_device *ndev = ksp->ndev;
- struct sk_buff *skb;
- int buff_n;
- u32 flags;
- int pktlen;
- int received = 0;
-
- buff_n = ksp->next_rx_desc_read;
- while (received < budget
- && ksp->rx_buffers[buff_n].skb
- && (!(ksp->rx_ring[buff_n].status &
- cpu_to_le32(RDES_OWN)))) {
- rmb();
- flags = le32_to_cpu(ksp->rx_ring[buff_n].status);
-
- /* Found an SKB which we own, this means we
- * received a packet
- */
- if ((flags & (RDES_FS | RDES_LS)) !=
- (RDES_FS | RDES_LS)) {
- /* This packet is not the first and
- * the last segment. Therefore it is
- * a "spanning" packet and we can't
- * handle it
- */
- goto rx_failure;
- }
-
- if (flags & (RDES_ES | RDES_RE)) {
- /* It's an error packet */
- ndev->stats.rx_errors++;
- if (flags & RDES_TL)
- ndev->stats.rx_length_errors++;
- if (flags & RDES_RF)
- ndev->stats.rx_length_errors++;
- if (flags & RDES_CE)
- ndev->stats.rx_crc_errors++;
- if (flags & RDES_RE)
- ndev->stats.rx_missed_errors++;
-
- goto rx_failure;
- }
-
- pktlen = flags & RDES_FLEN;
- pktlen -= 4; /* Drop the CRC */
-
- /* Retrieve the sk_buff */
- skb = ksp->rx_buffers[buff_n].skb;
-
- /* Clear it from the ring */
- ksp->rx_buffers[buff_n].skb = NULL;
- ksp->rx_ring[buff_n].data_ptr = 0;
-
- /* Unmap the SKB */
- dma_unmap_single(ksp->dev,
- ksp->rx_buffers[buff_n].dma_ptr,
- ksp->rx_buffers[buff_n].length,
- DMA_FROM_DEVICE);
-
- /* Relinquish the SKB to the network layer */
- skb_put(skb, pktlen);
- skb->protocol = eth_type_trans(skb, ndev);
- netif_receive_skb(skb);
-
- /* Record stats */
- ndev->stats.rx_packets++;
- ndev->stats.rx_bytes += pktlen;
- goto rx_finished;
-
-rx_failure:
- /* This ring entry is an error, but we can
- * re-use the skb
- */
- /* Give the ring entry back to the hardware */
- ksp->rx_ring[buff_n].status = cpu_to_le32(RDES_OWN);
-rx_finished:
- received++;
- buff_n = (buff_n + 1) & MAX_RX_DESC_MASK;
- }
-
- /* And note which RX descriptor we last did */
- ksp->next_rx_desc_read = buff_n;
-
- /* And refill the buffers */
- ks8695_refill_rxbuffers(ksp);
-
- /* Kick the RX DMA engine, in case it became suspended */
- ks8695_writereg(ksp, KS8695_DRSC, 0);
-
- return received;
-}
-
-
-/**
- * ks8695_poll - Receive packet by NAPI poll method
- * @ksp: Private data for the KS8695 Ethernet
- * @budget: The remaining number packets for network subsystem
- *
- * Invoked by the network core when it requests for new
- * packets from the driver
- */
-static int ks8695_poll(struct napi_struct *napi, int budget)
-{
- struct ks8695_priv *ksp = container_of(napi, struct ks8695_priv, napi);
- unsigned long work_done;
-
- unsigned long isr = readl(KS8695_IRQ_VA + KS8695_INTEN);
- unsigned long mask_bit = 1 << ks8695_get_rx_enable_bit(ksp);
-
- work_done = ks8695_rx(ksp, budget);
-
- if (work_done < budget) {
- unsigned long flags;
- spin_lock_irqsave(&ksp->rx_lock, flags);
- __napi_complete(napi);
- /*enable rx interrupt*/
- writel(isr | mask_bit, KS8695_IRQ_VA + KS8695_INTEN);
- spin_unlock_irqrestore(&ksp->rx_lock, flags);
- }
- return work_done;
-}
-
-/**
- * ks8695_link_irq - Link change IRQ handler
- * @irq: The IRQ which went off (ignored)
- * @dev_id: The net_device for the interrupt
- *
- * The WAN interface can generate an IRQ when the link changes,
- * report this to the net layer and the user.
- */
-static irqreturn_t
-ks8695_link_irq(int irq, void *dev_id)
-{
- struct net_device *ndev = (struct net_device *)dev_id;
- struct ks8695_priv *ksp = netdev_priv(ndev);
- u32 ctrl;
-
- ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
- if (ctrl & WMC_WLS) {
- netif_carrier_on(ndev);
- if (netif_msg_link(ksp))
- dev_info(ksp->dev,
- "%s: Link is now up (10%sMbps/%s-duplex)\n",
- ndev->name,
- (ctrl & WMC_WSS) ? "0" : "",
- (ctrl & WMC_WDS) ? "Full" : "Half");
- } else {
- netif_carrier_off(ndev);
- if (netif_msg_link(ksp))
- dev_info(ksp->dev, "%s: Link is now down.\n",
- ndev->name);
- }
-
- return IRQ_HANDLED;
-}
-
-
-/* KS8695 Device functions */
-
-/**
- * ks8695_reset - Reset a KS8695 ethernet interface
- * @ksp: The interface to reset
- *
- * Perform an engine reset of the interface and re-program it
- * with sensible defaults.
- */
-static void
-ks8695_reset(struct ks8695_priv *ksp)
-{
- int reset_timeout = watchdog;
- /* Issue the reset via the TX DMA control register */
- ks8695_writereg(ksp, KS8695_DTXC, DTXC_TRST);
- while (reset_timeout--) {
- if (!(ks8695_readreg(ksp, KS8695_DTXC) & DTXC_TRST))
- break;
- msleep(1);
- }
-
- if (reset_timeout < 0) {
- dev_crit(ksp->dev,
- "Timeout waiting for DMA engines to reset\n");
- /* And blithely carry on */
- }
-
- /* Definitely wait long enough before attempting to program
- * the engines
- */
- msleep(10);
-
- /* RX: unicast and broadcast */
- ks8695_writereg(ksp, KS8695_DRXC, DRXC_RU | DRXC_RB);
- /* TX: pad and add CRC */
- ks8695_writereg(ksp, KS8695_DTXC, DTXC_TEP | DTXC_TAC);
-}
-
-/**
- * ks8695_shutdown - Shut down a KS8695 ethernet interface
- * @ksp: The interface to shut down
- *
- * This disables packet RX/TX, cleans up IRQs, drains the rings,
- * and basically places the interface into a clean shutdown
- * state.
- */
-static void
-ks8695_shutdown(struct ks8695_priv *ksp)
-{
- u32 ctrl;
- int buff_n;
-
- /* Disable packet transmission */
- ctrl = ks8695_readreg(ksp, KS8695_DTXC);
- ks8695_writereg(ksp, KS8695_DTXC, ctrl & ~DTXC_TE);
-
- /* Disable packet reception */
- ctrl = ks8695_readreg(ksp, KS8695_DRXC);
- ks8695_writereg(ksp, KS8695_DRXC, ctrl & ~DRXC_RE);
-
- /* Release the IRQs */
- free_irq(ksp->rx_irq, ksp->ndev);
- free_irq(ksp->tx_irq, ksp->ndev);
- if (ksp->link_irq != -1)
- free_irq(ksp->link_irq, ksp->ndev);
-
- /* Throw away any pending TX packets */
- for (buff_n = 0; buff_n < MAX_TX_DESC; ++buff_n) {
- if (ksp->tx_buffers[buff_n].skb) {
- /* Remove this SKB from the TX ring */
- ksp->tx_ring[buff_n].owner = 0;
- ksp->tx_ring[buff_n].status = 0;
- ksp->tx_ring[buff_n].data_ptr = 0;
-
- /* Unmap and bin this SKB */
- dma_unmap_single(ksp->dev,
- ksp->tx_buffers[buff_n].dma_ptr,
- ksp->tx_buffers[buff_n].length,
- DMA_TO_DEVICE);
- dev_kfree_skb_irq(ksp->tx_buffers[buff_n].skb);
- ksp->tx_buffers[buff_n].skb = NULL;
- }
- }
-
- /* Purge the RX buffers */
- for (buff_n = 0; buff_n < MAX_RX_DESC; ++buff_n) {
- if (ksp->rx_buffers[buff_n].skb) {
- /* Remove the SKB from the RX ring */
- ksp->rx_ring[buff_n].status = 0;
- ksp->rx_ring[buff_n].data_ptr = 0;
-
- /* Unmap and bin the SKB */
- dma_unmap_single(ksp->dev,
- ksp->rx_buffers[buff_n].dma_ptr,
- ksp->rx_buffers[buff_n].length,
- DMA_FROM_DEVICE);
- dev_kfree_skb_irq(ksp->rx_buffers[buff_n].skb);
- ksp->rx_buffers[buff_n].skb = NULL;
- }
- }
-}
-
-
-/**
- * ks8695_setup_irq - IRQ setup helper function
- * @irq: The IRQ number to claim
- * @irq_name: The name to give the IRQ claimant
- * @handler: The function to call to handle the IRQ
- * @ndev: The net_device to pass in as the dev_id argument to the handler
- *
- * Return 0 on success.
- */
-static int
-ks8695_setup_irq(int irq, const char *irq_name,
- irq_handler_t handler, struct net_device *ndev)
-{
- int ret;
-
- ret = request_irq(irq, handler, IRQF_SHARED, irq_name, ndev);
-
- if (ret) {
- dev_err(&ndev->dev, "failure to request IRQ %d\n", irq);
- return ret;
- }
-
- return 0;
-}
-
-/**
- * ks8695_init_net - Initialise a KS8695 ethernet interface
- * @ksp: The interface to initialise
- *
- * This routine fills the RX ring, initialises the DMA engines,
- * allocates the IRQs and then starts the packet TX and RX
- * engines.
- */
-static int
-ks8695_init_net(struct ks8695_priv *ksp)
-{
- int ret;
- u32 ctrl;
-
- ks8695_refill_rxbuffers(ksp);
-
- /* Initialise the DMA engines */
- ks8695_writereg(ksp, KS8695_RDLB, (u32) ksp->rx_ring_dma);
- ks8695_writereg(ksp, KS8695_TDLB, (u32) ksp->tx_ring_dma);
-
- /* Request the IRQs */
- ret = ks8695_setup_irq(ksp->rx_irq, ksp->rx_irq_name,
- ks8695_rx_irq, ksp->ndev);
- if (ret)
- return ret;
- ret = ks8695_setup_irq(ksp->tx_irq, ksp->tx_irq_name,
- ks8695_tx_irq, ksp->ndev);
- if (ret)
- return ret;
- if (ksp->link_irq != -1) {
- ret = ks8695_setup_irq(ksp->link_irq, ksp->link_irq_name,
- ks8695_link_irq, ksp->ndev);
- if (ret)
- return ret;
- }
-
- /* Set up the ring indices */
- ksp->next_rx_desc_read = 0;
- ksp->tx_ring_next_slot = 0;
- ksp->tx_ring_used = 0;
-
- /* Bring up transmission */
- ctrl = ks8695_readreg(ksp, KS8695_DTXC);
- /* Enable packet transmission */
- ks8695_writereg(ksp, KS8695_DTXC, ctrl | DTXC_TE);
-
- /* Bring up the reception */
- ctrl = ks8695_readreg(ksp, KS8695_DRXC);
- /* Enable packet reception */
- ks8695_writereg(ksp, KS8695_DRXC, ctrl | DRXC_RE);
- /* And start the DMA engine */
- ks8695_writereg(ksp, KS8695_DRSC, 0);
-
- /* All done */
- return 0;
-}
-
-/**
- * ks8695_release_device - HW resource release for KS8695 e-net
- * @ksp: The device to be freed
- *
- * This unallocates io memory regions, dma-coherent regions etc
- * which were allocated in ks8695_probe.
- */
-static void
-ks8695_release_device(struct ks8695_priv *ksp)
-{
- /* Unmap the registers */
- iounmap(ksp->io_regs);
- if (ksp->phyiface_regs)
- iounmap(ksp->phyiface_regs);
-
- /* And release the request */
- release_resource(ksp->regs_req);
- kfree(ksp->regs_req);
- if (ksp->phyiface_req) {
- release_resource(ksp->phyiface_req);
- kfree(ksp->phyiface_req);
- }
-
- /* Free the ring buffers */
- dma_free_coherent(ksp->dev, RING_DMA_SIZE,
- ksp->ring_base, ksp->ring_base_dma);
-}
-
-/* Ethtool support */
-
-/**
- * ks8695_get_msglevel - Get the messages enabled for emission
- * @ndev: The network device to read from
- */
-static u32
-ks8695_get_msglevel(struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- return ksp->msg_enable;
-}
-
-/**
- * ks8695_set_msglevel - Set the messages enabled for emission
- * @ndev: The network device to configure
- * @value: The messages to set for emission
- */
-static void
-ks8695_set_msglevel(struct net_device *ndev, u32 value)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- ksp->msg_enable = value;
-}
-
-/**
- * ks8695_wan_get_settings - Get device-specific settings.
- * @ndev: The network device to read settings from
- * @cmd: The ethtool structure to read into
- */
-static int
-ks8695_wan_get_settings(struct net_device *ndev, struct ethtool_cmd *cmd)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- u32 ctrl;
-
- /* All ports on the KS8695 support these... */
- cmd->supported = (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
- SUPPORTED_TP | SUPPORTED_MII);
- cmd->transceiver = XCVR_INTERNAL;
-
- cmd->advertising = ADVERTISED_TP | ADVERTISED_MII;
- cmd->port = PORT_MII;
- cmd->supported |= (SUPPORTED_Autoneg | SUPPORTED_Pause);
- cmd->phy_address = 0;
-
- ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
- if ((ctrl & WMC_WAND) == 0) {
- /* auto-negotiation is enabled */
- cmd->advertising |= ADVERTISED_Autoneg;
- if (ctrl & WMC_WANA100F)
- cmd->advertising |= ADVERTISED_100baseT_Full;
- if (ctrl & WMC_WANA100H)
- cmd->advertising |= ADVERTISED_100baseT_Half;
- if (ctrl & WMC_WANA10F)
- cmd->advertising |= ADVERTISED_10baseT_Full;
- if (ctrl & WMC_WANA10H)
- cmd->advertising |= ADVERTISED_10baseT_Half;
- if (ctrl & WMC_WANAP)
- cmd->advertising |= ADVERTISED_Pause;
- cmd->autoneg = AUTONEG_ENABLE;
-
- ethtool_cmd_speed_set(cmd,
- (ctrl & WMC_WSS) ? SPEED_100 : SPEED_10);
- cmd->duplex = (ctrl & WMC_WDS) ?
- DUPLEX_FULL : DUPLEX_HALF;
- } else {
- /* auto-negotiation is disabled */
- cmd->autoneg = AUTONEG_DISABLE;
-
- ethtool_cmd_speed_set(cmd, ((ctrl & WMC_WANF100) ?
- SPEED_100 : SPEED_10));
- cmd->duplex = (ctrl & WMC_WANFF) ?
- DUPLEX_FULL : DUPLEX_HALF;
- }
-
- return 0;
-}
-
-/**
- * ks8695_wan_set_settings - Set device-specific settings.
- * @ndev: The network device to configure
- * @cmd: The settings to configure
- */
-static int
-ks8695_wan_set_settings(struct net_device *ndev, struct ethtool_cmd *cmd)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- u32 ctrl;
-
- if ((cmd->speed != SPEED_10) && (cmd->speed != SPEED_100))
- return -EINVAL;
- if ((cmd->duplex != DUPLEX_HALF) && (cmd->duplex != DUPLEX_FULL))
- return -EINVAL;
- if (cmd->port != PORT_MII)
- return -EINVAL;
- if (cmd->transceiver != XCVR_INTERNAL)
- return -EINVAL;
- if ((cmd->autoneg != AUTONEG_DISABLE) &&
- (cmd->autoneg != AUTONEG_ENABLE))
- return -EINVAL;
-
- if (cmd->autoneg == AUTONEG_ENABLE) {
- if ((cmd->advertising & (ADVERTISED_10baseT_Half |
- ADVERTISED_10baseT_Full |
- ADVERTISED_100baseT_Half |
- ADVERTISED_100baseT_Full)) == 0)
- return -EINVAL;
-
- ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
-
- ctrl &= ~(WMC_WAND | WMC_WANA100F | WMC_WANA100H |
- WMC_WANA10F | WMC_WANA10H);
- if (cmd->advertising & ADVERTISED_100baseT_Full)
- ctrl |= WMC_WANA100F;
- if (cmd->advertising & ADVERTISED_100baseT_Half)
- ctrl |= WMC_WANA100H;
- if (cmd->advertising & ADVERTISED_10baseT_Full)
- ctrl |= WMC_WANA10F;
- if (cmd->advertising & ADVERTISED_10baseT_Half)
- ctrl |= WMC_WANA10H;
-
- /* force a re-negotiation */
- ctrl |= WMC_WANR;
- writel(ctrl, ksp->phyiface_regs + KS8695_WMC);
- } else {
- ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
-
- /* disable auto-negotiation */
- ctrl |= WMC_WAND;
- ctrl &= ~(WMC_WANF100 | WMC_WANFF);
-
- if (cmd->speed == SPEED_100)
- ctrl |= WMC_WANF100;
- if (cmd->duplex == DUPLEX_FULL)
- ctrl |= WMC_WANFF;
-
- writel(ctrl, ksp->phyiface_regs + KS8695_WMC);
- }
-
- return 0;
-}
-
-/**
- * ks8695_wan_nwayreset - Restart the autonegotiation on the port.
- * @ndev: The network device to restart autoneotiation on
- */
-static int
-ks8695_wan_nwayreset(struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- u32 ctrl;
-
- ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
-
- if ((ctrl & WMC_WAND) == 0)
- writel(ctrl | WMC_WANR,
- ksp->phyiface_regs + KS8695_WMC);
- else
- /* auto-negotiation not enabled */
- return -EINVAL;
-
- return 0;
-}
-
-/**
- * ks8695_wan_get_pause - Retrieve network pause/flow-control advertising
- * @ndev: The device to retrieve settings from
- * @param: The structure to fill out with the information
- */
-static void
-ks8695_wan_get_pause(struct net_device *ndev, struct ethtool_pauseparam *param)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- u32 ctrl;
-
- ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
-
- /* advertise Pause */
- param->autoneg = (ctrl & WMC_WANAP);
-
- /* current Rx Flow-control */
- ctrl = ks8695_readreg(ksp, KS8695_DRXC);
- param->rx_pause = (ctrl & DRXC_RFCE);
-
- /* current Tx Flow-control */
- ctrl = ks8695_readreg(ksp, KS8695_DTXC);
- param->tx_pause = (ctrl & DTXC_TFCE);
-}
-
-/**
- * ks8695_get_drvinfo - Retrieve driver information
- * @ndev: The network device to retrieve info about
- * @info: The info structure to fill out.
- */
-static void
-ks8695_get_drvinfo(struct net_device *ndev, struct ethtool_drvinfo *info)
-{
- strlcpy(info->driver, MODULENAME, sizeof(info->driver));
- strlcpy(info->version, MODULEVERSION, sizeof(info->version));
- strlcpy(info->bus_info, dev_name(ndev->dev.parent),
- sizeof(info->bus_info));
-}
-
-static const struct ethtool_ops ks8695_ethtool_ops = {
- .get_msglevel = ks8695_get_msglevel,
- .set_msglevel = ks8695_set_msglevel,
- .get_drvinfo = ks8695_get_drvinfo,
-};
-
-static const struct ethtool_ops ks8695_wan_ethtool_ops = {
- .get_msglevel = ks8695_get_msglevel,
- .set_msglevel = ks8695_set_msglevel,
- .get_settings = ks8695_wan_get_settings,
- .set_settings = ks8695_wan_set_settings,
- .nway_reset = ks8695_wan_nwayreset,
- .get_link = ethtool_op_get_link,
- .get_pauseparam = ks8695_wan_get_pause,
- .get_drvinfo = ks8695_get_drvinfo,
-};
-
-/* Network device interface functions */
-
-/**
- * ks8695_set_mac - Update MAC in net dev and HW
- * @ndev: The network device to update
- * @addr: The new MAC address to set
- */
-static int
-ks8695_set_mac(struct net_device *ndev, void *addr)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- struct sockaddr *address = addr;
-
- if (!is_valid_ether_addr(address->sa_data))
- return -EADDRNOTAVAIL;
-
- memcpy(ndev->dev_addr, address->sa_data, ndev->addr_len);
-
- ks8695_update_mac(ksp);
-
- dev_dbg(ksp->dev, "%s: Updated MAC address to %pM\n",
- ndev->name, ndev->dev_addr);
-
- return 0;
-}
-
-/**
- * ks8695_set_multicast - Set up the multicast behaviour of the interface
- * @ndev: The net_device to configure
- *
- * This routine, called by the net layer, configures promiscuity
- * and multicast reception behaviour for the interface.
- */
-static void
-ks8695_set_multicast(struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- u32 ctrl;
-
- ctrl = ks8695_readreg(ksp, KS8695_DRXC);
-
- if (ndev->flags & IFF_PROMISC) {
- /* enable promiscuous mode */
- ctrl |= DRXC_RA;
- } else if (ndev->flags & ~IFF_PROMISC) {
- /* disable promiscuous mode */
- ctrl &= ~DRXC_RA;
- }
-
- if (ndev->flags & IFF_ALLMULTI) {
- /* enable all multicast mode */
- ctrl |= DRXC_RM;
- } else if (netdev_mc_count(ndev) > KS8695_NR_ADDRESSES) {
- /* more specific multicast addresses than can be
- * handled in hardware
- */
- ctrl |= DRXC_RM;
- } else {
- /* enable specific multicasts */
- ctrl &= ~DRXC_RM;
- ks8695_init_partial_multicast(ksp, ndev);
- }
-
- ks8695_writereg(ksp, KS8695_DRXC, ctrl);
-}
-
-/**
- * ks8695_timeout - Handle a network tx/rx timeout.
- * @ndev: The net_device which timed out.
- *
- * A network transaction timed out, reset the device.
- */
-static void
-ks8695_timeout(struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- netif_stop_queue(ndev);
- ks8695_shutdown(ksp);
-
- ks8695_reset(ksp);
-
- ks8695_update_mac(ksp);
-
- /* We ignore the return from this since it managed to init
- * before it probably will be okay to init again.
- */
- ks8695_init_net(ksp);
-
- /* Reconfigure promiscuity etc */
- ks8695_set_multicast(ndev);
-
- /* And start the TX queue once more */
- netif_start_queue(ndev);
-}
-
-/**
- * ks8695_start_xmit - Start a packet transmission
- * @skb: The packet to transmit
- * @ndev: The network device to send the packet on
- *
- * This routine, called by the net layer, takes ownership of the
- * sk_buff and adds it to the TX ring. It then kicks the TX DMA
- * engine to ensure transmission begins.
- */
-static int
-ks8695_start_xmit(struct sk_buff *skb, struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- int buff_n;
- dma_addr_t dmap;
-
- spin_lock_irq(&ksp->txq_lock);
-
- if (ksp->tx_ring_used == MAX_TX_DESC) {
- /* Somehow we got entered when we have no room */
- spin_unlock_irq(&ksp->txq_lock);
- return NETDEV_TX_BUSY;
- }
-
- buff_n = ksp->tx_ring_next_slot;
-
- BUG_ON(ksp->tx_buffers[buff_n].skb);
-
- dmap = dma_map_single(ksp->dev, skb->data, skb->len, DMA_TO_DEVICE);
- if (unlikely(dma_mapping_error(ksp->dev, dmap))) {
- /* Failed to DMA map this SKB, give it back for now */
- spin_unlock_irq(&ksp->txq_lock);
- dev_dbg(ksp->dev, "%s: Could not map DMA memory for "\
- "transmission, trying later\n", ndev->name);
- return NETDEV_TX_BUSY;
- }
-
- ksp->tx_buffers[buff_n].dma_ptr = dmap;
- /* Mapped okay, store the buffer pointer and length for later */
- ksp->tx_buffers[buff_n].skb = skb;
- ksp->tx_buffers[buff_n].length = skb->len;
-
- /* Fill out the TX descriptor */
- ksp->tx_ring[buff_n].data_ptr =
- cpu_to_le32(ksp->tx_buffers[buff_n].dma_ptr);
- ksp->tx_ring[buff_n].status =
- cpu_to_le32(TDES_IC | TDES_FS | TDES_LS |
- (skb->len & TDES_TBS));
-
- wmb();
-
- /* Hand it over to the hardware */
- ksp->tx_ring[buff_n].owner = cpu_to_le32(TDES_OWN);
-
- if (++ksp->tx_ring_used == MAX_TX_DESC)
- netif_stop_queue(ndev);
-
- /* Kick the TX DMA in case it decided to go IDLE */
- ks8695_writereg(ksp, KS8695_DTSC, 0);
-
- /* And update the next ring slot */
- ksp->tx_ring_next_slot = (buff_n + 1) & MAX_TX_DESC_MASK;
-
- spin_unlock_irq(&ksp->txq_lock);
- return NETDEV_TX_OK;
-}
-
-/**
- * ks8695_stop - Stop (shutdown) a KS8695 ethernet interface
- * @ndev: The net_device to stop
- *
- * This disables the TX queue and cleans up a KS8695 ethernet
- * device.
- */
-static int
-ks8695_stop(struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- netif_stop_queue(ndev);
- napi_disable(&ksp->napi);
-
- ks8695_shutdown(ksp);
-
- return 0;
-}
-
-/**
- * ks8695_open - Open (bring up) a KS8695 ethernet interface
- * @ndev: The net_device to open
- *
- * This resets, configures the MAC, initialises the RX ring and
- * DMA engines and starts the TX queue for a KS8695 ethernet
- * device.
- */
-static int
-ks8695_open(struct net_device *ndev)
-{
- struct ks8695_priv *ksp = netdev_priv(ndev);
- int ret;
-
- if (!is_valid_ether_addr(ndev->dev_addr))
- return -EADDRNOTAVAIL;
-
- ks8695_reset(ksp);
-
- ks8695_update_mac(ksp);
-
- ret = ks8695_init_net(ksp);
- if (ret) {
- ks8695_shutdown(ksp);
- return ret;
- }
-
- napi_enable(&ksp->napi);
- netif_start_queue(ndev);
-
- return 0;
-}
-
-/* Platform device driver */
-
-/**
- * ks8695_init_switch - Init LAN switch to known good defaults.
- * @ksp: The device to initialise
- *
- * This initialises the LAN switch in the KS8695 to a known-good
- * set of defaults.
- */
-static void __devinit
-ks8695_init_switch(struct ks8695_priv *ksp)
-{
- u32 ctrl;
-
- /* Default value for SEC0 according to datasheet */
- ctrl = 0x40819e00;
-
- /* LED0 = Speed LED1 = Link/Activity */
- ctrl &= ~(SEC0_LLED1S | SEC0_LLED0S);
- ctrl |= (LLED0S_LINK | LLED1S_LINK_ACTIVITY);
-
- /* Enable Switch */
- ctrl |= SEC0_ENABLE;
-
- writel(ctrl, ksp->phyiface_regs + KS8695_SEC0);
-
- /* Defaults for SEC1 */
- writel(0x9400100, ksp->phyiface_regs + KS8695_SEC1);
-}
-
-/**
- * ks8695_init_wan_phy - Initialise the WAN PHY to sensible defaults
- * @ksp: The device to initialise
- *
- * This initialises a KS8695's WAN phy to sensible values for
- * autonegotiation etc.
- */
-static void __devinit
-ks8695_init_wan_phy(struct ks8695_priv *ksp)
-{
- u32 ctrl;
-
- /* Support auto-negotiation */
- ctrl = (WMC_WANAP | WMC_WANA100F | WMC_WANA100H |
- WMC_WANA10F | WMC_WANA10H);
-
- /* LED0 = Activity , LED1 = Link */
- ctrl |= (WLED0S_ACTIVITY | WLED1S_LINK);
-
- /* Restart Auto-negotiation */
- ctrl |= WMC_WANR;
-
- writel(ctrl, ksp->phyiface_regs + KS8695_WMC);
-
- writel(0, ksp->phyiface_regs + KS8695_WPPM);
- writel(0, ksp->phyiface_regs + KS8695_PPS);
-}
-
-static const struct net_device_ops ks8695_netdev_ops = {
- .ndo_open = ks8695_open,
- .ndo_stop = ks8695_stop,
- .ndo_start_xmit = ks8695_start_xmit,
- .ndo_tx_timeout = ks8695_timeout,
- .ndo_set_mac_address = ks8695_set_mac,
- .ndo_validate_addr = eth_validate_addr,
- .ndo_set_multicast_list = ks8695_set_multicast,
-};
-
-/**
- * ks8695_probe - Probe and initialise a KS8695 ethernet interface
- * @pdev: The platform device to probe
- *
- * Initialise a KS8695 ethernet device from platform data.
- *
- * This driver requires at least one IORESOURCE_MEM for the
- * registers and two IORESOURCE_IRQ for the RX and TX IRQs
- * respectively. It can optionally take an additional
- * IORESOURCE_MEM for the switch or phy in the case of the lan or
- * wan ports, and an IORESOURCE_IRQ for the link IRQ for the wan
- * port.
- */
-static int __devinit
-ks8695_probe(struct platform_device *pdev)
-{
- struct ks8695_priv *ksp;
- struct net_device *ndev;
- struct resource *regs_res, *phyiface_res;
- struct resource *rxirq_res, *txirq_res, *linkirq_res;
- int ret = 0;
- int buff_n;
- u32 machigh, maclow;
-
- /* Initialise a net_device */
- ndev = alloc_etherdev(sizeof(struct ks8695_priv));
- if (!ndev) {
- dev_err(&pdev->dev, "could not allocate device.\n");
- return -ENOMEM;
- }
-
- SET_NETDEV_DEV(ndev, &pdev->dev);
-
- dev_dbg(&pdev->dev, "ks8695_probe() called\n");
-
- /* Configure our private structure a little */
- ksp = netdev_priv(ndev);
-
- ksp->dev = &pdev->dev;
- ksp->ndev = ndev;
- ksp->msg_enable = NETIF_MSG_LINK;
-
- /* Retrieve resources */
- regs_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- phyiface_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-
- rxirq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
- txirq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 1);
- linkirq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 2);
-
- if (!(regs_res && rxirq_res && txirq_res)) {
- dev_err(ksp->dev, "insufficient resources\n");
- ret = -ENOENT;
- goto failure;
- }
-
- ksp->regs_req = request_mem_region(regs_res->start,
- resource_size(regs_res),
- pdev->name);
-
- if (!ksp->regs_req) {
- dev_err(ksp->dev, "cannot claim register space\n");
- ret = -EIO;
- goto failure;
- }
-
- ksp->io_regs = ioremap(regs_res->start, resource_size(regs_res));
-
- if (!ksp->io_regs) {
- dev_err(ksp->dev, "failed to ioremap registers\n");
- ret = -EINVAL;
- goto failure;
- }
-
- if (phyiface_res) {
- ksp->phyiface_req =
- request_mem_region(phyiface_res->start,
- resource_size(phyiface_res),
- phyiface_res->name);
-
- if (!ksp->phyiface_req) {
- dev_err(ksp->dev,
- "cannot claim switch register space\n");
- ret = -EIO;
- goto failure;
- }
-
- ksp->phyiface_regs = ioremap(phyiface_res->start,
- resource_size(phyiface_res));
-
- if (!ksp->phyiface_regs) {
- dev_err(ksp->dev,
- "failed to ioremap switch registers\n");
- ret = -EINVAL;
- goto failure;
- }
- }
-
- ksp->rx_irq = rxirq_res->start;
- ksp->rx_irq_name = rxirq_res->name ? rxirq_res->name : "Ethernet RX";
- ksp->tx_irq = txirq_res->start;
- ksp->tx_irq_name = txirq_res->name ? txirq_res->name : "Ethernet TX";
- ksp->link_irq = (linkirq_res ? linkirq_res->start : -1);
- ksp->link_irq_name = (linkirq_res && linkirq_res->name) ?
- linkirq_res->name : "Ethernet Link";
-
- /* driver system setup */
- ndev->netdev_ops = &ks8695_netdev_ops;
- ndev->watchdog_timeo = msecs_to_jiffies(watchdog);
-
- netif_napi_add(ndev, &ksp->napi, ks8695_poll, NAPI_WEIGHT);
-
- /* Retrieve the default MAC addr from the chip. */
- /* The bootloader should have left it in there for us. */
-
- machigh = ks8695_readreg(ksp, KS8695_MAH);
- maclow = ks8695_readreg(ksp, KS8695_MAL);
-
- ndev->dev_addr[0] = (machigh >> 8) & 0xFF;
- ndev->dev_addr[1] = machigh & 0xFF;
- ndev->dev_addr[2] = (maclow >> 24) & 0xFF;
- ndev->dev_addr[3] = (maclow >> 16) & 0xFF;
- ndev->dev_addr[4] = (maclow >> 8) & 0xFF;
- ndev->dev_addr[5] = maclow & 0xFF;
-
- if (!is_valid_ether_addr(ndev->dev_addr))
- dev_warn(ksp->dev, "%s: Invalid ethernet MAC address. Please "
- "set using ifconfig\n", ndev->name);
-
- /* In order to be efficient memory-wise, we allocate both
- * rings in one go.
- */
- ksp->ring_base = dma_alloc_coherent(&pdev->dev, RING_DMA_SIZE,
- &ksp->ring_base_dma, GFP_KERNEL);
- if (!ksp->ring_base) {
- ret = -ENOMEM;
- goto failure;
- }
-
- /* Specify the TX DMA ring buffer */
- ksp->tx_ring = ksp->ring_base;
- ksp->tx_ring_dma = ksp->ring_base_dma;
-
- /* And initialise the queue's lock */
- spin_lock_init(&ksp->txq_lock);
- spin_lock_init(&ksp->rx_lock);
-
- /* Specify the RX DMA ring buffer */
- ksp->rx_ring = ksp->ring_base + TX_RING_DMA_SIZE;
- ksp->rx_ring_dma = ksp->ring_base_dma + TX_RING_DMA_SIZE;
-
- /* Zero the descriptor rings */
- memset(ksp->tx_ring, 0, TX_RING_DMA_SIZE);
- memset(ksp->rx_ring, 0, RX_RING_DMA_SIZE);
-
- /* Build the rings */
- for (buff_n = 0; buff_n < MAX_TX_DESC; ++buff_n) {
- ksp->tx_ring[buff_n].next_desc =
- cpu_to_le32(ksp->tx_ring_dma +
- (sizeof(struct tx_ring_desc) *
- ((buff_n + 1) & MAX_TX_DESC_MASK)));
- }
-
- for (buff_n = 0; buff_n < MAX_RX_DESC; ++buff_n) {
- ksp->rx_ring[buff_n].next_desc =
- cpu_to_le32(ksp->rx_ring_dma +
- (sizeof(struct rx_ring_desc) *
- ((buff_n + 1) & MAX_RX_DESC_MASK)));
- }
-
- /* Initialise the port (physically) */
- if (ksp->phyiface_regs && ksp->link_irq == -1) {
- ks8695_init_switch(ksp);
- ksp->dtype = KS8695_DTYPE_LAN;
- SET_ETHTOOL_OPS(ndev, &ks8695_ethtool_ops);
- } else if (ksp->phyiface_regs && ksp->link_irq != -1) {
- ks8695_init_wan_phy(ksp);
- ksp->dtype = KS8695_DTYPE_WAN;
- SET_ETHTOOL_OPS(ndev, &ks8695_wan_ethtool_ops);
- } else {
- /* No initialisation since HPNA does not have a PHY */
- ksp->dtype = KS8695_DTYPE_HPNA;
- SET_ETHTOOL_OPS(ndev, &ks8695_ethtool_ops);
- }
-
- /* And bring up the net_device with the net core */
- platform_set_drvdata(pdev, ndev);
- ret = register_netdev(ndev);
-
- if (ret == 0) {
- dev_info(ksp->dev, "ks8695 ethernet (%s) MAC: %pM\n",
- ks8695_port_type(ksp), ndev->dev_addr);
- } else {
- /* Report the failure to register the net_device */
- dev_err(ksp->dev, "ks8695net: failed to register netdev.\n");
- goto failure;
- }
-
- /* All is well */
- return 0;
-
- /* Error exit path */
-failure:
- ks8695_release_device(ksp);
- free_netdev(ndev);
-
- return ret;
-}
-
-/**
- * ks8695_drv_suspend - Suspend a KS8695 ethernet platform device.
- * @pdev: The device to suspend
- * @state: The suspend state
- *
- * This routine detaches and shuts down a KS8695 ethernet device.
- */
-static int
-ks8695_drv_suspend(struct platform_device *pdev, pm_message_t state)
-{
- struct net_device *ndev = platform_get_drvdata(pdev);
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- ksp->in_suspend = 1;
-
- if (netif_running(ndev)) {
- netif_device_detach(ndev);
- ks8695_shutdown(ksp);
- }
-
- return 0;
-}
-
-/**
- * ks8695_drv_resume - Resume a KS8695 ethernet platform device.
- * @pdev: The device to resume
- *
- * This routine re-initialises and re-attaches a KS8695 ethernet
- * device.
- */
-static int
-ks8695_drv_resume(struct platform_device *pdev)
-{
- struct net_device *ndev = platform_get_drvdata(pdev);
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- if (netif_running(ndev)) {
- ks8695_reset(ksp);
- ks8695_init_net(ksp);
- ks8695_set_multicast(ndev);
- netif_device_attach(ndev);
- }
-
- ksp->in_suspend = 0;
-
- return 0;
-}
-
-/**
- * ks8695_drv_remove - Remove a KS8695 net device on driver unload.
- * @pdev: The platform device to remove
- *
- * This unregisters and releases a KS8695 ethernet device.
- */
-static int __devexit
-ks8695_drv_remove(struct platform_device *pdev)
-{
- struct net_device *ndev = platform_get_drvdata(pdev);
- struct ks8695_priv *ksp = netdev_priv(ndev);
-
- platform_set_drvdata(pdev, NULL);
- netif_napi_del(&ksp->napi);
-
- unregister_netdev(ndev);
- ks8695_release_device(ksp);
- free_netdev(ndev);
-
- dev_dbg(&pdev->dev, "released and freed device\n");
- return 0;
-}
-
-static struct platform_driver ks8695_driver = {
- .driver = {
- .name = MODULENAME,
- .owner = THIS_MODULE,
- },
- .probe = ks8695_probe,
- .remove = __devexit_p(ks8695_drv_remove),
- .suspend = ks8695_drv_suspend,
- .resume = ks8695_drv_resume,
-};
-
-/* Module interface */
-
-static int __init
-ks8695_init(void)
-{
- printk(KERN_INFO "%s Ethernet driver, V%s\n",
- MODULENAME, MODULEVERSION);
-
- return platform_driver_register(&ks8695_driver);
-}
-
-static void __exit
-ks8695_cleanup(void)
-{
- platform_driver_unregister(&ks8695_driver);
-}
-
-module_init(ks8695_init);
-module_exit(ks8695_cleanup);
-
-MODULE_AUTHOR("Simtec Electronics");
-MODULE_DESCRIPTION("Micrel KS8695 (Centaur) Ethernet driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:" MODULENAME);
-
-module_param(watchdog, int, 0400);
-MODULE_PARM_DESC(watchdog, "transmit timeout in milliseconds");
+++ /dev/null
-/*
- * Micrel KS8695 (Centaur) Ethernet.
- *
- * Copyright 2008 Simtec Electronics
- * Daniel Silverstone <dsilvers@simtec.co.uk>
- * Vincent Sanders <vince@simtec.co.uk>
- */
-
-#ifndef KS8695NET_H
-#define KS8695NET_H
-
-/* Receive descriptor flags */
-#define RDES_OWN (1 << 31) /* Ownership */
-#define RDES_FS (1 << 30) /* First Descriptor */
-#define RDES_LS (1 << 29) /* Last Descriptor */
-#define RDES_IPE (1 << 28) /* IP Checksum error */
-#define RDES_TCPE (1 << 27) /* TCP Checksum error */
-#define RDES_UDPE (1 << 26) /* UDP Checksum error */
-#define RDES_ES (1 << 25) /* Error summary */
-#define RDES_MF (1 << 24) /* Multicast Frame */
-#define RDES_RE (1 << 19) /* MII Error reported */
-#define RDES_TL (1 << 18) /* Frame too Long */
-#define RDES_RF (1 << 17) /* Runt Frame */
-#define RDES_CE (1 << 16) /* CRC error */
-#define RDES_FT (1 << 15) /* Frame Type */
-#define RDES_FLEN (0x7ff) /* Frame Length */
-
-#define RDES_RER (1 << 25) /* Receive End of Ring */
-#define RDES_RBS (0x7ff) /* Receive Buffer Size */
-
-/* Transmit descriptor flags */
-
-#define TDES_OWN (1 << 31) /* Ownership */
-
-#define TDES_IC (1 << 31) /* Interrupt on Completion */
-#define TDES_FS (1 << 30) /* First Segment */
-#define TDES_LS (1 << 29) /* Last Segment */
-#define TDES_IPCKG (1 << 28) /* IP Checksum generate */
-#define TDES_TCPCKG (1 << 27) /* TCP Checksum generate */
-#define TDES_UDPCKG (1 << 26) /* UDP Checksum generate */
-#define TDES_TER (1 << 25) /* Transmit End of Ring */
-#define TDES_TBS (0x7ff) /* Transmit Buffer Size */
-
-/*
- * Network controller register offsets
- */
-#define KS8695_DTXC (0x00) /* DMA Transmit Control */
-#define KS8695_DRXC (0x04) /* DMA Receive Control */
-#define KS8695_DTSC (0x08) /* DMA Transmit Start Command */
-#define KS8695_DRSC (0x0c) /* DMA Receive Start Command */
-#define KS8695_TDLB (0x10) /* Transmit Descriptor List
- * Base Address
- */
-#define KS8695_RDLB (0x14) /* Receive Descriptor List
- * Base Address
- */
-#define KS8695_MAL (0x18) /* MAC Station Address Low */
-#define KS8695_MAH (0x1c) /* MAC Station Address High */
-#define KS8695_AAL_(n) (0x80 + ((n)*8)) /* MAC Additional
- * Station Address
- * (0..15) Low
- */
-#define KS8695_AAH_(n) (0x84 + ((n)*8)) /* MAC Additional
- * Station Address
- * (0..15) High
- */
-
-
-/* DMA Transmit Control Register */
-#define DTXC_TRST (1 << 31) /* Soft Reset */
-#define DTXC_TBS (0x3f << 24) /* Transmit Burst Size */
-#define DTXC_TUCG (1 << 18) /* Transmit UDP
- * Checksum Generate
- */
-#define DTXC_TTCG (1 << 17) /* Transmit TCP
- * Checksum Generate
- */
-#define DTXC_TICG (1 << 16) /* Transmit IP
- * Checksum Generate
- */
-#define DTXC_TFCE (1 << 9) /* Transmit Flow
- * Control Enable
- */
-#define DTXC_TLB (1 << 8) /* Loopback mode */
-#define DTXC_TEP (1 << 2) /* Transmit Enable Padding */
-#define DTXC_TAC (1 << 1) /* Transmit Add CRC */
-#define DTXC_TE (1 << 0) /* TX Enable */
-
-/* DMA Receive Control Register */
-#define DRXC_RBS (0x3f << 24) /* Receive Burst Size */
-#define DRXC_RUCC (1 << 18) /* Receive UDP Checksum check */
-#define DRXC_RTCG (1 << 17) /* Receive TCP Checksum check */
-#define DRXC_RICG (1 << 16) /* Receive IP Checksum check */
-#define DRXC_RFCE (1 << 9) /* Receive Flow Control
- * Enable
- */
-#define DRXC_RB (1 << 6) /* Receive Broadcast */
-#define DRXC_RM (1 << 5) /* Receive Multicast */
-#define DRXC_RU (1 << 4) /* Receive Unicast */
-#define DRXC_RERR (1 << 3) /* Receive Error Frame */
-#define DRXC_RA (1 << 2) /* Receive All */
-#define DRXC_RE (1 << 0) /* RX Enable */
-
-/* Additional Station Address High */
-#define AAH_E (1 << 31) /* Address Enabled */
-
-#endif /* KS8695NET_H */
source "drivers/net/ethernet/xscale/Kconfig"
source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
+source "drivers/net/ethernet/micrel/Kconfig"
source "drivers/net/ethernet/myricom/Kconfig"
source "drivers/net/ethernet/natsemi/Kconfig"
source "drivers/net/ethernet/8390/Kconfig"
obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
+obj-$(CONFIG_NET_VENDOR_MICREL) += micrel/
obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/
obj-$(CONFIG_NET_VENDOR_OKI) += oki-semi/
--- /dev/null
+#
+# Micrel device configuration
+#
+
+config NET_VENDOR_MICREL
+ bool "Micrel devices"
+ depends on (HAS_IOMEM && DMA_ENGINE) || SPI || PCI || HAS_IOMEM || \
+ (ARM && ARCH_KS8695)
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Micrel devices. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_MICREL
+
+config ARM_KS8695_ETHER
+ tristate "KS8695 Ethernet support"
+ depends on ARM && ARCH_KS8695
+ select MII
+ ---help---
+ If you wish to compile a kernel for the KS8695 and want to
+ use the internal ethernet then you should answer Y to this.
+
+config KS8842
+ tristate "Micrel KSZ8841/42 with generic bus interface"
+ depends on HAS_IOMEM && DMA_ENGINE
+ ---help---
+ This platform driver is for KSZ8841(1-port) / KS8842(2-port)
+ ethernet switch chip (managed, VLAN, QoS) from Micrel or
+ Timberdale(FPGA).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ ---help---
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ ---help---
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
+config KSZ884X_PCI
+ tristate "Micrel KSZ8841/2 PCI"
+ depends on PCI
+ select MII
+ select CRC32
+ ---help---
+ This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ksz884x.
+
+endif # NET_VENDOR_MICREL
--- /dev/null
+#
+# Makefile for the Micrel network device drivers.
+#
+
+obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o
+obj-$(CONFIG_KS8842) += ks8842.o
+obj-$(CONFIG_KS8851) += ks8851.o
+obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
+obj-$(CONFIG_KSZ884X_PCI) += ksz884x.o
--- /dev/null
+/*
+ * Micrel KS8695 (Centaur) Ethernet.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * Copyright 2008 Simtec Electronics
+ * Daniel Silverstone <dsilvers@simtec.co.uk>
+ * Vincent Sanders <vince@simtec.co.uk>
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+
+#include <asm/irq.h>
+
+#include <mach/regs-switch.h>
+#include <mach/regs-misc.h>
+#include <asm/mach/irq.h>
+#include <mach/regs-irq.h>
+
+#include "ks8695net.h"
+
+#define MODULENAME "ks8695_ether"
+#define MODULEVERSION "1.02"
+
+/*
+ * Transmit and device reset timeout, default 5 seconds.
+ */
+static int watchdog = 5000;
+
+/* Hardware structures */
+
+/**
+ * struct rx_ring_desc - Receive descriptor ring element
+ * @status: The status of the descriptor element (E.g. who owns it)
+ * @length: The number of bytes in the block pointed to by data_ptr
+ * @data_ptr: The physical address of the data block to receive into
+ * @next_desc: The physical address of the next descriptor element.
+ */
+struct rx_ring_desc {
+ __le32 status;
+ __le32 length;
+ __le32 data_ptr;
+ __le32 next_desc;
+};
+
+/**
+ * struct tx_ring_desc - Transmit descriptor ring element
+ * @owner: Who owns the descriptor
+ * @status: The number of bytes in the block pointed to by data_ptr
+ * @data_ptr: The physical address of the data block to receive into
+ * @next_desc: The physical address of the next descriptor element.
+ */
+struct tx_ring_desc {
+ __le32 owner;
+ __le32 status;
+ __le32 data_ptr;
+ __le32 next_desc;
+};
+
+/**
+ * struct ks8695_skbuff - sk_buff wrapper for rx/tx rings.
+ * @skb: The buffer in the ring
+ * @dma_ptr: The mapped DMA pointer of the buffer
+ * @length: The number of bytes mapped to dma_ptr
+ */
+struct ks8695_skbuff {
+ struct sk_buff *skb;
+ dma_addr_t dma_ptr;
+ u32 length;
+};
+
+/* Private device structure */
+
+#define MAX_TX_DESC 8
+#define MAX_TX_DESC_MASK 0x7
+#define MAX_RX_DESC 16
+#define MAX_RX_DESC_MASK 0xf
+
+/*napi_weight have better more than rx DMA buffers*/
+#define NAPI_WEIGHT 64
+
+#define MAX_RXBUF_SIZE 0x700
+
+#define TX_RING_DMA_SIZE (sizeof(struct tx_ring_desc) * MAX_TX_DESC)
+#define RX_RING_DMA_SIZE (sizeof(struct rx_ring_desc) * MAX_RX_DESC)
+#define RING_DMA_SIZE (TX_RING_DMA_SIZE + RX_RING_DMA_SIZE)
+
+/**
+ * enum ks8695_dtype - Device type
+ * @KS8695_DTYPE_WAN: This device is a WAN interface
+ * @KS8695_DTYPE_LAN: This device is a LAN interface
+ * @KS8695_DTYPE_HPNA: This device is an HPNA interface
+ */
+enum ks8695_dtype {
+ KS8695_DTYPE_WAN,
+ KS8695_DTYPE_LAN,
+ KS8695_DTYPE_HPNA,
+};
+
+/**
+ * struct ks8695_priv - Private data for the KS8695 Ethernet
+ * @in_suspend: Flag to indicate if we're suspending/resuming
+ * @ndev: The net_device for this interface
+ * @dev: The platform device object for this interface
+ * @dtype: The type of this device
+ * @io_regs: The ioremapped registers for this interface
+ * @napi : Add support NAPI for Rx
+ * @rx_irq_name: The textual name of the RX IRQ from the platform data
+ * @tx_irq_name: The textual name of the TX IRQ from the platform data
+ * @link_irq_name: The textual name of the link IRQ from the
+ * platform data if available
+ * @rx_irq: The IRQ number for the RX IRQ
+ * @tx_irq: The IRQ number for the TX IRQ
+ * @link_irq: The IRQ number for the link IRQ if available
+ * @regs_req: The resource request for the registers region
+ * @phyiface_req: The resource request for the phy/switch region
+ * if available
+ * @phyiface_regs: The ioremapped registers for the phy/switch if available
+ * @ring_base: The base pointer of the dma coherent memory for the rings
+ * @ring_base_dma: The DMA mapped equivalent of ring_base
+ * @tx_ring: The pointer in ring_base of the TX ring
+ * @tx_ring_used: The number of slots in the TX ring which are occupied
+ * @tx_ring_next_slot: The next slot to fill in the TX ring
+ * @tx_ring_dma: The DMA mapped equivalent of tx_ring
+ * @tx_buffers: The sk_buff mappings for the TX ring
+ * @txq_lock: A lock to protect the tx_buffers tx_ring_used etc variables
+ * @rx_ring: The pointer in ring_base of the RX ring
+ * @rx_ring_dma: The DMA mapped equivalent of rx_ring
+ * @rx_buffers: The sk_buff mappings for the RX ring
+ * @next_rx_desc_read: The next RX descriptor to read from on IRQ
+ * @rx_lock: A lock to protect Rx irq function
+ * @msg_enable: The flags for which messages to emit
+ */
+struct ks8695_priv {
+ int in_suspend;
+ struct net_device *ndev;
+ struct device *dev;
+ enum ks8695_dtype dtype;
+ void __iomem *io_regs;
+
+ struct napi_struct napi;
+
+ const char *rx_irq_name, *tx_irq_name, *link_irq_name;
+ int rx_irq, tx_irq, link_irq;
+
+ struct resource *regs_req, *phyiface_req;
+ void __iomem *phyiface_regs;
+
+ void *ring_base;
+ dma_addr_t ring_base_dma;
+
+ struct tx_ring_desc *tx_ring;
+ int tx_ring_used;
+ int tx_ring_next_slot;
+ dma_addr_t tx_ring_dma;
+ struct ks8695_skbuff tx_buffers[MAX_TX_DESC];
+ spinlock_t txq_lock;
+
+ struct rx_ring_desc *rx_ring;
+ dma_addr_t rx_ring_dma;
+ struct ks8695_skbuff rx_buffers[MAX_RX_DESC];
+ int next_rx_desc_read;
+ spinlock_t rx_lock;
+
+ int msg_enable;
+};
+
+/* Register access */
+
+/**
+ * ks8695_readreg - Read from a KS8695 ethernet register
+ * @ksp: The device to read from
+ * @reg: The register to read
+ */
+static inline u32
+ks8695_readreg(struct ks8695_priv *ksp, int reg)
+{
+ return readl(ksp->io_regs + reg);
+}
+
+/**
+ * ks8695_writereg - Write to a KS8695 ethernet register
+ * @ksp: The device to write to
+ * @reg: The register to write
+ * @value: The value to write to the register
+ */
+static inline void
+ks8695_writereg(struct ks8695_priv *ksp, int reg, u32 value)
+{
+ writel(value, ksp->io_regs + reg);
+}
+
+/* Utility functions */
+
+/**
+ * ks8695_port_type - Retrieve port-type as user-friendly string
+ * @ksp: The device to return the type for
+ *
+ * Returns a string indicating which of the WAN, LAN or HPNA
+ * ports this device is likely to represent.
+ */
+static const char *
+ks8695_port_type(struct ks8695_priv *ksp)
+{
+ switch (ksp->dtype) {
+ case KS8695_DTYPE_LAN:
+ return "LAN";
+ case KS8695_DTYPE_WAN:
+ return "WAN";
+ case KS8695_DTYPE_HPNA:
+ return "HPNA";
+ }
+
+ return "UNKNOWN";
+}
+
+/**
+ * ks8695_update_mac - Update the MAC registers in the device
+ * @ksp: The device to update
+ *
+ * Updates the MAC registers in the KS8695 device from the address in the
+ * net_device structure associated with this interface.
+ */
+static void
+ks8695_update_mac(struct ks8695_priv *ksp)
+{
+ /* Update the HW with the MAC from the net_device */
+ struct net_device *ndev = ksp->ndev;
+ u32 machigh, maclow;
+
+ maclow = ((ndev->dev_addr[2] << 24) | (ndev->dev_addr[3] << 16) |
+ (ndev->dev_addr[4] << 8) | (ndev->dev_addr[5] << 0));
+ machigh = ((ndev->dev_addr[0] << 8) | (ndev->dev_addr[1] << 0));
+
+ ks8695_writereg(ksp, KS8695_MAL, maclow);
+ ks8695_writereg(ksp, KS8695_MAH, machigh);
+
+}
+
+/**
+ * ks8695_refill_rxbuffers - Re-fill the RX buffer ring
+ * @ksp: The device to refill
+ *
+ * Iterates the RX ring of the device looking for empty slots.
+ * For each empty slot, we allocate and map a new SKB and give it
+ * to the hardware.
+ * This can be called from interrupt context safely.
+ */
+static void
+ks8695_refill_rxbuffers(struct ks8695_priv *ksp)
+{
+ /* Run around the RX ring, filling in any missing sk_buff's */
+ int buff_n;
+
+ for (buff_n = 0; buff_n < MAX_RX_DESC; ++buff_n) {
+ if (!ksp->rx_buffers[buff_n].skb) {
+ struct sk_buff *skb = dev_alloc_skb(MAX_RXBUF_SIZE);
+ dma_addr_t mapping;
+
+ ksp->rx_buffers[buff_n].skb = skb;
+ if (skb == NULL) {
+ /* Failed to allocate one, perhaps
+ * we'll try again later.
+ */
+ break;
+ }
+
+ mapping = dma_map_single(ksp->dev, skb->data,
+ MAX_RXBUF_SIZE,
+ DMA_FROM_DEVICE);
+ if (unlikely(dma_mapping_error(ksp->dev, mapping))) {
+ /* Failed to DMA map this SKB, try later */
+ dev_kfree_skb_irq(skb);
+ ksp->rx_buffers[buff_n].skb = NULL;
+ break;
+ }
+ ksp->rx_buffers[buff_n].dma_ptr = mapping;
+ skb->dev = ksp->ndev;
+ ksp->rx_buffers[buff_n].length = MAX_RXBUF_SIZE;
+
+ /* Record this into the DMA ring */
+ ksp->rx_ring[buff_n].data_ptr = cpu_to_le32(mapping);
+ ksp->rx_ring[buff_n].length =
+ cpu_to_le32(MAX_RXBUF_SIZE);
+
+ wmb();
+
+ /* And give ownership over to the hardware */
+ ksp->rx_ring[buff_n].status = cpu_to_le32(RDES_OWN);
+ }
+ }
+}
+
+/* Maximum number of multicast addresses which the KS8695 HW supports */
+#define KS8695_NR_ADDRESSES 16
+
+/**
+ * ks8695_init_partial_multicast - Init the mcast addr registers
+ * @ksp: The device to initialise
+ * @addr: The multicast address list to use
+ * @nr_addr: The number of addresses in the list
+ *
+ * This routine is a helper for ks8695_set_multicast - it writes
+ * the additional-address registers in the KS8695 ethernet device
+ * and cleans up any others left behind.
+ */
+static void
+ks8695_init_partial_multicast(struct ks8695_priv *ksp,
+ struct net_device *ndev)
+{
+ u32 low, high;
+ int i;
+ struct netdev_hw_addr *ha;
+
+ i = 0;
+ netdev_for_each_mc_addr(ha, ndev) {
+ /* Ran out of space in chip? */
+ BUG_ON(i == KS8695_NR_ADDRESSES);
+
+ low = (ha->addr[2] << 24) | (ha->addr[3] << 16) |
+ (ha->addr[4] << 8) | (ha->addr[5]);
+ high = (ha->addr[0] << 8) | (ha->addr[1]);
+
+ ks8695_writereg(ksp, KS8695_AAL_(i), low);
+ ks8695_writereg(ksp, KS8695_AAH_(i), AAH_E | high);
+ i++;
+ }
+
+ /* Clear the remaining Additional Station Addresses */
+ for (; i < KS8695_NR_ADDRESSES; i++) {
+ ks8695_writereg(ksp, KS8695_AAL_(i), 0);
+ ks8695_writereg(ksp, KS8695_AAH_(i), 0);
+ }
+}
+
+/* Interrupt handling */
+
+/**
+ * ks8695_tx_irq - Transmit IRQ handler
+ * @irq: The IRQ which went off (ignored)
+ * @dev_id: The net_device for the interrupt
+ *
+ * Process the TX ring, clearing out any transmitted slots.
+ * Allows the net_device to pass us new packets once slots are
+ * freed.
+ */
+static irqreturn_t
+ks8695_tx_irq(int irq, void *dev_id)
+{
+ struct net_device *ndev = (struct net_device *)dev_id;
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ int buff_n;
+
+ for (buff_n = 0; buff_n < MAX_TX_DESC; ++buff_n) {
+ if (ksp->tx_buffers[buff_n].skb &&
+ !(ksp->tx_ring[buff_n].owner & cpu_to_le32(TDES_OWN))) {
+ rmb();
+ /* An SKB which is not owned by HW is present */
+ /* Update the stats for the net_device */
+ ndev->stats.tx_packets++;
+ ndev->stats.tx_bytes += ksp->tx_buffers[buff_n].length;
+
+ /* Free the packet from the ring */
+ ksp->tx_ring[buff_n].data_ptr = 0;
+
+ /* Free the sk_buff */
+ dma_unmap_single(ksp->dev,
+ ksp->tx_buffers[buff_n].dma_ptr,
+ ksp->tx_buffers[buff_n].length,
+ DMA_TO_DEVICE);
+ dev_kfree_skb_irq(ksp->tx_buffers[buff_n].skb);
+ ksp->tx_buffers[buff_n].skb = NULL;
+ ksp->tx_ring_used--;
+ }
+ }
+
+ netif_wake_queue(ndev);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * ks8695_get_rx_enable_bit - Get rx interrupt enable/status bit
+ * @ksp: Private data for the KS8695 Ethernet
+ *
+ * For KS8695 document:
+ * Interrupt Enable Register (offset 0xE204)
+ * Bit29 : WAN MAC Receive Interrupt Enable
+ * Bit16 : LAN MAC Receive Interrupt Enable
+ * Interrupt Status Register (Offset 0xF208)
+ * Bit29: WAN MAC Receive Status
+ * Bit16: LAN MAC Receive Status
+ * So, this Rx interrrupt enable/status bit number is equal
+ * as Rx IRQ number.
+ */
+static inline u32 ks8695_get_rx_enable_bit(struct ks8695_priv *ksp)
+{
+ return ksp->rx_irq;
+}
+
+/**
+ * ks8695_rx_irq - Receive IRQ handler
+ * @irq: The IRQ which went off (ignored)
+ * @dev_id: The net_device for the interrupt
+ *
+ * Inform NAPI that packet reception needs to be scheduled
+ */
+
+static irqreturn_t
+ks8695_rx_irq(int irq, void *dev_id)
+{
+ struct net_device *ndev = (struct net_device *)dev_id;
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ spin_lock(&ksp->rx_lock);
+
+ if (napi_schedule_prep(&ksp->napi)) {
+ unsigned long status = readl(KS8695_IRQ_VA + KS8695_INTEN);
+ unsigned long mask_bit = 1 << ks8695_get_rx_enable_bit(ksp);
+ /*disable rx interrupt*/
+ status &= ~mask_bit;
+ writel(status , KS8695_IRQ_VA + KS8695_INTEN);
+ __napi_schedule(&ksp->napi);
+ }
+
+ spin_unlock(&ksp->rx_lock);
+ return IRQ_HANDLED;
+}
+
+/**
+ * ks8695_rx - Receive packets called by NAPI poll method
+ * @ksp: Private data for the KS8695 Ethernet
+ * @budget: Number of packets allowed to process
+ */
+static int ks8695_rx(struct ks8695_priv *ksp, int budget)
+{
+ struct net_device *ndev = ksp->ndev;
+ struct sk_buff *skb;
+ int buff_n;
+ u32 flags;
+ int pktlen;
+ int received = 0;
+
+ buff_n = ksp->next_rx_desc_read;
+ while (received < budget
+ && ksp->rx_buffers[buff_n].skb
+ && (!(ksp->rx_ring[buff_n].status &
+ cpu_to_le32(RDES_OWN)))) {
+ rmb();
+ flags = le32_to_cpu(ksp->rx_ring[buff_n].status);
+
+ /* Found an SKB which we own, this means we
+ * received a packet
+ */
+ if ((flags & (RDES_FS | RDES_LS)) !=
+ (RDES_FS | RDES_LS)) {
+ /* This packet is not the first and
+ * the last segment. Therefore it is
+ * a "spanning" packet and we can't
+ * handle it
+ */
+ goto rx_failure;
+ }
+
+ if (flags & (RDES_ES | RDES_RE)) {
+ /* It's an error packet */
+ ndev->stats.rx_errors++;
+ if (flags & RDES_TL)
+ ndev->stats.rx_length_errors++;
+ if (flags & RDES_RF)
+ ndev->stats.rx_length_errors++;
+ if (flags & RDES_CE)
+ ndev->stats.rx_crc_errors++;
+ if (flags & RDES_RE)
+ ndev->stats.rx_missed_errors++;
+
+ goto rx_failure;
+ }
+
+ pktlen = flags & RDES_FLEN;
+ pktlen -= 4; /* Drop the CRC */
+
+ /* Retrieve the sk_buff */
+ skb = ksp->rx_buffers[buff_n].skb;
+
+ /* Clear it from the ring */
+ ksp->rx_buffers[buff_n].skb = NULL;
+ ksp->rx_ring[buff_n].data_ptr = 0;
+
+ /* Unmap the SKB */
+ dma_unmap_single(ksp->dev,
+ ksp->rx_buffers[buff_n].dma_ptr,
+ ksp->rx_buffers[buff_n].length,
+ DMA_FROM_DEVICE);
+
+ /* Relinquish the SKB to the network layer */
+ skb_put(skb, pktlen);
+ skb->protocol = eth_type_trans(skb, ndev);
+ netif_receive_skb(skb);
+
+ /* Record stats */
+ ndev->stats.rx_packets++;
+ ndev->stats.rx_bytes += pktlen;
+ goto rx_finished;
+
+rx_failure:
+ /* This ring entry is an error, but we can
+ * re-use the skb
+ */
+ /* Give the ring entry back to the hardware */
+ ksp->rx_ring[buff_n].status = cpu_to_le32(RDES_OWN);
+rx_finished:
+ received++;
+ buff_n = (buff_n + 1) & MAX_RX_DESC_MASK;
+ }
+
+ /* And note which RX descriptor we last did */
+ ksp->next_rx_desc_read = buff_n;
+
+ /* And refill the buffers */
+ ks8695_refill_rxbuffers(ksp);
+
+ /* Kick the RX DMA engine, in case it became suspended */
+ ks8695_writereg(ksp, KS8695_DRSC, 0);
+
+ return received;
+}
+
+
+/**
+ * ks8695_poll - Receive packet by NAPI poll method
+ * @ksp: Private data for the KS8695 Ethernet
+ * @budget: The remaining number packets for network subsystem
+ *
+ * Invoked by the network core when it requests for new
+ * packets from the driver
+ */
+static int ks8695_poll(struct napi_struct *napi, int budget)
+{
+ struct ks8695_priv *ksp = container_of(napi, struct ks8695_priv, napi);
+ unsigned long work_done;
+
+ unsigned long isr = readl(KS8695_IRQ_VA + KS8695_INTEN);
+ unsigned long mask_bit = 1 << ks8695_get_rx_enable_bit(ksp);
+
+ work_done = ks8695_rx(ksp, budget);
+
+ if (work_done < budget) {
+ unsigned long flags;
+ spin_lock_irqsave(&ksp->rx_lock, flags);
+ __napi_complete(napi);
+ /*enable rx interrupt*/
+ writel(isr | mask_bit, KS8695_IRQ_VA + KS8695_INTEN);
+ spin_unlock_irqrestore(&ksp->rx_lock, flags);
+ }
+ return work_done;
+}
+
+/**
+ * ks8695_link_irq - Link change IRQ handler
+ * @irq: The IRQ which went off (ignored)
+ * @dev_id: The net_device for the interrupt
+ *
+ * The WAN interface can generate an IRQ when the link changes,
+ * report this to the net layer and the user.
+ */
+static irqreturn_t
+ks8695_link_irq(int irq, void *dev_id)
+{
+ struct net_device *ndev = (struct net_device *)dev_id;
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ u32 ctrl;
+
+ ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
+ if (ctrl & WMC_WLS) {
+ netif_carrier_on(ndev);
+ if (netif_msg_link(ksp))
+ dev_info(ksp->dev,
+ "%s: Link is now up (10%sMbps/%s-duplex)\n",
+ ndev->name,
+ (ctrl & WMC_WSS) ? "0" : "",
+ (ctrl & WMC_WDS) ? "Full" : "Half");
+ } else {
+ netif_carrier_off(ndev);
+ if (netif_msg_link(ksp))
+ dev_info(ksp->dev, "%s: Link is now down.\n",
+ ndev->name);
+ }
+
+ return IRQ_HANDLED;
+}
+
+
+/* KS8695 Device functions */
+
+/**
+ * ks8695_reset - Reset a KS8695 ethernet interface
+ * @ksp: The interface to reset
+ *
+ * Perform an engine reset of the interface and re-program it
+ * with sensible defaults.
+ */
+static void
+ks8695_reset(struct ks8695_priv *ksp)
+{
+ int reset_timeout = watchdog;
+ /* Issue the reset via the TX DMA control register */
+ ks8695_writereg(ksp, KS8695_DTXC, DTXC_TRST);
+ while (reset_timeout--) {
+ if (!(ks8695_readreg(ksp, KS8695_DTXC) & DTXC_TRST))
+ break;
+ msleep(1);
+ }
+
+ if (reset_timeout < 0) {
+ dev_crit(ksp->dev,
+ "Timeout waiting for DMA engines to reset\n");
+ /* And blithely carry on */
+ }
+
+ /* Definitely wait long enough before attempting to program
+ * the engines
+ */
+ msleep(10);
+
+ /* RX: unicast and broadcast */
+ ks8695_writereg(ksp, KS8695_DRXC, DRXC_RU | DRXC_RB);
+ /* TX: pad and add CRC */
+ ks8695_writereg(ksp, KS8695_DTXC, DTXC_TEP | DTXC_TAC);
+}
+
+/**
+ * ks8695_shutdown - Shut down a KS8695 ethernet interface
+ * @ksp: The interface to shut down
+ *
+ * This disables packet RX/TX, cleans up IRQs, drains the rings,
+ * and basically places the interface into a clean shutdown
+ * state.
+ */
+static void
+ks8695_shutdown(struct ks8695_priv *ksp)
+{
+ u32 ctrl;
+ int buff_n;
+
+ /* Disable packet transmission */
+ ctrl = ks8695_readreg(ksp, KS8695_DTXC);
+ ks8695_writereg(ksp, KS8695_DTXC, ctrl & ~DTXC_TE);
+
+ /* Disable packet reception */
+ ctrl = ks8695_readreg(ksp, KS8695_DRXC);
+ ks8695_writereg(ksp, KS8695_DRXC, ctrl & ~DRXC_RE);
+
+ /* Release the IRQs */
+ free_irq(ksp->rx_irq, ksp->ndev);
+ free_irq(ksp->tx_irq, ksp->ndev);
+ if (ksp->link_irq != -1)
+ free_irq(ksp->link_irq, ksp->ndev);
+
+ /* Throw away any pending TX packets */
+ for (buff_n = 0; buff_n < MAX_TX_DESC; ++buff_n) {
+ if (ksp->tx_buffers[buff_n].skb) {
+ /* Remove this SKB from the TX ring */
+ ksp->tx_ring[buff_n].owner = 0;
+ ksp->tx_ring[buff_n].status = 0;
+ ksp->tx_ring[buff_n].data_ptr = 0;
+
+ /* Unmap and bin this SKB */
+ dma_unmap_single(ksp->dev,
+ ksp->tx_buffers[buff_n].dma_ptr,
+ ksp->tx_buffers[buff_n].length,
+ DMA_TO_DEVICE);
+ dev_kfree_skb_irq(ksp->tx_buffers[buff_n].skb);
+ ksp->tx_buffers[buff_n].skb = NULL;
+ }
+ }
+
+ /* Purge the RX buffers */
+ for (buff_n = 0; buff_n < MAX_RX_DESC; ++buff_n) {
+ if (ksp->rx_buffers[buff_n].skb) {
+ /* Remove the SKB from the RX ring */
+ ksp->rx_ring[buff_n].status = 0;
+ ksp->rx_ring[buff_n].data_ptr = 0;
+
+ /* Unmap and bin the SKB */
+ dma_unmap_single(ksp->dev,
+ ksp->rx_buffers[buff_n].dma_ptr,
+ ksp->rx_buffers[buff_n].length,
+ DMA_FROM_DEVICE);
+ dev_kfree_skb_irq(ksp->rx_buffers[buff_n].skb);
+ ksp->rx_buffers[buff_n].skb = NULL;
+ }
+ }
+}
+
+
+/**
+ * ks8695_setup_irq - IRQ setup helper function
+ * @irq: The IRQ number to claim
+ * @irq_name: The name to give the IRQ claimant
+ * @handler: The function to call to handle the IRQ
+ * @ndev: The net_device to pass in as the dev_id argument to the handler
+ *
+ * Return 0 on success.
+ */
+static int
+ks8695_setup_irq(int irq, const char *irq_name,
+ irq_handler_t handler, struct net_device *ndev)
+{
+ int ret;
+
+ ret = request_irq(irq, handler, IRQF_SHARED, irq_name, ndev);
+
+ if (ret) {
+ dev_err(&ndev->dev, "failure to request IRQ %d\n", irq);
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * ks8695_init_net - Initialise a KS8695 ethernet interface
+ * @ksp: The interface to initialise
+ *
+ * This routine fills the RX ring, initialises the DMA engines,
+ * allocates the IRQs and then starts the packet TX and RX
+ * engines.
+ */
+static int
+ks8695_init_net(struct ks8695_priv *ksp)
+{
+ int ret;
+ u32 ctrl;
+
+ ks8695_refill_rxbuffers(ksp);
+
+ /* Initialise the DMA engines */
+ ks8695_writereg(ksp, KS8695_RDLB, (u32) ksp->rx_ring_dma);
+ ks8695_writereg(ksp, KS8695_TDLB, (u32) ksp->tx_ring_dma);
+
+ /* Request the IRQs */
+ ret = ks8695_setup_irq(ksp->rx_irq, ksp->rx_irq_name,
+ ks8695_rx_irq, ksp->ndev);
+ if (ret)
+ return ret;
+ ret = ks8695_setup_irq(ksp->tx_irq, ksp->tx_irq_name,
+ ks8695_tx_irq, ksp->ndev);
+ if (ret)
+ return ret;
+ if (ksp->link_irq != -1) {
+ ret = ks8695_setup_irq(ksp->link_irq, ksp->link_irq_name,
+ ks8695_link_irq, ksp->ndev);
+ if (ret)
+ return ret;
+ }
+
+ /* Set up the ring indices */
+ ksp->next_rx_desc_read = 0;
+ ksp->tx_ring_next_slot = 0;
+ ksp->tx_ring_used = 0;
+
+ /* Bring up transmission */
+ ctrl = ks8695_readreg(ksp, KS8695_DTXC);
+ /* Enable packet transmission */
+ ks8695_writereg(ksp, KS8695_DTXC, ctrl | DTXC_TE);
+
+ /* Bring up the reception */
+ ctrl = ks8695_readreg(ksp, KS8695_DRXC);
+ /* Enable packet reception */
+ ks8695_writereg(ksp, KS8695_DRXC, ctrl | DRXC_RE);
+ /* And start the DMA engine */
+ ks8695_writereg(ksp, KS8695_DRSC, 0);
+
+ /* All done */
+ return 0;
+}
+
+/**
+ * ks8695_release_device - HW resource release for KS8695 e-net
+ * @ksp: The device to be freed
+ *
+ * This unallocates io memory regions, dma-coherent regions etc
+ * which were allocated in ks8695_probe.
+ */
+static void
+ks8695_release_device(struct ks8695_priv *ksp)
+{
+ /* Unmap the registers */
+ iounmap(ksp->io_regs);
+ if (ksp->phyiface_regs)
+ iounmap(ksp->phyiface_regs);
+
+ /* And release the request */
+ release_resource(ksp->regs_req);
+ kfree(ksp->regs_req);
+ if (ksp->phyiface_req) {
+ release_resource(ksp->phyiface_req);
+ kfree(ksp->phyiface_req);
+ }
+
+ /* Free the ring buffers */
+ dma_free_coherent(ksp->dev, RING_DMA_SIZE,
+ ksp->ring_base, ksp->ring_base_dma);
+}
+
+/* Ethtool support */
+
+/**
+ * ks8695_get_msglevel - Get the messages enabled for emission
+ * @ndev: The network device to read from
+ */
+static u32
+ks8695_get_msglevel(struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ return ksp->msg_enable;
+}
+
+/**
+ * ks8695_set_msglevel - Set the messages enabled for emission
+ * @ndev: The network device to configure
+ * @value: The messages to set for emission
+ */
+static void
+ks8695_set_msglevel(struct net_device *ndev, u32 value)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ ksp->msg_enable = value;
+}
+
+/**
+ * ks8695_wan_get_settings - Get device-specific settings.
+ * @ndev: The network device to read settings from
+ * @cmd: The ethtool structure to read into
+ */
+static int
+ks8695_wan_get_settings(struct net_device *ndev, struct ethtool_cmd *cmd)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ u32 ctrl;
+
+ /* All ports on the KS8695 support these... */
+ cmd->supported = (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
+ SUPPORTED_TP | SUPPORTED_MII);
+ cmd->transceiver = XCVR_INTERNAL;
+
+ cmd->advertising = ADVERTISED_TP | ADVERTISED_MII;
+ cmd->port = PORT_MII;
+ cmd->supported |= (SUPPORTED_Autoneg | SUPPORTED_Pause);
+ cmd->phy_address = 0;
+
+ ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
+ if ((ctrl & WMC_WAND) == 0) {
+ /* auto-negotiation is enabled */
+ cmd->advertising |= ADVERTISED_Autoneg;
+ if (ctrl & WMC_WANA100F)
+ cmd->advertising |= ADVERTISED_100baseT_Full;
+ if (ctrl & WMC_WANA100H)
+ cmd->advertising |= ADVERTISED_100baseT_Half;
+ if (ctrl & WMC_WANA10F)
+ cmd->advertising |= ADVERTISED_10baseT_Full;
+ if (ctrl & WMC_WANA10H)
+ cmd->advertising |= ADVERTISED_10baseT_Half;
+ if (ctrl & WMC_WANAP)
+ cmd->advertising |= ADVERTISED_Pause;
+ cmd->autoneg = AUTONEG_ENABLE;
+
+ ethtool_cmd_speed_set(cmd,
+ (ctrl & WMC_WSS) ? SPEED_100 : SPEED_10);
+ cmd->duplex = (ctrl & WMC_WDS) ?
+ DUPLEX_FULL : DUPLEX_HALF;
+ } else {
+ /* auto-negotiation is disabled */
+ cmd->autoneg = AUTONEG_DISABLE;
+
+ ethtool_cmd_speed_set(cmd, ((ctrl & WMC_WANF100) ?
+ SPEED_100 : SPEED_10));
+ cmd->duplex = (ctrl & WMC_WANFF) ?
+ DUPLEX_FULL : DUPLEX_HALF;
+ }
+
+ return 0;
+}
+
+/**
+ * ks8695_wan_set_settings - Set device-specific settings.
+ * @ndev: The network device to configure
+ * @cmd: The settings to configure
+ */
+static int
+ks8695_wan_set_settings(struct net_device *ndev, struct ethtool_cmd *cmd)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ u32 ctrl;
+
+ if ((cmd->speed != SPEED_10) && (cmd->speed != SPEED_100))
+ return -EINVAL;
+ if ((cmd->duplex != DUPLEX_HALF) && (cmd->duplex != DUPLEX_FULL))
+ return -EINVAL;
+ if (cmd->port != PORT_MII)
+ return -EINVAL;
+ if (cmd->transceiver != XCVR_INTERNAL)
+ return -EINVAL;
+ if ((cmd->autoneg != AUTONEG_DISABLE) &&
+ (cmd->autoneg != AUTONEG_ENABLE))
+ return -EINVAL;
+
+ if (cmd->autoneg == AUTONEG_ENABLE) {
+ if ((cmd->advertising & (ADVERTISED_10baseT_Half |
+ ADVERTISED_10baseT_Full |
+ ADVERTISED_100baseT_Half |
+ ADVERTISED_100baseT_Full)) == 0)
+ return -EINVAL;
+
+ ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
+
+ ctrl &= ~(WMC_WAND | WMC_WANA100F | WMC_WANA100H |
+ WMC_WANA10F | WMC_WANA10H);
+ if (cmd->advertising & ADVERTISED_100baseT_Full)
+ ctrl |= WMC_WANA100F;
+ if (cmd->advertising & ADVERTISED_100baseT_Half)
+ ctrl |= WMC_WANA100H;
+ if (cmd->advertising & ADVERTISED_10baseT_Full)
+ ctrl |= WMC_WANA10F;
+ if (cmd->advertising & ADVERTISED_10baseT_Half)
+ ctrl |= WMC_WANA10H;
+
+ /* force a re-negotiation */
+ ctrl |= WMC_WANR;
+ writel(ctrl, ksp->phyiface_regs + KS8695_WMC);
+ } else {
+ ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
+
+ /* disable auto-negotiation */
+ ctrl |= WMC_WAND;
+ ctrl &= ~(WMC_WANF100 | WMC_WANFF);
+
+ if (cmd->speed == SPEED_100)
+ ctrl |= WMC_WANF100;
+ if (cmd->duplex == DUPLEX_FULL)
+ ctrl |= WMC_WANFF;
+
+ writel(ctrl, ksp->phyiface_regs + KS8695_WMC);
+ }
+
+ return 0;
+}
+
+/**
+ * ks8695_wan_nwayreset - Restart the autonegotiation on the port.
+ * @ndev: The network device to restart autoneotiation on
+ */
+static int
+ks8695_wan_nwayreset(struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ u32 ctrl;
+
+ ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
+
+ if ((ctrl & WMC_WAND) == 0)
+ writel(ctrl | WMC_WANR,
+ ksp->phyiface_regs + KS8695_WMC);
+ else
+ /* auto-negotiation not enabled */
+ return -EINVAL;
+
+ return 0;
+}
+
+/**
+ * ks8695_wan_get_pause - Retrieve network pause/flow-control advertising
+ * @ndev: The device to retrieve settings from
+ * @param: The structure to fill out with the information
+ */
+static void
+ks8695_wan_get_pause(struct net_device *ndev, struct ethtool_pauseparam *param)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ u32 ctrl;
+
+ ctrl = readl(ksp->phyiface_regs + KS8695_WMC);
+
+ /* advertise Pause */
+ param->autoneg = (ctrl & WMC_WANAP);
+
+ /* current Rx Flow-control */
+ ctrl = ks8695_readreg(ksp, KS8695_DRXC);
+ param->rx_pause = (ctrl & DRXC_RFCE);
+
+ /* current Tx Flow-control */
+ ctrl = ks8695_readreg(ksp, KS8695_DTXC);
+ param->tx_pause = (ctrl & DTXC_TFCE);
+}
+
+/**
+ * ks8695_get_drvinfo - Retrieve driver information
+ * @ndev: The network device to retrieve info about
+ * @info: The info structure to fill out.
+ */
+static void
+ks8695_get_drvinfo(struct net_device *ndev, struct ethtool_drvinfo *info)
+{
+ strlcpy(info->driver, MODULENAME, sizeof(info->driver));
+ strlcpy(info->version, MODULEVERSION, sizeof(info->version));
+ strlcpy(info->bus_info, dev_name(ndev->dev.parent),
+ sizeof(info->bus_info));
+}
+
+static const struct ethtool_ops ks8695_ethtool_ops = {
+ .get_msglevel = ks8695_get_msglevel,
+ .set_msglevel = ks8695_set_msglevel,
+ .get_drvinfo = ks8695_get_drvinfo,
+};
+
+static const struct ethtool_ops ks8695_wan_ethtool_ops = {
+ .get_msglevel = ks8695_get_msglevel,
+ .set_msglevel = ks8695_set_msglevel,
+ .get_settings = ks8695_wan_get_settings,
+ .set_settings = ks8695_wan_set_settings,
+ .nway_reset = ks8695_wan_nwayreset,
+ .get_link = ethtool_op_get_link,
+ .get_pauseparam = ks8695_wan_get_pause,
+ .get_drvinfo = ks8695_get_drvinfo,
+};
+
+/* Network device interface functions */
+
+/**
+ * ks8695_set_mac - Update MAC in net dev and HW
+ * @ndev: The network device to update
+ * @addr: The new MAC address to set
+ */
+static int
+ks8695_set_mac(struct net_device *ndev, void *addr)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ struct sockaddr *address = addr;
+
+ if (!is_valid_ether_addr(address->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(ndev->dev_addr, address->sa_data, ndev->addr_len);
+
+ ks8695_update_mac(ksp);
+
+ dev_dbg(ksp->dev, "%s: Updated MAC address to %pM\n",
+ ndev->name, ndev->dev_addr);
+
+ return 0;
+}
+
+/**
+ * ks8695_set_multicast - Set up the multicast behaviour of the interface
+ * @ndev: The net_device to configure
+ *
+ * This routine, called by the net layer, configures promiscuity
+ * and multicast reception behaviour for the interface.
+ */
+static void
+ks8695_set_multicast(struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ u32 ctrl;
+
+ ctrl = ks8695_readreg(ksp, KS8695_DRXC);
+
+ if (ndev->flags & IFF_PROMISC) {
+ /* enable promiscuous mode */
+ ctrl |= DRXC_RA;
+ } else if (ndev->flags & ~IFF_PROMISC) {
+ /* disable promiscuous mode */
+ ctrl &= ~DRXC_RA;
+ }
+
+ if (ndev->flags & IFF_ALLMULTI) {
+ /* enable all multicast mode */
+ ctrl |= DRXC_RM;
+ } else if (netdev_mc_count(ndev) > KS8695_NR_ADDRESSES) {
+ /* more specific multicast addresses than can be
+ * handled in hardware
+ */
+ ctrl |= DRXC_RM;
+ } else {
+ /* enable specific multicasts */
+ ctrl &= ~DRXC_RM;
+ ks8695_init_partial_multicast(ksp, ndev);
+ }
+
+ ks8695_writereg(ksp, KS8695_DRXC, ctrl);
+}
+
+/**
+ * ks8695_timeout - Handle a network tx/rx timeout.
+ * @ndev: The net_device which timed out.
+ *
+ * A network transaction timed out, reset the device.
+ */
+static void
+ks8695_timeout(struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ netif_stop_queue(ndev);
+ ks8695_shutdown(ksp);
+
+ ks8695_reset(ksp);
+
+ ks8695_update_mac(ksp);
+
+ /* We ignore the return from this since it managed to init
+ * before it probably will be okay to init again.
+ */
+ ks8695_init_net(ksp);
+
+ /* Reconfigure promiscuity etc */
+ ks8695_set_multicast(ndev);
+
+ /* And start the TX queue once more */
+ netif_start_queue(ndev);
+}
+
+/**
+ * ks8695_start_xmit - Start a packet transmission
+ * @skb: The packet to transmit
+ * @ndev: The network device to send the packet on
+ *
+ * This routine, called by the net layer, takes ownership of the
+ * sk_buff and adds it to the TX ring. It then kicks the TX DMA
+ * engine to ensure transmission begins.
+ */
+static int
+ks8695_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ int buff_n;
+ dma_addr_t dmap;
+
+ spin_lock_irq(&ksp->txq_lock);
+
+ if (ksp->tx_ring_used == MAX_TX_DESC) {
+ /* Somehow we got entered when we have no room */
+ spin_unlock_irq(&ksp->txq_lock);
+ return NETDEV_TX_BUSY;
+ }
+
+ buff_n = ksp->tx_ring_next_slot;
+
+ BUG_ON(ksp->tx_buffers[buff_n].skb);
+
+ dmap = dma_map_single(ksp->dev, skb->data, skb->len, DMA_TO_DEVICE);
+ if (unlikely(dma_mapping_error(ksp->dev, dmap))) {
+ /* Failed to DMA map this SKB, give it back for now */
+ spin_unlock_irq(&ksp->txq_lock);
+ dev_dbg(ksp->dev, "%s: Could not map DMA memory for "\
+ "transmission, trying later\n", ndev->name);
+ return NETDEV_TX_BUSY;
+ }
+
+ ksp->tx_buffers[buff_n].dma_ptr = dmap;
+ /* Mapped okay, store the buffer pointer and length for later */
+ ksp->tx_buffers[buff_n].skb = skb;
+ ksp->tx_buffers[buff_n].length = skb->len;
+
+ /* Fill out the TX descriptor */
+ ksp->tx_ring[buff_n].data_ptr =
+ cpu_to_le32(ksp->tx_buffers[buff_n].dma_ptr);
+ ksp->tx_ring[buff_n].status =
+ cpu_to_le32(TDES_IC | TDES_FS | TDES_LS |
+ (skb->len & TDES_TBS));
+
+ wmb();
+
+ /* Hand it over to the hardware */
+ ksp->tx_ring[buff_n].owner = cpu_to_le32(TDES_OWN);
+
+ if (++ksp->tx_ring_used == MAX_TX_DESC)
+ netif_stop_queue(ndev);
+
+ /* Kick the TX DMA in case it decided to go IDLE */
+ ks8695_writereg(ksp, KS8695_DTSC, 0);
+
+ /* And update the next ring slot */
+ ksp->tx_ring_next_slot = (buff_n + 1) & MAX_TX_DESC_MASK;
+
+ spin_unlock_irq(&ksp->txq_lock);
+ return NETDEV_TX_OK;
+}
+
+/**
+ * ks8695_stop - Stop (shutdown) a KS8695 ethernet interface
+ * @ndev: The net_device to stop
+ *
+ * This disables the TX queue and cleans up a KS8695 ethernet
+ * device.
+ */
+static int
+ks8695_stop(struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ netif_stop_queue(ndev);
+ napi_disable(&ksp->napi);
+
+ ks8695_shutdown(ksp);
+
+ return 0;
+}
+
+/**
+ * ks8695_open - Open (bring up) a KS8695 ethernet interface
+ * @ndev: The net_device to open
+ *
+ * This resets, configures the MAC, initialises the RX ring and
+ * DMA engines and starts the TX queue for a KS8695 ethernet
+ * device.
+ */
+static int
+ks8695_open(struct net_device *ndev)
+{
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+ int ret;
+
+ if (!is_valid_ether_addr(ndev->dev_addr))
+ return -EADDRNOTAVAIL;
+
+ ks8695_reset(ksp);
+
+ ks8695_update_mac(ksp);
+
+ ret = ks8695_init_net(ksp);
+ if (ret) {
+ ks8695_shutdown(ksp);
+ return ret;
+ }
+
+ napi_enable(&ksp->napi);
+ netif_start_queue(ndev);
+
+ return 0;
+}
+
+/* Platform device driver */
+
+/**
+ * ks8695_init_switch - Init LAN switch to known good defaults.
+ * @ksp: The device to initialise
+ *
+ * This initialises the LAN switch in the KS8695 to a known-good
+ * set of defaults.
+ */
+static void __devinit
+ks8695_init_switch(struct ks8695_priv *ksp)
+{
+ u32 ctrl;
+
+ /* Default value for SEC0 according to datasheet */
+ ctrl = 0x40819e00;
+
+ /* LED0 = Speed LED1 = Link/Activity */
+ ctrl &= ~(SEC0_LLED1S | SEC0_LLED0S);
+ ctrl |= (LLED0S_LINK | LLED1S_LINK_ACTIVITY);
+
+ /* Enable Switch */
+ ctrl |= SEC0_ENABLE;
+
+ writel(ctrl, ksp->phyiface_regs + KS8695_SEC0);
+
+ /* Defaults for SEC1 */
+ writel(0x9400100, ksp->phyiface_regs + KS8695_SEC1);
+}
+
+/**
+ * ks8695_init_wan_phy - Initialise the WAN PHY to sensible defaults
+ * @ksp: The device to initialise
+ *
+ * This initialises a KS8695's WAN phy to sensible values for
+ * autonegotiation etc.
+ */
+static void __devinit
+ks8695_init_wan_phy(struct ks8695_priv *ksp)
+{
+ u32 ctrl;
+
+ /* Support auto-negotiation */
+ ctrl = (WMC_WANAP | WMC_WANA100F | WMC_WANA100H |
+ WMC_WANA10F | WMC_WANA10H);
+
+ /* LED0 = Activity , LED1 = Link */
+ ctrl |= (WLED0S_ACTIVITY | WLED1S_LINK);
+
+ /* Restart Auto-negotiation */
+ ctrl |= WMC_WANR;
+
+ writel(ctrl, ksp->phyiface_regs + KS8695_WMC);
+
+ writel(0, ksp->phyiface_regs + KS8695_WPPM);
+ writel(0, ksp->phyiface_regs + KS8695_PPS);
+}
+
+static const struct net_device_ops ks8695_netdev_ops = {
+ .ndo_open = ks8695_open,
+ .ndo_stop = ks8695_stop,
+ .ndo_start_xmit = ks8695_start_xmit,
+ .ndo_tx_timeout = ks8695_timeout,
+ .ndo_set_mac_address = ks8695_set_mac,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_multicast_list = ks8695_set_multicast,
+};
+
+/**
+ * ks8695_probe - Probe and initialise a KS8695 ethernet interface
+ * @pdev: The platform device to probe
+ *
+ * Initialise a KS8695 ethernet device from platform data.
+ *
+ * This driver requires at least one IORESOURCE_MEM for the
+ * registers and two IORESOURCE_IRQ for the RX and TX IRQs
+ * respectively. It can optionally take an additional
+ * IORESOURCE_MEM for the switch or phy in the case of the lan or
+ * wan ports, and an IORESOURCE_IRQ for the link IRQ for the wan
+ * port.
+ */
+static int __devinit
+ks8695_probe(struct platform_device *pdev)
+{
+ struct ks8695_priv *ksp;
+ struct net_device *ndev;
+ struct resource *regs_res, *phyiface_res;
+ struct resource *rxirq_res, *txirq_res, *linkirq_res;
+ int ret = 0;
+ int buff_n;
+ u32 machigh, maclow;
+
+ /* Initialise a net_device */
+ ndev = alloc_etherdev(sizeof(struct ks8695_priv));
+ if (!ndev) {
+ dev_err(&pdev->dev, "could not allocate device.\n");
+ return -ENOMEM;
+ }
+
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+
+ dev_dbg(&pdev->dev, "ks8695_probe() called\n");
+
+ /* Configure our private structure a little */
+ ksp = netdev_priv(ndev);
+
+ ksp->dev = &pdev->dev;
+ ksp->ndev = ndev;
+ ksp->msg_enable = NETIF_MSG_LINK;
+
+ /* Retrieve resources */
+ regs_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phyiface_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+ rxirq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ txirq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 1);
+ linkirq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 2);
+
+ if (!(regs_res && rxirq_res && txirq_res)) {
+ dev_err(ksp->dev, "insufficient resources\n");
+ ret = -ENOENT;
+ goto failure;
+ }
+
+ ksp->regs_req = request_mem_region(regs_res->start,
+ resource_size(regs_res),
+ pdev->name);
+
+ if (!ksp->regs_req) {
+ dev_err(ksp->dev, "cannot claim register space\n");
+ ret = -EIO;
+ goto failure;
+ }
+
+ ksp->io_regs = ioremap(regs_res->start, resource_size(regs_res));
+
+ if (!ksp->io_regs) {
+ dev_err(ksp->dev, "failed to ioremap registers\n");
+ ret = -EINVAL;
+ goto failure;
+ }
+
+ if (phyiface_res) {
+ ksp->phyiface_req =
+ request_mem_region(phyiface_res->start,
+ resource_size(phyiface_res),
+ phyiface_res->name);
+
+ if (!ksp->phyiface_req) {
+ dev_err(ksp->dev,
+ "cannot claim switch register space\n");
+ ret = -EIO;
+ goto failure;
+ }
+
+ ksp->phyiface_regs = ioremap(phyiface_res->start,
+ resource_size(phyiface_res));
+
+ if (!ksp->phyiface_regs) {
+ dev_err(ksp->dev,
+ "failed to ioremap switch registers\n");
+ ret = -EINVAL;
+ goto failure;
+ }
+ }
+
+ ksp->rx_irq = rxirq_res->start;
+ ksp->rx_irq_name = rxirq_res->name ? rxirq_res->name : "Ethernet RX";
+ ksp->tx_irq = txirq_res->start;
+ ksp->tx_irq_name = txirq_res->name ? txirq_res->name : "Ethernet TX";
+ ksp->link_irq = (linkirq_res ? linkirq_res->start : -1);
+ ksp->link_irq_name = (linkirq_res && linkirq_res->name) ?
+ linkirq_res->name : "Ethernet Link";
+
+ /* driver system setup */
+ ndev->netdev_ops = &ks8695_netdev_ops;
+ ndev->watchdog_timeo = msecs_to_jiffies(watchdog);
+
+ netif_napi_add(ndev, &ksp->napi, ks8695_poll, NAPI_WEIGHT);
+
+ /* Retrieve the default MAC addr from the chip. */
+ /* The bootloader should have left it in there for us. */
+
+ machigh = ks8695_readreg(ksp, KS8695_MAH);
+ maclow = ks8695_readreg(ksp, KS8695_MAL);
+
+ ndev->dev_addr[0] = (machigh >> 8) & 0xFF;
+ ndev->dev_addr[1] = machigh & 0xFF;
+ ndev->dev_addr[2] = (maclow >> 24) & 0xFF;
+ ndev->dev_addr[3] = (maclow >> 16) & 0xFF;
+ ndev->dev_addr[4] = (maclow >> 8) & 0xFF;
+ ndev->dev_addr[5] = maclow & 0xFF;
+
+ if (!is_valid_ether_addr(ndev->dev_addr))
+ dev_warn(ksp->dev, "%s: Invalid ethernet MAC address. Please "
+ "set using ifconfig\n", ndev->name);
+
+ /* In order to be efficient memory-wise, we allocate both
+ * rings in one go.
+ */
+ ksp->ring_base = dma_alloc_coherent(&pdev->dev, RING_DMA_SIZE,
+ &ksp->ring_base_dma, GFP_KERNEL);
+ if (!ksp->ring_base) {
+ ret = -ENOMEM;
+ goto failure;
+ }
+
+ /* Specify the TX DMA ring buffer */
+ ksp->tx_ring = ksp->ring_base;
+ ksp->tx_ring_dma = ksp->ring_base_dma;
+
+ /* And initialise the queue's lock */
+ spin_lock_init(&ksp->txq_lock);
+ spin_lock_init(&ksp->rx_lock);
+
+ /* Specify the RX DMA ring buffer */
+ ksp->rx_ring = ksp->ring_base + TX_RING_DMA_SIZE;
+ ksp->rx_ring_dma = ksp->ring_base_dma + TX_RING_DMA_SIZE;
+
+ /* Zero the descriptor rings */
+ memset(ksp->tx_ring, 0, TX_RING_DMA_SIZE);
+ memset(ksp->rx_ring, 0, RX_RING_DMA_SIZE);
+
+ /* Build the rings */
+ for (buff_n = 0; buff_n < MAX_TX_DESC; ++buff_n) {
+ ksp->tx_ring[buff_n].next_desc =
+ cpu_to_le32(ksp->tx_ring_dma +
+ (sizeof(struct tx_ring_desc) *
+ ((buff_n + 1) & MAX_TX_DESC_MASK)));
+ }
+
+ for (buff_n = 0; buff_n < MAX_RX_DESC; ++buff_n) {
+ ksp->rx_ring[buff_n].next_desc =
+ cpu_to_le32(ksp->rx_ring_dma +
+ (sizeof(struct rx_ring_desc) *
+ ((buff_n + 1) & MAX_RX_DESC_MASK)));
+ }
+
+ /* Initialise the port (physically) */
+ if (ksp->phyiface_regs && ksp->link_irq == -1) {
+ ks8695_init_switch(ksp);
+ ksp->dtype = KS8695_DTYPE_LAN;
+ SET_ETHTOOL_OPS(ndev, &ks8695_ethtool_ops);
+ } else if (ksp->phyiface_regs && ksp->link_irq != -1) {
+ ks8695_init_wan_phy(ksp);
+ ksp->dtype = KS8695_DTYPE_WAN;
+ SET_ETHTOOL_OPS(ndev, &ks8695_wan_ethtool_ops);
+ } else {
+ /* No initialisation since HPNA does not have a PHY */
+ ksp->dtype = KS8695_DTYPE_HPNA;
+ SET_ETHTOOL_OPS(ndev, &ks8695_ethtool_ops);
+ }
+
+ /* And bring up the net_device with the net core */
+ platform_set_drvdata(pdev, ndev);
+ ret = register_netdev(ndev);
+
+ if (ret == 0) {
+ dev_info(ksp->dev, "ks8695 ethernet (%s) MAC: %pM\n",
+ ks8695_port_type(ksp), ndev->dev_addr);
+ } else {
+ /* Report the failure to register the net_device */
+ dev_err(ksp->dev, "ks8695net: failed to register netdev.\n");
+ goto failure;
+ }
+
+ /* All is well */
+ return 0;
+
+ /* Error exit path */
+failure:
+ ks8695_release_device(ksp);
+ free_netdev(ndev);
+
+ return ret;
+}
+
+/**
+ * ks8695_drv_suspend - Suspend a KS8695 ethernet platform device.
+ * @pdev: The device to suspend
+ * @state: The suspend state
+ *
+ * This routine detaches and shuts down a KS8695 ethernet device.
+ */
+static int
+ks8695_drv_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ ksp->in_suspend = 1;
+
+ if (netif_running(ndev)) {
+ netif_device_detach(ndev);
+ ks8695_shutdown(ksp);
+ }
+
+ return 0;
+}
+
+/**
+ * ks8695_drv_resume - Resume a KS8695 ethernet platform device.
+ * @pdev: The device to resume
+ *
+ * This routine re-initialises and re-attaches a KS8695 ethernet
+ * device.
+ */
+static int
+ks8695_drv_resume(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ ks8695_reset(ksp);
+ ks8695_init_net(ksp);
+ ks8695_set_multicast(ndev);
+ netif_device_attach(ndev);
+ }
+
+ ksp->in_suspend = 0;
+
+ return 0;
+}
+
+/**
+ * ks8695_drv_remove - Remove a KS8695 net device on driver unload.
+ * @pdev: The platform device to remove
+ *
+ * This unregisters and releases a KS8695 ethernet device.
+ */
+static int __devexit
+ks8695_drv_remove(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct ks8695_priv *ksp = netdev_priv(ndev);
+
+ platform_set_drvdata(pdev, NULL);
+ netif_napi_del(&ksp->napi);
+
+ unregister_netdev(ndev);
+ ks8695_release_device(ksp);
+ free_netdev(ndev);
+
+ dev_dbg(&pdev->dev, "released and freed device\n");
+ return 0;
+}
+
+static struct platform_driver ks8695_driver = {
+ .driver = {
+ .name = MODULENAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = ks8695_probe,
+ .remove = __devexit_p(ks8695_drv_remove),
+ .suspend = ks8695_drv_suspend,
+ .resume = ks8695_drv_resume,
+};
+
+/* Module interface */
+
+static int __init
+ks8695_init(void)
+{
+ printk(KERN_INFO "%s Ethernet driver, V%s\n",
+ MODULENAME, MODULEVERSION);
+
+ return platform_driver_register(&ks8695_driver);
+}
+
+static void __exit
+ks8695_cleanup(void)
+{
+ platform_driver_unregister(&ks8695_driver);
+}
+
+module_init(ks8695_init);
+module_exit(ks8695_cleanup);
+
+MODULE_AUTHOR("Simtec Electronics");
+MODULE_DESCRIPTION("Micrel KS8695 (Centaur) Ethernet driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" MODULENAME);
+
+module_param(watchdog, int, 0400);
+MODULE_PARM_DESC(watchdog, "transmit timeout in milliseconds");
--- /dev/null
+/*
+ * Micrel KS8695 (Centaur) Ethernet.
+ *
+ * Copyright 2008 Simtec Electronics
+ * Daniel Silverstone <dsilvers@simtec.co.uk>
+ * Vincent Sanders <vince@simtec.co.uk>
+ */
+
+#ifndef KS8695NET_H
+#define KS8695NET_H
+
+/* Receive descriptor flags */
+#define RDES_OWN (1 << 31) /* Ownership */
+#define RDES_FS (1 << 30) /* First Descriptor */
+#define RDES_LS (1 << 29) /* Last Descriptor */
+#define RDES_IPE (1 << 28) /* IP Checksum error */
+#define RDES_TCPE (1 << 27) /* TCP Checksum error */
+#define RDES_UDPE (1 << 26) /* UDP Checksum error */
+#define RDES_ES (1 << 25) /* Error summary */
+#define RDES_MF (1 << 24) /* Multicast Frame */
+#define RDES_RE (1 << 19) /* MII Error reported */
+#define RDES_TL (1 << 18) /* Frame too Long */
+#define RDES_RF (1 << 17) /* Runt Frame */
+#define RDES_CE (1 << 16) /* CRC error */
+#define RDES_FT (1 << 15) /* Frame Type */
+#define RDES_FLEN (0x7ff) /* Frame Length */
+
+#define RDES_RER (1 << 25) /* Receive End of Ring */
+#define RDES_RBS (0x7ff) /* Receive Buffer Size */
+
+/* Transmit descriptor flags */
+
+#define TDES_OWN (1 << 31) /* Ownership */
+
+#define TDES_IC (1 << 31) /* Interrupt on Completion */
+#define TDES_FS (1 << 30) /* First Segment */
+#define TDES_LS (1 << 29) /* Last Segment */
+#define TDES_IPCKG (1 << 28) /* IP Checksum generate */
+#define TDES_TCPCKG (1 << 27) /* TCP Checksum generate */
+#define TDES_UDPCKG (1 << 26) /* UDP Checksum generate */
+#define TDES_TER (1 << 25) /* Transmit End of Ring */
+#define TDES_TBS (0x7ff) /* Transmit Buffer Size */
+
+/*
+ * Network controller register offsets
+ */
+#define KS8695_DTXC (0x00) /* DMA Transmit Control */
+#define KS8695_DRXC (0x04) /* DMA Receive Control */
+#define KS8695_DTSC (0x08) /* DMA Transmit Start Command */
+#define KS8695_DRSC (0x0c) /* DMA Receive Start Command */
+#define KS8695_TDLB (0x10) /* Transmit Descriptor List
+ * Base Address
+ */
+#define KS8695_RDLB (0x14) /* Receive Descriptor List
+ * Base Address
+ */
+#define KS8695_MAL (0x18) /* MAC Station Address Low */
+#define KS8695_MAH (0x1c) /* MAC Station Address High */
+#define KS8695_AAL_(n) (0x80 + ((n)*8)) /* MAC Additional
+ * Station Address
+ * (0..15) Low
+ */
+#define KS8695_AAH_(n) (0x84 + ((n)*8)) /* MAC Additional
+ * Station Address
+ * (0..15) High
+ */
+
+
+/* DMA Transmit Control Register */
+#define DTXC_TRST (1 << 31) /* Soft Reset */
+#define DTXC_TBS (0x3f << 24) /* Transmit Burst Size */
+#define DTXC_TUCG (1 << 18) /* Transmit UDP
+ * Checksum Generate
+ */
+#define DTXC_TTCG (1 << 17) /* Transmit TCP
+ * Checksum Generate
+ */
+#define DTXC_TICG (1 << 16) /* Transmit IP
+ * Checksum Generate
+ */
+#define DTXC_TFCE (1 << 9) /* Transmit Flow
+ * Control Enable
+ */
+#define DTXC_TLB (1 << 8) /* Loopback mode */
+#define DTXC_TEP (1 << 2) /* Transmit Enable Padding */
+#define DTXC_TAC (1 << 1) /* Transmit Add CRC */
+#define DTXC_TE (1 << 0) /* TX Enable */
+
+/* DMA Receive Control Register */
+#define DRXC_RBS (0x3f << 24) /* Receive Burst Size */
+#define DRXC_RUCC (1 << 18) /* Receive UDP Checksum check */
+#define DRXC_RTCG (1 << 17) /* Receive TCP Checksum check */
+#define DRXC_RICG (1 << 16) /* Receive IP Checksum check */
+#define DRXC_RFCE (1 << 9) /* Receive Flow Control
+ * Enable
+ */
+#define DRXC_RB (1 << 6) /* Receive Broadcast */
+#define DRXC_RM (1 << 5) /* Receive Multicast */
+#define DRXC_RU (1 << 4) /* Receive Unicast */
+#define DRXC_RERR (1 << 3) /* Receive Error Frame */
+#define DRXC_RA (1 << 2) /* Receive All */
+#define DRXC_RE (1 << 0) /* RX Enable */
+
+/* Additional Station Address High */
+#define AAH_E (1 << 31) /* Address Enabled */
+
+#endif /* KS8695NET_H */
--- /dev/null
+/*
+ * ks8842.c timberdale KS8842 ethernet driver
+ * Copyright (c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * The Micrel KS8842 behind the timberdale FPGA
+ * The genuine Micrel KS8841/42 device with ISA 16/32bit bus interface
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/ks8842.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+
+#define DRV_NAME "ks8842"
+
+/* Timberdale specific Registers */
+#define REG_TIMB_RST 0x1c
+#define REG_TIMB_FIFO 0x20
+#define REG_TIMB_ISR 0x24
+#define REG_TIMB_IER 0x28
+#define REG_TIMB_IAR 0x2C
+#define REQ_TIMB_DMA_RESUME 0x30
+
+/* KS8842 registers */
+
+#define REG_SELECT_BANK 0x0e
+
+/* bank 0 registers */
+#define REG_QRFCR 0x04
+
+/* bank 2 registers */
+#define REG_MARL 0x00
+#define REG_MARM 0x02
+#define REG_MARH 0x04
+
+/* bank 3 registers */
+#define REG_GRR 0x06
+
+/* bank 16 registers */
+#define REG_TXCR 0x00
+#define REG_TXSR 0x02
+#define REG_RXCR 0x04
+#define REG_TXMIR 0x08
+#define REG_RXMIR 0x0A
+
+/* bank 17 registers */
+#define REG_TXQCR 0x00
+#define REG_RXQCR 0x02
+#define REG_TXFDPR 0x04
+#define REG_RXFDPR 0x06
+#define REG_QMU_DATA_LO 0x08
+#define REG_QMU_DATA_HI 0x0A
+
+/* bank 18 registers */
+#define REG_IER 0x00
+#define IRQ_LINK_CHANGE 0x8000
+#define IRQ_TX 0x4000
+#define IRQ_RX 0x2000
+#define IRQ_RX_OVERRUN 0x0800
+#define IRQ_TX_STOPPED 0x0200
+#define IRQ_RX_STOPPED 0x0100
+#define IRQ_RX_ERROR 0x0080
+#define ENABLED_IRQS (IRQ_LINK_CHANGE | IRQ_TX | IRQ_RX | IRQ_RX_STOPPED | \
+ IRQ_TX_STOPPED | IRQ_RX_OVERRUN | IRQ_RX_ERROR)
+/* When running via timberdale in DMA mode, the RX interrupt should be
+ enabled in the KS8842, but not in the FPGA IP, since the IP handles
+ RX DMA internally.
+ TX interrupts are not needed it is handled by the FPGA the driver is
+ notified via DMA callbacks.
+*/
+#define ENABLED_IRQS_DMA_IP (IRQ_LINK_CHANGE | IRQ_RX_STOPPED | \
+ IRQ_TX_STOPPED | IRQ_RX_OVERRUN | IRQ_RX_ERROR)
+#define ENABLED_IRQS_DMA (ENABLED_IRQS_DMA_IP | IRQ_RX)
+#define REG_ISR 0x02
+#define REG_RXSR 0x04
+#define RXSR_VALID 0x8000
+#define RXSR_BROADCAST 0x80
+#define RXSR_MULTICAST 0x40
+#define RXSR_UNICAST 0x20
+#define RXSR_FRAMETYPE 0x08
+#define RXSR_TOO_LONG 0x04
+#define RXSR_RUNT 0x02
+#define RXSR_CRC_ERROR 0x01
+#define RXSR_ERROR (RXSR_TOO_LONG | RXSR_RUNT | RXSR_CRC_ERROR)
+
+/* bank 32 registers */
+#define REG_SW_ID_AND_ENABLE 0x00
+#define REG_SGCR1 0x02
+#define REG_SGCR2 0x04
+#define REG_SGCR3 0x06
+
+/* bank 39 registers */
+#define REG_MACAR1 0x00
+#define REG_MACAR2 0x02
+#define REG_MACAR3 0x04
+
+/* bank 45 registers */
+#define REG_P1MBCR 0x00
+#define REG_P1MBSR 0x02
+
+/* bank 46 registers */
+#define REG_P2MBCR 0x00
+#define REG_P2MBSR 0x02
+
+/* bank 48 registers */
+#define REG_P1CR2 0x02
+
+/* bank 49 registers */
+#define REG_P1CR4 0x02
+#define REG_P1SR 0x04
+
+/* flags passed by platform_device for configuration */
+#define MICREL_KS884X 0x01 /* 0=Timeberdale(FPGA), 1=Micrel */
+#define KS884X_16BIT 0x02 /* 1=16bit, 0=32bit */
+
+#define DMA_BUFFER_SIZE 2048
+
+struct ks8842_tx_dma_ctl {
+ struct dma_chan *chan;
+ struct dma_async_tx_descriptor *adesc;
+ void *buf;
+ struct scatterlist sg;
+ int channel;
+};
+
+struct ks8842_rx_dma_ctl {
+ struct dma_chan *chan;
+ struct dma_async_tx_descriptor *adesc;
+ struct sk_buff *skb;
+ struct scatterlist sg;
+ struct tasklet_struct tasklet;
+ int channel;
+};
+
+#define KS8842_USE_DMA(adapter) (((adapter)->dma_tx.channel != -1) && \
+ ((adapter)->dma_rx.channel != -1))
+
+struct ks8842_adapter {
+ void __iomem *hw_addr;
+ int irq;
+ unsigned long conf_flags; /* copy of platform_device config */
+ struct tasklet_struct tasklet;
+ spinlock_t lock; /* spinlock to be interrupt safe */
+ struct work_struct timeout_work;
+ struct net_device *netdev;
+ struct device *dev;
+ struct ks8842_tx_dma_ctl dma_tx;
+ struct ks8842_rx_dma_ctl dma_rx;
+};
+
+static void ks8842_dma_rx_cb(void *data);
+static void ks8842_dma_tx_cb(void *data);
+
+static inline void ks8842_resume_dma(struct ks8842_adapter *adapter)
+{
+ iowrite32(1, adapter->hw_addr + REQ_TIMB_DMA_RESUME);
+}
+
+static inline void ks8842_select_bank(struct ks8842_adapter *adapter, u16 bank)
+{
+ iowrite16(bank, adapter->hw_addr + REG_SELECT_BANK);
+}
+
+static inline void ks8842_write8(struct ks8842_adapter *adapter, u16 bank,
+ u8 value, int offset)
+{
+ ks8842_select_bank(adapter, bank);
+ iowrite8(value, adapter->hw_addr + offset);
+}
+
+static inline void ks8842_write16(struct ks8842_adapter *adapter, u16 bank,
+ u16 value, int offset)
+{
+ ks8842_select_bank(adapter, bank);
+ iowrite16(value, adapter->hw_addr + offset);
+}
+
+static inline void ks8842_enable_bits(struct ks8842_adapter *adapter, u16 bank,
+ u16 bits, int offset)
+{
+ u16 reg;
+ ks8842_select_bank(adapter, bank);
+ reg = ioread16(adapter->hw_addr + offset);
+ reg |= bits;
+ iowrite16(reg, adapter->hw_addr + offset);
+}
+
+static inline void ks8842_clear_bits(struct ks8842_adapter *adapter, u16 bank,
+ u16 bits, int offset)
+{
+ u16 reg;
+ ks8842_select_bank(adapter, bank);
+ reg = ioread16(adapter->hw_addr + offset);
+ reg &= ~bits;
+ iowrite16(reg, adapter->hw_addr + offset);
+}
+
+static inline void ks8842_write32(struct ks8842_adapter *adapter, u16 bank,
+ u32 value, int offset)
+{
+ ks8842_select_bank(adapter, bank);
+ iowrite32(value, adapter->hw_addr + offset);
+}
+
+static inline u8 ks8842_read8(struct ks8842_adapter *adapter, u16 bank,
+ int offset)
+{
+ ks8842_select_bank(adapter, bank);
+ return ioread8(adapter->hw_addr + offset);
+}
+
+static inline u16 ks8842_read16(struct ks8842_adapter *adapter, u16 bank,
+ int offset)
+{
+ ks8842_select_bank(adapter, bank);
+ return ioread16(adapter->hw_addr + offset);
+}
+
+static inline u32 ks8842_read32(struct ks8842_adapter *adapter, u16 bank,
+ int offset)
+{
+ ks8842_select_bank(adapter, bank);
+ return ioread32(adapter->hw_addr + offset);
+}
+
+static void ks8842_reset(struct ks8842_adapter *adapter)
+{
+ if (adapter->conf_flags & MICREL_KS884X) {
+ ks8842_write16(adapter, 3, 1, REG_GRR);
+ msleep(10);
+ iowrite16(0, adapter->hw_addr + REG_GRR);
+ } else {
+ /* The KS8842 goes haywire when doing softare reset
+ * a work around in the timberdale IP is implemented to
+ * do a hardware reset instead
+ ks8842_write16(adapter, 3, 1, REG_GRR);
+ msleep(10);
+ iowrite16(0, adapter->hw_addr + REG_GRR);
+ */
+ iowrite32(0x1, adapter->hw_addr + REG_TIMB_RST);
+ msleep(20);
+ }
+}
+
+static void ks8842_update_link_status(struct net_device *netdev,
+ struct ks8842_adapter *adapter)
+{
+ /* check the status of the link */
+ if (ks8842_read16(adapter, 45, REG_P1MBSR) & 0x4) {
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
+ } else {
+ netif_stop_queue(netdev);
+ netif_carrier_off(netdev);
+ }
+}
+
+static void ks8842_enable_tx(struct ks8842_adapter *adapter)
+{
+ ks8842_enable_bits(adapter, 16, 0x01, REG_TXCR);
+}
+
+static void ks8842_disable_tx(struct ks8842_adapter *adapter)
+{
+ ks8842_clear_bits(adapter, 16, 0x01, REG_TXCR);
+}
+
+static void ks8842_enable_rx(struct ks8842_adapter *adapter)
+{
+ ks8842_enable_bits(adapter, 16, 0x01, REG_RXCR);
+}
+
+static void ks8842_disable_rx(struct ks8842_adapter *adapter)
+{
+ ks8842_clear_bits(adapter, 16, 0x01, REG_RXCR);
+}
+
+static void ks8842_reset_hw(struct ks8842_adapter *adapter)
+{
+ /* reset the HW */
+ ks8842_reset(adapter);
+
+ /* Enable QMU Transmit flow control / transmit padding / Transmit CRC */
+ ks8842_write16(adapter, 16, 0x000E, REG_TXCR);
+
+ /* enable the receiver, uni + multi + broadcast + flow ctrl
+ + crc strip */
+ ks8842_write16(adapter, 16, 0x8 | 0x20 | 0x40 | 0x80 | 0x400,
+ REG_RXCR);
+
+ /* TX frame pointer autoincrement */
+ ks8842_write16(adapter, 17, 0x4000, REG_TXFDPR);
+
+ /* RX frame pointer autoincrement */
+ ks8842_write16(adapter, 17, 0x4000, REG_RXFDPR);
+
+ /* RX 2 kb high watermark */
+ ks8842_write16(adapter, 0, 0x1000, REG_QRFCR);
+
+ /* aggressive back off in half duplex */
+ ks8842_enable_bits(adapter, 32, 1 << 8, REG_SGCR1);
+
+ /* enable no excessive collison drop */
+ ks8842_enable_bits(adapter, 32, 1 << 3, REG_SGCR2);
+
+ /* Enable port 1 force flow control / back pressure / transmit / recv */
+ ks8842_write16(adapter, 48, 0x1E07, REG_P1CR2);
+
+ /* restart port auto-negotiation */
+ ks8842_enable_bits(adapter, 49, 1 << 13, REG_P1CR4);
+
+ /* Enable the transmitter */
+ ks8842_enable_tx(adapter);
+
+ /* Enable the receiver */
+ ks8842_enable_rx(adapter);
+
+ /* clear all interrupts */
+ ks8842_write16(adapter, 18, 0xffff, REG_ISR);
+
+ /* enable interrupts */
+ if (KS8842_USE_DMA(adapter)) {
+ /* When running in DMA Mode the RX interrupt is not enabled in
+ timberdale because RX data is received by DMA callbacks
+ it must still be enabled in the KS8842 because it indicates
+ to timberdale when there is RX data for it's DMA FIFOs */
+ iowrite16(ENABLED_IRQS_DMA_IP, adapter->hw_addr + REG_TIMB_IER);
+ ks8842_write16(adapter, 18, ENABLED_IRQS_DMA, REG_IER);
+ } else {
+ if (!(adapter->conf_flags & MICREL_KS884X))
+ iowrite16(ENABLED_IRQS,
+ adapter->hw_addr + REG_TIMB_IER);
+ ks8842_write16(adapter, 18, ENABLED_IRQS, REG_IER);
+ }
+ /* enable the switch */
+ ks8842_write16(adapter, 32, 0x1, REG_SW_ID_AND_ENABLE);
+}
+
+static void ks8842_read_mac_addr(struct ks8842_adapter *adapter, u8 *dest)
+{
+ int i;
+ u16 mac;
+
+ for (i = 0; i < ETH_ALEN; i++)
+ dest[ETH_ALEN - i - 1] = ks8842_read8(adapter, 2, REG_MARL + i);
+
+ if (adapter->conf_flags & MICREL_KS884X) {
+ /*
+ the sequence of saving mac addr between MAC and Switch is
+ different.
+ */
+
+ mac = ks8842_read16(adapter, 2, REG_MARL);
+ ks8842_write16(adapter, 39, mac, REG_MACAR3);
+ mac = ks8842_read16(adapter, 2, REG_MARM);
+ ks8842_write16(adapter, 39, mac, REG_MACAR2);
+ mac = ks8842_read16(adapter, 2, REG_MARH);
+ ks8842_write16(adapter, 39, mac, REG_MACAR1);
+ } else {
+
+ /* make sure the switch port uses the same MAC as the QMU */
+ mac = ks8842_read16(adapter, 2, REG_MARL);
+ ks8842_write16(adapter, 39, mac, REG_MACAR1);
+ mac = ks8842_read16(adapter, 2, REG_MARM);
+ ks8842_write16(adapter, 39, mac, REG_MACAR2);
+ mac = ks8842_read16(adapter, 2, REG_MARH);
+ ks8842_write16(adapter, 39, mac, REG_MACAR3);
+ }
+}
+
+static void ks8842_write_mac_addr(struct ks8842_adapter *adapter, u8 *mac)
+{
+ unsigned long flags;
+ unsigned i;
+
+ spin_lock_irqsave(&adapter->lock, flags);
+ for (i = 0; i < ETH_ALEN; i++) {
+ ks8842_write8(adapter, 2, mac[ETH_ALEN - i - 1], REG_MARL + i);
+ if (!(adapter->conf_flags & MICREL_KS884X))
+ ks8842_write8(adapter, 39, mac[ETH_ALEN - i - 1],
+ REG_MACAR1 + i);
+ }
+
+ if (adapter->conf_flags & MICREL_KS884X) {
+ /*
+ the sequence of saving mac addr between MAC and Switch is
+ different.
+ */
+
+ u16 mac;
+
+ mac = ks8842_read16(adapter, 2, REG_MARL);
+ ks8842_write16(adapter, 39, mac, REG_MACAR3);
+ mac = ks8842_read16(adapter, 2, REG_MARM);
+ ks8842_write16(adapter, 39, mac, REG_MACAR2);
+ mac = ks8842_read16(adapter, 2, REG_MARH);
+ ks8842_write16(adapter, 39, mac, REG_MACAR1);
+ }
+ spin_unlock_irqrestore(&adapter->lock, flags);
+}
+
+static inline u16 ks8842_tx_fifo_space(struct ks8842_adapter *adapter)
+{
+ return ks8842_read16(adapter, 16, REG_TXMIR) & 0x1fff;
+}
+
+static int ks8842_tx_frame_dma(struct sk_buff *skb, struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct ks8842_tx_dma_ctl *ctl = &adapter->dma_tx;
+ u8 *buf = ctl->buf;
+
+ if (ctl->adesc) {
+ netdev_dbg(netdev, "%s: TX ongoing\n", __func__);
+ /* transfer ongoing */
+ return NETDEV_TX_BUSY;
+ }
+
+ sg_dma_len(&ctl->sg) = skb->len + sizeof(u32);
+
+ /* copy data to the TX buffer */
+ /* the control word, enable IRQ, port 1 and the length */
+ *buf++ = 0x00;
+ *buf++ = 0x01; /* Port 1 */
+ *buf++ = skb->len & 0xff;
+ *buf++ = (skb->len >> 8) & 0xff;
+ skb_copy_from_linear_data(skb, buf, skb->len);
+
+ dma_sync_single_range_for_device(adapter->dev,
+ sg_dma_address(&ctl->sg), 0, sg_dma_len(&ctl->sg),
+ DMA_TO_DEVICE);
+
+ /* make sure the length is a multiple of 4 */
+ if (sg_dma_len(&ctl->sg) % 4)
+ sg_dma_len(&ctl->sg) += 4 - sg_dma_len(&ctl->sg) % 4;
+
+ ctl->adesc = ctl->chan->device->device_prep_slave_sg(ctl->chan,
+ &ctl->sg, 1, DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_COMPL_SKIP_SRC_UNMAP);
+ if (!ctl->adesc)
+ return NETDEV_TX_BUSY;
+
+ ctl->adesc->callback_param = netdev;
+ ctl->adesc->callback = ks8842_dma_tx_cb;
+ ctl->adesc->tx_submit(ctl->adesc);
+
+ netdev->stats.tx_bytes += skb->len;
+
+ dev_kfree_skb(skb);
+
+ return NETDEV_TX_OK;
+}
+
+static int ks8842_tx_frame(struct sk_buff *skb, struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ int len = skb->len;
+
+ netdev_dbg(netdev, "%s: len %u head %p data %p tail %p end %p\n",
+ __func__, skb->len, skb->head, skb->data,
+ skb_tail_pointer(skb), skb_end_pointer(skb));
+
+ /* check FIFO buffer space, we need space for CRC and command bits */
+ if (ks8842_tx_fifo_space(adapter) < len + 8)
+ return NETDEV_TX_BUSY;
+
+ if (adapter->conf_flags & KS884X_16BIT) {
+ u16 *ptr16 = (u16 *)skb->data;
+ ks8842_write16(adapter, 17, 0x8000 | 0x100, REG_QMU_DATA_LO);
+ ks8842_write16(adapter, 17, (u16)len, REG_QMU_DATA_HI);
+ netdev->stats.tx_bytes += len;
+
+ /* copy buffer */
+ while (len > 0) {
+ iowrite16(*ptr16++, adapter->hw_addr + REG_QMU_DATA_LO);
+ iowrite16(*ptr16++, adapter->hw_addr + REG_QMU_DATA_HI);
+ len -= sizeof(u32);
+ }
+ } else {
+
+ u32 *ptr = (u32 *)skb->data;
+ u32 ctrl;
+ /* the control word, enable IRQ, port 1 and the length */
+ ctrl = 0x8000 | 0x100 | (len << 16);
+ ks8842_write32(adapter, 17, ctrl, REG_QMU_DATA_LO);
+
+ netdev->stats.tx_bytes += len;
+
+ /* copy buffer */
+ while (len > 0) {
+ iowrite32(*ptr, adapter->hw_addr + REG_QMU_DATA_LO);
+ len -= sizeof(u32);
+ ptr++;
+ }
+ }
+
+ /* enqueue packet */
+ ks8842_write16(adapter, 17, 1, REG_TXQCR);
+
+ dev_kfree_skb(skb);
+
+ return NETDEV_TX_OK;
+}
+
+static void ks8842_update_rx_err_counters(struct net_device *netdev, u32 status)
+{
+ netdev_dbg(netdev, "RX error, status: %x\n", status);
+
+ netdev->stats.rx_errors++;
+ if (status & RXSR_TOO_LONG)
+ netdev->stats.rx_length_errors++;
+ if (status & RXSR_CRC_ERROR)
+ netdev->stats.rx_crc_errors++;
+ if (status & RXSR_RUNT)
+ netdev->stats.rx_frame_errors++;
+}
+
+static void ks8842_update_rx_counters(struct net_device *netdev, u32 status,
+ int len)
+{
+ netdev_dbg(netdev, "RX packet, len: %d\n", len);
+
+ netdev->stats.rx_packets++;
+ netdev->stats.rx_bytes += len;
+ if (status & RXSR_MULTICAST)
+ netdev->stats.multicast++;
+}
+
+static int __ks8842_start_new_rx_dma(struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct ks8842_rx_dma_ctl *ctl = &adapter->dma_rx;
+ struct scatterlist *sg = &ctl->sg;
+ int err;
+
+ ctl->skb = netdev_alloc_skb(netdev, DMA_BUFFER_SIZE);
+ if (ctl->skb) {
+ sg_init_table(sg, 1);
+ sg_dma_address(sg) = dma_map_single(adapter->dev,
+ ctl->skb->data, DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
+ err = dma_mapping_error(adapter->dev, sg_dma_address(sg));
+ if (unlikely(err)) {
+ sg_dma_address(sg) = 0;
+ goto out;
+ }
+
+ sg_dma_len(sg) = DMA_BUFFER_SIZE;
+
+ ctl->adesc = ctl->chan->device->device_prep_slave_sg(ctl->chan,
+ sg, 1, DMA_FROM_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_COMPL_SKIP_SRC_UNMAP);
+
+ if (!ctl->adesc)
+ goto out;
+
+ ctl->adesc->callback_param = netdev;
+ ctl->adesc->callback = ks8842_dma_rx_cb;
+ ctl->adesc->tx_submit(ctl->adesc);
+ } else {
+ err = -ENOMEM;
+ sg_dma_address(sg) = 0;
+ goto out;
+ }
+
+ return err;
+out:
+ if (sg_dma_address(sg))
+ dma_unmap_single(adapter->dev, sg_dma_address(sg),
+ DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
+ sg_dma_address(sg) = 0;
+ if (ctl->skb)
+ dev_kfree_skb(ctl->skb);
+
+ ctl->skb = NULL;
+
+ printk(KERN_ERR DRV_NAME": Failed to start RX DMA: %d\n", err);
+ return err;
+}
+
+static void ks8842_rx_frame_dma_tasklet(unsigned long arg)
+{
+ struct net_device *netdev = (struct net_device *)arg;
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct ks8842_rx_dma_ctl *ctl = &adapter->dma_rx;
+ struct sk_buff *skb = ctl->skb;
+ dma_addr_t addr = sg_dma_address(&ctl->sg);
+ u32 status;
+
+ ctl->adesc = NULL;
+
+ /* kick next transfer going */
+ __ks8842_start_new_rx_dma(netdev);
+
+ /* now handle the data we got */
+ dma_unmap_single(adapter->dev, addr, DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
+
+ status = *((u32 *)skb->data);
+
+ netdev_dbg(netdev, "%s - rx_data: status: %x\n",
+ __func__, status & 0xffff);
+
+ /* check the status */
+ if ((status & RXSR_VALID) && !(status & RXSR_ERROR)) {
+ int len = (status >> 16) & 0x7ff;
+
+ ks8842_update_rx_counters(netdev, status, len);
+
+ /* reserve 4 bytes which is the status word */
+ skb_reserve(skb, 4);
+ skb_put(skb, len);
+
+ skb->protocol = eth_type_trans(skb, netdev);
+ netif_rx(skb);
+ } else {
+ ks8842_update_rx_err_counters(netdev, status);
+ dev_kfree_skb(skb);
+ }
+}
+
+static void ks8842_rx_frame(struct net_device *netdev,
+ struct ks8842_adapter *adapter)
+{
+ u32 status;
+ int len;
+
+ if (adapter->conf_flags & KS884X_16BIT) {
+ status = ks8842_read16(adapter, 17, REG_QMU_DATA_LO);
+ len = ks8842_read16(adapter, 17, REG_QMU_DATA_HI);
+ netdev_dbg(netdev, "%s - rx_data: status: %x\n",
+ __func__, status);
+ } else {
+ status = ks8842_read32(adapter, 17, REG_QMU_DATA_LO);
+ len = (status >> 16) & 0x7ff;
+ status &= 0xffff;
+ netdev_dbg(netdev, "%s - rx_data: status: %x\n",
+ __func__, status);
+ }
+
+ /* check the status */
+ if ((status & RXSR_VALID) && !(status & RXSR_ERROR)) {
+ struct sk_buff *skb = netdev_alloc_skb_ip_align(netdev, len + 3);
+
+ if (skb) {
+
+ ks8842_update_rx_counters(netdev, status, len);
+
+ if (adapter->conf_flags & KS884X_16BIT) {
+ u16 *data16 = (u16 *)skb_put(skb, len);
+ ks8842_select_bank(adapter, 17);
+ while (len > 0) {
+ *data16++ = ioread16(adapter->hw_addr +
+ REG_QMU_DATA_LO);
+ *data16++ = ioread16(adapter->hw_addr +
+ REG_QMU_DATA_HI);
+ len -= sizeof(u32);
+ }
+ } else {
+ u32 *data = (u32 *)skb_put(skb, len);
+
+ ks8842_select_bank(adapter, 17);
+ while (len > 0) {
+ *data++ = ioread32(adapter->hw_addr +
+ REG_QMU_DATA_LO);
+ len -= sizeof(u32);
+ }
+ }
+ skb->protocol = eth_type_trans(skb, netdev);
+ netif_rx(skb);
+ } else
+ netdev->stats.rx_dropped++;
+ } else
+ ks8842_update_rx_err_counters(netdev, status);
+
+ /* set high watermark to 3K */
+ ks8842_clear_bits(adapter, 0, 1 << 12, REG_QRFCR);
+
+ /* release the frame */
+ ks8842_write16(adapter, 17, 0x01, REG_RXQCR);
+
+ /* set high watermark to 2K */
+ ks8842_enable_bits(adapter, 0, 1 << 12, REG_QRFCR);
+}
+
+void ks8842_handle_rx(struct net_device *netdev, struct ks8842_adapter *adapter)
+{
+ u16 rx_data = ks8842_read16(adapter, 16, REG_RXMIR) & 0x1fff;
+ netdev_dbg(netdev, "%s Entry - rx_data: %d\n", __func__, rx_data);
+ while (rx_data) {
+ ks8842_rx_frame(netdev, adapter);
+ rx_data = ks8842_read16(adapter, 16, REG_RXMIR) & 0x1fff;
+ }
+}
+
+void ks8842_handle_tx(struct net_device *netdev, struct ks8842_adapter *adapter)
+{
+ u16 sr = ks8842_read16(adapter, 16, REG_TXSR);
+ netdev_dbg(netdev, "%s - entry, sr: %x\n", __func__, sr);
+ netdev->stats.tx_packets++;
+ if (netif_queue_stopped(netdev))
+ netif_wake_queue(netdev);
+}
+
+void ks8842_handle_rx_overrun(struct net_device *netdev,
+ struct ks8842_adapter *adapter)
+{
+ netdev_dbg(netdev, "%s: entry\n", __func__);
+ netdev->stats.rx_errors++;
+ netdev->stats.rx_fifo_errors++;
+}
+
+void ks8842_tasklet(unsigned long arg)
+{
+ struct net_device *netdev = (struct net_device *)arg;
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ u16 isr;
+ unsigned long flags;
+ u16 entry_bank;
+
+ /* read current bank to be able to set it back */
+ spin_lock_irqsave(&adapter->lock, flags);
+ entry_bank = ioread16(adapter->hw_addr + REG_SELECT_BANK);
+ spin_unlock_irqrestore(&adapter->lock, flags);
+
+ isr = ks8842_read16(adapter, 18, REG_ISR);
+ netdev_dbg(netdev, "%s - ISR: 0x%x\n", __func__, isr);
+
+ /* when running in DMA mode, do not ack RX interrupts, it is handled
+ internally by timberdale, otherwise it's DMA FIFO:s would stop
+ */
+ if (KS8842_USE_DMA(adapter))
+ isr &= ~IRQ_RX;
+
+ /* Ack */
+ ks8842_write16(adapter, 18, isr, REG_ISR);
+
+ if (!(adapter->conf_flags & MICREL_KS884X))
+ /* Ack in the timberdale IP as well */
+ iowrite32(0x1, adapter->hw_addr + REG_TIMB_IAR);
+
+ if (!netif_running(netdev))
+ return;
+
+ if (isr & IRQ_LINK_CHANGE)
+ ks8842_update_link_status(netdev, adapter);
+
+ /* should not get IRQ_RX when running DMA mode */
+ if (isr & (IRQ_RX | IRQ_RX_ERROR) && !KS8842_USE_DMA(adapter))
+ ks8842_handle_rx(netdev, adapter);
+
+ /* should only happen when in PIO mode */
+ if (isr & IRQ_TX)
+ ks8842_handle_tx(netdev, adapter);
+
+ if (isr & IRQ_RX_OVERRUN)
+ ks8842_handle_rx_overrun(netdev, adapter);
+
+ if (isr & IRQ_TX_STOPPED) {
+ ks8842_disable_tx(adapter);
+ ks8842_enable_tx(adapter);
+ }
+
+ if (isr & IRQ_RX_STOPPED) {
+ ks8842_disable_rx(adapter);
+ ks8842_enable_rx(adapter);
+ }
+
+ /* re-enable interrupts, put back the bank selection register */
+ spin_lock_irqsave(&adapter->lock, flags);
+ if (KS8842_USE_DMA(adapter))
+ ks8842_write16(adapter, 18, ENABLED_IRQS_DMA, REG_IER);
+ else
+ ks8842_write16(adapter, 18, ENABLED_IRQS, REG_IER);
+ iowrite16(entry_bank, adapter->hw_addr + REG_SELECT_BANK);
+
+ /* Make sure timberdale continues DMA operations, they are stopped while
+ we are handling the ks8842 because we might change bank */
+ if (KS8842_USE_DMA(adapter))
+ ks8842_resume_dma(adapter);
+
+ spin_unlock_irqrestore(&adapter->lock, flags);
+}
+
+static irqreturn_t ks8842_irq(int irq, void *devid)
+{
+ struct net_device *netdev = devid;
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ u16 isr;
+ u16 entry_bank = ioread16(adapter->hw_addr + REG_SELECT_BANK);
+ irqreturn_t ret = IRQ_NONE;
+
+ isr = ks8842_read16(adapter, 18, REG_ISR);
+ netdev_dbg(netdev, "%s - ISR: 0x%x\n", __func__, isr);
+
+ if (isr) {
+ if (KS8842_USE_DMA(adapter))
+ /* disable all but RX IRQ, since the FPGA relies on it*/
+ ks8842_write16(adapter, 18, IRQ_RX, REG_IER);
+ else
+ /* disable IRQ */
+ ks8842_write16(adapter, 18, 0x00, REG_IER);
+
+ /* schedule tasklet */
+ tasklet_schedule(&adapter->tasklet);
+
+ ret = IRQ_HANDLED;
+ }
+
+ iowrite16(entry_bank, adapter->hw_addr + REG_SELECT_BANK);
+
+ /* After an interrupt, tell timberdale to continue DMA operations.
+ DMA is disabled while we are handling the ks8842 because we might
+ change bank */
+ ks8842_resume_dma(adapter);
+
+ return ret;
+}
+
+static void ks8842_dma_rx_cb(void *data)
+{
+ struct net_device *netdev = data;
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+
+ netdev_dbg(netdev, "RX DMA finished\n");
+ /* schedule tasklet */
+ if (adapter->dma_rx.adesc)
+ tasklet_schedule(&adapter->dma_rx.tasklet);
+}
+
+static void ks8842_dma_tx_cb(void *data)
+{
+ struct net_device *netdev = data;
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct ks8842_tx_dma_ctl *ctl = &adapter->dma_tx;
+
+ netdev_dbg(netdev, "TX DMA finished\n");
+
+ if (!ctl->adesc)
+ return;
+
+ netdev->stats.tx_packets++;
+ ctl->adesc = NULL;
+
+ if (netif_queue_stopped(netdev))
+ netif_wake_queue(netdev);
+}
+
+static void ks8842_stop_dma(struct ks8842_adapter *adapter)
+{
+ struct ks8842_tx_dma_ctl *tx_ctl = &adapter->dma_tx;
+ struct ks8842_rx_dma_ctl *rx_ctl = &adapter->dma_rx;
+
+ tx_ctl->adesc = NULL;
+ if (tx_ctl->chan)
+ tx_ctl->chan->device->device_control(tx_ctl->chan,
+ DMA_TERMINATE_ALL, 0);
+
+ rx_ctl->adesc = NULL;
+ if (rx_ctl->chan)
+ rx_ctl->chan->device->device_control(rx_ctl->chan,
+ DMA_TERMINATE_ALL, 0);
+
+ if (sg_dma_address(&rx_ctl->sg))
+ dma_unmap_single(adapter->dev, sg_dma_address(&rx_ctl->sg),
+ DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
+ sg_dma_address(&rx_ctl->sg) = 0;
+
+ dev_kfree_skb(rx_ctl->skb);
+ rx_ctl->skb = NULL;
+}
+
+static void ks8842_dealloc_dma_bufs(struct ks8842_adapter *adapter)
+{
+ struct ks8842_tx_dma_ctl *tx_ctl = &adapter->dma_tx;
+ struct ks8842_rx_dma_ctl *rx_ctl = &adapter->dma_rx;
+
+ ks8842_stop_dma(adapter);
+
+ if (tx_ctl->chan)
+ dma_release_channel(tx_ctl->chan);
+ tx_ctl->chan = NULL;
+
+ if (rx_ctl->chan)
+ dma_release_channel(rx_ctl->chan);
+ rx_ctl->chan = NULL;
+
+ tasklet_kill(&rx_ctl->tasklet);
+
+ if (sg_dma_address(&tx_ctl->sg))
+ dma_unmap_single(adapter->dev, sg_dma_address(&tx_ctl->sg),
+ DMA_BUFFER_SIZE, DMA_TO_DEVICE);
+ sg_dma_address(&tx_ctl->sg) = 0;
+
+ kfree(tx_ctl->buf);
+ tx_ctl->buf = NULL;
+}
+
+static bool ks8842_dma_filter_fn(struct dma_chan *chan, void *filter_param)
+{
+ return chan->chan_id == (long)filter_param;
+}
+
+static int ks8842_alloc_dma_bufs(struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct ks8842_tx_dma_ctl *tx_ctl = &adapter->dma_tx;
+ struct ks8842_rx_dma_ctl *rx_ctl = &adapter->dma_rx;
+ int err;
+
+ dma_cap_mask_t mask;
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+ dma_cap_set(DMA_PRIVATE, mask);
+
+ sg_init_table(&tx_ctl->sg, 1);
+
+ tx_ctl->chan = dma_request_channel(mask, ks8842_dma_filter_fn,
+ (void *)(long)tx_ctl->channel);
+ if (!tx_ctl->chan) {
+ err = -ENODEV;
+ goto err;
+ }
+
+ /* allocate DMA buffer */
+ tx_ctl->buf = kmalloc(DMA_BUFFER_SIZE, GFP_KERNEL);
+ if (!tx_ctl->buf) {
+ err = -ENOMEM;
+ goto err;
+ }
+
+ sg_dma_address(&tx_ctl->sg) = dma_map_single(adapter->dev,
+ tx_ctl->buf, DMA_BUFFER_SIZE, DMA_TO_DEVICE);
+ err = dma_mapping_error(adapter->dev,
+ sg_dma_address(&tx_ctl->sg));
+ if (err) {
+ sg_dma_address(&tx_ctl->sg) = 0;
+ goto err;
+ }
+
+ rx_ctl->chan = dma_request_channel(mask, ks8842_dma_filter_fn,
+ (void *)(long)rx_ctl->channel);
+ if (!rx_ctl->chan) {
+ err = -ENODEV;
+ goto err;
+ }
+
+ tasklet_init(&rx_ctl->tasklet, ks8842_rx_frame_dma_tasklet,
+ (unsigned long)netdev);
+
+ return 0;
+err:
+ ks8842_dealloc_dma_bufs(adapter);
+ return err;
+}
+
+/* Netdevice operations */
+
+static int ks8842_open(struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ int err;
+
+ netdev_dbg(netdev, "%s - entry\n", __func__);
+
+ if (KS8842_USE_DMA(adapter)) {
+ err = ks8842_alloc_dma_bufs(netdev);
+
+ if (!err) {
+ /* start RX dma */
+ err = __ks8842_start_new_rx_dma(netdev);
+ if (err)
+ ks8842_dealloc_dma_bufs(adapter);
+ }
+
+ if (err) {
+ printk(KERN_WARNING DRV_NAME
+ ": Failed to initiate DMA, running PIO\n");
+ ks8842_dealloc_dma_bufs(adapter);
+ adapter->dma_rx.channel = -1;
+ adapter->dma_tx.channel = -1;
+ }
+ }
+
+ /* reset the HW */
+ ks8842_reset_hw(adapter);
+
+ ks8842_write_mac_addr(adapter, netdev->dev_addr);
+
+ ks8842_update_link_status(netdev, adapter);
+
+ err = request_irq(adapter->irq, ks8842_irq, IRQF_SHARED, DRV_NAME,
+ netdev);
+ if (err) {
+ pr_err("Failed to request IRQ: %d: %d\n", adapter->irq, err);
+ return err;
+ }
+
+ return 0;
+}
+
+static int ks8842_close(struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+
+ netdev_dbg(netdev, "%s - entry\n", __func__);
+
+ cancel_work_sync(&adapter->timeout_work);
+
+ if (KS8842_USE_DMA(adapter))
+ ks8842_dealloc_dma_bufs(adapter);
+
+ /* free the irq */
+ free_irq(adapter->irq, netdev);
+
+ /* disable the switch */
+ ks8842_write16(adapter, 32, 0x0, REG_SW_ID_AND_ENABLE);
+
+ return 0;
+}
+
+static netdev_tx_t ks8842_xmit_frame(struct sk_buff *skb,
+ struct net_device *netdev)
+{
+ int ret;
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+
+ netdev_dbg(netdev, "%s: entry\n", __func__);
+
+ if (KS8842_USE_DMA(adapter)) {
+ unsigned long flags;
+ ret = ks8842_tx_frame_dma(skb, netdev);
+ /* for now only allow one transfer at the time */
+ spin_lock_irqsave(&adapter->lock, flags);
+ if (adapter->dma_tx.adesc)
+ netif_stop_queue(netdev);
+ spin_unlock_irqrestore(&adapter->lock, flags);
+ return ret;
+ }
+
+ ret = ks8842_tx_frame(skb, netdev);
+
+ if (ks8842_tx_fifo_space(adapter) < netdev->mtu + 8)
+ netif_stop_queue(netdev);
+
+ return ret;
+}
+
+static int ks8842_set_mac(struct net_device *netdev, void *p)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct sockaddr *addr = p;
+ char *mac = (u8 *)addr->sa_data;
+
+ netdev_dbg(netdev, "%s: entry\n", __func__);
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(netdev->dev_addr, mac, netdev->addr_len);
+
+ ks8842_write_mac_addr(adapter, mac);
+ return 0;
+}
+
+static void ks8842_tx_timeout_work(struct work_struct *work)
+{
+ struct ks8842_adapter *adapter =
+ container_of(work, struct ks8842_adapter, timeout_work);
+ struct net_device *netdev = adapter->netdev;
+ unsigned long flags;
+
+ netdev_dbg(netdev, "%s: entry\n", __func__);
+
+ spin_lock_irqsave(&adapter->lock, flags);
+
+ if (KS8842_USE_DMA(adapter))
+ ks8842_stop_dma(adapter);
+
+ /* disable interrupts */
+ ks8842_write16(adapter, 18, 0, REG_IER);
+ ks8842_write16(adapter, 18, 0xFFFF, REG_ISR);
+
+ netif_stop_queue(netdev);
+
+ spin_unlock_irqrestore(&adapter->lock, flags);
+
+ ks8842_reset_hw(adapter);
+
+ ks8842_write_mac_addr(adapter, netdev->dev_addr);
+
+ ks8842_update_link_status(netdev, adapter);
+
+ if (KS8842_USE_DMA(adapter))
+ __ks8842_start_new_rx_dma(netdev);
+}
+
+static void ks8842_tx_timeout(struct net_device *netdev)
+{
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+
+ netdev_dbg(netdev, "%s: entry\n", __func__);
+
+ schedule_work(&adapter->timeout_work);
+}
+
+static const struct net_device_ops ks8842_netdev_ops = {
+ .ndo_open = ks8842_open,
+ .ndo_stop = ks8842_close,
+ .ndo_start_xmit = ks8842_xmit_frame,
+ .ndo_set_mac_address = ks8842_set_mac,
+ .ndo_tx_timeout = ks8842_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr
+};
+
+static const struct ethtool_ops ks8842_ethtool_ops = {
+ .get_link = ethtool_op_get_link,
+};
+
+static int __devinit ks8842_probe(struct platform_device *pdev)
+{
+ int err = -ENOMEM;
+ struct resource *iomem;
+ struct net_device *netdev;
+ struct ks8842_adapter *adapter;
+ struct ks8842_platform_data *pdata = pdev->dev.platform_data;
+ u16 id;
+ unsigned i;
+
+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!request_mem_region(iomem->start, resource_size(iomem), DRV_NAME))
+ goto err_mem_region;
+
+ netdev = alloc_etherdev(sizeof(struct ks8842_adapter));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ adapter = netdev_priv(netdev);
+ adapter->netdev = netdev;
+ INIT_WORK(&adapter->timeout_work, ks8842_tx_timeout_work);
+ adapter->hw_addr = ioremap(iomem->start, resource_size(iomem));
+ adapter->conf_flags = iomem->flags;
+
+ if (!adapter->hw_addr)
+ goto err_ioremap;
+
+ adapter->irq = platform_get_irq(pdev, 0);
+ if (adapter->irq < 0) {
+ err = adapter->irq;
+ goto err_get_irq;
+ }
+
+ adapter->dev = (pdev->dev.parent) ? pdev->dev.parent : &pdev->dev;
+
+ /* DMA is only supported when accessed via timberdale */
+ if (!(adapter->conf_flags & MICREL_KS884X) && pdata &&
+ (pdata->tx_dma_channel != -1) &&
+ (pdata->rx_dma_channel != -1)) {
+ adapter->dma_rx.channel = pdata->rx_dma_channel;
+ adapter->dma_tx.channel = pdata->tx_dma_channel;
+ } else {
+ adapter->dma_rx.channel = -1;
+ adapter->dma_tx.channel = -1;
+ }
+
+ tasklet_init(&adapter->tasklet, ks8842_tasklet, (unsigned long)netdev);
+ spin_lock_init(&adapter->lock);
+
+ netdev->netdev_ops = &ks8842_netdev_ops;
+ netdev->ethtool_ops = &ks8842_ethtool_ops;
+
+ /* Check if a mac address was given */
+ i = netdev->addr_len;
+ if (pdata) {
+ for (i = 0; i < netdev->addr_len; i++)
+ if (pdata->macaddr[i] != 0)
+ break;
+
+ if (i < netdev->addr_len)
+ /* an address was passed, use it */
+ memcpy(netdev->dev_addr, pdata->macaddr,
+ netdev->addr_len);
+ }
+
+ if (i == netdev->addr_len) {
+ ks8842_read_mac_addr(adapter, netdev->dev_addr);
+
+ if (!is_valid_ether_addr(netdev->dev_addr))
+ random_ether_addr(netdev->dev_addr);
+ }
+
+ id = ks8842_read16(adapter, 32, REG_SW_ID_AND_ENABLE);
+
+ strcpy(netdev->name, "eth%d");
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ platform_set_drvdata(pdev, netdev);
+
+ pr_info("Found chip, family: 0x%x, id: 0x%x, rev: 0x%x\n",
+ (id >> 8) & 0xff, (id >> 4) & 0xf, (id >> 1) & 0x7);
+
+ return 0;
+
+err_register:
+err_get_irq:
+ iounmap(adapter->hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ release_mem_region(iomem->start, resource_size(iomem));
+err_mem_region:
+ return err;
+}
+
+static int __devexit ks8842_remove(struct platform_device *pdev)
+{
+ struct net_device *netdev = platform_get_drvdata(pdev);
+ struct ks8842_adapter *adapter = netdev_priv(netdev);
+ struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ unregister_netdev(netdev);
+ tasklet_kill(&adapter->tasklet);
+ iounmap(adapter->hw_addr);
+ free_netdev(netdev);
+ release_mem_region(iomem->start, resource_size(iomem));
+ platform_set_drvdata(pdev, NULL);
+ return 0;
+}
+
+
+static struct platform_driver ks8842_platform_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = ks8842_probe,
+ .remove = ks8842_remove,
+};
+
+static int __init ks8842_init(void)
+{
+ return platform_driver_register(&ks8842_platform_driver);
+}
+
+static void __exit ks8842_exit(void)
+{
+ platform_driver_unregister(&ks8842_platform_driver);
+}
+
+module_init(ks8842_init);
+module_exit(ks8842_exit);
+
+MODULE_DESCRIPTION("Timberdale KS8842 ethernet driver");
+MODULE_AUTHOR("Mocean Laboratories <info@mocean-labs.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ks8842");
+
--- /dev/null
+/* drivers/net/ks8851.c
+ *
+ * Copyright 2009 Simtec Electronics
+ * http://www.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#define DEBUG
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/cache.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+
+#include <linux/spi/spi.h>
+
+#include "ks8851.h"
+
+/**
+ * struct ks8851_rxctrl - KS8851 driver rx control
+ * @mchash: Multicast hash-table data.
+ * @rxcr1: KS_RXCR1 register setting
+ * @rxcr2: KS_RXCR2 register setting
+ *
+ * Representation of the settings needs to control the receive filtering
+ * such as the multicast hash-filter and the receive register settings. This
+ * is used to make the job of working out if the receive settings change and
+ * then issuing the new settings to the worker that will send the necessary
+ * commands.
+ */
+struct ks8851_rxctrl {
+ u16 mchash[4];
+ u16 rxcr1;
+ u16 rxcr2;
+};
+
+/**
+ * union ks8851_tx_hdr - tx header data
+ * @txb: The header as bytes
+ * @txw: The header as 16bit, little-endian words
+ *
+ * A dual representation of the tx header data to allow
+ * access to individual bytes, and to allow 16bit accesses
+ * with 16bit alignment.
+ */
+union ks8851_tx_hdr {
+ u8 txb[6];
+ __le16 txw[3];
+};
+
+/**
+ * struct ks8851_net - KS8851 driver private data
+ * @netdev: The network device we're bound to
+ * @spidev: The spi device we're bound to.
+ * @lock: Lock to ensure that the device is not accessed when busy.
+ * @statelock: Lock on this structure for tx list.
+ * @mii: The MII state information for the mii calls.
+ * @rxctrl: RX settings for @rxctrl_work.
+ * @tx_work: Work queue for tx packets
+ * @irq_work: Work queue for servicing interrupts
+ * @rxctrl_work: Work queue for updating RX mode and multicast lists
+ * @txq: Queue of packets for transmission.
+ * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1.
+ * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2.
+ * @txh: Space for generating packet TX header in DMA-able data
+ * @rxd: Space for receiving SPI data, in DMA-able space.
+ * @txd: Space for transmitting SPI data, in DMA-able space.
+ * @msg_enable: The message flags controlling driver output (see ethtool).
+ * @fid: Incrementing frame id tag.
+ * @rc_ier: Cached copy of KS_IER.
+ * @rc_ccr: Cached copy of KS_CCR.
+ * @rc_rxqcr: Cached copy of KS_RXQCR.
+ * @eeprom_size: Companion eeprom size in Bytes, 0 if no eeprom
+ *
+ * The @lock ensures that the chip is protected when certain operations are
+ * in progress. When the read or write packet transfer is in progress, most
+ * of the chip registers are not ccessible until the transfer is finished and
+ * the DMA has been de-asserted.
+ *
+ * The @statelock is used to protect information in the structure which may
+ * need to be accessed via several sources, such as the network driver layer
+ * or one of the work queues.
+ *
+ * We align the buffers we may use for rx/tx to ensure that if the SPI driver
+ * wants to DMA map them, it will not have any problems with data the driver
+ * modifies.
+ */
+struct ks8851_net {
+ struct net_device *netdev;
+ struct spi_device *spidev;
+ struct mutex lock;
+ spinlock_t statelock;
+
+ union ks8851_tx_hdr txh ____cacheline_aligned;
+ u8 rxd[8];
+ u8 txd[8];
+
+ u32 msg_enable ____cacheline_aligned;
+ u16 tx_space;
+ u8 fid;
+
+ u16 rc_ier;
+ u16 rc_rxqcr;
+ u16 rc_ccr;
+ u16 eeprom_size;
+
+ struct mii_if_info mii;
+ struct ks8851_rxctrl rxctrl;
+
+ struct work_struct tx_work;
+ struct work_struct irq_work;
+ struct work_struct rxctrl_work;
+
+ struct sk_buff_head txq;
+
+ struct spi_message spi_msg1;
+ struct spi_message spi_msg2;
+ struct spi_transfer spi_xfer1;
+ struct spi_transfer spi_xfer2[2];
+};
+
+static int msg_enable;
+
+/* shift for byte-enable data */
+#define BYTE_EN(_x) ((_x) << 2)
+
+/* turn register number and byte-enable mask into data for start of packet */
+#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg) << (8+2) | (_reg) >> 6)
+
+/* SPI register read/write calls.
+ *
+ * All these calls issue SPI transactions to access the chip's registers. They
+ * all require that the necessary lock is held to prevent accesses when the
+ * chip is busy transferring packet data (RX/TX FIFO accesses).
+ */
+
+/**
+ * ks8851_wrreg16 - write 16bit register value to chip
+ * @ks: The chip state
+ * @reg: The register address
+ * @val: The value to write
+ *
+ * Issue a write to put the value @val into the register specified in @reg.
+ */
+static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val)
+{
+ struct spi_transfer *xfer = &ks->spi_xfer1;
+ struct spi_message *msg = &ks->spi_msg1;
+ __le16 txb[2];
+ int ret;
+
+ txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR);
+ txb[1] = cpu_to_le16(val);
+
+ xfer->tx_buf = txb;
+ xfer->rx_buf = NULL;
+ xfer->len = 4;
+
+ ret = spi_sync(ks->spidev, msg);
+ if (ret < 0)
+ netdev_err(ks->netdev, "spi_sync() failed\n");
+}
+
+/**
+ * ks8851_wrreg8 - write 8bit register value to chip
+ * @ks: The chip state
+ * @reg: The register address
+ * @val: The value to write
+ *
+ * Issue a write to put the value @val into the register specified in @reg.
+ */
+static void ks8851_wrreg8(struct ks8851_net *ks, unsigned reg, unsigned val)
+{
+ struct spi_transfer *xfer = &ks->spi_xfer1;
+ struct spi_message *msg = &ks->spi_msg1;
+ __le16 txb[2];
+ int ret;
+ int bit;
+
+ bit = 1 << (reg & 3);
+
+ txb[0] = cpu_to_le16(MK_OP(bit, reg) | KS_SPIOP_WR);
+ txb[1] = val;
+
+ xfer->tx_buf = txb;
+ xfer->rx_buf = NULL;
+ xfer->len = 3;
+
+ ret = spi_sync(ks->spidev, msg);
+ if (ret < 0)
+ netdev_err(ks->netdev, "spi_sync() failed\n");
+}
+
+/**
+ * ks8851_rx_1msg - select whether to use one or two messages for spi read
+ * @ks: The device structure
+ *
+ * Return whether to generate a single message with a tx and rx buffer
+ * supplied to spi_sync(), or alternatively send the tx and rx buffers
+ * as separate messages.
+ *
+ * Depending on the hardware in use, a single message may be more efficient
+ * on interrupts or work done by the driver.
+ *
+ * This currently always returns true until we add some per-device data passed
+ * from the platform code to specify which mode is better.
+ */
+static inline bool ks8851_rx_1msg(struct ks8851_net *ks)
+{
+ return true;
+}
+
+/**
+ * ks8851_rdreg - issue read register command and return the data
+ * @ks: The device state
+ * @op: The register address and byte enables in message format.
+ * @rxb: The RX buffer to return the result into
+ * @rxl: The length of data expected.
+ *
+ * This is the low level read call that issues the necessary spi message(s)
+ * to read data from the register specified in @op.
+ */
+static void ks8851_rdreg(struct ks8851_net *ks, unsigned op,
+ u8 *rxb, unsigned rxl)
+{
+ struct spi_transfer *xfer;
+ struct spi_message *msg;
+ __le16 *txb = (__le16 *)ks->txd;
+ u8 *trx = ks->rxd;
+ int ret;
+
+ txb[0] = cpu_to_le16(op | KS_SPIOP_RD);
+
+ if (ks8851_rx_1msg(ks)) {
+ msg = &ks->spi_msg1;
+ xfer = &ks->spi_xfer1;
+
+ xfer->tx_buf = txb;
+ xfer->rx_buf = trx;
+ xfer->len = rxl + 2;
+ } else {
+ msg = &ks->spi_msg2;
+ xfer = ks->spi_xfer2;
+
+ xfer->tx_buf = txb;
+ xfer->rx_buf = NULL;
+ xfer->len = 2;
+
+ xfer++;
+ xfer->tx_buf = NULL;
+ xfer->rx_buf = trx;
+ xfer->len = rxl;
+ }
+
+ ret = spi_sync(ks->spidev, msg);
+ if (ret < 0)
+ netdev_err(ks->netdev, "read: spi_sync() failed\n");
+ else if (ks8851_rx_1msg(ks))
+ memcpy(rxb, trx + 2, rxl);
+ else
+ memcpy(rxb, trx, rxl);
+}
+
+/**
+ * ks8851_rdreg8 - read 8 bit register from device
+ * @ks: The chip information
+ * @reg: The register address
+ *
+ * Read a 8bit register from the chip, returning the result
+*/
+static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg)
+{
+ u8 rxb[1];
+
+ ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1);
+ return rxb[0];
+}
+
+/**
+ * ks8851_rdreg16 - read 16 bit register from device
+ * @ks: The chip information
+ * @reg: The register address
+ *
+ * Read a 16bit register from the chip, returning the result
+*/
+static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg)
+{
+ __le16 rx = 0;
+
+ ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2);
+ return le16_to_cpu(rx);
+}
+
+/**
+ * ks8851_rdreg32 - read 32 bit register from device
+ * @ks: The chip information
+ * @reg: The register address
+ *
+ * Read a 32bit register from the chip.
+ *
+ * Note, this read requires the address be aligned to 4 bytes.
+*/
+static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg)
+{
+ __le32 rx = 0;
+
+ WARN_ON(reg & 3);
+
+ ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4);
+ return le32_to_cpu(rx);
+}
+
+/**
+ * ks8851_soft_reset - issue one of the soft reset to the device
+ * @ks: The device state.
+ * @op: The bit(s) to set in the GRR
+ *
+ * Issue the relevant soft-reset command to the device's GRR register
+ * specified by @op.
+ *
+ * Note, the delays are in there as a caution to ensure that the reset
+ * has time to take effect and then complete. Since the datasheet does
+ * not currently specify the exact sequence, we have chosen something
+ * that seems to work with our device.
+ */
+static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op)
+{
+ ks8851_wrreg16(ks, KS_GRR, op);
+ mdelay(1); /* wait a short time to effect reset */
+ ks8851_wrreg16(ks, KS_GRR, 0);
+ mdelay(1); /* wait for condition to clear */
+}
+
+/**
+ * ks8851_write_mac_addr - write mac address to device registers
+ * @dev: The network device
+ *
+ * Update the KS8851 MAC address registers from the address in @dev.
+ *
+ * This call assumes that the chip is not running, so there is no need to
+ * shutdown the RXQ process whilst setting this.
+*/
+static int ks8851_write_mac_addr(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ int i;
+
+ mutex_lock(&ks->lock);
+
+ for (i = 0; i < ETH_ALEN; i++)
+ ks8851_wrreg8(ks, KS_MAR(i), dev->dev_addr[i]);
+
+ mutex_unlock(&ks->lock);
+
+ return 0;
+}
+
+/**
+ * ks8851_init_mac - initialise the mac address
+ * @ks: The device structure
+ *
+ * Get or create the initial mac address for the device and then set that
+ * into the station address register. Currently we assume that the device
+ * does not have a valid mac address in it, and so we use random_ether_addr()
+ * to create a new one.
+ *
+ * In future, the driver should check to see if the device has an EEPROM
+ * attached and whether that has a valid ethernet address in it.
+ */
+static void ks8851_init_mac(struct ks8851_net *ks)
+{
+ struct net_device *dev = ks->netdev;
+
+ random_ether_addr(dev->dev_addr);
+ ks8851_write_mac_addr(dev);
+}
+
+/**
+ * ks8851_irq - device interrupt handler
+ * @irq: Interrupt number passed from the IRQ hnalder.
+ * @pw: The private word passed to register_irq(), our struct ks8851_net.
+ *
+ * Disable the interrupt from happening again until we've processed the
+ * current status by scheduling ks8851_irq_work().
+ */
+static irqreturn_t ks8851_irq(int irq, void *pw)
+{
+ struct ks8851_net *ks = pw;
+
+ disable_irq_nosync(irq);
+ schedule_work(&ks->irq_work);
+ return IRQ_HANDLED;
+}
+
+/**
+ * ks8851_rdfifo - read data from the receive fifo
+ * @ks: The device state.
+ * @buff: The buffer address
+ * @len: The length of the data to read
+ *
+ * Issue an RXQ FIFO read command and read the @len amount of data from
+ * the FIFO into the buffer specified by @buff.
+ */
+static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len)
+{
+ struct spi_transfer *xfer = ks->spi_xfer2;
+ struct spi_message *msg = &ks->spi_msg2;
+ u8 txb[1];
+ int ret;
+
+ netif_dbg(ks, rx_status, ks->netdev,
+ "%s: %d@%p\n", __func__, len, buff);
+
+ /* set the operation we're issuing */
+ txb[0] = KS_SPIOP_RXFIFO;
+
+ xfer->tx_buf = txb;
+ xfer->rx_buf = NULL;
+ xfer->len = 1;
+
+ xfer++;
+ xfer->rx_buf = buff;
+ xfer->tx_buf = NULL;
+ xfer->len = len;
+
+ ret = spi_sync(ks->spidev, msg);
+ if (ret < 0)
+ netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__);
+}
+
+/**
+ * ks8851_dbg_dumpkkt - dump initial packet contents to debug
+ * @ks: The device state
+ * @rxpkt: The data for the received packet
+ *
+ * Dump the initial data from the packet to dev_dbg().
+*/
+static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt)
+{
+ netdev_dbg(ks->netdev,
+ "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n",
+ rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7],
+ rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11],
+ rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]);
+}
+
+/**
+ * ks8851_rx_pkts - receive packets from the host
+ * @ks: The device information.
+ *
+ * This is called from the IRQ work queue when the system detects that there
+ * are packets in the receive queue. Find out how many packets there are and
+ * read them from the FIFO.
+ */
+static void ks8851_rx_pkts(struct ks8851_net *ks)
+{
+ struct sk_buff *skb;
+ unsigned rxfc;
+ unsigned rxlen;
+ unsigned rxstat;
+ u32 rxh;
+ u8 *rxpkt;
+
+ rxfc = ks8851_rdreg8(ks, KS_RXFC);
+
+ netif_dbg(ks, rx_status, ks->netdev,
+ "%s: %d packets\n", __func__, rxfc);
+
+ /* Currently we're issuing a read per packet, but we could possibly
+ * improve the code by issuing a single read, getting the receive
+ * header, allocating the packet and then reading the packet data
+ * out in one go.
+ *
+ * This form of operation would require us to hold the SPI bus'
+ * chipselect low during the entie transaction to avoid any
+ * reset to the data stream coming from the chip.
+ */
+
+ for (; rxfc != 0; rxfc--) {
+ rxh = ks8851_rdreg32(ks, KS_RXFHSR);
+ rxstat = rxh & 0xffff;
+ rxlen = rxh >> 16;
+
+ netif_dbg(ks, rx_status, ks->netdev,
+ "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen);
+
+ /* the length of the packet includes the 32bit CRC */
+
+ /* set dma read address */
+ ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00);
+
+ /* start the packet dma process, and set auto-dequeue rx */
+ ks8851_wrreg16(ks, KS_RXQCR,
+ ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE);
+
+ if (rxlen > 4) {
+ unsigned int rxalign;
+
+ rxlen -= 4;
+ rxalign = ALIGN(rxlen, 4);
+ skb = netdev_alloc_skb_ip_align(ks->netdev, rxalign);
+ if (skb) {
+
+ /* 4 bytes of status header + 4 bytes of
+ * garbage: we put them before ethernet
+ * header, so that they are copied,
+ * but ignored.
+ */
+
+ rxpkt = skb_put(skb, rxlen) - 8;
+
+ ks8851_rdfifo(ks, rxpkt, rxalign + 8);
+
+ if (netif_msg_pktdata(ks))
+ ks8851_dbg_dumpkkt(ks, rxpkt);
+
+ skb->protocol = eth_type_trans(skb, ks->netdev);
+ netif_rx(skb);
+
+ ks->netdev->stats.rx_packets++;
+ ks->netdev->stats.rx_bytes += rxlen;
+ }
+ }
+
+ ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+ }
+}
+
+/**
+ * ks8851_irq_work - work queue handler for dealing with interrupt requests
+ * @work: The work structure that was scheduled by schedule_work()
+ *
+ * This is the handler invoked when the ks8851_irq() is called to find out
+ * what happened, as we cannot allow ourselves to sleep whilst waiting for
+ * anything other process has the chip's lock.
+ *
+ * Read the interrupt status, work out what needs to be done and then clear
+ * any of the interrupts that are not needed.
+ */
+static void ks8851_irq_work(struct work_struct *work)
+{
+ struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work);
+ unsigned status;
+ unsigned handled = 0;
+
+ mutex_lock(&ks->lock);
+
+ status = ks8851_rdreg16(ks, KS_ISR);
+
+ netif_dbg(ks, intr, ks->netdev,
+ "%s: status 0x%04x\n", __func__, status);
+
+ if (status & IRQ_LCI) {
+ /* should do something about checking link status */
+ handled |= IRQ_LCI;
+ }
+
+ if (status & IRQ_LDI) {
+ u16 pmecr = ks8851_rdreg16(ks, KS_PMECR);
+ pmecr &= ~PMECR_WKEVT_MASK;
+ ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);
+
+ handled |= IRQ_LDI;
+ }
+
+ if (status & IRQ_RXPSI)
+ handled |= IRQ_RXPSI;
+
+ if (status & IRQ_TXI) {
+ handled |= IRQ_TXI;
+
+ /* no lock here, tx queue should have been stopped */
+
+ /* update our idea of how much tx space is available to the
+ * system */
+ ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR);
+
+ netif_dbg(ks, intr, ks->netdev,
+ "%s: txspace %d\n", __func__, ks->tx_space);
+ }
+
+ if (status & IRQ_RXI)
+ handled |= IRQ_RXI;
+
+ if (status & IRQ_SPIBEI) {
+ dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__);
+ handled |= IRQ_SPIBEI;
+ }
+
+ ks8851_wrreg16(ks, KS_ISR, handled);
+
+ if (status & IRQ_RXI) {
+ /* the datasheet says to disable the rx interrupt during
+ * packet read-out, however we're masking the interrupt
+ * from the device so do not bother masking just the RX
+ * from the device. */
+
+ ks8851_rx_pkts(ks);
+ }
+
+ /* if something stopped the rx process, probably due to wanting
+ * to change the rx settings, then do something about restarting
+ * it. */
+ if (status & IRQ_RXPSI) {
+ struct ks8851_rxctrl *rxc = &ks->rxctrl;
+
+ /* update the multicast hash table */
+ ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]);
+ ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]);
+ ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]);
+ ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]);
+
+ ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2);
+ ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1);
+ }
+
+ mutex_unlock(&ks->lock);
+
+ if (status & IRQ_TXI)
+ netif_wake_queue(ks->netdev);
+
+ enable_irq(ks->netdev->irq);
+}
+
+/**
+ * calc_txlen - calculate size of message to send packet
+ * @len: Length of data
+ *
+ * Returns the size of the TXFIFO message needed to send
+ * this packet.
+ */
+static inline unsigned calc_txlen(unsigned len)
+{
+ return ALIGN(len + 4, 4);
+}
+
+/**
+ * ks8851_wrpkt - write packet to TX FIFO
+ * @ks: The device state.
+ * @txp: The sk_buff to transmit.
+ * @irq: IRQ on completion of the packet.
+ *
+ * Send the @txp to the chip. This means creating the relevant packet header
+ * specifying the length of the packet and the other information the chip
+ * needs, such as IRQ on completion. Send the header and the packet data to
+ * the device.
+ */
+static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq)
+{
+ struct spi_transfer *xfer = ks->spi_xfer2;
+ struct spi_message *msg = &ks->spi_msg2;
+ unsigned fid = 0;
+ int ret;
+
+ netif_dbg(ks, tx_queued, ks->netdev, "%s: skb %p, %d@%p, irq %d\n",
+ __func__, txp, txp->len, txp->data, irq);
+
+ fid = ks->fid++;
+ fid &= TXFR_TXFID_MASK;
+
+ if (irq)
+ fid |= TXFR_TXIC; /* irq on completion */
+
+ /* start header at txb[1] to align txw entries */
+ ks->txh.txb[1] = KS_SPIOP_TXFIFO;
+ ks->txh.txw[1] = cpu_to_le16(fid);
+ ks->txh.txw[2] = cpu_to_le16(txp->len);
+
+ xfer->tx_buf = &ks->txh.txb[1];
+ xfer->rx_buf = NULL;
+ xfer->len = 5;
+
+ xfer++;
+ xfer->tx_buf = txp->data;
+ xfer->rx_buf = NULL;
+ xfer->len = ALIGN(txp->len, 4);
+
+ ret = spi_sync(ks->spidev, msg);
+ if (ret < 0)
+ netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__);
+}
+
+/**
+ * ks8851_done_tx - update and then free skbuff after transmitting
+ * @ks: The device state
+ * @txb: The buffer transmitted
+ */
+static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb)
+{
+ struct net_device *dev = ks->netdev;
+
+ dev->stats.tx_bytes += txb->len;
+ dev->stats.tx_packets++;
+
+ dev_kfree_skb(txb);
+}
+
+/**
+ * ks8851_tx_work - process tx packet(s)
+ * @work: The work strucutre what was scheduled.
+ *
+ * This is called when a number of packets have been scheduled for
+ * transmission and need to be sent to the device.
+ */
+static void ks8851_tx_work(struct work_struct *work)
+{
+ struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work);
+ struct sk_buff *txb;
+ bool last = skb_queue_empty(&ks->txq);
+
+ mutex_lock(&ks->lock);
+
+ while (!last) {
+ txb = skb_dequeue(&ks->txq);
+ last = skb_queue_empty(&ks->txq);
+
+ if (txb != NULL) {
+ ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
+ ks8851_wrpkt(ks, txb, last);
+ ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+ ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
+
+ ks8851_done_tx(ks, txb);
+ }
+ }
+
+ mutex_unlock(&ks->lock);
+}
+
+/**
+ * ks8851_set_powermode - set power mode of the device
+ * @ks: The device state
+ * @pwrmode: The power mode value to write to KS_PMECR.
+ *
+ * Change the power mode of the chip.
+ */
+static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode)
+{
+ unsigned pmecr;
+
+ netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode);
+
+ pmecr = ks8851_rdreg16(ks, KS_PMECR);
+ pmecr &= ~PMECR_PM_MASK;
+ pmecr |= pwrmode;
+
+ ks8851_wrreg16(ks, KS_PMECR, pmecr);
+}
+
+/**
+ * ks8851_net_open - open network device
+ * @dev: The network device being opened.
+ *
+ * Called when the network device is marked active, such as a user executing
+ * 'ifconfig up' on the device.
+ */
+static int ks8851_net_open(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+
+ /* lock the card, even if we may not actually be doing anything
+ * else at the moment */
+ mutex_lock(&ks->lock);
+
+ netif_dbg(ks, ifup, ks->netdev, "opening\n");
+
+ /* bring chip out of any power saving mode it was in */
+ ks8851_set_powermode(ks, PMECR_PM_NORMAL);
+
+ /* issue a soft reset to the RX/TX QMU to put it into a known
+ * state. */
+ ks8851_soft_reset(ks, GRR_QMU);
+
+ /* setup transmission parameters */
+
+ ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */
+ TXCR_TXPE | /* pad to min length */
+ TXCR_TXCRC | /* add CRC */
+ TXCR_TXFCE)); /* enable flow control */
+
+ /* auto-increment tx data, reset tx pointer */
+ ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);
+
+ /* setup receiver control */
+
+ ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */
+ RXCR1_RXFCE | /* enable flow control */
+ RXCR1_RXBE | /* broadcast enable */
+ RXCR1_RXUE | /* unicast enable */
+ RXCR1_RXE)); /* enable rx block */
+
+ /* transfer entire frames out in one go */
+ ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME);
+
+ /* set receive counter timeouts */
+ ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */
+ ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */
+ ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */
+
+ ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */
+ RXQCR_RXDBCTE | /* IRQ on byte count exceeded */
+ RXQCR_RXDTTE); /* IRQ on time exceeded */
+
+ ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+
+ /* clear then enable interrupts */
+
+#define STD_IRQ (IRQ_LCI | /* Link Change */ \
+ IRQ_TXI | /* TX done */ \
+ IRQ_RXI | /* RX done */ \
+ IRQ_SPIBEI | /* SPI bus error */ \
+ IRQ_TXPSI | /* TX process stop */ \
+ IRQ_RXPSI) /* RX process stop */
+
+ ks->rc_ier = STD_IRQ;
+ ks8851_wrreg16(ks, KS_ISR, STD_IRQ);
+ ks8851_wrreg16(ks, KS_IER, STD_IRQ);
+
+ netif_start_queue(ks->netdev);
+
+ netif_dbg(ks, ifup, ks->netdev, "network device up\n");
+
+ mutex_unlock(&ks->lock);
+ return 0;
+}
+
+/**
+ * ks8851_net_stop - close network device
+ * @dev: The device being closed.
+ *
+ * Called to close down a network device which has been active. Cancell any
+ * work, shutdown the RX and TX process and then place the chip into a low
+ * power state whilst it is not being used.
+ */
+static int ks8851_net_stop(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+
+ netif_info(ks, ifdown, dev, "shutting down\n");
+
+ netif_stop_queue(dev);
+
+ mutex_lock(&ks->lock);
+
+ /* stop any outstanding work */
+ flush_work(&ks->irq_work);
+ flush_work(&ks->tx_work);
+ flush_work(&ks->rxctrl_work);
+
+ /* turn off the IRQs and ack any outstanding */
+ ks8851_wrreg16(ks, KS_IER, 0x0000);
+ ks8851_wrreg16(ks, KS_ISR, 0xffff);
+
+ /* shutdown RX process */
+ ks8851_wrreg16(ks, KS_RXCR1, 0x0000);
+
+ /* shutdown TX process */
+ ks8851_wrreg16(ks, KS_TXCR, 0x0000);
+
+ /* set powermode to soft power down to save power */
+ ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN);
+
+ /* ensure any queued tx buffers are dumped */
+ while (!skb_queue_empty(&ks->txq)) {
+ struct sk_buff *txb = skb_dequeue(&ks->txq);
+
+ netif_dbg(ks, ifdown, ks->netdev,
+ "%s: freeing txb %p\n", __func__, txb);
+
+ dev_kfree_skb(txb);
+ }
+
+ mutex_unlock(&ks->lock);
+ return 0;
+}
+
+/**
+ * ks8851_start_xmit - transmit packet
+ * @skb: The buffer to transmit
+ * @dev: The device used to transmit the packet.
+ *
+ * Called by the network layer to transmit the @skb. Queue the packet for
+ * the device and schedule the necessary work to transmit the packet when
+ * it is free.
+ *
+ * We do this to firstly avoid sleeping with the network device locked,
+ * and secondly so we can round up more than one packet to transmit which
+ * means we can try and avoid generating too many transmit done interrupts.
+ */
+static netdev_tx_t ks8851_start_xmit(struct sk_buff *skb,
+ struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ unsigned needed = calc_txlen(skb->len);
+ netdev_tx_t ret = NETDEV_TX_OK;
+
+ netif_dbg(ks, tx_queued, ks->netdev,
+ "%s: skb %p, %d@%p\n", __func__, skb, skb->len, skb->data);
+
+ spin_lock(&ks->statelock);
+
+ if (needed > ks->tx_space) {
+ netif_stop_queue(dev);
+ ret = NETDEV_TX_BUSY;
+ } else {
+ ks->tx_space -= needed;
+ skb_queue_tail(&ks->txq, skb);
+ }
+
+ spin_unlock(&ks->statelock);
+ schedule_work(&ks->tx_work);
+
+ return ret;
+}
+
+/**
+ * ks8851_rxctrl_work - work handler to change rx mode
+ * @work: The work structure this belongs to.
+ *
+ * Lock the device and issue the necessary changes to the receive mode from
+ * the network device layer. This is done so that we can do this without
+ * having to sleep whilst holding the network device lock.
+ *
+ * Since the recommendation from Micrel is that the RXQ is shutdown whilst the
+ * receive parameters are programmed, we issue a write to disable the RXQ and
+ * then wait for the interrupt handler to be triggered once the RXQ shutdown is
+ * complete. The interrupt handler then writes the new values into the chip.
+ */
+static void ks8851_rxctrl_work(struct work_struct *work)
+{
+ struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work);
+
+ mutex_lock(&ks->lock);
+
+ /* need to shutdown RXQ before modifying filter parameters */
+ ks8851_wrreg16(ks, KS_RXCR1, 0x00);
+
+ mutex_unlock(&ks->lock);
+}
+
+static void ks8851_set_rx_mode(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ struct ks8851_rxctrl rxctrl;
+
+ memset(&rxctrl, 0, sizeof(rxctrl));
+
+ if (dev->flags & IFF_PROMISC) {
+ /* interface to receive everything */
+
+ rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF;
+ } else if (dev->flags & IFF_ALLMULTI) {
+ /* accept all multicast packets */
+
+ rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE |
+ RXCR1_RXPAFMA | RXCR1_RXMAFMA);
+ } else if (dev->flags & IFF_MULTICAST && !netdev_mc_empty(dev)) {
+ struct netdev_hw_addr *ha;
+ u32 crc;
+
+ /* accept some multicast */
+
+ netdev_for_each_mc_addr(ha, dev) {
+ crc = ether_crc(ETH_ALEN, ha->addr);
+ crc >>= (32 - 6); /* get top six bits */
+
+ rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf));
+ }
+
+ rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXPAFMA;
+ } else {
+ /* just accept broadcast / unicast */
+ rxctrl.rxcr1 = RXCR1_RXPAFMA;
+ }
+
+ rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */
+ RXCR1_RXBE | /* broadcast enable */
+ RXCR1_RXE | /* RX process enable */
+ RXCR1_RXFCE); /* enable flow control */
+
+ rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME;
+
+ /* schedule work to do the actual set of the data if needed */
+
+ spin_lock(&ks->statelock);
+
+ if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) {
+ memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl));
+ schedule_work(&ks->rxctrl_work);
+ }
+
+ spin_unlock(&ks->statelock);
+}
+
+static int ks8851_set_mac_address(struct net_device *dev, void *addr)
+{
+ struct sockaddr *sa = addr;
+
+ if (netif_running(dev))
+ return -EBUSY;
+
+ if (!is_valid_ether_addr(sa->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN);
+ return ks8851_write_mac_addr(dev);
+}
+
+static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+
+ if (!netif_running(dev))
+ return -EINVAL;
+
+ return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
+}
+
+static const struct net_device_ops ks8851_netdev_ops = {
+ .ndo_open = ks8851_net_open,
+ .ndo_stop = ks8851_net_stop,
+ .ndo_do_ioctl = ks8851_net_ioctl,
+ .ndo_start_xmit = ks8851_start_xmit,
+ .ndo_set_mac_address = ks8851_set_mac_address,
+ .ndo_set_rx_mode = ks8851_set_rx_mode,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
+/* Companion eeprom access */
+
+enum { /* EEPROM programming states */
+ EEPROM_CONTROL,
+ EEPROM_ADDRESS,
+ EEPROM_DATA,
+ EEPROM_COMPLETE
+};
+
+/**
+ * ks8851_eeprom_read - read a 16bits word in ks8851 companion EEPROM
+ * @dev: The network device the PHY is on.
+ * @addr: EEPROM address to read
+ *
+ * eeprom_size: used to define the data coding length. Can be changed
+ * through debug-fs.
+ *
+ * Programs a read on the EEPROM using ks8851 EEPROM SW access feature.
+ * Warning: The READ feature is not supported on ks8851 revision 0.
+ *
+ * Rough programming model:
+ * - on period start: set clock high and read value on bus
+ * - on period / 2: set clock low and program value on bus
+ * - start on period / 2
+ */
+unsigned int ks8851_eeprom_read(struct net_device *dev, unsigned int addr)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ int eepcr;
+ int ctrl = EEPROM_OP_READ;
+ int state = EEPROM_CONTROL;
+ int bit_count = EEPROM_OP_LEN - 1;
+ unsigned int data = 0;
+ int dummy;
+ unsigned int addr_len;
+
+ addr_len = (ks->eeprom_size == 128) ? 6 : 8;
+
+ /* start transaction: chip select high, authorize write */
+ mutex_lock(&ks->lock);
+ eepcr = EEPCR_EESA | EEPCR_EESRWA;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ eepcr |= EEPCR_EECS;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ while (state != EEPROM_COMPLETE) {
+ /* falling clock period starts... */
+ /* set EED_IO pin for control and address */
+ eepcr &= ~EEPCR_EEDO;
+ switch (state) {
+ case EEPROM_CONTROL:
+ eepcr |= ((ctrl >> bit_count) & 1) << 2;
+ if (bit_count-- <= 0) {
+ bit_count = addr_len - 1;
+ state = EEPROM_ADDRESS;
+ }
+ break;
+ case EEPROM_ADDRESS:
+ eepcr |= ((addr >> bit_count) & 1) << 2;
+ bit_count--;
+ break;
+ case EEPROM_DATA:
+ /* Change to receive mode */
+ eepcr &= ~EEPCR_EESRWA;
+ break;
+ }
+
+ /* lower clock */
+ eepcr &= ~EEPCR_EESCK;
+
+ mutex_lock(&ks->lock);
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ /* waitread period / 2 */
+ udelay(EEPROM_SK_PERIOD / 2);
+
+ /* rising clock period starts... */
+
+ /* raise clock */
+ mutex_lock(&ks->lock);
+ eepcr |= EEPCR_EESCK;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ /* Manage read */
+ switch (state) {
+ case EEPROM_ADDRESS:
+ if (bit_count < 0) {
+ bit_count = EEPROM_DATA_LEN - 1;
+ state = EEPROM_DATA;
+ }
+ break;
+ case EEPROM_DATA:
+ mutex_lock(&ks->lock);
+ dummy = ks8851_rdreg16(ks, KS_EEPCR);
+ mutex_unlock(&ks->lock);
+ data |= ((dummy >> EEPCR_EESB_OFFSET) & 1) << bit_count;
+ if (bit_count-- <= 0)
+ state = EEPROM_COMPLETE;
+ break;
+ }
+
+ /* wait period / 2 */
+ udelay(EEPROM_SK_PERIOD / 2);
+ }
+
+ /* close transaction */
+ mutex_lock(&ks->lock);
+ eepcr &= ~EEPCR_EECS;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ eepcr = 0;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ return data;
+}
+
+/**
+ * ks8851_eeprom_write - write a 16bits word in ks8851 companion EEPROM
+ * @dev: The network device the PHY is on.
+ * @op: operand (can be WRITE, EWEN, EWDS)
+ * @addr: EEPROM address to write
+ * @data: data to write
+ *
+ * eeprom_size: used to define the data coding length. Can be changed
+ * through debug-fs.
+ *
+ * Programs a write on the EEPROM using ks8851 EEPROM SW access feature.
+ *
+ * Note that a write enable is required before writing data.
+ *
+ * Rough programming model:
+ * - on period start: set clock high
+ * - on period / 2: set clock low and program value on bus
+ * - start on period / 2
+ */
+void ks8851_eeprom_write(struct net_device *dev, unsigned int op,
+ unsigned int addr, unsigned int data)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ int eepcr;
+ int state = EEPROM_CONTROL;
+ int bit_count = EEPROM_OP_LEN - 1;
+ unsigned int addr_len;
+
+ addr_len = (ks->eeprom_size == 128) ? 6 : 8;
+
+ switch (op) {
+ case EEPROM_OP_EWEN:
+ addr = 0x30;
+ break;
+ case EEPROM_OP_EWDS:
+ addr = 0;
+ break;
+ }
+
+ /* start transaction: chip select high, authorize write */
+ mutex_lock(&ks->lock);
+ eepcr = EEPCR_EESA | EEPCR_EESRWA;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ eepcr |= EEPCR_EECS;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ while (state != EEPROM_COMPLETE) {
+ /* falling clock period starts... */
+ /* set EED_IO pin for control and address */
+ eepcr &= ~EEPCR_EEDO;
+ switch (state) {
+ case EEPROM_CONTROL:
+ eepcr |= ((op >> bit_count) & 1) << 2;
+ if (bit_count-- <= 0) {
+ bit_count = addr_len - 1;
+ state = EEPROM_ADDRESS;
+ }
+ break;
+ case EEPROM_ADDRESS:
+ eepcr |= ((addr >> bit_count) & 1) << 2;
+ if (bit_count-- <= 0) {
+ if (op == EEPROM_OP_WRITE) {
+ bit_count = EEPROM_DATA_LEN - 1;
+ state = EEPROM_DATA;
+ } else {
+ state = EEPROM_COMPLETE;
+ }
+ }
+ break;
+ case EEPROM_DATA:
+ eepcr |= ((data >> bit_count) & 1) << 2;
+ if (bit_count-- <= 0)
+ state = EEPROM_COMPLETE;
+ break;
+ }
+
+ /* lower clock */
+ eepcr &= ~EEPCR_EESCK;
+
+ mutex_lock(&ks->lock);
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ /* wait period / 2 */
+ udelay(EEPROM_SK_PERIOD / 2);
+
+ /* rising clock period starts... */
+
+ /* raise clock */
+ eepcr |= EEPCR_EESCK;
+ mutex_lock(&ks->lock);
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+ /* wait period / 2 */
+ udelay(EEPROM_SK_PERIOD / 2);
+ }
+
+ /* close transaction */
+ mutex_lock(&ks->lock);
+ eepcr &= ~EEPCR_EECS;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ eepcr = 0;
+ ks8851_wrreg16(ks, KS_EEPCR, eepcr);
+ mutex_unlock(&ks->lock);
+
+}
+
+/* ethtool support */
+
+static void ks8851_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *di)
+{
+ strlcpy(di->driver, "KS8851", sizeof(di->driver));
+ strlcpy(di->version, "1.00", sizeof(di->version));
+ strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info));
+}
+
+static u32 ks8851_get_msglevel(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ return ks->msg_enable;
+}
+
+static void ks8851_set_msglevel(struct net_device *dev, u32 to)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ ks->msg_enable = to;
+}
+
+static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ return mii_ethtool_gset(&ks->mii, cmd);
+}
+
+static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ return mii_ethtool_sset(&ks->mii, cmd);
+}
+
+static u32 ks8851_get_link(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ return mii_link_ok(&ks->mii);
+}
+
+static int ks8851_nway_reset(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ return mii_nway_restart(&ks->mii);
+}
+
+static int ks8851_get_eeprom_len(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ return ks->eeprom_size;
+}
+
+static int ks8851_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ u16 *eeprom_buff;
+ int first_word;
+ int last_word;
+ int ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EINVAL;
+
+ if (eeprom->len > ks->eeprom_size)
+ return -EINVAL;
+
+ eeprom->magic = ks8851_rdreg16(ks, KS_CIDER);
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+
+ eeprom_buff = kmalloc(sizeof(u16) *
+ (last_word - first_word + 1), GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ for (i = 0; i < last_word - first_word + 1; i++)
+ eeprom_buff[i] = ks8851_eeprom_read(dev, first_word + 1);
+
+ /* Device's eeprom is little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1), eeprom->len);
+ kfree(eeprom_buff);
+
+ return ret_val;
+}
+
+static int ks8851_set_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ u16 *eeprom_buff;
+ void *ptr;
+ int max_len;
+ int first_word;
+ int last_word;
+ int ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EOPNOTSUPP;
+
+ if (eeprom->len > ks->eeprom_size)
+ return -EINVAL;
+
+ if (eeprom->magic != ks8851_rdreg16(ks, KS_CIDER))
+ return -EFAULT;
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+ max_len = (last_word - first_word + 1) * 2;
+ eeprom_buff = kmalloc(max_len, GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ ptr = (void *)eeprom_buff;
+
+ if (eeprom->offset & 1) {
+ /* need read/modify/write of first changed EEPROM word */
+ /* only the second byte of the word is being modified */
+ eeprom_buff[0] = ks8851_eeprom_read(dev, first_word);
+ ptr++;
+ }
+ if ((eeprom->offset + eeprom->len) & 1)
+ /* need read/modify/write of last changed EEPROM word */
+ /* only the first byte of the word is being modified */
+ eeprom_buff[last_word - first_word] =
+ ks8851_eeprom_read(dev, last_word);
+
+
+ /* Device's eeprom is little-endian, word addressable */
+ le16_to_cpus(&eeprom_buff[0]);
+ le16_to_cpus(&eeprom_buff[last_word - first_word]);
+
+ memcpy(ptr, bytes, eeprom->len);
+
+ for (i = 0; i < last_word - first_word + 1; i++)
+ eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
+
+ ks8851_eeprom_write(dev, EEPROM_OP_EWEN, 0, 0);
+
+ for (i = 0; i < last_word - first_word + 1; i++) {
+ ks8851_eeprom_write(dev, EEPROM_OP_WRITE, first_word + i,
+ eeprom_buff[i]);
+ mdelay(EEPROM_WRITE_TIME);
+ }
+
+ ks8851_eeprom_write(dev, EEPROM_OP_EWDS, 0, 0);
+
+ kfree(eeprom_buff);
+ return ret_val;
+}
+
+static const struct ethtool_ops ks8851_ethtool_ops = {
+ .get_drvinfo = ks8851_get_drvinfo,
+ .get_msglevel = ks8851_get_msglevel,
+ .set_msglevel = ks8851_set_msglevel,
+ .get_settings = ks8851_get_settings,
+ .set_settings = ks8851_set_settings,
+ .get_link = ks8851_get_link,
+ .nway_reset = ks8851_nway_reset,
+ .get_eeprom_len = ks8851_get_eeprom_len,
+ .get_eeprom = ks8851_get_eeprom,
+ .set_eeprom = ks8851_set_eeprom,
+};
+
+/* MII interface controls */
+
+/**
+ * ks8851_phy_reg - convert MII register into a KS8851 register
+ * @reg: MII register number.
+ *
+ * Return the KS8851 register number for the corresponding MII PHY register
+ * if possible. Return zero if the MII register has no direct mapping to the
+ * KS8851 register set.
+ */
+static int ks8851_phy_reg(int reg)
+{
+ switch (reg) {
+ case MII_BMCR:
+ return KS_P1MBCR;
+ case MII_BMSR:
+ return KS_P1MBSR;
+ case MII_PHYSID1:
+ return KS_PHY1ILR;
+ case MII_PHYSID2:
+ return KS_PHY1IHR;
+ case MII_ADVERTISE:
+ return KS_P1ANAR;
+ case MII_LPA:
+ return KS_P1ANLPR;
+ }
+
+ return 0x0;
+}
+
+/**
+ * ks8851_phy_read - MII interface PHY register read.
+ * @dev: The network device the PHY is on.
+ * @phy_addr: Address of PHY (ignored as we only have one)
+ * @reg: The register to read.
+ *
+ * This call reads data from the PHY register specified in @reg. Since the
+ * device does not support all the MII registers, the non-existent values
+ * are always returned as zero.
+ *
+ * We return zero for unsupported registers as the MII code does not check
+ * the value returned for any error status, and simply returns it to the
+ * caller. The mii-tool that the driver was tested with takes any -ve error
+ * as real PHY capabilities, thus displaying incorrect data to the user.
+ */
+static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ int ksreg;
+ int result;
+
+ ksreg = ks8851_phy_reg(reg);
+ if (!ksreg)
+ return 0x0; /* no error return allowed, so use zero */
+
+ mutex_lock(&ks->lock);
+ result = ks8851_rdreg16(ks, ksreg);
+ mutex_unlock(&ks->lock);
+
+ return result;
+}
+
+static void ks8851_phy_write(struct net_device *dev,
+ int phy, int reg, int value)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ int ksreg;
+
+ ksreg = ks8851_phy_reg(reg);
+ if (ksreg) {
+ mutex_lock(&ks->lock);
+ ks8851_wrreg16(ks, ksreg, value);
+ mutex_unlock(&ks->lock);
+ }
+}
+
+/**
+ * ks8851_read_selftest - read the selftest memory info.
+ * @ks: The device state
+ *
+ * Read and check the TX/RX memory selftest information.
+ */
+static int ks8851_read_selftest(struct ks8851_net *ks)
+{
+ unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
+ int ret = 0;
+ unsigned rd;
+
+ rd = ks8851_rdreg16(ks, KS_MBIR);
+
+ if ((rd & both_done) != both_done) {
+ netdev_warn(ks->netdev, "Memory selftest not finished\n");
+ return 0;
+ }
+
+ if (rd & MBIR_TXMBFA) {
+ netdev_err(ks->netdev, "TX memory selftest fail\n");
+ ret |= 1;
+ }
+
+ if (rd & MBIR_RXMBFA) {
+ netdev_err(ks->netdev, "RX memory selftest fail\n");
+ ret |= 2;
+ }
+
+ return 0;
+}
+
+/* driver bus management functions */
+
+#ifdef CONFIG_PM
+static int ks8851_suspend(struct spi_device *spi, pm_message_t state)
+{
+ struct ks8851_net *ks = dev_get_drvdata(&spi->dev);
+ struct net_device *dev = ks->netdev;
+
+ if (netif_running(dev)) {
+ netif_device_detach(dev);
+ ks8851_net_stop(dev);
+ }
+
+ return 0;
+}
+
+static int ks8851_resume(struct spi_device *spi)
+{
+ struct ks8851_net *ks = dev_get_drvdata(&spi->dev);
+ struct net_device *dev = ks->netdev;
+
+ if (netif_running(dev)) {
+ ks8851_net_open(dev);
+ netif_device_attach(dev);
+ }
+
+ return 0;
+}
+#else
+#define ks8851_suspend NULL
+#define ks8851_resume NULL
+#endif
+
+static int __devinit ks8851_probe(struct spi_device *spi)
+{
+ struct net_device *ndev;
+ struct ks8851_net *ks;
+ int ret;
+
+ ndev = alloc_etherdev(sizeof(struct ks8851_net));
+ if (!ndev) {
+ dev_err(&spi->dev, "failed to alloc ethernet device\n");
+ return -ENOMEM;
+ }
+
+ spi->bits_per_word = 8;
+
+ ks = netdev_priv(ndev);
+
+ ks->netdev = ndev;
+ ks->spidev = spi;
+ ks->tx_space = 6144;
+
+ mutex_init(&ks->lock);
+ spin_lock_init(&ks->statelock);
+
+ INIT_WORK(&ks->tx_work, ks8851_tx_work);
+ INIT_WORK(&ks->irq_work, ks8851_irq_work);
+ INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work);
+
+ /* initialise pre-made spi transfer messages */
+
+ spi_message_init(&ks->spi_msg1);
+ spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1);
+
+ spi_message_init(&ks->spi_msg2);
+ spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2);
+ spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2);
+
+ /* setup mii state */
+ ks->mii.dev = ndev;
+ ks->mii.phy_id = 1,
+ ks->mii.phy_id_mask = 1;
+ ks->mii.reg_num_mask = 0xf;
+ ks->mii.mdio_read = ks8851_phy_read;
+ ks->mii.mdio_write = ks8851_phy_write;
+
+ dev_info(&spi->dev, "message enable is %d\n", msg_enable);
+
+ /* set the default message enable */
+ ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
+ NETIF_MSG_PROBE |
+ NETIF_MSG_LINK));
+
+ skb_queue_head_init(&ks->txq);
+
+ SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops);
+ SET_NETDEV_DEV(ndev, &spi->dev);
+
+ dev_set_drvdata(&spi->dev, ks);
+
+ ndev->if_port = IF_PORT_100BASET;
+ ndev->netdev_ops = &ks8851_netdev_ops;
+ ndev->irq = spi->irq;
+
+ /* issue a global soft reset to reset the device. */
+ ks8851_soft_reset(ks, GRR_GSR);
+
+ /* simple check for a valid chip being connected to the bus */
+
+ if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
+ dev_err(&spi->dev, "failed to read device ID\n");
+ ret = -ENODEV;
+ goto err_id;
+ }
+
+ /* cache the contents of the CCR register for EEPROM, etc. */
+ ks->rc_ccr = ks8851_rdreg16(ks, KS_CCR);
+
+ if (ks->rc_ccr & CCR_EEPROM)
+ ks->eeprom_size = 128;
+ else
+ ks->eeprom_size = 0;
+
+ ks8851_read_selftest(ks);
+ ks8851_init_mac(ks);
+
+ ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW,
+ ndev->name, ks);
+ if (ret < 0) {
+ dev_err(&spi->dev, "failed to get irq\n");
+ goto err_irq;
+ }
+
+ ret = register_netdev(ndev);
+ if (ret) {
+ dev_err(&spi->dev, "failed to register network device\n");
+ goto err_netdev;
+ }
+
+ netdev_info(ndev, "revision %d, MAC %pM, IRQ %d\n",
+ CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)),
+ ndev->dev_addr, ndev->irq);
+
+ return 0;
+
+
+err_netdev:
+ free_irq(ndev->irq, ndev);
+
+err_id:
+err_irq:
+ free_netdev(ndev);
+ return ret;
+}
+
+static int __devexit ks8851_remove(struct spi_device *spi)
+{
+ struct ks8851_net *priv = dev_get_drvdata(&spi->dev);
+
+ if (netif_msg_drv(priv))
+ dev_info(&spi->dev, "remove\n");
+
+ unregister_netdev(priv->netdev);
+ free_irq(spi->irq, priv);
+ free_netdev(priv->netdev);
+
+ return 0;
+}
+
+static struct spi_driver ks8851_driver = {
+ .driver = {
+ .name = "ks8851",
+ .owner = THIS_MODULE,
+ },
+ .probe = ks8851_probe,
+ .remove = __devexit_p(ks8851_remove),
+ .suspend = ks8851_suspend,
+ .resume = ks8851_resume,
+};
+
+static int __init ks8851_init(void)
+{
+ return spi_register_driver(&ks8851_driver);
+}
+
+static void __exit ks8851_exit(void)
+{
+ spi_unregister_driver(&ks8851_driver);
+}
+
+module_init(ks8851_init);
+module_exit(ks8851_exit);
+
+MODULE_DESCRIPTION("KS8851 Network driver");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_LICENSE("GPL");
+
+module_param_named(message, msg_enable, int, 0);
+MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
+MODULE_ALIAS("spi:ks8851");
--- /dev/null
+/* drivers/net/ks8851.h
+ *
+ * Copyright 2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * KS8851 register definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define KS_CCR 0x08
+#define CCR_EEPROM (1 << 9)
+#define CCR_SPI (1 << 8)
+#define CCR_32PIN (1 << 0)
+
+/* MAC address registers */
+#define KS_MAR(_m) 0x15 - (_m)
+#define KS_MARL 0x10
+#define KS_MARM 0x12
+#define KS_MARH 0x14
+
+#define KS_OBCR 0x20
+#define OBCR_ODS_16mA (1 << 6)
+
+#define KS_EEPCR 0x22
+#define EEPCR_EESRWA (1 << 5)
+#define EEPCR_EESA (1 << 4)
+#define EEPCR_EESB_OFFSET 3
+#define EEPCR_EESB (1 << EEPCR_EESB_OFFSET)
+#define EEPCR_EEDO (1 << 2)
+#define EEPCR_EESCK (1 << 1)
+#define EEPCR_EECS (1 << 0)
+
+#define EEPROM_OP_LEN 3 /* bits:*/
+#define EEPROM_OP_READ 0x06
+#define EEPROM_OP_EWEN 0x04
+#define EEPROM_OP_WRITE 0x05
+#define EEPROM_OP_EWDS 0x14
+
+#define EEPROM_DATA_LEN 16 /* 16 bits EEPROM */
+#define EEPROM_WRITE_TIME 4 /* wrt ack time in ms */
+#define EEPROM_SK_PERIOD 400 /* in us */
+
+#define KS_MBIR 0x24
+#define MBIR_TXMBF (1 << 12)
+#define MBIR_TXMBFA (1 << 11)
+#define MBIR_RXMBF (1 << 4)
+#define MBIR_RXMBFA (1 << 3)
+
+#define KS_GRR 0x26
+#define GRR_QMU (1 << 1)
+#define GRR_GSR (1 << 0)
+
+#define KS_WFCR 0x2A
+#define WFCR_MPRXE (1 << 7)
+#define WFCR_WF3E (1 << 3)
+#define WFCR_WF2E (1 << 2)
+#define WFCR_WF1E (1 << 1)
+#define WFCR_WF0E (1 << 0)
+
+#define KS_WF0CRC0 0x30
+#define KS_WF0CRC1 0x32
+#define KS_WF0BM0 0x34
+#define KS_WF0BM1 0x36
+#define KS_WF0BM2 0x38
+#define KS_WF0BM3 0x3A
+
+#define KS_WF1CRC0 0x40
+#define KS_WF1CRC1 0x42
+#define KS_WF1BM0 0x44
+#define KS_WF1BM1 0x46
+#define KS_WF1BM2 0x48
+#define KS_WF1BM3 0x4A
+
+#define KS_WF2CRC0 0x50
+#define KS_WF2CRC1 0x52
+#define KS_WF2BM0 0x54
+#define KS_WF2BM1 0x56
+#define KS_WF2BM2 0x58
+#define KS_WF2BM3 0x5A
+
+#define KS_WF3CRC0 0x60
+#define KS_WF3CRC1 0x62
+#define KS_WF3BM0 0x64
+#define KS_WF3BM1 0x66
+#define KS_WF3BM2 0x68
+#define KS_WF3BM3 0x6A
+
+#define KS_TXCR 0x70
+#define TXCR_TCGICMP (1 << 8)
+#define TXCR_TCGUDP (1 << 7)
+#define TXCR_TCGTCP (1 << 6)
+#define TXCR_TCGIP (1 << 5)
+#define TXCR_FTXQ (1 << 4)
+#define TXCR_TXFCE (1 << 3)
+#define TXCR_TXPE (1 << 2)
+#define TXCR_TXCRC (1 << 1)
+#define TXCR_TXE (1 << 0)
+
+#define KS_TXSR 0x72
+#define TXSR_TXLC (1 << 13)
+#define TXSR_TXMC (1 << 12)
+#define TXSR_TXFID_MASK (0x3f << 0)
+#define TXSR_TXFID_SHIFT (0)
+#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f)
+
+#define KS_RXCR1 0x74
+#define RXCR1_FRXQ (1 << 15)
+#define RXCR1_RXUDPFCC (1 << 14)
+#define RXCR1_RXTCPFCC (1 << 13)
+#define RXCR1_RXIPFCC (1 << 12)
+#define RXCR1_RXPAFMA (1 << 11)
+#define RXCR1_RXFCE (1 << 10)
+#define RXCR1_RXEFE (1 << 9)
+#define RXCR1_RXMAFMA (1 << 8)
+#define RXCR1_RXBE (1 << 7)
+#define RXCR1_RXME (1 << 6)
+#define RXCR1_RXUE (1 << 5)
+#define RXCR1_RXAE (1 << 4)
+#define RXCR1_RXINVF (1 << 1)
+#define RXCR1_RXE (1 << 0)
+
+#define KS_RXCR2 0x76
+#define RXCR2_SRDBL_MASK (0x7 << 5)
+#define RXCR2_SRDBL_SHIFT (5)
+#define RXCR2_SRDBL_4B (0x0 << 5)
+#define RXCR2_SRDBL_8B (0x1 << 5)
+#define RXCR2_SRDBL_16B (0x2 << 5)
+#define RXCR2_SRDBL_32B (0x3 << 5)
+#define RXCR2_SRDBL_FRAME (0x4 << 5)
+#define RXCR2_IUFFP (1 << 4)
+#define RXCR2_RXIUFCEZ (1 << 3)
+#define RXCR2_UDPLFE (1 << 2)
+#define RXCR2_RXICMPFCC (1 << 1)
+#define RXCR2_RXSAF (1 << 0)
+
+#define KS_TXMIR 0x78
+
+#define KS_RXFHSR 0x7C
+#define RXFSHR_RXFV (1 << 15)
+#define RXFSHR_RXICMPFCS (1 << 13)
+#define RXFSHR_RXIPFCS (1 << 12)
+#define RXFSHR_RXTCPFCS (1 << 11)
+#define RXFSHR_RXUDPFCS (1 << 10)
+#define RXFSHR_RXBF (1 << 7)
+#define RXFSHR_RXMF (1 << 6)
+#define RXFSHR_RXUF (1 << 5)
+#define RXFSHR_RXMR (1 << 4)
+#define RXFSHR_RXFT (1 << 3)
+#define RXFSHR_RXFTL (1 << 2)
+#define RXFSHR_RXRF (1 << 1)
+#define RXFSHR_RXCE (1 << 0)
+
+#define KS_RXFHBCR 0x7E
+#define KS_TXQCR 0x80
+#define TXQCR_AETFE (1 << 2)
+#define TXQCR_TXQMAM (1 << 1)
+#define TXQCR_METFE (1 << 0)
+
+#define KS_RXQCR 0x82
+#define RXQCR_RXDTTS (1 << 12)
+#define RXQCR_RXDBCTS (1 << 11)
+#define RXQCR_RXFCTS (1 << 10)
+#define RXQCR_RXIPHTOE (1 << 9)
+#define RXQCR_RXDTTE (1 << 7)
+#define RXQCR_RXDBCTE (1 << 6)
+#define RXQCR_RXFCTE (1 << 5)
+#define RXQCR_ADRFE (1 << 4)
+#define RXQCR_SDA (1 << 3)
+#define RXQCR_RRXEF (1 << 0)
+
+#define KS_TXFDPR 0x84
+#define TXFDPR_TXFPAI (1 << 14)
+#define TXFDPR_TXFP_MASK (0x7ff << 0)
+#define TXFDPR_TXFP_SHIFT (0)
+
+#define KS_RXFDPR 0x86
+#define RXFDPR_RXFPAI (1 << 14)
+
+#define KS_RXDTTR 0x8C
+#define KS_RXDBCTR 0x8E
+
+#define KS_IER 0x90
+#define KS_ISR 0x92
+#define IRQ_LCI (1 << 15)
+#define IRQ_TXI (1 << 14)
+#define IRQ_RXI (1 << 13)
+#define IRQ_RXOI (1 << 11)
+#define IRQ_TXPSI (1 << 9)
+#define IRQ_RXPSI (1 << 8)
+#define IRQ_TXSAI (1 << 6)
+#define IRQ_RXWFDI (1 << 5)
+#define IRQ_RXMPDI (1 << 4)
+#define IRQ_LDI (1 << 3)
+#define IRQ_EDI (1 << 2)
+#define IRQ_SPIBEI (1 << 1)
+#define IRQ_DEDI (1 << 0)
+
+#define KS_RXFCTR 0x9C
+#define KS_RXFC 0x9D
+#define RXFCTR_RXFC_MASK (0xff << 8)
+#define RXFCTR_RXFC_SHIFT (8)
+#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff)
+#define RXFCTR_RXFCT_MASK (0xff << 0)
+#define RXFCTR_RXFCT_SHIFT (0)
+
+#define KS_TXNTFSR 0x9E
+
+#define KS_MAHTR0 0xA0
+#define KS_MAHTR1 0xA2
+#define KS_MAHTR2 0xA4
+#define KS_MAHTR3 0xA6
+
+#define KS_FCLWR 0xB0
+#define KS_FCHWR 0xB2
+#define KS_FCOWR 0xB4
+
+#define KS_CIDER 0xC0
+#define CIDER_ID 0x8870
+#define CIDER_REV_MASK (0x7 << 1)
+#define CIDER_REV_SHIFT (1)
+#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7)
+
+#define KS_CGCR 0xC6
+
+#define KS_IACR 0xC8
+#define IACR_RDEN (1 << 12)
+#define IACR_TSEL_MASK (0x3 << 10)
+#define IACR_TSEL_SHIFT (10)
+#define IACR_TSEL_MIB (0x3 << 10)
+#define IACR_ADDR_MASK (0x1f << 0)
+#define IACR_ADDR_SHIFT (0)
+
+#define KS_IADLR 0xD0
+#define KS_IAHDR 0xD2
+
+#define KS_PMECR 0xD4
+#define PMECR_PME_DELAY (1 << 14)
+#define PMECR_PME_POL (1 << 12)
+#define PMECR_WOL_WAKEUP (1 << 11)
+#define PMECR_WOL_MAGICPKT (1 << 10)
+#define PMECR_WOL_LINKUP (1 << 9)
+#define PMECR_WOL_ENERGY (1 << 8)
+#define PMECR_AUTO_WAKE_EN (1 << 7)
+#define PMECR_WAKEUP_NORMAL (1 << 6)
+#define PMECR_WKEVT_MASK (0xf << 2)
+#define PMECR_WKEVT_SHIFT (2)
+#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf)
+#define PMECR_WKEVT_ENERGY (0x1 << 2)
+#define PMECR_WKEVT_LINK (0x2 << 2)
+#define PMECR_WKEVT_MAGICPKT (0x4 << 2)
+#define PMECR_WKEVT_FRAME (0x8 << 2)
+#define PMECR_PM_MASK (0x3 << 0)
+#define PMECR_PM_SHIFT (0)
+#define PMECR_PM_NORMAL (0x0 << 0)
+#define PMECR_PM_ENERGY (0x1 << 0)
+#define PMECR_PM_SOFTDOWN (0x2 << 0)
+#define PMECR_PM_POWERSAVE (0x3 << 0)
+
+/* Standard MII PHY data */
+#define KS_P1MBCR 0xE4
+#define KS_P1MBSR 0xE6
+#define KS_PHY1ILR 0xE8
+#define KS_PHY1IHR 0xEA
+#define KS_P1ANAR 0xEC
+#define KS_P1ANLPR 0xEE
+
+#define KS_P1SCLMD 0xF4
+#define P1SCLMD_LEDOFF (1 << 15)
+#define P1SCLMD_TXIDS (1 << 14)
+#define P1SCLMD_RESTARTAN (1 << 13)
+#define P1SCLMD_DISAUTOMDIX (1 << 10)
+#define P1SCLMD_FORCEMDIX (1 << 9)
+#define P1SCLMD_AUTONEGEN (1 << 7)
+#define P1SCLMD_FORCE100 (1 << 6)
+#define P1SCLMD_FORCEFDX (1 << 5)
+#define P1SCLMD_ADV_FLOW (1 << 4)
+#define P1SCLMD_ADV_100BT_FDX (1 << 3)
+#define P1SCLMD_ADV_100BT_HDX (1 << 2)
+#define P1SCLMD_ADV_10BT_FDX (1 << 1)
+#define P1SCLMD_ADV_10BT_HDX (1 << 0)
+
+#define KS_P1CR 0xF6
+#define P1CR_HP_MDIX (1 << 15)
+#define P1CR_REV_POL (1 << 13)
+#define P1CR_OP_100M (1 << 10)
+#define P1CR_OP_FDX (1 << 9)
+#define P1CR_OP_MDI (1 << 7)
+#define P1CR_AN_DONE (1 << 6)
+#define P1CR_LINK_GOOD (1 << 5)
+#define P1CR_PNTR_FLOW (1 << 4)
+#define P1CR_PNTR_100BT_FDX (1 << 3)
+#define P1CR_PNTR_100BT_HDX (1 << 2)
+#define P1CR_PNTR_10BT_FDX (1 << 1)
+#define P1CR_PNTR_10BT_HDX (1 << 0)
+
+/* TX Frame control */
+
+#define TXFR_TXIC (1 << 15)
+#define TXFR_TXFID_MASK (0x3f << 0)
+#define TXFR_TXFID_SHIFT (0)
+
+/* SPI frame opcodes */
+#define KS_SPIOP_RD (0x00)
+#define KS_SPIOP_WR (0x40)
+#define KS_SPIOP_RXFIFO (0x80)
+#define KS_SPIOP_TXFIFO (0xC0)
--- /dev/null
+/**
+ * drivers/net/ks8851_mll.c
+ * Copyright (c) 2009 Micrel Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/**
+ * Supports:
+ * KS8851 16bit MLL chip from Micrel Inc.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/cache.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <asm/io.h>
+
+#define DRV_NAME "ks8851_mll"
+
+static u8 KS_DEFAULT_MAC_ADDRESS[] = { 0x00, 0x10, 0xA1, 0x86, 0x95, 0x11 };
+#define MAX_RECV_FRAMES 32
+#define MAX_BUF_SIZE 2048
+#define TX_BUF_SIZE 2000
+#define RX_BUF_SIZE 2000
+
+#define KS_CCR 0x08
+#define CCR_EEPROM (1 << 9)
+#define CCR_SPI (1 << 8)
+#define CCR_8BIT (1 << 7)
+#define CCR_16BIT (1 << 6)
+#define CCR_32BIT (1 << 5)
+#define CCR_SHARED (1 << 4)
+#define CCR_32PIN (1 << 0)
+
+/* MAC address registers */
+#define KS_MARL 0x10
+#define KS_MARM 0x12
+#define KS_MARH 0x14
+
+#define KS_OBCR 0x20
+#define OBCR_ODS_16MA (1 << 6)
+
+#define KS_EEPCR 0x22
+#define EEPCR_EESA (1 << 4)
+#define EEPCR_EESB (1 << 3)
+#define EEPCR_EEDO (1 << 2)
+#define EEPCR_EESCK (1 << 1)
+#define EEPCR_EECS (1 << 0)
+
+#define KS_MBIR 0x24
+#define MBIR_TXMBF (1 << 12)
+#define MBIR_TXMBFA (1 << 11)
+#define MBIR_RXMBF (1 << 4)
+#define MBIR_RXMBFA (1 << 3)
+
+#define KS_GRR 0x26
+#define GRR_QMU (1 << 1)
+#define GRR_GSR (1 << 0)
+
+#define KS_WFCR 0x2A
+#define WFCR_MPRXE (1 << 7)
+#define WFCR_WF3E (1 << 3)
+#define WFCR_WF2E (1 << 2)
+#define WFCR_WF1E (1 << 1)
+#define WFCR_WF0E (1 << 0)
+
+#define KS_WF0CRC0 0x30
+#define KS_WF0CRC1 0x32
+#define KS_WF0BM0 0x34
+#define KS_WF0BM1 0x36
+#define KS_WF0BM2 0x38
+#define KS_WF0BM3 0x3A
+
+#define KS_WF1CRC0 0x40
+#define KS_WF1CRC1 0x42
+#define KS_WF1BM0 0x44
+#define KS_WF1BM1 0x46
+#define KS_WF1BM2 0x48
+#define KS_WF1BM3 0x4A
+
+#define KS_WF2CRC0 0x50
+#define KS_WF2CRC1 0x52
+#define KS_WF2BM0 0x54
+#define KS_WF2BM1 0x56
+#define KS_WF2BM2 0x58
+#define KS_WF2BM3 0x5A
+
+#define KS_WF3CRC0 0x60
+#define KS_WF3CRC1 0x62
+#define KS_WF3BM0 0x64
+#define KS_WF3BM1 0x66
+#define KS_WF3BM2 0x68
+#define KS_WF3BM3 0x6A
+
+#define KS_TXCR 0x70
+#define TXCR_TCGICMP (1 << 8)
+#define TXCR_TCGUDP (1 << 7)
+#define TXCR_TCGTCP (1 << 6)
+#define TXCR_TCGIP (1 << 5)
+#define TXCR_FTXQ (1 << 4)
+#define TXCR_TXFCE (1 << 3)
+#define TXCR_TXPE (1 << 2)
+#define TXCR_TXCRC (1 << 1)
+#define TXCR_TXE (1 << 0)
+
+#define KS_TXSR 0x72
+#define TXSR_TXLC (1 << 13)
+#define TXSR_TXMC (1 << 12)
+#define TXSR_TXFID_MASK (0x3f << 0)
+#define TXSR_TXFID_SHIFT (0)
+#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f)
+
+
+#define KS_RXCR1 0x74
+#define RXCR1_FRXQ (1 << 15)
+#define RXCR1_RXUDPFCC (1 << 14)
+#define RXCR1_RXTCPFCC (1 << 13)
+#define RXCR1_RXIPFCC (1 << 12)
+#define RXCR1_RXPAFMA (1 << 11)
+#define RXCR1_RXFCE (1 << 10)
+#define RXCR1_RXEFE (1 << 9)
+#define RXCR1_RXMAFMA (1 << 8)
+#define RXCR1_RXBE (1 << 7)
+#define RXCR1_RXME (1 << 6)
+#define RXCR1_RXUE (1 << 5)
+#define RXCR1_RXAE (1 << 4)
+#define RXCR1_RXINVF (1 << 1)
+#define RXCR1_RXE (1 << 0)
+#define RXCR1_FILTER_MASK (RXCR1_RXINVF | RXCR1_RXAE | \
+ RXCR1_RXMAFMA | RXCR1_RXPAFMA)
+
+#define KS_RXCR2 0x76
+#define RXCR2_SRDBL_MASK (0x7 << 5)
+#define RXCR2_SRDBL_SHIFT (5)
+#define RXCR2_SRDBL_4B (0x0 << 5)
+#define RXCR2_SRDBL_8B (0x1 << 5)
+#define RXCR2_SRDBL_16B (0x2 << 5)
+#define RXCR2_SRDBL_32B (0x3 << 5)
+/* #define RXCR2_SRDBL_FRAME (0x4 << 5) */
+#define RXCR2_IUFFP (1 << 4)
+#define RXCR2_RXIUFCEZ (1 << 3)
+#define RXCR2_UDPLFE (1 << 2)
+#define RXCR2_RXICMPFCC (1 << 1)
+#define RXCR2_RXSAF (1 << 0)
+
+#define KS_TXMIR 0x78
+
+#define KS_RXFHSR 0x7C
+#define RXFSHR_RXFV (1 << 15)
+#define RXFSHR_RXICMPFCS (1 << 13)
+#define RXFSHR_RXIPFCS (1 << 12)
+#define RXFSHR_RXTCPFCS (1 << 11)
+#define RXFSHR_RXUDPFCS (1 << 10)
+#define RXFSHR_RXBF (1 << 7)
+#define RXFSHR_RXMF (1 << 6)
+#define RXFSHR_RXUF (1 << 5)
+#define RXFSHR_RXMR (1 << 4)
+#define RXFSHR_RXFT (1 << 3)
+#define RXFSHR_RXFTL (1 << 2)
+#define RXFSHR_RXRF (1 << 1)
+#define RXFSHR_RXCE (1 << 0)
+#define RXFSHR_ERR (RXFSHR_RXCE | RXFSHR_RXRF |\
+ RXFSHR_RXFTL | RXFSHR_RXMR |\
+ RXFSHR_RXICMPFCS | RXFSHR_RXIPFCS |\
+ RXFSHR_RXTCPFCS)
+#define KS_RXFHBCR 0x7E
+#define RXFHBCR_CNT_MASK 0x0FFF
+
+#define KS_TXQCR 0x80
+#define TXQCR_AETFE (1 << 2)
+#define TXQCR_TXQMAM (1 << 1)
+#define TXQCR_METFE (1 << 0)
+
+#define KS_RXQCR 0x82
+#define RXQCR_RXDTTS (1 << 12)
+#define RXQCR_RXDBCTS (1 << 11)
+#define RXQCR_RXFCTS (1 << 10)
+#define RXQCR_RXIPHTOE (1 << 9)
+#define RXQCR_RXDTTE (1 << 7)
+#define RXQCR_RXDBCTE (1 << 6)
+#define RXQCR_RXFCTE (1 << 5)
+#define RXQCR_ADRFE (1 << 4)
+#define RXQCR_SDA (1 << 3)
+#define RXQCR_RRXEF (1 << 0)
+#define RXQCR_CMD_CNTL (RXQCR_RXFCTE|RXQCR_ADRFE)
+
+#define KS_TXFDPR 0x84
+#define TXFDPR_TXFPAI (1 << 14)
+#define TXFDPR_TXFP_MASK (0x7ff << 0)
+#define TXFDPR_TXFP_SHIFT (0)
+
+#define KS_RXFDPR 0x86
+#define RXFDPR_RXFPAI (1 << 14)
+
+#define KS_RXDTTR 0x8C
+#define KS_RXDBCTR 0x8E
+
+#define KS_IER 0x90
+#define KS_ISR 0x92
+#define IRQ_LCI (1 << 15)
+#define IRQ_TXI (1 << 14)
+#define IRQ_RXI (1 << 13)
+#define IRQ_RXOI (1 << 11)
+#define IRQ_TXPSI (1 << 9)
+#define IRQ_RXPSI (1 << 8)
+#define IRQ_TXSAI (1 << 6)
+#define IRQ_RXWFDI (1 << 5)
+#define IRQ_RXMPDI (1 << 4)
+#define IRQ_LDI (1 << 3)
+#define IRQ_EDI (1 << 2)
+#define IRQ_SPIBEI (1 << 1)
+#define IRQ_DEDI (1 << 0)
+
+#define KS_RXFCTR 0x9C
+#define RXFCTR_THRESHOLD_MASK 0x00FF
+
+#define KS_RXFC 0x9D
+#define RXFCTR_RXFC_MASK (0xff << 8)
+#define RXFCTR_RXFC_SHIFT (8)
+#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff)
+#define RXFCTR_RXFCT_MASK (0xff << 0)
+#define RXFCTR_RXFCT_SHIFT (0)
+
+#define KS_TXNTFSR 0x9E
+
+#define KS_MAHTR0 0xA0
+#define KS_MAHTR1 0xA2
+#define KS_MAHTR2 0xA4
+#define KS_MAHTR3 0xA6
+
+#define KS_FCLWR 0xB0
+#define KS_FCHWR 0xB2
+#define KS_FCOWR 0xB4
+
+#define KS_CIDER 0xC0
+#define CIDER_ID 0x8870
+#define CIDER_REV_MASK (0x7 << 1)
+#define CIDER_REV_SHIFT (1)
+#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7)
+
+#define KS_CGCR 0xC6
+#define KS_IACR 0xC8
+#define IACR_RDEN (1 << 12)
+#define IACR_TSEL_MASK (0x3 << 10)
+#define IACR_TSEL_SHIFT (10)
+#define IACR_TSEL_MIB (0x3 << 10)
+#define IACR_ADDR_MASK (0x1f << 0)
+#define IACR_ADDR_SHIFT (0)
+
+#define KS_IADLR 0xD0
+#define KS_IAHDR 0xD2
+
+#define KS_PMECR 0xD4
+#define PMECR_PME_DELAY (1 << 14)
+#define PMECR_PME_POL (1 << 12)
+#define PMECR_WOL_WAKEUP (1 << 11)
+#define PMECR_WOL_MAGICPKT (1 << 10)
+#define PMECR_WOL_LINKUP (1 << 9)
+#define PMECR_WOL_ENERGY (1 << 8)
+#define PMECR_AUTO_WAKE_EN (1 << 7)
+#define PMECR_WAKEUP_NORMAL (1 << 6)
+#define PMECR_WKEVT_MASK (0xf << 2)
+#define PMECR_WKEVT_SHIFT (2)
+#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf)
+#define PMECR_WKEVT_ENERGY (0x1 << 2)
+#define PMECR_WKEVT_LINK (0x2 << 2)
+#define PMECR_WKEVT_MAGICPKT (0x4 << 2)
+#define PMECR_WKEVT_FRAME (0x8 << 2)
+#define PMECR_PM_MASK (0x3 << 0)
+#define PMECR_PM_SHIFT (0)
+#define PMECR_PM_NORMAL (0x0 << 0)
+#define PMECR_PM_ENERGY (0x1 << 0)
+#define PMECR_PM_SOFTDOWN (0x2 << 0)
+#define PMECR_PM_POWERSAVE (0x3 << 0)
+
+/* Standard MII PHY data */
+#define KS_P1MBCR 0xE4
+#define P1MBCR_FORCE_FDX (1 << 8)
+
+#define KS_P1MBSR 0xE6
+#define P1MBSR_AN_COMPLETE (1 << 5)
+#define P1MBSR_AN_CAPABLE (1 << 3)
+#define P1MBSR_LINK_UP (1 << 2)
+
+#define KS_PHY1ILR 0xE8
+#define KS_PHY1IHR 0xEA
+#define KS_P1ANAR 0xEC
+#define KS_P1ANLPR 0xEE
+
+#define KS_P1SCLMD 0xF4
+#define P1SCLMD_LEDOFF (1 << 15)
+#define P1SCLMD_TXIDS (1 << 14)
+#define P1SCLMD_RESTARTAN (1 << 13)
+#define P1SCLMD_DISAUTOMDIX (1 << 10)
+#define P1SCLMD_FORCEMDIX (1 << 9)
+#define P1SCLMD_AUTONEGEN (1 << 7)
+#define P1SCLMD_FORCE100 (1 << 6)
+#define P1SCLMD_FORCEFDX (1 << 5)
+#define P1SCLMD_ADV_FLOW (1 << 4)
+#define P1SCLMD_ADV_100BT_FDX (1 << 3)
+#define P1SCLMD_ADV_100BT_HDX (1 << 2)
+#define P1SCLMD_ADV_10BT_FDX (1 << 1)
+#define P1SCLMD_ADV_10BT_HDX (1 << 0)
+
+#define KS_P1CR 0xF6
+#define P1CR_HP_MDIX (1 << 15)
+#define P1CR_REV_POL (1 << 13)
+#define P1CR_OP_100M (1 << 10)
+#define P1CR_OP_FDX (1 << 9)
+#define P1CR_OP_MDI (1 << 7)
+#define P1CR_AN_DONE (1 << 6)
+#define P1CR_LINK_GOOD (1 << 5)
+#define P1CR_PNTR_FLOW (1 << 4)
+#define P1CR_PNTR_100BT_FDX (1 << 3)
+#define P1CR_PNTR_100BT_HDX (1 << 2)
+#define P1CR_PNTR_10BT_FDX (1 << 1)
+#define P1CR_PNTR_10BT_HDX (1 << 0)
+
+/* TX Frame control */
+
+#define TXFR_TXIC (1 << 15)
+#define TXFR_TXFID_MASK (0x3f << 0)
+#define TXFR_TXFID_SHIFT (0)
+
+#define KS_P1SR 0xF8
+#define P1SR_HP_MDIX (1 << 15)
+#define P1SR_REV_POL (1 << 13)
+#define P1SR_OP_100M (1 << 10)
+#define P1SR_OP_FDX (1 << 9)
+#define P1SR_OP_MDI (1 << 7)
+#define P1SR_AN_DONE (1 << 6)
+#define P1SR_LINK_GOOD (1 << 5)
+#define P1SR_PNTR_FLOW (1 << 4)
+#define P1SR_PNTR_100BT_FDX (1 << 3)
+#define P1SR_PNTR_100BT_HDX (1 << 2)
+#define P1SR_PNTR_10BT_FDX (1 << 1)
+#define P1SR_PNTR_10BT_HDX (1 << 0)
+
+#define ENUM_BUS_NONE 0
+#define ENUM_BUS_8BIT 1
+#define ENUM_BUS_16BIT 2
+#define ENUM_BUS_32BIT 3
+
+#define MAX_MCAST_LST 32
+#define HW_MCAST_SIZE 8
+
+/**
+ * union ks_tx_hdr - tx header data
+ * @txb: The header as bytes
+ * @txw: The header as 16bit, little-endian words
+ *
+ * A dual representation of the tx header data to allow
+ * access to individual bytes, and to allow 16bit accesses
+ * with 16bit alignment.
+ */
+union ks_tx_hdr {
+ u8 txb[4];
+ __le16 txw[2];
+};
+
+/**
+ * struct ks_net - KS8851 driver private data
+ * @net_device : The network device we're bound to
+ * @hw_addr : start address of data register.
+ * @hw_addr_cmd : start address of command register.
+ * @txh : temporaly buffer to save status/length.
+ * @lock : Lock to ensure that the device is not accessed when busy.
+ * @pdev : Pointer to platform device.
+ * @mii : The MII state information for the mii calls.
+ * @frame_head_info : frame header information for multi-pkt rx.
+ * @statelock : Lock on this structure for tx list.
+ * @msg_enable : The message flags controlling driver output (see ethtool).
+ * @frame_cnt : number of frames received.
+ * @bus_width : i/o bus width.
+ * @irq : irq number assigned to this device.
+ * @rc_rxqcr : Cached copy of KS_RXQCR.
+ * @rc_txcr : Cached copy of KS_TXCR.
+ * @rc_ier : Cached copy of KS_IER.
+ * @sharedbus : Multipex(addr and data bus) mode indicator.
+ * @cmd_reg_cache : command register cached.
+ * @cmd_reg_cache_int : command register cached. Used in the irq handler.
+ * @promiscuous : promiscuous mode indicator.
+ * @all_mcast : mutlicast indicator.
+ * @mcast_lst_size : size of multicast list.
+ * @mcast_lst : multicast list.
+ * @mcast_bits : multicast enabed.
+ * @mac_addr : MAC address assigned to this device.
+ * @fid : frame id.
+ * @extra_byte : number of extra byte prepended rx pkt.
+ * @enabled : indicator this device works.
+ *
+ * The @lock ensures that the chip is protected when certain operations are
+ * in progress. When the read or write packet transfer is in progress, most
+ * of the chip registers are not accessible until the transfer is finished and
+ * the DMA has been de-asserted.
+ *
+ * The @statelock is used to protect information in the structure which may
+ * need to be accessed via several sources, such as the network driver layer
+ * or one of the work queues.
+ *
+ */
+
+/* Receive multiplex framer header info */
+struct type_frame_head {
+ u16 sts; /* Frame status */
+ u16 len; /* Byte count */
+};
+
+struct ks_net {
+ struct net_device *netdev;
+ void __iomem *hw_addr;
+ void __iomem *hw_addr_cmd;
+ union ks_tx_hdr txh ____cacheline_aligned;
+ struct mutex lock; /* spinlock to be interrupt safe */
+ struct platform_device *pdev;
+ struct mii_if_info mii;
+ struct type_frame_head *frame_head_info;
+ spinlock_t statelock;
+ u32 msg_enable;
+ u32 frame_cnt;
+ int bus_width;
+ int irq;
+
+ u16 rc_rxqcr;
+ u16 rc_txcr;
+ u16 rc_ier;
+ u16 sharedbus;
+ u16 cmd_reg_cache;
+ u16 cmd_reg_cache_int;
+ u16 promiscuous;
+ u16 all_mcast;
+ u16 mcast_lst_size;
+ u8 mcast_lst[MAX_MCAST_LST][ETH_ALEN];
+ u8 mcast_bits[HW_MCAST_SIZE];
+ u8 mac_addr[6];
+ u8 fid;
+ u8 extra_byte;
+ u8 enabled;
+};
+
+static int msg_enable;
+
+#define BE3 0x8000 /* Byte Enable 3 */
+#define BE2 0x4000 /* Byte Enable 2 */
+#define BE1 0x2000 /* Byte Enable 1 */
+#define BE0 0x1000 /* Byte Enable 0 */
+
+/**
+ * register read/write calls.
+ *
+ * All these calls issue transactions to access the chip's registers. They
+ * all require that the necessary lock is held to prevent accesses when the
+ * chip is busy transferring packet data (RX/TX FIFO accesses).
+ */
+
+/**
+ * ks_rdreg8 - read 8 bit register from device
+ * @ks : The chip information
+ * @offset: The register address
+ *
+ * Read a 8bit register from the chip, returning the result
+ */
+static u8 ks_rdreg8(struct ks_net *ks, int offset)
+{
+ u16 data;
+ u8 shift_bit = offset & 0x03;
+ u8 shift_data = (offset & 1) << 3;
+ ks->cmd_reg_cache = (u16) offset | (u16)(BE0 << shift_bit);
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ data = ioread16(ks->hw_addr);
+ return (u8)(data >> shift_data);
+}
+
+/**
+ * ks_rdreg16 - read 16 bit register from device
+ * @ks : The chip information
+ * @offset: The register address
+ *
+ * Read a 16bit register from the chip, returning the result
+ */
+
+static u16 ks_rdreg16(struct ks_net *ks, int offset)
+{
+ ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ return ioread16(ks->hw_addr);
+}
+
+/**
+ * ks_wrreg8 - write 8bit register value to chip
+ * @ks: The chip information
+ * @offset: The register address
+ * @value: The value to write
+ *
+ */
+static void ks_wrreg8(struct ks_net *ks, int offset, u8 value)
+{
+ u8 shift_bit = (offset & 0x03);
+ u16 value_write = (u16)(value << ((offset & 1) << 3));
+ ks->cmd_reg_cache = (u16)offset | (BE0 << shift_bit);
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ iowrite16(value_write, ks->hw_addr);
+}
+
+/**
+ * ks_wrreg16 - write 16bit register value to chip
+ * @ks: The chip information
+ * @offset: The register address
+ * @value: The value to write
+ *
+ */
+
+static void ks_wrreg16(struct ks_net *ks, int offset, u16 value)
+{
+ ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ iowrite16(value, ks->hw_addr);
+}
+
+/**
+ * ks_inblk - read a block of data from QMU. This is called after sudo DMA mode enabled.
+ * @ks: The chip state
+ * @wptr: buffer address to save data
+ * @len: length in byte to read
+ *
+ */
+static inline void ks_inblk(struct ks_net *ks, u16 *wptr, u32 len)
+{
+ len >>= 1;
+ while (len--)
+ *wptr++ = (u16)ioread16(ks->hw_addr);
+}
+
+/**
+ * ks_outblk - write data to QMU. This is called after sudo DMA mode enabled.
+ * @ks: The chip information
+ * @wptr: buffer address
+ * @len: length in byte to write
+ *
+ */
+static inline void ks_outblk(struct ks_net *ks, u16 *wptr, u32 len)
+{
+ len >>= 1;
+ while (len--)
+ iowrite16(*wptr++, ks->hw_addr);
+}
+
+static void ks_disable_int(struct ks_net *ks)
+{
+ ks_wrreg16(ks, KS_IER, 0x0000);
+} /* ks_disable_int */
+
+static void ks_enable_int(struct ks_net *ks)
+{
+ ks_wrreg16(ks, KS_IER, ks->rc_ier);
+} /* ks_enable_int */
+
+/**
+ * ks_tx_fifo_space - return the available hardware buffer size.
+ * @ks: The chip information
+ *
+ */
+static inline u16 ks_tx_fifo_space(struct ks_net *ks)
+{
+ return ks_rdreg16(ks, KS_TXMIR) & 0x1fff;
+}
+
+/**
+ * ks_save_cmd_reg - save the command register from the cache.
+ * @ks: The chip information
+ *
+ */
+static inline void ks_save_cmd_reg(struct ks_net *ks)
+{
+ /*ks8851 MLL has a bug to read back the command register.
+ * So rely on software to save the content of command register.
+ */
+ ks->cmd_reg_cache_int = ks->cmd_reg_cache;
+}
+
+/**
+ * ks_restore_cmd_reg - restore the command register from the cache and
+ * write to hardware register.
+ * @ks: The chip information
+ *
+ */
+static inline void ks_restore_cmd_reg(struct ks_net *ks)
+{
+ ks->cmd_reg_cache = ks->cmd_reg_cache_int;
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+}
+
+/**
+ * ks_set_powermode - set power mode of the device
+ * @ks: The chip information
+ * @pwrmode: The power mode value to write to KS_PMECR.
+ *
+ * Change the power mode of the chip.
+ */
+static void ks_set_powermode(struct ks_net *ks, unsigned pwrmode)
+{
+ unsigned pmecr;
+
+ netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode);
+
+ ks_rdreg16(ks, KS_GRR);
+ pmecr = ks_rdreg16(ks, KS_PMECR);
+ pmecr &= ~PMECR_PM_MASK;
+ pmecr |= pwrmode;
+
+ ks_wrreg16(ks, KS_PMECR, pmecr);
+}
+
+/**
+ * ks_read_config - read chip configuration of bus width.
+ * @ks: The chip information
+ *
+ */
+static void ks_read_config(struct ks_net *ks)
+{
+ u16 reg_data = 0;
+
+ /* Regardless of bus width, 8 bit read should always work.*/
+ reg_data = ks_rdreg8(ks, KS_CCR) & 0x00FF;
+ reg_data |= ks_rdreg8(ks, KS_CCR+1) << 8;
+
+ /* addr/data bus are multiplexed */
+ ks->sharedbus = (reg_data & CCR_SHARED) == CCR_SHARED;
+
+ /* There are garbage data when reading data from QMU,
+ depending on bus-width.
+ */
+
+ if (reg_data & CCR_8BIT) {
+ ks->bus_width = ENUM_BUS_8BIT;
+ ks->extra_byte = 1;
+ } else if (reg_data & CCR_16BIT) {
+ ks->bus_width = ENUM_BUS_16BIT;
+ ks->extra_byte = 2;
+ } else {
+ ks->bus_width = ENUM_BUS_32BIT;
+ ks->extra_byte = 4;
+ }
+}
+
+/**
+ * ks_soft_reset - issue one of the soft reset to the device
+ * @ks: The device state.
+ * @op: The bit(s) to set in the GRR
+ *
+ * Issue the relevant soft-reset command to the device's GRR register
+ * specified by @op.
+ *
+ * Note, the delays are in there as a caution to ensure that the reset
+ * has time to take effect and then complete. Since the datasheet does
+ * not currently specify the exact sequence, we have chosen something
+ * that seems to work with our device.
+ */
+static void ks_soft_reset(struct ks_net *ks, unsigned op)
+{
+ /* Disable interrupt first */
+ ks_wrreg16(ks, KS_IER, 0x0000);
+ ks_wrreg16(ks, KS_GRR, op);
+ mdelay(10); /* wait a short time to effect reset */
+ ks_wrreg16(ks, KS_GRR, 0);
+ mdelay(1); /* wait for condition to clear */
+}
+
+
+void ks_enable_qmu(struct ks_net *ks)
+{
+ u16 w;
+
+ w = ks_rdreg16(ks, KS_TXCR);
+ /* Enables QMU Transmit (TXCR). */
+ ks_wrreg16(ks, KS_TXCR, w | TXCR_TXE);
+
+ /*
+ * RX Frame Count Threshold Enable and Auto-Dequeue RXQ Frame
+ * Enable
+ */
+
+ w = ks_rdreg16(ks, KS_RXQCR);
+ ks_wrreg16(ks, KS_RXQCR, w | RXQCR_RXFCTE);
+
+ /* Enables QMU Receive (RXCR1). */
+ w = ks_rdreg16(ks, KS_RXCR1);
+ ks_wrreg16(ks, KS_RXCR1, w | RXCR1_RXE);
+ ks->enabled = true;
+} /* ks_enable_qmu */
+
+static void ks_disable_qmu(struct ks_net *ks)
+{
+ u16 w;
+
+ w = ks_rdreg16(ks, KS_TXCR);
+
+ /* Disables QMU Transmit (TXCR). */
+ w &= ~TXCR_TXE;
+ ks_wrreg16(ks, KS_TXCR, w);
+
+ /* Disables QMU Receive (RXCR1). */
+ w = ks_rdreg16(ks, KS_RXCR1);
+ w &= ~RXCR1_RXE ;
+ ks_wrreg16(ks, KS_RXCR1, w);
+
+ ks->enabled = false;
+
+} /* ks_disable_qmu */
+
+/**
+ * ks_read_qmu - read 1 pkt data from the QMU.
+ * @ks: The chip information
+ * @buf: buffer address to save 1 pkt
+ * @len: Pkt length
+ * Here is the sequence to read 1 pkt:
+ * 1. set sudo DMA mode
+ * 2. read prepend data
+ * 3. read pkt data
+ * 4. reset sudo DMA Mode
+ */
+static inline void ks_read_qmu(struct ks_net *ks, u16 *buf, u32 len)
+{
+ u32 r = ks->extra_byte & 0x1 ;
+ u32 w = ks->extra_byte - r;
+
+ /* 1. set sudo DMA mode */
+ ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
+ ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+
+ /* 2. read prepend data */
+ /**
+ * read 4 + extra bytes and discard them.
+ * extra bytes for dummy, 2 for status, 2 for len
+ */
+
+ /* use likely(r) for 8 bit access for performance */
+ if (unlikely(r))
+ ioread8(ks->hw_addr);
+ ks_inblk(ks, buf, w + 2 + 2);
+
+ /* 3. read pkt data */
+ ks_inblk(ks, buf, ALIGN(len, 4));
+
+ /* 4. reset sudo DMA Mode */
+ ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
+}
+
+/**
+ * ks_rcv - read multiple pkts data from the QMU.
+ * @ks: The chip information
+ * @netdev: The network device being opened.
+ *
+ * Read all of header information before reading pkt content.
+ * It is not allowed only port of pkts in QMU after issuing
+ * interrupt ack.
+ */
+static void ks_rcv(struct ks_net *ks, struct net_device *netdev)
+{
+ u32 i;
+ struct type_frame_head *frame_hdr = ks->frame_head_info;
+ struct sk_buff *skb;
+
+ ks->frame_cnt = ks_rdreg16(ks, KS_RXFCTR) >> 8;
+
+ /* read all header information */
+ for (i = 0; i < ks->frame_cnt; i++) {
+ /* Checking Received packet status */
+ frame_hdr->sts = ks_rdreg16(ks, KS_RXFHSR);
+ /* Get packet len from hardware */
+ frame_hdr->len = ks_rdreg16(ks, KS_RXFHBCR);
+ frame_hdr++;
+ }
+
+ frame_hdr = ks->frame_head_info;
+ while (ks->frame_cnt--) {
+ skb = dev_alloc_skb(frame_hdr->len + 16);
+ if (likely(skb && (frame_hdr->sts & RXFSHR_RXFV) &&
+ (frame_hdr->len < RX_BUF_SIZE) && frame_hdr->len)) {
+ skb_reserve(skb, 2);
+ /* read data block including CRC 4 bytes */
+ ks_read_qmu(ks, (u16 *)skb->data, frame_hdr->len);
+ skb_put(skb, frame_hdr->len);
+ skb->protocol = eth_type_trans(skb, netdev);
+ netif_rx(skb);
+ } else {
+ pr_err("%s: err:skb alloc\n", __func__);
+ ks_wrreg16(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_RRXEF));
+ if (skb)
+ dev_kfree_skb_irq(skb);
+ }
+ frame_hdr++;
+ }
+}
+
+/**
+ * ks_update_link_status - link status update.
+ * @netdev: The network device being opened.
+ * @ks: The chip information
+ *
+ */
+
+static void ks_update_link_status(struct net_device *netdev, struct ks_net *ks)
+{
+ /* check the status of the link */
+ u32 link_up_status;
+ if (ks_rdreg16(ks, KS_P1SR) & P1SR_LINK_GOOD) {
+ netif_carrier_on(netdev);
+ link_up_status = true;
+ } else {
+ netif_carrier_off(netdev);
+ link_up_status = false;
+ }
+ netif_dbg(ks, link, ks->netdev,
+ "%s: %s\n", __func__, link_up_status ? "UP" : "DOWN");
+}
+
+/**
+ * ks_irq - device interrupt handler
+ * @irq: Interrupt number passed from the IRQ hnalder.
+ * @pw: The private word passed to register_irq(), our struct ks_net.
+ *
+ * This is the handler invoked to find out what happened
+ *
+ * Read the interrupt status, work out what needs to be done and then clear
+ * any of the interrupts that are not needed.
+ */
+
+static irqreturn_t ks_irq(int irq, void *pw)
+{
+ struct net_device *netdev = pw;
+ struct ks_net *ks = netdev_priv(netdev);
+ u16 status;
+
+ /*this should be the first in IRQ handler */
+ ks_save_cmd_reg(ks);
+
+ status = ks_rdreg16(ks, KS_ISR);
+ if (unlikely(!status)) {
+ ks_restore_cmd_reg(ks);
+ return IRQ_NONE;
+ }
+
+ ks_wrreg16(ks, KS_ISR, status);
+
+ if (likely(status & IRQ_RXI))
+ ks_rcv(ks, netdev);
+
+ if (unlikely(status & IRQ_LCI))
+ ks_update_link_status(netdev, ks);
+
+ if (unlikely(status & IRQ_TXI))
+ netif_wake_queue(netdev);
+
+ if (unlikely(status & IRQ_LDI)) {
+
+ u16 pmecr = ks_rdreg16(ks, KS_PMECR);
+ pmecr &= ~PMECR_WKEVT_MASK;
+ ks_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);
+ }
+
+ /* this should be the last in IRQ handler*/
+ ks_restore_cmd_reg(ks);
+ return IRQ_HANDLED;
+}
+
+
+/**
+ * ks_net_open - open network device
+ * @netdev: The network device being opened.
+ *
+ * Called when the network device is marked active, such as a user executing
+ * 'ifconfig up' on the device.
+ */
+static int ks_net_open(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ int err;
+
+#define KS_INT_FLAGS (IRQF_DISABLED|IRQF_TRIGGER_LOW)
+ /* lock the card, even if we may not actually do anything
+ * else at the moment.
+ */
+
+ netif_dbg(ks, ifup, ks->netdev, "%s - entry\n", __func__);
+
+ /* reset the HW */
+ err = request_irq(ks->irq, ks_irq, KS_INT_FLAGS, DRV_NAME, netdev);
+
+ if (err) {
+ pr_err("Failed to request IRQ: %d: %d\n", ks->irq, err);
+ return err;
+ }
+
+ /* wake up powermode to normal mode */
+ ks_set_powermode(ks, PMECR_PM_NORMAL);
+ mdelay(1); /* wait for normal mode to take effect */
+
+ ks_wrreg16(ks, KS_ISR, 0xffff);
+ ks_enable_int(ks);
+ ks_enable_qmu(ks);
+ netif_start_queue(ks->netdev);
+
+ netif_dbg(ks, ifup, ks->netdev, "network device up\n");
+
+ return 0;
+}
+
+/**
+ * ks_net_stop - close network device
+ * @netdev: The device being closed.
+ *
+ * Called to close down a network device which has been active. Cancell any
+ * work, shutdown the RX and TX process and then place the chip into a low
+ * power state whilst it is not being used.
+ */
+static int ks_net_stop(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+
+ netif_info(ks, ifdown, netdev, "shutting down\n");
+
+ netif_stop_queue(netdev);
+
+ mutex_lock(&ks->lock);
+
+ /* turn off the IRQs and ack any outstanding */
+ ks_wrreg16(ks, KS_IER, 0x0000);
+ ks_wrreg16(ks, KS_ISR, 0xffff);
+
+ /* shutdown RX/TX QMU */
+ ks_disable_qmu(ks);
+
+ /* set powermode to soft power down to save power */
+ ks_set_powermode(ks, PMECR_PM_SOFTDOWN);
+ free_irq(ks->irq, netdev);
+ mutex_unlock(&ks->lock);
+ return 0;
+}
+
+
+/**
+ * ks_write_qmu - write 1 pkt data to the QMU.
+ * @ks: The chip information
+ * @pdata: buffer address to save 1 pkt
+ * @len: Pkt length in byte
+ * Here is the sequence to write 1 pkt:
+ * 1. set sudo DMA mode
+ * 2. write status/length
+ * 3. write pkt data
+ * 4. reset sudo DMA Mode
+ * 5. reset sudo DMA mode
+ * 6. Wait until pkt is out
+ */
+static void ks_write_qmu(struct ks_net *ks, u8 *pdata, u16 len)
+{
+ /* start header at txb[0] to align txw entries */
+ ks->txh.txw[0] = 0;
+ ks->txh.txw[1] = cpu_to_le16(len);
+
+ /* 1. set sudo-DMA mode */
+ ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+ /* 2. write status/lenth info */
+ ks_outblk(ks, ks->txh.txw, 4);
+ /* 3. write pkt data */
+ ks_outblk(ks, (u16 *)pdata, ALIGN(len, 4));
+ /* 4. reset sudo-DMA mode */
+ ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
+ /* 5. Enqueue Tx(move the pkt from TX buffer into TXQ) */
+ ks_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
+ /* 6. wait until TXQCR_METFE is auto-cleared */
+ while (ks_rdreg16(ks, KS_TXQCR) & TXQCR_METFE)
+ ;
+}
+
+/**
+ * ks_start_xmit - transmit packet
+ * @skb : The buffer to transmit
+ * @netdev : The device used to transmit the packet.
+ *
+ * Called by the network layer to transmit the @skb.
+ * spin_lock_irqsave is required because tx and rx should be mutual exclusive.
+ * So while tx is in-progress, prevent IRQ interrupt from happenning.
+ */
+static int ks_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+ int retv = NETDEV_TX_OK;
+ struct ks_net *ks = netdev_priv(netdev);
+
+ disable_irq(netdev->irq);
+ ks_disable_int(ks);
+ spin_lock(&ks->statelock);
+
+ /* Extra space are required:
+ * 4 byte for alignment, 4 for status/length, 4 for CRC
+ */
+
+ if (likely(ks_tx_fifo_space(ks) >= skb->len + 12)) {
+ ks_write_qmu(ks, skb->data, skb->len);
+ dev_kfree_skb(skb);
+ } else
+ retv = NETDEV_TX_BUSY;
+ spin_unlock(&ks->statelock);
+ ks_enable_int(ks);
+ enable_irq(netdev->irq);
+ return retv;
+}
+
+/**
+ * ks_start_rx - ready to serve pkts
+ * @ks : The chip information
+ *
+ */
+static void ks_start_rx(struct ks_net *ks)
+{
+ u16 cntl;
+
+ /* Enables QMU Receive (RXCR1). */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+ cntl |= RXCR1_RXE ;
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+} /* ks_start_rx */
+
+/**
+ * ks_stop_rx - stop to serve pkts
+ * @ks : The chip information
+ *
+ */
+static void ks_stop_rx(struct ks_net *ks)
+{
+ u16 cntl;
+
+ /* Disables QMU Receive (RXCR1). */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+ cntl &= ~RXCR1_RXE ;
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+
+} /* ks_stop_rx */
+
+static unsigned long const ethernet_polynomial = 0x04c11db7U;
+
+static unsigned long ether_gen_crc(int length, u8 *data)
+{
+ long crc = -1;
+ while (--length >= 0) {
+ u8 current_octet = *data++;
+ int bit;
+
+ for (bit = 0; bit < 8; bit++, current_octet >>= 1) {
+ crc = (crc << 1) ^
+ ((crc < 0) ^ (current_octet & 1) ?
+ ethernet_polynomial : 0);
+ }
+ }
+ return (unsigned long)crc;
+} /* ether_gen_crc */
+
+/**
+* ks_set_grpaddr - set multicast information
+* @ks : The chip information
+*/
+
+static void ks_set_grpaddr(struct ks_net *ks)
+{
+ u8 i;
+ u32 index, position, value;
+
+ memset(ks->mcast_bits, 0, sizeof(u8) * HW_MCAST_SIZE);
+
+ for (i = 0; i < ks->mcast_lst_size; i++) {
+ position = (ether_gen_crc(6, ks->mcast_lst[i]) >> 26) & 0x3f;
+ index = position >> 3;
+ value = 1 << (position & 7);
+ ks->mcast_bits[index] |= (u8)value;
+ }
+
+ for (i = 0; i < HW_MCAST_SIZE; i++) {
+ if (i & 1) {
+ ks_wrreg16(ks, (u16)((KS_MAHTR0 + i) & ~1),
+ (ks->mcast_bits[i] << 8) |
+ ks->mcast_bits[i - 1]);
+ }
+ }
+} /* ks_set_grpaddr */
+
+/*
+* ks_clear_mcast - clear multicast information
+*
+* @ks : The chip information
+* This routine removes all mcast addresses set in the hardware.
+*/
+
+static void ks_clear_mcast(struct ks_net *ks)
+{
+ u16 i, mcast_size;
+ for (i = 0; i < HW_MCAST_SIZE; i++)
+ ks->mcast_bits[i] = 0;
+
+ mcast_size = HW_MCAST_SIZE >> 2;
+ for (i = 0; i < mcast_size; i++)
+ ks_wrreg16(ks, KS_MAHTR0 + (2*i), 0);
+}
+
+static void ks_set_promis(struct ks_net *ks, u16 promiscuous_mode)
+{
+ u16 cntl;
+ ks->promiscuous = promiscuous_mode;
+ ks_stop_rx(ks); /* Stop receiving for reconfiguration */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+
+ cntl &= ~RXCR1_FILTER_MASK;
+ if (promiscuous_mode)
+ /* Enable Promiscuous mode */
+ cntl |= RXCR1_RXAE | RXCR1_RXINVF;
+ else
+ /* Disable Promiscuous mode (default normal mode) */
+ cntl |= RXCR1_RXPAFMA;
+
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+
+ if (ks->enabled)
+ ks_start_rx(ks);
+
+} /* ks_set_promis */
+
+static void ks_set_mcast(struct ks_net *ks, u16 mcast)
+{
+ u16 cntl;
+
+ ks->all_mcast = mcast;
+ ks_stop_rx(ks); /* Stop receiving for reconfiguration */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+ cntl &= ~RXCR1_FILTER_MASK;
+ if (mcast)
+ /* Enable "Perfect with Multicast address passed mode" */
+ cntl |= (RXCR1_RXAE | RXCR1_RXMAFMA | RXCR1_RXPAFMA);
+ else
+ /**
+ * Disable "Perfect with Multicast address passed
+ * mode" (normal mode).
+ */
+ cntl |= RXCR1_RXPAFMA;
+
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+
+ if (ks->enabled)
+ ks_start_rx(ks);
+} /* ks_set_mcast */
+
+static void ks_set_rx_mode(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ struct netdev_hw_addr *ha;
+
+ /* Turn on/off promiscuous mode. */
+ if ((netdev->flags & IFF_PROMISC) == IFF_PROMISC)
+ ks_set_promis(ks,
+ (u16)((netdev->flags & IFF_PROMISC) == IFF_PROMISC));
+ /* Turn on/off all mcast mode. */
+ else if ((netdev->flags & IFF_ALLMULTI) == IFF_ALLMULTI)
+ ks_set_mcast(ks,
+ (u16)((netdev->flags & IFF_ALLMULTI) == IFF_ALLMULTI));
+ else
+ ks_set_promis(ks, false);
+
+ if ((netdev->flags & IFF_MULTICAST) && netdev_mc_count(netdev)) {
+ if (netdev_mc_count(netdev) <= MAX_MCAST_LST) {
+ int i = 0;
+
+ netdev_for_each_mc_addr(ha, netdev) {
+ if (i >= MAX_MCAST_LST)
+ break;
+ memcpy(ks->mcast_lst[i++], ha->addr, ETH_ALEN);
+ }
+ ks->mcast_lst_size = (u8)i;
+ ks_set_grpaddr(ks);
+ } else {
+ /**
+ * List too big to support so
+ * turn on all mcast mode.
+ */
+ ks->mcast_lst_size = MAX_MCAST_LST;
+ ks_set_mcast(ks, true);
+ }
+ } else {
+ ks->mcast_lst_size = 0;
+ ks_clear_mcast(ks);
+ }
+} /* ks_set_rx_mode */
+
+static void ks_set_mac(struct ks_net *ks, u8 *data)
+{
+ u16 *pw = (u16 *)data;
+ u16 w, u;
+
+ ks_stop_rx(ks); /* Stop receiving for reconfiguration */
+
+ u = *pw++;
+ w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
+ ks_wrreg16(ks, KS_MARH, w);
+
+ u = *pw++;
+ w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
+ ks_wrreg16(ks, KS_MARM, w);
+
+ u = *pw;
+ w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
+ ks_wrreg16(ks, KS_MARL, w);
+
+ memcpy(ks->mac_addr, data, 6);
+
+ if (ks->enabled)
+ ks_start_rx(ks);
+}
+
+static int ks_set_mac_address(struct net_device *netdev, void *paddr)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ struct sockaddr *addr = paddr;
+ u8 *da;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+
+ da = (u8 *)netdev->dev_addr;
+
+ ks_set_mac(ks, da);
+ return 0;
+}
+
+static int ks_net_ioctl(struct net_device *netdev, struct ifreq *req, int cmd)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+
+ if (!netif_running(netdev))
+ return -EINVAL;
+
+ return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
+}
+
+static const struct net_device_ops ks_netdev_ops = {
+ .ndo_open = ks_net_open,
+ .ndo_stop = ks_net_stop,
+ .ndo_do_ioctl = ks_net_ioctl,
+ .ndo_start_xmit = ks_start_xmit,
+ .ndo_set_mac_address = ks_set_mac_address,
+ .ndo_set_rx_mode = ks_set_rx_mode,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
+/* ethtool support */
+
+static void ks_get_drvinfo(struct net_device *netdev,
+ struct ethtool_drvinfo *di)
+{
+ strlcpy(di->driver, DRV_NAME, sizeof(di->driver));
+ strlcpy(di->version, "1.00", sizeof(di->version));
+ strlcpy(di->bus_info, dev_name(netdev->dev.parent),
+ sizeof(di->bus_info));
+}
+
+static u32 ks_get_msglevel(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return ks->msg_enable;
+}
+
+static void ks_set_msglevel(struct net_device *netdev, u32 to)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ ks->msg_enable = to;
+}
+
+static int ks_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_ethtool_gset(&ks->mii, cmd);
+}
+
+static int ks_set_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_ethtool_sset(&ks->mii, cmd);
+}
+
+static u32 ks_get_link(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_link_ok(&ks->mii);
+}
+
+static int ks_nway_reset(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_nway_restart(&ks->mii);
+}
+
+static const struct ethtool_ops ks_ethtool_ops = {
+ .get_drvinfo = ks_get_drvinfo,
+ .get_msglevel = ks_get_msglevel,
+ .set_msglevel = ks_set_msglevel,
+ .get_settings = ks_get_settings,
+ .set_settings = ks_set_settings,
+ .get_link = ks_get_link,
+ .nway_reset = ks_nway_reset,
+};
+
+/* MII interface controls */
+
+/**
+ * ks_phy_reg - convert MII register into a KS8851 register
+ * @reg: MII register number.
+ *
+ * Return the KS8851 register number for the corresponding MII PHY register
+ * if possible. Return zero if the MII register has no direct mapping to the
+ * KS8851 register set.
+ */
+static int ks_phy_reg(int reg)
+{
+ switch (reg) {
+ case MII_BMCR:
+ return KS_P1MBCR;
+ case MII_BMSR:
+ return KS_P1MBSR;
+ case MII_PHYSID1:
+ return KS_PHY1ILR;
+ case MII_PHYSID2:
+ return KS_PHY1IHR;
+ case MII_ADVERTISE:
+ return KS_P1ANAR;
+ case MII_LPA:
+ return KS_P1ANLPR;
+ }
+
+ return 0x0;
+}
+
+/**
+ * ks_phy_read - MII interface PHY register read.
+ * @netdev: The network device the PHY is on.
+ * @phy_addr: Address of PHY (ignored as we only have one)
+ * @reg: The register to read.
+ *
+ * This call reads data from the PHY register specified in @reg. Since the
+ * device does not support all the MII registers, the non-existent values
+ * are always returned as zero.
+ *
+ * We return zero for unsupported registers as the MII code does not check
+ * the value returned for any error status, and simply returns it to the
+ * caller. The mii-tool that the driver was tested with takes any -ve error
+ * as real PHY capabilities, thus displaying incorrect data to the user.
+ */
+static int ks_phy_read(struct net_device *netdev, int phy_addr, int reg)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ int ksreg;
+ int result;
+
+ ksreg = ks_phy_reg(reg);
+ if (!ksreg)
+ return 0x0; /* no error return allowed, so use zero */
+
+ mutex_lock(&ks->lock);
+ result = ks_rdreg16(ks, ksreg);
+ mutex_unlock(&ks->lock);
+
+ return result;
+}
+
+static void ks_phy_write(struct net_device *netdev,
+ int phy, int reg, int value)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ int ksreg;
+
+ ksreg = ks_phy_reg(reg);
+ if (ksreg) {
+ mutex_lock(&ks->lock);
+ ks_wrreg16(ks, ksreg, value);
+ mutex_unlock(&ks->lock);
+ }
+}
+
+/**
+ * ks_read_selftest - read the selftest memory info.
+ * @ks: The device state
+ *
+ * Read and check the TX/RX memory selftest information.
+ */
+static int ks_read_selftest(struct ks_net *ks)
+{
+ unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
+ int ret = 0;
+ unsigned rd;
+
+ rd = ks_rdreg16(ks, KS_MBIR);
+
+ if ((rd & both_done) != both_done) {
+ netdev_warn(ks->netdev, "Memory selftest not finished\n");
+ return 0;
+ }
+
+ if (rd & MBIR_TXMBFA) {
+ netdev_err(ks->netdev, "TX memory selftest fails\n");
+ ret |= 1;
+ }
+
+ if (rd & MBIR_RXMBFA) {
+ netdev_err(ks->netdev, "RX memory selftest fails\n");
+ ret |= 2;
+ }
+
+ netdev_info(ks->netdev, "the selftest passes\n");
+ return ret;
+}
+
+static void ks_setup(struct ks_net *ks)
+{
+ u16 w;
+
+ /**
+ * Configure QMU Transmit
+ */
+
+ /* Setup Transmit Frame Data Pointer Auto-Increment (TXFDPR) */
+ ks_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);
+
+ /* Setup Receive Frame Data Pointer Auto-Increment */
+ ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
+
+ /* Setup Receive Frame Threshold - 1 frame (RXFCTFC) */
+ ks_wrreg16(ks, KS_RXFCTR, 1 & RXFCTR_THRESHOLD_MASK);
+
+ /* Setup RxQ Command Control (RXQCR) */
+ ks->rc_rxqcr = RXQCR_CMD_CNTL;
+ ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+
+ /**
+ * set the force mode to half duplex, default is full duplex
+ * because if the auto-negotiation fails, most switch uses
+ * half-duplex.
+ */
+
+ w = ks_rdreg16(ks, KS_P1MBCR);
+ w &= ~P1MBCR_FORCE_FDX;
+ ks_wrreg16(ks, KS_P1MBCR, w);
+
+ w = TXCR_TXFCE | TXCR_TXPE | TXCR_TXCRC | TXCR_TCGIP;
+ ks_wrreg16(ks, KS_TXCR, w);
+
+ w = RXCR1_RXFCE | RXCR1_RXBE | RXCR1_RXUE | RXCR1_RXME | RXCR1_RXIPFCC;
+
+ if (ks->promiscuous) /* bPromiscuous */
+ w |= (RXCR1_RXAE | RXCR1_RXINVF);
+ else if (ks->all_mcast) /* Multicast address passed mode */
+ w |= (RXCR1_RXAE | RXCR1_RXMAFMA | RXCR1_RXPAFMA);
+ else /* Normal mode */
+ w |= RXCR1_RXPAFMA;
+
+ ks_wrreg16(ks, KS_RXCR1, w);
+} /*ks_setup */
+
+
+static void ks_setup_int(struct ks_net *ks)
+{
+ ks->rc_ier = 0x00;
+ /* Clear the interrupts status of the hardware. */
+ ks_wrreg16(ks, KS_ISR, 0xffff);
+
+ /* Enables the interrupts of the hardware. */
+ ks->rc_ier = (IRQ_LCI | IRQ_TXI | IRQ_RXI);
+} /* ks_setup_int */
+
+static int ks_hw_init(struct ks_net *ks)
+{
+#define MHEADER_SIZE (sizeof(struct type_frame_head) * MAX_RECV_FRAMES)
+ ks->promiscuous = 0;
+ ks->all_mcast = 0;
+ ks->mcast_lst_size = 0;
+
+ ks->frame_head_info = (struct type_frame_head *) \
+ kmalloc(MHEADER_SIZE, GFP_KERNEL);
+ if (!ks->frame_head_info) {
+ pr_err("Error: Fail to allocate frame memory\n");
+ return false;
+ }
+
+ ks_set_mac(ks, KS_DEFAULT_MAC_ADDRESS);
+ return true;
+}
+
+
+static int __devinit ks8851_probe(struct platform_device *pdev)
+{
+ int err = -ENOMEM;
+ struct resource *io_d, *io_c;
+ struct net_device *netdev;
+ struct ks_net *ks;
+ u16 id, data;
+
+ io_d = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ io_c = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+ if (!request_mem_region(io_d->start, resource_size(io_d), DRV_NAME))
+ goto err_mem_region;
+
+ if (!request_mem_region(io_c->start, resource_size(io_c), DRV_NAME))
+ goto err_mem_region1;
+
+ netdev = alloc_etherdev(sizeof(struct ks_net));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ ks = netdev_priv(netdev);
+ ks->netdev = netdev;
+ ks->hw_addr = ioremap(io_d->start, resource_size(io_d));
+
+ if (!ks->hw_addr)
+ goto err_ioremap;
+
+ ks->hw_addr_cmd = ioremap(io_c->start, resource_size(io_c));
+ if (!ks->hw_addr_cmd)
+ goto err_ioremap1;
+
+ ks->irq = platform_get_irq(pdev, 0);
+
+ if (ks->irq < 0) {
+ err = ks->irq;
+ goto err_get_irq;
+ }
+
+ ks->pdev = pdev;
+
+ mutex_init(&ks->lock);
+ spin_lock_init(&ks->statelock);
+
+ netdev->netdev_ops = &ks_netdev_ops;
+ netdev->ethtool_ops = &ks_ethtool_ops;
+
+ /* setup mii state */
+ ks->mii.dev = netdev;
+ ks->mii.phy_id = 1,
+ ks->mii.phy_id_mask = 1;
+ ks->mii.reg_num_mask = 0xf;
+ ks->mii.mdio_read = ks_phy_read;
+ ks->mii.mdio_write = ks_phy_write;
+
+ netdev_info(netdev, "message enable is %d\n", msg_enable);
+ /* set the default message enable */
+ ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
+ NETIF_MSG_PROBE |
+ NETIF_MSG_LINK));
+ ks_read_config(ks);
+
+ /* simple check for a valid chip being connected to the bus */
+ if ((ks_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
+ netdev_err(netdev, "failed to read device ID\n");
+ err = -ENODEV;
+ goto err_register;
+ }
+
+ if (ks_read_selftest(ks)) {
+ netdev_err(netdev, "failed to read device ID\n");
+ err = -ENODEV;
+ goto err_register;
+ }
+
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ platform_set_drvdata(pdev, netdev);
+
+ ks_soft_reset(ks, GRR_GSR);
+ ks_hw_init(ks);
+ ks_disable_qmu(ks);
+ ks_setup(ks);
+ ks_setup_int(ks);
+ memcpy(netdev->dev_addr, ks->mac_addr, 6);
+
+ data = ks_rdreg16(ks, KS_OBCR);
+ ks_wrreg16(ks, KS_OBCR, data | OBCR_ODS_16MA);
+
+ /**
+ * If you want to use the default MAC addr,
+ * comment out the 2 functions below.
+ */
+
+ random_ether_addr(netdev->dev_addr);
+ ks_set_mac(ks, netdev->dev_addr);
+
+ id = ks_rdreg16(ks, KS_CIDER);
+
+ netdev_info(netdev, "Found chip, family: 0x%x, id: 0x%x, rev: 0x%x\n",
+ (id >> 8) & 0xff, (id >> 4) & 0xf, (id >> 1) & 0x7);
+ return 0;
+
+err_register:
+err_get_irq:
+ iounmap(ks->hw_addr_cmd);
+err_ioremap1:
+ iounmap(ks->hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ release_mem_region(io_c->start, resource_size(io_c));
+err_mem_region1:
+ release_mem_region(io_d->start, resource_size(io_d));
+err_mem_region:
+ return err;
+}
+
+static int __devexit ks8851_remove(struct platform_device *pdev)
+{
+ struct net_device *netdev = platform_get_drvdata(pdev);
+ struct ks_net *ks = netdev_priv(netdev);
+ struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ kfree(ks->frame_head_info);
+ unregister_netdev(netdev);
+ iounmap(ks->hw_addr);
+ free_netdev(netdev);
+ release_mem_region(iomem->start, resource_size(iomem));
+ platform_set_drvdata(pdev, NULL);
+ return 0;
+
+}
+
+static struct platform_driver ks8851_platform_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = ks8851_probe,
+ .remove = __devexit_p(ks8851_remove),
+};
+
+static int __init ks8851_init(void)
+{
+ return platform_driver_register(&ks8851_platform_driver);
+}
+
+static void __exit ks8851_exit(void)
+{
+ platform_driver_unregister(&ks8851_platform_driver);
+}
+
+module_init(ks8851_init);
+module_exit(ks8851_exit);
+
+MODULE_DESCRIPTION("KS8851 MLL Network driver");
+MODULE_AUTHOR("David Choi <david.choi@micrel.com>");
+MODULE_LICENSE("GPL");
+module_param_named(message, msg_enable, int, 0);
+MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
+
--- /dev/null
+/**
+ * drivers/net/ksx884x.c - Micrel KSZ8841/2 PCI Ethernet driver
+ *
+ * Copyright (c) 2009-2010 Micrel, Inc.
+ * Tristram Ha <Tristram.Ha@micrel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/proc_fs.h>
+#include <linux/mii.h>
+#include <linux/platform_device.h>
+#include <linux/ethtool.h>
+#include <linux/etherdevice.h>
+#include <linux/in.h>
+#include <linux/ip.h>
+#include <linux/if_vlan.h>
+#include <linux/crc32.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+
+
+/* DMA Registers */
+
+#define KS_DMA_TX_CTRL 0x0000
+#define DMA_TX_ENABLE 0x00000001
+#define DMA_TX_CRC_ENABLE 0x00000002
+#define DMA_TX_PAD_ENABLE 0x00000004
+#define DMA_TX_LOOPBACK 0x00000100
+#define DMA_TX_FLOW_ENABLE 0x00000200
+#define DMA_TX_CSUM_IP 0x00010000
+#define DMA_TX_CSUM_TCP 0x00020000
+#define DMA_TX_CSUM_UDP 0x00040000
+#define DMA_TX_BURST_SIZE 0x3F000000
+
+#define KS_DMA_RX_CTRL 0x0004
+#define DMA_RX_ENABLE 0x00000001
+#define KS884X_DMA_RX_MULTICAST 0x00000002
+#define DMA_RX_PROMISCUOUS 0x00000004
+#define DMA_RX_ERROR 0x00000008
+#define DMA_RX_UNICAST 0x00000010
+#define DMA_RX_ALL_MULTICAST 0x00000020
+#define DMA_RX_BROADCAST 0x00000040
+#define DMA_RX_FLOW_ENABLE 0x00000200
+#define DMA_RX_CSUM_IP 0x00010000
+#define DMA_RX_CSUM_TCP 0x00020000
+#define DMA_RX_CSUM_UDP 0x00040000
+#define DMA_RX_BURST_SIZE 0x3F000000
+
+#define DMA_BURST_SHIFT 24
+#define DMA_BURST_DEFAULT 8
+
+#define KS_DMA_TX_START 0x0008
+#define KS_DMA_RX_START 0x000C
+#define DMA_START 0x00000001
+
+#define KS_DMA_TX_ADDR 0x0010
+#define KS_DMA_RX_ADDR 0x0014
+
+#define DMA_ADDR_LIST_MASK 0xFFFFFFFC
+#define DMA_ADDR_LIST_SHIFT 2
+
+/* MTR0 */
+#define KS884X_MULTICAST_0_OFFSET 0x0020
+#define KS884X_MULTICAST_1_OFFSET 0x0021
+#define KS884X_MULTICAST_2_OFFSET 0x0022
+#define KS884x_MULTICAST_3_OFFSET 0x0023
+/* MTR1 */
+#define KS884X_MULTICAST_4_OFFSET 0x0024
+#define KS884X_MULTICAST_5_OFFSET 0x0025
+#define KS884X_MULTICAST_6_OFFSET 0x0026
+#define KS884X_MULTICAST_7_OFFSET 0x0027
+
+/* Interrupt Registers */
+
+/* INTEN */
+#define KS884X_INTERRUPTS_ENABLE 0x0028
+/* INTST */
+#define KS884X_INTERRUPTS_STATUS 0x002C
+
+#define KS884X_INT_RX_STOPPED 0x02000000
+#define KS884X_INT_TX_STOPPED 0x04000000
+#define KS884X_INT_RX_OVERRUN 0x08000000
+#define KS884X_INT_TX_EMPTY 0x10000000
+#define KS884X_INT_RX 0x20000000
+#define KS884X_INT_TX 0x40000000
+#define KS884X_INT_PHY 0x80000000
+
+#define KS884X_INT_RX_MASK \
+ (KS884X_INT_RX | KS884X_INT_RX_OVERRUN)
+#define KS884X_INT_TX_MASK \
+ (KS884X_INT_TX | KS884X_INT_TX_EMPTY)
+#define KS884X_INT_MASK (KS884X_INT_RX | KS884X_INT_TX | KS884X_INT_PHY)
+
+/* MAC Additional Station Address */
+
+/* MAAL0 */
+#define KS_ADD_ADDR_0_LO 0x0080
+/* MAAH0 */
+#define KS_ADD_ADDR_0_HI 0x0084
+/* MAAL1 */
+#define KS_ADD_ADDR_1_LO 0x0088
+/* MAAH1 */
+#define KS_ADD_ADDR_1_HI 0x008C
+/* MAAL2 */
+#define KS_ADD_ADDR_2_LO 0x0090
+/* MAAH2 */
+#define KS_ADD_ADDR_2_HI 0x0094
+/* MAAL3 */
+#define KS_ADD_ADDR_3_LO 0x0098
+/* MAAH3 */
+#define KS_ADD_ADDR_3_HI 0x009C
+/* MAAL4 */
+#define KS_ADD_ADDR_4_LO 0x00A0
+/* MAAH4 */
+#define KS_ADD_ADDR_4_HI 0x00A4
+/* MAAL5 */
+#define KS_ADD_ADDR_5_LO 0x00A8
+/* MAAH5 */
+#define KS_ADD_ADDR_5_HI 0x00AC
+/* MAAL6 */
+#define KS_ADD_ADDR_6_LO 0x00B0
+/* MAAH6 */
+#define KS_ADD_ADDR_6_HI 0x00B4
+/* MAAL7 */
+#define KS_ADD_ADDR_7_LO 0x00B8
+/* MAAH7 */
+#define KS_ADD_ADDR_7_HI 0x00BC
+/* MAAL8 */
+#define KS_ADD_ADDR_8_LO 0x00C0
+/* MAAH8 */
+#define KS_ADD_ADDR_8_HI 0x00C4
+/* MAAL9 */
+#define KS_ADD_ADDR_9_LO 0x00C8
+/* MAAH9 */
+#define KS_ADD_ADDR_9_HI 0x00CC
+/* MAAL10 */
+#define KS_ADD_ADDR_A_LO 0x00D0
+/* MAAH10 */
+#define KS_ADD_ADDR_A_HI 0x00D4
+/* MAAL11 */
+#define KS_ADD_ADDR_B_LO 0x00D8
+/* MAAH11 */
+#define KS_ADD_ADDR_B_HI 0x00DC
+/* MAAL12 */
+#define KS_ADD_ADDR_C_LO 0x00E0
+/* MAAH12 */
+#define KS_ADD_ADDR_C_HI 0x00E4
+/* MAAL13 */
+#define KS_ADD_ADDR_D_LO 0x00E8
+/* MAAH13 */
+#define KS_ADD_ADDR_D_HI 0x00EC
+/* MAAL14 */
+#define KS_ADD_ADDR_E_LO 0x00F0
+/* MAAH14 */
+#define KS_ADD_ADDR_E_HI 0x00F4
+/* MAAL15 */
+#define KS_ADD_ADDR_F_LO 0x00F8
+/* MAAH15 */
+#define KS_ADD_ADDR_F_HI 0x00FC
+
+#define ADD_ADDR_HI_MASK 0x0000FFFF
+#define ADD_ADDR_ENABLE 0x80000000
+#define ADD_ADDR_INCR 8
+
+/* Miscellaneous Registers */
+
+/* MARL */
+#define KS884X_ADDR_0_OFFSET 0x0200
+#define KS884X_ADDR_1_OFFSET 0x0201
+/* MARM */
+#define KS884X_ADDR_2_OFFSET 0x0202
+#define KS884X_ADDR_3_OFFSET 0x0203
+/* MARH */
+#define KS884X_ADDR_4_OFFSET 0x0204
+#define KS884X_ADDR_5_OFFSET 0x0205
+
+/* OBCR */
+#define KS884X_BUS_CTRL_OFFSET 0x0210
+
+#define BUS_SPEED_125_MHZ 0x0000
+#define BUS_SPEED_62_5_MHZ 0x0001
+#define BUS_SPEED_41_66_MHZ 0x0002
+#define BUS_SPEED_25_MHZ 0x0003
+
+/* EEPCR */
+#define KS884X_EEPROM_CTRL_OFFSET 0x0212
+
+#define EEPROM_CHIP_SELECT 0x0001
+#define EEPROM_SERIAL_CLOCK 0x0002
+#define EEPROM_DATA_OUT 0x0004
+#define EEPROM_DATA_IN 0x0008
+#define EEPROM_ACCESS_ENABLE 0x0010
+
+/* MBIR */
+#define KS884X_MEM_INFO_OFFSET 0x0214
+
+#define RX_MEM_TEST_FAILED 0x0008
+#define RX_MEM_TEST_FINISHED 0x0010
+#define TX_MEM_TEST_FAILED 0x0800
+#define TX_MEM_TEST_FINISHED 0x1000
+
+/* GCR */
+#define KS884X_GLOBAL_CTRL_OFFSET 0x0216
+#define GLOBAL_SOFTWARE_RESET 0x0001
+
+#define KS8841_POWER_MANAGE_OFFSET 0x0218
+
+/* WFCR */
+#define KS8841_WOL_CTRL_OFFSET 0x021A
+#define KS8841_WOL_MAGIC_ENABLE 0x0080
+#define KS8841_WOL_FRAME3_ENABLE 0x0008
+#define KS8841_WOL_FRAME2_ENABLE 0x0004
+#define KS8841_WOL_FRAME1_ENABLE 0x0002
+#define KS8841_WOL_FRAME0_ENABLE 0x0001
+
+/* WF0 */
+#define KS8841_WOL_FRAME_CRC_OFFSET 0x0220
+#define KS8841_WOL_FRAME_BYTE0_OFFSET 0x0224
+#define KS8841_WOL_FRAME_BYTE2_OFFSET 0x0228
+
+/* IACR */
+#define KS884X_IACR_P 0x04A0
+#define KS884X_IACR_OFFSET KS884X_IACR_P
+
+/* IADR1 */
+#define KS884X_IADR1_P 0x04A2
+#define KS884X_IADR2_P 0x04A4
+#define KS884X_IADR3_P 0x04A6
+#define KS884X_IADR4_P 0x04A8
+#define KS884X_IADR5_P 0x04AA
+
+#define KS884X_ACC_CTRL_SEL_OFFSET KS884X_IACR_P
+#define KS884X_ACC_CTRL_INDEX_OFFSET (KS884X_ACC_CTRL_SEL_OFFSET + 1)
+
+#define KS884X_ACC_DATA_0_OFFSET KS884X_IADR4_P
+#define KS884X_ACC_DATA_1_OFFSET (KS884X_ACC_DATA_0_OFFSET + 1)
+#define KS884X_ACC_DATA_2_OFFSET KS884X_IADR5_P
+#define KS884X_ACC_DATA_3_OFFSET (KS884X_ACC_DATA_2_OFFSET + 1)
+#define KS884X_ACC_DATA_4_OFFSET KS884X_IADR2_P
+#define KS884X_ACC_DATA_5_OFFSET (KS884X_ACC_DATA_4_OFFSET + 1)
+#define KS884X_ACC_DATA_6_OFFSET KS884X_IADR3_P
+#define KS884X_ACC_DATA_7_OFFSET (KS884X_ACC_DATA_6_OFFSET + 1)
+#define KS884X_ACC_DATA_8_OFFSET KS884X_IADR1_P
+
+/* P1MBCR */
+#define KS884X_P1MBCR_P 0x04D0
+#define KS884X_P1MBSR_P 0x04D2
+#define KS884X_PHY1ILR_P 0x04D4
+#define KS884X_PHY1IHR_P 0x04D6
+#define KS884X_P1ANAR_P 0x04D8
+#define KS884X_P1ANLPR_P 0x04DA
+
+/* P2MBCR */
+#define KS884X_P2MBCR_P 0x04E0
+#define KS884X_P2MBSR_P 0x04E2
+#define KS884X_PHY2ILR_P 0x04E4
+#define KS884X_PHY2IHR_P 0x04E6
+#define KS884X_P2ANAR_P 0x04E8
+#define KS884X_P2ANLPR_P 0x04EA
+
+#define KS884X_PHY_1_CTRL_OFFSET KS884X_P1MBCR_P
+#define PHY_CTRL_INTERVAL (KS884X_P2MBCR_P - KS884X_P1MBCR_P)
+
+#define KS884X_PHY_CTRL_OFFSET 0x00
+
+/* Mode Control Register */
+#define PHY_REG_CTRL 0
+
+#define PHY_RESET 0x8000
+#define PHY_LOOPBACK 0x4000
+#define PHY_SPEED_100MBIT 0x2000
+#define PHY_AUTO_NEG_ENABLE 0x1000
+#define PHY_POWER_DOWN 0x0800
+#define PHY_MII_DISABLE 0x0400
+#define PHY_AUTO_NEG_RESTART 0x0200
+#define PHY_FULL_DUPLEX 0x0100
+#define PHY_COLLISION_TEST 0x0080
+#define PHY_HP_MDIX 0x0020
+#define PHY_FORCE_MDIX 0x0010
+#define PHY_AUTO_MDIX_DISABLE 0x0008
+#define PHY_REMOTE_FAULT_DISABLE 0x0004
+#define PHY_TRANSMIT_DISABLE 0x0002
+#define PHY_LED_DISABLE 0x0001
+
+#define KS884X_PHY_STATUS_OFFSET 0x02
+
+/* Mode Status Register */
+#define PHY_REG_STATUS 1
+
+#define PHY_100BT4_CAPABLE 0x8000
+#define PHY_100BTX_FD_CAPABLE 0x4000
+#define PHY_100BTX_CAPABLE 0x2000
+#define PHY_10BT_FD_CAPABLE 0x1000
+#define PHY_10BT_CAPABLE 0x0800
+#define PHY_MII_SUPPRESS_CAPABLE 0x0040
+#define PHY_AUTO_NEG_ACKNOWLEDGE 0x0020
+#define PHY_REMOTE_FAULT 0x0010
+#define PHY_AUTO_NEG_CAPABLE 0x0008
+#define PHY_LINK_STATUS 0x0004
+#define PHY_JABBER_DETECT 0x0002
+#define PHY_EXTENDED_CAPABILITY 0x0001
+
+#define KS884X_PHY_ID_1_OFFSET 0x04
+#define KS884X_PHY_ID_2_OFFSET 0x06
+
+/* PHY Identifier Registers */
+#define PHY_REG_ID_1 2
+#define PHY_REG_ID_2 3
+
+#define KS884X_PHY_AUTO_NEG_OFFSET 0x08
+
+/* Auto-Negotiation Advertisement Register */
+#define PHY_REG_AUTO_NEGOTIATION 4
+
+#define PHY_AUTO_NEG_NEXT_PAGE 0x8000
+#define PHY_AUTO_NEG_REMOTE_FAULT 0x2000
+/* Not supported. */
+#define PHY_AUTO_NEG_ASYM_PAUSE 0x0800
+#define PHY_AUTO_NEG_SYM_PAUSE 0x0400
+#define PHY_AUTO_NEG_100BT4 0x0200
+#define PHY_AUTO_NEG_100BTX_FD 0x0100
+#define PHY_AUTO_NEG_100BTX 0x0080
+#define PHY_AUTO_NEG_10BT_FD 0x0040
+#define PHY_AUTO_NEG_10BT 0x0020
+#define PHY_AUTO_NEG_SELECTOR 0x001F
+#define PHY_AUTO_NEG_802_3 0x0001
+
+#define PHY_AUTO_NEG_PAUSE (PHY_AUTO_NEG_SYM_PAUSE | PHY_AUTO_NEG_ASYM_PAUSE)
+
+#define KS884X_PHY_REMOTE_CAP_OFFSET 0x0A
+
+/* Auto-Negotiation Link Partner Ability Register */
+#define PHY_REG_REMOTE_CAPABILITY 5
+
+#define PHY_REMOTE_NEXT_PAGE 0x8000
+#define PHY_REMOTE_ACKNOWLEDGE 0x4000
+#define PHY_REMOTE_REMOTE_FAULT 0x2000
+#define PHY_REMOTE_SYM_PAUSE 0x0400
+#define PHY_REMOTE_100BTX_FD 0x0100
+#define PHY_REMOTE_100BTX 0x0080
+#define PHY_REMOTE_10BT_FD 0x0040
+#define PHY_REMOTE_10BT 0x0020
+
+/* P1VCT */
+#define KS884X_P1VCT_P 0x04F0
+#define KS884X_P1PHYCTRL_P 0x04F2
+
+/* P2VCT */
+#define KS884X_P2VCT_P 0x04F4
+#define KS884X_P2PHYCTRL_P 0x04F6
+
+#define KS884X_PHY_SPECIAL_OFFSET KS884X_P1VCT_P
+#define PHY_SPECIAL_INTERVAL (KS884X_P2VCT_P - KS884X_P1VCT_P)
+
+#define KS884X_PHY_LINK_MD_OFFSET 0x00
+
+#define PHY_START_CABLE_DIAG 0x8000
+#define PHY_CABLE_DIAG_RESULT 0x6000
+#define PHY_CABLE_STAT_NORMAL 0x0000
+#define PHY_CABLE_STAT_OPEN 0x2000
+#define PHY_CABLE_STAT_SHORT 0x4000
+#define PHY_CABLE_STAT_FAILED 0x6000
+#define PHY_CABLE_10M_SHORT 0x1000
+#define PHY_CABLE_FAULT_COUNTER 0x01FF
+
+#define KS884X_PHY_PHY_CTRL_OFFSET 0x02
+
+#define PHY_STAT_REVERSED_POLARITY 0x0020
+#define PHY_STAT_MDIX 0x0010
+#define PHY_FORCE_LINK 0x0008
+#define PHY_POWER_SAVING_DISABLE 0x0004
+#define PHY_REMOTE_LOOPBACK 0x0002
+
+/* SIDER */
+#define KS884X_SIDER_P 0x0400
+#define KS884X_CHIP_ID_OFFSET KS884X_SIDER_P
+#define KS884X_FAMILY_ID_OFFSET (KS884X_CHIP_ID_OFFSET + 1)
+
+#define REG_FAMILY_ID 0x88
+
+#define REG_CHIP_ID_41 0x8810
+#define REG_CHIP_ID_42 0x8800
+
+#define KS884X_CHIP_ID_MASK_41 0xFF10
+#define KS884X_CHIP_ID_MASK 0xFFF0
+#define KS884X_CHIP_ID_SHIFT 4
+#define KS884X_REVISION_MASK 0x000E
+#define KS884X_REVISION_SHIFT 1
+#define KS8842_START 0x0001
+
+#define CHIP_IP_41_M 0x8810
+#define CHIP_IP_42_M 0x8800
+#define CHIP_IP_61_M 0x8890
+#define CHIP_IP_62_M 0x8880
+
+#define CHIP_IP_41_P 0x8850
+#define CHIP_IP_42_P 0x8840
+#define CHIP_IP_61_P 0x88D0
+#define CHIP_IP_62_P 0x88C0
+
+/* SGCR1 */
+#define KS8842_SGCR1_P 0x0402
+#define KS8842_SWITCH_CTRL_1_OFFSET KS8842_SGCR1_P
+
+#define SWITCH_PASS_ALL 0x8000
+#define SWITCH_TX_FLOW_CTRL 0x2000
+#define SWITCH_RX_FLOW_CTRL 0x1000
+#define SWITCH_CHECK_LENGTH 0x0800
+#define SWITCH_AGING_ENABLE 0x0400
+#define SWITCH_FAST_AGING 0x0200
+#define SWITCH_AGGR_BACKOFF 0x0100
+#define SWITCH_PASS_PAUSE 0x0008
+#define SWITCH_LINK_AUTO_AGING 0x0001
+
+/* SGCR2 */
+#define KS8842_SGCR2_P 0x0404
+#define KS8842_SWITCH_CTRL_2_OFFSET KS8842_SGCR2_P
+
+#define SWITCH_VLAN_ENABLE 0x8000
+#define SWITCH_IGMP_SNOOP 0x4000
+#define IPV6_MLD_SNOOP_ENABLE 0x2000
+#define IPV6_MLD_SNOOP_OPTION 0x1000
+#define PRIORITY_SCHEME_SELECT 0x0800
+#define SWITCH_MIRROR_RX_TX 0x0100
+#define UNICAST_VLAN_BOUNDARY 0x0080
+#define MULTICAST_STORM_DISABLE 0x0040
+#define SWITCH_BACK_PRESSURE 0x0020
+#define FAIR_FLOW_CTRL 0x0010
+#define NO_EXC_COLLISION_DROP 0x0008
+#define SWITCH_HUGE_PACKET 0x0004
+#define SWITCH_LEGAL_PACKET 0x0002
+#define SWITCH_BUF_RESERVE 0x0001
+
+/* SGCR3 */
+#define KS8842_SGCR3_P 0x0406
+#define KS8842_SWITCH_CTRL_3_OFFSET KS8842_SGCR3_P
+
+#define BROADCAST_STORM_RATE_LO 0xFF00
+#define SWITCH_REPEATER 0x0080
+#define SWITCH_HALF_DUPLEX 0x0040
+#define SWITCH_FLOW_CTRL 0x0020
+#define SWITCH_10_MBIT 0x0010
+#define SWITCH_REPLACE_NULL_VID 0x0008
+#define BROADCAST_STORM_RATE_HI 0x0007
+
+#define BROADCAST_STORM_RATE 0x07FF
+
+/* SGCR4 */
+#define KS8842_SGCR4_P 0x0408
+
+/* SGCR5 */
+#define KS8842_SGCR5_P 0x040A
+#define KS8842_SWITCH_CTRL_5_OFFSET KS8842_SGCR5_P
+
+#define LED_MODE 0x8200
+#define LED_SPEED_DUPLEX_ACT 0x0000
+#define LED_SPEED_DUPLEX_LINK_ACT 0x8000
+#define LED_DUPLEX_10_100 0x0200
+
+/* SGCR6 */
+#define KS8842_SGCR6_P 0x0410
+#define KS8842_SWITCH_CTRL_6_OFFSET KS8842_SGCR6_P
+
+#define KS8842_PRIORITY_MASK 3
+#define KS8842_PRIORITY_SHIFT 2
+
+/* SGCR7 */
+#define KS8842_SGCR7_P 0x0412
+#define KS8842_SWITCH_CTRL_7_OFFSET KS8842_SGCR7_P
+
+#define SWITCH_UNK_DEF_PORT_ENABLE 0x0008
+#define SWITCH_UNK_DEF_PORT_3 0x0004
+#define SWITCH_UNK_DEF_PORT_2 0x0002
+#define SWITCH_UNK_DEF_PORT_1 0x0001
+
+/* MACAR1 */
+#define KS8842_MACAR1_P 0x0470
+#define KS8842_MACAR2_P 0x0472
+#define KS8842_MACAR3_P 0x0474
+#define KS8842_MAC_ADDR_1_OFFSET KS8842_MACAR1_P
+#define KS8842_MAC_ADDR_0_OFFSET (KS8842_MAC_ADDR_1_OFFSET + 1)
+#define KS8842_MAC_ADDR_3_OFFSET KS8842_MACAR2_P
+#define KS8842_MAC_ADDR_2_OFFSET (KS8842_MAC_ADDR_3_OFFSET + 1)
+#define KS8842_MAC_ADDR_5_OFFSET KS8842_MACAR3_P
+#define KS8842_MAC_ADDR_4_OFFSET (KS8842_MAC_ADDR_5_OFFSET + 1)
+
+/* TOSR1 */
+#define KS8842_TOSR1_P 0x0480
+#define KS8842_TOSR2_P 0x0482
+#define KS8842_TOSR3_P 0x0484
+#define KS8842_TOSR4_P 0x0486
+#define KS8842_TOSR5_P 0x0488
+#define KS8842_TOSR6_P 0x048A
+#define KS8842_TOSR7_P 0x0490
+#define KS8842_TOSR8_P 0x0492
+#define KS8842_TOS_1_OFFSET KS8842_TOSR1_P
+#define KS8842_TOS_2_OFFSET KS8842_TOSR2_P
+#define KS8842_TOS_3_OFFSET KS8842_TOSR3_P
+#define KS8842_TOS_4_OFFSET KS8842_TOSR4_P
+#define KS8842_TOS_5_OFFSET KS8842_TOSR5_P
+#define KS8842_TOS_6_OFFSET KS8842_TOSR6_P
+
+#define KS8842_TOS_7_OFFSET KS8842_TOSR7_P
+#define KS8842_TOS_8_OFFSET KS8842_TOSR8_P
+
+/* P1CR1 */
+#define KS8842_P1CR1_P 0x0500
+#define KS8842_P1CR2_P 0x0502
+#define KS8842_P1VIDR_P 0x0504
+#define KS8842_P1CR3_P 0x0506
+#define KS8842_P1IRCR_P 0x0508
+#define KS8842_P1ERCR_P 0x050A
+#define KS884X_P1SCSLMD_P 0x0510
+#define KS884X_P1CR4_P 0x0512
+#define KS884X_P1SR_P 0x0514
+
+/* P2CR1 */
+#define KS8842_P2CR1_P 0x0520
+#define KS8842_P2CR2_P 0x0522
+#define KS8842_P2VIDR_P 0x0524
+#define KS8842_P2CR3_P 0x0526
+#define KS8842_P2IRCR_P 0x0528
+#define KS8842_P2ERCR_P 0x052A
+#define KS884X_P2SCSLMD_P 0x0530
+#define KS884X_P2CR4_P 0x0532
+#define KS884X_P2SR_P 0x0534
+
+/* P3CR1 */
+#define KS8842_P3CR1_P 0x0540
+#define KS8842_P3CR2_P 0x0542
+#define KS8842_P3VIDR_P 0x0544
+#define KS8842_P3CR3_P 0x0546
+#define KS8842_P3IRCR_P 0x0548
+#define KS8842_P3ERCR_P 0x054A
+
+#define KS8842_PORT_1_CTRL_1 KS8842_P1CR1_P
+#define KS8842_PORT_2_CTRL_1 KS8842_P2CR1_P
+#define KS8842_PORT_3_CTRL_1 KS8842_P3CR1_P
+
+#define PORT_CTRL_ADDR(port, addr) \
+ (addr = KS8842_PORT_1_CTRL_1 + (port) * \
+ (KS8842_PORT_2_CTRL_1 - KS8842_PORT_1_CTRL_1))
+
+#define KS8842_PORT_CTRL_1_OFFSET 0x00
+
+#define PORT_BROADCAST_STORM 0x0080
+#define PORT_DIFFSERV_ENABLE 0x0040
+#define PORT_802_1P_ENABLE 0x0020
+#define PORT_BASED_PRIORITY_MASK 0x0018
+#define PORT_BASED_PRIORITY_BASE 0x0003
+#define PORT_BASED_PRIORITY_SHIFT 3
+#define PORT_BASED_PRIORITY_0 0x0000
+#define PORT_BASED_PRIORITY_1 0x0008
+#define PORT_BASED_PRIORITY_2 0x0010
+#define PORT_BASED_PRIORITY_3 0x0018
+#define PORT_INSERT_TAG 0x0004
+#define PORT_REMOVE_TAG 0x0002
+#define PORT_PRIO_QUEUE_ENABLE 0x0001
+
+#define KS8842_PORT_CTRL_2_OFFSET 0x02
+
+#define PORT_INGRESS_VLAN_FILTER 0x4000
+#define PORT_DISCARD_NON_VID 0x2000
+#define PORT_FORCE_FLOW_CTRL 0x1000
+#define PORT_BACK_PRESSURE 0x0800
+#define PORT_TX_ENABLE 0x0400
+#define PORT_RX_ENABLE 0x0200
+#define PORT_LEARN_DISABLE 0x0100
+#define PORT_MIRROR_SNIFFER 0x0080
+#define PORT_MIRROR_RX 0x0040
+#define PORT_MIRROR_TX 0x0020
+#define PORT_USER_PRIORITY_CEILING 0x0008
+#define PORT_VLAN_MEMBERSHIP 0x0007
+
+#define KS8842_PORT_CTRL_VID_OFFSET 0x04
+
+#define PORT_DEFAULT_VID 0x0001
+
+#define KS8842_PORT_CTRL_3_OFFSET 0x06
+
+#define PORT_INGRESS_LIMIT_MODE 0x000C
+#define PORT_INGRESS_ALL 0x0000
+#define PORT_INGRESS_UNICAST 0x0004
+#define PORT_INGRESS_MULTICAST 0x0008
+#define PORT_INGRESS_BROADCAST 0x000C
+#define PORT_COUNT_IFG 0x0002
+#define PORT_COUNT_PREAMBLE 0x0001
+
+#define KS8842_PORT_IN_RATE_OFFSET 0x08
+#define KS8842_PORT_OUT_RATE_OFFSET 0x0A
+
+#define PORT_PRIORITY_RATE 0x0F
+#define PORT_PRIORITY_RATE_SHIFT 4
+
+#define KS884X_PORT_LINK_MD 0x10
+
+#define PORT_CABLE_10M_SHORT 0x8000
+#define PORT_CABLE_DIAG_RESULT 0x6000
+#define PORT_CABLE_STAT_NORMAL 0x0000
+#define PORT_CABLE_STAT_OPEN 0x2000
+#define PORT_CABLE_STAT_SHORT 0x4000
+#define PORT_CABLE_STAT_FAILED 0x6000
+#define PORT_START_CABLE_DIAG 0x1000
+#define PORT_FORCE_LINK 0x0800
+#define PORT_POWER_SAVING_DISABLE 0x0400
+#define PORT_PHY_REMOTE_LOOPBACK 0x0200
+#define PORT_CABLE_FAULT_COUNTER 0x01FF
+
+#define KS884X_PORT_CTRL_4_OFFSET 0x12
+
+#define PORT_LED_OFF 0x8000
+#define PORT_TX_DISABLE 0x4000
+#define PORT_AUTO_NEG_RESTART 0x2000
+#define PORT_REMOTE_FAULT_DISABLE 0x1000
+#define PORT_POWER_DOWN 0x0800
+#define PORT_AUTO_MDIX_DISABLE 0x0400
+#define PORT_FORCE_MDIX 0x0200
+#define PORT_LOOPBACK 0x0100
+#define PORT_AUTO_NEG_ENABLE 0x0080
+#define PORT_FORCE_100_MBIT 0x0040
+#define PORT_FORCE_FULL_DUPLEX 0x0020
+#define PORT_AUTO_NEG_SYM_PAUSE 0x0010
+#define PORT_AUTO_NEG_100BTX_FD 0x0008
+#define PORT_AUTO_NEG_100BTX 0x0004
+#define PORT_AUTO_NEG_10BT_FD 0x0002
+#define PORT_AUTO_NEG_10BT 0x0001
+
+#define KS884X_PORT_STATUS_OFFSET 0x14
+
+#define PORT_HP_MDIX 0x8000
+#define PORT_REVERSED_POLARITY 0x2000
+#define PORT_RX_FLOW_CTRL 0x0800
+#define PORT_TX_FLOW_CTRL 0x1000
+#define PORT_STATUS_SPEED_100MBIT 0x0400
+#define PORT_STATUS_FULL_DUPLEX 0x0200
+#define PORT_REMOTE_FAULT 0x0100
+#define PORT_MDIX_STATUS 0x0080
+#define PORT_AUTO_NEG_COMPLETE 0x0040
+#define PORT_STATUS_LINK_GOOD 0x0020
+#define PORT_REMOTE_SYM_PAUSE 0x0010
+#define PORT_REMOTE_100BTX_FD 0x0008
+#define PORT_REMOTE_100BTX 0x0004
+#define PORT_REMOTE_10BT_FD 0x0002
+#define PORT_REMOTE_10BT 0x0001
+
+/*
+#define STATIC_MAC_TABLE_ADDR 00-0000FFFF-FFFFFFFF
+#define STATIC_MAC_TABLE_FWD_PORTS 00-00070000-00000000
+#define STATIC_MAC_TABLE_VALID 00-00080000-00000000
+#define STATIC_MAC_TABLE_OVERRIDE 00-00100000-00000000
+#define STATIC_MAC_TABLE_USE_FID 00-00200000-00000000
+#define STATIC_MAC_TABLE_FID 00-03C00000-00000000
+*/
+
+#define STATIC_MAC_TABLE_ADDR 0x0000FFFF
+#define STATIC_MAC_TABLE_FWD_PORTS 0x00070000
+#define STATIC_MAC_TABLE_VALID 0x00080000
+#define STATIC_MAC_TABLE_OVERRIDE 0x00100000
+#define STATIC_MAC_TABLE_USE_FID 0x00200000
+#define STATIC_MAC_TABLE_FID 0x03C00000
+
+#define STATIC_MAC_FWD_PORTS_SHIFT 16
+#define STATIC_MAC_FID_SHIFT 22
+
+/*
+#define VLAN_TABLE_VID 00-00000000-00000FFF
+#define VLAN_TABLE_FID 00-00000000-0000F000
+#define VLAN_TABLE_MEMBERSHIP 00-00000000-00070000
+#define VLAN_TABLE_VALID 00-00000000-00080000
+*/
+
+#define VLAN_TABLE_VID 0x00000FFF
+#define VLAN_TABLE_FID 0x0000F000
+#define VLAN_TABLE_MEMBERSHIP 0x00070000
+#define VLAN_TABLE_VALID 0x00080000
+
+#define VLAN_TABLE_FID_SHIFT 12
+#define VLAN_TABLE_MEMBERSHIP_SHIFT 16
+
+/*
+#define DYNAMIC_MAC_TABLE_ADDR 00-0000FFFF-FFFFFFFF
+#define DYNAMIC_MAC_TABLE_FID 00-000F0000-00000000
+#define DYNAMIC_MAC_TABLE_SRC_PORT 00-00300000-00000000
+#define DYNAMIC_MAC_TABLE_TIMESTAMP 00-00C00000-00000000
+#define DYNAMIC_MAC_TABLE_ENTRIES 03-FF000000-00000000
+#define DYNAMIC_MAC_TABLE_MAC_EMPTY 04-00000000-00000000
+#define DYNAMIC_MAC_TABLE_RESERVED 78-00000000-00000000
+#define DYNAMIC_MAC_TABLE_NOT_READY 80-00000000-00000000
+*/
+
+#define DYNAMIC_MAC_TABLE_ADDR 0x0000FFFF
+#define DYNAMIC_MAC_TABLE_FID 0x000F0000
+#define DYNAMIC_MAC_TABLE_SRC_PORT 0x00300000
+#define DYNAMIC_MAC_TABLE_TIMESTAMP 0x00C00000
+#define DYNAMIC_MAC_TABLE_ENTRIES 0xFF000000
+
+#define DYNAMIC_MAC_TABLE_ENTRIES_H 0x03
+#define DYNAMIC_MAC_TABLE_MAC_EMPTY 0x04
+#define DYNAMIC_MAC_TABLE_RESERVED 0x78
+#define DYNAMIC_MAC_TABLE_NOT_READY 0x80
+
+#define DYNAMIC_MAC_FID_SHIFT 16
+#define DYNAMIC_MAC_SRC_PORT_SHIFT 20
+#define DYNAMIC_MAC_TIMESTAMP_SHIFT 22
+#define DYNAMIC_MAC_ENTRIES_SHIFT 24
+#define DYNAMIC_MAC_ENTRIES_H_SHIFT 8
+
+/*
+#define MIB_COUNTER_VALUE 00-00000000-3FFFFFFF
+#define MIB_COUNTER_VALID 00-00000000-40000000
+#define MIB_COUNTER_OVERFLOW 00-00000000-80000000
+*/
+
+#define MIB_COUNTER_VALUE 0x3FFFFFFF
+#define MIB_COUNTER_VALID 0x40000000
+#define MIB_COUNTER_OVERFLOW 0x80000000
+
+#define MIB_PACKET_DROPPED 0x0000FFFF
+
+#define KS_MIB_PACKET_DROPPED_TX_0 0x100
+#define KS_MIB_PACKET_DROPPED_TX_1 0x101
+#define KS_MIB_PACKET_DROPPED_TX 0x102
+#define KS_MIB_PACKET_DROPPED_RX_0 0x103
+#define KS_MIB_PACKET_DROPPED_RX_1 0x104
+#define KS_MIB_PACKET_DROPPED_RX 0x105
+
+/* Change default LED mode. */
+#define SET_DEFAULT_LED LED_SPEED_DUPLEX_ACT
+
+#define MAC_ADDR_LEN 6
+#define MAC_ADDR_ORDER(i) (MAC_ADDR_LEN - 1 - (i))
+
+#define MAX_ETHERNET_BODY_SIZE 1500
+#define ETHERNET_HEADER_SIZE 14
+
+#define MAX_ETHERNET_PACKET_SIZE \
+ (MAX_ETHERNET_BODY_SIZE + ETHERNET_HEADER_SIZE)
+
+#define REGULAR_RX_BUF_SIZE (MAX_ETHERNET_PACKET_SIZE + 4)
+#define MAX_RX_BUF_SIZE (1912 + 4)
+
+#define ADDITIONAL_ENTRIES 16
+#define MAX_MULTICAST_LIST 32
+
+#define HW_MULTICAST_SIZE 8
+
+#define HW_TO_DEV_PORT(port) (port - 1)
+
+enum {
+ media_connected,
+ media_disconnected
+};
+
+enum {
+ OID_COUNTER_UNKOWN,
+
+ OID_COUNTER_FIRST,
+
+ /* total transmit errors */
+ OID_COUNTER_XMIT_ERROR,
+
+ /* total receive errors */
+ OID_COUNTER_RCV_ERROR,
+
+ OID_COUNTER_LAST
+};
+
+/*
+ * Hardware descriptor definitions
+ */
+
+#define DESC_ALIGNMENT 16
+#define BUFFER_ALIGNMENT 8
+
+#define NUM_OF_RX_DESC 64
+#define NUM_OF_TX_DESC 64
+
+#define KS_DESC_RX_FRAME_LEN 0x000007FF
+#define KS_DESC_RX_FRAME_TYPE 0x00008000
+#define KS_DESC_RX_ERROR_CRC 0x00010000
+#define KS_DESC_RX_ERROR_RUNT 0x00020000
+#define KS_DESC_RX_ERROR_TOO_LONG 0x00040000
+#define KS_DESC_RX_ERROR_PHY 0x00080000
+#define KS884X_DESC_RX_PORT_MASK 0x00300000
+#define KS_DESC_RX_MULTICAST 0x01000000
+#define KS_DESC_RX_ERROR 0x02000000
+#define KS_DESC_RX_ERROR_CSUM_UDP 0x04000000
+#define KS_DESC_RX_ERROR_CSUM_TCP 0x08000000
+#define KS_DESC_RX_ERROR_CSUM_IP 0x10000000
+#define KS_DESC_RX_LAST 0x20000000
+#define KS_DESC_RX_FIRST 0x40000000
+#define KS_DESC_RX_ERROR_COND \
+ (KS_DESC_RX_ERROR_CRC | \
+ KS_DESC_RX_ERROR_RUNT | \
+ KS_DESC_RX_ERROR_PHY | \
+ KS_DESC_RX_ERROR_TOO_LONG)
+
+#define KS_DESC_HW_OWNED 0x80000000
+
+#define KS_DESC_BUF_SIZE 0x000007FF
+#define KS884X_DESC_TX_PORT_MASK 0x00300000
+#define KS_DESC_END_OF_RING 0x02000000
+#define KS_DESC_TX_CSUM_GEN_UDP 0x04000000
+#define KS_DESC_TX_CSUM_GEN_TCP 0x08000000
+#define KS_DESC_TX_CSUM_GEN_IP 0x10000000
+#define KS_DESC_TX_LAST 0x20000000
+#define KS_DESC_TX_FIRST 0x40000000
+#define KS_DESC_TX_INTERRUPT 0x80000000
+
+#define KS_DESC_PORT_SHIFT 20
+
+#define KS_DESC_RX_MASK (KS_DESC_BUF_SIZE)
+
+#define KS_DESC_TX_MASK \
+ (KS_DESC_TX_INTERRUPT | \
+ KS_DESC_TX_FIRST | \
+ KS_DESC_TX_LAST | \
+ KS_DESC_TX_CSUM_GEN_IP | \
+ KS_DESC_TX_CSUM_GEN_TCP | \
+ KS_DESC_TX_CSUM_GEN_UDP | \
+ KS_DESC_BUF_SIZE)
+
+struct ksz_desc_rx_stat {
+#ifdef __BIG_ENDIAN_BITFIELD
+ u32 hw_owned:1;
+ u32 first_desc:1;
+ u32 last_desc:1;
+ u32 csum_err_ip:1;
+ u32 csum_err_tcp:1;
+ u32 csum_err_udp:1;
+ u32 error:1;
+ u32 multicast:1;
+ u32 src_port:4;
+ u32 err_phy:1;
+ u32 err_too_long:1;
+ u32 err_runt:1;
+ u32 err_crc:1;
+ u32 frame_type:1;
+ u32 reserved1:4;
+ u32 frame_len:11;
+#else
+ u32 frame_len:11;
+ u32 reserved1:4;
+ u32 frame_type:1;
+ u32 err_crc:1;
+ u32 err_runt:1;
+ u32 err_too_long:1;
+ u32 err_phy:1;
+ u32 src_port:4;
+ u32 multicast:1;
+ u32 error:1;
+ u32 csum_err_udp:1;
+ u32 csum_err_tcp:1;
+ u32 csum_err_ip:1;
+ u32 last_desc:1;
+ u32 first_desc:1;
+ u32 hw_owned:1;
+#endif
+};
+
+struct ksz_desc_tx_stat {
+#ifdef __BIG_ENDIAN_BITFIELD
+ u32 hw_owned:1;
+ u32 reserved1:31;
+#else
+ u32 reserved1:31;
+ u32 hw_owned:1;
+#endif
+};
+
+struct ksz_desc_rx_buf {
+#ifdef __BIG_ENDIAN_BITFIELD
+ u32 reserved4:6;
+ u32 end_of_ring:1;
+ u32 reserved3:14;
+ u32 buf_size:11;
+#else
+ u32 buf_size:11;
+ u32 reserved3:14;
+ u32 end_of_ring:1;
+ u32 reserved4:6;
+#endif
+};
+
+struct ksz_desc_tx_buf {
+#ifdef __BIG_ENDIAN_BITFIELD
+ u32 intr:1;
+ u32 first_seg:1;
+ u32 last_seg:1;
+ u32 csum_gen_ip:1;
+ u32 csum_gen_tcp:1;
+ u32 csum_gen_udp:1;
+ u32 end_of_ring:1;
+ u32 reserved4:1;
+ u32 dest_port:4;
+ u32 reserved3:9;
+ u32 buf_size:11;
+#else
+ u32 buf_size:11;
+ u32 reserved3:9;
+ u32 dest_port:4;
+ u32 reserved4:1;
+ u32 end_of_ring:1;
+ u32 csum_gen_udp:1;
+ u32 csum_gen_tcp:1;
+ u32 csum_gen_ip:1;
+ u32 last_seg:1;
+ u32 first_seg:1;
+ u32 intr:1;
+#endif
+};
+
+union desc_stat {
+ struct ksz_desc_rx_stat rx;
+ struct ksz_desc_tx_stat tx;
+ u32 data;
+};
+
+union desc_buf {
+ struct ksz_desc_rx_buf rx;
+ struct ksz_desc_tx_buf tx;
+ u32 data;
+};
+
+/**
+ * struct ksz_hw_desc - Hardware descriptor data structure
+ * @ctrl: Descriptor control value.
+ * @buf: Descriptor buffer value.
+ * @addr: Physical address of memory buffer.
+ * @next: Pointer to next hardware descriptor.
+ */
+struct ksz_hw_desc {
+ union desc_stat ctrl;
+ union desc_buf buf;
+ u32 addr;
+ u32 next;
+};
+
+/**
+ * struct ksz_sw_desc - Software descriptor data structure
+ * @ctrl: Descriptor control value.
+ * @buf: Descriptor buffer value.
+ * @buf_size: Current buffers size value in hardware descriptor.
+ */
+struct ksz_sw_desc {
+ union desc_stat ctrl;
+ union desc_buf buf;
+ u32 buf_size;
+};
+
+/**
+ * struct ksz_dma_buf - OS dependent DMA buffer data structure
+ * @skb: Associated socket buffer.
+ * @dma: Associated physical DMA address.
+ * len: Actual len used.
+ */
+struct ksz_dma_buf {
+ struct sk_buff *skb;
+ dma_addr_t dma;
+ int len;
+};
+
+/**
+ * struct ksz_desc - Descriptor structure
+ * @phw: Hardware descriptor pointer to uncached physical memory.
+ * @sw: Cached memory to hold hardware descriptor values for
+ * manipulation.
+ * @dma_buf: Operating system dependent data structure to hold physical
+ * memory buffer allocation information.
+ */
+struct ksz_desc {
+ struct ksz_hw_desc *phw;
+ struct ksz_sw_desc sw;
+ struct ksz_dma_buf dma_buf;
+};
+
+#define DMA_BUFFER(desc) ((struct ksz_dma_buf *)(&(desc)->dma_buf))
+
+/**
+ * struct ksz_desc_info - Descriptor information data structure
+ * @ring: First descriptor in the ring.
+ * @cur: Current descriptor being manipulated.
+ * @ring_virt: First hardware descriptor in the ring.
+ * @ring_phys: The physical address of the first descriptor of the ring.
+ * @size: Size of hardware descriptor.
+ * @alloc: Number of descriptors allocated.
+ * @avail: Number of descriptors available for use.
+ * @last: Index for last descriptor released to hardware.
+ * @next: Index for next descriptor available for use.
+ * @mask: Mask for index wrapping.
+ */
+struct ksz_desc_info {
+ struct ksz_desc *ring;
+ struct ksz_desc *cur;
+ struct ksz_hw_desc *ring_virt;
+ u32 ring_phys;
+ int size;
+ int alloc;
+ int avail;
+ int last;
+ int next;
+ int mask;
+};
+
+/*
+ * KSZ8842 switch definitions
+ */
+
+enum {
+ TABLE_STATIC_MAC = 0,
+ TABLE_VLAN,
+ TABLE_DYNAMIC_MAC,
+ TABLE_MIB
+};
+
+#define LEARNED_MAC_TABLE_ENTRIES 1024
+#define STATIC_MAC_TABLE_ENTRIES 8
+
+/**
+ * struct ksz_mac_table - Static MAC table data structure
+ * @mac_addr: MAC address to filter.
+ * @vid: VID value.
+ * @fid: FID value.
+ * @ports: Port membership.
+ * @override: Override setting.
+ * @use_fid: FID use setting.
+ * @valid: Valid setting indicating the entry is being used.
+ */
+struct ksz_mac_table {
+ u8 mac_addr[MAC_ADDR_LEN];
+ u16 vid;
+ u8 fid;
+ u8 ports;
+ u8 override:1;
+ u8 use_fid:1;
+ u8 valid:1;
+};
+
+#define VLAN_TABLE_ENTRIES 16
+
+/**
+ * struct ksz_vlan_table - VLAN table data structure
+ * @vid: VID value.
+ * @fid: FID value.
+ * @member: Port membership.
+ */
+struct ksz_vlan_table {
+ u16 vid;
+ u8 fid;
+ u8 member;
+};
+
+#define DIFFSERV_ENTRIES 64
+#define PRIO_802_1P_ENTRIES 8
+#define PRIO_QUEUES 4
+
+#define SWITCH_PORT_NUM 2
+#define TOTAL_PORT_NUM (SWITCH_PORT_NUM + 1)
+#define HOST_MASK (1 << SWITCH_PORT_NUM)
+#define PORT_MASK 7
+
+#define MAIN_PORT 0
+#define OTHER_PORT 1
+#define HOST_PORT SWITCH_PORT_NUM
+
+#define PORT_COUNTER_NUM 0x20
+#define TOTAL_PORT_COUNTER_NUM (PORT_COUNTER_NUM + 2)
+
+#define MIB_COUNTER_RX_LO_PRIORITY 0x00
+#define MIB_COUNTER_RX_HI_PRIORITY 0x01
+#define MIB_COUNTER_RX_UNDERSIZE 0x02
+#define MIB_COUNTER_RX_FRAGMENT 0x03
+#define MIB_COUNTER_RX_OVERSIZE 0x04
+#define MIB_COUNTER_RX_JABBER 0x05
+#define MIB_COUNTER_RX_SYMBOL_ERR 0x06
+#define MIB_COUNTER_RX_CRC_ERR 0x07
+#define MIB_COUNTER_RX_ALIGNMENT_ERR 0x08
+#define MIB_COUNTER_RX_CTRL_8808 0x09
+#define MIB_COUNTER_RX_PAUSE 0x0A
+#define MIB_COUNTER_RX_BROADCAST 0x0B
+#define MIB_COUNTER_RX_MULTICAST 0x0C
+#define MIB_COUNTER_RX_UNICAST 0x0D
+#define MIB_COUNTER_RX_OCTET_64 0x0E
+#define MIB_COUNTER_RX_OCTET_65_127 0x0F
+#define MIB_COUNTER_RX_OCTET_128_255 0x10
+#define MIB_COUNTER_RX_OCTET_256_511 0x11
+#define MIB_COUNTER_RX_OCTET_512_1023 0x12
+#define MIB_COUNTER_RX_OCTET_1024_1522 0x13
+#define MIB_COUNTER_TX_LO_PRIORITY 0x14
+#define MIB_COUNTER_TX_HI_PRIORITY 0x15
+#define MIB_COUNTER_TX_LATE_COLLISION 0x16
+#define MIB_COUNTER_TX_PAUSE 0x17
+#define MIB_COUNTER_TX_BROADCAST 0x18
+#define MIB_COUNTER_TX_MULTICAST 0x19
+#define MIB_COUNTER_TX_UNICAST 0x1A
+#define MIB_COUNTER_TX_DEFERRED 0x1B
+#define MIB_COUNTER_TX_TOTAL_COLLISION 0x1C
+#define MIB_COUNTER_TX_EXCESS_COLLISION 0x1D
+#define MIB_COUNTER_TX_SINGLE_COLLISION 0x1E
+#define MIB_COUNTER_TX_MULTI_COLLISION 0x1F
+
+#define MIB_COUNTER_RX_DROPPED_PACKET 0x20
+#define MIB_COUNTER_TX_DROPPED_PACKET 0x21
+
+/**
+ * struct ksz_port_mib - Port MIB data structure
+ * @cnt_ptr: Current pointer to MIB counter index.
+ * @link_down: Indication the link has just gone down.
+ * @state: Connection status of the port.
+ * @mib_start: The starting counter index. Some ports do not start at 0.
+ * @counter: 64-bit MIB counter value.
+ * @dropped: Temporary buffer to remember last read packet dropped values.
+ *
+ * MIB counters needs to be read periodically so that counters do not get
+ * overflowed and give incorrect values. A right balance is needed to
+ * satisfy this condition and not waste too much CPU time.
+ *
+ * It is pointless to read MIB counters when the port is disconnected. The
+ * @state provides the connection status so that MIB counters are read only
+ * when the port is connected. The @link_down indicates the port is just
+ * disconnected so that all MIB counters are read one last time to update the
+ * information.
+ */
+struct ksz_port_mib {
+ u8 cnt_ptr;
+ u8 link_down;
+ u8 state;
+ u8 mib_start;
+
+ u64 counter[TOTAL_PORT_COUNTER_NUM];
+ u32 dropped[2];
+};
+
+/**
+ * struct ksz_port_cfg - Port configuration data structure
+ * @vid: VID value.
+ * @member: Port membership.
+ * @port_prio: Port priority.
+ * @rx_rate: Receive priority rate.
+ * @tx_rate: Transmit priority rate.
+ * @stp_state: Current Spanning Tree Protocol state.
+ */
+struct ksz_port_cfg {
+ u16 vid;
+ u8 member;
+ u8 port_prio;
+ u32 rx_rate[PRIO_QUEUES];
+ u32 tx_rate[PRIO_QUEUES];
+ int stp_state;
+};
+
+/**
+ * struct ksz_switch - KSZ8842 switch data structure
+ * @mac_table: MAC table entries information.
+ * @vlan_table: VLAN table entries information.
+ * @port_cfg: Port configuration information.
+ * @diffserv: DiffServ priority settings. Possible values from 6-bit of ToS
+ * (bit7 ~ bit2) field.
+ * @p_802_1p: 802.1P priority settings. Possible values from 3-bit of 802.1p
+ * Tag priority field.
+ * @br_addr: Bridge address. Used for STP.
+ * @other_addr: Other MAC address. Used for multiple network device mode.
+ * @broad_per: Broadcast storm percentage.
+ * @member: Current port membership. Used for STP.
+ */
+struct ksz_switch {
+ struct ksz_mac_table mac_table[STATIC_MAC_TABLE_ENTRIES];
+ struct ksz_vlan_table vlan_table[VLAN_TABLE_ENTRIES];
+ struct ksz_port_cfg port_cfg[TOTAL_PORT_NUM];
+
+ u8 diffserv[DIFFSERV_ENTRIES];
+ u8 p_802_1p[PRIO_802_1P_ENTRIES];
+
+ u8 br_addr[MAC_ADDR_LEN];
+ u8 other_addr[MAC_ADDR_LEN];
+
+ u8 broad_per;
+ u8 member;
+};
+
+#define TX_RATE_UNIT 10000
+
+/**
+ * struct ksz_port_info - Port information data structure
+ * @state: Connection status of the port.
+ * @tx_rate: Transmit rate divided by 10000 to get Mbit.
+ * @duplex: Duplex mode.
+ * @advertised: Advertised auto-negotiation setting. Used to determine link.
+ * @partner: Auto-negotiation partner setting. Used to determine link.
+ * @port_id: Port index to access actual hardware register.
+ * @pdev: Pointer to OS dependent network device.
+ */
+struct ksz_port_info {
+ uint state;
+ uint tx_rate;
+ u8 duplex;
+ u8 advertised;
+ u8 partner;
+ u8 port_id;
+ void *pdev;
+};
+
+#define MAX_TX_HELD_SIZE 52000
+
+/* Hardware features and bug fixes. */
+#define LINK_INT_WORKING (1 << 0)
+#define SMALL_PACKET_TX_BUG (1 << 1)
+#define HALF_DUPLEX_SIGNAL_BUG (1 << 2)
+#define RX_HUGE_FRAME (1 << 4)
+#define STP_SUPPORT (1 << 8)
+
+/* Software overrides. */
+#define PAUSE_FLOW_CTRL (1 << 0)
+#define FAST_AGING (1 << 1)
+
+/**
+ * struct ksz_hw - KSZ884X hardware data structure
+ * @io: Virtual address assigned.
+ * @ksz_switch: Pointer to KSZ8842 switch.
+ * @port_info: Port information.
+ * @port_mib: Port MIB information.
+ * @dev_count: Number of network devices this hardware supports.
+ * @dst_ports: Destination ports in switch for transmission.
+ * @id: Hardware ID. Used for display only.
+ * @mib_cnt: Number of MIB counters this hardware has.
+ * @mib_port_cnt: Number of ports with MIB counters.
+ * @tx_cfg: Cached transmit control settings.
+ * @rx_cfg: Cached receive control settings.
+ * @intr_mask: Current interrupt mask.
+ * @intr_set: Current interrup set.
+ * @intr_blocked: Interrupt blocked.
+ * @rx_desc_info: Receive descriptor information.
+ * @tx_desc_info: Transmit descriptor information.
+ * @tx_int_cnt: Transmit interrupt count. Used for TX optimization.
+ * @tx_int_mask: Transmit interrupt mask. Used for TX optimization.
+ * @tx_size: Transmit data size. Used for TX optimization.
+ * The maximum is defined by MAX_TX_HELD_SIZE.
+ * @perm_addr: Permanent MAC address.
+ * @override_addr: Overrided MAC address.
+ * @address: Additional MAC address entries.
+ * @addr_list_size: Additional MAC address list size.
+ * @mac_override: Indication of MAC address overrided.
+ * @promiscuous: Counter to keep track of promiscuous mode set.
+ * @all_multi: Counter to keep track of all multicast mode set.
+ * @multi_list: Multicast address entries.
+ * @multi_bits: Cached multicast hash table settings.
+ * @multi_list_size: Multicast address list size.
+ * @enabled: Indication of hardware enabled.
+ * @rx_stop: Indication of receive process stop.
+ * @features: Hardware features to enable.
+ * @overrides: Hardware features to override.
+ * @parent: Pointer to parent, network device private structure.
+ */
+struct ksz_hw {
+ void __iomem *io;
+
+ struct ksz_switch *ksz_switch;
+ struct ksz_port_info port_info[SWITCH_PORT_NUM];
+ struct ksz_port_mib port_mib[TOTAL_PORT_NUM];
+ int dev_count;
+ int dst_ports;
+ int id;
+ int mib_cnt;
+ int mib_port_cnt;
+
+ u32 tx_cfg;
+ u32 rx_cfg;
+ u32 intr_mask;
+ u32 intr_set;
+ uint intr_blocked;
+
+ struct ksz_desc_info rx_desc_info;
+ struct ksz_desc_info tx_desc_info;
+
+ int tx_int_cnt;
+ int tx_int_mask;
+ int tx_size;
+
+ u8 perm_addr[MAC_ADDR_LEN];
+ u8 override_addr[MAC_ADDR_LEN];
+ u8 address[ADDITIONAL_ENTRIES][MAC_ADDR_LEN];
+ u8 addr_list_size;
+ u8 mac_override;
+ u8 promiscuous;
+ u8 all_multi;
+ u8 multi_list[MAX_MULTICAST_LIST][MAC_ADDR_LEN];
+ u8 multi_bits[HW_MULTICAST_SIZE];
+ u8 multi_list_size;
+
+ u8 enabled;
+ u8 rx_stop;
+ u8 reserved2[1];
+
+ uint features;
+ uint overrides;
+
+ void *parent;
+};
+
+enum {
+ PHY_NO_FLOW_CTRL,
+ PHY_FLOW_CTRL,
+ PHY_TX_ONLY,
+ PHY_RX_ONLY
+};
+
+/**
+ * struct ksz_port - Virtual port data structure
+ * @duplex: Duplex mode setting. 1 for half duplex, 2 for full
+ * duplex, and 0 for auto, which normally results in full
+ * duplex.
+ * @speed: Speed setting. 10 for 10 Mbit, 100 for 100 Mbit, and
+ * 0 for auto, which normally results in 100 Mbit.
+ * @force_link: Force link setting. 0 for auto-negotiation, and 1 for
+ * force.
+ * @flow_ctrl: Flow control setting. PHY_NO_FLOW_CTRL for no flow
+ * control, and PHY_FLOW_CTRL for flow control.
+ * PHY_TX_ONLY and PHY_RX_ONLY are not supported for 100
+ * Mbit PHY.
+ * @first_port: Index of first port this port supports.
+ * @mib_port_cnt: Number of ports with MIB counters.
+ * @port_cnt: Number of ports this port supports.
+ * @counter: Port statistics counter.
+ * @hw: Pointer to hardware structure.
+ * @linked: Pointer to port information linked to this port.
+ */
+struct ksz_port {
+ u8 duplex;
+ u8 speed;
+ u8 force_link;
+ u8 flow_ctrl;
+
+ int first_port;
+ int mib_port_cnt;
+ int port_cnt;
+ u64 counter[OID_COUNTER_LAST];
+
+ struct ksz_hw *hw;
+ struct ksz_port_info *linked;
+};
+
+/**
+ * struct ksz_timer_info - Timer information data structure
+ * @timer: Kernel timer.
+ * @cnt: Running timer counter.
+ * @max: Number of times to run timer; -1 for infinity.
+ * @period: Timer period in jiffies.
+ */
+struct ksz_timer_info {
+ struct timer_list timer;
+ int cnt;
+ int max;
+ int period;
+};
+
+/**
+ * struct ksz_shared_mem - OS dependent shared memory data structure
+ * @dma_addr: Physical DMA address allocated.
+ * @alloc_size: Allocation size.
+ * @phys: Actual physical address used.
+ * @alloc_virt: Virtual address allocated.
+ * @virt: Actual virtual address used.
+ */
+struct ksz_shared_mem {
+ dma_addr_t dma_addr;
+ uint alloc_size;
+ uint phys;
+ u8 *alloc_virt;
+ u8 *virt;
+};
+
+/**
+ * struct ksz_counter_info - OS dependent counter information data structure
+ * @counter: Wait queue to wakeup after counters are read.
+ * @time: Next time in jiffies to read counter.
+ * @read: Indication of counters read in full or not.
+ */
+struct ksz_counter_info {
+ wait_queue_head_t counter;
+ unsigned long time;
+ int read;
+};
+
+/**
+ * struct dev_info - Network device information data structure
+ * @dev: Pointer to network device.
+ * @pdev: Pointer to PCI device.
+ * @hw: Hardware structure.
+ * @desc_pool: Physical memory used for descriptor pool.
+ * @hwlock: Spinlock to prevent hardware from accessing.
+ * @lock: Mutex lock to prevent device from accessing.
+ * @dev_rcv: Receive process function used.
+ * @last_skb: Socket buffer allocated for descriptor rx fragments.
+ * @skb_index: Buffer index for receiving fragments.
+ * @skb_len: Buffer length for receiving fragments.
+ * @mib_read: Workqueue to read MIB counters.
+ * @mib_timer_info: Timer to read MIB counters.
+ * @counter: Used for MIB reading.
+ * @mtu: Current MTU used. The default is REGULAR_RX_BUF_SIZE;
+ * the maximum is MAX_RX_BUF_SIZE.
+ * @opened: Counter to keep track of device open.
+ * @rx_tasklet: Receive processing tasklet.
+ * @tx_tasklet: Transmit processing tasklet.
+ * @wol_enable: Wake-on-LAN enable set by ethtool.
+ * @wol_support: Wake-on-LAN support used by ethtool.
+ * @pme_wait: Used for KSZ8841 power management.
+ */
+struct dev_info {
+ struct net_device *dev;
+ struct pci_dev *pdev;
+
+ struct ksz_hw hw;
+ struct ksz_shared_mem desc_pool;
+
+ spinlock_t hwlock;
+ struct mutex lock;
+
+ int (*dev_rcv)(struct dev_info *);
+
+ struct sk_buff *last_skb;
+ int skb_index;
+ int skb_len;
+
+ struct work_struct mib_read;
+ struct ksz_timer_info mib_timer_info;
+ struct ksz_counter_info counter[TOTAL_PORT_NUM];
+
+ int mtu;
+ int opened;
+
+ struct tasklet_struct rx_tasklet;
+ struct tasklet_struct tx_tasklet;
+
+ int wol_enable;
+ int wol_support;
+ unsigned long pme_wait;
+};
+
+/**
+ * struct dev_priv - Network device private data structure
+ * @adapter: Adapter device information.
+ * @port: Port information.
+ * @monitor_time_info: Timer to monitor ports.
+ * @proc_sem: Semaphore for proc accessing.
+ * @id: Device ID.
+ * @mii_if: MII interface information.
+ * @advertising: Temporary variable to store advertised settings.
+ * @msg_enable: The message flags controlling driver output.
+ * @media_state: The connection status of the device.
+ * @multicast: The all multicast state of the device.
+ * @promiscuous: The promiscuous state of the device.
+ */
+struct dev_priv {
+ struct dev_info *adapter;
+ struct ksz_port port;
+ struct ksz_timer_info monitor_timer_info;
+
+ struct semaphore proc_sem;
+ int id;
+
+ struct mii_if_info mii_if;
+ u32 advertising;
+
+ u32 msg_enable;
+ int media_state;
+ int multicast;
+ int promiscuous;
+};
+
+#define DRV_NAME "KSZ884X PCI"
+#define DEVICE_NAME "KSZ884x PCI"
+#define DRV_VERSION "1.0.0"
+#define DRV_RELDATE "Feb 8, 2010"
+
+static char version[] __devinitdata =
+ "Micrel " DEVICE_NAME " " DRV_VERSION " (" DRV_RELDATE ")";
+
+static u8 DEFAULT_MAC_ADDRESS[] = { 0x00, 0x10, 0xA1, 0x88, 0x42, 0x01 };
+
+/*
+ * Interrupt processing primary routines
+ */
+
+static inline void hw_ack_intr(struct ksz_hw *hw, uint interrupt)
+{
+ writel(interrupt, hw->io + KS884X_INTERRUPTS_STATUS);
+}
+
+static inline void hw_dis_intr(struct ksz_hw *hw)
+{
+ hw->intr_blocked = hw->intr_mask;
+ writel(0, hw->io + KS884X_INTERRUPTS_ENABLE);
+ hw->intr_set = readl(hw->io + KS884X_INTERRUPTS_ENABLE);
+}
+
+static inline void hw_set_intr(struct ksz_hw *hw, uint interrupt)
+{
+ hw->intr_set = interrupt;
+ writel(interrupt, hw->io + KS884X_INTERRUPTS_ENABLE);
+}
+
+static inline void hw_ena_intr(struct ksz_hw *hw)
+{
+ hw->intr_blocked = 0;
+ hw_set_intr(hw, hw->intr_mask);
+}
+
+static inline void hw_dis_intr_bit(struct ksz_hw *hw, uint bit)
+{
+ hw->intr_mask &= ~(bit);
+}
+
+static inline void hw_turn_off_intr(struct ksz_hw *hw, uint interrupt)
+{
+ u32 read_intr;
+
+ read_intr = readl(hw->io + KS884X_INTERRUPTS_ENABLE);
+ hw->intr_set = read_intr & ~interrupt;
+ writel(hw->intr_set, hw->io + KS884X_INTERRUPTS_ENABLE);
+ hw_dis_intr_bit(hw, interrupt);
+}
+
+/**
+ * hw_turn_on_intr - turn on specified interrupts
+ * @hw: The hardware instance.
+ * @bit: The interrupt bits to be on.
+ *
+ * This routine turns on the specified interrupts in the interrupt mask so that
+ * those interrupts will be enabled.
+ */
+static void hw_turn_on_intr(struct ksz_hw *hw, u32 bit)
+{
+ hw->intr_mask |= bit;
+
+ if (!hw->intr_blocked)
+ hw_set_intr(hw, hw->intr_mask);
+}
+
+static inline void hw_ena_intr_bit(struct ksz_hw *hw, uint interrupt)
+{
+ u32 read_intr;
+
+ read_intr = readl(hw->io + KS884X_INTERRUPTS_ENABLE);
+ hw->intr_set = read_intr | interrupt;
+ writel(hw->intr_set, hw->io + KS884X_INTERRUPTS_ENABLE);
+}
+
+static inline void hw_read_intr(struct ksz_hw *hw, uint *status)
+{
+ *status = readl(hw->io + KS884X_INTERRUPTS_STATUS);
+ *status = *status & hw->intr_set;
+}
+
+static inline void hw_restore_intr(struct ksz_hw *hw, uint interrupt)
+{
+ if (interrupt)
+ hw_ena_intr(hw);
+}
+
+/**
+ * hw_block_intr - block hardware interrupts
+ *
+ * This function blocks all interrupts of the hardware and returns the current
+ * interrupt enable mask so that interrupts can be restored later.
+ *
+ * Return the current interrupt enable mask.
+ */
+static uint hw_block_intr(struct ksz_hw *hw)
+{
+ uint interrupt = 0;
+
+ if (!hw->intr_blocked) {
+ hw_dis_intr(hw);
+ interrupt = hw->intr_blocked;
+ }
+ return interrupt;
+}
+
+/*
+ * Hardware descriptor routines
+ */
+
+static inline void reset_desc(struct ksz_desc *desc, union desc_stat status)
+{
+ status.rx.hw_owned = 0;
+ desc->phw->ctrl.data = cpu_to_le32(status.data);
+}
+
+static inline void release_desc(struct ksz_desc *desc)
+{
+ desc->sw.ctrl.tx.hw_owned = 1;
+ if (desc->sw.buf_size != desc->sw.buf.data) {
+ desc->sw.buf_size = desc->sw.buf.data;
+ desc->phw->buf.data = cpu_to_le32(desc->sw.buf.data);
+ }
+ desc->phw->ctrl.data = cpu_to_le32(desc->sw.ctrl.data);
+}
+
+static void get_rx_pkt(struct ksz_desc_info *info, struct ksz_desc **desc)
+{
+ *desc = &info->ring[info->last];
+ info->last++;
+ info->last &= info->mask;
+ info->avail--;
+ (*desc)->sw.buf.data &= ~KS_DESC_RX_MASK;
+}
+
+static inline void set_rx_buf(struct ksz_desc *desc, u32 addr)
+{
+ desc->phw->addr = cpu_to_le32(addr);
+}
+
+static inline void set_rx_len(struct ksz_desc *desc, u32 len)
+{
+ desc->sw.buf.rx.buf_size = len;
+}
+
+static inline void get_tx_pkt(struct ksz_desc_info *info,
+ struct ksz_desc **desc)
+{
+ *desc = &info->ring[info->next];
+ info->next++;
+ info->next &= info->mask;
+ info->avail--;
+ (*desc)->sw.buf.data &= ~KS_DESC_TX_MASK;
+}
+
+static inline void set_tx_buf(struct ksz_desc *desc, u32 addr)
+{
+ desc->phw->addr = cpu_to_le32(addr);
+}
+
+static inline void set_tx_len(struct ksz_desc *desc, u32 len)
+{
+ desc->sw.buf.tx.buf_size = len;
+}
+
+/* Switch functions */
+
+#define TABLE_READ 0x10
+#define TABLE_SEL_SHIFT 2
+
+#define HW_DELAY(hw, reg) \
+ do { \
+ u16 dummy; \
+ dummy = readw(hw->io + reg); \
+ } while (0)
+
+/**
+ * sw_r_table - read 4 bytes of data from switch table
+ * @hw: The hardware instance.
+ * @table: The table selector.
+ * @addr: The address of the table entry.
+ * @data: Buffer to store the read data.
+ *
+ * This routine reads 4 bytes of data from the table of the switch.
+ * Hardware interrupts are disabled to minimize corruption of read data.
+ */
+static void sw_r_table(struct ksz_hw *hw, int table, u16 addr, u32 *data)
+{
+ u16 ctrl_addr;
+ uint interrupt;
+
+ ctrl_addr = (((table << TABLE_SEL_SHIFT) | TABLE_READ) << 8) | addr;
+
+ interrupt = hw_block_intr(hw);
+
+ writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
+ HW_DELAY(hw, KS884X_IACR_OFFSET);
+ *data = readl(hw->io + KS884X_ACC_DATA_0_OFFSET);
+
+ hw_restore_intr(hw, interrupt);
+}
+
+/**
+ * sw_w_table_64 - write 8 bytes of data to the switch table
+ * @hw: The hardware instance.
+ * @table: The table selector.
+ * @addr: The address of the table entry.
+ * @data_hi: The high part of data to be written (bit63 ~ bit32).
+ * @data_lo: The low part of data to be written (bit31 ~ bit0).
+ *
+ * This routine writes 8 bytes of data to the table of the switch.
+ * Hardware interrupts are disabled to minimize corruption of written data.
+ */
+static void sw_w_table_64(struct ksz_hw *hw, int table, u16 addr, u32 data_hi,
+ u32 data_lo)
+{
+ u16 ctrl_addr;
+ uint interrupt;
+
+ ctrl_addr = ((table << TABLE_SEL_SHIFT) << 8) | addr;
+
+ interrupt = hw_block_intr(hw);
+
+ writel(data_hi, hw->io + KS884X_ACC_DATA_4_OFFSET);
+ writel(data_lo, hw->io + KS884X_ACC_DATA_0_OFFSET);
+
+ writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
+ HW_DELAY(hw, KS884X_IACR_OFFSET);
+
+ hw_restore_intr(hw, interrupt);
+}
+
+/**
+ * sw_w_sta_mac_table - write to the static MAC table
+ * @hw: The hardware instance.
+ * @addr: The address of the table entry.
+ * @mac_addr: The MAC address.
+ * @ports: The port members.
+ * @override: The flag to override the port receive/transmit settings.
+ * @valid: The flag to indicate entry is valid.
+ * @use_fid: The flag to indicate the FID is valid.
+ * @fid: The FID value.
+ *
+ * This routine writes an entry of the static MAC table of the switch. It
+ * calls sw_w_table_64() to write the data.
+ */
+static void sw_w_sta_mac_table(struct ksz_hw *hw, u16 addr, u8 *mac_addr,
+ u8 ports, int override, int valid, int use_fid, u8 fid)
+{
+ u32 data_hi;
+ u32 data_lo;
+
+ data_lo = ((u32) mac_addr[2] << 24) |
+ ((u32) mac_addr[3] << 16) |
+ ((u32) mac_addr[4] << 8) | mac_addr[5];
+ data_hi = ((u32) mac_addr[0] << 8) | mac_addr[1];
+ data_hi |= (u32) ports << STATIC_MAC_FWD_PORTS_SHIFT;
+
+ if (override)
+ data_hi |= STATIC_MAC_TABLE_OVERRIDE;
+ if (use_fid) {
+ data_hi |= STATIC_MAC_TABLE_USE_FID;
+ data_hi |= (u32) fid << STATIC_MAC_FID_SHIFT;
+ }
+ if (valid)
+ data_hi |= STATIC_MAC_TABLE_VALID;
+
+ sw_w_table_64(hw, TABLE_STATIC_MAC, addr, data_hi, data_lo);
+}
+
+/**
+ * sw_r_vlan_table - read from the VLAN table
+ * @hw: The hardware instance.
+ * @addr: The address of the table entry.
+ * @vid: Buffer to store the VID.
+ * @fid: Buffer to store the VID.
+ * @member: Buffer to store the port membership.
+ *
+ * This function reads an entry of the VLAN table of the switch. It calls
+ * sw_r_table() to get the data.
+ *
+ * Return 0 if the entry is valid; otherwise -1.
+ */
+static int sw_r_vlan_table(struct ksz_hw *hw, u16 addr, u16 *vid, u8 *fid,
+ u8 *member)
+{
+ u32 data;
+
+ sw_r_table(hw, TABLE_VLAN, addr, &data);
+ if (data & VLAN_TABLE_VALID) {
+ *vid = (u16)(data & VLAN_TABLE_VID);
+ *fid = (u8)((data & VLAN_TABLE_FID) >> VLAN_TABLE_FID_SHIFT);
+ *member = (u8)((data & VLAN_TABLE_MEMBERSHIP) >>
+ VLAN_TABLE_MEMBERSHIP_SHIFT);
+ return 0;
+ }
+ return -1;
+}
+
+/**
+ * port_r_mib_cnt - read MIB counter
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @addr: The address of the counter.
+ * @cnt: Buffer to store the counter.
+ *
+ * This routine reads a MIB counter of the port.
+ * Hardware interrupts are disabled to minimize corruption of read data.
+ */
+static void port_r_mib_cnt(struct ksz_hw *hw, int port, u16 addr, u64 *cnt)
+{
+ u32 data;
+ u16 ctrl_addr;
+ uint interrupt;
+ int timeout;
+
+ ctrl_addr = addr + PORT_COUNTER_NUM * port;
+
+ interrupt = hw_block_intr(hw);
+
+ ctrl_addr |= (((TABLE_MIB << TABLE_SEL_SHIFT) | TABLE_READ) << 8);
+ writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
+ HW_DELAY(hw, KS884X_IACR_OFFSET);
+
+ for (timeout = 100; timeout > 0; timeout--) {
+ data = readl(hw->io + KS884X_ACC_DATA_0_OFFSET);
+
+ if (data & MIB_COUNTER_VALID) {
+ if (data & MIB_COUNTER_OVERFLOW)
+ *cnt += MIB_COUNTER_VALUE + 1;
+ *cnt += data & MIB_COUNTER_VALUE;
+ break;
+ }
+ }
+
+ hw_restore_intr(hw, interrupt);
+}
+
+/**
+ * port_r_mib_pkt - read dropped packet counts
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @cnt: Buffer to store the receive and transmit dropped packet counts.
+ *
+ * This routine reads the dropped packet counts of the port.
+ * Hardware interrupts are disabled to minimize corruption of read data.
+ */
+static void port_r_mib_pkt(struct ksz_hw *hw, int port, u32 *last, u64 *cnt)
+{
+ u32 cur;
+ u32 data;
+ u16 ctrl_addr;
+ uint interrupt;
+ int index;
+
+ index = KS_MIB_PACKET_DROPPED_RX_0 + port;
+ do {
+ interrupt = hw_block_intr(hw);
+
+ ctrl_addr = (u16) index;
+ ctrl_addr |= (((TABLE_MIB << TABLE_SEL_SHIFT) | TABLE_READ)
+ << 8);
+ writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
+ HW_DELAY(hw, KS884X_IACR_OFFSET);
+ data = readl(hw->io + KS884X_ACC_DATA_0_OFFSET);
+
+ hw_restore_intr(hw, interrupt);
+
+ data &= MIB_PACKET_DROPPED;
+ cur = *last;
+ if (data != cur) {
+ *last = data;
+ if (data < cur)
+ data += MIB_PACKET_DROPPED + 1;
+ data -= cur;
+ *cnt += data;
+ }
+ ++last;
+ ++cnt;
+ index -= KS_MIB_PACKET_DROPPED_TX -
+ KS_MIB_PACKET_DROPPED_TX_0 + 1;
+ } while (index >= KS_MIB_PACKET_DROPPED_TX_0 + port);
+}
+
+/**
+ * port_r_cnt - read MIB counters periodically
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine is used to read the counters of the port periodically to avoid
+ * counter overflow. The hardware should be acquired first before calling this
+ * routine.
+ *
+ * Return non-zero when not all counters not read.
+ */
+static int port_r_cnt(struct ksz_hw *hw, int port)
+{
+ struct ksz_port_mib *mib = &hw->port_mib[port];
+
+ if (mib->mib_start < PORT_COUNTER_NUM)
+ while (mib->cnt_ptr < PORT_COUNTER_NUM) {
+ port_r_mib_cnt(hw, port, mib->cnt_ptr,
+ &mib->counter[mib->cnt_ptr]);
+ ++mib->cnt_ptr;
+ }
+ if (hw->mib_cnt > PORT_COUNTER_NUM)
+ port_r_mib_pkt(hw, port, mib->dropped,
+ &mib->counter[PORT_COUNTER_NUM]);
+ mib->cnt_ptr = 0;
+ return 0;
+}
+
+/**
+ * port_init_cnt - initialize MIB counter values
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine is used to initialize all counters to zero if the hardware
+ * cannot do it after reset.
+ */
+static void port_init_cnt(struct ksz_hw *hw, int port)
+{
+ struct ksz_port_mib *mib = &hw->port_mib[port];
+
+ mib->cnt_ptr = 0;
+ if (mib->mib_start < PORT_COUNTER_NUM)
+ do {
+ port_r_mib_cnt(hw, port, mib->cnt_ptr,
+ &mib->counter[mib->cnt_ptr]);
+ ++mib->cnt_ptr;
+ } while (mib->cnt_ptr < PORT_COUNTER_NUM);
+ if (hw->mib_cnt > PORT_COUNTER_NUM)
+ port_r_mib_pkt(hw, port, mib->dropped,
+ &mib->counter[PORT_COUNTER_NUM]);
+ memset((void *) mib->counter, 0, sizeof(u64) * TOTAL_PORT_COUNTER_NUM);
+ mib->cnt_ptr = 0;
+}
+
+/*
+ * Port functions
+ */
+
+/**
+ * port_chk - check port register bits
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the port register.
+ * @bits: The data bits to check.
+ *
+ * This function checks whether the specified bits of the port register are set
+ * or not.
+ *
+ * Return 0 if the bits are not set.
+ */
+static int port_chk(struct ksz_hw *hw, int port, int offset, u16 bits)
+{
+ u32 addr;
+ u16 data;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += offset;
+ data = readw(hw->io + addr);
+ return (data & bits) == bits;
+}
+
+/**
+ * port_cfg - set port register bits
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the port register.
+ * @bits: The data bits to set.
+ * @set: The flag indicating whether the bits are to be set or not.
+ *
+ * This routine sets or resets the specified bits of the port register.
+ */
+static void port_cfg(struct ksz_hw *hw, int port, int offset, u16 bits,
+ int set)
+{
+ u32 addr;
+ u16 data;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += offset;
+ data = readw(hw->io + addr);
+ if (set)
+ data |= bits;
+ else
+ data &= ~bits;
+ writew(data, hw->io + addr);
+}
+
+/**
+ * port_chk_shift - check port bit
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the register.
+ * @shift: Number of bits to shift.
+ *
+ * This function checks whether the specified port is set in the register or
+ * not.
+ *
+ * Return 0 if the port is not set.
+ */
+static int port_chk_shift(struct ksz_hw *hw, int port, u32 addr, int shift)
+{
+ u16 data;
+ u16 bit = 1 << port;
+
+ data = readw(hw->io + addr);
+ data >>= shift;
+ return (data & bit) == bit;
+}
+
+/**
+ * port_cfg_shift - set port bit
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the register.
+ * @shift: Number of bits to shift.
+ * @set: The flag indicating whether the port is to be set or not.
+ *
+ * This routine sets or resets the specified port in the register.
+ */
+static void port_cfg_shift(struct ksz_hw *hw, int port, u32 addr, int shift,
+ int set)
+{
+ u16 data;
+ u16 bits = 1 << port;
+
+ data = readw(hw->io + addr);
+ bits <<= shift;
+ if (set)
+ data |= bits;
+ else
+ data &= ~bits;
+ writew(data, hw->io + addr);
+}
+
+/**
+ * port_r8 - read byte from port register
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the port register.
+ * @data: Buffer to store the data.
+ *
+ * This routine reads a byte from the port register.
+ */
+static void port_r8(struct ksz_hw *hw, int port, int offset, u8 *data)
+{
+ u32 addr;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += offset;
+ *data = readb(hw->io + addr);
+}
+
+/**
+ * port_r16 - read word from port register.
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the port register.
+ * @data: Buffer to store the data.
+ *
+ * This routine reads a word from the port register.
+ */
+static void port_r16(struct ksz_hw *hw, int port, int offset, u16 *data)
+{
+ u32 addr;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += offset;
+ *data = readw(hw->io + addr);
+}
+
+/**
+ * port_w16 - write word to port register.
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @offset: The offset of the port register.
+ * @data: Data to write.
+ *
+ * This routine writes a word to the port register.
+ */
+static void port_w16(struct ksz_hw *hw, int port, int offset, u16 data)
+{
+ u32 addr;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += offset;
+ writew(data, hw->io + addr);
+}
+
+/**
+ * sw_chk - check switch register bits
+ * @hw: The hardware instance.
+ * @addr: The address of the switch register.
+ * @bits: The data bits to check.
+ *
+ * This function checks whether the specified bits of the switch register are
+ * set or not.
+ *
+ * Return 0 if the bits are not set.
+ */
+static int sw_chk(struct ksz_hw *hw, u32 addr, u16 bits)
+{
+ u16 data;
+
+ data = readw(hw->io + addr);
+ return (data & bits) == bits;
+}
+
+/**
+ * sw_cfg - set switch register bits
+ * @hw: The hardware instance.
+ * @addr: The address of the switch register.
+ * @bits: The data bits to set.
+ * @set: The flag indicating whether the bits are to be set or not.
+ *
+ * This function sets or resets the specified bits of the switch register.
+ */
+static void sw_cfg(struct ksz_hw *hw, u32 addr, u16 bits, int set)
+{
+ u16 data;
+
+ data = readw(hw->io + addr);
+ if (set)
+ data |= bits;
+ else
+ data &= ~bits;
+ writew(data, hw->io + addr);
+}
+
+/* Bandwidth */
+
+static inline void port_cfg_broad_storm(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_BROADCAST_STORM, set);
+}
+
+static inline int port_chk_broad_storm(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_BROADCAST_STORM);
+}
+
+/* Driver set switch broadcast storm protection at 10% rate. */
+#define BROADCAST_STORM_PROTECTION_RATE 10
+
+/* 148,800 frames * 67 ms / 100 */
+#define BROADCAST_STORM_VALUE 9969
+
+/**
+ * sw_cfg_broad_storm - configure broadcast storm threshold
+ * @hw: The hardware instance.
+ * @percent: Broadcast storm threshold in percent of transmit rate.
+ *
+ * This routine configures the broadcast storm threshold of the switch.
+ */
+static void sw_cfg_broad_storm(struct ksz_hw *hw, u8 percent)
+{
+ u16 data;
+ u32 value = ((u32) BROADCAST_STORM_VALUE * (u32) percent / 100);
+
+ if (value > BROADCAST_STORM_RATE)
+ value = BROADCAST_STORM_RATE;
+
+ data = readw(hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
+ data &= ~(BROADCAST_STORM_RATE_LO | BROADCAST_STORM_RATE_HI);
+ data |= ((value & 0x00FF) << 8) | ((value & 0xFF00) >> 8);
+ writew(data, hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
+}
+
+/**
+ * sw_get_board_storm - get broadcast storm threshold
+ * @hw: The hardware instance.
+ * @percent: Buffer to store the broadcast storm threshold percentage.
+ *
+ * This routine retrieves the broadcast storm threshold of the switch.
+ */
+static void sw_get_broad_storm(struct ksz_hw *hw, u8 *percent)
+{
+ int num;
+ u16 data;
+
+ data = readw(hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
+ num = (data & BROADCAST_STORM_RATE_HI);
+ num <<= 8;
+ num |= (data & BROADCAST_STORM_RATE_LO) >> 8;
+ num = (num * 100 + BROADCAST_STORM_VALUE / 2) / BROADCAST_STORM_VALUE;
+ *percent = (u8) num;
+}
+
+/**
+ * sw_dis_broad_storm - disable broadstorm
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine disables the broadcast storm limit function of the switch.
+ */
+static void sw_dis_broad_storm(struct ksz_hw *hw, int port)
+{
+ port_cfg_broad_storm(hw, port, 0);
+}
+
+/**
+ * sw_ena_broad_storm - enable broadcast storm
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine enables the broadcast storm limit function of the switch.
+ */
+static void sw_ena_broad_storm(struct ksz_hw *hw, int port)
+{
+ sw_cfg_broad_storm(hw, hw->ksz_switch->broad_per);
+ port_cfg_broad_storm(hw, port, 1);
+}
+
+/**
+ * sw_init_broad_storm - initialize broadcast storm
+ * @hw: The hardware instance.
+ *
+ * This routine initializes the broadcast storm limit function of the switch.
+ */
+static void sw_init_broad_storm(struct ksz_hw *hw)
+{
+ int port;
+
+ hw->ksz_switch->broad_per = 1;
+ sw_cfg_broad_storm(hw, hw->ksz_switch->broad_per);
+ for (port = 0; port < TOTAL_PORT_NUM; port++)
+ sw_dis_broad_storm(hw, port);
+ sw_cfg(hw, KS8842_SWITCH_CTRL_2_OFFSET, MULTICAST_STORM_DISABLE, 1);
+}
+
+/**
+ * hw_cfg_broad_storm - configure broadcast storm
+ * @hw: The hardware instance.
+ * @percent: Broadcast storm threshold in percent of transmit rate.
+ *
+ * This routine configures the broadcast storm threshold of the switch.
+ * It is called by user functions. The hardware should be acquired first.
+ */
+static void hw_cfg_broad_storm(struct ksz_hw *hw, u8 percent)
+{
+ if (percent > 100)
+ percent = 100;
+
+ sw_cfg_broad_storm(hw, percent);
+ sw_get_broad_storm(hw, &percent);
+ hw->ksz_switch->broad_per = percent;
+}
+
+/**
+ * sw_dis_prio_rate - disable switch priority rate
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine disables the priority rate function of the switch.
+ */
+static void sw_dis_prio_rate(struct ksz_hw *hw, int port)
+{
+ u32 addr;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += KS8842_PORT_IN_RATE_OFFSET;
+ writel(0, hw->io + addr);
+}
+
+/**
+ * sw_init_prio_rate - initialize switch prioirty rate
+ * @hw: The hardware instance.
+ *
+ * This routine initializes the priority rate function of the switch.
+ */
+static void sw_init_prio_rate(struct ksz_hw *hw)
+{
+ int port;
+ int prio;
+ struct ksz_switch *sw = hw->ksz_switch;
+
+ for (port = 0; port < TOTAL_PORT_NUM; port++) {
+ for (prio = 0; prio < PRIO_QUEUES; prio++) {
+ sw->port_cfg[port].rx_rate[prio] =
+ sw->port_cfg[port].tx_rate[prio] = 0;
+ }
+ sw_dis_prio_rate(hw, port);
+ }
+}
+
+/* Communication */
+
+static inline void port_cfg_back_pressure(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_BACK_PRESSURE, set);
+}
+
+static inline void port_cfg_force_flow_ctrl(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_FORCE_FLOW_CTRL, set);
+}
+
+static inline int port_chk_back_pressure(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_BACK_PRESSURE);
+}
+
+static inline int port_chk_force_flow_ctrl(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_FORCE_FLOW_CTRL);
+}
+
+/* Spanning Tree */
+
+static inline void port_cfg_dis_learn(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_LEARN_DISABLE, set);
+}
+
+static inline void port_cfg_rx(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_RX_ENABLE, set);
+}
+
+static inline void port_cfg_tx(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_TX_ENABLE, set);
+}
+
+static inline void sw_cfg_fast_aging(struct ksz_hw *hw, int set)
+{
+ sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET, SWITCH_FAST_AGING, set);
+}
+
+static inline void sw_flush_dyn_mac_table(struct ksz_hw *hw)
+{
+ if (!(hw->overrides & FAST_AGING)) {
+ sw_cfg_fast_aging(hw, 1);
+ mdelay(1);
+ sw_cfg_fast_aging(hw, 0);
+ }
+}
+
+/* VLAN */
+
+static inline void port_cfg_ins_tag(struct ksz_hw *hw, int p, int insert)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_INSERT_TAG, insert);
+}
+
+static inline void port_cfg_rmv_tag(struct ksz_hw *hw, int p, int remove)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_REMOVE_TAG, remove);
+}
+
+static inline int port_chk_ins_tag(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_INSERT_TAG);
+}
+
+static inline int port_chk_rmv_tag(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_REMOVE_TAG);
+}
+
+static inline void port_cfg_dis_non_vid(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_DISCARD_NON_VID, set);
+}
+
+static inline void port_cfg_in_filter(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_INGRESS_VLAN_FILTER, set);
+}
+
+static inline int port_chk_dis_non_vid(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_DISCARD_NON_VID);
+}
+
+static inline int port_chk_in_filter(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_INGRESS_VLAN_FILTER);
+}
+
+/* Mirroring */
+
+static inline void port_cfg_mirror_sniffer(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_MIRROR_SNIFFER, set);
+}
+
+static inline void port_cfg_mirror_rx(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_MIRROR_RX, set);
+}
+
+static inline void port_cfg_mirror_tx(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_MIRROR_TX, set);
+}
+
+static inline void sw_cfg_mirror_rx_tx(struct ksz_hw *hw, int set)
+{
+ sw_cfg(hw, KS8842_SWITCH_CTRL_2_OFFSET, SWITCH_MIRROR_RX_TX, set);
+}
+
+static void sw_init_mirror(struct ksz_hw *hw)
+{
+ int port;
+
+ for (port = 0; port < TOTAL_PORT_NUM; port++) {
+ port_cfg_mirror_sniffer(hw, port, 0);
+ port_cfg_mirror_rx(hw, port, 0);
+ port_cfg_mirror_tx(hw, port, 0);
+ }
+ sw_cfg_mirror_rx_tx(hw, 0);
+}
+
+static inline void sw_cfg_unk_def_deliver(struct ksz_hw *hw, int set)
+{
+ sw_cfg(hw, KS8842_SWITCH_CTRL_7_OFFSET,
+ SWITCH_UNK_DEF_PORT_ENABLE, set);
+}
+
+static inline int sw_cfg_chk_unk_def_deliver(struct ksz_hw *hw)
+{
+ return sw_chk(hw, KS8842_SWITCH_CTRL_7_OFFSET,
+ SWITCH_UNK_DEF_PORT_ENABLE);
+}
+
+static inline void sw_cfg_unk_def_port(struct ksz_hw *hw, int port, int set)
+{
+ port_cfg_shift(hw, port, KS8842_SWITCH_CTRL_7_OFFSET, 0, set);
+}
+
+static inline int sw_chk_unk_def_port(struct ksz_hw *hw, int port)
+{
+ return port_chk_shift(hw, port, KS8842_SWITCH_CTRL_7_OFFSET, 0);
+}
+
+/* Priority */
+
+static inline void port_cfg_diffserv(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_DIFFSERV_ENABLE, set);
+}
+
+static inline void port_cfg_802_1p(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_802_1P_ENABLE, set);
+}
+
+static inline void port_cfg_replace_vid(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_USER_PRIORITY_CEILING, set);
+}
+
+static inline void port_cfg_prio(struct ksz_hw *hw, int p, int set)
+{
+ port_cfg(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_PRIO_QUEUE_ENABLE, set);
+}
+
+static inline int port_chk_diffserv(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_DIFFSERV_ENABLE);
+}
+
+static inline int port_chk_802_1p(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_802_1P_ENABLE);
+}
+
+static inline int port_chk_replace_vid(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_2_OFFSET, PORT_USER_PRIORITY_CEILING);
+}
+
+static inline int port_chk_prio(struct ksz_hw *hw, int p)
+{
+ return port_chk(hw, p,
+ KS8842_PORT_CTRL_1_OFFSET, PORT_PRIO_QUEUE_ENABLE);
+}
+
+/**
+ * sw_dis_diffserv - disable switch DiffServ priority
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine disables the DiffServ priority function of the switch.
+ */
+static void sw_dis_diffserv(struct ksz_hw *hw, int port)
+{
+ port_cfg_diffserv(hw, port, 0);
+}
+
+/**
+ * sw_dis_802_1p - disable switch 802.1p priority
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine disables the 802.1p priority function of the switch.
+ */
+static void sw_dis_802_1p(struct ksz_hw *hw, int port)
+{
+ port_cfg_802_1p(hw, port, 0);
+}
+
+/**
+ * sw_cfg_replace_null_vid -
+ * @hw: The hardware instance.
+ * @set: The flag to disable or enable.
+ *
+ */
+static void sw_cfg_replace_null_vid(struct ksz_hw *hw, int set)
+{
+ sw_cfg(hw, KS8842_SWITCH_CTRL_3_OFFSET, SWITCH_REPLACE_NULL_VID, set);
+}
+
+/**
+ * sw_cfg_replace_vid - enable switch 802.10 priority re-mapping
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @set: The flag to disable or enable.
+ *
+ * This routine enables the 802.1p priority re-mapping function of the switch.
+ * That allows 802.1p priority field to be replaced with the port's default
+ * tag's priority value if the ingress packet's 802.1p priority has a higher
+ * priority than port's default tag's priority.
+ */
+static void sw_cfg_replace_vid(struct ksz_hw *hw, int port, int set)
+{
+ port_cfg_replace_vid(hw, port, set);
+}
+
+/**
+ * sw_cfg_port_based - configure switch port based priority
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @prio: The priority to set.
+ *
+ * This routine configures the port based priority of the switch.
+ */
+static void sw_cfg_port_based(struct ksz_hw *hw, int port, u8 prio)
+{
+ u16 data;
+
+ if (prio > PORT_BASED_PRIORITY_BASE)
+ prio = PORT_BASED_PRIORITY_BASE;
+
+ hw->ksz_switch->port_cfg[port].port_prio = prio;
+
+ port_r16(hw, port, KS8842_PORT_CTRL_1_OFFSET, &data);
+ data &= ~PORT_BASED_PRIORITY_MASK;
+ data |= prio << PORT_BASED_PRIORITY_SHIFT;
+ port_w16(hw, port, KS8842_PORT_CTRL_1_OFFSET, data);
+}
+
+/**
+ * sw_dis_multi_queue - disable transmit multiple queues
+ * @hw: The hardware instance.
+ * @port: The port index.
+ *
+ * This routine disables the transmit multiple queues selection of the switch
+ * port. Only single transmit queue on the port.
+ */
+static void sw_dis_multi_queue(struct ksz_hw *hw, int port)
+{
+ port_cfg_prio(hw, port, 0);
+}
+
+/**
+ * sw_init_prio - initialize switch priority
+ * @hw: The hardware instance.
+ *
+ * This routine initializes the switch QoS priority functions.
+ */
+static void sw_init_prio(struct ksz_hw *hw)
+{
+ int port;
+ int tos;
+ struct ksz_switch *sw = hw->ksz_switch;
+
+ /*
+ * Init all the 802.1p tag priority value to be assigned to different
+ * priority queue.
+ */
+ sw->p_802_1p[0] = 0;
+ sw->p_802_1p[1] = 0;
+ sw->p_802_1p[2] = 1;
+ sw->p_802_1p[3] = 1;
+ sw->p_802_1p[4] = 2;
+ sw->p_802_1p[5] = 2;
+ sw->p_802_1p[6] = 3;
+ sw->p_802_1p[7] = 3;
+
+ /*
+ * Init all the DiffServ priority value to be assigned to priority
+ * queue 0.
+ */
+ for (tos = 0; tos < DIFFSERV_ENTRIES; tos++)
+ sw->diffserv[tos] = 0;
+
+ /* All QoS functions disabled. */
+ for (port = 0; port < TOTAL_PORT_NUM; port++) {
+ sw_dis_multi_queue(hw, port);
+ sw_dis_diffserv(hw, port);
+ sw_dis_802_1p(hw, port);
+ sw_cfg_replace_vid(hw, port, 0);
+
+ sw->port_cfg[port].port_prio = 0;
+ sw_cfg_port_based(hw, port, sw->port_cfg[port].port_prio);
+ }
+ sw_cfg_replace_null_vid(hw, 0);
+}
+
+/**
+ * port_get_def_vid - get port default VID.
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @vid: Buffer to store the VID.
+ *
+ * This routine retrieves the default VID of the port.
+ */
+static void port_get_def_vid(struct ksz_hw *hw, int port, u16 *vid)
+{
+ u32 addr;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += KS8842_PORT_CTRL_VID_OFFSET;
+ *vid = readw(hw->io + addr);
+}
+
+/**
+ * sw_init_vlan - initialize switch VLAN
+ * @hw: The hardware instance.
+ *
+ * This routine initializes the VLAN function of the switch.
+ */
+static void sw_init_vlan(struct ksz_hw *hw)
+{
+ int port;
+ int entry;
+ struct ksz_switch *sw = hw->ksz_switch;
+
+ /* Read 16 VLAN entries from device's VLAN table. */
+ for (entry = 0; entry < VLAN_TABLE_ENTRIES; entry++) {
+ sw_r_vlan_table(hw, entry,
+ &sw->vlan_table[entry].vid,
+ &sw->vlan_table[entry].fid,
+ &sw->vlan_table[entry].member);
+ }
+
+ for (port = 0; port < TOTAL_PORT_NUM; port++) {
+ port_get_def_vid(hw, port, &sw->port_cfg[port].vid);
+ sw->port_cfg[port].member = PORT_MASK;
+ }
+}
+
+/**
+ * sw_cfg_port_base_vlan - configure port-based VLAN membership
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @member: The port-based VLAN membership.
+ *
+ * This routine configures the port-based VLAN membership of the port.
+ */
+static void sw_cfg_port_base_vlan(struct ksz_hw *hw, int port, u8 member)
+{
+ u32 addr;
+ u8 data;
+
+ PORT_CTRL_ADDR(port, addr);
+ addr += KS8842_PORT_CTRL_2_OFFSET;
+
+ data = readb(hw->io + addr);
+ data &= ~PORT_VLAN_MEMBERSHIP;
+ data |= (member & PORT_MASK);
+ writeb(data, hw->io + addr);
+
+ hw->ksz_switch->port_cfg[port].member = member;
+}
+
+/**
+ * sw_get_addr - get the switch MAC address.
+ * @hw: The hardware instance.
+ * @mac_addr: Buffer to store the MAC address.
+ *
+ * This function retrieves the MAC address of the switch.
+ */
+static inline void sw_get_addr(struct ksz_hw *hw, u8 *mac_addr)
+{
+ int i;
+
+ for (i = 0; i < 6; i += 2) {
+ mac_addr[i] = readb(hw->io + KS8842_MAC_ADDR_0_OFFSET + i);
+ mac_addr[1 + i] = readb(hw->io + KS8842_MAC_ADDR_1_OFFSET + i);
+ }
+}
+
+/**
+ * sw_set_addr - configure switch MAC address
+ * @hw: The hardware instance.
+ * @mac_addr: The MAC address.
+ *
+ * This function configures the MAC address of the switch.
+ */
+static void sw_set_addr(struct ksz_hw *hw, u8 *mac_addr)
+{
+ int i;
+
+ for (i = 0; i < 6; i += 2) {
+ writeb(mac_addr[i], hw->io + KS8842_MAC_ADDR_0_OFFSET + i);
+ writeb(mac_addr[1 + i], hw->io + KS8842_MAC_ADDR_1_OFFSET + i);
+ }
+}
+
+/**
+ * sw_set_global_ctrl - set switch global control
+ * @hw: The hardware instance.
+ *
+ * This routine sets the global control of the switch function.
+ */
+static void sw_set_global_ctrl(struct ksz_hw *hw)
+{
+ u16 data;
+
+ /* Enable switch MII flow control. */
+ data = readw(hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
+ data |= SWITCH_FLOW_CTRL;
+ writew(data, hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
+
+ data = readw(hw->io + KS8842_SWITCH_CTRL_1_OFFSET);
+
+ /* Enable aggressive back off algorithm in half duplex mode. */
+ data |= SWITCH_AGGR_BACKOFF;
+
+ /* Enable automatic fast aging when link changed detected. */
+ data |= SWITCH_AGING_ENABLE;
+ data |= SWITCH_LINK_AUTO_AGING;
+
+ if (hw->overrides & FAST_AGING)
+ data |= SWITCH_FAST_AGING;
+ else
+ data &= ~SWITCH_FAST_AGING;
+ writew(data, hw->io + KS8842_SWITCH_CTRL_1_OFFSET);
+
+ data = readw(hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
+
+ /* Enable no excessive collision drop. */
+ data |= NO_EXC_COLLISION_DROP;
+ writew(data, hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
+}
+
+enum {
+ STP_STATE_DISABLED = 0,
+ STP_STATE_LISTENING,
+ STP_STATE_LEARNING,
+ STP_STATE_FORWARDING,
+ STP_STATE_BLOCKED,
+ STP_STATE_SIMPLE
+};
+
+/**
+ * port_set_stp_state - configure port spanning tree state
+ * @hw: The hardware instance.
+ * @port: The port index.
+ * @state: The spanning tree state.
+ *
+ * This routine configures the spanning tree state of the port.
+ */
+static void port_set_stp_state(struct ksz_hw *hw, int port, int state)
+{
+ u16 data;
+
+ port_r16(hw, port, KS8842_PORT_CTRL_2_OFFSET, &data);
+ switch (state) {
+ case STP_STATE_DISABLED:
+ data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE);
+ data |= PORT_LEARN_DISABLE;
+ break;
+ case STP_STATE_LISTENING:
+/*
+ * No need to turn on transmit because of port direct mode.
+ * Turning on receive is required if static MAC table is not setup.
+ */
+ data &= ~PORT_TX_ENABLE;
+ data |= PORT_RX_ENABLE;
+ data |= PORT_LEARN_DISABLE;
+ break;
+ case STP_STATE_LEARNING:
+ data &= ~PORT_TX_ENABLE;
+ data |= PORT_RX_ENABLE;
+ data &= ~PORT_LEARN_DISABLE;
+ break;
+ case STP_STATE_FORWARDING:
+ data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+ data &= ~PORT_LEARN_DISABLE;
+ break;
+ case STP_STATE_BLOCKED:
+/*
+ * Need to setup static MAC table with override to keep receiving BPDU
+ * messages. See sw_init_stp routine.
+ */
+ data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE);
+ data |= PORT_LEARN_DISABLE;
+ break;
+ case STP_STATE_SIMPLE:
+ data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
+ data |= PORT_LEARN_DISABLE;
+ break;
+ }
+ port_w16(hw, port, KS8842_PORT_CTRL_2_OFFSET, data);
+ hw->ksz_switch->port_cfg[port].stp_state = state;
+}
+
+#define STP_ENTRY 0
+#define BROADCAST_ENTRY 1
+#define BRIDGE_ADDR_ENTRY 2
+#define IPV6_ADDR_ENTRY 3
+
+/**
+ * sw_clr_sta_mac_table - clear static MAC table
+ * @hw: The hardware instance.
+ *
+ * This routine clears the static MAC table.
+ */
+static void sw_clr_sta_mac_table(struct ksz_hw *hw)
+{
+ struct ksz_mac_table *entry;
+ int i;
+
+ for (i = 0; i < STATIC_MAC_TABLE_ENTRIES; i++) {
+ entry = &hw->ksz_switch->mac_table[i];
+ sw_w_sta_mac_table(hw, i,
+ entry->mac_addr, entry->ports,
+ entry->override, 0,
+ entry->use_fid, entry->fid);
+ }
+}
+
+/**
+ * sw_init_stp - initialize switch spanning tree support
+ * @hw: The hardware instance.
+ *
+ * This routine initializes the spanning tree support of the switch.
+ */
+static void sw_init_stp(struct ksz_hw *hw)
+{
+ struct ksz_mac_table *entry;
+
+ entry = &hw->ksz_switch->mac_table[STP_ENTRY];
+ entry->mac_addr[0] = 0x01;
+ entry->mac_addr[1] = 0x80;
+ entry->mac_addr[2] = 0xC2;
+ entry->mac_addr[3] = 0x00;
+ entry->mac_addr[4] = 0x00;
+ entry->mac_addr[5] = 0x00;
+ entry->ports = HOST_MASK;
+ entry->override = 1;
+ entry->valid = 1;
+ sw_w_sta_mac_table(hw, STP_ENTRY,
+ entry->mac_addr, entry->ports,
+ entry->override, entry->valid,
+ entry->use_fid, entry->fid);
+}
+
+/**
+ * sw_block_addr - block certain packets from the host port
+ * @hw: The hardware instance.
+ *
+ * This routine blocks certain packets from reaching to the host port.
+ */
+static void sw_block_addr(struct ksz_hw *hw)
+{
+ struct ksz_mac_table *entry;
+ int i;
+
+ for (i = BROADCAST_ENTRY; i <= IPV6_ADDR_ENTRY; i++) {
+ entry = &hw->ksz_switch->mac_table[i];
+ entry->valid = 0;
+ sw_w_sta_mac_table(hw, i,
+ entry->mac_addr, entry->ports,
+ entry->override, entry->valid,
+ entry->use_fid, entry->fid);
+ }
+}
+
+#define PHY_LINK_SUPPORT \
+ (PHY_AUTO_NEG_ASYM_PAUSE | \
+ PHY_AUTO_NEG_SYM_PAUSE | \
+ PHY_AUTO_NEG_100BT4 | \
+ PHY_AUTO_NEG_100BTX_FD | \
+ PHY_AUTO_NEG_100BTX | \
+ PHY_AUTO_NEG_10BT_FD | \
+ PHY_AUTO_NEG_10BT)
+
+static inline void hw_r_phy_ctrl(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_CTRL_OFFSET);
+}
+
+static inline void hw_w_phy_ctrl(struct ksz_hw *hw, int phy, u16 data)
+{
+ writew(data, hw->io + phy + KS884X_PHY_CTRL_OFFSET);
+}
+
+static inline void hw_r_phy_link_stat(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_STATUS_OFFSET);
+}
+
+static inline void hw_r_phy_auto_neg(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_AUTO_NEG_OFFSET);
+}
+
+static inline void hw_w_phy_auto_neg(struct ksz_hw *hw, int phy, u16 data)
+{
+ writew(data, hw->io + phy + KS884X_PHY_AUTO_NEG_OFFSET);
+}
+
+static inline void hw_r_phy_rem_cap(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_REMOTE_CAP_OFFSET);
+}
+
+static inline void hw_r_phy_crossover(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_CTRL_OFFSET);
+}
+
+static inline void hw_w_phy_crossover(struct ksz_hw *hw, int phy, u16 data)
+{
+ writew(data, hw->io + phy + KS884X_PHY_CTRL_OFFSET);
+}
+
+static inline void hw_r_phy_polarity(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_PHY_CTRL_OFFSET);
+}
+
+static inline void hw_w_phy_polarity(struct ksz_hw *hw, int phy, u16 data)
+{
+ writew(data, hw->io + phy + KS884X_PHY_PHY_CTRL_OFFSET);
+}
+
+static inline void hw_r_phy_link_md(struct ksz_hw *hw, int phy, u16 *data)
+{
+ *data = readw(hw->io + phy + KS884X_PHY_LINK_MD_OFFSET);
+}
+
+static inline void hw_w_phy_link_md(struct ksz_hw *hw, int phy, u16 data)
+{
+ writew(data, hw->io + phy + KS884X_PHY_LINK_MD_OFFSET);
+}
+
+/**
+ * hw_r_phy - read data from PHY register
+ * @hw: The hardware instance.
+ * @port: Port to read.
+ * @reg: PHY register to read.
+ * @val: Buffer to store the read data.
+ *
+ * This routine reads data from the PHY register.
+ */
+static void hw_r_phy(struct ksz_hw *hw, int port, u16 reg, u16 *val)
+{
+ int phy;
+
+ phy = KS884X_PHY_1_CTRL_OFFSET + port * PHY_CTRL_INTERVAL + reg;
+ *val = readw(hw->io + phy);
+}
+
+/**
+ * port_w_phy - write data to PHY register
+ * @hw: The hardware instance.
+ * @port: Port to write.
+ * @reg: PHY register to write.
+ * @val: Word data to write.
+ *
+ * This routine writes data to the PHY register.
+ */
+static void hw_w_phy(struct ksz_hw *hw, int port, u16 reg, u16 val)
+{
+ int phy;
+
+ phy = KS884X_PHY_1_CTRL_OFFSET + port * PHY_CTRL_INTERVAL + reg;
+ writew(val, hw->io + phy);
+}
+
+/*
+ * EEPROM access functions
+ */
+
+#define AT93C_CODE 0
+#define AT93C_WR_OFF 0x00
+#define AT93C_WR_ALL 0x10
+#define AT93C_ER_ALL 0x20
+#define AT93C_WR_ON 0x30
+
+#define AT93C_WRITE 1
+#define AT93C_READ 2
+#define AT93C_ERASE 3
+
+#define EEPROM_DELAY 4
+
+static inline void drop_gpio(struct ksz_hw *hw, u8 gpio)
+{
+ u16 data;
+
+ data = readw(hw->io + KS884X_EEPROM_CTRL_OFFSET);
+ data &= ~gpio;
+ writew(data, hw->io + KS884X_EEPROM_CTRL_OFFSET);
+}
+
+static inline void raise_gpio(struct ksz_hw *hw, u8 gpio)
+{
+ u16 data;
+
+ data = readw(hw->io + KS884X_EEPROM_CTRL_OFFSET);
+ data |= gpio;
+ writew(data, hw->io + KS884X_EEPROM_CTRL_OFFSET);
+}
+
+static inline u8 state_gpio(struct ksz_hw *hw, u8 gpio)
+{
+ u16 data;
+
+ data = readw(hw->io + KS884X_EEPROM_CTRL_OFFSET);
+ return (u8)(data & gpio);
+}
+
+static void eeprom_clk(struct ksz_hw *hw)
+{
+ raise_gpio(hw, EEPROM_SERIAL_CLOCK);
+ udelay(EEPROM_DELAY);
+ drop_gpio(hw, EEPROM_SERIAL_CLOCK);
+ udelay(EEPROM_DELAY);
+}
+
+static u16 spi_r(struct ksz_hw *hw)
+{
+ int i;
+ u16 temp = 0;
+
+ for (i = 15; i >= 0; i--) {
+ raise_gpio(hw, EEPROM_SERIAL_CLOCK);
+ udelay(EEPROM_DELAY);
+
+ temp |= (state_gpio(hw, EEPROM_DATA_IN)) ? 1 << i : 0;
+
+ drop_gpio(hw, EEPROM_SERIAL_CLOCK);
+ udelay(EEPROM_DELAY);
+ }
+ return temp;
+}
+
+static void spi_w(struct ksz_hw *hw, u16 data)
+{
+ int i;
+
+ for (i = 15; i >= 0; i--) {
+ (data & (0x01 << i)) ? raise_gpio(hw, EEPROM_DATA_OUT) :
+ drop_gpio(hw, EEPROM_DATA_OUT);
+ eeprom_clk(hw);
+ }
+}
+
+static void spi_reg(struct ksz_hw *hw, u8 data, u8 reg)
+{
+ int i;
+
+ /* Initial start bit */
+ raise_gpio(hw, EEPROM_DATA_OUT);
+ eeprom_clk(hw);
+
+ /* AT93C operation */
+ for (i = 1; i >= 0; i--) {
+ (data & (0x01 << i)) ? raise_gpio(hw, EEPROM_DATA_OUT) :
+ drop_gpio(hw, EEPROM_DATA_OUT);
+ eeprom_clk(hw);
+ }
+
+ /* Address location */
+ for (i = 5; i >= 0; i--) {
+ (reg & (0x01 << i)) ? raise_gpio(hw, EEPROM_DATA_OUT) :
+ drop_gpio(hw, EEPROM_DATA_OUT);
+ eeprom_clk(hw);
+ }
+}
+
+#define EEPROM_DATA_RESERVED 0
+#define EEPROM_DATA_MAC_ADDR_0 1
+#define EEPROM_DATA_MAC_ADDR_1 2
+#define EEPROM_DATA_MAC_ADDR_2 3
+#define EEPROM_DATA_SUBSYS_ID 4
+#define EEPROM_DATA_SUBSYS_VEN_ID 5
+#define EEPROM_DATA_PM_CAP 6
+
+/* User defined EEPROM data */
+#define EEPROM_DATA_OTHER_MAC_ADDR 9
+
+/**
+ * eeprom_read - read from AT93C46 EEPROM
+ * @hw: The hardware instance.
+ * @reg: The register offset.
+ *
+ * This function reads a word from the AT93C46 EEPROM.
+ *
+ * Return the data value.
+ */
+static u16 eeprom_read(struct ksz_hw *hw, u8 reg)
+{
+ u16 data;
+
+ raise_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
+
+ spi_reg(hw, AT93C_READ, reg);
+ data = spi_r(hw);
+
+ drop_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
+
+ return data;
+}
+
+/**
+ * eeprom_write - write to AT93C46 EEPROM
+ * @hw: The hardware instance.
+ * @reg: The register offset.
+ * @data: The data value.
+ *
+ * This procedure writes a word to the AT93C46 EEPROM.
+ */
+static void eeprom_write(struct ksz_hw *hw, u8 reg, u16 data)
+{
+ int timeout;
+
+ raise_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
+
+ /* Enable write. */
+ spi_reg(hw, AT93C_CODE, AT93C_WR_ON);
+ drop_gpio(hw, EEPROM_CHIP_SELECT);
+ udelay(1);
+
+ /* Erase the register. */
+ raise_gpio(hw, EEPROM_CHIP_SELECT);
+ spi_reg(hw, AT93C_ERASE, reg);
+ drop_gpio(hw, EEPROM_CHIP_SELECT);
+ udelay(1);
+
+ /* Check operation complete. */
+ raise_gpio(hw, EEPROM_CHIP_SELECT);
+ timeout = 8;
+ mdelay(2);
+ do {
+ mdelay(1);
+ } while (!state_gpio(hw, EEPROM_DATA_IN) && --timeout);
+ drop_gpio(hw, EEPROM_CHIP_SELECT);
+ udelay(1);
+
+ /* Write the register. */
+ raise_gpio(hw, EEPROM_CHIP_SELECT);
+ spi_reg(hw, AT93C_WRITE, reg);
+ spi_w(hw, data);
+ drop_gpio(hw, EEPROM_CHIP_SELECT);
+ udelay(1);
+
+ /* Check operation complete. */
+ raise_gpio(hw, EEPROM_CHIP_SELECT);
+ timeout = 8;
+ mdelay(2);
+ do {
+ mdelay(1);
+ } while (!state_gpio(hw, EEPROM_DATA_IN) && --timeout);
+ drop_gpio(hw, EEPROM_CHIP_SELECT);
+ udelay(1);
+
+ /* Disable write. */
+ raise_gpio(hw, EEPROM_CHIP_SELECT);
+ spi_reg(hw, AT93C_CODE, AT93C_WR_OFF);
+
+ drop_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
+}
+
+/*
+ * Link detection routines
+ */
+
+static u16 advertised_flow_ctrl(struct ksz_port *port, u16 ctrl)
+{
+ ctrl &= ~PORT_AUTO_NEG_SYM_PAUSE;
+ switch (port->flow_ctrl) {
+ case PHY_FLOW_CTRL:
+ ctrl |= PORT_AUTO_NEG_SYM_PAUSE;
+ break;
+ /* Not supported. */
+ case PHY_TX_ONLY:
+ case PHY_RX_ONLY:
+ default:
+ break;
+ }
+ return ctrl;
+}
+
+static void set_flow_ctrl(struct ksz_hw *hw, int rx, int tx)
+{
+ u32 rx_cfg;
+ u32 tx_cfg;
+
+ rx_cfg = hw->rx_cfg;
+ tx_cfg = hw->tx_cfg;
+ if (rx)
+ hw->rx_cfg |= DMA_RX_FLOW_ENABLE;
+ else
+ hw->rx_cfg &= ~DMA_RX_FLOW_ENABLE;
+ if (tx)
+ hw->tx_cfg |= DMA_TX_FLOW_ENABLE;
+ else
+ hw->tx_cfg &= ~DMA_TX_FLOW_ENABLE;
+ if (hw->enabled) {
+ if (rx_cfg != hw->rx_cfg)
+ writel(hw->rx_cfg, hw->io + KS_DMA_RX_CTRL);
+ if (tx_cfg != hw->tx_cfg)
+ writel(hw->tx_cfg, hw->io + KS_DMA_TX_CTRL);
+ }
+}
+
+static void determine_flow_ctrl(struct ksz_hw *hw, struct ksz_port *port,
+ u16 local, u16 remote)
+{
+ int rx;
+ int tx;
+
+ if (hw->overrides & PAUSE_FLOW_CTRL)
+ return;
+
+ rx = tx = 0;
+ if (port->force_link)
+ rx = tx = 1;
+ if (remote & PHY_AUTO_NEG_SYM_PAUSE) {
+ if (local & PHY_AUTO_NEG_SYM_PAUSE) {
+ rx = tx = 1;
+ } else if ((remote & PHY_AUTO_NEG_ASYM_PAUSE) &&
+ (local & PHY_AUTO_NEG_PAUSE) ==
+ PHY_AUTO_NEG_ASYM_PAUSE) {
+ tx = 1;
+ }
+ } else if (remote & PHY_AUTO_NEG_ASYM_PAUSE) {
+ if ((local & PHY_AUTO_NEG_PAUSE) == PHY_AUTO_NEG_PAUSE)
+ rx = 1;
+ }
+ if (!hw->ksz_switch)
+ set_flow_ctrl(hw, rx, tx);
+}
+
+static inline void port_cfg_change(struct ksz_hw *hw, struct ksz_port *port,
+ struct ksz_port_info *info, u16 link_status)
+{
+ if ((hw->features & HALF_DUPLEX_SIGNAL_BUG) &&
+ !(hw->overrides & PAUSE_FLOW_CTRL)) {
+ u32 cfg = hw->tx_cfg;
+
+ /* Disable flow control in the half duplex mode. */
+ if (1 == info->duplex)
+ hw->tx_cfg &= ~DMA_TX_FLOW_ENABLE;
+ if (hw->enabled && cfg != hw->tx_cfg)
+ writel(hw->tx_cfg, hw->io + KS_DMA_TX_CTRL);
+ }
+}
+
+/**
+ * port_get_link_speed - get current link status
+ * @port: The port instance.
+ *
+ * This routine reads PHY registers to determine the current link status of the
+ * switch ports.
+ */
+static void port_get_link_speed(struct ksz_port *port)
+{
+ uint interrupt;
+ struct ksz_port_info *info;
+ struct ksz_port_info *linked = NULL;
+ struct ksz_hw *hw = port->hw;
+ u16 data;
+ u16 status;
+ u8 local;
+ u8 remote;
+ int i;
+ int p;
+ int change = 0;
+
+ interrupt = hw_block_intr(hw);
+
+ for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
+ info = &hw->port_info[p];
+ port_r16(hw, p, KS884X_PORT_CTRL_4_OFFSET, &data);
+ port_r16(hw, p, KS884X_PORT_STATUS_OFFSET, &status);
+
+ /*
+ * Link status is changing all the time even when there is no
+ * cable connection!
+ */
+ remote = status & (PORT_AUTO_NEG_COMPLETE |
+ PORT_STATUS_LINK_GOOD);
+ local = (u8) data;
+
+ /* No change to status. */
+ if (local == info->advertised && remote == info->partner)
+ continue;
+
+ info->advertised = local;
+ info->partner = remote;
+ if (status & PORT_STATUS_LINK_GOOD) {
+
+ /* Remember the first linked port. */
+ if (!linked)
+ linked = info;
+
+ info->tx_rate = 10 * TX_RATE_UNIT;
+ if (status & PORT_STATUS_SPEED_100MBIT)
+ info->tx_rate = 100 * TX_RATE_UNIT;
+
+ info->duplex = 1;
+ if (status & PORT_STATUS_FULL_DUPLEX)
+ info->duplex = 2;
+
+ if (media_connected != info->state) {
+ hw_r_phy(hw, p, KS884X_PHY_AUTO_NEG_OFFSET,
+ &data);
+ hw_r_phy(hw, p, KS884X_PHY_REMOTE_CAP_OFFSET,
+ &status);
+ determine_flow_ctrl(hw, port, data, status);
+ if (hw->ksz_switch) {
+ port_cfg_back_pressure(hw, p,
+ (1 == info->duplex));
+ }
+ change |= 1 << i;
+ port_cfg_change(hw, port, info, status);
+ }
+ info->state = media_connected;
+ } else {
+ if (media_disconnected != info->state) {
+ change |= 1 << i;
+
+ /* Indicate the link just goes down. */
+ hw->port_mib[p].link_down = 1;
+ }
+ info->state = media_disconnected;
+ }
+ hw->port_mib[p].state = (u8) info->state;
+ }
+
+ if (linked && media_disconnected == port->linked->state)
+ port->linked = linked;
+
+ hw_restore_intr(hw, interrupt);
+}
+
+#define PHY_RESET_TIMEOUT 10
+
+/**
+ * port_set_link_speed - set port speed
+ * @port: The port instance.
+ *
+ * This routine sets the link speed of the switch ports.
+ */
+static void port_set_link_speed(struct ksz_port *port)
+{
+ struct ksz_port_info *info;
+ struct ksz_hw *hw = port->hw;
+ u16 data;
+ u16 cfg;
+ u8 status;
+ int i;
+ int p;
+
+ for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
+ info = &hw->port_info[p];
+
+ port_r16(hw, p, KS884X_PORT_CTRL_4_OFFSET, &data);
+ port_r8(hw, p, KS884X_PORT_STATUS_OFFSET, &status);
+
+ cfg = 0;
+ if (status & PORT_STATUS_LINK_GOOD)
+ cfg = data;
+
+ data |= PORT_AUTO_NEG_ENABLE;
+ data = advertised_flow_ctrl(port, data);
+
+ data |= PORT_AUTO_NEG_100BTX_FD | PORT_AUTO_NEG_100BTX |
+ PORT_AUTO_NEG_10BT_FD | PORT_AUTO_NEG_10BT;
+
+ /* Check if manual configuration is specified by the user. */
+ if (port->speed || port->duplex) {
+ if (10 == port->speed)
+ data &= ~(PORT_AUTO_NEG_100BTX_FD |
+ PORT_AUTO_NEG_100BTX);
+ else if (100 == port->speed)
+ data &= ~(PORT_AUTO_NEG_10BT_FD |
+ PORT_AUTO_NEG_10BT);
+ if (1 == port->duplex)
+ data &= ~(PORT_AUTO_NEG_100BTX_FD |
+ PORT_AUTO_NEG_10BT_FD);
+ else if (2 == port->duplex)
+ data &= ~(PORT_AUTO_NEG_100BTX |
+ PORT_AUTO_NEG_10BT);
+ }
+ if (data != cfg) {
+ data |= PORT_AUTO_NEG_RESTART;
+ port_w16(hw, p, KS884X_PORT_CTRL_4_OFFSET, data);
+ }
+ }
+}
+
+/**
+ * port_force_link_speed - force port speed
+ * @port: The port instance.
+ *
+ * This routine forces the link speed of the switch ports.
+ */
+static void port_force_link_speed(struct ksz_port *port)
+{
+ struct ksz_hw *hw = port->hw;
+ u16 data;
+ int i;
+ int phy;
+ int p;
+
+ for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
+ phy = KS884X_PHY_1_CTRL_OFFSET + p * PHY_CTRL_INTERVAL;
+ hw_r_phy_ctrl(hw, phy, &data);
+
+ data &= ~PHY_AUTO_NEG_ENABLE;
+
+ if (10 == port->speed)
+ data &= ~PHY_SPEED_100MBIT;
+ else if (100 == port->speed)
+ data |= PHY_SPEED_100MBIT;
+ if (1 == port->duplex)
+ data &= ~PHY_FULL_DUPLEX;
+ else if (2 == port->duplex)
+ data |= PHY_FULL_DUPLEX;
+ hw_w_phy_ctrl(hw, phy, data);
+ }
+}
+
+static void port_set_power_saving(struct ksz_port *port, int enable)
+{
+ struct ksz_hw *hw = port->hw;
+ int i;
+ int p;
+
+ for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++)
+ port_cfg(hw, p,
+ KS884X_PORT_CTRL_4_OFFSET, PORT_POWER_DOWN, enable);
+}
+
+/*
+ * KSZ8841 power management functions
+ */
+
+/**
+ * hw_chk_wol_pme_status - check PMEN pin
+ * @hw: The hardware instance.
+ *
+ * This function is used to check PMEN pin is asserted.
+ *
+ * Return 1 if PMEN pin is asserted; otherwise, 0.
+ */
+static int hw_chk_wol_pme_status(struct ksz_hw *hw)
+{
+ struct dev_info *hw_priv = container_of(hw, struct dev_info, hw);
+ struct pci_dev *pdev = hw_priv->pdev;
+ u16 data;
+
+ if (!pdev->pm_cap)
+ return 0;
+ pci_read_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, &data);
+ return (data & PCI_PM_CTRL_PME_STATUS) == PCI_PM_CTRL_PME_STATUS;
+}
+
+/**
+ * hw_clr_wol_pme_status - clear PMEN pin
+ * @hw: The hardware instance.
+ *
+ * This routine is used to clear PME_Status to deassert PMEN pin.
+ */
+static void hw_clr_wol_pme_status(struct ksz_hw *hw)
+{
+ struct dev_info *hw_priv = container_of(hw, struct dev_info, hw);
+ struct pci_dev *pdev = hw_priv->pdev;
+ u16 data;
+
+ if (!pdev->pm_cap)
+ return;
+
+ /* Clear PME_Status to deassert PMEN pin. */
+ pci_read_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, &data);
+ data |= PCI_PM_CTRL_PME_STATUS;
+ pci_write_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, data);
+}
+
+/**
+ * hw_cfg_wol_pme - enable or disable Wake-on-LAN
+ * @hw: The hardware instance.
+ * @set: The flag indicating whether to enable or disable.
+ *
+ * This routine is used to enable or disable Wake-on-LAN.
+ */
+static void hw_cfg_wol_pme(struct ksz_hw *hw, int set)
+{
+ struct dev_info *hw_priv = container_of(hw, struct dev_info, hw);
+ struct pci_dev *pdev = hw_priv->pdev;
+ u16 data;
+
+ if (!pdev->pm_cap)
+ return;
+ pci_read_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, &data);
+ data &= ~PCI_PM_CTRL_STATE_MASK;
+ if (set)
+ data |= PCI_PM_CTRL_PME_ENABLE | PCI_D3hot;
+ else
+ data &= ~PCI_PM_CTRL_PME_ENABLE;
+ pci_write_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, data);
+}
+
+/**
+ * hw_cfg_wol - configure Wake-on-LAN features
+ * @hw: The hardware instance.
+ * @frame: The pattern frame bit.
+ * @set: The flag indicating whether to enable or disable.
+ *
+ * This routine is used to enable or disable certain Wake-on-LAN features.
+ */
+static void hw_cfg_wol(struct ksz_hw *hw, u16 frame, int set)
+{
+ u16 data;
+
+ data = readw(hw->io + KS8841_WOL_CTRL_OFFSET);
+ if (set)
+ data |= frame;
+ else
+ data &= ~frame;
+ writew(data, hw->io + KS8841_WOL_CTRL_OFFSET);
+}
+
+/**
+ * hw_set_wol_frame - program Wake-on-LAN pattern
+ * @hw: The hardware instance.
+ * @i: The frame index.
+ * @mask_size: The size of the mask.
+ * @mask: Mask to ignore certain bytes in the pattern.
+ * @frame_size: The size of the frame.
+ * @pattern: The frame data.
+ *
+ * This routine is used to program Wake-on-LAN pattern.
+ */
+static void hw_set_wol_frame(struct ksz_hw *hw, int i, uint mask_size,
+ const u8 *mask, uint frame_size, const u8 *pattern)
+{
+ int bits;
+ int from;
+ int len;
+ int to;
+ u32 crc;
+ u8 data[64];
+ u8 val = 0;
+
+ if (frame_size > mask_size * 8)
+ frame_size = mask_size * 8;
+ if (frame_size > 64)
+ frame_size = 64;
+
+ i *= 0x10;
+ writel(0, hw->io + KS8841_WOL_FRAME_BYTE0_OFFSET + i);
+ writel(0, hw->io + KS8841_WOL_FRAME_BYTE2_OFFSET + i);
+
+ bits = len = from = to = 0;
+ do {
+ if (bits) {
+ if ((val & 1))
+ data[to++] = pattern[from];
+ val >>= 1;
+ ++from;
+ --bits;
+ } else {
+ val = mask[len];
+ writeb(val, hw->io + KS8841_WOL_FRAME_BYTE0_OFFSET + i
+ + len);
+ ++len;
+ if (val)
+ bits = 8;
+ else
+ from += 8;
+ }
+ } while (from < (int) frame_size);
+ if (val) {
+ bits = mask[len - 1];
+ val <<= (from % 8);
+ bits &= ~val;
+ writeb(bits, hw->io + KS8841_WOL_FRAME_BYTE0_OFFSET + i + len -
+ 1);
+ }
+ crc = ether_crc(to, data);
+ writel(crc, hw->io + KS8841_WOL_FRAME_CRC_OFFSET + i);
+}
+
+/**
+ * hw_add_wol_arp - add ARP pattern
+ * @hw: The hardware instance.
+ * @ip_addr: The IPv4 address assigned to the device.
+ *
+ * This routine is used to add ARP pattern for waking up the host.
+ */
+static void hw_add_wol_arp(struct ksz_hw *hw, const u8 *ip_addr)
+{
+ static const u8 mask[6] = { 0x3F, 0xF0, 0x3F, 0x00, 0xC0, 0x03 };
+ u8 pattern[42] = {
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x08, 0x06,
+ 0x00, 0x01, 0x08, 0x00, 0x06, 0x04, 0x00, 0x01,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00 };
+
+ memcpy(&pattern[38], ip_addr, 4);
+ hw_set_wol_frame(hw, 3, 6, mask, 42, pattern);
+}
+
+/**
+ * hw_add_wol_bcast - add broadcast pattern
+ * @hw: The hardware instance.
+ *
+ * This routine is used to add broadcast pattern for waking up the host.
+ */
+static void hw_add_wol_bcast(struct ksz_hw *hw)
+{
+ static const u8 mask[] = { 0x3F };
+ static const u8 pattern[] = { 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF };
+
+ hw_set_wol_frame(hw, 2, 1, mask, MAC_ADDR_LEN, pattern);
+}
+
+/**
+ * hw_add_wol_mcast - add multicast pattern
+ * @hw: The hardware instance.
+ *
+ * This routine is used to add multicast pattern for waking up the host.
+ *
+ * It is assumed the multicast packet is the ICMPv6 neighbor solicitation used
+ * by IPv6 ping command. Note that multicast packets are filtred through the
+ * multicast hash table, so not all multicast packets can wake up the host.
+ */
+static void hw_add_wol_mcast(struct ksz_hw *hw)
+{
+ static const u8 mask[] = { 0x3F };
+ u8 pattern[] = { 0x33, 0x33, 0xFF, 0x00, 0x00, 0x00 };
+
+ memcpy(&pattern[3], &hw->override_addr[3], 3);
+ hw_set_wol_frame(hw, 1, 1, mask, 6, pattern);
+}
+
+/**
+ * hw_add_wol_ucast - add unicast pattern
+ * @hw: The hardware instance.
+ *
+ * This routine is used to add unicast pattern to wakeup the host.
+ *
+ * It is assumed the unicast packet is directed to the device, as the hardware
+ * can only receive them in normal case.
+ */
+static void hw_add_wol_ucast(struct ksz_hw *hw)
+{
+ static const u8 mask[] = { 0x3F };
+
+ hw_set_wol_frame(hw, 0, 1, mask, MAC_ADDR_LEN, hw->override_addr);
+}
+
+/**
+ * hw_enable_wol - enable Wake-on-LAN
+ * @hw: The hardware instance.
+ * @wol_enable: The Wake-on-LAN settings.
+ * @net_addr: The IPv4 address assigned to the device.
+ *
+ * This routine is used to enable Wake-on-LAN depending on driver settings.
+ */
+static void hw_enable_wol(struct ksz_hw *hw, u32 wol_enable, const u8 *net_addr)
+{
+ hw_cfg_wol(hw, KS8841_WOL_MAGIC_ENABLE, (wol_enable & WAKE_MAGIC));
+ hw_cfg_wol(hw, KS8841_WOL_FRAME0_ENABLE, (wol_enable & WAKE_UCAST));
+ hw_add_wol_ucast(hw);
+ hw_cfg_wol(hw, KS8841_WOL_FRAME1_ENABLE, (wol_enable & WAKE_MCAST));
+ hw_add_wol_mcast(hw);
+ hw_cfg_wol(hw, KS8841_WOL_FRAME2_ENABLE, (wol_enable & WAKE_BCAST));
+ hw_cfg_wol(hw, KS8841_WOL_FRAME3_ENABLE, (wol_enable & WAKE_ARP));
+ hw_add_wol_arp(hw, net_addr);
+}
+
+/**
+ * hw_init - check driver is correct for the hardware
+ * @hw: The hardware instance.
+ *
+ * This function checks the hardware is correct for this driver and sets the
+ * hardware up for proper initialization.
+ *
+ * Return number of ports or 0 if not right.
+ */
+static int hw_init(struct ksz_hw *hw)
+{
+ int rc = 0;
+ u16 data;
+ u16 revision;
+
+ /* Set bus speed to 125MHz. */
+ writew(BUS_SPEED_125_MHZ, hw->io + KS884X_BUS_CTRL_OFFSET);
+
+ /* Check KSZ884x chip ID. */
+ data = readw(hw->io + KS884X_CHIP_ID_OFFSET);
+
+ revision = (data & KS884X_REVISION_MASK) >> KS884X_REVISION_SHIFT;
+ data &= KS884X_CHIP_ID_MASK_41;
+ if (REG_CHIP_ID_41 == data)
+ rc = 1;
+ else if (REG_CHIP_ID_42 == data)
+ rc = 2;
+ else
+ return 0;
+
+ /* Setup hardware features or bug workarounds. */
+ if (revision <= 1) {
+ hw->features |= SMALL_PACKET_TX_BUG;
+ if (1 == rc)
+ hw->features |= HALF_DUPLEX_SIGNAL_BUG;
+ }
+ return rc;
+}
+
+/**
+ * hw_reset - reset the hardware
+ * @hw: The hardware instance.
+ *
+ * This routine resets the hardware.
+ */
+static void hw_reset(struct ksz_hw *hw)
+{
+ writew(GLOBAL_SOFTWARE_RESET, hw->io + KS884X_GLOBAL_CTRL_OFFSET);
+
+ /* Wait for device to reset. */
+ mdelay(10);
+
+ /* Write 0 to clear device reset. */
+ writew(0, hw->io + KS884X_GLOBAL_CTRL_OFFSET);
+}
+
+/**
+ * hw_setup - setup the hardware
+ * @hw: The hardware instance.
+ *
+ * This routine setup the hardware for proper operation.
+ */
+static void hw_setup(struct ksz_hw *hw)
+{
+#if SET_DEFAULT_LED
+ u16 data;
+
+ /* Change default LED mode. */
+ data = readw(hw->io + KS8842_SWITCH_CTRL_5_OFFSET);
+ data &= ~LED_MODE;
+ data |= SET_DEFAULT_LED;
+ writew(data, hw->io + KS8842_SWITCH_CTRL_5_OFFSET);
+#endif
+
+ /* Setup transmit control. */
+ hw->tx_cfg = (DMA_TX_PAD_ENABLE | DMA_TX_CRC_ENABLE |
+ (DMA_BURST_DEFAULT << DMA_BURST_SHIFT) | DMA_TX_ENABLE);
+
+ /* Setup receive control. */
+ hw->rx_cfg = (DMA_RX_BROADCAST | DMA_RX_UNICAST |
+ (DMA_BURST_DEFAULT << DMA_BURST_SHIFT) | DMA_RX_ENABLE);
+ hw->rx_cfg |= KS884X_DMA_RX_MULTICAST;
+
+ /* Hardware cannot handle UDP packet in IP fragments. */
+ hw->rx_cfg |= (DMA_RX_CSUM_TCP | DMA_RX_CSUM_IP);
+
+ if (hw->all_multi)
+ hw->rx_cfg |= DMA_RX_ALL_MULTICAST;
+ if (hw->promiscuous)
+ hw->rx_cfg |= DMA_RX_PROMISCUOUS;
+}
+
+/**
+ * hw_setup_intr - setup interrupt mask
+ * @hw: The hardware instance.
+ *
+ * This routine setup the interrupt mask for proper operation.
+ */
+static void hw_setup_intr(struct ksz_hw *hw)
+{
+ hw->intr_mask = KS884X_INT_MASK | KS884X_INT_RX_OVERRUN;
+}
+
+static void ksz_check_desc_num(struct ksz_desc_info *info)
+{
+#define MIN_DESC_SHIFT 2
+
+ int alloc = info->alloc;
+ int shift;
+
+ shift = 0;
+ while (!(alloc & 1)) {
+ shift++;
+ alloc >>= 1;
+ }
+ if (alloc != 1 || shift < MIN_DESC_SHIFT) {
+ pr_alert("Hardware descriptor numbers not right!\n");
+ while (alloc) {
+ shift++;
+ alloc >>= 1;
+ }
+ if (shift < MIN_DESC_SHIFT)
+ shift = MIN_DESC_SHIFT;
+ alloc = 1 << shift;
+ info->alloc = alloc;
+ }
+ info->mask = info->alloc - 1;
+}
+
+static void hw_init_desc(struct ksz_desc_info *desc_info, int transmit)
+{
+ int i;
+ u32 phys = desc_info->ring_phys;
+ struct ksz_hw_desc *desc = desc_info->ring_virt;
+ struct ksz_desc *cur = desc_info->ring;
+ struct ksz_desc *previous = NULL;
+
+ for (i = 0; i < desc_info->alloc; i++) {
+ cur->phw = desc++;
+ phys += desc_info->size;
+ previous = cur++;
+ previous->phw->next = cpu_to_le32(phys);
+ }
+ previous->phw->next = cpu_to_le32(desc_info->ring_phys);
+ previous->sw.buf.rx.end_of_ring = 1;
+ previous->phw->buf.data = cpu_to_le32(previous->sw.buf.data);
+
+ desc_info->avail = desc_info->alloc;
+ desc_info->last = desc_info->next = 0;
+
+ desc_info->cur = desc_info->ring;
+}
+
+/**
+ * hw_set_desc_base - set descriptor base addresses
+ * @hw: The hardware instance.
+ * @tx_addr: The transmit descriptor base.
+ * @rx_addr: The receive descriptor base.
+ *
+ * This routine programs the descriptor base addresses after reset.
+ */
+static void hw_set_desc_base(struct ksz_hw *hw, u32 tx_addr, u32 rx_addr)
+{
+ /* Set base address of Tx/Rx descriptors. */
+ writel(tx_addr, hw->io + KS_DMA_TX_ADDR);
+ writel(rx_addr, hw->io + KS_DMA_RX_ADDR);
+}
+
+static void hw_reset_pkts(struct ksz_desc_info *info)
+{
+ info->cur = info->ring;
+ info->avail = info->alloc;
+ info->last = info->next = 0;
+}
+
+static inline void hw_resume_rx(struct ksz_hw *hw)
+{
+ writel(DMA_START, hw->io + KS_DMA_RX_START);
+}
+
+/**
+ * hw_start_rx - start receiving
+ * @hw: The hardware instance.
+ *
+ * This routine starts the receive function of the hardware.
+ */
+static void hw_start_rx(struct ksz_hw *hw)
+{
+ writel(hw->rx_cfg, hw->io + KS_DMA_RX_CTRL);
+
+ /* Notify when the receive stops. */
+ hw->intr_mask |= KS884X_INT_RX_STOPPED;
+
+ writel(DMA_START, hw->io + KS_DMA_RX_START);
+ hw_ack_intr(hw, KS884X_INT_RX_STOPPED);
+ hw->rx_stop++;
+
+ /* Variable overflows. */
+ if (0 == hw->rx_stop)
+ hw->rx_stop = 2;
+}
+
+/*
+ * hw_stop_rx - stop receiving
+ * @hw: The hardware instance.
+ *
+ * This routine stops the receive function of the hardware.
+ */
+static void hw_stop_rx(struct ksz_hw *hw)
+{
+ hw->rx_stop = 0;
+ hw_turn_off_intr(hw, KS884X_INT_RX_STOPPED);
+ writel((hw->rx_cfg & ~DMA_RX_ENABLE), hw->io + KS_DMA_RX_CTRL);
+}
+
+/**
+ * hw_start_tx - start transmitting
+ * @hw: The hardware instance.
+ *
+ * This routine starts the transmit function of the hardware.
+ */
+static void hw_start_tx(struct ksz_hw *hw)
+{
+ writel(hw->tx_cfg, hw->io + KS_DMA_TX_CTRL);
+}
+
+/**
+ * hw_stop_tx - stop transmitting
+ * @hw: The hardware instance.
+ *
+ * This routine stops the transmit function of the hardware.
+ */
+static void hw_stop_tx(struct ksz_hw *hw)
+{
+ writel((hw->tx_cfg & ~DMA_TX_ENABLE), hw->io + KS_DMA_TX_CTRL);
+}
+
+/**
+ * hw_disable - disable hardware
+ * @hw: The hardware instance.
+ *
+ * This routine disables the hardware.
+ */
+static void hw_disable(struct ksz_hw *hw)
+{
+ hw_stop_rx(hw);
+ hw_stop_tx(hw);
+ hw->enabled = 0;
+}
+
+/**
+ * hw_enable - enable hardware
+ * @hw: The hardware instance.
+ *
+ * This routine enables the hardware.
+ */
+static void hw_enable(struct ksz_hw *hw)
+{
+ hw_start_tx(hw);
+ hw_start_rx(hw);
+ hw->enabled = 1;
+}
+
+/**
+ * hw_alloc_pkt - allocate enough descriptors for transmission
+ * @hw: The hardware instance.
+ * @length: The length of the packet.
+ * @physical: Number of descriptors required.
+ *
+ * This function allocates descriptors for transmission.
+ *
+ * Return 0 if not successful; 1 for buffer copy; or number of descriptors.
+ */
+static int hw_alloc_pkt(struct ksz_hw *hw, int length, int physical)
+{
+ /* Always leave one descriptor free. */
+ if (hw->tx_desc_info.avail <= 1)
+ return 0;
+
+ /* Allocate a descriptor for transmission and mark it current. */
+ get_tx_pkt(&hw->tx_desc_info, &hw->tx_desc_info.cur);
+ hw->tx_desc_info.cur->sw.buf.tx.first_seg = 1;
+
+ /* Keep track of number of transmit descriptors used so far. */
+ ++hw->tx_int_cnt;
+ hw->tx_size += length;
+
+ /* Cannot hold on too much data. */
+ if (hw->tx_size >= MAX_TX_HELD_SIZE)
+ hw->tx_int_cnt = hw->tx_int_mask + 1;
+
+ if (physical > hw->tx_desc_info.avail)
+ return 1;
+
+ return hw->tx_desc_info.avail;
+}
+
+/**
+ * hw_send_pkt - mark packet for transmission
+ * @hw: The hardware instance.
+ *
+ * This routine marks the packet for transmission in PCI version.
+ */
+static void hw_send_pkt(struct ksz_hw *hw)
+{
+ struct ksz_desc *cur = hw->tx_desc_info.cur;
+
+ cur->sw.buf.tx.last_seg = 1;
+
+ /* Interrupt only after specified number of descriptors used. */
+ if (hw->tx_int_cnt > hw->tx_int_mask) {
+ cur->sw.buf.tx.intr = 1;
+ hw->tx_int_cnt = 0;
+ hw->tx_size = 0;
+ }
+
+ /* KSZ8842 supports port directed transmission. */
+ cur->sw.buf.tx.dest_port = hw->dst_ports;
+
+ release_desc(cur);
+
+ writel(0, hw->io + KS_DMA_TX_START);
+}
+
+static int empty_addr(u8 *addr)
+{
+ u32 *addr1 = (u32 *) addr;
+ u16 *addr2 = (u16 *) &addr[4];
+
+ return 0 == *addr1 && 0 == *addr2;
+}
+
+/**
+ * hw_set_addr - set MAC address
+ * @hw: The hardware instance.
+ *
+ * This routine programs the MAC address of the hardware when the address is
+ * overrided.
+ */
+static void hw_set_addr(struct ksz_hw *hw)
+{
+ int i;
+
+ for (i = 0; i < MAC_ADDR_LEN; i++)
+ writeb(hw->override_addr[MAC_ADDR_ORDER(i)],
+ hw->io + KS884X_ADDR_0_OFFSET + i);
+
+ sw_set_addr(hw, hw->override_addr);
+}
+
+/**
+ * hw_read_addr - read MAC address
+ * @hw: The hardware instance.
+ *
+ * This routine retrieves the MAC address of the hardware.
+ */
+static void hw_read_addr(struct ksz_hw *hw)
+{
+ int i;
+
+ for (i = 0; i < MAC_ADDR_LEN; i++)
+ hw->perm_addr[MAC_ADDR_ORDER(i)] = readb(hw->io +
+ KS884X_ADDR_0_OFFSET + i);
+
+ if (!hw->mac_override) {
+ memcpy(hw->override_addr, hw->perm_addr, MAC_ADDR_LEN);
+ if (empty_addr(hw->override_addr)) {
+ memcpy(hw->perm_addr, DEFAULT_MAC_ADDRESS,
+ MAC_ADDR_LEN);
+ memcpy(hw->override_addr, DEFAULT_MAC_ADDRESS,
+ MAC_ADDR_LEN);
+ hw->override_addr[5] += hw->id;
+ hw_set_addr(hw);
+ }
+ }
+}
+
+static void hw_ena_add_addr(struct ksz_hw *hw, int index, u8 *mac_addr)
+{
+ int i;
+ u32 mac_addr_lo;
+ u32 mac_addr_hi;
+
+ mac_addr_hi = 0;
+ for (i = 0; i < 2; i++) {
+ mac_addr_hi <<= 8;
+ mac_addr_hi |= mac_addr[i];
+ }
+ mac_addr_hi |= ADD_ADDR_ENABLE;
+ mac_addr_lo = 0;
+ for (i = 2; i < 6; i++) {
+ mac_addr_lo <<= 8;
+ mac_addr_lo |= mac_addr[i];
+ }
+ index *= ADD_ADDR_INCR;
+
+ writel(mac_addr_lo, hw->io + index + KS_ADD_ADDR_0_LO);
+ writel(mac_addr_hi, hw->io + index + KS_ADD_ADDR_0_HI);
+}
+
+static void hw_set_add_addr(struct ksz_hw *hw)
+{
+ int i;
+
+ for (i = 0; i < ADDITIONAL_ENTRIES; i++) {
+ if (empty_addr(hw->address[i]))
+ writel(0, hw->io + ADD_ADDR_INCR * i +
+ KS_ADD_ADDR_0_HI);
+ else
+ hw_ena_add_addr(hw, i, hw->address[i]);
+ }
+}
+
+static int hw_add_addr(struct ksz_hw *hw, u8 *mac_addr)
+{
+ int i;
+ int j = ADDITIONAL_ENTRIES;
+
+ if (!memcmp(hw->override_addr, mac_addr, MAC_ADDR_LEN))
+ return 0;
+ for (i = 0; i < hw->addr_list_size; i++) {
+ if (!memcmp(hw->address[i], mac_addr, MAC_ADDR_LEN))
+ return 0;
+ if (ADDITIONAL_ENTRIES == j && empty_addr(hw->address[i]))
+ j = i;
+ }
+ if (j < ADDITIONAL_ENTRIES) {
+ memcpy(hw->address[j], mac_addr, MAC_ADDR_LEN);
+ hw_ena_add_addr(hw, j, hw->address[j]);
+ return 0;
+ }
+ return -1;
+}
+
+static int hw_del_addr(struct ksz_hw *hw, u8 *mac_addr)
+{
+ int i;
+
+ for (i = 0; i < hw->addr_list_size; i++) {
+ if (!memcmp(hw->address[i], mac_addr, MAC_ADDR_LEN)) {
+ memset(hw->address[i], 0, MAC_ADDR_LEN);
+ writel(0, hw->io + ADD_ADDR_INCR * i +
+ KS_ADD_ADDR_0_HI);
+ return 0;
+ }
+ }
+ return -1;
+}
+
+/**
+ * hw_clr_multicast - clear multicast addresses
+ * @hw: The hardware instance.
+ *
+ * This routine removes all multicast addresses set in the hardware.
+ */
+static void hw_clr_multicast(struct ksz_hw *hw)
+{
+ int i;
+
+ for (i = 0; i < HW_MULTICAST_SIZE; i++) {
+ hw->multi_bits[i] = 0;
+
+ writeb(0, hw->io + KS884X_MULTICAST_0_OFFSET + i);
+ }
+}
+
+/**
+ * hw_set_grp_addr - set multicast addresses
+ * @hw: The hardware instance.
+ *
+ * This routine programs multicast addresses for the hardware to accept those
+ * addresses.
+ */
+static void hw_set_grp_addr(struct ksz_hw *hw)
+{
+ int i;
+ int index;
+ int position;
+ int value;
+
+ memset(hw->multi_bits, 0, sizeof(u8) * HW_MULTICAST_SIZE);
+
+ for (i = 0; i < hw->multi_list_size; i++) {
+ position = (ether_crc(6, hw->multi_list[i]) >> 26) & 0x3f;
+ index = position >> 3;
+ value = 1 << (position & 7);
+ hw->multi_bits[index] |= (u8) value;
+ }
+
+ for (i = 0; i < HW_MULTICAST_SIZE; i++)
+ writeb(hw->multi_bits[i], hw->io + KS884X_MULTICAST_0_OFFSET +
+ i);
+}
+
+/**
+ * hw_set_multicast - enable or disable all multicast receiving
+ * @hw: The hardware instance.
+ * @multicast: To turn on or off the all multicast feature.
+ *
+ * This routine enables/disables the hardware to accept all multicast packets.
+ */
+static void hw_set_multicast(struct ksz_hw *hw, u8 multicast)
+{
+ /* Stop receiving for reconfiguration. */
+ hw_stop_rx(hw);
+
+ if (multicast)
+ hw->rx_cfg |= DMA_RX_ALL_MULTICAST;
+ else
+ hw->rx_cfg &= ~DMA_RX_ALL_MULTICAST;
+
+ if (hw->enabled)
+ hw_start_rx(hw);
+}
+
+/**
+ * hw_set_promiscuous - enable or disable promiscuous receiving
+ * @hw: The hardware instance.
+ * @prom: To turn on or off the promiscuous feature.
+ *
+ * This routine enables/disables the hardware to accept all packets.
+ */
+static void hw_set_promiscuous(struct ksz_hw *hw, u8 prom)
+{
+ /* Stop receiving for reconfiguration. */
+ hw_stop_rx(hw);
+
+ if (prom)
+ hw->rx_cfg |= DMA_RX_PROMISCUOUS;
+ else
+ hw->rx_cfg &= ~DMA_RX_PROMISCUOUS;
+
+ if (hw->enabled)
+ hw_start_rx(hw);
+}
+
+/**
+ * sw_enable - enable the switch
+ * @hw: The hardware instance.
+ * @enable: The flag to enable or disable the switch
+ *
+ * This routine is used to enable/disable the switch in KSZ8842.
+ */
+static void sw_enable(struct ksz_hw *hw, int enable)
+{
+ int port;
+
+ for (port = 0; port < SWITCH_PORT_NUM; port++) {
+ if (hw->dev_count > 1) {
+ /* Set port-base vlan membership with host port. */
+ sw_cfg_port_base_vlan(hw, port,
+ HOST_MASK | (1 << port));
+ port_set_stp_state(hw, port, STP_STATE_DISABLED);
+ } else {
+ sw_cfg_port_base_vlan(hw, port, PORT_MASK);
+ port_set_stp_state(hw, port, STP_STATE_FORWARDING);
+ }
+ }
+ if (hw->dev_count > 1)
+ port_set_stp_state(hw, SWITCH_PORT_NUM, STP_STATE_SIMPLE);
+ else
+ port_set_stp_state(hw, SWITCH_PORT_NUM, STP_STATE_FORWARDING);
+
+ if (enable)
+ enable = KS8842_START;
+ writew(enable, hw->io + KS884X_CHIP_ID_OFFSET);
+}
+
+/**
+ * sw_setup - setup the switch
+ * @hw: The hardware instance.
+ *
+ * This routine setup the hardware switch engine for default operation.
+ */
+static void sw_setup(struct ksz_hw *hw)
+{
+ int port;
+
+ sw_set_global_ctrl(hw);
+
+ /* Enable switch broadcast storm protection at 10% percent rate. */
+ sw_init_broad_storm(hw);
+ hw_cfg_broad_storm(hw, BROADCAST_STORM_PROTECTION_RATE);
+ for (port = 0; port < SWITCH_PORT_NUM; port++)
+ sw_ena_broad_storm(hw, port);
+
+ sw_init_prio(hw);
+
+ sw_init_mirror(hw);
+
+ sw_init_prio_rate(hw);
+
+ sw_init_vlan(hw);
+
+ if (hw->features & STP_SUPPORT)
+ sw_init_stp(hw);
+ if (!sw_chk(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_TX_FLOW_CTRL | SWITCH_RX_FLOW_CTRL))
+ hw->overrides |= PAUSE_FLOW_CTRL;
+ sw_enable(hw, 1);
+}
+
+/**
+ * ksz_start_timer - start kernel timer
+ * @info: Kernel timer information.
+ * @time: The time tick.
+ *
+ * This routine starts the kernel timer after the specified time tick.
+ */
+static void ksz_start_timer(struct ksz_timer_info *info, int time)
+{
+ info->cnt = 0;
+ info->timer.expires = jiffies + time;
+ add_timer(&info->timer);
+
+ /* infinity */
+ info->max = -1;
+}
+
+/**
+ * ksz_stop_timer - stop kernel timer
+ * @info: Kernel timer information.
+ *
+ * This routine stops the kernel timer.
+ */
+static void ksz_stop_timer(struct ksz_timer_info *info)
+{
+ if (info->max) {
+ info->max = 0;
+ del_timer_sync(&info->timer);
+ }
+}
+
+static void ksz_init_timer(struct ksz_timer_info *info, int period,
+ void (*function)(unsigned long), void *data)
+{
+ info->max = 0;
+ info->period = period;
+ init_timer(&info->timer);
+ info->timer.function = function;
+ info->timer.data = (unsigned long) data;
+}
+
+static void ksz_update_timer(struct ksz_timer_info *info)
+{
+ ++info->cnt;
+ if (info->max > 0) {
+ if (info->cnt < info->max) {
+ info->timer.expires = jiffies + info->period;
+ add_timer(&info->timer);
+ } else
+ info->max = 0;
+ } else if (info->max < 0) {
+ info->timer.expires = jiffies + info->period;
+ add_timer(&info->timer);
+ }
+}
+
+/**
+ * ksz_alloc_soft_desc - allocate software descriptors
+ * @desc_info: Descriptor information structure.
+ * @transmit: Indication that descriptors are for transmit.
+ *
+ * This local function allocates software descriptors for manipulation in
+ * memory.
+ *
+ * Return 0 if successful.
+ */
+static int ksz_alloc_soft_desc(struct ksz_desc_info *desc_info, int transmit)
+{
+ desc_info->ring = kmalloc(sizeof(struct ksz_desc) * desc_info->alloc,
+ GFP_KERNEL);
+ if (!desc_info->ring)
+ return 1;
+ memset((void *) desc_info->ring, 0,
+ sizeof(struct ksz_desc) * desc_info->alloc);
+ hw_init_desc(desc_info, transmit);
+ return 0;
+}
+
+/**
+ * ksz_alloc_desc - allocate hardware descriptors
+ * @adapter: Adapter information structure.
+ *
+ * This local function allocates hardware descriptors for receiving and
+ * transmitting.
+ *
+ * Return 0 if successful.
+ */
+static int ksz_alloc_desc(struct dev_info *adapter)
+{
+ struct ksz_hw *hw = &adapter->hw;
+ int offset;
+
+ /* Allocate memory for RX & TX descriptors. */
+ adapter->desc_pool.alloc_size =
+ hw->rx_desc_info.size * hw->rx_desc_info.alloc +
+ hw->tx_desc_info.size * hw->tx_desc_info.alloc +
+ DESC_ALIGNMENT;
+
+ adapter->desc_pool.alloc_virt =
+ pci_alloc_consistent(
+ adapter->pdev, adapter->desc_pool.alloc_size,
+ &adapter->desc_pool.dma_addr);
+ if (adapter->desc_pool.alloc_virt == NULL) {
+ adapter->desc_pool.alloc_size = 0;
+ return 1;
+ }
+ memset(adapter->desc_pool.alloc_virt, 0, adapter->desc_pool.alloc_size);
+
+ /* Align to the next cache line boundary. */
+ offset = (((ulong) adapter->desc_pool.alloc_virt % DESC_ALIGNMENT) ?
+ (DESC_ALIGNMENT -
+ ((ulong) adapter->desc_pool.alloc_virt % DESC_ALIGNMENT)) : 0);
+ adapter->desc_pool.virt = adapter->desc_pool.alloc_virt + offset;
+ adapter->desc_pool.phys = adapter->desc_pool.dma_addr + offset;
+
+ /* Allocate receive/transmit descriptors. */
+ hw->rx_desc_info.ring_virt = (struct ksz_hw_desc *)
+ adapter->desc_pool.virt;
+ hw->rx_desc_info.ring_phys = adapter->desc_pool.phys;
+ offset = hw->rx_desc_info.alloc * hw->rx_desc_info.size;
+ hw->tx_desc_info.ring_virt = (struct ksz_hw_desc *)
+ (adapter->desc_pool.virt + offset);
+ hw->tx_desc_info.ring_phys = adapter->desc_pool.phys + offset;
+
+ if (ksz_alloc_soft_desc(&hw->rx_desc_info, 0))
+ return 1;
+ if (ksz_alloc_soft_desc(&hw->tx_desc_info, 1))
+ return 1;
+
+ return 0;
+}
+
+/**
+ * free_dma_buf - release DMA buffer resources
+ * @adapter: Adapter information structure.
+ *
+ * This routine is just a helper function to release the DMA buffer resources.
+ */
+static void free_dma_buf(struct dev_info *adapter, struct ksz_dma_buf *dma_buf,
+ int direction)
+{
+ pci_unmap_single(adapter->pdev, dma_buf->dma, dma_buf->len, direction);
+ dev_kfree_skb(dma_buf->skb);
+ dma_buf->skb = NULL;
+ dma_buf->dma = 0;
+}
+
+/**
+ * ksz_init_rx_buffers - initialize receive descriptors
+ * @adapter: Adapter information structure.
+ *
+ * This routine initializes DMA buffers for receiving.
+ */
+static void ksz_init_rx_buffers(struct dev_info *adapter)
+{
+ int i;
+ struct ksz_desc *desc;
+ struct ksz_dma_buf *dma_buf;
+ struct ksz_hw *hw = &adapter->hw;
+ struct ksz_desc_info *info = &hw->rx_desc_info;
+
+ for (i = 0; i < hw->rx_desc_info.alloc; i++) {
+ get_rx_pkt(info, &desc);
+
+ dma_buf = DMA_BUFFER(desc);
+ if (dma_buf->skb && dma_buf->len != adapter->mtu)
+ free_dma_buf(adapter, dma_buf, PCI_DMA_FROMDEVICE);
+ dma_buf->len = adapter->mtu;
+ if (!dma_buf->skb)
+ dma_buf->skb = alloc_skb(dma_buf->len, GFP_ATOMIC);
+ if (dma_buf->skb && !dma_buf->dma) {
+ dma_buf->skb->dev = adapter->dev;
+ dma_buf->dma = pci_map_single(
+ adapter->pdev,
+ skb_tail_pointer(dma_buf->skb),
+ dma_buf->len,
+ PCI_DMA_FROMDEVICE);
+ }
+
+ /* Set descriptor. */
+ set_rx_buf(desc, dma_buf->dma);
+ set_rx_len(desc, dma_buf->len);
+ release_desc(desc);
+ }
+}
+
+/**
+ * ksz_alloc_mem - allocate memory for hardware descriptors
+ * @adapter: Adapter information structure.
+ *
+ * This function allocates memory for use by hardware descriptors for receiving
+ * and transmitting.
+ *
+ * Return 0 if successful.
+ */
+static int ksz_alloc_mem(struct dev_info *adapter)
+{
+ struct ksz_hw *hw = &adapter->hw;
+
+ /* Determine the number of receive and transmit descriptors. */
+ hw->rx_desc_info.alloc = NUM_OF_RX_DESC;
+ hw->tx_desc_info.alloc = NUM_OF_TX_DESC;
+
+ /* Determine how many descriptors to skip transmit interrupt. */
+ hw->tx_int_cnt = 0;
+ hw->tx_int_mask = NUM_OF_TX_DESC / 4;
+ if (hw->tx_int_mask > 8)
+ hw->tx_int_mask = 8;
+ while (hw->tx_int_mask) {
+ hw->tx_int_cnt++;
+ hw->tx_int_mask >>= 1;
+ }
+ if (hw->tx_int_cnt) {
+ hw->tx_int_mask = (1 << (hw->tx_int_cnt - 1)) - 1;
+ hw->tx_int_cnt = 0;
+ }
+
+ /* Determine the descriptor size. */
+ hw->rx_desc_info.size =
+ (((sizeof(struct ksz_hw_desc) + DESC_ALIGNMENT - 1) /
+ DESC_ALIGNMENT) * DESC_ALIGNMENT);
+ hw->tx_desc_info.size =
+ (((sizeof(struct ksz_hw_desc) + DESC_ALIGNMENT - 1) /
+ DESC_ALIGNMENT) * DESC_ALIGNMENT);
+ if (hw->rx_desc_info.size != sizeof(struct ksz_hw_desc))
+ pr_alert("Hardware descriptor size not right!\n");
+ ksz_check_desc_num(&hw->rx_desc_info);
+ ksz_check_desc_num(&hw->tx_desc_info);
+
+ /* Allocate descriptors. */
+ if (ksz_alloc_desc(adapter))
+ return 1;
+
+ return 0;
+}
+
+/**
+ * ksz_free_desc - free software and hardware descriptors
+ * @adapter: Adapter information structure.
+ *
+ * This local routine frees the software and hardware descriptors allocated by
+ * ksz_alloc_desc().
+ */
+static void ksz_free_desc(struct dev_info *adapter)
+{
+ struct ksz_hw *hw = &adapter->hw;
+
+ /* Reset descriptor. */
+ hw->rx_desc_info.ring_virt = NULL;
+ hw->tx_desc_info.ring_virt = NULL;
+ hw->rx_desc_info.ring_phys = 0;
+ hw->tx_desc_info.ring_phys = 0;
+
+ /* Free memory. */
+ if (adapter->desc_pool.alloc_virt)
+ pci_free_consistent(
+ adapter->pdev,
+ adapter->desc_pool.alloc_size,
+ adapter->desc_pool.alloc_virt,
+ adapter->desc_pool.dma_addr);
+
+ /* Reset resource pool. */
+ adapter->desc_pool.alloc_size = 0;
+ adapter->desc_pool.alloc_virt = NULL;
+
+ kfree(hw->rx_desc_info.ring);
+ hw->rx_desc_info.ring = NULL;
+ kfree(hw->tx_desc_info.ring);
+ hw->tx_desc_info.ring = NULL;
+}
+
+/**
+ * ksz_free_buffers - free buffers used in the descriptors
+ * @adapter: Adapter information structure.
+ * @desc_info: Descriptor information structure.
+ *
+ * This local routine frees buffers used in the DMA buffers.
+ */
+static void ksz_free_buffers(struct dev_info *adapter,
+ struct ksz_desc_info *desc_info, int direction)
+{
+ int i;
+ struct ksz_dma_buf *dma_buf;
+ struct ksz_desc *desc = desc_info->ring;
+
+ for (i = 0; i < desc_info->alloc; i++) {
+ dma_buf = DMA_BUFFER(desc);
+ if (dma_buf->skb)
+ free_dma_buf(adapter, dma_buf, direction);
+ desc++;
+ }
+}
+
+/**
+ * ksz_free_mem - free all resources used by descriptors
+ * @adapter: Adapter information structure.
+ *
+ * This local routine frees all the resources allocated by ksz_alloc_mem().
+ */
+static void ksz_free_mem(struct dev_info *adapter)
+{
+ /* Free transmit buffers. */
+ ksz_free_buffers(adapter, &adapter->hw.tx_desc_info,
+ PCI_DMA_TODEVICE);
+
+ /* Free receive buffers. */
+ ksz_free_buffers(adapter, &adapter->hw.rx_desc_info,
+ PCI_DMA_FROMDEVICE);
+
+ /* Free descriptors. */
+ ksz_free_desc(adapter);
+}
+
+static void get_mib_counters(struct ksz_hw *hw, int first, int cnt,
+ u64 *counter)
+{
+ int i;
+ int mib;
+ int port;
+ struct ksz_port_mib *port_mib;
+
+ memset(counter, 0, sizeof(u64) * TOTAL_PORT_COUNTER_NUM);
+ for (i = 0, port = first; i < cnt; i++, port++) {
+ port_mib = &hw->port_mib[port];
+ for (mib = port_mib->mib_start; mib < hw->mib_cnt; mib++)
+ counter[mib] += port_mib->counter[mib];
+ }
+}
+
+/**
+ * send_packet - send packet
+ * @skb: Socket buffer.
+ * @dev: Network device.
+ *
+ * This routine is used to send a packet out to the network.
+ */
+static void send_packet(struct sk_buff *skb, struct net_device *dev)
+{
+ struct ksz_desc *desc;
+ struct ksz_desc *first;
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_desc_info *info = &hw->tx_desc_info;
+ struct ksz_dma_buf *dma_buf;
+ int len;
+ int last_frag = skb_shinfo(skb)->nr_frags;
+
+ /*
+ * KSZ8842 with multiple device interfaces needs to be told which port
+ * to send.
+ */
+ if (hw->dev_count > 1)
+ hw->dst_ports = 1 << priv->port.first_port;
+
+ /* Hardware will pad the length to 60. */
+ len = skb->len;
+
+ /* Remember the very first descriptor. */
+ first = info->cur;
+ desc = first;
+
+ dma_buf = DMA_BUFFER(desc);
+ if (last_frag) {
+ int frag;
+ skb_frag_t *this_frag;
+
+ dma_buf->len = skb_headlen(skb);
+
+ dma_buf->dma = pci_map_single(
+ hw_priv->pdev, skb->data, dma_buf->len,
+ PCI_DMA_TODEVICE);
+ set_tx_buf(desc, dma_buf->dma);
+ set_tx_len(desc, dma_buf->len);
+
+ frag = 0;
+ do {
+ this_frag = &skb_shinfo(skb)->frags[frag];
+
+ /* Get a new descriptor. */
+ get_tx_pkt(info, &desc);
+
+ /* Keep track of descriptors used so far. */
+ ++hw->tx_int_cnt;
+
+ dma_buf = DMA_BUFFER(desc);
+ dma_buf->len = this_frag->size;
+
+ dma_buf->dma = pci_map_single(
+ hw_priv->pdev,
+ page_address(this_frag->page) +
+ this_frag->page_offset,
+ dma_buf->len,
+ PCI_DMA_TODEVICE);
+ set_tx_buf(desc, dma_buf->dma);
+ set_tx_len(desc, dma_buf->len);
+
+ frag++;
+ if (frag == last_frag)
+ break;
+
+ /* Do not release the last descriptor here. */
+ release_desc(desc);
+ } while (1);
+
+ /* current points to the last descriptor. */
+ info->cur = desc;
+
+ /* Release the first descriptor. */
+ release_desc(first);
+ } else {
+ dma_buf->len = len;
+
+ dma_buf->dma = pci_map_single(
+ hw_priv->pdev, skb->data, dma_buf->len,
+ PCI_DMA_TODEVICE);
+ set_tx_buf(desc, dma_buf->dma);
+ set_tx_len(desc, dma_buf->len);
+ }
+
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ (desc)->sw.buf.tx.csum_gen_tcp = 1;
+ (desc)->sw.buf.tx.csum_gen_udp = 1;
+ }
+
+ /*
+ * The last descriptor holds the packet so that it can be returned to
+ * network subsystem after all descriptors are transmitted.
+ */
+ dma_buf->skb = skb;
+
+ hw_send_pkt(hw);
+
+ /* Update transmit statistics. */
+ dev->stats.tx_packets++;
+ dev->stats.tx_bytes += len;
+}
+
+/**
+ * transmit_cleanup - clean up transmit descriptors
+ * @dev: Network device.
+ *
+ * This routine is called to clean up the transmitted buffers.
+ */
+static void transmit_cleanup(struct dev_info *hw_priv, int normal)
+{
+ int last;
+ union desc_stat status;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_desc_info *info = &hw->tx_desc_info;
+ struct ksz_desc *desc;
+ struct ksz_dma_buf *dma_buf;
+ struct net_device *dev = NULL;
+
+ spin_lock(&hw_priv->hwlock);
+ last = info->last;
+
+ while (info->avail < info->alloc) {
+ /* Get next descriptor which is not hardware owned. */
+ desc = &info->ring[last];
+ status.data = le32_to_cpu(desc->phw->ctrl.data);
+ if (status.tx.hw_owned) {
+ if (normal)
+ break;
+ else
+ reset_desc(desc, status);
+ }
+
+ dma_buf = DMA_BUFFER(desc);
+ pci_unmap_single(
+ hw_priv->pdev, dma_buf->dma, dma_buf->len,
+ PCI_DMA_TODEVICE);
+
+ /* This descriptor contains the last buffer in the packet. */
+ if (dma_buf->skb) {
+ dev = dma_buf->skb->dev;
+
+ /* Release the packet back to network subsystem. */
+ dev_kfree_skb_irq(dma_buf->skb);
+ dma_buf->skb = NULL;
+ }
+
+ /* Free the transmitted descriptor. */
+ last++;
+ last &= info->mask;
+ info->avail++;
+ }
+ info->last = last;
+ spin_unlock(&hw_priv->hwlock);
+
+ /* Notify the network subsystem that the packet has been sent. */
+ if (dev)
+ dev->trans_start = jiffies;
+}
+
+/**
+ * transmit_done - transmit done processing
+ * @dev: Network device.
+ *
+ * This routine is called when the transmit interrupt is triggered, indicating
+ * either a packet is sent successfully or there are transmit errors.
+ */
+static void tx_done(struct dev_info *hw_priv)
+{
+ struct ksz_hw *hw = &hw_priv->hw;
+ int port;
+
+ transmit_cleanup(hw_priv, 1);
+
+ for (port = 0; port < hw->dev_count; port++) {
+ struct net_device *dev = hw->port_info[port].pdev;
+
+ if (netif_running(dev) && netif_queue_stopped(dev))
+ netif_wake_queue(dev);
+ }
+}
+
+static inline void copy_old_skb(struct sk_buff *old, struct sk_buff *skb)
+{
+ skb->dev = old->dev;
+ skb->protocol = old->protocol;
+ skb->ip_summed = old->ip_summed;
+ skb->csum = old->csum;
+ skb_set_network_header(skb, ETH_HLEN);
+
+ dev_kfree_skb(old);
+}
+
+/**
+ * netdev_tx - send out packet
+ * @skb: Socket buffer.
+ * @dev: Network device.
+ *
+ * This function is used by the upper network layer to send out a packet.
+ *
+ * Return 0 if successful; otherwise an error code indicating failure.
+ */
+static netdev_tx_t netdev_tx(struct sk_buff *skb, struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ int left;
+ int num = 1;
+ int rc = 0;
+
+ if (hw->features & SMALL_PACKET_TX_BUG) {
+ struct sk_buff *org_skb = skb;
+
+ if (skb->len <= 48) {
+ if (skb_end_pointer(skb) - skb->data >= 50) {
+ memset(&skb->data[skb->len], 0, 50 - skb->len);
+ skb->len = 50;
+ } else {
+ skb = dev_alloc_skb(50);
+ if (!skb)
+ return NETDEV_TX_BUSY;
+ memcpy(skb->data, org_skb->data, org_skb->len);
+ memset(&skb->data[org_skb->len], 0,
+ 50 - org_skb->len);
+ skb->len = 50;
+ copy_old_skb(org_skb, skb);
+ }
+ }
+ }
+
+ spin_lock_irq(&hw_priv->hwlock);
+
+ num = skb_shinfo(skb)->nr_frags + 1;
+ left = hw_alloc_pkt(hw, skb->len, num);
+ if (left) {
+ if (left < num ||
+ ((CHECKSUM_PARTIAL == skb->ip_summed) &&
+ (ETH_P_IPV6 == htons(skb->protocol)))) {
+ struct sk_buff *org_skb = skb;
+
+ skb = dev_alloc_skb(org_skb->len);
+ if (!skb) {
+ rc = NETDEV_TX_BUSY;
+ goto unlock;
+ }
+ skb_copy_and_csum_dev(org_skb, skb->data);
+ org_skb->ip_summed = CHECKSUM_NONE;
+ skb->len = org_skb->len;
+ copy_old_skb(org_skb, skb);
+ }
+ send_packet(skb, dev);
+ if (left <= num)
+ netif_stop_queue(dev);
+ } else {
+ /* Stop the transmit queue until packet is allocated. */
+ netif_stop_queue(dev);
+ rc = NETDEV_TX_BUSY;
+ }
+unlock:
+ spin_unlock_irq(&hw_priv->hwlock);
+
+ return rc;
+}
+
+/**
+ * netdev_tx_timeout - transmit timeout processing
+ * @dev: Network device.
+ *
+ * This routine is called when the transmit timer expires. That indicates the
+ * hardware is not running correctly because transmit interrupts are not
+ * triggered to free up resources so that the transmit routine can continue
+ * sending out packets. The hardware is reset to correct the problem.
+ */
+static void netdev_tx_timeout(struct net_device *dev)
+{
+ static unsigned long last_reset;
+
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ int port;
+
+ if (hw->dev_count > 1) {
+ /*
+ * Only reset the hardware if time between calls is long
+ * enough.
+ */
+ if (jiffies - last_reset <= dev->watchdog_timeo)
+ hw_priv = NULL;
+ }
+
+ last_reset = jiffies;
+ if (hw_priv) {
+ hw_dis_intr(hw);
+ hw_disable(hw);
+
+ transmit_cleanup(hw_priv, 0);
+ hw_reset_pkts(&hw->rx_desc_info);
+ hw_reset_pkts(&hw->tx_desc_info);
+ ksz_init_rx_buffers(hw_priv);
+
+ hw_reset(hw);
+
+ hw_set_desc_base(hw,
+ hw->tx_desc_info.ring_phys,
+ hw->rx_desc_info.ring_phys);
+ hw_set_addr(hw);
+ if (hw->all_multi)
+ hw_set_multicast(hw, hw->all_multi);
+ else if (hw->multi_list_size)
+ hw_set_grp_addr(hw);
+
+ if (hw->dev_count > 1) {
+ hw_set_add_addr(hw);
+ for (port = 0; port < SWITCH_PORT_NUM; port++) {
+ struct net_device *port_dev;
+
+ port_set_stp_state(hw, port,
+ STP_STATE_DISABLED);
+
+ port_dev = hw->port_info[port].pdev;
+ if (netif_running(port_dev))
+ port_set_stp_state(hw, port,
+ STP_STATE_SIMPLE);
+ }
+ }
+
+ hw_enable(hw);
+ hw_ena_intr(hw);
+ }
+
+ dev->trans_start = jiffies;
+ netif_wake_queue(dev);
+}
+
+static inline void csum_verified(struct sk_buff *skb)
+{
+ unsigned short protocol;
+ struct iphdr *iph;
+
+ protocol = skb->protocol;
+ skb_reset_network_header(skb);
+ iph = (struct iphdr *) skb_network_header(skb);
+ if (protocol == htons(ETH_P_8021Q)) {
+ protocol = iph->tot_len;
+ skb_set_network_header(skb, VLAN_HLEN);
+ iph = (struct iphdr *) skb_network_header(skb);
+ }
+ if (protocol == htons(ETH_P_IP)) {
+ if (iph->protocol == IPPROTO_TCP)
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ }
+}
+
+static inline int rx_proc(struct net_device *dev, struct ksz_hw* hw,
+ struct ksz_desc *desc, union desc_stat status)
+{
+ int packet_len;
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_dma_buf *dma_buf;
+ struct sk_buff *skb;
+ int rx_status;
+
+ /* Received length includes 4-byte CRC. */
+ packet_len = status.rx.frame_len - 4;
+
+ dma_buf = DMA_BUFFER(desc);
+ pci_dma_sync_single_for_cpu(
+ hw_priv->pdev, dma_buf->dma, packet_len + 4,
+ PCI_DMA_FROMDEVICE);
+
+ do {
+ /* skb->data != skb->head */
+ skb = dev_alloc_skb(packet_len + 2);
+ if (!skb) {
+ dev->stats.rx_dropped++;
+ return -ENOMEM;
+ }
+
+ /*
+ * Align socket buffer in 4-byte boundary for better
+ * performance.
+ */
+ skb_reserve(skb, 2);
+
+ memcpy(skb_put(skb, packet_len),
+ dma_buf->skb->data, packet_len);
+ } while (0);
+
+ skb->protocol = eth_type_trans(skb, dev);
+
+ if (hw->rx_cfg & (DMA_RX_CSUM_UDP | DMA_RX_CSUM_TCP))
+ csum_verified(skb);
+
+ /* Update receive statistics. */
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += packet_len;
+
+ /* Notify upper layer for received packet. */
+ rx_status = netif_rx(skb);
+
+ return 0;
+}
+
+static int dev_rcv_packets(struct dev_info *hw_priv)
+{
+ int next;
+ union desc_stat status;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct net_device *dev = hw->port_info[0].pdev;
+ struct ksz_desc_info *info = &hw->rx_desc_info;
+ int left = info->alloc;
+ struct ksz_desc *desc;
+ int received = 0;
+
+ next = info->next;
+ while (left--) {
+ /* Get next descriptor which is not hardware owned. */
+ desc = &info->ring[next];
+ status.data = le32_to_cpu(desc->phw->ctrl.data);
+ if (status.rx.hw_owned)
+ break;
+
+ /* Status valid only when last descriptor bit is set. */
+ if (status.rx.last_desc && status.rx.first_desc) {
+ if (rx_proc(dev, hw, desc, status))
+ goto release_packet;
+ received++;
+ }
+
+release_packet:
+ release_desc(desc);
+ next++;
+ next &= info->mask;
+ }
+ info->next = next;
+
+ return received;
+}
+
+static int port_rcv_packets(struct dev_info *hw_priv)
+{
+ int next;
+ union desc_stat status;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct net_device *dev = hw->port_info[0].pdev;
+ struct ksz_desc_info *info = &hw->rx_desc_info;
+ int left = info->alloc;
+ struct ksz_desc *desc;
+ int received = 0;
+
+ next = info->next;
+ while (left--) {
+ /* Get next descriptor which is not hardware owned. */
+ desc = &info->ring[next];
+ status.data = le32_to_cpu(desc->phw->ctrl.data);
+ if (status.rx.hw_owned)
+ break;
+
+ if (hw->dev_count > 1) {
+ /* Get received port number. */
+ int p = HW_TO_DEV_PORT(status.rx.src_port);
+
+ dev = hw->port_info[p].pdev;
+ if (!netif_running(dev))
+ goto release_packet;
+ }
+
+ /* Status valid only when last descriptor bit is set. */
+ if (status.rx.last_desc && status.rx.first_desc) {
+ if (rx_proc(dev, hw, desc, status))
+ goto release_packet;
+ received++;
+ }
+
+release_packet:
+ release_desc(desc);
+ next++;
+ next &= info->mask;
+ }
+ info->next = next;
+
+ return received;
+}
+
+static int dev_rcv_special(struct dev_info *hw_priv)
+{
+ int next;
+ union desc_stat status;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct net_device *dev = hw->port_info[0].pdev;
+ struct ksz_desc_info *info = &hw->rx_desc_info;
+ int left = info->alloc;
+ struct ksz_desc *desc;
+ int received = 0;
+
+ next = info->next;
+ while (left--) {
+ /* Get next descriptor which is not hardware owned. */
+ desc = &info->ring[next];
+ status.data = le32_to_cpu(desc->phw->ctrl.data);
+ if (status.rx.hw_owned)
+ break;
+
+ if (hw->dev_count > 1) {
+ /* Get received port number. */
+ int p = HW_TO_DEV_PORT(status.rx.src_port);
+
+ dev = hw->port_info[p].pdev;
+ if (!netif_running(dev))
+ goto release_packet;
+ }
+
+ /* Status valid only when last descriptor bit is set. */
+ if (status.rx.last_desc && status.rx.first_desc) {
+ /*
+ * Receive without error. With receive errors
+ * disabled, packets with receive errors will be
+ * dropped, so no need to check the error bit.
+ */
+ if (!status.rx.error || (status.data &
+ KS_DESC_RX_ERROR_COND) ==
+ KS_DESC_RX_ERROR_TOO_LONG) {
+ if (rx_proc(dev, hw, desc, status))
+ goto release_packet;
+ received++;
+ } else {
+ struct dev_priv *priv = netdev_priv(dev);
+
+ /* Update receive error statistics. */
+ priv->port.counter[OID_COUNTER_RCV_ERROR]++;
+ }
+ }
+
+release_packet:
+ release_desc(desc);
+ next++;
+ next &= info->mask;
+ }
+ info->next = next;
+
+ return received;
+}
+
+static void rx_proc_task(unsigned long data)
+{
+ struct dev_info *hw_priv = (struct dev_info *) data;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ if (!hw->enabled)
+ return;
+ if (unlikely(!hw_priv->dev_rcv(hw_priv))) {
+
+ /* In case receive process is suspended because of overrun. */
+ hw_resume_rx(hw);
+
+ /* tasklets are interruptible. */
+ spin_lock_irq(&hw_priv->hwlock);
+ hw_turn_on_intr(hw, KS884X_INT_RX_MASK);
+ spin_unlock_irq(&hw_priv->hwlock);
+ } else {
+ hw_ack_intr(hw, KS884X_INT_RX);
+ tasklet_schedule(&hw_priv->rx_tasklet);
+ }
+}
+
+static void tx_proc_task(unsigned long data)
+{
+ struct dev_info *hw_priv = (struct dev_info *) data;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ hw_ack_intr(hw, KS884X_INT_TX_MASK);
+
+ tx_done(hw_priv);
+
+ /* tasklets are interruptible. */
+ spin_lock_irq(&hw_priv->hwlock);
+ hw_turn_on_intr(hw, KS884X_INT_TX);
+ spin_unlock_irq(&hw_priv->hwlock);
+}
+
+static inline void handle_rx_stop(struct ksz_hw *hw)
+{
+ /* Receive just has been stopped. */
+ if (0 == hw->rx_stop)
+ hw->intr_mask &= ~KS884X_INT_RX_STOPPED;
+ else if (hw->rx_stop > 1) {
+ if (hw->enabled && (hw->rx_cfg & DMA_RX_ENABLE)) {
+ hw_start_rx(hw);
+ } else {
+ hw->intr_mask &= ~KS884X_INT_RX_STOPPED;
+ hw->rx_stop = 0;
+ }
+ } else
+ /* Receive just has been started. */
+ hw->rx_stop++;
+}
+
+/**
+ * netdev_intr - interrupt handling
+ * @irq: Interrupt number.
+ * @dev_id: Network device.
+ *
+ * This function is called by upper network layer to signal interrupt.
+ *
+ * Return IRQ_HANDLED if interrupt is handled.
+ */
+static irqreturn_t netdev_intr(int irq, void *dev_id)
+{
+ uint int_enable = 0;
+ struct net_device *dev = (struct net_device *) dev_id;
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ hw_read_intr(hw, &int_enable);
+
+ /* Not our interrupt! */
+ if (!int_enable)
+ return IRQ_NONE;
+
+ do {
+ hw_ack_intr(hw, int_enable);
+ int_enable &= hw->intr_mask;
+
+ if (unlikely(int_enable & KS884X_INT_TX_MASK)) {
+ hw_dis_intr_bit(hw, KS884X_INT_TX_MASK);
+ tasklet_schedule(&hw_priv->tx_tasklet);
+ }
+
+ if (likely(int_enable & KS884X_INT_RX)) {
+ hw_dis_intr_bit(hw, KS884X_INT_RX);
+ tasklet_schedule(&hw_priv->rx_tasklet);
+ }
+
+ if (unlikely(int_enable & KS884X_INT_RX_OVERRUN)) {
+ dev->stats.rx_fifo_errors++;
+ hw_resume_rx(hw);
+ }
+
+ if (unlikely(int_enable & KS884X_INT_PHY)) {
+ struct ksz_port *port = &priv->port;
+
+ hw->features |= LINK_INT_WORKING;
+ port_get_link_speed(port);
+ }
+
+ if (unlikely(int_enable & KS884X_INT_RX_STOPPED)) {
+ handle_rx_stop(hw);
+ break;
+ }
+
+ if (unlikely(int_enable & KS884X_INT_TX_STOPPED)) {
+ u32 data;
+
+ hw->intr_mask &= ~KS884X_INT_TX_STOPPED;
+ pr_info("Tx stopped\n");
+ data = readl(hw->io + KS_DMA_TX_CTRL);
+ if (!(data & DMA_TX_ENABLE))
+ pr_info("Tx disabled\n");
+ break;
+ }
+ } while (0);
+
+ hw_ena_intr(hw);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * Linux network device functions
+ */
+
+static unsigned long next_jiffies;
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void netdev_netpoll(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+
+ hw_dis_intr(&hw_priv->hw);
+ netdev_intr(dev->irq, dev);
+}
+#endif
+
+static void bridge_change(struct ksz_hw *hw)
+{
+ int port;
+ u8 member;
+ struct ksz_switch *sw = hw->ksz_switch;
+
+ /* No ports in forwarding state. */
+ if (!sw->member) {
+ port_set_stp_state(hw, SWITCH_PORT_NUM, STP_STATE_SIMPLE);
+ sw_block_addr(hw);
+ }
+ for (port = 0; port < SWITCH_PORT_NUM; port++) {
+ if (STP_STATE_FORWARDING == sw->port_cfg[port].stp_state)
+ member = HOST_MASK | sw->member;
+ else
+ member = HOST_MASK | (1 << port);
+ if (member != sw->port_cfg[port].member)
+ sw_cfg_port_base_vlan(hw, port, member);
+ }
+}
+
+/**
+ * netdev_close - close network device
+ * @dev: Network device.
+ *
+ * This function process the close operation of network device. This is caused
+ * by the user command "ifconfig ethX down."
+ *
+ * Return 0 if successful; otherwise an error code indicating failure.
+ */
+static int netdev_close(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_port *port = &priv->port;
+ struct ksz_hw *hw = &hw_priv->hw;
+ int pi;
+
+ netif_stop_queue(dev);
+
+ ksz_stop_timer(&priv->monitor_timer_info);
+
+ /* Need to shut the port manually in multiple device interfaces mode. */
+ if (hw->dev_count > 1) {
+ port_set_stp_state(hw, port->first_port, STP_STATE_DISABLED);
+
+ /* Port is closed. Need to change bridge setting. */
+ if (hw->features & STP_SUPPORT) {
+ pi = 1 << port->first_port;
+ if (hw->ksz_switch->member & pi) {
+ hw->ksz_switch->member &= ~pi;
+ bridge_change(hw);
+ }
+ }
+ }
+ if (port->first_port > 0)
+ hw_del_addr(hw, dev->dev_addr);
+ if (!hw_priv->wol_enable)
+ port_set_power_saving(port, true);
+
+ if (priv->multicast)
+ --hw->all_multi;
+ if (priv->promiscuous)
+ --hw->promiscuous;
+
+ hw_priv->opened--;
+ if (!(hw_priv->opened)) {
+ ksz_stop_timer(&hw_priv->mib_timer_info);
+ flush_work(&hw_priv->mib_read);
+
+ hw_dis_intr(hw);
+ hw_disable(hw);
+ hw_clr_multicast(hw);
+
+ /* Delay for receive task to stop scheduling itself. */
+ msleep(2000 / HZ);
+
+ tasklet_disable(&hw_priv->rx_tasklet);
+ tasklet_disable(&hw_priv->tx_tasklet);
+ free_irq(dev->irq, hw_priv->dev);
+
+ transmit_cleanup(hw_priv, 0);
+ hw_reset_pkts(&hw->rx_desc_info);
+ hw_reset_pkts(&hw->tx_desc_info);
+
+ /* Clean out static MAC table when the switch is shutdown. */
+ if (hw->features & STP_SUPPORT)
+ sw_clr_sta_mac_table(hw);
+ }
+
+ return 0;
+}
+
+static void hw_cfg_huge_frame(struct dev_info *hw_priv, struct ksz_hw *hw)
+{
+ if (hw->ksz_switch) {
+ u32 data;
+
+ data = readw(hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
+ if (hw->features & RX_HUGE_FRAME)
+ data |= SWITCH_HUGE_PACKET;
+ else
+ data &= ~SWITCH_HUGE_PACKET;
+ writew(data, hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
+ }
+ if (hw->features & RX_HUGE_FRAME) {
+ hw->rx_cfg |= DMA_RX_ERROR;
+ hw_priv->dev_rcv = dev_rcv_special;
+ } else {
+ hw->rx_cfg &= ~DMA_RX_ERROR;
+ if (hw->dev_count > 1)
+ hw_priv->dev_rcv = port_rcv_packets;
+ else
+ hw_priv->dev_rcv = dev_rcv_packets;
+ }
+}
+
+static int prepare_hardware(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ int rc = 0;
+
+ /* Remember the network device that requests interrupts. */
+ hw_priv->dev = dev;
+ rc = request_irq(dev->irq, netdev_intr, IRQF_SHARED, dev->name, dev);
+ if (rc)
+ return rc;
+ tasklet_enable(&hw_priv->rx_tasklet);
+ tasklet_enable(&hw_priv->tx_tasklet);
+
+ hw->promiscuous = 0;
+ hw->all_multi = 0;
+ hw->multi_list_size = 0;
+
+ hw_reset(hw);
+
+ hw_set_desc_base(hw,
+ hw->tx_desc_info.ring_phys, hw->rx_desc_info.ring_phys);
+ hw_set_addr(hw);
+ hw_cfg_huge_frame(hw_priv, hw);
+ ksz_init_rx_buffers(hw_priv);
+ return 0;
+}
+
+static void set_media_state(struct net_device *dev, int media_state)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+
+ if (media_state == priv->media_state)
+ netif_carrier_on(dev);
+ else
+ netif_carrier_off(dev);
+ netif_info(priv, link, dev, "link %s\n",
+ media_state == priv->media_state ? "on" : "off");
+}
+
+/**
+ * netdev_open - open network device
+ * @dev: Network device.
+ *
+ * This function process the open operation of network device. This is caused
+ * by the user command "ifconfig ethX up."
+ *
+ * Return 0 if successful; otherwise an error code indicating failure.
+ */
+static int netdev_open(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_port *port = &priv->port;
+ int i;
+ int p;
+ int rc = 0;
+
+ priv->multicast = 0;
+ priv->promiscuous = 0;
+
+ /* Reset device statistics. */
+ memset(&dev->stats, 0, sizeof(struct net_device_stats));
+ memset((void *) port->counter, 0,
+ (sizeof(u64) * OID_COUNTER_LAST));
+
+ if (!(hw_priv->opened)) {
+ rc = prepare_hardware(dev);
+ if (rc)
+ return rc;
+ for (i = 0; i < hw->mib_port_cnt; i++) {
+ if (next_jiffies < jiffies)
+ next_jiffies = jiffies + HZ * 2;
+ else
+ next_jiffies += HZ * 1;
+ hw_priv->counter[i].time = next_jiffies;
+ hw->port_mib[i].state = media_disconnected;
+ port_init_cnt(hw, i);
+ }
+ if (hw->ksz_switch)
+ hw->port_mib[HOST_PORT].state = media_connected;
+ else {
+ hw_add_wol_bcast(hw);
+ hw_cfg_wol_pme(hw, 0);
+ hw_clr_wol_pme_status(&hw_priv->hw);
+ }
+ }
+ port_set_power_saving(port, false);
+
+ for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
+ /*
+ * Initialize to invalid value so that link detection
+ * is done.
+ */
+ hw->port_info[p].partner = 0xFF;
+ hw->port_info[p].state = media_disconnected;
+ }
+
+ /* Need to open the port in multiple device interfaces mode. */
+ if (hw->dev_count > 1) {
+ port_set_stp_state(hw, port->first_port, STP_STATE_SIMPLE);
+ if (port->first_port > 0)
+ hw_add_addr(hw, dev->dev_addr);
+ }
+
+ port_get_link_speed(port);
+ if (port->force_link)
+ port_force_link_speed(port);
+ else
+ port_set_link_speed(port);
+
+ if (!(hw_priv->opened)) {
+ hw_setup_intr(hw);
+ hw_enable(hw);
+ hw_ena_intr(hw);
+
+ if (hw->mib_port_cnt)
+ ksz_start_timer(&hw_priv->mib_timer_info,
+ hw_priv->mib_timer_info.period);
+ }
+
+ hw_priv->opened++;
+
+ ksz_start_timer(&priv->monitor_timer_info,
+ priv->monitor_timer_info.period);
+
+ priv->media_state = port->linked->state;
+
+ set_media_state(dev, media_connected);
+ netif_start_queue(dev);
+
+ return 0;
+}
+
+/* RX errors = rx_errors */
+/* RX dropped = rx_dropped */
+/* RX overruns = rx_fifo_errors */
+/* RX frame = rx_crc_errors + rx_frame_errors + rx_length_errors */
+/* TX errors = tx_errors */
+/* TX dropped = tx_dropped */
+/* TX overruns = tx_fifo_errors */
+/* TX carrier = tx_aborted_errors + tx_carrier_errors + tx_window_errors */
+/* collisions = collisions */
+
+/**
+ * netdev_query_statistics - query network device statistics
+ * @dev: Network device.
+ *
+ * This function returns the statistics of the network device. The device
+ * needs not be opened.
+ *
+ * Return network device statistics.
+ */
+static struct net_device_stats *netdev_query_statistics(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct ksz_port *port = &priv->port;
+ struct ksz_hw *hw = &priv->adapter->hw;
+ struct ksz_port_mib *mib;
+ int i;
+ int p;
+
+ dev->stats.rx_errors = port->counter[OID_COUNTER_RCV_ERROR];
+ dev->stats.tx_errors = port->counter[OID_COUNTER_XMIT_ERROR];
+
+ /* Reset to zero to add count later. */
+ dev->stats.multicast = 0;
+ dev->stats.collisions = 0;
+ dev->stats.rx_length_errors = 0;
+ dev->stats.rx_crc_errors = 0;
+ dev->stats.rx_frame_errors = 0;
+ dev->stats.tx_window_errors = 0;
+
+ for (i = 0, p = port->first_port; i < port->mib_port_cnt; i++, p++) {
+ mib = &hw->port_mib[p];
+
+ dev->stats.multicast += (unsigned long)
+ mib->counter[MIB_COUNTER_RX_MULTICAST];
+
+ dev->stats.collisions += (unsigned long)
+ mib->counter[MIB_COUNTER_TX_TOTAL_COLLISION];
+
+ dev->stats.rx_length_errors += (unsigned long)(
+ mib->counter[MIB_COUNTER_RX_UNDERSIZE] +
+ mib->counter[MIB_COUNTER_RX_FRAGMENT] +
+ mib->counter[MIB_COUNTER_RX_OVERSIZE] +
+ mib->counter[MIB_COUNTER_RX_JABBER]);
+ dev->stats.rx_crc_errors += (unsigned long)
+ mib->counter[MIB_COUNTER_RX_CRC_ERR];
+ dev->stats.rx_frame_errors += (unsigned long)(
+ mib->counter[MIB_COUNTER_RX_ALIGNMENT_ERR] +
+ mib->counter[MIB_COUNTER_RX_SYMBOL_ERR]);
+
+ dev->stats.tx_window_errors += (unsigned long)
+ mib->counter[MIB_COUNTER_TX_LATE_COLLISION];
+ }
+
+ return &dev->stats;
+}
+
+/**
+ * netdev_set_mac_address - set network device MAC address
+ * @dev: Network device.
+ * @addr: Buffer of MAC address.
+ *
+ * This function is used to set the MAC address of the network device.
+ *
+ * Return 0 to indicate success.
+ */
+static int netdev_set_mac_address(struct net_device *dev, void *addr)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct sockaddr *mac = addr;
+ uint interrupt;
+
+ if (priv->port.first_port > 0)
+ hw_del_addr(hw, dev->dev_addr);
+ else {
+ hw->mac_override = 1;
+ memcpy(hw->override_addr, mac->sa_data, MAC_ADDR_LEN);
+ }
+
+ memcpy(dev->dev_addr, mac->sa_data, MAX_ADDR_LEN);
+
+ interrupt = hw_block_intr(hw);
+
+ if (priv->port.first_port > 0)
+ hw_add_addr(hw, dev->dev_addr);
+ else
+ hw_set_addr(hw);
+ hw_restore_intr(hw, interrupt);
+
+ return 0;
+}
+
+static void dev_set_promiscuous(struct net_device *dev, struct dev_priv *priv,
+ struct ksz_hw *hw, int promiscuous)
+{
+ if (promiscuous != priv->promiscuous) {
+ u8 prev_state = hw->promiscuous;
+
+ if (promiscuous)
+ ++hw->promiscuous;
+ else
+ --hw->promiscuous;
+ priv->promiscuous = promiscuous;
+
+ /* Turn on/off promiscuous mode. */
+ if (hw->promiscuous <= 1 && prev_state <= 1)
+ hw_set_promiscuous(hw, hw->promiscuous);
+
+ /*
+ * Port is not in promiscuous mode, meaning it is released
+ * from the bridge.
+ */
+ if ((hw->features & STP_SUPPORT) && !promiscuous &&
+ (dev->priv_flags & IFF_BRIDGE_PORT)) {
+ struct ksz_switch *sw = hw->ksz_switch;
+ int port = priv->port.first_port;
+
+ port_set_stp_state(hw, port, STP_STATE_DISABLED);
+ port = 1 << port;
+ if (sw->member & port) {
+ sw->member &= ~port;
+ bridge_change(hw);
+ }
+ }
+ }
+}
+
+static void dev_set_multicast(struct dev_priv *priv, struct ksz_hw *hw,
+ int multicast)
+{
+ if (multicast != priv->multicast) {
+ u8 all_multi = hw->all_multi;
+
+ if (multicast)
+ ++hw->all_multi;
+ else
+ --hw->all_multi;
+ priv->multicast = multicast;
+
+ /* Turn on/off all multicast mode. */
+ if (hw->all_multi <= 1 && all_multi <= 1)
+ hw_set_multicast(hw, hw->all_multi);
+ }
+}
+
+/**
+ * netdev_set_rx_mode
+ * @dev: Network device.
+ *
+ * This routine is used to set multicast addresses or put the network device
+ * into promiscuous mode.
+ */
+static void netdev_set_rx_mode(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct netdev_hw_addr *ha;
+ int multicast = (dev->flags & IFF_ALLMULTI);
+
+ dev_set_promiscuous(dev, priv, hw, (dev->flags & IFF_PROMISC));
+
+ if (hw_priv->hw.dev_count > 1)
+ multicast |= (dev->flags & IFF_MULTICAST);
+ dev_set_multicast(priv, hw, multicast);
+
+ /* Cannot use different hashes in multiple device interfaces mode. */
+ if (hw_priv->hw.dev_count > 1)
+ return;
+
+ if ((dev->flags & IFF_MULTICAST) && !netdev_mc_empty(dev)) {
+ int i = 0;
+
+ /* List too big to support so turn on all multicast mode. */
+ if (netdev_mc_count(dev) > MAX_MULTICAST_LIST) {
+ if (MAX_MULTICAST_LIST != hw->multi_list_size) {
+ hw->multi_list_size = MAX_MULTICAST_LIST;
+ ++hw->all_multi;
+ hw_set_multicast(hw, hw->all_multi);
+ }
+ return;
+ }
+
+ netdev_for_each_mc_addr(ha, dev) {
+ if (i >= MAX_MULTICAST_LIST)
+ break;
+ memcpy(hw->multi_list[i++], ha->addr, MAC_ADDR_LEN);
+ }
+ hw->multi_list_size = (u8) i;
+ hw_set_grp_addr(hw);
+ } else {
+ if (MAX_MULTICAST_LIST == hw->multi_list_size) {
+ --hw->all_multi;
+ hw_set_multicast(hw, hw->all_multi);
+ }
+ hw->multi_list_size = 0;
+ hw_clr_multicast(hw);
+ }
+}
+
+static int netdev_change_mtu(struct net_device *dev, int new_mtu)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ int hw_mtu;
+
+ if (netif_running(dev))
+ return -EBUSY;
+
+ /* Cannot use different MTU in multiple device interfaces mode. */
+ if (hw->dev_count > 1)
+ if (dev != hw_priv->dev)
+ return 0;
+ if (new_mtu < 60)
+ return -EINVAL;
+
+ if (dev->mtu != new_mtu) {
+ hw_mtu = new_mtu + ETHERNET_HEADER_SIZE + 4;
+ if (hw_mtu > MAX_RX_BUF_SIZE)
+ return -EINVAL;
+ if (hw_mtu > REGULAR_RX_BUF_SIZE) {
+ hw->features |= RX_HUGE_FRAME;
+ hw_mtu = MAX_RX_BUF_SIZE;
+ } else {
+ hw->features &= ~RX_HUGE_FRAME;
+ hw_mtu = REGULAR_RX_BUF_SIZE;
+ }
+ hw_mtu = (hw_mtu + 3) & ~3;
+ hw_priv->mtu = hw_mtu;
+ dev->mtu = new_mtu;
+ }
+ return 0;
+}
+
+/**
+ * netdev_ioctl - I/O control processing
+ * @dev: Network device.
+ * @ifr: Interface request structure.
+ * @cmd: I/O control code.
+ *
+ * This function is used to process I/O control calls.
+ *
+ * Return 0 to indicate success.
+ */
+static int netdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_port *port = &priv->port;
+ int rc;
+ int result = 0;
+ struct mii_ioctl_data *data = if_mii(ifr);
+
+ if (down_interruptible(&priv->proc_sem))
+ return -ERESTARTSYS;
+
+ /* assume success */
+ rc = 0;
+ switch (cmd) {
+ /* Get address of MII PHY in use. */
+ case SIOCGMIIPHY:
+ data->phy_id = priv->id;
+
+ /* Fallthrough... */
+
+ /* Read MII PHY register. */
+ case SIOCGMIIREG:
+ if (data->phy_id != priv->id || data->reg_num >= 6)
+ result = -EIO;
+ else
+ hw_r_phy(hw, port->linked->port_id, data->reg_num,
+ &data->val_out);
+ break;
+
+ /* Write MII PHY register. */
+ case SIOCSMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ result = -EPERM;
+ else if (data->phy_id != priv->id || data->reg_num >= 6)
+ result = -EIO;
+ else
+ hw_w_phy(hw, port->linked->port_id, data->reg_num,
+ data->val_in);
+ break;
+
+ default:
+ result = -EOPNOTSUPP;
+ }
+
+ up(&priv->proc_sem);
+
+ return result;
+}
+
+/*
+ * MII support
+ */
+
+/**
+ * mdio_read - read PHY register
+ * @dev: Network device.
+ * @phy_id: The PHY id.
+ * @reg_num: The register number.
+ *
+ * This function returns the PHY register value.
+ *
+ * Return the register value.
+ */
+static int mdio_read(struct net_device *dev, int phy_id, int reg_num)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct ksz_port *port = &priv->port;
+ struct ksz_hw *hw = port->hw;
+ u16 val_out;
+
+ hw_r_phy(hw, port->linked->port_id, reg_num << 1, &val_out);
+ return val_out;
+}
+
+/**
+ * mdio_write - set PHY register
+ * @dev: Network device.
+ * @phy_id: The PHY id.
+ * @reg_num: The register number.
+ * @val: The register value.
+ *
+ * This procedure sets the PHY register value.
+ */
+static void mdio_write(struct net_device *dev, int phy_id, int reg_num, int val)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct ksz_port *port = &priv->port;
+ struct ksz_hw *hw = port->hw;
+ int i;
+ int pi;
+
+ for (i = 0, pi = port->first_port; i < port->port_cnt; i++, pi++)
+ hw_w_phy(hw, pi, reg_num << 1, val);
+}
+
+/*
+ * ethtool support
+ */
+
+#define EEPROM_SIZE 0x40
+
+static u16 eeprom_data[EEPROM_SIZE] = { 0 };
+
+#define ADVERTISED_ALL \
+ (ADVERTISED_10baseT_Half | \
+ ADVERTISED_10baseT_Full | \
+ ADVERTISED_100baseT_Half | \
+ ADVERTISED_100baseT_Full)
+
+/* These functions use the MII functions in mii.c. */
+
+/**
+ * netdev_get_settings - get network device settings
+ * @dev: Network device.
+ * @cmd: Ethtool command.
+ *
+ * This function queries the PHY and returns its state in the ethtool command.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+
+ mutex_lock(&hw_priv->lock);
+ mii_ethtool_gset(&priv->mii_if, cmd);
+ cmd->advertising |= SUPPORTED_TP;
+ mutex_unlock(&hw_priv->lock);
+
+ /* Save advertised settings for workaround in next function. */
+ priv->advertising = cmd->advertising;
+ return 0;
+}
+
+/**
+ * netdev_set_settings - set network device settings
+ * @dev: Network device.
+ * @cmd: Ethtool command.
+ *
+ * This function sets the PHY according to the ethtool command.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_port *port = &priv->port;
+ u32 speed = ethtool_cmd_speed(cmd);
+ int rc;
+
+ /*
+ * ethtool utility does not change advertised setting if auto
+ * negotiation is not specified explicitly.
+ */
+ if (cmd->autoneg && priv->advertising == cmd->advertising) {
+ cmd->advertising |= ADVERTISED_ALL;
+ if (10 == speed)
+ cmd->advertising &=
+ ~(ADVERTISED_100baseT_Full |
+ ADVERTISED_100baseT_Half);
+ else if (100 == speed)
+ cmd->advertising &=
+ ~(ADVERTISED_10baseT_Full |
+ ADVERTISED_10baseT_Half);
+ if (0 == cmd->duplex)
+ cmd->advertising &=
+ ~(ADVERTISED_100baseT_Full |
+ ADVERTISED_10baseT_Full);
+ else if (1 == cmd->duplex)
+ cmd->advertising &=
+ ~(ADVERTISED_100baseT_Half |
+ ADVERTISED_10baseT_Half);
+ }
+ mutex_lock(&hw_priv->lock);
+ if (cmd->autoneg &&
+ (cmd->advertising & ADVERTISED_ALL) ==
+ ADVERTISED_ALL) {
+ port->duplex = 0;
+ port->speed = 0;
+ port->force_link = 0;
+ } else {
+ port->duplex = cmd->duplex + 1;
+ if (1000 != speed)
+ port->speed = speed;
+ if (cmd->autoneg)
+ port->force_link = 0;
+ else
+ port->force_link = 1;
+ }
+ rc = mii_ethtool_sset(&priv->mii_if, cmd);
+ mutex_unlock(&hw_priv->lock);
+ return rc;
+}
+
+/**
+ * netdev_nway_reset - restart auto-negotiation
+ * @dev: Network device.
+ *
+ * This function restarts the PHY for auto-negotiation.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_nway_reset(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ int rc;
+
+ mutex_lock(&hw_priv->lock);
+ rc = mii_nway_restart(&priv->mii_if);
+ mutex_unlock(&hw_priv->lock);
+ return rc;
+}
+
+/**
+ * netdev_get_link - get network device link status
+ * @dev: Network device.
+ *
+ * This function gets the link status from the PHY.
+ *
+ * Return true if PHY is linked and false otherwise.
+ */
+static u32 netdev_get_link(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ int rc;
+
+ rc = mii_link_ok(&priv->mii_if);
+ return rc;
+}
+
+/**
+ * netdev_get_drvinfo - get network driver information
+ * @dev: Network device.
+ * @info: Ethtool driver info data structure.
+ *
+ * This procedure returns the driver information.
+ */
+static void netdev_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+
+ strcpy(info->driver, DRV_NAME);
+ strcpy(info->version, DRV_VERSION);
+ strcpy(info->bus_info, pci_name(hw_priv->pdev));
+}
+
+/**
+ * netdev_get_regs_len - get length of register dump
+ * @dev: Network device.
+ *
+ * This function returns the length of the register dump.
+ *
+ * Return length of the register dump.
+ */
+static struct hw_regs {
+ int start;
+ int end;
+} hw_regs_range[] = {
+ { KS_DMA_TX_CTRL, KS884X_INTERRUPTS_STATUS },
+ { KS_ADD_ADDR_0_LO, KS_ADD_ADDR_F_HI },
+ { KS884X_ADDR_0_OFFSET, KS8841_WOL_FRAME_BYTE2_OFFSET },
+ { KS884X_SIDER_P, KS8842_SGCR7_P },
+ { KS8842_MACAR1_P, KS8842_TOSR8_P },
+ { KS884X_P1MBCR_P, KS8842_P3ERCR_P },
+ { 0, 0 }
+};
+
+static int netdev_get_regs_len(struct net_device *dev)
+{
+ struct hw_regs *range = hw_regs_range;
+ int regs_len = 0x10 * sizeof(u32);
+
+ while (range->end > range->start) {
+ regs_len += (range->end - range->start + 3) / 4 * 4;
+ range++;
+ }
+ return regs_len;
+}
+
+/**
+ * netdev_get_regs - get register dump
+ * @dev: Network device.
+ * @regs: Ethtool registers data structure.
+ * @ptr: Buffer to store the register values.
+ *
+ * This procedure dumps the register values in the provided buffer.
+ */
+static void netdev_get_regs(struct net_device *dev, struct ethtool_regs *regs,
+ void *ptr)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ int *buf = (int *) ptr;
+ struct hw_regs *range = hw_regs_range;
+ int len;
+
+ mutex_lock(&hw_priv->lock);
+ regs->version = 0;
+ for (len = 0; len < 0x40; len += 4) {
+ pci_read_config_dword(hw_priv->pdev, len, buf);
+ buf++;
+ }
+ while (range->end > range->start) {
+ for (len = range->start; len < range->end; len += 4) {
+ *buf = readl(hw->io + len);
+ buf++;
+ }
+ range++;
+ }
+ mutex_unlock(&hw_priv->lock);
+}
+
+#define WOL_SUPPORT \
+ (WAKE_PHY | WAKE_MAGIC | \
+ WAKE_UCAST | WAKE_MCAST | \
+ WAKE_BCAST | WAKE_ARP)
+
+/**
+ * netdev_get_wol - get Wake-on-LAN support
+ * @dev: Network device.
+ * @wol: Ethtool Wake-on-LAN data structure.
+ *
+ * This procedure returns Wake-on-LAN support.
+ */
+static void netdev_get_wol(struct net_device *dev,
+ struct ethtool_wolinfo *wol)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+
+ wol->supported = hw_priv->wol_support;
+ wol->wolopts = hw_priv->wol_enable;
+ memset(&wol->sopass, 0, sizeof(wol->sopass));
+}
+
+/**
+ * netdev_set_wol - set Wake-on-LAN support
+ * @dev: Network device.
+ * @wol: Ethtool Wake-on-LAN data structure.
+ *
+ * This function sets Wake-on-LAN support.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_set_wol(struct net_device *dev,
+ struct ethtool_wolinfo *wol)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+
+ /* Need to find a way to retrieve the device IP address. */
+ static const u8 net_addr[] = { 192, 168, 1, 1 };
+
+ if (wol->wolopts & ~hw_priv->wol_support)
+ return -EINVAL;
+
+ hw_priv->wol_enable = wol->wolopts;
+
+ /* Link wakeup cannot really be disabled. */
+ if (wol->wolopts)
+ hw_priv->wol_enable |= WAKE_PHY;
+ hw_enable_wol(&hw_priv->hw, hw_priv->wol_enable, net_addr);
+ return 0;
+}
+
+/**
+ * netdev_get_msglevel - get debug message level
+ * @dev: Network device.
+ *
+ * This function returns current debug message level.
+ *
+ * Return current debug message flags.
+ */
+static u32 netdev_get_msglevel(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+
+ return priv->msg_enable;
+}
+
+/**
+ * netdev_set_msglevel - set debug message level
+ * @dev: Network device.
+ * @value: Debug message flags.
+ *
+ * This procedure sets debug message level.
+ */
+static void netdev_set_msglevel(struct net_device *dev, u32 value)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+
+ priv->msg_enable = value;
+}
+
+/**
+ * netdev_get_eeprom_len - get EEPROM length
+ * @dev: Network device.
+ *
+ * This function returns the length of the EEPROM.
+ *
+ * Return length of the EEPROM.
+ */
+static int netdev_get_eeprom_len(struct net_device *dev)
+{
+ return EEPROM_SIZE * 2;
+}
+
+/**
+ * netdev_get_eeprom - get EEPROM data
+ * @dev: Network device.
+ * @eeprom: Ethtool EEPROM data structure.
+ * @data: Buffer to store the EEPROM data.
+ *
+ * This function dumps the EEPROM data in the provided buffer.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+#define EEPROM_MAGIC 0x10A18842
+
+static int netdev_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ u8 *eeprom_byte = (u8 *) eeprom_data;
+ int i;
+ int len;
+
+ len = (eeprom->offset + eeprom->len + 1) / 2;
+ for (i = eeprom->offset / 2; i < len; i++)
+ eeprom_data[i] = eeprom_read(&hw_priv->hw, i);
+ eeprom->magic = EEPROM_MAGIC;
+ memcpy(data, &eeprom_byte[eeprom->offset], eeprom->len);
+
+ return 0;
+}
+
+/**
+ * netdev_set_eeprom - write EEPROM data
+ * @dev: Network device.
+ * @eeprom: Ethtool EEPROM data structure.
+ * @data: Data buffer.
+ *
+ * This function modifies the EEPROM data one byte at a time.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_set_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ u16 eeprom_word[EEPROM_SIZE];
+ u8 *eeprom_byte = (u8 *) eeprom_word;
+ int i;
+ int len;
+
+ if (eeprom->magic != EEPROM_MAGIC)
+ return -EINVAL;
+
+ len = (eeprom->offset + eeprom->len + 1) / 2;
+ for (i = eeprom->offset / 2; i < len; i++)
+ eeprom_data[i] = eeprom_read(&hw_priv->hw, i);
+ memcpy(eeprom_word, eeprom_data, EEPROM_SIZE * 2);
+ memcpy(&eeprom_byte[eeprom->offset], data, eeprom->len);
+ for (i = 0; i < EEPROM_SIZE; i++)
+ if (eeprom_word[i] != eeprom_data[i]) {
+ eeprom_data[i] = eeprom_word[i];
+ eeprom_write(&hw_priv->hw, i, eeprom_data[i]);
+ }
+
+ return 0;
+}
+
+/**
+ * netdev_get_pauseparam - get flow control parameters
+ * @dev: Network device.
+ * @pause: Ethtool PAUSE settings data structure.
+ *
+ * This procedure returns the PAUSE control flow settings.
+ */
+static void netdev_get_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *pause)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ pause->autoneg = (hw->overrides & PAUSE_FLOW_CTRL) ? 0 : 1;
+ if (!hw->ksz_switch) {
+ pause->rx_pause =
+ (hw->rx_cfg & DMA_RX_FLOW_ENABLE) ? 1 : 0;
+ pause->tx_pause =
+ (hw->tx_cfg & DMA_TX_FLOW_ENABLE) ? 1 : 0;
+ } else {
+ pause->rx_pause =
+ (sw_chk(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_RX_FLOW_CTRL)) ? 1 : 0;
+ pause->tx_pause =
+ (sw_chk(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_TX_FLOW_CTRL)) ? 1 : 0;
+ }
+}
+
+/**
+ * netdev_set_pauseparam - set flow control parameters
+ * @dev: Network device.
+ * @pause: Ethtool PAUSE settings data structure.
+ *
+ * This function sets the PAUSE control flow settings.
+ * Not implemented yet.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_set_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *pause)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_port *port = &priv->port;
+
+ mutex_lock(&hw_priv->lock);
+ if (pause->autoneg) {
+ if (!pause->rx_pause && !pause->tx_pause)
+ port->flow_ctrl = PHY_NO_FLOW_CTRL;
+ else
+ port->flow_ctrl = PHY_FLOW_CTRL;
+ hw->overrides &= ~PAUSE_FLOW_CTRL;
+ port->force_link = 0;
+ if (hw->ksz_switch) {
+ sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_RX_FLOW_CTRL, 1);
+ sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_TX_FLOW_CTRL, 1);
+ }
+ port_set_link_speed(port);
+ } else {
+ hw->overrides |= PAUSE_FLOW_CTRL;
+ if (hw->ksz_switch) {
+ sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_RX_FLOW_CTRL, pause->rx_pause);
+ sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
+ SWITCH_TX_FLOW_CTRL, pause->tx_pause);
+ } else
+ set_flow_ctrl(hw, pause->rx_pause, pause->tx_pause);
+ }
+ mutex_unlock(&hw_priv->lock);
+
+ return 0;
+}
+
+/**
+ * netdev_get_ringparam - get tx/rx ring parameters
+ * @dev: Network device.
+ * @pause: Ethtool RING settings data structure.
+ *
+ * This procedure returns the TX/RX ring settings.
+ */
+static void netdev_get_ringparam(struct net_device *dev,
+ struct ethtool_ringparam *ring)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ ring->tx_max_pending = (1 << 9);
+ ring->tx_pending = hw->tx_desc_info.alloc;
+ ring->rx_max_pending = (1 << 9);
+ ring->rx_pending = hw->rx_desc_info.alloc;
+}
+
+#define STATS_LEN (TOTAL_PORT_COUNTER_NUM)
+
+static struct {
+ char string[ETH_GSTRING_LEN];
+} ethtool_stats_keys[STATS_LEN] = {
+ { "rx_lo_priority_octets" },
+ { "rx_hi_priority_octets" },
+ { "rx_undersize_packets" },
+ { "rx_fragments" },
+ { "rx_oversize_packets" },
+ { "rx_jabbers" },
+ { "rx_symbol_errors" },
+ { "rx_crc_errors" },
+ { "rx_align_errors" },
+ { "rx_mac_ctrl_packets" },
+ { "rx_pause_packets" },
+ { "rx_bcast_packets" },
+ { "rx_mcast_packets" },
+ { "rx_ucast_packets" },
+ { "rx_64_or_less_octet_packets" },
+ { "rx_65_to_127_octet_packets" },
+ { "rx_128_to_255_octet_packets" },
+ { "rx_256_to_511_octet_packets" },
+ { "rx_512_to_1023_octet_packets" },
+ { "rx_1024_to_1522_octet_packets" },
+
+ { "tx_lo_priority_octets" },
+ { "tx_hi_priority_octets" },
+ { "tx_late_collisions" },
+ { "tx_pause_packets" },
+ { "tx_bcast_packets" },
+ { "tx_mcast_packets" },
+ { "tx_ucast_packets" },
+ { "tx_deferred" },
+ { "tx_total_collisions" },
+ { "tx_excessive_collisions" },
+ { "tx_single_collisions" },
+ { "tx_mult_collisions" },
+
+ { "rx_discards" },
+ { "tx_discards" },
+};
+
+/**
+ * netdev_get_strings - get statistics identity strings
+ * @dev: Network device.
+ * @stringset: String set identifier.
+ * @buf: Buffer to store the strings.
+ *
+ * This procedure returns the strings used to identify the statistics.
+ */
+static void netdev_get_strings(struct net_device *dev, u32 stringset, u8 *buf)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ if (ETH_SS_STATS == stringset)
+ memcpy(buf, ðtool_stats_keys,
+ ETH_GSTRING_LEN * hw->mib_cnt);
+}
+
+/**
+ * netdev_get_sset_count - get statistics size
+ * @dev: Network device.
+ * @sset: The statistics set number.
+ *
+ * This function returns the size of the statistics to be reported.
+ *
+ * Return size of the statistics to be reported.
+ */
+static int netdev_get_sset_count(struct net_device *dev, int sset)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ switch (sset) {
+ case ETH_SS_STATS:
+ return hw->mib_cnt;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+/**
+ * netdev_get_ethtool_stats - get network device statistics
+ * @dev: Network device.
+ * @stats: Ethtool statistics data structure.
+ * @data: Buffer to store the statistics.
+ *
+ * This procedure returns the statistics.
+ */
+static void netdev_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_port *port = &priv->port;
+ int n_stats = stats->n_stats;
+ int i;
+ int n;
+ int p;
+ int rc;
+ u64 counter[TOTAL_PORT_COUNTER_NUM];
+
+ mutex_lock(&hw_priv->lock);
+ n = SWITCH_PORT_NUM;
+ for (i = 0, p = port->first_port; i < port->mib_port_cnt; i++, p++) {
+ if (media_connected == hw->port_mib[p].state) {
+ hw_priv->counter[p].read = 1;
+
+ /* Remember first port that requests read. */
+ if (n == SWITCH_PORT_NUM)
+ n = p;
+ }
+ }
+ mutex_unlock(&hw_priv->lock);
+
+ if (n < SWITCH_PORT_NUM)
+ schedule_work(&hw_priv->mib_read);
+
+ if (1 == port->mib_port_cnt && n < SWITCH_PORT_NUM) {
+ p = n;
+ rc = wait_event_interruptible_timeout(
+ hw_priv->counter[p].counter,
+ 2 == hw_priv->counter[p].read,
+ HZ * 1);
+ } else
+ for (i = 0, p = n; i < port->mib_port_cnt - n; i++, p++) {
+ if (0 == i) {
+ rc = wait_event_interruptible_timeout(
+ hw_priv->counter[p].counter,
+ 2 == hw_priv->counter[p].read,
+ HZ * 2);
+ } else if (hw->port_mib[p].cnt_ptr) {
+ rc = wait_event_interruptible_timeout(
+ hw_priv->counter[p].counter,
+ 2 == hw_priv->counter[p].read,
+ HZ * 1);
+ }
+ }
+
+ get_mib_counters(hw, port->first_port, port->mib_port_cnt, counter);
+ n = hw->mib_cnt;
+ if (n > n_stats)
+ n = n_stats;
+ n_stats -= n;
+ for (i = 0; i < n; i++)
+ *data++ = counter[i];
+}
+
+/**
+ * netdev_set_features - set receive checksum support
+ * @dev: Network device.
+ * @features: New device features (offloads).
+ *
+ * This function sets receive checksum support setting.
+ *
+ * Return 0 if successful; otherwise an error code.
+ */
+static int netdev_set_features(struct net_device *dev, u32 features)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ mutex_lock(&hw_priv->lock);
+
+ /* see note in hw_setup() */
+ if (features & NETIF_F_RXCSUM)
+ hw->rx_cfg |= DMA_RX_CSUM_TCP | DMA_RX_CSUM_IP;
+ else
+ hw->rx_cfg &= ~(DMA_RX_CSUM_TCP | DMA_RX_CSUM_IP);
+
+ if (hw->enabled)
+ writel(hw->rx_cfg, hw->io + KS_DMA_RX_CTRL);
+
+ mutex_unlock(&hw_priv->lock);
+
+ return 0;
+}
+
+static struct ethtool_ops netdev_ethtool_ops = {
+ .get_settings = netdev_get_settings,
+ .set_settings = netdev_set_settings,
+ .nway_reset = netdev_nway_reset,
+ .get_link = netdev_get_link,
+ .get_drvinfo = netdev_get_drvinfo,
+ .get_regs_len = netdev_get_regs_len,
+ .get_regs = netdev_get_regs,
+ .get_wol = netdev_get_wol,
+ .set_wol = netdev_set_wol,
+ .get_msglevel = netdev_get_msglevel,
+ .set_msglevel = netdev_set_msglevel,
+ .get_eeprom_len = netdev_get_eeprom_len,
+ .get_eeprom = netdev_get_eeprom,
+ .set_eeprom = netdev_set_eeprom,
+ .get_pauseparam = netdev_get_pauseparam,
+ .set_pauseparam = netdev_set_pauseparam,
+ .get_ringparam = netdev_get_ringparam,
+ .get_strings = netdev_get_strings,
+ .get_sset_count = netdev_get_sset_count,
+ .get_ethtool_stats = netdev_get_ethtool_stats,
+};
+
+/*
+ * Hardware monitoring
+ */
+
+static void update_link(struct net_device *dev, struct dev_priv *priv,
+ struct ksz_port *port)
+{
+ if (priv->media_state != port->linked->state) {
+ priv->media_state = port->linked->state;
+ if (netif_running(dev))
+ set_media_state(dev, media_connected);
+ }
+}
+
+static void mib_read_work(struct work_struct *work)
+{
+ struct dev_info *hw_priv =
+ container_of(work, struct dev_info, mib_read);
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_port_mib *mib;
+ int i;
+
+ next_jiffies = jiffies;
+ for (i = 0; i < hw->mib_port_cnt; i++) {
+ mib = &hw->port_mib[i];
+
+ /* Reading MIB counters or requested to read. */
+ if (mib->cnt_ptr || 1 == hw_priv->counter[i].read) {
+
+ /* Need to process receive interrupt. */
+ if (port_r_cnt(hw, i))
+ break;
+ hw_priv->counter[i].read = 0;
+
+ /* Finish reading counters. */
+ if (0 == mib->cnt_ptr) {
+ hw_priv->counter[i].read = 2;
+ wake_up_interruptible(
+ &hw_priv->counter[i].counter);
+ }
+ } else if (jiffies >= hw_priv->counter[i].time) {
+ /* Only read MIB counters when the port is connected. */
+ if (media_connected == mib->state)
+ hw_priv->counter[i].read = 1;
+ next_jiffies += HZ * 1 * hw->mib_port_cnt;
+ hw_priv->counter[i].time = next_jiffies;
+
+ /* Port is just disconnected. */
+ } else if (mib->link_down) {
+ mib->link_down = 0;
+
+ /* Read counters one last time after link is lost. */
+ hw_priv->counter[i].read = 1;
+ }
+ }
+}
+
+static void mib_monitor(unsigned long ptr)
+{
+ struct dev_info *hw_priv = (struct dev_info *) ptr;
+
+ mib_read_work(&hw_priv->mib_read);
+
+ /* This is used to verify Wake-on-LAN is working. */
+ if (hw_priv->pme_wait) {
+ if (hw_priv->pme_wait <= jiffies) {
+ hw_clr_wol_pme_status(&hw_priv->hw);
+ hw_priv->pme_wait = 0;
+ }
+ } else if (hw_chk_wol_pme_status(&hw_priv->hw)) {
+
+ /* PME is asserted. Wait 2 seconds to clear it. */
+ hw_priv->pme_wait = jiffies + HZ * 2;
+ }
+
+ ksz_update_timer(&hw_priv->mib_timer_info);
+}
+
+/**
+ * dev_monitor - periodic monitoring
+ * @ptr: Network device pointer.
+ *
+ * This routine is run in a kernel timer to monitor the network device.
+ */
+static void dev_monitor(unsigned long ptr)
+{
+ struct net_device *dev = (struct net_device *) ptr;
+ struct dev_priv *priv = netdev_priv(dev);
+ struct dev_info *hw_priv = priv->adapter;
+ struct ksz_hw *hw = &hw_priv->hw;
+ struct ksz_port *port = &priv->port;
+
+ if (!(hw->features & LINK_INT_WORKING))
+ port_get_link_speed(port);
+ update_link(dev, priv, port);
+
+ ksz_update_timer(&priv->monitor_timer_info);
+}
+
+/*
+ * Linux network device interface functions
+ */
+
+/* Driver exported variables */
+
+static int msg_enable;
+
+static char *macaddr = ":";
+static char *mac1addr = ":";
+
+/*
+ * This enables multiple network device mode for KSZ8842, which contains a
+ * switch with two physical ports. Some users like to take control of the
+ * ports for running Spanning Tree Protocol. The driver will create an
+ * additional eth? device for the other port.
+ *
+ * Some limitations are the network devices cannot have different MTU and
+ * multicast hash tables.
+ */
+static int multi_dev;
+
+/*
+ * As most users select multiple network device mode to use Spanning Tree
+ * Protocol, this enables a feature in which most unicast and multicast packets
+ * are forwarded inside the switch and not passed to the host. Only packets
+ * that need the host's attention are passed to it. This prevents the host
+ * wasting CPU time to examine each and every incoming packets and do the
+ * forwarding itself.
+ *
+ * As the hack requires the private bridge header, the driver cannot compile
+ * with just the kernel headers.
+ *
+ * Enabling STP support also turns on multiple network device mode.
+ */
+static int stp;
+
+/*
+ * This enables fast aging in the KSZ8842 switch. Not sure what situation
+ * needs that. However, fast aging is used to flush the dynamic MAC table when
+ * STP suport is enabled.
+ */
+static int fast_aging;
+
+/**
+ * netdev_init - initialize network device.
+ * @dev: Network device.
+ *
+ * This function initializes the network device.
+ *
+ * Return 0 if successful; otherwise an error code indicating failure.
+ */
+static int __init netdev_init(struct net_device *dev)
+{
+ struct dev_priv *priv = netdev_priv(dev);
+
+ /* 500 ms timeout */
+ ksz_init_timer(&priv->monitor_timer_info, 500 * HZ / 1000,
+ dev_monitor, dev);
+
+ /* 500 ms timeout */
+ dev->watchdog_timeo = HZ / 2;
+
+ dev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_RXCSUM;
+
+ /*
+ * Hardware does not really support IPv6 checksum generation, but
+ * driver actually runs faster with this on.
+ */
+ dev->hw_features |= NETIF_F_IPV6_CSUM;
+
+ dev->features |= dev->hw_features;
+
+ sema_init(&priv->proc_sem, 1);
+
+ priv->mii_if.phy_id_mask = 0x1;
+ priv->mii_if.reg_num_mask = 0x7;
+ priv->mii_if.dev = dev;
+ priv->mii_if.mdio_read = mdio_read;
+ priv->mii_if.mdio_write = mdio_write;
+ priv->mii_if.phy_id = priv->port.first_port + 1;
+
+ priv->msg_enable = netif_msg_init(msg_enable,
+ (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK));
+
+ return 0;
+}
+
+static const struct net_device_ops netdev_ops = {
+ .ndo_init = netdev_init,
+ .ndo_open = netdev_open,
+ .ndo_stop = netdev_close,
+ .ndo_get_stats = netdev_query_statistics,
+ .ndo_start_xmit = netdev_tx,
+ .ndo_tx_timeout = netdev_tx_timeout,
+ .ndo_change_mtu = netdev_change_mtu,
+ .ndo_set_features = netdev_set_features,
+ .ndo_set_mac_address = netdev_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_do_ioctl = netdev_ioctl,
+ .ndo_set_rx_mode = netdev_set_rx_mode,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = netdev_netpoll,
+#endif
+};
+
+static void netdev_free(struct net_device *dev)
+{
+ if (dev->watchdog_timeo)
+ unregister_netdev(dev);
+
+ free_netdev(dev);
+}
+
+struct platform_info {
+ struct dev_info dev_info;
+ struct net_device *netdev[SWITCH_PORT_NUM];
+};
+
+static int net_device_present;
+
+static void get_mac_addr(struct dev_info *hw_priv, u8 *macaddr, int port)
+{
+ int i;
+ int j;
+ int got_num;
+ int num;
+
+ i = j = num = got_num = 0;
+ while (j < MAC_ADDR_LEN) {
+ if (macaddr[i]) {
+ int digit;
+
+ got_num = 1;
+ digit = hex_to_bin(macaddr[i]);
+ if (digit >= 0)
+ num = num * 16 + digit;
+ else if (':' == macaddr[i])
+ got_num = 2;
+ else
+ break;
+ } else if (got_num)
+ got_num = 2;
+ else
+ break;
+ if (2 == got_num) {
+ if (MAIN_PORT == port) {
+ hw_priv->hw.override_addr[j++] = (u8) num;
+ hw_priv->hw.override_addr[5] +=
+ hw_priv->hw.id;
+ } else {
+ hw_priv->hw.ksz_switch->other_addr[j++] =
+ (u8) num;
+ hw_priv->hw.ksz_switch->other_addr[5] +=
+ hw_priv->hw.id;
+ }
+ num = got_num = 0;
+ }
+ i++;
+ }
+ if (MAC_ADDR_LEN == j) {
+ if (MAIN_PORT == port)
+ hw_priv->hw.mac_override = 1;
+ }
+}
+
+#define KS884X_DMA_MASK (~0x0UL)
+
+static void read_other_addr(struct ksz_hw *hw)
+{
+ int i;
+ u16 data[3];
+ struct ksz_switch *sw = hw->ksz_switch;
+
+ for (i = 0; i < 3; i++)
+ data[i] = eeprom_read(hw, i + EEPROM_DATA_OTHER_MAC_ADDR);
+ if ((data[0] || data[1] || data[2]) && data[0] != 0xffff) {
+ sw->other_addr[5] = (u8) data[0];
+ sw->other_addr[4] = (u8)(data[0] >> 8);
+ sw->other_addr[3] = (u8) data[1];
+ sw->other_addr[2] = (u8)(data[1] >> 8);
+ sw->other_addr[1] = (u8) data[2];
+ sw->other_addr[0] = (u8)(data[2] >> 8);
+ }
+}
+
+#ifndef PCI_VENDOR_ID_MICREL_KS
+#define PCI_VENDOR_ID_MICREL_KS 0x16c6
+#endif
+
+static int __devinit pcidev_init(struct pci_dev *pdev,
+ const struct pci_device_id *id)
+{
+ struct net_device *dev;
+ struct dev_priv *priv;
+ struct dev_info *hw_priv;
+ struct ksz_hw *hw;
+ struct platform_info *info;
+ struct ksz_port *port;
+ unsigned long reg_base;
+ unsigned long reg_len;
+ int cnt;
+ int i;
+ int mib_port_count;
+ int pi;
+ int port_count;
+ int result;
+ char banner[sizeof(version)];
+ struct ksz_switch *sw = NULL;
+
+ result = pci_enable_device(pdev);
+ if (result)
+ return result;
+
+ result = -ENODEV;
+
+ if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32)) ||
+ pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)))
+ return result;
+
+ reg_base = pci_resource_start(pdev, 0);
+ reg_len = pci_resource_len(pdev, 0);
+ if ((pci_resource_flags(pdev, 0) & IORESOURCE_IO) != 0)
+ return result;
+
+ if (!request_mem_region(reg_base, reg_len, DRV_NAME))
+ return result;
+ pci_set_master(pdev);
+
+ result = -ENOMEM;
+
+ info = kzalloc(sizeof(struct platform_info), GFP_KERNEL);
+ if (!info)
+ goto pcidev_init_dev_err;
+
+ hw_priv = &info->dev_info;
+ hw_priv->pdev = pdev;
+
+ hw = &hw_priv->hw;
+
+ hw->io = ioremap(reg_base, reg_len);
+ if (!hw->io)
+ goto pcidev_init_io_err;
+
+ cnt = hw_init(hw);
+ if (!cnt) {
+ if (msg_enable & NETIF_MSG_PROBE)
+ pr_alert("chip not detected\n");
+ result = -ENODEV;
+ goto pcidev_init_alloc_err;
+ }
+
+ snprintf(banner, sizeof(banner), "%s", version);
+ banner[13] = cnt + '0'; /* Replace x in "Micrel KSZ884x" */
+ dev_info(&hw_priv->pdev->dev, "%s\n", banner);
+ dev_dbg(&hw_priv->pdev->dev, "Mem = %p; IRQ = %d\n", hw->io, pdev->irq);
+
+ /* Assume device is KSZ8841. */
+ hw->dev_count = 1;
+ port_count = 1;
+ mib_port_count = 1;
+ hw->addr_list_size = 0;
+ hw->mib_cnt = PORT_COUNTER_NUM;
+ hw->mib_port_cnt = 1;
+
+ /* KSZ8842 has a switch with multiple ports. */
+ if (2 == cnt) {
+ if (fast_aging)
+ hw->overrides |= FAST_AGING;
+
+ hw->mib_cnt = TOTAL_PORT_COUNTER_NUM;
+
+ /* Multiple network device interfaces are required. */
+ if (multi_dev) {
+ hw->dev_count = SWITCH_PORT_NUM;
+ hw->addr_list_size = SWITCH_PORT_NUM - 1;
+ }
+
+ /* Single network device has multiple ports. */
+ if (1 == hw->dev_count) {
+ port_count = SWITCH_PORT_NUM;
+ mib_port_count = SWITCH_PORT_NUM;
+ }
+ hw->mib_port_cnt = TOTAL_PORT_NUM;
+ hw->ksz_switch = kzalloc(sizeof(struct ksz_switch), GFP_KERNEL);
+ if (!hw->ksz_switch)
+ goto pcidev_init_alloc_err;
+
+ sw = hw->ksz_switch;
+ }
+ for (i = 0; i < hw->mib_port_cnt; i++)
+ hw->port_mib[i].mib_start = 0;
+
+ hw->parent = hw_priv;
+
+ /* Default MTU is 1500. */
+ hw_priv->mtu = (REGULAR_RX_BUF_SIZE + 3) & ~3;
+
+ if (ksz_alloc_mem(hw_priv))
+ goto pcidev_init_mem_err;
+
+ hw_priv->hw.id = net_device_present;
+
+ spin_lock_init(&hw_priv->hwlock);
+ mutex_init(&hw_priv->lock);
+
+ /* tasklet is enabled. */
+ tasklet_init(&hw_priv->rx_tasklet, rx_proc_task,
+ (unsigned long) hw_priv);
+ tasklet_init(&hw_priv->tx_tasklet, tx_proc_task,
+ (unsigned long) hw_priv);
+
+ /* tasklet_enable will decrement the atomic counter. */
+ tasklet_disable(&hw_priv->rx_tasklet);
+ tasklet_disable(&hw_priv->tx_tasklet);
+
+ for (i = 0; i < TOTAL_PORT_NUM; i++)
+ init_waitqueue_head(&hw_priv->counter[i].counter);
+
+ if (macaddr[0] != ':')
+ get_mac_addr(hw_priv, macaddr, MAIN_PORT);
+
+ /* Read MAC address and initialize override address if not overrided. */
+ hw_read_addr(hw);
+
+ /* Multiple device interfaces mode requires a second MAC address. */
+ if (hw->dev_count > 1) {
+ memcpy(sw->other_addr, hw->override_addr, MAC_ADDR_LEN);
+ read_other_addr(hw);
+ if (mac1addr[0] != ':')
+ get_mac_addr(hw_priv, mac1addr, OTHER_PORT);
+ }
+
+ hw_setup(hw);
+ if (hw->ksz_switch)
+ sw_setup(hw);
+ else {
+ hw_priv->wol_support = WOL_SUPPORT;
+ hw_priv->wol_enable = 0;
+ }
+
+ INIT_WORK(&hw_priv->mib_read, mib_read_work);
+
+ /* 500 ms timeout */
+ ksz_init_timer(&hw_priv->mib_timer_info, 500 * HZ / 1000,
+ mib_monitor, hw_priv);
+
+ for (i = 0; i < hw->dev_count; i++) {
+ dev = alloc_etherdev(sizeof(struct dev_priv));
+ if (!dev)
+ goto pcidev_init_reg_err;
+ info->netdev[i] = dev;
+
+ priv = netdev_priv(dev);
+ priv->adapter = hw_priv;
+ priv->id = net_device_present++;
+
+ port = &priv->port;
+ port->port_cnt = port_count;
+ port->mib_port_cnt = mib_port_count;
+ port->first_port = i;
+ port->flow_ctrl = PHY_FLOW_CTRL;
+
+ port->hw = hw;
+ port->linked = &hw->port_info[port->first_port];
+
+ for (cnt = 0, pi = i; cnt < port_count; cnt++, pi++) {
+ hw->port_info[pi].port_id = pi;
+ hw->port_info[pi].pdev = dev;
+ hw->port_info[pi].state = media_disconnected;
+ }
+
+ dev->mem_start = (unsigned long) hw->io;
+ dev->mem_end = dev->mem_start + reg_len - 1;
+ dev->irq = pdev->irq;
+ if (MAIN_PORT == i)
+ memcpy(dev->dev_addr, hw_priv->hw.override_addr,
+ MAC_ADDR_LEN);
+ else {
+ memcpy(dev->dev_addr, sw->other_addr,
+ MAC_ADDR_LEN);
+ if (!memcmp(sw->other_addr, hw->override_addr,
+ MAC_ADDR_LEN))
+ dev->dev_addr[5] += port->first_port;
+ }
+
+ dev->netdev_ops = &netdev_ops;
+ SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
+ if (register_netdev(dev))
+ goto pcidev_init_reg_err;
+ port_set_power_saving(port, true);
+ }
+
+ pci_dev_get(hw_priv->pdev);
+ pci_set_drvdata(pdev, info);
+ return 0;
+
+pcidev_init_reg_err:
+ for (i = 0; i < hw->dev_count; i++) {
+ if (info->netdev[i]) {
+ netdev_free(info->netdev[i]);
+ info->netdev[i] = NULL;
+ }
+ }
+
+pcidev_init_mem_err:
+ ksz_free_mem(hw_priv);
+ kfree(hw->ksz_switch);
+
+pcidev_init_alloc_err:
+ iounmap(hw->io);
+
+pcidev_init_io_err:
+ kfree(info);
+
+pcidev_init_dev_err:
+ release_mem_region(reg_base, reg_len);
+
+ return result;
+}
+
+static void pcidev_exit(struct pci_dev *pdev)
+{
+ int i;
+ struct platform_info *info = pci_get_drvdata(pdev);
+ struct dev_info *hw_priv = &info->dev_info;
+
+ pci_set_drvdata(pdev, NULL);
+
+ release_mem_region(pci_resource_start(pdev, 0),
+ pci_resource_len(pdev, 0));
+ for (i = 0; i < hw_priv->hw.dev_count; i++) {
+ if (info->netdev[i])
+ netdev_free(info->netdev[i]);
+ }
+ if (hw_priv->hw.io)
+ iounmap(hw_priv->hw.io);
+ ksz_free_mem(hw_priv);
+ kfree(hw_priv->hw.ksz_switch);
+ pci_dev_put(hw_priv->pdev);
+ kfree(info);
+}
+
+#ifdef CONFIG_PM
+static int pcidev_resume(struct pci_dev *pdev)
+{
+ int i;
+ struct platform_info *info = pci_get_drvdata(pdev);
+ struct dev_info *hw_priv = &info->dev_info;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ pci_enable_wake(pdev, PCI_D0, 0);
+
+ if (hw_priv->wol_enable)
+ hw_cfg_wol_pme(hw, 0);
+ for (i = 0; i < hw->dev_count; i++) {
+ if (info->netdev[i]) {
+ struct net_device *dev = info->netdev[i];
+
+ if (netif_running(dev)) {
+ netdev_open(dev);
+ netif_device_attach(dev);
+ }
+ }
+ }
+ return 0;
+}
+
+static int pcidev_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int i;
+ struct platform_info *info = pci_get_drvdata(pdev);
+ struct dev_info *hw_priv = &info->dev_info;
+ struct ksz_hw *hw = &hw_priv->hw;
+
+ /* Need to find a way to retrieve the device IP address. */
+ static const u8 net_addr[] = { 192, 168, 1, 1 };
+
+ for (i = 0; i < hw->dev_count; i++) {
+ if (info->netdev[i]) {
+ struct net_device *dev = info->netdev[i];
+
+ if (netif_running(dev)) {
+ netif_device_detach(dev);
+ netdev_close(dev);
+ }
+ }
+ }
+ if (hw_priv->wol_enable) {
+ hw_enable_wol(hw, hw_priv->wol_enable, net_addr);
+ hw_cfg_wol_pme(hw, 1);
+ }
+
+ pci_save_state(pdev);
+ pci_enable_wake(pdev, pci_choose_state(pdev, state), 1);
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ return 0;
+}
+#endif
+
+static char pcidev_name[] = "ksz884xp";
+
+static struct pci_device_id pcidev_table[] = {
+ { PCI_VENDOR_ID_MICREL_KS, 0x8841,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { PCI_VENDOR_ID_MICREL_KS, 0x8842,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { 0 }
+};
+
+MODULE_DEVICE_TABLE(pci, pcidev_table);
+
+static struct pci_driver pci_device_driver = {
+#ifdef CONFIG_PM
+ .suspend = pcidev_suspend,
+ .resume = pcidev_resume,
+#endif
+ .name = pcidev_name,
+ .id_table = pcidev_table,
+ .probe = pcidev_init,
+ .remove = pcidev_exit
+};
+
+static int __init ksz884x_init_module(void)
+{
+ return pci_register_driver(&pci_device_driver);
+}
+
+static void __exit ksz884x_cleanup_module(void)
+{
+ pci_unregister_driver(&pci_device_driver);
+}
+
+module_init(ksz884x_init_module);
+module_exit(ksz884x_cleanup_module);
+
+MODULE_DESCRIPTION("KSZ8841/2 PCI network driver");
+MODULE_AUTHOR("Tristram Ha <Tristram.Ha@micrel.com>");
+MODULE_LICENSE("GPL");
+
+module_param_named(message, msg_enable, int, 0);
+MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
+
+module_param(macaddr, charp, 0);
+module_param(mac1addr, charp, 0);
+module_param(fast_aging, int, 0);
+module_param(multi_dev, int, 0);
+module_param(stp, int, 0);
+MODULE_PARM_DESC(macaddr, "MAC address");
+MODULE_PARM_DESC(mac1addr, "Second MAC address");
+MODULE_PARM_DESC(fast_aging, "Fast aging");
+MODULE_PARM_DESC(multi_dev, "Multiple device interfaces");
+MODULE_PARM_DESC(stp, "STP support");
+++ /dev/null
-/*
- * ks8842.c timberdale KS8842 ethernet driver
- * Copyright (c) 2009 Intel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/* Supports:
- * The Micrel KS8842 behind the timberdale FPGA
- * The genuine Micrel KS8841/42 device with ISA 16/32bit bus interface
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/ethtool.h>
-#include <linux/ks8842.h>
-#include <linux/dmaengine.h>
-#include <linux/dma-mapping.h>
-#include <linux/scatterlist.h>
-
-#define DRV_NAME "ks8842"
-
-/* Timberdale specific Registers */
-#define REG_TIMB_RST 0x1c
-#define REG_TIMB_FIFO 0x20
-#define REG_TIMB_ISR 0x24
-#define REG_TIMB_IER 0x28
-#define REG_TIMB_IAR 0x2C
-#define REQ_TIMB_DMA_RESUME 0x30
-
-/* KS8842 registers */
-
-#define REG_SELECT_BANK 0x0e
-
-/* bank 0 registers */
-#define REG_QRFCR 0x04
-
-/* bank 2 registers */
-#define REG_MARL 0x00
-#define REG_MARM 0x02
-#define REG_MARH 0x04
-
-/* bank 3 registers */
-#define REG_GRR 0x06
-
-/* bank 16 registers */
-#define REG_TXCR 0x00
-#define REG_TXSR 0x02
-#define REG_RXCR 0x04
-#define REG_TXMIR 0x08
-#define REG_RXMIR 0x0A
-
-/* bank 17 registers */
-#define REG_TXQCR 0x00
-#define REG_RXQCR 0x02
-#define REG_TXFDPR 0x04
-#define REG_RXFDPR 0x06
-#define REG_QMU_DATA_LO 0x08
-#define REG_QMU_DATA_HI 0x0A
-
-/* bank 18 registers */
-#define REG_IER 0x00
-#define IRQ_LINK_CHANGE 0x8000
-#define IRQ_TX 0x4000
-#define IRQ_RX 0x2000
-#define IRQ_RX_OVERRUN 0x0800
-#define IRQ_TX_STOPPED 0x0200
-#define IRQ_RX_STOPPED 0x0100
-#define IRQ_RX_ERROR 0x0080
-#define ENABLED_IRQS (IRQ_LINK_CHANGE | IRQ_TX | IRQ_RX | IRQ_RX_STOPPED | \
- IRQ_TX_STOPPED | IRQ_RX_OVERRUN | IRQ_RX_ERROR)
-/* When running via timberdale in DMA mode, the RX interrupt should be
- enabled in the KS8842, but not in the FPGA IP, since the IP handles
- RX DMA internally.
- TX interrupts are not needed it is handled by the FPGA the driver is
- notified via DMA callbacks.
-*/
-#define ENABLED_IRQS_DMA_IP (IRQ_LINK_CHANGE | IRQ_RX_STOPPED | \
- IRQ_TX_STOPPED | IRQ_RX_OVERRUN | IRQ_RX_ERROR)
-#define ENABLED_IRQS_DMA (ENABLED_IRQS_DMA_IP | IRQ_RX)
-#define REG_ISR 0x02
-#define REG_RXSR 0x04
-#define RXSR_VALID 0x8000
-#define RXSR_BROADCAST 0x80
-#define RXSR_MULTICAST 0x40
-#define RXSR_UNICAST 0x20
-#define RXSR_FRAMETYPE 0x08
-#define RXSR_TOO_LONG 0x04
-#define RXSR_RUNT 0x02
-#define RXSR_CRC_ERROR 0x01
-#define RXSR_ERROR (RXSR_TOO_LONG | RXSR_RUNT | RXSR_CRC_ERROR)
-
-/* bank 32 registers */
-#define REG_SW_ID_AND_ENABLE 0x00
-#define REG_SGCR1 0x02
-#define REG_SGCR2 0x04
-#define REG_SGCR3 0x06
-
-/* bank 39 registers */
-#define REG_MACAR1 0x00
-#define REG_MACAR2 0x02
-#define REG_MACAR3 0x04
-
-/* bank 45 registers */
-#define REG_P1MBCR 0x00
-#define REG_P1MBSR 0x02
-
-/* bank 46 registers */
-#define REG_P2MBCR 0x00
-#define REG_P2MBSR 0x02
-
-/* bank 48 registers */
-#define REG_P1CR2 0x02
-
-/* bank 49 registers */
-#define REG_P1CR4 0x02
-#define REG_P1SR 0x04
-
-/* flags passed by platform_device for configuration */
-#define MICREL_KS884X 0x01 /* 0=Timeberdale(FPGA), 1=Micrel */
-#define KS884X_16BIT 0x02 /* 1=16bit, 0=32bit */
-
-#define DMA_BUFFER_SIZE 2048
-
-struct ks8842_tx_dma_ctl {
- struct dma_chan *chan;
- struct dma_async_tx_descriptor *adesc;
- void *buf;
- struct scatterlist sg;
- int channel;
-};
-
-struct ks8842_rx_dma_ctl {
- struct dma_chan *chan;
- struct dma_async_tx_descriptor *adesc;
- struct sk_buff *skb;
- struct scatterlist sg;
- struct tasklet_struct tasklet;
- int channel;
-};
-
-#define KS8842_USE_DMA(adapter) (((adapter)->dma_tx.channel != -1) && \
- ((adapter)->dma_rx.channel != -1))
-
-struct ks8842_adapter {
- void __iomem *hw_addr;
- int irq;
- unsigned long conf_flags; /* copy of platform_device config */
- struct tasklet_struct tasklet;
- spinlock_t lock; /* spinlock to be interrupt safe */
- struct work_struct timeout_work;
- struct net_device *netdev;
- struct device *dev;
- struct ks8842_tx_dma_ctl dma_tx;
- struct ks8842_rx_dma_ctl dma_rx;
-};
-
-static void ks8842_dma_rx_cb(void *data);
-static void ks8842_dma_tx_cb(void *data);
-
-static inline void ks8842_resume_dma(struct ks8842_adapter *adapter)
-{
- iowrite32(1, adapter->hw_addr + REQ_TIMB_DMA_RESUME);
-}
-
-static inline void ks8842_select_bank(struct ks8842_adapter *adapter, u16 bank)
-{
- iowrite16(bank, adapter->hw_addr + REG_SELECT_BANK);
-}
-
-static inline void ks8842_write8(struct ks8842_adapter *adapter, u16 bank,
- u8 value, int offset)
-{
- ks8842_select_bank(adapter, bank);
- iowrite8(value, adapter->hw_addr + offset);
-}
-
-static inline void ks8842_write16(struct ks8842_adapter *adapter, u16 bank,
- u16 value, int offset)
-{
- ks8842_select_bank(adapter, bank);
- iowrite16(value, adapter->hw_addr + offset);
-}
-
-static inline void ks8842_enable_bits(struct ks8842_adapter *adapter, u16 bank,
- u16 bits, int offset)
-{
- u16 reg;
- ks8842_select_bank(adapter, bank);
- reg = ioread16(adapter->hw_addr + offset);
- reg |= bits;
- iowrite16(reg, adapter->hw_addr + offset);
-}
-
-static inline void ks8842_clear_bits(struct ks8842_adapter *adapter, u16 bank,
- u16 bits, int offset)
-{
- u16 reg;
- ks8842_select_bank(adapter, bank);
- reg = ioread16(adapter->hw_addr + offset);
- reg &= ~bits;
- iowrite16(reg, adapter->hw_addr + offset);
-}
-
-static inline void ks8842_write32(struct ks8842_adapter *adapter, u16 bank,
- u32 value, int offset)
-{
- ks8842_select_bank(adapter, bank);
- iowrite32(value, adapter->hw_addr + offset);
-}
-
-static inline u8 ks8842_read8(struct ks8842_adapter *adapter, u16 bank,
- int offset)
-{
- ks8842_select_bank(adapter, bank);
- return ioread8(adapter->hw_addr + offset);
-}
-
-static inline u16 ks8842_read16(struct ks8842_adapter *adapter, u16 bank,
- int offset)
-{
- ks8842_select_bank(adapter, bank);
- return ioread16(adapter->hw_addr + offset);
-}
-
-static inline u32 ks8842_read32(struct ks8842_adapter *adapter, u16 bank,
- int offset)
-{
- ks8842_select_bank(adapter, bank);
- return ioread32(adapter->hw_addr + offset);
-}
-
-static void ks8842_reset(struct ks8842_adapter *adapter)
-{
- if (adapter->conf_flags & MICREL_KS884X) {
- ks8842_write16(adapter, 3, 1, REG_GRR);
- msleep(10);
- iowrite16(0, adapter->hw_addr + REG_GRR);
- } else {
- /* The KS8842 goes haywire when doing softare reset
- * a work around in the timberdale IP is implemented to
- * do a hardware reset instead
- ks8842_write16(adapter, 3, 1, REG_GRR);
- msleep(10);
- iowrite16(0, adapter->hw_addr + REG_GRR);
- */
- iowrite32(0x1, adapter->hw_addr + REG_TIMB_RST);
- msleep(20);
- }
-}
-
-static void ks8842_update_link_status(struct net_device *netdev,
- struct ks8842_adapter *adapter)
-{
- /* check the status of the link */
- if (ks8842_read16(adapter, 45, REG_P1MBSR) & 0x4) {
- netif_carrier_on(netdev);
- netif_wake_queue(netdev);
- } else {
- netif_stop_queue(netdev);
- netif_carrier_off(netdev);
- }
-}
-
-static void ks8842_enable_tx(struct ks8842_adapter *adapter)
-{
- ks8842_enable_bits(adapter, 16, 0x01, REG_TXCR);
-}
-
-static void ks8842_disable_tx(struct ks8842_adapter *adapter)
-{
- ks8842_clear_bits(adapter, 16, 0x01, REG_TXCR);
-}
-
-static void ks8842_enable_rx(struct ks8842_adapter *adapter)
-{
- ks8842_enable_bits(adapter, 16, 0x01, REG_RXCR);
-}
-
-static void ks8842_disable_rx(struct ks8842_adapter *adapter)
-{
- ks8842_clear_bits(adapter, 16, 0x01, REG_RXCR);
-}
-
-static void ks8842_reset_hw(struct ks8842_adapter *adapter)
-{
- /* reset the HW */
- ks8842_reset(adapter);
-
- /* Enable QMU Transmit flow control / transmit padding / Transmit CRC */
- ks8842_write16(adapter, 16, 0x000E, REG_TXCR);
-
- /* enable the receiver, uni + multi + broadcast + flow ctrl
- + crc strip */
- ks8842_write16(adapter, 16, 0x8 | 0x20 | 0x40 | 0x80 | 0x400,
- REG_RXCR);
-
- /* TX frame pointer autoincrement */
- ks8842_write16(adapter, 17, 0x4000, REG_TXFDPR);
-
- /* RX frame pointer autoincrement */
- ks8842_write16(adapter, 17, 0x4000, REG_RXFDPR);
-
- /* RX 2 kb high watermark */
- ks8842_write16(adapter, 0, 0x1000, REG_QRFCR);
-
- /* aggressive back off in half duplex */
- ks8842_enable_bits(adapter, 32, 1 << 8, REG_SGCR1);
-
- /* enable no excessive collison drop */
- ks8842_enable_bits(adapter, 32, 1 << 3, REG_SGCR2);
-
- /* Enable port 1 force flow control / back pressure / transmit / recv */
- ks8842_write16(adapter, 48, 0x1E07, REG_P1CR2);
-
- /* restart port auto-negotiation */
- ks8842_enable_bits(adapter, 49, 1 << 13, REG_P1CR4);
-
- /* Enable the transmitter */
- ks8842_enable_tx(adapter);
-
- /* Enable the receiver */
- ks8842_enable_rx(adapter);
-
- /* clear all interrupts */
- ks8842_write16(adapter, 18, 0xffff, REG_ISR);
-
- /* enable interrupts */
- if (KS8842_USE_DMA(adapter)) {
- /* When running in DMA Mode the RX interrupt is not enabled in
- timberdale because RX data is received by DMA callbacks
- it must still be enabled in the KS8842 because it indicates
- to timberdale when there is RX data for it's DMA FIFOs */
- iowrite16(ENABLED_IRQS_DMA_IP, adapter->hw_addr + REG_TIMB_IER);
- ks8842_write16(adapter, 18, ENABLED_IRQS_DMA, REG_IER);
- } else {
- if (!(adapter->conf_flags & MICREL_KS884X))
- iowrite16(ENABLED_IRQS,
- adapter->hw_addr + REG_TIMB_IER);
- ks8842_write16(adapter, 18, ENABLED_IRQS, REG_IER);
- }
- /* enable the switch */
- ks8842_write16(adapter, 32, 0x1, REG_SW_ID_AND_ENABLE);
-}
-
-static void ks8842_read_mac_addr(struct ks8842_adapter *adapter, u8 *dest)
-{
- int i;
- u16 mac;
-
- for (i = 0; i < ETH_ALEN; i++)
- dest[ETH_ALEN - i - 1] = ks8842_read8(adapter, 2, REG_MARL + i);
-
- if (adapter->conf_flags & MICREL_KS884X) {
- /*
- the sequence of saving mac addr between MAC and Switch is
- different.
- */
-
- mac = ks8842_read16(adapter, 2, REG_MARL);
- ks8842_write16(adapter, 39, mac, REG_MACAR3);
- mac = ks8842_read16(adapter, 2, REG_MARM);
- ks8842_write16(adapter, 39, mac, REG_MACAR2);
- mac = ks8842_read16(adapter, 2, REG_MARH);
- ks8842_write16(adapter, 39, mac, REG_MACAR1);
- } else {
-
- /* make sure the switch port uses the same MAC as the QMU */
- mac = ks8842_read16(adapter, 2, REG_MARL);
- ks8842_write16(adapter, 39, mac, REG_MACAR1);
- mac = ks8842_read16(adapter, 2, REG_MARM);
- ks8842_write16(adapter, 39, mac, REG_MACAR2);
- mac = ks8842_read16(adapter, 2, REG_MARH);
- ks8842_write16(adapter, 39, mac, REG_MACAR3);
- }
-}
-
-static void ks8842_write_mac_addr(struct ks8842_adapter *adapter, u8 *mac)
-{
- unsigned long flags;
- unsigned i;
-
- spin_lock_irqsave(&adapter->lock, flags);
- for (i = 0; i < ETH_ALEN; i++) {
- ks8842_write8(adapter, 2, mac[ETH_ALEN - i - 1], REG_MARL + i);
- if (!(adapter->conf_flags & MICREL_KS884X))
- ks8842_write8(adapter, 39, mac[ETH_ALEN - i - 1],
- REG_MACAR1 + i);
- }
-
- if (adapter->conf_flags & MICREL_KS884X) {
- /*
- the sequence of saving mac addr between MAC and Switch is
- different.
- */
-
- u16 mac;
-
- mac = ks8842_read16(adapter, 2, REG_MARL);
- ks8842_write16(adapter, 39, mac, REG_MACAR3);
- mac = ks8842_read16(adapter, 2, REG_MARM);
- ks8842_write16(adapter, 39, mac, REG_MACAR2);
- mac = ks8842_read16(adapter, 2, REG_MARH);
- ks8842_write16(adapter, 39, mac, REG_MACAR1);
- }
- spin_unlock_irqrestore(&adapter->lock, flags);
-}
-
-static inline u16 ks8842_tx_fifo_space(struct ks8842_adapter *adapter)
-{
- return ks8842_read16(adapter, 16, REG_TXMIR) & 0x1fff;
-}
-
-static int ks8842_tx_frame_dma(struct sk_buff *skb, struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct ks8842_tx_dma_ctl *ctl = &adapter->dma_tx;
- u8 *buf = ctl->buf;
-
- if (ctl->adesc) {
- netdev_dbg(netdev, "%s: TX ongoing\n", __func__);
- /* transfer ongoing */
- return NETDEV_TX_BUSY;
- }
-
- sg_dma_len(&ctl->sg) = skb->len + sizeof(u32);
-
- /* copy data to the TX buffer */
- /* the control word, enable IRQ, port 1 and the length */
- *buf++ = 0x00;
- *buf++ = 0x01; /* Port 1 */
- *buf++ = skb->len & 0xff;
- *buf++ = (skb->len >> 8) & 0xff;
- skb_copy_from_linear_data(skb, buf, skb->len);
-
- dma_sync_single_range_for_device(adapter->dev,
- sg_dma_address(&ctl->sg), 0, sg_dma_len(&ctl->sg),
- DMA_TO_DEVICE);
-
- /* make sure the length is a multiple of 4 */
- if (sg_dma_len(&ctl->sg) % 4)
- sg_dma_len(&ctl->sg) += 4 - sg_dma_len(&ctl->sg) % 4;
-
- ctl->adesc = ctl->chan->device->device_prep_slave_sg(ctl->chan,
- &ctl->sg, 1, DMA_TO_DEVICE,
- DMA_PREP_INTERRUPT | DMA_COMPL_SKIP_SRC_UNMAP);
- if (!ctl->adesc)
- return NETDEV_TX_BUSY;
-
- ctl->adesc->callback_param = netdev;
- ctl->adesc->callback = ks8842_dma_tx_cb;
- ctl->adesc->tx_submit(ctl->adesc);
-
- netdev->stats.tx_bytes += skb->len;
-
- dev_kfree_skb(skb);
-
- return NETDEV_TX_OK;
-}
-
-static int ks8842_tx_frame(struct sk_buff *skb, struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- int len = skb->len;
-
- netdev_dbg(netdev, "%s: len %u head %p data %p tail %p end %p\n",
- __func__, skb->len, skb->head, skb->data,
- skb_tail_pointer(skb), skb_end_pointer(skb));
-
- /* check FIFO buffer space, we need space for CRC and command bits */
- if (ks8842_tx_fifo_space(adapter) < len + 8)
- return NETDEV_TX_BUSY;
-
- if (adapter->conf_flags & KS884X_16BIT) {
- u16 *ptr16 = (u16 *)skb->data;
- ks8842_write16(adapter, 17, 0x8000 | 0x100, REG_QMU_DATA_LO);
- ks8842_write16(adapter, 17, (u16)len, REG_QMU_DATA_HI);
- netdev->stats.tx_bytes += len;
-
- /* copy buffer */
- while (len > 0) {
- iowrite16(*ptr16++, adapter->hw_addr + REG_QMU_DATA_LO);
- iowrite16(*ptr16++, adapter->hw_addr + REG_QMU_DATA_HI);
- len -= sizeof(u32);
- }
- } else {
-
- u32 *ptr = (u32 *)skb->data;
- u32 ctrl;
- /* the control word, enable IRQ, port 1 and the length */
- ctrl = 0x8000 | 0x100 | (len << 16);
- ks8842_write32(adapter, 17, ctrl, REG_QMU_DATA_LO);
-
- netdev->stats.tx_bytes += len;
-
- /* copy buffer */
- while (len > 0) {
- iowrite32(*ptr, adapter->hw_addr + REG_QMU_DATA_LO);
- len -= sizeof(u32);
- ptr++;
- }
- }
-
- /* enqueue packet */
- ks8842_write16(adapter, 17, 1, REG_TXQCR);
-
- dev_kfree_skb(skb);
-
- return NETDEV_TX_OK;
-}
-
-static void ks8842_update_rx_err_counters(struct net_device *netdev, u32 status)
-{
- netdev_dbg(netdev, "RX error, status: %x\n", status);
-
- netdev->stats.rx_errors++;
- if (status & RXSR_TOO_LONG)
- netdev->stats.rx_length_errors++;
- if (status & RXSR_CRC_ERROR)
- netdev->stats.rx_crc_errors++;
- if (status & RXSR_RUNT)
- netdev->stats.rx_frame_errors++;
-}
-
-static void ks8842_update_rx_counters(struct net_device *netdev, u32 status,
- int len)
-{
- netdev_dbg(netdev, "RX packet, len: %d\n", len);
-
- netdev->stats.rx_packets++;
- netdev->stats.rx_bytes += len;
- if (status & RXSR_MULTICAST)
- netdev->stats.multicast++;
-}
-
-static int __ks8842_start_new_rx_dma(struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct ks8842_rx_dma_ctl *ctl = &adapter->dma_rx;
- struct scatterlist *sg = &ctl->sg;
- int err;
-
- ctl->skb = netdev_alloc_skb(netdev, DMA_BUFFER_SIZE);
- if (ctl->skb) {
- sg_init_table(sg, 1);
- sg_dma_address(sg) = dma_map_single(adapter->dev,
- ctl->skb->data, DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
- err = dma_mapping_error(adapter->dev, sg_dma_address(sg));
- if (unlikely(err)) {
- sg_dma_address(sg) = 0;
- goto out;
- }
-
- sg_dma_len(sg) = DMA_BUFFER_SIZE;
-
- ctl->adesc = ctl->chan->device->device_prep_slave_sg(ctl->chan,
- sg, 1, DMA_FROM_DEVICE,
- DMA_PREP_INTERRUPT | DMA_COMPL_SKIP_SRC_UNMAP);
-
- if (!ctl->adesc)
- goto out;
-
- ctl->adesc->callback_param = netdev;
- ctl->adesc->callback = ks8842_dma_rx_cb;
- ctl->adesc->tx_submit(ctl->adesc);
- } else {
- err = -ENOMEM;
- sg_dma_address(sg) = 0;
- goto out;
- }
-
- return err;
-out:
- if (sg_dma_address(sg))
- dma_unmap_single(adapter->dev, sg_dma_address(sg),
- DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
- sg_dma_address(sg) = 0;
- if (ctl->skb)
- dev_kfree_skb(ctl->skb);
-
- ctl->skb = NULL;
-
- printk(KERN_ERR DRV_NAME": Failed to start RX DMA: %d\n", err);
- return err;
-}
-
-static void ks8842_rx_frame_dma_tasklet(unsigned long arg)
-{
- struct net_device *netdev = (struct net_device *)arg;
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct ks8842_rx_dma_ctl *ctl = &adapter->dma_rx;
- struct sk_buff *skb = ctl->skb;
- dma_addr_t addr = sg_dma_address(&ctl->sg);
- u32 status;
-
- ctl->adesc = NULL;
-
- /* kick next transfer going */
- __ks8842_start_new_rx_dma(netdev);
-
- /* now handle the data we got */
- dma_unmap_single(adapter->dev, addr, DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
-
- status = *((u32 *)skb->data);
-
- netdev_dbg(netdev, "%s - rx_data: status: %x\n",
- __func__, status & 0xffff);
-
- /* check the status */
- if ((status & RXSR_VALID) && !(status & RXSR_ERROR)) {
- int len = (status >> 16) & 0x7ff;
-
- ks8842_update_rx_counters(netdev, status, len);
-
- /* reserve 4 bytes which is the status word */
- skb_reserve(skb, 4);
- skb_put(skb, len);
-
- skb->protocol = eth_type_trans(skb, netdev);
- netif_rx(skb);
- } else {
- ks8842_update_rx_err_counters(netdev, status);
- dev_kfree_skb(skb);
- }
-}
-
-static void ks8842_rx_frame(struct net_device *netdev,
- struct ks8842_adapter *adapter)
-{
- u32 status;
- int len;
-
- if (adapter->conf_flags & KS884X_16BIT) {
- status = ks8842_read16(adapter, 17, REG_QMU_DATA_LO);
- len = ks8842_read16(adapter, 17, REG_QMU_DATA_HI);
- netdev_dbg(netdev, "%s - rx_data: status: %x\n",
- __func__, status);
- } else {
- status = ks8842_read32(adapter, 17, REG_QMU_DATA_LO);
- len = (status >> 16) & 0x7ff;
- status &= 0xffff;
- netdev_dbg(netdev, "%s - rx_data: status: %x\n",
- __func__, status);
- }
-
- /* check the status */
- if ((status & RXSR_VALID) && !(status & RXSR_ERROR)) {
- struct sk_buff *skb = netdev_alloc_skb_ip_align(netdev, len + 3);
-
- if (skb) {
-
- ks8842_update_rx_counters(netdev, status, len);
-
- if (adapter->conf_flags & KS884X_16BIT) {
- u16 *data16 = (u16 *)skb_put(skb, len);
- ks8842_select_bank(adapter, 17);
- while (len > 0) {
- *data16++ = ioread16(adapter->hw_addr +
- REG_QMU_DATA_LO);
- *data16++ = ioread16(adapter->hw_addr +
- REG_QMU_DATA_HI);
- len -= sizeof(u32);
- }
- } else {
- u32 *data = (u32 *)skb_put(skb, len);
-
- ks8842_select_bank(adapter, 17);
- while (len > 0) {
- *data++ = ioread32(adapter->hw_addr +
- REG_QMU_DATA_LO);
- len -= sizeof(u32);
- }
- }
- skb->protocol = eth_type_trans(skb, netdev);
- netif_rx(skb);
- } else
- netdev->stats.rx_dropped++;
- } else
- ks8842_update_rx_err_counters(netdev, status);
-
- /* set high watermark to 3K */
- ks8842_clear_bits(adapter, 0, 1 << 12, REG_QRFCR);
-
- /* release the frame */
- ks8842_write16(adapter, 17, 0x01, REG_RXQCR);
-
- /* set high watermark to 2K */
- ks8842_enable_bits(adapter, 0, 1 << 12, REG_QRFCR);
-}
-
-void ks8842_handle_rx(struct net_device *netdev, struct ks8842_adapter *adapter)
-{
- u16 rx_data = ks8842_read16(adapter, 16, REG_RXMIR) & 0x1fff;
- netdev_dbg(netdev, "%s Entry - rx_data: %d\n", __func__, rx_data);
- while (rx_data) {
- ks8842_rx_frame(netdev, adapter);
- rx_data = ks8842_read16(adapter, 16, REG_RXMIR) & 0x1fff;
- }
-}
-
-void ks8842_handle_tx(struct net_device *netdev, struct ks8842_adapter *adapter)
-{
- u16 sr = ks8842_read16(adapter, 16, REG_TXSR);
- netdev_dbg(netdev, "%s - entry, sr: %x\n", __func__, sr);
- netdev->stats.tx_packets++;
- if (netif_queue_stopped(netdev))
- netif_wake_queue(netdev);
-}
-
-void ks8842_handle_rx_overrun(struct net_device *netdev,
- struct ks8842_adapter *adapter)
-{
- netdev_dbg(netdev, "%s: entry\n", __func__);
- netdev->stats.rx_errors++;
- netdev->stats.rx_fifo_errors++;
-}
-
-void ks8842_tasklet(unsigned long arg)
-{
- struct net_device *netdev = (struct net_device *)arg;
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- u16 isr;
- unsigned long flags;
- u16 entry_bank;
-
- /* read current bank to be able to set it back */
- spin_lock_irqsave(&adapter->lock, flags);
- entry_bank = ioread16(adapter->hw_addr + REG_SELECT_BANK);
- spin_unlock_irqrestore(&adapter->lock, flags);
-
- isr = ks8842_read16(adapter, 18, REG_ISR);
- netdev_dbg(netdev, "%s - ISR: 0x%x\n", __func__, isr);
-
- /* when running in DMA mode, do not ack RX interrupts, it is handled
- internally by timberdale, otherwise it's DMA FIFO:s would stop
- */
- if (KS8842_USE_DMA(adapter))
- isr &= ~IRQ_RX;
-
- /* Ack */
- ks8842_write16(adapter, 18, isr, REG_ISR);
-
- if (!(adapter->conf_flags & MICREL_KS884X))
- /* Ack in the timberdale IP as well */
- iowrite32(0x1, adapter->hw_addr + REG_TIMB_IAR);
-
- if (!netif_running(netdev))
- return;
-
- if (isr & IRQ_LINK_CHANGE)
- ks8842_update_link_status(netdev, adapter);
-
- /* should not get IRQ_RX when running DMA mode */
- if (isr & (IRQ_RX | IRQ_RX_ERROR) && !KS8842_USE_DMA(adapter))
- ks8842_handle_rx(netdev, adapter);
-
- /* should only happen when in PIO mode */
- if (isr & IRQ_TX)
- ks8842_handle_tx(netdev, adapter);
-
- if (isr & IRQ_RX_OVERRUN)
- ks8842_handle_rx_overrun(netdev, adapter);
-
- if (isr & IRQ_TX_STOPPED) {
- ks8842_disable_tx(adapter);
- ks8842_enable_tx(adapter);
- }
-
- if (isr & IRQ_RX_STOPPED) {
- ks8842_disable_rx(adapter);
- ks8842_enable_rx(adapter);
- }
-
- /* re-enable interrupts, put back the bank selection register */
- spin_lock_irqsave(&adapter->lock, flags);
- if (KS8842_USE_DMA(adapter))
- ks8842_write16(adapter, 18, ENABLED_IRQS_DMA, REG_IER);
- else
- ks8842_write16(adapter, 18, ENABLED_IRQS, REG_IER);
- iowrite16(entry_bank, adapter->hw_addr + REG_SELECT_BANK);
-
- /* Make sure timberdale continues DMA operations, they are stopped while
- we are handling the ks8842 because we might change bank */
- if (KS8842_USE_DMA(adapter))
- ks8842_resume_dma(adapter);
-
- spin_unlock_irqrestore(&adapter->lock, flags);
-}
-
-static irqreturn_t ks8842_irq(int irq, void *devid)
-{
- struct net_device *netdev = devid;
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- u16 isr;
- u16 entry_bank = ioread16(adapter->hw_addr + REG_SELECT_BANK);
- irqreturn_t ret = IRQ_NONE;
-
- isr = ks8842_read16(adapter, 18, REG_ISR);
- netdev_dbg(netdev, "%s - ISR: 0x%x\n", __func__, isr);
-
- if (isr) {
- if (KS8842_USE_DMA(adapter))
- /* disable all but RX IRQ, since the FPGA relies on it*/
- ks8842_write16(adapter, 18, IRQ_RX, REG_IER);
- else
- /* disable IRQ */
- ks8842_write16(adapter, 18, 0x00, REG_IER);
-
- /* schedule tasklet */
- tasklet_schedule(&adapter->tasklet);
-
- ret = IRQ_HANDLED;
- }
-
- iowrite16(entry_bank, adapter->hw_addr + REG_SELECT_BANK);
-
- /* After an interrupt, tell timberdale to continue DMA operations.
- DMA is disabled while we are handling the ks8842 because we might
- change bank */
- ks8842_resume_dma(adapter);
-
- return ret;
-}
-
-static void ks8842_dma_rx_cb(void *data)
-{
- struct net_device *netdev = data;
- struct ks8842_adapter *adapter = netdev_priv(netdev);
-
- netdev_dbg(netdev, "RX DMA finished\n");
- /* schedule tasklet */
- if (adapter->dma_rx.adesc)
- tasklet_schedule(&adapter->dma_rx.tasklet);
-}
-
-static void ks8842_dma_tx_cb(void *data)
-{
- struct net_device *netdev = data;
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct ks8842_tx_dma_ctl *ctl = &adapter->dma_tx;
-
- netdev_dbg(netdev, "TX DMA finished\n");
-
- if (!ctl->adesc)
- return;
-
- netdev->stats.tx_packets++;
- ctl->adesc = NULL;
-
- if (netif_queue_stopped(netdev))
- netif_wake_queue(netdev);
-}
-
-static void ks8842_stop_dma(struct ks8842_adapter *adapter)
-{
- struct ks8842_tx_dma_ctl *tx_ctl = &adapter->dma_tx;
- struct ks8842_rx_dma_ctl *rx_ctl = &adapter->dma_rx;
-
- tx_ctl->adesc = NULL;
- if (tx_ctl->chan)
- tx_ctl->chan->device->device_control(tx_ctl->chan,
- DMA_TERMINATE_ALL, 0);
-
- rx_ctl->adesc = NULL;
- if (rx_ctl->chan)
- rx_ctl->chan->device->device_control(rx_ctl->chan,
- DMA_TERMINATE_ALL, 0);
-
- if (sg_dma_address(&rx_ctl->sg))
- dma_unmap_single(adapter->dev, sg_dma_address(&rx_ctl->sg),
- DMA_BUFFER_SIZE, DMA_FROM_DEVICE);
- sg_dma_address(&rx_ctl->sg) = 0;
-
- dev_kfree_skb(rx_ctl->skb);
- rx_ctl->skb = NULL;
-}
-
-static void ks8842_dealloc_dma_bufs(struct ks8842_adapter *adapter)
-{
- struct ks8842_tx_dma_ctl *tx_ctl = &adapter->dma_tx;
- struct ks8842_rx_dma_ctl *rx_ctl = &adapter->dma_rx;
-
- ks8842_stop_dma(adapter);
-
- if (tx_ctl->chan)
- dma_release_channel(tx_ctl->chan);
- tx_ctl->chan = NULL;
-
- if (rx_ctl->chan)
- dma_release_channel(rx_ctl->chan);
- rx_ctl->chan = NULL;
-
- tasklet_kill(&rx_ctl->tasklet);
-
- if (sg_dma_address(&tx_ctl->sg))
- dma_unmap_single(adapter->dev, sg_dma_address(&tx_ctl->sg),
- DMA_BUFFER_SIZE, DMA_TO_DEVICE);
- sg_dma_address(&tx_ctl->sg) = 0;
-
- kfree(tx_ctl->buf);
- tx_ctl->buf = NULL;
-}
-
-static bool ks8842_dma_filter_fn(struct dma_chan *chan, void *filter_param)
-{
- return chan->chan_id == (long)filter_param;
-}
-
-static int ks8842_alloc_dma_bufs(struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct ks8842_tx_dma_ctl *tx_ctl = &adapter->dma_tx;
- struct ks8842_rx_dma_ctl *rx_ctl = &adapter->dma_rx;
- int err;
-
- dma_cap_mask_t mask;
-
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- dma_cap_set(DMA_PRIVATE, mask);
-
- sg_init_table(&tx_ctl->sg, 1);
-
- tx_ctl->chan = dma_request_channel(mask, ks8842_dma_filter_fn,
- (void *)(long)tx_ctl->channel);
- if (!tx_ctl->chan) {
- err = -ENODEV;
- goto err;
- }
-
- /* allocate DMA buffer */
- tx_ctl->buf = kmalloc(DMA_BUFFER_SIZE, GFP_KERNEL);
- if (!tx_ctl->buf) {
- err = -ENOMEM;
- goto err;
- }
-
- sg_dma_address(&tx_ctl->sg) = dma_map_single(adapter->dev,
- tx_ctl->buf, DMA_BUFFER_SIZE, DMA_TO_DEVICE);
- err = dma_mapping_error(adapter->dev,
- sg_dma_address(&tx_ctl->sg));
- if (err) {
- sg_dma_address(&tx_ctl->sg) = 0;
- goto err;
- }
-
- rx_ctl->chan = dma_request_channel(mask, ks8842_dma_filter_fn,
- (void *)(long)rx_ctl->channel);
- if (!rx_ctl->chan) {
- err = -ENODEV;
- goto err;
- }
-
- tasklet_init(&rx_ctl->tasklet, ks8842_rx_frame_dma_tasklet,
- (unsigned long)netdev);
-
- return 0;
-err:
- ks8842_dealloc_dma_bufs(adapter);
- return err;
-}
-
-/* Netdevice operations */
-
-static int ks8842_open(struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- int err;
-
- netdev_dbg(netdev, "%s - entry\n", __func__);
-
- if (KS8842_USE_DMA(adapter)) {
- err = ks8842_alloc_dma_bufs(netdev);
-
- if (!err) {
- /* start RX dma */
- err = __ks8842_start_new_rx_dma(netdev);
- if (err)
- ks8842_dealloc_dma_bufs(adapter);
- }
-
- if (err) {
- printk(KERN_WARNING DRV_NAME
- ": Failed to initiate DMA, running PIO\n");
- ks8842_dealloc_dma_bufs(adapter);
- adapter->dma_rx.channel = -1;
- adapter->dma_tx.channel = -1;
- }
- }
-
- /* reset the HW */
- ks8842_reset_hw(adapter);
-
- ks8842_write_mac_addr(adapter, netdev->dev_addr);
-
- ks8842_update_link_status(netdev, adapter);
-
- err = request_irq(adapter->irq, ks8842_irq, IRQF_SHARED, DRV_NAME,
- netdev);
- if (err) {
- pr_err("Failed to request IRQ: %d: %d\n", adapter->irq, err);
- return err;
- }
-
- return 0;
-}
-
-static int ks8842_close(struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
-
- netdev_dbg(netdev, "%s - entry\n", __func__);
-
- cancel_work_sync(&adapter->timeout_work);
-
- if (KS8842_USE_DMA(adapter))
- ks8842_dealloc_dma_bufs(adapter);
-
- /* free the irq */
- free_irq(adapter->irq, netdev);
-
- /* disable the switch */
- ks8842_write16(adapter, 32, 0x0, REG_SW_ID_AND_ENABLE);
-
- return 0;
-}
-
-static netdev_tx_t ks8842_xmit_frame(struct sk_buff *skb,
- struct net_device *netdev)
-{
- int ret;
- struct ks8842_adapter *adapter = netdev_priv(netdev);
-
- netdev_dbg(netdev, "%s: entry\n", __func__);
-
- if (KS8842_USE_DMA(adapter)) {
- unsigned long flags;
- ret = ks8842_tx_frame_dma(skb, netdev);
- /* for now only allow one transfer at the time */
- spin_lock_irqsave(&adapter->lock, flags);
- if (adapter->dma_tx.adesc)
- netif_stop_queue(netdev);
- spin_unlock_irqrestore(&adapter->lock, flags);
- return ret;
- }
-
- ret = ks8842_tx_frame(skb, netdev);
-
- if (ks8842_tx_fifo_space(adapter) < netdev->mtu + 8)
- netif_stop_queue(netdev);
-
- return ret;
-}
-
-static int ks8842_set_mac(struct net_device *netdev, void *p)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct sockaddr *addr = p;
- char *mac = (u8 *)addr->sa_data;
-
- netdev_dbg(netdev, "%s: entry\n", __func__);
-
- if (!is_valid_ether_addr(addr->sa_data))
- return -EADDRNOTAVAIL;
-
- memcpy(netdev->dev_addr, mac, netdev->addr_len);
-
- ks8842_write_mac_addr(adapter, mac);
- return 0;
-}
-
-static void ks8842_tx_timeout_work(struct work_struct *work)
-{
- struct ks8842_adapter *adapter =
- container_of(work, struct ks8842_adapter, timeout_work);
- struct net_device *netdev = adapter->netdev;
- unsigned long flags;
-
- netdev_dbg(netdev, "%s: entry\n", __func__);
-
- spin_lock_irqsave(&adapter->lock, flags);
-
- if (KS8842_USE_DMA(adapter))
- ks8842_stop_dma(adapter);
-
- /* disable interrupts */
- ks8842_write16(adapter, 18, 0, REG_IER);
- ks8842_write16(adapter, 18, 0xFFFF, REG_ISR);
-
- netif_stop_queue(netdev);
-
- spin_unlock_irqrestore(&adapter->lock, flags);
-
- ks8842_reset_hw(adapter);
-
- ks8842_write_mac_addr(adapter, netdev->dev_addr);
-
- ks8842_update_link_status(netdev, adapter);
-
- if (KS8842_USE_DMA(adapter))
- __ks8842_start_new_rx_dma(netdev);
-}
-
-static void ks8842_tx_timeout(struct net_device *netdev)
-{
- struct ks8842_adapter *adapter = netdev_priv(netdev);
-
- netdev_dbg(netdev, "%s: entry\n", __func__);
-
- schedule_work(&adapter->timeout_work);
-}
-
-static const struct net_device_ops ks8842_netdev_ops = {
- .ndo_open = ks8842_open,
- .ndo_stop = ks8842_close,
- .ndo_start_xmit = ks8842_xmit_frame,
- .ndo_set_mac_address = ks8842_set_mac,
- .ndo_tx_timeout = ks8842_tx_timeout,
- .ndo_validate_addr = eth_validate_addr
-};
-
-static const struct ethtool_ops ks8842_ethtool_ops = {
- .get_link = ethtool_op_get_link,
-};
-
-static int __devinit ks8842_probe(struct platform_device *pdev)
-{
- int err = -ENOMEM;
- struct resource *iomem;
- struct net_device *netdev;
- struct ks8842_adapter *adapter;
- struct ks8842_platform_data *pdata = pdev->dev.platform_data;
- u16 id;
- unsigned i;
-
- iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!request_mem_region(iomem->start, resource_size(iomem), DRV_NAME))
- goto err_mem_region;
-
- netdev = alloc_etherdev(sizeof(struct ks8842_adapter));
- if (!netdev)
- goto err_alloc_etherdev;
-
- SET_NETDEV_DEV(netdev, &pdev->dev);
-
- adapter = netdev_priv(netdev);
- adapter->netdev = netdev;
- INIT_WORK(&adapter->timeout_work, ks8842_tx_timeout_work);
- adapter->hw_addr = ioremap(iomem->start, resource_size(iomem));
- adapter->conf_flags = iomem->flags;
-
- if (!adapter->hw_addr)
- goto err_ioremap;
-
- adapter->irq = platform_get_irq(pdev, 0);
- if (adapter->irq < 0) {
- err = adapter->irq;
- goto err_get_irq;
- }
-
- adapter->dev = (pdev->dev.parent) ? pdev->dev.parent : &pdev->dev;
-
- /* DMA is only supported when accessed via timberdale */
- if (!(adapter->conf_flags & MICREL_KS884X) && pdata &&
- (pdata->tx_dma_channel != -1) &&
- (pdata->rx_dma_channel != -1)) {
- adapter->dma_rx.channel = pdata->rx_dma_channel;
- adapter->dma_tx.channel = pdata->tx_dma_channel;
- } else {
- adapter->dma_rx.channel = -1;
- adapter->dma_tx.channel = -1;
- }
-
- tasklet_init(&adapter->tasklet, ks8842_tasklet, (unsigned long)netdev);
- spin_lock_init(&adapter->lock);
-
- netdev->netdev_ops = &ks8842_netdev_ops;
- netdev->ethtool_ops = &ks8842_ethtool_ops;
-
- /* Check if a mac address was given */
- i = netdev->addr_len;
- if (pdata) {
- for (i = 0; i < netdev->addr_len; i++)
- if (pdata->macaddr[i] != 0)
- break;
-
- if (i < netdev->addr_len)
- /* an address was passed, use it */
- memcpy(netdev->dev_addr, pdata->macaddr,
- netdev->addr_len);
- }
-
- if (i == netdev->addr_len) {
- ks8842_read_mac_addr(adapter, netdev->dev_addr);
-
- if (!is_valid_ether_addr(netdev->dev_addr))
- random_ether_addr(netdev->dev_addr);
- }
-
- id = ks8842_read16(adapter, 32, REG_SW_ID_AND_ENABLE);
-
- strcpy(netdev->name, "eth%d");
- err = register_netdev(netdev);
- if (err)
- goto err_register;
-
- platform_set_drvdata(pdev, netdev);
-
- pr_info("Found chip, family: 0x%x, id: 0x%x, rev: 0x%x\n",
- (id >> 8) & 0xff, (id >> 4) & 0xf, (id >> 1) & 0x7);
-
- return 0;
-
-err_register:
-err_get_irq:
- iounmap(adapter->hw_addr);
-err_ioremap:
- free_netdev(netdev);
-err_alloc_etherdev:
- release_mem_region(iomem->start, resource_size(iomem));
-err_mem_region:
- return err;
-}
-
-static int __devexit ks8842_remove(struct platform_device *pdev)
-{
- struct net_device *netdev = platform_get_drvdata(pdev);
- struct ks8842_adapter *adapter = netdev_priv(netdev);
- struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
- unregister_netdev(netdev);
- tasklet_kill(&adapter->tasklet);
- iounmap(adapter->hw_addr);
- free_netdev(netdev);
- release_mem_region(iomem->start, resource_size(iomem));
- platform_set_drvdata(pdev, NULL);
- return 0;
-}
-
-
-static struct platform_driver ks8842_platform_driver = {
- .driver = {
- .name = DRV_NAME,
- .owner = THIS_MODULE,
- },
- .probe = ks8842_probe,
- .remove = ks8842_remove,
-};
-
-static int __init ks8842_init(void)
-{
- return platform_driver_register(&ks8842_platform_driver);
-}
-
-static void __exit ks8842_exit(void)
-{
- platform_driver_unregister(&ks8842_platform_driver);
-}
-
-module_init(ks8842_init);
-module_exit(ks8842_exit);
-
-MODULE_DESCRIPTION("Timberdale KS8842 ethernet driver");
-MODULE_AUTHOR("Mocean Laboratories <info@mocean-labs.com>");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:ks8842");
-
+++ /dev/null
-/* drivers/net/ks8851.c
- *
- * Copyright 2009 Simtec Electronics
- * http://www.simtec.co.uk/
- * Ben Dooks <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#define DEBUG
-
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/ethtool.h>
-#include <linux/cache.h>
-#include <linux/crc32.h>
-#include <linux/mii.h>
-
-#include <linux/spi/spi.h>
-
-#include "ks8851.h"
-
-/**
- * struct ks8851_rxctrl - KS8851 driver rx control
- * @mchash: Multicast hash-table data.
- * @rxcr1: KS_RXCR1 register setting
- * @rxcr2: KS_RXCR2 register setting
- *
- * Representation of the settings needs to control the receive filtering
- * such as the multicast hash-filter and the receive register settings. This
- * is used to make the job of working out if the receive settings change and
- * then issuing the new settings to the worker that will send the necessary
- * commands.
- */
-struct ks8851_rxctrl {
- u16 mchash[4];
- u16 rxcr1;
- u16 rxcr2;
-};
-
-/**
- * union ks8851_tx_hdr - tx header data
- * @txb: The header as bytes
- * @txw: The header as 16bit, little-endian words
- *
- * A dual representation of the tx header data to allow
- * access to individual bytes, and to allow 16bit accesses
- * with 16bit alignment.
- */
-union ks8851_tx_hdr {
- u8 txb[6];
- __le16 txw[3];
-};
-
-/**
- * struct ks8851_net - KS8851 driver private data
- * @netdev: The network device we're bound to
- * @spidev: The spi device we're bound to.
- * @lock: Lock to ensure that the device is not accessed when busy.
- * @statelock: Lock on this structure for tx list.
- * @mii: The MII state information for the mii calls.
- * @rxctrl: RX settings for @rxctrl_work.
- * @tx_work: Work queue for tx packets
- * @irq_work: Work queue for servicing interrupts
- * @rxctrl_work: Work queue for updating RX mode and multicast lists
- * @txq: Queue of packets for transmission.
- * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1.
- * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2.
- * @txh: Space for generating packet TX header in DMA-able data
- * @rxd: Space for receiving SPI data, in DMA-able space.
- * @txd: Space for transmitting SPI data, in DMA-able space.
- * @msg_enable: The message flags controlling driver output (see ethtool).
- * @fid: Incrementing frame id tag.
- * @rc_ier: Cached copy of KS_IER.
- * @rc_ccr: Cached copy of KS_CCR.
- * @rc_rxqcr: Cached copy of KS_RXQCR.
- * @eeprom_size: Companion eeprom size in Bytes, 0 if no eeprom
- *
- * The @lock ensures that the chip is protected when certain operations are
- * in progress. When the read or write packet transfer is in progress, most
- * of the chip registers are not ccessible until the transfer is finished and
- * the DMA has been de-asserted.
- *
- * The @statelock is used to protect information in the structure which may
- * need to be accessed via several sources, such as the network driver layer
- * or one of the work queues.
- *
- * We align the buffers we may use for rx/tx to ensure that if the SPI driver
- * wants to DMA map them, it will not have any problems with data the driver
- * modifies.
- */
-struct ks8851_net {
- struct net_device *netdev;
- struct spi_device *spidev;
- struct mutex lock;
- spinlock_t statelock;
-
- union ks8851_tx_hdr txh ____cacheline_aligned;
- u8 rxd[8];
- u8 txd[8];
-
- u32 msg_enable ____cacheline_aligned;
- u16 tx_space;
- u8 fid;
-
- u16 rc_ier;
- u16 rc_rxqcr;
- u16 rc_ccr;
- u16 eeprom_size;
-
- struct mii_if_info mii;
- struct ks8851_rxctrl rxctrl;
-
- struct work_struct tx_work;
- struct work_struct irq_work;
- struct work_struct rxctrl_work;
-
- struct sk_buff_head txq;
-
- struct spi_message spi_msg1;
- struct spi_message spi_msg2;
- struct spi_transfer spi_xfer1;
- struct spi_transfer spi_xfer2[2];
-};
-
-static int msg_enable;
-
-/* shift for byte-enable data */
-#define BYTE_EN(_x) ((_x) << 2)
-
-/* turn register number and byte-enable mask into data for start of packet */
-#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg) << (8+2) | (_reg) >> 6)
-
-/* SPI register read/write calls.
- *
- * All these calls issue SPI transactions to access the chip's registers. They
- * all require that the necessary lock is held to prevent accesses when the
- * chip is busy transferring packet data (RX/TX FIFO accesses).
- */
-
-/**
- * ks8851_wrreg16 - write 16bit register value to chip
- * @ks: The chip state
- * @reg: The register address
- * @val: The value to write
- *
- * Issue a write to put the value @val into the register specified in @reg.
- */
-static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val)
-{
- struct spi_transfer *xfer = &ks->spi_xfer1;
- struct spi_message *msg = &ks->spi_msg1;
- __le16 txb[2];
- int ret;
-
- txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR);
- txb[1] = cpu_to_le16(val);
-
- xfer->tx_buf = txb;
- xfer->rx_buf = NULL;
- xfer->len = 4;
-
- ret = spi_sync(ks->spidev, msg);
- if (ret < 0)
- netdev_err(ks->netdev, "spi_sync() failed\n");
-}
-
-/**
- * ks8851_wrreg8 - write 8bit register value to chip
- * @ks: The chip state
- * @reg: The register address
- * @val: The value to write
- *
- * Issue a write to put the value @val into the register specified in @reg.
- */
-static void ks8851_wrreg8(struct ks8851_net *ks, unsigned reg, unsigned val)
-{
- struct spi_transfer *xfer = &ks->spi_xfer1;
- struct spi_message *msg = &ks->spi_msg1;
- __le16 txb[2];
- int ret;
- int bit;
-
- bit = 1 << (reg & 3);
-
- txb[0] = cpu_to_le16(MK_OP(bit, reg) | KS_SPIOP_WR);
- txb[1] = val;
-
- xfer->tx_buf = txb;
- xfer->rx_buf = NULL;
- xfer->len = 3;
-
- ret = spi_sync(ks->spidev, msg);
- if (ret < 0)
- netdev_err(ks->netdev, "spi_sync() failed\n");
-}
-
-/**
- * ks8851_rx_1msg - select whether to use one or two messages for spi read
- * @ks: The device structure
- *
- * Return whether to generate a single message with a tx and rx buffer
- * supplied to spi_sync(), or alternatively send the tx and rx buffers
- * as separate messages.
- *
- * Depending on the hardware in use, a single message may be more efficient
- * on interrupts or work done by the driver.
- *
- * This currently always returns true until we add some per-device data passed
- * from the platform code to specify which mode is better.
- */
-static inline bool ks8851_rx_1msg(struct ks8851_net *ks)
-{
- return true;
-}
-
-/**
- * ks8851_rdreg - issue read register command and return the data
- * @ks: The device state
- * @op: The register address and byte enables in message format.
- * @rxb: The RX buffer to return the result into
- * @rxl: The length of data expected.
- *
- * This is the low level read call that issues the necessary spi message(s)
- * to read data from the register specified in @op.
- */
-static void ks8851_rdreg(struct ks8851_net *ks, unsigned op,
- u8 *rxb, unsigned rxl)
-{
- struct spi_transfer *xfer;
- struct spi_message *msg;
- __le16 *txb = (__le16 *)ks->txd;
- u8 *trx = ks->rxd;
- int ret;
-
- txb[0] = cpu_to_le16(op | KS_SPIOP_RD);
-
- if (ks8851_rx_1msg(ks)) {
- msg = &ks->spi_msg1;
- xfer = &ks->spi_xfer1;
-
- xfer->tx_buf = txb;
- xfer->rx_buf = trx;
- xfer->len = rxl + 2;
- } else {
- msg = &ks->spi_msg2;
- xfer = ks->spi_xfer2;
-
- xfer->tx_buf = txb;
- xfer->rx_buf = NULL;
- xfer->len = 2;
-
- xfer++;
- xfer->tx_buf = NULL;
- xfer->rx_buf = trx;
- xfer->len = rxl;
- }
-
- ret = spi_sync(ks->spidev, msg);
- if (ret < 0)
- netdev_err(ks->netdev, "read: spi_sync() failed\n");
- else if (ks8851_rx_1msg(ks))
- memcpy(rxb, trx + 2, rxl);
- else
- memcpy(rxb, trx, rxl);
-}
-
-/**
- * ks8851_rdreg8 - read 8 bit register from device
- * @ks: The chip information
- * @reg: The register address
- *
- * Read a 8bit register from the chip, returning the result
-*/
-static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg)
-{
- u8 rxb[1];
-
- ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1);
- return rxb[0];
-}
-
-/**
- * ks8851_rdreg16 - read 16 bit register from device
- * @ks: The chip information
- * @reg: The register address
- *
- * Read a 16bit register from the chip, returning the result
-*/
-static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg)
-{
- __le16 rx = 0;
-
- ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2);
- return le16_to_cpu(rx);
-}
-
-/**
- * ks8851_rdreg32 - read 32 bit register from device
- * @ks: The chip information
- * @reg: The register address
- *
- * Read a 32bit register from the chip.
- *
- * Note, this read requires the address be aligned to 4 bytes.
-*/
-static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg)
-{
- __le32 rx = 0;
-
- WARN_ON(reg & 3);
-
- ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4);
- return le32_to_cpu(rx);
-}
-
-/**
- * ks8851_soft_reset - issue one of the soft reset to the device
- * @ks: The device state.
- * @op: The bit(s) to set in the GRR
- *
- * Issue the relevant soft-reset command to the device's GRR register
- * specified by @op.
- *
- * Note, the delays are in there as a caution to ensure that the reset
- * has time to take effect and then complete. Since the datasheet does
- * not currently specify the exact sequence, we have chosen something
- * that seems to work with our device.
- */
-static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op)
-{
- ks8851_wrreg16(ks, KS_GRR, op);
- mdelay(1); /* wait a short time to effect reset */
- ks8851_wrreg16(ks, KS_GRR, 0);
- mdelay(1); /* wait for condition to clear */
-}
-
-/**
- * ks8851_write_mac_addr - write mac address to device registers
- * @dev: The network device
- *
- * Update the KS8851 MAC address registers from the address in @dev.
- *
- * This call assumes that the chip is not running, so there is no need to
- * shutdown the RXQ process whilst setting this.
-*/
-static int ks8851_write_mac_addr(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int i;
-
- mutex_lock(&ks->lock);
-
- for (i = 0; i < ETH_ALEN; i++)
- ks8851_wrreg8(ks, KS_MAR(i), dev->dev_addr[i]);
-
- mutex_unlock(&ks->lock);
-
- return 0;
-}
-
-/**
- * ks8851_init_mac - initialise the mac address
- * @ks: The device structure
- *
- * Get or create the initial mac address for the device and then set that
- * into the station address register. Currently we assume that the device
- * does not have a valid mac address in it, and so we use random_ether_addr()
- * to create a new one.
- *
- * In future, the driver should check to see if the device has an EEPROM
- * attached and whether that has a valid ethernet address in it.
- */
-static void ks8851_init_mac(struct ks8851_net *ks)
-{
- struct net_device *dev = ks->netdev;
-
- random_ether_addr(dev->dev_addr);
- ks8851_write_mac_addr(dev);
-}
-
-/**
- * ks8851_irq - device interrupt handler
- * @irq: Interrupt number passed from the IRQ hnalder.
- * @pw: The private word passed to register_irq(), our struct ks8851_net.
- *
- * Disable the interrupt from happening again until we've processed the
- * current status by scheduling ks8851_irq_work().
- */
-static irqreturn_t ks8851_irq(int irq, void *pw)
-{
- struct ks8851_net *ks = pw;
-
- disable_irq_nosync(irq);
- schedule_work(&ks->irq_work);
- return IRQ_HANDLED;
-}
-
-/**
- * ks8851_rdfifo - read data from the receive fifo
- * @ks: The device state.
- * @buff: The buffer address
- * @len: The length of the data to read
- *
- * Issue an RXQ FIFO read command and read the @len amount of data from
- * the FIFO into the buffer specified by @buff.
- */
-static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len)
-{
- struct spi_transfer *xfer = ks->spi_xfer2;
- struct spi_message *msg = &ks->spi_msg2;
- u8 txb[1];
- int ret;
-
- netif_dbg(ks, rx_status, ks->netdev,
- "%s: %d@%p\n", __func__, len, buff);
-
- /* set the operation we're issuing */
- txb[0] = KS_SPIOP_RXFIFO;
-
- xfer->tx_buf = txb;
- xfer->rx_buf = NULL;
- xfer->len = 1;
-
- xfer++;
- xfer->rx_buf = buff;
- xfer->tx_buf = NULL;
- xfer->len = len;
-
- ret = spi_sync(ks->spidev, msg);
- if (ret < 0)
- netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__);
-}
-
-/**
- * ks8851_dbg_dumpkkt - dump initial packet contents to debug
- * @ks: The device state
- * @rxpkt: The data for the received packet
- *
- * Dump the initial data from the packet to dev_dbg().
-*/
-static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt)
-{
- netdev_dbg(ks->netdev,
- "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n",
- rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7],
- rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11],
- rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]);
-}
-
-/**
- * ks8851_rx_pkts - receive packets from the host
- * @ks: The device information.
- *
- * This is called from the IRQ work queue when the system detects that there
- * are packets in the receive queue. Find out how many packets there are and
- * read them from the FIFO.
- */
-static void ks8851_rx_pkts(struct ks8851_net *ks)
-{
- struct sk_buff *skb;
- unsigned rxfc;
- unsigned rxlen;
- unsigned rxstat;
- u32 rxh;
- u8 *rxpkt;
-
- rxfc = ks8851_rdreg8(ks, KS_RXFC);
-
- netif_dbg(ks, rx_status, ks->netdev,
- "%s: %d packets\n", __func__, rxfc);
-
- /* Currently we're issuing a read per packet, but we could possibly
- * improve the code by issuing a single read, getting the receive
- * header, allocating the packet and then reading the packet data
- * out in one go.
- *
- * This form of operation would require us to hold the SPI bus'
- * chipselect low during the entie transaction to avoid any
- * reset to the data stream coming from the chip.
- */
-
- for (; rxfc != 0; rxfc--) {
- rxh = ks8851_rdreg32(ks, KS_RXFHSR);
- rxstat = rxh & 0xffff;
- rxlen = rxh >> 16;
-
- netif_dbg(ks, rx_status, ks->netdev,
- "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen);
-
- /* the length of the packet includes the 32bit CRC */
-
- /* set dma read address */
- ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00);
-
- /* start the packet dma process, and set auto-dequeue rx */
- ks8851_wrreg16(ks, KS_RXQCR,
- ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE);
-
- if (rxlen > 4) {
- unsigned int rxalign;
-
- rxlen -= 4;
- rxalign = ALIGN(rxlen, 4);
- skb = netdev_alloc_skb_ip_align(ks->netdev, rxalign);
- if (skb) {
-
- /* 4 bytes of status header + 4 bytes of
- * garbage: we put them before ethernet
- * header, so that they are copied,
- * but ignored.
- */
-
- rxpkt = skb_put(skb, rxlen) - 8;
-
- ks8851_rdfifo(ks, rxpkt, rxalign + 8);
-
- if (netif_msg_pktdata(ks))
- ks8851_dbg_dumpkkt(ks, rxpkt);
-
- skb->protocol = eth_type_trans(skb, ks->netdev);
- netif_rx(skb);
-
- ks->netdev->stats.rx_packets++;
- ks->netdev->stats.rx_bytes += rxlen;
- }
- }
-
- ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
- }
-}
-
-/**
- * ks8851_irq_work - work queue handler for dealing with interrupt requests
- * @work: The work structure that was scheduled by schedule_work()
- *
- * This is the handler invoked when the ks8851_irq() is called to find out
- * what happened, as we cannot allow ourselves to sleep whilst waiting for
- * anything other process has the chip's lock.
- *
- * Read the interrupt status, work out what needs to be done and then clear
- * any of the interrupts that are not needed.
- */
-static void ks8851_irq_work(struct work_struct *work)
-{
- struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work);
- unsigned status;
- unsigned handled = 0;
-
- mutex_lock(&ks->lock);
-
- status = ks8851_rdreg16(ks, KS_ISR);
-
- netif_dbg(ks, intr, ks->netdev,
- "%s: status 0x%04x\n", __func__, status);
-
- if (status & IRQ_LCI) {
- /* should do something about checking link status */
- handled |= IRQ_LCI;
- }
-
- if (status & IRQ_LDI) {
- u16 pmecr = ks8851_rdreg16(ks, KS_PMECR);
- pmecr &= ~PMECR_WKEVT_MASK;
- ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);
-
- handled |= IRQ_LDI;
- }
-
- if (status & IRQ_RXPSI)
- handled |= IRQ_RXPSI;
-
- if (status & IRQ_TXI) {
- handled |= IRQ_TXI;
-
- /* no lock here, tx queue should have been stopped */
-
- /* update our idea of how much tx space is available to the
- * system */
- ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR);
-
- netif_dbg(ks, intr, ks->netdev,
- "%s: txspace %d\n", __func__, ks->tx_space);
- }
-
- if (status & IRQ_RXI)
- handled |= IRQ_RXI;
-
- if (status & IRQ_SPIBEI) {
- dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__);
- handled |= IRQ_SPIBEI;
- }
-
- ks8851_wrreg16(ks, KS_ISR, handled);
-
- if (status & IRQ_RXI) {
- /* the datasheet says to disable the rx interrupt during
- * packet read-out, however we're masking the interrupt
- * from the device so do not bother masking just the RX
- * from the device. */
-
- ks8851_rx_pkts(ks);
- }
-
- /* if something stopped the rx process, probably due to wanting
- * to change the rx settings, then do something about restarting
- * it. */
- if (status & IRQ_RXPSI) {
- struct ks8851_rxctrl *rxc = &ks->rxctrl;
-
- /* update the multicast hash table */
- ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]);
- ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]);
- ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]);
- ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]);
-
- ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2);
- ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1);
- }
-
- mutex_unlock(&ks->lock);
-
- if (status & IRQ_TXI)
- netif_wake_queue(ks->netdev);
-
- enable_irq(ks->netdev->irq);
-}
-
-/**
- * calc_txlen - calculate size of message to send packet
- * @len: Length of data
- *
- * Returns the size of the TXFIFO message needed to send
- * this packet.
- */
-static inline unsigned calc_txlen(unsigned len)
-{
- return ALIGN(len + 4, 4);
-}
-
-/**
- * ks8851_wrpkt - write packet to TX FIFO
- * @ks: The device state.
- * @txp: The sk_buff to transmit.
- * @irq: IRQ on completion of the packet.
- *
- * Send the @txp to the chip. This means creating the relevant packet header
- * specifying the length of the packet and the other information the chip
- * needs, such as IRQ on completion. Send the header and the packet data to
- * the device.
- */
-static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq)
-{
- struct spi_transfer *xfer = ks->spi_xfer2;
- struct spi_message *msg = &ks->spi_msg2;
- unsigned fid = 0;
- int ret;
-
- netif_dbg(ks, tx_queued, ks->netdev, "%s: skb %p, %d@%p, irq %d\n",
- __func__, txp, txp->len, txp->data, irq);
-
- fid = ks->fid++;
- fid &= TXFR_TXFID_MASK;
-
- if (irq)
- fid |= TXFR_TXIC; /* irq on completion */
-
- /* start header at txb[1] to align txw entries */
- ks->txh.txb[1] = KS_SPIOP_TXFIFO;
- ks->txh.txw[1] = cpu_to_le16(fid);
- ks->txh.txw[2] = cpu_to_le16(txp->len);
-
- xfer->tx_buf = &ks->txh.txb[1];
- xfer->rx_buf = NULL;
- xfer->len = 5;
-
- xfer++;
- xfer->tx_buf = txp->data;
- xfer->rx_buf = NULL;
- xfer->len = ALIGN(txp->len, 4);
-
- ret = spi_sync(ks->spidev, msg);
- if (ret < 0)
- netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__);
-}
-
-/**
- * ks8851_done_tx - update and then free skbuff after transmitting
- * @ks: The device state
- * @txb: The buffer transmitted
- */
-static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb)
-{
- struct net_device *dev = ks->netdev;
-
- dev->stats.tx_bytes += txb->len;
- dev->stats.tx_packets++;
-
- dev_kfree_skb(txb);
-}
-
-/**
- * ks8851_tx_work - process tx packet(s)
- * @work: The work strucutre what was scheduled.
- *
- * This is called when a number of packets have been scheduled for
- * transmission and need to be sent to the device.
- */
-static void ks8851_tx_work(struct work_struct *work)
-{
- struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work);
- struct sk_buff *txb;
- bool last = skb_queue_empty(&ks->txq);
-
- mutex_lock(&ks->lock);
-
- while (!last) {
- txb = skb_dequeue(&ks->txq);
- last = skb_queue_empty(&ks->txq);
-
- if (txb != NULL) {
- ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
- ks8851_wrpkt(ks, txb, last);
- ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
- ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
-
- ks8851_done_tx(ks, txb);
- }
- }
-
- mutex_unlock(&ks->lock);
-}
-
-/**
- * ks8851_set_powermode - set power mode of the device
- * @ks: The device state
- * @pwrmode: The power mode value to write to KS_PMECR.
- *
- * Change the power mode of the chip.
- */
-static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode)
-{
- unsigned pmecr;
-
- netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode);
-
- pmecr = ks8851_rdreg16(ks, KS_PMECR);
- pmecr &= ~PMECR_PM_MASK;
- pmecr |= pwrmode;
-
- ks8851_wrreg16(ks, KS_PMECR, pmecr);
-}
-
-/**
- * ks8851_net_open - open network device
- * @dev: The network device being opened.
- *
- * Called when the network device is marked active, such as a user executing
- * 'ifconfig up' on the device.
- */
-static int ks8851_net_open(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
-
- /* lock the card, even if we may not actually be doing anything
- * else at the moment */
- mutex_lock(&ks->lock);
-
- netif_dbg(ks, ifup, ks->netdev, "opening\n");
-
- /* bring chip out of any power saving mode it was in */
- ks8851_set_powermode(ks, PMECR_PM_NORMAL);
-
- /* issue a soft reset to the RX/TX QMU to put it into a known
- * state. */
- ks8851_soft_reset(ks, GRR_QMU);
-
- /* setup transmission parameters */
-
- ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */
- TXCR_TXPE | /* pad to min length */
- TXCR_TXCRC | /* add CRC */
- TXCR_TXFCE)); /* enable flow control */
-
- /* auto-increment tx data, reset tx pointer */
- ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);
-
- /* setup receiver control */
-
- ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */
- RXCR1_RXFCE | /* enable flow control */
- RXCR1_RXBE | /* broadcast enable */
- RXCR1_RXUE | /* unicast enable */
- RXCR1_RXE)); /* enable rx block */
-
- /* transfer entire frames out in one go */
- ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME);
-
- /* set receive counter timeouts */
- ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */
- ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */
- ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */
-
- ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */
- RXQCR_RXDBCTE | /* IRQ on byte count exceeded */
- RXQCR_RXDTTE); /* IRQ on time exceeded */
-
- ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
-
- /* clear then enable interrupts */
-
-#define STD_IRQ (IRQ_LCI | /* Link Change */ \
- IRQ_TXI | /* TX done */ \
- IRQ_RXI | /* RX done */ \
- IRQ_SPIBEI | /* SPI bus error */ \
- IRQ_TXPSI | /* TX process stop */ \
- IRQ_RXPSI) /* RX process stop */
-
- ks->rc_ier = STD_IRQ;
- ks8851_wrreg16(ks, KS_ISR, STD_IRQ);
- ks8851_wrreg16(ks, KS_IER, STD_IRQ);
-
- netif_start_queue(ks->netdev);
-
- netif_dbg(ks, ifup, ks->netdev, "network device up\n");
-
- mutex_unlock(&ks->lock);
- return 0;
-}
-
-/**
- * ks8851_net_stop - close network device
- * @dev: The device being closed.
- *
- * Called to close down a network device which has been active. Cancell any
- * work, shutdown the RX and TX process and then place the chip into a low
- * power state whilst it is not being used.
- */
-static int ks8851_net_stop(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
-
- netif_info(ks, ifdown, dev, "shutting down\n");
-
- netif_stop_queue(dev);
-
- mutex_lock(&ks->lock);
-
- /* stop any outstanding work */
- flush_work(&ks->irq_work);
- flush_work(&ks->tx_work);
- flush_work(&ks->rxctrl_work);
-
- /* turn off the IRQs and ack any outstanding */
- ks8851_wrreg16(ks, KS_IER, 0x0000);
- ks8851_wrreg16(ks, KS_ISR, 0xffff);
-
- /* shutdown RX process */
- ks8851_wrreg16(ks, KS_RXCR1, 0x0000);
-
- /* shutdown TX process */
- ks8851_wrreg16(ks, KS_TXCR, 0x0000);
-
- /* set powermode to soft power down to save power */
- ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN);
-
- /* ensure any queued tx buffers are dumped */
- while (!skb_queue_empty(&ks->txq)) {
- struct sk_buff *txb = skb_dequeue(&ks->txq);
-
- netif_dbg(ks, ifdown, ks->netdev,
- "%s: freeing txb %p\n", __func__, txb);
-
- dev_kfree_skb(txb);
- }
-
- mutex_unlock(&ks->lock);
- return 0;
-}
-
-/**
- * ks8851_start_xmit - transmit packet
- * @skb: The buffer to transmit
- * @dev: The device used to transmit the packet.
- *
- * Called by the network layer to transmit the @skb. Queue the packet for
- * the device and schedule the necessary work to transmit the packet when
- * it is free.
- *
- * We do this to firstly avoid sleeping with the network device locked,
- * and secondly so we can round up more than one packet to transmit which
- * means we can try and avoid generating too many transmit done interrupts.
- */
-static netdev_tx_t ks8851_start_xmit(struct sk_buff *skb,
- struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- unsigned needed = calc_txlen(skb->len);
- netdev_tx_t ret = NETDEV_TX_OK;
-
- netif_dbg(ks, tx_queued, ks->netdev,
- "%s: skb %p, %d@%p\n", __func__, skb, skb->len, skb->data);
-
- spin_lock(&ks->statelock);
-
- if (needed > ks->tx_space) {
- netif_stop_queue(dev);
- ret = NETDEV_TX_BUSY;
- } else {
- ks->tx_space -= needed;
- skb_queue_tail(&ks->txq, skb);
- }
-
- spin_unlock(&ks->statelock);
- schedule_work(&ks->tx_work);
-
- return ret;
-}
-
-/**
- * ks8851_rxctrl_work - work handler to change rx mode
- * @work: The work structure this belongs to.
- *
- * Lock the device and issue the necessary changes to the receive mode from
- * the network device layer. This is done so that we can do this without
- * having to sleep whilst holding the network device lock.
- *
- * Since the recommendation from Micrel is that the RXQ is shutdown whilst the
- * receive parameters are programmed, we issue a write to disable the RXQ and
- * then wait for the interrupt handler to be triggered once the RXQ shutdown is
- * complete. The interrupt handler then writes the new values into the chip.
- */
-static void ks8851_rxctrl_work(struct work_struct *work)
-{
- struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work);
-
- mutex_lock(&ks->lock);
-
- /* need to shutdown RXQ before modifying filter parameters */
- ks8851_wrreg16(ks, KS_RXCR1, 0x00);
-
- mutex_unlock(&ks->lock);
-}
-
-static void ks8851_set_rx_mode(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- struct ks8851_rxctrl rxctrl;
-
- memset(&rxctrl, 0, sizeof(rxctrl));
-
- if (dev->flags & IFF_PROMISC) {
- /* interface to receive everything */
-
- rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF;
- } else if (dev->flags & IFF_ALLMULTI) {
- /* accept all multicast packets */
-
- rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE |
- RXCR1_RXPAFMA | RXCR1_RXMAFMA);
- } else if (dev->flags & IFF_MULTICAST && !netdev_mc_empty(dev)) {
- struct netdev_hw_addr *ha;
- u32 crc;
-
- /* accept some multicast */
-
- netdev_for_each_mc_addr(ha, dev) {
- crc = ether_crc(ETH_ALEN, ha->addr);
- crc >>= (32 - 6); /* get top six bits */
-
- rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf));
- }
-
- rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXPAFMA;
- } else {
- /* just accept broadcast / unicast */
- rxctrl.rxcr1 = RXCR1_RXPAFMA;
- }
-
- rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */
- RXCR1_RXBE | /* broadcast enable */
- RXCR1_RXE | /* RX process enable */
- RXCR1_RXFCE); /* enable flow control */
-
- rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME;
-
- /* schedule work to do the actual set of the data if needed */
-
- spin_lock(&ks->statelock);
-
- if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) {
- memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl));
- schedule_work(&ks->rxctrl_work);
- }
-
- spin_unlock(&ks->statelock);
-}
-
-static int ks8851_set_mac_address(struct net_device *dev, void *addr)
-{
- struct sockaddr *sa = addr;
-
- if (netif_running(dev))
- return -EBUSY;
-
- if (!is_valid_ether_addr(sa->sa_data))
- return -EADDRNOTAVAIL;
-
- memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN);
- return ks8851_write_mac_addr(dev);
-}
-
-static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
-{
- struct ks8851_net *ks = netdev_priv(dev);
-
- if (!netif_running(dev))
- return -EINVAL;
-
- return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
-}
-
-static const struct net_device_ops ks8851_netdev_ops = {
- .ndo_open = ks8851_net_open,
- .ndo_stop = ks8851_net_stop,
- .ndo_do_ioctl = ks8851_net_ioctl,
- .ndo_start_xmit = ks8851_start_xmit,
- .ndo_set_mac_address = ks8851_set_mac_address,
- .ndo_set_rx_mode = ks8851_set_rx_mode,
- .ndo_change_mtu = eth_change_mtu,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-/* Companion eeprom access */
-
-enum { /* EEPROM programming states */
- EEPROM_CONTROL,
- EEPROM_ADDRESS,
- EEPROM_DATA,
- EEPROM_COMPLETE
-};
-
-/**
- * ks8851_eeprom_read - read a 16bits word in ks8851 companion EEPROM
- * @dev: The network device the PHY is on.
- * @addr: EEPROM address to read
- *
- * eeprom_size: used to define the data coding length. Can be changed
- * through debug-fs.
- *
- * Programs a read on the EEPROM using ks8851 EEPROM SW access feature.
- * Warning: The READ feature is not supported on ks8851 revision 0.
- *
- * Rough programming model:
- * - on period start: set clock high and read value on bus
- * - on period / 2: set clock low and program value on bus
- * - start on period / 2
- */
-unsigned int ks8851_eeprom_read(struct net_device *dev, unsigned int addr)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int eepcr;
- int ctrl = EEPROM_OP_READ;
- int state = EEPROM_CONTROL;
- int bit_count = EEPROM_OP_LEN - 1;
- unsigned int data = 0;
- int dummy;
- unsigned int addr_len;
-
- addr_len = (ks->eeprom_size == 128) ? 6 : 8;
-
- /* start transaction: chip select high, authorize write */
- mutex_lock(&ks->lock);
- eepcr = EEPCR_EESA | EEPCR_EESRWA;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr |= EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- while (state != EEPROM_COMPLETE) {
- /* falling clock period starts... */
- /* set EED_IO pin for control and address */
- eepcr &= ~EEPCR_EEDO;
- switch (state) {
- case EEPROM_CONTROL:
- eepcr |= ((ctrl >> bit_count) & 1) << 2;
- if (bit_count-- <= 0) {
- bit_count = addr_len - 1;
- state = EEPROM_ADDRESS;
- }
- break;
- case EEPROM_ADDRESS:
- eepcr |= ((addr >> bit_count) & 1) << 2;
- bit_count--;
- break;
- case EEPROM_DATA:
- /* Change to receive mode */
- eepcr &= ~EEPCR_EESRWA;
- break;
- }
-
- /* lower clock */
- eepcr &= ~EEPCR_EESCK;
-
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* waitread period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
-
- /* rising clock period starts... */
-
- /* raise clock */
- mutex_lock(&ks->lock);
- eepcr |= EEPCR_EESCK;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* Manage read */
- switch (state) {
- case EEPROM_ADDRESS:
- if (bit_count < 0) {
- bit_count = EEPROM_DATA_LEN - 1;
- state = EEPROM_DATA;
- }
- break;
- case EEPROM_DATA:
- mutex_lock(&ks->lock);
- dummy = ks8851_rdreg16(ks, KS_EEPCR);
- mutex_unlock(&ks->lock);
- data |= ((dummy >> EEPCR_EESB_OFFSET) & 1) << bit_count;
- if (bit_count-- <= 0)
- state = EEPROM_COMPLETE;
- break;
- }
-
- /* wait period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
- }
-
- /* close transaction */
- mutex_lock(&ks->lock);
- eepcr &= ~EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr = 0;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- return data;
-}
-
-/**
- * ks8851_eeprom_write - write a 16bits word in ks8851 companion EEPROM
- * @dev: The network device the PHY is on.
- * @op: operand (can be WRITE, EWEN, EWDS)
- * @addr: EEPROM address to write
- * @data: data to write
- *
- * eeprom_size: used to define the data coding length. Can be changed
- * through debug-fs.
- *
- * Programs a write on the EEPROM using ks8851 EEPROM SW access feature.
- *
- * Note that a write enable is required before writing data.
- *
- * Rough programming model:
- * - on period start: set clock high
- * - on period / 2: set clock low and program value on bus
- * - start on period / 2
- */
-void ks8851_eeprom_write(struct net_device *dev, unsigned int op,
- unsigned int addr, unsigned int data)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int eepcr;
- int state = EEPROM_CONTROL;
- int bit_count = EEPROM_OP_LEN - 1;
- unsigned int addr_len;
-
- addr_len = (ks->eeprom_size == 128) ? 6 : 8;
-
- switch (op) {
- case EEPROM_OP_EWEN:
- addr = 0x30;
- break;
- case EEPROM_OP_EWDS:
- addr = 0;
- break;
- }
-
- /* start transaction: chip select high, authorize write */
- mutex_lock(&ks->lock);
- eepcr = EEPCR_EESA | EEPCR_EESRWA;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr |= EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- while (state != EEPROM_COMPLETE) {
- /* falling clock period starts... */
- /* set EED_IO pin for control and address */
- eepcr &= ~EEPCR_EEDO;
- switch (state) {
- case EEPROM_CONTROL:
- eepcr |= ((op >> bit_count) & 1) << 2;
- if (bit_count-- <= 0) {
- bit_count = addr_len - 1;
- state = EEPROM_ADDRESS;
- }
- break;
- case EEPROM_ADDRESS:
- eepcr |= ((addr >> bit_count) & 1) << 2;
- if (bit_count-- <= 0) {
- if (op == EEPROM_OP_WRITE) {
- bit_count = EEPROM_DATA_LEN - 1;
- state = EEPROM_DATA;
- } else {
- state = EEPROM_COMPLETE;
- }
- }
- break;
- case EEPROM_DATA:
- eepcr |= ((data >> bit_count) & 1) << 2;
- if (bit_count-- <= 0)
- state = EEPROM_COMPLETE;
- break;
- }
-
- /* lower clock */
- eepcr &= ~EEPCR_EESCK;
-
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* wait period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
-
- /* rising clock period starts... */
-
- /* raise clock */
- eepcr |= EEPCR_EESCK;
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* wait period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
- }
-
- /* close transaction */
- mutex_lock(&ks->lock);
- eepcr &= ~EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr = 0;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
-}
-
-/* ethtool support */
-
-static void ks8851_get_drvinfo(struct net_device *dev,
- struct ethtool_drvinfo *di)
-{
- strlcpy(di->driver, "KS8851", sizeof(di->driver));
- strlcpy(di->version, "1.00", sizeof(di->version));
- strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info));
-}
-
-static u32 ks8851_get_msglevel(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return ks->msg_enable;
-}
-
-static void ks8851_set_msglevel(struct net_device *dev, u32 to)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- ks->msg_enable = to;
-}
-
-static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return mii_ethtool_gset(&ks->mii, cmd);
-}
-
-static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return mii_ethtool_sset(&ks->mii, cmd);
-}
-
-static u32 ks8851_get_link(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return mii_link_ok(&ks->mii);
-}
-
-static int ks8851_nway_reset(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return mii_nway_restart(&ks->mii);
-}
-
-static int ks8851_get_eeprom_len(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return ks->eeprom_size;
-}
-
-static int ks8851_get_eeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 *bytes)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- u16 *eeprom_buff;
- int first_word;
- int last_word;
- int ret_val = 0;
- u16 i;
-
- if (eeprom->len == 0)
- return -EINVAL;
-
- if (eeprom->len > ks->eeprom_size)
- return -EINVAL;
-
- eeprom->magic = ks8851_rdreg16(ks, KS_CIDER);
-
- first_word = eeprom->offset >> 1;
- last_word = (eeprom->offset + eeprom->len - 1) >> 1;
-
- eeprom_buff = kmalloc(sizeof(u16) *
- (last_word - first_word + 1), GFP_KERNEL);
- if (!eeprom_buff)
- return -ENOMEM;
-
- for (i = 0; i < last_word - first_word + 1; i++)
- eeprom_buff[i] = ks8851_eeprom_read(dev, first_word + 1);
-
- /* Device's eeprom is little-endian, word addressable */
- for (i = 0; i < last_word - first_word + 1; i++)
- le16_to_cpus(&eeprom_buff[i]);
-
- memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1), eeprom->len);
- kfree(eeprom_buff);
-
- return ret_val;
-}
-
-static int ks8851_set_eeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 *bytes)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- u16 *eeprom_buff;
- void *ptr;
- int max_len;
- int first_word;
- int last_word;
- int ret_val = 0;
- u16 i;
-
- if (eeprom->len == 0)
- return -EOPNOTSUPP;
-
- if (eeprom->len > ks->eeprom_size)
- return -EINVAL;
-
- if (eeprom->magic != ks8851_rdreg16(ks, KS_CIDER))
- return -EFAULT;
-
- first_word = eeprom->offset >> 1;
- last_word = (eeprom->offset + eeprom->len - 1) >> 1;
- max_len = (last_word - first_word + 1) * 2;
- eeprom_buff = kmalloc(max_len, GFP_KERNEL);
- if (!eeprom_buff)
- return -ENOMEM;
-
- ptr = (void *)eeprom_buff;
-
- if (eeprom->offset & 1) {
- /* need read/modify/write of first changed EEPROM word */
- /* only the second byte of the word is being modified */
- eeprom_buff[0] = ks8851_eeprom_read(dev, first_word);
- ptr++;
- }
- if ((eeprom->offset + eeprom->len) & 1)
- /* need read/modify/write of last changed EEPROM word */
- /* only the first byte of the word is being modified */
- eeprom_buff[last_word - first_word] =
- ks8851_eeprom_read(dev, last_word);
-
-
- /* Device's eeprom is little-endian, word addressable */
- le16_to_cpus(&eeprom_buff[0]);
- le16_to_cpus(&eeprom_buff[last_word - first_word]);
-
- memcpy(ptr, bytes, eeprom->len);
-
- for (i = 0; i < last_word - first_word + 1; i++)
- eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
-
- ks8851_eeprom_write(dev, EEPROM_OP_EWEN, 0, 0);
-
- for (i = 0; i < last_word - first_word + 1; i++) {
- ks8851_eeprom_write(dev, EEPROM_OP_WRITE, first_word + i,
- eeprom_buff[i]);
- mdelay(EEPROM_WRITE_TIME);
- }
-
- ks8851_eeprom_write(dev, EEPROM_OP_EWDS, 0, 0);
-
- kfree(eeprom_buff);
- return ret_val;
-}
-
-static const struct ethtool_ops ks8851_ethtool_ops = {
- .get_drvinfo = ks8851_get_drvinfo,
- .get_msglevel = ks8851_get_msglevel,
- .set_msglevel = ks8851_set_msglevel,
- .get_settings = ks8851_get_settings,
- .set_settings = ks8851_set_settings,
- .get_link = ks8851_get_link,
- .nway_reset = ks8851_nway_reset,
- .get_eeprom_len = ks8851_get_eeprom_len,
- .get_eeprom = ks8851_get_eeprom,
- .set_eeprom = ks8851_set_eeprom,
-};
-
-/* MII interface controls */
-
-/**
- * ks8851_phy_reg - convert MII register into a KS8851 register
- * @reg: MII register number.
- *
- * Return the KS8851 register number for the corresponding MII PHY register
- * if possible. Return zero if the MII register has no direct mapping to the
- * KS8851 register set.
- */
-static int ks8851_phy_reg(int reg)
-{
- switch (reg) {
- case MII_BMCR:
- return KS_P1MBCR;
- case MII_BMSR:
- return KS_P1MBSR;
- case MII_PHYSID1:
- return KS_PHY1ILR;
- case MII_PHYSID2:
- return KS_PHY1IHR;
- case MII_ADVERTISE:
- return KS_P1ANAR;
- case MII_LPA:
- return KS_P1ANLPR;
- }
-
- return 0x0;
-}
-
-/**
- * ks8851_phy_read - MII interface PHY register read.
- * @dev: The network device the PHY is on.
- * @phy_addr: Address of PHY (ignored as we only have one)
- * @reg: The register to read.
- *
- * This call reads data from the PHY register specified in @reg. Since the
- * device does not support all the MII registers, the non-existent values
- * are always returned as zero.
- *
- * We return zero for unsupported registers as the MII code does not check
- * the value returned for any error status, and simply returns it to the
- * caller. The mii-tool that the driver was tested with takes any -ve error
- * as real PHY capabilities, thus displaying incorrect data to the user.
- */
-static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int ksreg;
- int result;
-
- ksreg = ks8851_phy_reg(reg);
- if (!ksreg)
- return 0x0; /* no error return allowed, so use zero */
-
- mutex_lock(&ks->lock);
- result = ks8851_rdreg16(ks, ksreg);
- mutex_unlock(&ks->lock);
-
- return result;
-}
-
-static void ks8851_phy_write(struct net_device *dev,
- int phy, int reg, int value)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int ksreg;
-
- ksreg = ks8851_phy_reg(reg);
- if (ksreg) {
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, ksreg, value);
- mutex_unlock(&ks->lock);
- }
-}
-
-/**
- * ks8851_read_selftest - read the selftest memory info.
- * @ks: The device state
- *
- * Read and check the TX/RX memory selftest information.
- */
-static int ks8851_read_selftest(struct ks8851_net *ks)
-{
- unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
- int ret = 0;
- unsigned rd;
-
- rd = ks8851_rdreg16(ks, KS_MBIR);
-
- if ((rd & both_done) != both_done) {
- netdev_warn(ks->netdev, "Memory selftest not finished\n");
- return 0;
- }
-
- if (rd & MBIR_TXMBFA) {
- netdev_err(ks->netdev, "TX memory selftest fail\n");
- ret |= 1;
- }
-
- if (rd & MBIR_RXMBFA) {
- netdev_err(ks->netdev, "RX memory selftest fail\n");
- ret |= 2;
- }
-
- return 0;
-}
-
-/* driver bus management functions */
-
-#ifdef CONFIG_PM
-static int ks8851_suspend(struct spi_device *spi, pm_message_t state)
-{
- struct ks8851_net *ks = dev_get_drvdata(&spi->dev);
- struct net_device *dev = ks->netdev;
-
- if (netif_running(dev)) {
- netif_device_detach(dev);
- ks8851_net_stop(dev);
- }
-
- return 0;
-}
-
-static int ks8851_resume(struct spi_device *spi)
-{
- struct ks8851_net *ks = dev_get_drvdata(&spi->dev);
- struct net_device *dev = ks->netdev;
-
- if (netif_running(dev)) {
- ks8851_net_open(dev);
- netif_device_attach(dev);
- }
-
- return 0;
-}
-#else
-#define ks8851_suspend NULL
-#define ks8851_resume NULL
-#endif
-
-static int __devinit ks8851_probe(struct spi_device *spi)
-{
- struct net_device *ndev;
- struct ks8851_net *ks;
- int ret;
-
- ndev = alloc_etherdev(sizeof(struct ks8851_net));
- if (!ndev) {
- dev_err(&spi->dev, "failed to alloc ethernet device\n");
- return -ENOMEM;
- }
-
- spi->bits_per_word = 8;
-
- ks = netdev_priv(ndev);
-
- ks->netdev = ndev;
- ks->spidev = spi;
- ks->tx_space = 6144;
-
- mutex_init(&ks->lock);
- spin_lock_init(&ks->statelock);
-
- INIT_WORK(&ks->tx_work, ks8851_tx_work);
- INIT_WORK(&ks->irq_work, ks8851_irq_work);
- INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work);
-
- /* initialise pre-made spi transfer messages */
-
- spi_message_init(&ks->spi_msg1);
- spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1);
-
- spi_message_init(&ks->spi_msg2);
- spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2);
- spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2);
-
- /* setup mii state */
- ks->mii.dev = ndev;
- ks->mii.phy_id = 1,
- ks->mii.phy_id_mask = 1;
- ks->mii.reg_num_mask = 0xf;
- ks->mii.mdio_read = ks8851_phy_read;
- ks->mii.mdio_write = ks8851_phy_write;
-
- dev_info(&spi->dev, "message enable is %d\n", msg_enable);
-
- /* set the default message enable */
- ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
- NETIF_MSG_PROBE |
- NETIF_MSG_LINK));
-
- skb_queue_head_init(&ks->txq);
-
- SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops);
- SET_NETDEV_DEV(ndev, &spi->dev);
-
- dev_set_drvdata(&spi->dev, ks);
-
- ndev->if_port = IF_PORT_100BASET;
- ndev->netdev_ops = &ks8851_netdev_ops;
- ndev->irq = spi->irq;
-
- /* issue a global soft reset to reset the device. */
- ks8851_soft_reset(ks, GRR_GSR);
-
- /* simple check for a valid chip being connected to the bus */
-
- if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
- dev_err(&spi->dev, "failed to read device ID\n");
- ret = -ENODEV;
- goto err_id;
- }
-
- /* cache the contents of the CCR register for EEPROM, etc. */
- ks->rc_ccr = ks8851_rdreg16(ks, KS_CCR);
-
- if (ks->rc_ccr & CCR_EEPROM)
- ks->eeprom_size = 128;
- else
- ks->eeprom_size = 0;
-
- ks8851_read_selftest(ks);
- ks8851_init_mac(ks);
-
- ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW,
- ndev->name, ks);
- if (ret < 0) {
- dev_err(&spi->dev, "failed to get irq\n");
- goto err_irq;
- }
-
- ret = register_netdev(ndev);
- if (ret) {
- dev_err(&spi->dev, "failed to register network device\n");
- goto err_netdev;
- }
-
- netdev_info(ndev, "revision %d, MAC %pM, IRQ %d\n",
- CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)),
- ndev->dev_addr, ndev->irq);
-
- return 0;
-
-
-err_netdev:
- free_irq(ndev->irq, ndev);
-
-err_id:
-err_irq:
- free_netdev(ndev);
- return ret;
-}
-
-static int __devexit ks8851_remove(struct spi_device *spi)
-{
- struct ks8851_net *priv = dev_get_drvdata(&spi->dev);
-
- if (netif_msg_drv(priv))
- dev_info(&spi->dev, "remove\n");
-
- unregister_netdev(priv->netdev);
- free_irq(spi->irq, priv);
- free_netdev(priv->netdev);
-
- return 0;
-}
-
-static struct spi_driver ks8851_driver = {
- .driver = {
- .name = "ks8851",
- .owner = THIS_MODULE,
- },
- .probe = ks8851_probe,
- .remove = __devexit_p(ks8851_remove),
- .suspend = ks8851_suspend,
- .resume = ks8851_resume,
-};
-
-static int __init ks8851_init(void)
-{
- return spi_register_driver(&ks8851_driver);
-}
-
-static void __exit ks8851_exit(void)
-{
- spi_unregister_driver(&ks8851_driver);
-}
-
-module_init(ks8851_init);
-module_exit(ks8851_exit);
-
-MODULE_DESCRIPTION("KS8851 Network driver");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL");
-
-module_param_named(message, msg_enable, int, 0);
-MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
-MODULE_ALIAS("spi:ks8851");
+++ /dev/null
-/* drivers/net/ks8851.h
- *
- * Copyright 2009 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * KS8851 register definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#define KS_CCR 0x08
-#define CCR_EEPROM (1 << 9)
-#define CCR_SPI (1 << 8)
-#define CCR_32PIN (1 << 0)
-
-/* MAC address registers */
-#define KS_MAR(_m) 0x15 - (_m)
-#define KS_MARL 0x10
-#define KS_MARM 0x12
-#define KS_MARH 0x14
-
-#define KS_OBCR 0x20
-#define OBCR_ODS_16mA (1 << 6)
-
-#define KS_EEPCR 0x22
-#define EEPCR_EESRWA (1 << 5)
-#define EEPCR_EESA (1 << 4)
-#define EEPCR_EESB_OFFSET 3
-#define EEPCR_EESB (1 << EEPCR_EESB_OFFSET)
-#define EEPCR_EEDO (1 << 2)
-#define EEPCR_EESCK (1 << 1)
-#define EEPCR_EECS (1 << 0)
-
-#define EEPROM_OP_LEN 3 /* bits:*/
-#define EEPROM_OP_READ 0x06
-#define EEPROM_OP_EWEN 0x04
-#define EEPROM_OP_WRITE 0x05
-#define EEPROM_OP_EWDS 0x14
-
-#define EEPROM_DATA_LEN 16 /* 16 bits EEPROM */
-#define EEPROM_WRITE_TIME 4 /* wrt ack time in ms */
-#define EEPROM_SK_PERIOD 400 /* in us */
-
-#define KS_MBIR 0x24
-#define MBIR_TXMBF (1 << 12)
-#define MBIR_TXMBFA (1 << 11)
-#define MBIR_RXMBF (1 << 4)
-#define MBIR_RXMBFA (1 << 3)
-
-#define KS_GRR 0x26
-#define GRR_QMU (1 << 1)
-#define GRR_GSR (1 << 0)
-
-#define KS_WFCR 0x2A
-#define WFCR_MPRXE (1 << 7)
-#define WFCR_WF3E (1 << 3)
-#define WFCR_WF2E (1 << 2)
-#define WFCR_WF1E (1 << 1)
-#define WFCR_WF0E (1 << 0)
-
-#define KS_WF0CRC0 0x30
-#define KS_WF0CRC1 0x32
-#define KS_WF0BM0 0x34
-#define KS_WF0BM1 0x36
-#define KS_WF0BM2 0x38
-#define KS_WF0BM3 0x3A
-
-#define KS_WF1CRC0 0x40
-#define KS_WF1CRC1 0x42
-#define KS_WF1BM0 0x44
-#define KS_WF1BM1 0x46
-#define KS_WF1BM2 0x48
-#define KS_WF1BM3 0x4A
-
-#define KS_WF2CRC0 0x50
-#define KS_WF2CRC1 0x52
-#define KS_WF2BM0 0x54
-#define KS_WF2BM1 0x56
-#define KS_WF2BM2 0x58
-#define KS_WF2BM3 0x5A
-
-#define KS_WF3CRC0 0x60
-#define KS_WF3CRC1 0x62
-#define KS_WF3BM0 0x64
-#define KS_WF3BM1 0x66
-#define KS_WF3BM2 0x68
-#define KS_WF3BM3 0x6A
-
-#define KS_TXCR 0x70
-#define TXCR_TCGICMP (1 << 8)
-#define TXCR_TCGUDP (1 << 7)
-#define TXCR_TCGTCP (1 << 6)
-#define TXCR_TCGIP (1 << 5)
-#define TXCR_FTXQ (1 << 4)
-#define TXCR_TXFCE (1 << 3)
-#define TXCR_TXPE (1 << 2)
-#define TXCR_TXCRC (1 << 1)
-#define TXCR_TXE (1 << 0)
-
-#define KS_TXSR 0x72
-#define TXSR_TXLC (1 << 13)
-#define TXSR_TXMC (1 << 12)
-#define TXSR_TXFID_MASK (0x3f << 0)
-#define TXSR_TXFID_SHIFT (0)
-#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f)
-
-#define KS_RXCR1 0x74
-#define RXCR1_FRXQ (1 << 15)
-#define RXCR1_RXUDPFCC (1 << 14)
-#define RXCR1_RXTCPFCC (1 << 13)
-#define RXCR1_RXIPFCC (1 << 12)
-#define RXCR1_RXPAFMA (1 << 11)
-#define RXCR1_RXFCE (1 << 10)
-#define RXCR1_RXEFE (1 << 9)
-#define RXCR1_RXMAFMA (1 << 8)
-#define RXCR1_RXBE (1 << 7)
-#define RXCR1_RXME (1 << 6)
-#define RXCR1_RXUE (1 << 5)
-#define RXCR1_RXAE (1 << 4)
-#define RXCR1_RXINVF (1 << 1)
-#define RXCR1_RXE (1 << 0)
-
-#define KS_RXCR2 0x76
-#define RXCR2_SRDBL_MASK (0x7 << 5)
-#define RXCR2_SRDBL_SHIFT (5)
-#define RXCR2_SRDBL_4B (0x0 << 5)
-#define RXCR2_SRDBL_8B (0x1 << 5)
-#define RXCR2_SRDBL_16B (0x2 << 5)
-#define RXCR2_SRDBL_32B (0x3 << 5)
-#define RXCR2_SRDBL_FRAME (0x4 << 5)
-#define RXCR2_IUFFP (1 << 4)
-#define RXCR2_RXIUFCEZ (1 << 3)
-#define RXCR2_UDPLFE (1 << 2)
-#define RXCR2_RXICMPFCC (1 << 1)
-#define RXCR2_RXSAF (1 << 0)
-
-#define KS_TXMIR 0x78
-
-#define KS_RXFHSR 0x7C
-#define RXFSHR_RXFV (1 << 15)
-#define RXFSHR_RXICMPFCS (1 << 13)
-#define RXFSHR_RXIPFCS (1 << 12)
-#define RXFSHR_RXTCPFCS (1 << 11)
-#define RXFSHR_RXUDPFCS (1 << 10)
-#define RXFSHR_RXBF (1 << 7)
-#define RXFSHR_RXMF (1 << 6)
-#define RXFSHR_RXUF (1 << 5)
-#define RXFSHR_RXMR (1 << 4)
-#define RXFSHR_RXFT (1 << 3)
-#define RXFSHR_RXFTL (1 << 2)
-#define RXFSHR_RXRF (1 << 1)
-#define RXFSHR_RXCE (1 << 0)
-
-#define KS_RXFHBCR 0x7E
-#define KS_TXQCR 0x80
-#define TXQCR_AETFE (1 << 2)
-#define TXQCR_TXQMAM (1 << 1)
-#define TXQCR_METFE (1 << 0)
-
-#define KS_RXQCR 0x82
-#define RXQCR_RXDTTS (1 << 12)
-#define RXQCR_RXDBCTS (1 << 11)
-#define RXQCR_RXFCTS (1 << 10)
-#define RXQCR_RXIPHTOE (1 << 9)
-#define RXQCR_RXDTTE (1 << 7)
-#define RXQCR_RXDBCTE (1 << 6)
-#define RXQCR_RXFCTE (1 << 5)
-#define RXQCR_ADRFE (1 << 4)
-#define RXQCR_SDA (1 << 3)
-#define RXQCR_RRXEF (1 << 0)
-
-#define KS_TXFDPR 0x84
-#define TXFDPR_TXFPAI (1 << 14)
-#define TXFDPR_TXFP_MASK (0x7ff << 0)
-#define TXFDPR_TXFP_SHIFT (0)
-
-#define KS_RXFDPR 0x86
-#define RXFDPR_RXFPAI (1 << 14)
-
-#define KS_RXDTTR 0x8C
-#define KS_RXDBCTR 0x8E
-
-#define KS_IER 0x90
-#define KS_ISR 0x92
-#define IRQ_LCI (1 << 15)
-#define IRQ_TXI (1 << 14)
-#define IRQ_RXI (1 << 13)
-#define IRQ_RXOI (1 << 11)
-#define IRQ_TXPSI (1 << 9)
-#define IRQ_RXPSI (1 << 8)
-#define IRQ_TXSAI (1 << 6)
-#define IRQ_RXWFDI (1 << 5)
-#define IRQ_RXMPDI (1 << 4)
-#define IRQ_LDI (1 << 3)
-#define IRQ_EDI (1 << 2)
-#define IRQ_SPIBEI (1 << 1)
-#define IRQ_DEDI (1 << 0)
-
-#define KS_RXFCTR 0x9C
-#define KS_RXFC 0x9D
-#define RXFCTR_RXFC_MASK (0xff << 8)
-#define RXFCTR_RXFC_SHIFT (8)
-#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff)
-#define RXFCTR_RXFCT_MASK (0xff << 0)
-#define RXFCTR_RXFCT_SHIFT (0)
-
-#define KS_TXNTFSR 0x9E
-
-#define KS_MAHTR0 0xA0
-#define KS_MAHTR1 0xA2
-#define KS_MAHTR2 0xA4
-#define KS_MAHTR3 0xA6
-
-#define KS_FCLWR 0xB0
-#define KS_FCHWR 0xB2
-#define KS_FCOWR 0xB4
-
-#define KS_CIDER 0xC0
-#define CIDER_ID 0x8870
-#define CIDER_REV_MASK (0x7 << 1)
-#define CIDER_REV_SHIFT (1)
-#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7)
-
-#define KS_CGCR 0xC6
-
-#define KS_IACR 0xC8
-#define IACR_RDEN (1 << 12)
-#define IACR_TSEL_MASK (0x3 << 10)
-#define IACR_TSEL_SHIFT (10)
-#define IACR_TSEL_MIB (0x3 << 10)
-#define IACR_ADDR_MASK (0x1f << 0)
-#define IACR_ADDR_SHIFT (0)
-
-#define KS_IADLR 0xD0
-#define KS_IAHDR 0xD2
-
-#define KS_PMECR 0xD4
-#define PMECR_PME_DELAY (1 << 14)
-#define PMECR_PME_POL (1 << 12)
-#define PMECR_WOL_WAKEUP (1 << 11)
-#define PMECR_WOL_MAGICPKT (1 << 10)
-#define PMECR_WOL_LINKUP (1 << 9)
-#define PMECR_WOL_ENERGY (1 << 8)
-#define PMECR_AUTO_WAKE_EN (1 << 7)
-#define PMECR_WAKEUP_NORMAL (1 << 6)
-#define PMECR_WKEVT_MASK (0xf << 2)
-#define PMECR_WKEVT_SHIFT (2)
-#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf)
-#define PMECR_WKEVT_ENERGY (0x1 << 2)
-#define PMECR_WKEVT_LINK (0x2 << 2)
-#define PMECR_WKEVT_MAGICPKT (0x4 << 2)
-#define PMECR_WKEVT_FRAME (0x8 << 2)
-#define PMECR_PM_MASK (0x3 << 0)
-#define PMECR_PM_SHIFT (0)
-#define PMECR_PM_NORMAL (0x0 << 0)
-#define PMECR_PM_ENERGY (0x1 << 0)
-#define PMECR_PM_SOFTDOWN (0x2 << 0)
-#define PMECR_PM_POWERSAVE (0x3 << 0)
-
-/* Standard MII PHY data */
-#define KS_P1MBCR 0xE4
-#define KS_P1MBSR 0xE6
-#define KS_PHY1ILR 0xE8
-#define KS_PHY1IHR 0xEA
-#define KS_P1ANAR 0xEC
-#define KS_P1ANLPR 0xEE
-
-#define KS_P1SCLMD 0xF4
-#define P1SCLMD_LEDOFF (1 << 15)
-#define P1SCLMD_TXIDS (1 << 14)
-#define P1SCLMD_RESTARTAN (1 << 13)
-#define P1SCLMD_DISAUTOMDIX (1 << 10)
-#define P1SCLMD_FORCEMDIX (1 << 9)
-#define P1SCLMD_AUTONEGEN (1 << 7)
-#define P1SCLMD_FORCE100 (1 << 6)
-#define P1SCLMD_FORCEFDX (1 << 5)
-#define P1SCLMD_ADV_FLOW (1 << 4)
-#define P1SCLMD_ADV_100BT_FDX (1 << 3)
-#define P1SCLMD_ADV_100BT_HDX (1 << 2)
-#define P1SCLMD_ADV_10BT_FDX (1 << 1)
-#define P1SCLMD_ADV_10BT_HDX (1 << 0)
-
-#define KS_P1CR 0xF6
-#define P1CR_HP_MDIX (1 << 15)
-#define P1CR_REV_POL (1 << 13)
-#define P1CR_OP_100M (1 << 10)
-#define P1CR_OP_FDX (1 << 9)
-#define P1CR_OP_MDI (1 << 7)
-#define P1CR_AN_DONE (1 << 6)
-#define P1CR_LINK_GOOD (1 << 5)
-#define P1CR_PNTR_FLOW (1 << 4)
-#define P1CR_PNTR_100BT_FDX (1 << 3)
-#define P1CR_PNTR_100BT_HDX (1 << 2)
-#define P1CR_PNTR_10BT_FDX (1 << 1)
-#define P1CR_PNTR_10BT_HDX (1 << 0)
-
-/* TX Frame control */
-
-#define TXFR_TXIC (1 << 15)
-#define TXFR_TXFID_MASK (0x3f << 0)
-#define TXFR_TXFID_SHIFT (0)
-
-/* SPI frame opcodes */
-#define KS_SPIOP_RD (0x00)
-#define KS_SPIOP_WR (0x40)
-#define KS_SPIOP_RXFIFO (0x80)
-#define KS_SPIOP_TXFIFO (0xC0)
+++ /dev/null
-/**
- * drivers/net/ks8851_mll.c
- * Copyright (c) 2009 Micrel Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/**
- * Supports:
- * KS8851 16bit MLL chip from Micrel Inc.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/ethtool.h>
-#include <linux/cache.h>
-#include <linux/crc32.h>
-#include <linux/mii.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <asm/io.h>
-
-#define DRV_NAME "ks8851_mll"
-
-static u8 KS_DEFAULT_MAC_ADDRESS[] = { 0x00, 0x10, 0xA1, 0x86, 0x95, 0x11 };
-#define MAX_RECV_FRAMES 32
-#define MAX_BUF_SIZE 2048
-#define TX_BUF_SIZE 2000
-#define RX_BUF_SIZE 2000
-
-#define KS_CCR 0x08
-#define CCR_EEPROM (1 << 9)
-#define CCR_SPI (1 << 8)
-#define CCR_8BIT (1 << 7)
-#define CCR_16BIT (1 << 6)
-#define CCR_32BIT (1 << 5)
-#define CCR_SHARED (1 << 4)
-#define CCR_32PIN (1 << 0)
-
-/* MAC address registers */
-#define KS_MARL 0x10
-#define KS_MARM 0x12
-#define KS_MARH 0x14
-
-#define KS_OBCR 0x20
-#define OBCR_ODS_16MA (1 << 6)
-
-#define KS_EEPCR 0x22
-#define EEPCR_EESA (1 << 4)
-#define EEPCR_EESB (1 << 3)
-#define EEPCR_EEDO (1 << 2)
-#define EEPCR_EESCK (1 << 1)
-#define EEPCR_EECS (1 << 0)
-
-#define KS_MBIR 0x24
-#define MBIR_TXMBF (1 << 12)
-#define MBIR_TXMBFA (1 << 11)
-#define MBIR_RXMBF (1 << 4)
-#define MBIR_RXMBFA (1 << 3)
-
-#define KS_GRR 0x26
-#define GRR_QMU (1 << 1)
-#define GRR_GSR (1 << 0)
-
-#define KS_WFCR 0x2A
-#define WFCR_MPRXE (1 << 7)
-#define WFCR_WF3E (1 << 3)
-#define WFCR_WF2E (1 << 2)
-#define WFCR_WF1E (1 << 1)
-#define WFCR_WF0E (1 << 0)
-
-#define KS_WF0CRC0 0x30
-#define KS_WF0CRC1 0x32
-#define KS_WF0BM0 0x34
-#define KS_WF0BM1 0x36
-#define KS_WF0BM2 0x38
-#define KS_WF0BM3 0x3A
-
-#define KS_WF1CRC0 0x40
-#define KS_WF1CRC1 0x42
-#define KS_WF1BM0 0x44
-#define KS_WF1BM1 0x46
-#define KS_WF1BM2 0x48
-#define KS_WF1BM3 0x4A
-
-#define KS_WF2CRC0 0x50
-#define KS_WF2CRC1 0x52
-#define KS_WF2BM0 0x54
-#define KS_WF2BM1 0x56
-#define KS_WF2BM2 0x58
-#define KS_WF2BM3 0x5A
-
-#define KS_WF3CRC0 0x60
-#define KS_WF3CRC1 0x62
-#define KS_WF3BM0 0x64
-#define KS_WF3BM1 0x66
-#define KS_WF3BM2 0x68
-#define KS_WF3BM3 0x6A
-
-#define KS_TXCR 0x70
-#define TXCR_TCGICMP (1 << 8)
-#define TXCR_TCGUDP (1 << 7)
-#define TXCR_TCGTCP (1 << 6)
-#define TXCR_TCGIP (1 << 5)
-#define TXCR_FTXQ (1 << 4)
-#define TXCR_TXFCE (1 << 3)
-#define TXCR_TXPE (1 << 2)
-#define TXCR_TXCRC (1 << 1)
-#define TXCR_TXE (1 << 0)
-
-#define KS_TXSR 0x72
-#define TXSR_TXLC (1 << 13)
-#define TXSR_TXMC (1 << 12)
-#define TXSR_TXFID_MASK (0x3f << 0)
-#define TXSR_TXFID_SHIFT (0)
-#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f)
-
-
-#define KS_RXCR1 0x74
-#define RXCR1_FRXQ (1 << 15)
-#define RXCR1_RXUDPFCC (1 << 14)
-#define RXCR1_RXTCPFCC (1 << 13)
-#define RXCR1_RXIPFCC (1 << 12)
-#define RXCR1_RXPAFMA (1 << 11)
-#define RXCR1_RXFCE (1 << 10)
-#define RXCR1_RXEFE (1 << 9)
-#define RXCR1_RXMAFMA (1 << 8)
-#define RXCR1_RXBE (1 << 7)
-#define RXCR1_RXME (1 << 6)
-#define RXCR1_RXUE (1 << 5)
-#define RXCR1_RXAE (1 << 4)
-#define RXCR1_RXINVF (1 << 1)
-#define RXCR1_RXE (1 << 0)
-#define RXCR1_FILTER_MASK (RXCR1_RXINVF | RXCR1_RXAE | \
- RXCR1_RXMAFMA | RXCR1_RXPAFMA)
-
-#define KS_RXCR2 0x76
-#define RXCR2_SRDBL_MASK (0x7 << 5)
-#define RXCR2_SRDBL_SHIFT (5)
-#define RXCR2_SRDBL_4B (0x0 << 5)
-#define RXCR2_SRDBL_8B (0x1 << 5)
-#define RXCR2_SRDBL_16B (0x2 << 5)
-#define RXCR2_SRDBL_32B (0x3 << 5)
-/* #define RXCR2_SRDBL_FRAME (0x4 << 5) */
-#define RXCR2_IUFFP (1 << 4)
-#define RXCR2_RXIUFCEZ (1 << 3)
-#define RXCR2_UDPLFE (1 << 2)
-#define RXCR2_RXICMPFCC (1 << 1)
-#define RXCR2_RXSAF (1 << 0)
-
-#define KS_TXMIR 0x78
-
-#define KS_RXFHSR 0x7C
-#define RXFSHR_RXFV (1 << 15)
-#define RXFSHR_RXICMPFCS (1 << 13)
-#define RXFSHR_RXIPFCS (1 << 12)
-#define RXFSHR_RXTCPFCS (1 << 11)
-#define RXFSHR_RXUDPFCS (1 << 10)
-#define RXFSHR_RXBF (1 << 7)
-#define RXFSHR_RXMF (1 << 6)
-#define RXFSHR_RXUF (1 << 5)
-#define RXFSHR_RXMR (1 << 4)
-#define RXFSHR_RXFT (1 << 3)
-#define RXFSHR_RXFTL (1 << 2)
-#define RXFSHR_RXRF (1 << 1)
-#define RXFSHR_RXCE (1 << 0)
-#define RXFSHR_ERR (RXFSHR_RXCE | RXFSHR_RXRF |\
- RXFSHR_RXFTL | RXFSHR_RXMR |\
- RXFSHR_RXICMPFCS | RXFSHR_RXIPFCS |\
- RXFSHR_RXTCPFCS)
-#define KS_RXFHBCR 0x7E
-#define RXFHBCR_CNT_MASK 0x0FFF
-
-#define KS_TXQCR 0x80
-#define TXQCR_AETFE (1 << 2)
-#define TXQCR_TXQMAM (1 << 1)
-#define TXQCR_METFE (1 << 0)
-
-#define KS_RXQCR 0x82
-#define RXQCR_RXDTTS (1 << 12)
-#define RXQCR_RXDBCTS (1 << 11)
-#define RXQCR_RXFCTS (1 << 10)
-#define RXQCR_RXIPHTOE (1 << 9)
-#define RXQCR_RXDTTE (1 << 7)
-#define RXQCR_RXDBCTE (1 << 6)
-#define RXQCR_RXFCTE (1 << 5)
-#define RXQCR_ADRFE (1 << 4)
-#define RXQCR_SDA (1 << 3)
-#define RXQCR_RRXEF (1 << 0)
-#define RXQCR_CMD_CNTL (RXQCR_RXFCTE|RXQCR_ADRFE)
-
-#define KS_TXFDPR 0x84
-#define TXFDPR_TXFPAI (1 << 14)
-#define TXFDPR_TXFP_MASK (0x7ff << 0)
-#define TXFDPR_TXFP_SHIFT (0)
-
-#define KS_RXFDPR 0x86
-#define RXFDPR_RXFPAI (1 << 14)
-
-#define KS_RXDTTR 0x8C
-#define KS_RXDBCTR 0x8E
-
-#define KS_IER 0x90
-#define KS_ISR 0x92
-#define IRQ_LCI (1 << 15)
-#define IRQ_TXI (1 << 14)
-#define IRQ_RXI (1 << 13)
-#define IRQ_RXOI (1 << 11)
-#define IRQ_TXPSI (1 << 9)
-#define IRQ_RXPSI (1 << 8)
-#define IRQ_TXSAI (1 << 6)
-#define IRQ_RXWFDI (1 << 5)
-#define IRQ_RXMPDI (1 << 4)
-#define IRQ_LDI (1 << 3)
-#define IRQ_EDI (1 << 2)
-#define IRQ_SPIBEI (1 << 1)
-#define IRQ_DEDI (1 << 0)
-
-#define KS_RXFCTR 0x9C
-#define RXFCTR_THRESHOLD_MASK 0x00FF
-
-#define KS_RXFC 0x9D
-#define RXFCTR_RXFC_MASK (0xff << 8)
-#define RXFCTR_RXFC_SHIFT (8)
-#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff)
-#define RXFCTR_RXFCT_MASK (0xff << 0)
-#define RXFCTR_RXFCT_SHIFT (0)
-
-#define KS_TXNTFSR 0x9E
-
-#define KS_MAHTR0 0xA0
-#define KS_MAHTR1 0xA2
-#define KS_MAHTR2 0xA4
-#define KS_MAHTR3 0xA6
-
-#define KS_FCLWR 0xB0
-#define KS_FCHWR 0xB2
-#define KS_FCOWR 0xB4
-
-#define KS_CIDER 0xC0
-#define CIDER_ID 0x8870
-#define CIDER_REV_MASK (0x7 << 1)
-#define CIDER_REV_SHIFT (1)
-#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7)
-
-#define KS_CGCR 0xC6
-#define KS_IACR 0xC8
-#define IACR_RDEN (1 << 12)
-#define IACR_TSEL_MASK (0x3 << 10)
-#define IACR_TSEL_SHIFT (10)
-#define IACR_TSEL_MIB (0x3 << 10)
-#define IACR_ADDR_MASK (0x1f << 0)
-#define IACR_ADDR_SHIFT (0)
-
-#define KS_IADLR 0xD0
-#define KS_IAHDR 0xD2
-
-#define KS_PMECR 0xD4
-#define PMECR_PME_DELAY (1 << 14)
-#define PMECR_PME_POL (1 << 12)
-#define PMECR_WOL_WAKEUP (1 << 11)
-#define PMECR_WOL_MAGICPKT (1 << 10)
-#define PMECR_WOL_LINKUP (1 << 9)
-#define PMECR_WOL_ENERGY (1 << 8)
-#define PMECR_AUTO_WAKE_EN (1 << 7)
-#define PMECR_WAKEUP_NORMAL (1 << 6)
-#define PMECR_WKEVT_MASK (0xf << 2)
-#define PMECR_WKEVT_SHIFT (2)
-#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf)
-#define PMECR_WKEVT_ENERGY (0x1 << 2)
-#define PMECR_WKEVT_LINK (0x2 << 2)
-#define PMECR_WKEVT_MAGICPKT (0x4 << 2)
-#define PMECR_WKEVT_FRAME (0x8 << 2)
-#define PMECR_PM_MASK (0x3 << 0)
-#define PMECR_PM_SHIFT (0)
-#define PMECR_PM_NORMAL (0x0 << 0)
-#define PMECR_PM_ENERGY (0x1 << 0)
-#define PMECR_PM_SOFTDOWN (0x2 << 0)
-#define PMECR_PM_POWERSAVE (0x3 << 0)
-
-/* Standard MII PHY data */
-#define KS_P1MBCR 0xE4
-#define P1MBCR_FORCE_FDX (1 << 8)
-
-#define KS_P1MBSR 0xE6
-#define P1MBSR_AN_COMPLETE (1 << 5)
-#define P1MBSR_AN_CAPABLE (1 << 3)
-#define P1MBSR_LINK_UP (1 << 2)
-
-#define KS_PHY1ILR 0xE8
-#define KS_PHY1IHR 0xEA
-#define KS_P1ANAR 0xEC
-#define KS_P1ANLPR 0xEE
-
-#define KS_P1SCLMD 0xF4
-#define P1SCLMD_LEDOFF (1 << 15)
-#define P1SCLMD_TXIDS (1 << 14)
-#define P1SCLMD_RESTARTAN (1 << 13)
-#define P1SCLMD_DISAUTOMDIX (1 << 10)
-#define P1SCLMD_FORCEMDIX (1 << 9)
-#define P1SCLMD_AUTONEGEN (1 << 7)
-#define P1SCLMD_FORCE100 (1 << 6)
-#define P1SCLMD_FORCEFDX (1 << 5)
-#define P1SCLMD_ADV_FLOW (1 << 4)
-#define P1SCLMD_ADV_100BT_FDX (1 << 3)
-#define P1SCLMD_ADV_100BT_HDX (1 << 2)
-#define P1SCLMD_ADV_10BT_FDX (1 << 1)
-#define P1SCLMD_ADV_10BT_HDX (1 << 0)
-
-#define KS_P1CR 0xF6
-#define P1CR_HP_MDIX (1 << 15)
-#define P1CR_REV_POL (1 << 13)
-#define P1CR_OP_100M (1 << 10)
-#define P1CR_OP_FDX (1 << 9)
-#define P1CR_OP_MDI (1 << 7)
-#define P1CR_AN_DONE (1 << 6)
-#define P1CR_LINK_GOOD (1 << 5)
-#define P1CR_PNTR_FLOW (1 << 4)
-#define P1CR_PNTR_100BT_FDX (1 << 3)
-#define P1CR_PNTR_100BT_HDX (1 << 2)
-#define P1CR_PNTR_10BT_FDX (1 << 1)
-#define P1CR_PNTR_10BT_HDX (1 << 0)
-
-/* TX Frame control */
-
-#define TXFR_TXIC (1 << 15)
-#define TXFR_TXFID_MASK (0x3f << 0)
-#define TXFR_TXFID_SHIFT (0)
-
-#define KS_P1SR 0xF8
-#define P1SR_HP_MDIX (1 << 15)
-#define P1SR_REV_POL (1 << 13)
-#define P1SR_OP_100M (1 << 10)
-#define P1SR_OP_FDX (1 << 9)
-#define P1SR_OP_MDI (1 << 7)
-#define P1SR_AN_DONE (1 << 6)
-#define P1SR_LINK_GOOD (1 << 5)
-#define P1SR_PNTR_FLOW (1 << 4)
-#define P1SR_PNTR_100BT_FDX (1 << 3)
-#define P1SR_PNTR_100BT_HDX (1 << 2)
-#define P1SR_PNTR_10BT_FDX (1 << 1)
-#define P1SR_PNTR_10BT_HDX (1 << 0)
-
-#define ENUM_BUS_NONE 0
-#define ENUM_BUS_8BIT 1
-#define ENUM_BUS_16BIT 2
-#define ENUM_BUS_32BIT 3
-
-#define MAX_MCAST_LST 32
-#define HW_MCAST_SIZE 8
-
-/**
- * union ks_tx_hdr - tx header data
- * @txb: The header as bytes
- * @txw: The header as 16bit, little-endian words
- *
- * A dual representation of the tx header data to allow
- * access to individual bytes, and to allow 16bit accesses
- * with 16bit alignment.
- */
-union ks_tx_hdr {
- u8 txb[4];
- __le16 txw[2];
-};
-
-/**
- * struct ks_net - KS8851 driver private data
- * @net_device : The network device we're bound to
- * @hw_addr : start address of data register.
- * @hw_addr_cmd : start address of command register.
- * @txh : temporaly buffer to save status/length.
- * @lock : Lock to ensure that the device is not accessed when busy.
- * @pdev : Pointer to platform device.
- * @mii : The MII state information for the mii calls.
- * @frame_head_info : frame header information for multi-pkt rx.
- * @statelock : Lock on this structure for tx list.
- * @msg_enable : The message flags controlling driver output (see ethtool).
- * @frame_cnt : number of frames received.
- * @bus_width : i/o bus width.
- * @irq : irq number assigned to this device.
- * @rc_rxqcr : Cached copy of KS_RXQCR.
- * @rc_txcr : Cached copy of KS_TXCR.
- * @rc_ier : Cached copy of KS_IER.
- * @sharedbus : Multipex(addr and data bus) mode indicator.
- * @cmd_reg_cache : command register cached.
- * @cmd_reg_cache_int : command register cached. Used in the irq handler.
- * @promiscuous : promiscuous mode indicator.
- * @all_mcast : mutlicast indicator.
- * @mcast_lst_size : size of multicast list.
- * @mcast_lst : multicast list.
- * @mcast_bits : multicast enabed.
- * @mac_addr : MAC address assigned to this device.
- * @fid : frame id.
- * @extra_byte : number of extra byte prepended rx pkt.
- * @enabled : indicator this device works.
- *
- * The @lock ensures that the chip is protected when certain operations are
- * in progress. When the read or write packet transfer is in progress, most
- * of the chip registers are not accessible until the transfer is finished and
- * the DMA has been de-asserted.
- *
- * The @statelock is used to protect information in the structure which may
- * need to be accessed via several sources, such as the network driver layer
- * or one of the work queues.
- *
- */
-
-/* Receive multiplex framer header info */
-struct type_frame_head {
- u16 sts; /* Frame status */
- u16 len; /* Byte count */
-};
-
-struct ks_net {
- struct net_device *netdev;
- void __iomem *hw_addr;
- void __iomem *hw_addr_cmd;
- union ks_tx_hdr txh ____cacheline_aligned;
- struct mutex lock; /* spinlock to be interrupt safe */
- struct platform_device *pdev;
- struct mii_if_info mii;
- struct type_frame_head *frame_head_info;
- spinlock_t statelock;
- u32 msg_enable;
- u32 frame_cnt;
- int bus_width;
- int irq;
-
- u16 rc_rxqcr;
- u16 rc_txcr;
- u16 rc_ier;
- u16 sharedbus;
- u16 cmd_reg_cache;
- u16 cmd_reg_cache_int;
- u16 promiscuous;
- u16 all_mcast;
- u16 mcast_lst_size;
- u8 mcast_lst[MAX_MCAST_LST][ETH_ALEN];
- u8 mcast_bits[HW_MCAST_SIZE];
- u8 mac_addr[6];
- u8 fid;
- u8 extra_byte;
- u8 enabled;
-};
-
-static int msg_enable;
-
-#define BE3 0x8000 /* Byte Enable 3 */
-#define BE2 0x4000 /* Byte Enable 2 */
-#define BE1 0x2000 /* Byte Enable 1 */
-#define BE0 0x1000 /* Byte Enable 0 */
-
-/**
- * register read/write calls.
- *
- * All these calls issue transactions to access the chip's registers. They
- * all require that the necessary lock is held to prevent accesses when the
- * chip is busy transferring packet data (RX/TX FIFO accesses).
- */
-
-/**
- * ks_rdreg8 - read 8 bit register from device
- * @ks : The chip information
- * @offset: The register address
- *
- * Read a 8bit register from the chip, returning the result
- */
-static u8 ks_rdreg8(struct ks_net *ks, int offset)
-{
- u16 data;
- u8 shift_bit = offset & 0x03;
- u8 shift_data = (offset & 1) << 3;
- ks->cmd_reg_cache = (u16) offset | (u16)(BE0 << shift_bit);
- iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
- data = ioread16(ks->hw_addr);
- return (u8)(data >> shift_data);
-}
-
-/**
- * ks_rdreg16 - read 16 bit register from device
- * @ks : The chip information
- * @offset: The register address
- *
- * Read a 16bit register from the chip, returning the result
- */
-
-static u16 ks_rdreg16(struct ks_net *ks, int offset)
-{
- ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
- iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
- return ioread16(ks->hw_addr);
-}
-
-/**
- * ks_wrreg8 - write 8bit register value to chip
- * @ks: The chip information
- * @offset: The register address
- * @value: The value to write
- *
- */
-static void ks_wrreg8(struct ks_net *ks, int offset, u8 value)
-{
- u8 shift_bit = (offset & 0x03);
- u16 value_write = (u16)(value << ((offset & 1) << 3));
- ks->cmd_reg_cache = (u16)offset | (BE0 << shift_bit);
- iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
- iowrite16(value_write, ks->hw_addr);
-}
-
-/**
- * ks_wrreg16 - write 16bit register value to chip
- * @ks: The chip information
- * @offset: The register address
- * @value: The value to write
- *
- */
-
-static void ks_wrreg16(struct ks_net *ks, int offset, u16 value)
-{
- ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
- iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
- iowrite16(value, ks->hw_addr);
-}
-
-/**
- * ks_inblk - read a block of data from QMU. This is called after sudo DMA mode enabled.
- * @ks: The chip state
- * @wptr: buffer address to save data
- * @len: length in byte to read
- *
- */
-static inline void ks_inblk(struct ks_net *ks, u16 *wptr, u32 len)
-{
- len >>= 1;
- while (len--)
- *wptr++ = (u16)ioread16(ks->hw_addr);
-}
-
-/**
- * ks_outblk - write data to QMU. This is called after sudo DMA mode enabled.
- * @ks: The chip information
- * @wptr: buffer address
- * @len: length in byte to write
- *
- */
-static inline void ks_outblk(struct ks_net *ks, u16 *wptr, u32 len)
-{
- len >>= 1;
- while (len--)
- iowrite16(*wptr++, ks->hw_addr);
-}
-
-static void ks_disable_int(struct ks_net *ks)
-{
- ks_wrreg16(ks, KS_IER, 0x0000);
-} /* ks_disable_int */
-
-static void ks_enable_int(struct ks_net *ks)
-{
- ks_wrreg16(ks, KS_IER, ks->rc_ier);
-} /* ks_enable_int */
-
-/**
- * ks_tx_fifo_space - return the available hardware buffer size.
- * @ks: The chip information
- *
- */
-static inline u16 ks_tx_fifo_space(struct ks_net *ks)
-{
- return ks_rdreg16(ks, KS_TXMIR) & 0x1fff;
-}
-
-/**
- * ks_save_cmd_reg - save the command register from the cache.
- * @ks: The chip information
- *
- */
-static inline void ks_save_cmd_reg(struct ks_net *ks)
-{
- /*ks8851 MLL has a bug to read back the command register.
- * So rely on software to save the content of command register.
- */
- ks->cmd_reg_cache_int = ks->cmd_reg_cache;
-}
-
-/**
- * ks_restore_cmd_reg - restore the command register from the cache and
- * write to hardware register.
- * @ks: The chip information
- *
- */
-static inline void ks_restore_cmd_reg(struct ks_net *ks)
-{
- ks->cmd_reg_cache = ks->cmd_reg_cache_int;
- iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
-}
-
-/**
- * ks_set_powermode - set power mode of the device
- * @ks: The chip information
- * @pwrmode: The power mode value to write to KS_PMECR.
- *
- * Change the power mode of the chip.
- */
-static void ks_set_powermode(struct ks_net *ks, unsigned pwrmode)
-{
- unsigned pmecr;
-
- netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode);
-
- ks_rdreg16(ks, KS_GRR);
- pmecr = ks_rdreg16(ks, KS_PMECR);
- pmecr &= ~PMECR_PM_MASK;
- pmecr |= pwrmode;
-
- ks_wrreg16(ks, KS_PMECR, pmecr);
-}
-
-/**
- * ks_read_config - read chip configuration of bus width.
- * @ks: The chip information
- *
- */
-static void ks_read_config(struct ks_net *ks)
-{
- u16 reg_data = 0;
-
- /* Regardless of bus width, 8 bit read should always work.*/
- reg_data = ks_rdreg8(ks, KS_CCR) & 0x00FF;
- reg_data |= ks_rdreg8(ks, KS_CCR+1) << 8;
-
- /* addr/data bus are multiplexed */
- ks->sharedbus = (reg_data & CCR_SHARED) == CCR_SHARED;
-
- /* There are garbage data when reading data from QMU,
- depending on bus-width.
- */
-
- if (reg_data & CCR_8BIT) {
- ks->bus_width = ENUM_BUS_8BIT;
- ks->extra_byte = 1;
- } else if (reg_data & CCR_16BIT) {
- ks->bus_width = ENUM_BUS_16BIT;
- ks->extra_byte = 2;
- } else {
- ks->bus_width = ENUM_BUS_32BIT;
- ks->extra_byte = 4;
- }
-}
-
-/**
- * ks_soft_reset - issue one of the soft reset to the device
- * @ks: The device state.
- * @op: The bit(s) to set in the GRR
- *
- * Issue the relevant soft-reset command to the device's GRR register
- * specified by @op.
- *
- * Note, the delays are in there as a caution to ensure that the reset
- * has time to take effect and then complete. Since the datasheet does
- * not currently specify the exact sequence, we have chosen something
- * that seems to work with our device.
- */
-static void ks_soft_reset(struct ks_net *ks, unsigned op)
-{
- /* Disable interrupt first */
- ks_wrreg16(ks, KS_IER, 0x0000);
- ks_wrreg16(ks, KS_GRR, op);
- mdelay(10); /* wait a short time to effect reset */
- ks_wrreg16(ks, KS_GRR, 0);
- mdelay(1); /* wait for condition to clear */
-}
-
-
-void ks_enable_qmu(struct ks_net *ks)
-{
- u16 w;
-
- w = ks_rdreg16(ks, KS_TXCR);
- /* Enables QMU Transmit (TXCR). */
- ks_wrreg16(ks, KS_TXCR, w | TXCR_TXE);
-
- /*
- * RX Frame Count Threshold Enable and Auto-Dequeue RXQ Frame
- * Enable
- */
-
- w = ks_rdreg16(ks, KS_RXQCR);
- ks_wrreg16(ks, KS_RXQCR, w | RXQCR_RXFCTE);
-
- /* Enables QMU Receive (RXCR1). */
- w = ks_rdreg16(ks, KS_RXCR1);
- ks_wrreg16(ks, KS_RXCR1, w | RXCR1_RXE);
- ks->enabled = true;
-} /* ks_enable_qmu */
-
-static void ks_disable_qmu(struct ks_net *ks)
-{
- u16 w;
-
- w = ks_rdreg16(ks, KS_TXCR);
-
- /* Disables QMU Transmit (TXCR). */
- w &= ~TXCR_TXE;
- ks_wrreg16(ks, KS_TXCR, w);
-
- /* Disables QMU Receive (RXCR1). */
- w = ks_rdreg16(ks, KS_RXCR1);
- w &= ~RXCR1_RXE ;
- ks_wrreg16(ks, KS_RXCR1, w);
-
- ks->enabled = false;
-
-} /* ks_disable_qmu */
-
-/**
- * ks_read_qmu - read 1 pkt data from the QMU.
- * @ks: The chip information
- * @buf: buffer address to save 1 pkt
- * @len: Pkt length
- * Here is the sequence to read 1 pkt:
- * 1. set sudo DMA mode
- * 2. read prepend data
- * 3. read pkt data
- * 4. reset sudo DMA Mode
- */
-static inline void ks_read_qmu(struct ks_net *ks, u16 *buf, u32 len)
-{
- u32 r = ks->extra_byte & 0x1 ;
- u32 w = ks->extra_byte - r;
-
- /* 1. set sudo DMA mode */
- ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
- ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
-
- /* 2. read prepend data */
- /**
- * read 4 + extra bytes and discard them.
- * extra bytes for dummy, 2 for status, 2 for len
- */
-
- /* use likely(r) for 8 bit access for performance */
- if (unlikely(r))
- ioread8(ks->hw_addr);
- ks_inblk(ks, buf, w + 2 + 2);
-
- /* 3. read pkt data */
- ks_inblk(ks, buf, ALIGN(len, 4));
-
- /* 4. reset sudo DMA Mode */
- ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
-}
-
-/**
- * ks_rcv - read multiple pkts data from the QMU.
- * @ks: The chip information
- * @netdev: The network device being opened.
- *
- * Read all of header information before reading pkt content.
- * It is not allowed only port of pkts in QMU after issuing
- * interrupt ack.
- */
-static void ks_rcv(struct ks_net *ks, struct net_device *netdev)
-{
- u32 i;
- struct type_frame_head *frame_hdr = ks->frame_head_info;
- struct sk_buff *skb;
-
- ks->frame_cnt = ks_rdreg16(ks, KS_RXFCTR) >> 8;
-
- /* read all header information */
- for (i = 0; i < ks->frame_cnt; i++) {
- /* Checking Received packet status */
- frame_hdr->sts = ks_rdreg16(ks, KS_RXFHSR);
- /* Get packet len from hardware */
- frame_hdr->len = ks_rdreg16(ks, KS_RXFHBCR);
- frame_hdr++;
- }
-
- frame_hdr = ks->frame_head_info;
- while (ks->frame_cnt--) {
- skb = dev_alloc_skb(frame_hdr->len + 16);
- if (likely(skb && (frame_hdr->sts & RXFSHR_RXFV) &&
- (frame_hdr->len < RX_BUF_SIZE) && frame_hdr->len)) {
- skb_reserve(skb, 2);
- /* read data block including CRC 4 bytes */
- ks_read_qmu(ks, (u16 *)skb->data, frame_hdr->len);
- skb_put(skb, frame_hdr->len);
- skb->protocol = eth_type_trans(skb, netdev);
- netif_rx(skb);
- } else {
- pr_err("%s: err:skb alloc\n", __func__);
- ks_wrreg16(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_RRXEF));
- if (skb)
- dev_kfree_skb_irq(skb);
- }
- frame_hdr++;
- }
-}
-
-/**
- * ks_update_link_status - link status update.
- * @netdev: The network device being opened.
- * @ks: The chip information
- *
- */
-
-static void ks_update_link_status(struct net_device *netdev, struct ks_net *ks)
-{
- /* check the status of the link */
- u32 link_up_status;
- if (ks_rdreg16(ks, KS_P1SR) & P1SR_LINK_GOOD) {
- netif_carrier_on(netdev);
- link_up_status = true;
- } else {
- netif_carrier_off(netdev);
- link_up_status = false;
- }
- netif_dbg(ks, link, ks->netdev,
- "%s: %s\n", __func__, link_up_status ? "UP" : "DOWN");
-}
-
-/**
- * ks_irq - device interrupt handler
- * @irq: Interrupt number passed from the IRQ hnalder.
- * @pw: The private word passed to register_irq(), our struct ks_net.
- *
- * This is the handler invoked to find out what happened
- *
- * Read the interrupt status, work out what needs to be done and then clear
- * any of the interrupts that are not needed.
- */
-
-static irqreturn_t ks_irq(int irq, void *pw)
-{
- struct net_device *netdev = pw;
- struct ks_net *ks = netdev_priv(netdev);
- u16 status;
-
- /*this should be the first in IRQ handler */
- ks_save_cmd_reg(ks);
-
- status = ks_rdreg16(ks, KS_ISR);
- if (unlikely(!status)) {
- ks_restore_cmd_reg(ks);
- return IRQ_NONE;
- }
-
- ks_wrreg16(ks, KS_ISR, status);
-
- if (likely(status & IRQ_RXI))
- ks_rcv(ks, netdev);
-
- if (unlikely(status & IRQ_LCI))
- ks_update_link_status(netdev, ks);
-
- if (unlikely(status & IRQ_TXI))
- netif_wake_queue(netdev);
-
- if (unlikely(status & IRQ_LDI)) {
-
- u16 pmecr = ks_rdreg16(ks, KS_PMECR);
- pmecr &= ~PMECR_WKEVT_MASK;
- ks_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);
- }
-
- /* this should be the last in IRQ handler*/
- ks_restore_cmd_reg(ks);
- return IRQ_HANDLED;
-}
-
-
-/**
- * ks_net_open - open network device
- * @netdev: The network device being opened.
- *
- * Called when the network device is marked active, such as a user executing
- * 'ifconfig up' on the device.
- */
-static int ks_net_open(struct net_device *netdev)
-{
- struct ks_net *ks = netdev_priv(netdev);
- int err;
-
-#define KS_INT_FLAGS (IRQF_DISABLED|IRQF_TRIGGER_LOW)
- /* lock the card, even if we may not actually do anything
- * else at the moment.
- */
-
- netif_dbg(ks, ifup, ks->netdev, "%s - entry\n", __func__);
-
- /* reset the HW */
- err = request_irq(ks->irq, ks_irq, KS_INT_FLAGS, DRV_NAME, netdev);
-
- if (err) {
- pr_err("Failed to request IRQ: %d: %d\n", ks->irq, err);
- return err;
- }
-
- /* wake up powermode to normal mode */
- ks_set_powermode(ks, PMECR_PM_NORMAL);
- mdelay(1); /* wait for normal mode to take effect */
-
- ks_wrreg16(ks, KS_ISR, 0xffff);
- ks_enable_int(ks);
- ks_enable_qmu(ks);
- netif_start_queue(ks->netdev);
-
- netif_dbg(ks, ifup, ks->netdev, "network device up\n");
-
- return 0;
-}
-
-/**
- * ks_net_stop - close network device
- * @netdev: The device being closed.
- *
- * Called to close down a network device which has been active. Cancell any
- * work, shutdown the RX and TX process and then place the chip into a low
- * power state whilst it is not being used.
- */
-static int ks_net_stop(struct net_device *netdev)
-{
- struct ks_net *ks = netdev_priv(netdev);
-
- netif_info(ks, ifdown, netdev, "shutting down\n");
-
- netif_stop_queue(netdev);
-
- mutex_lock(&ks->lock);
-
- /* turn off the IRQs and ack any outstanding */
- ks_wrreg16(ks, KS_IER, 0x0000);
- ks_wrreg16(ks, KS_ISR, 0xffff);
-
- /* shutdown RX/TX QMU */
- ks_disable_qmu(ks);
-
- /* set powermode to soft power down to save power */
- ks_set_powermode(ks, PMECR_PM_SOFTDOWN);
- free_irq(ks->irq, netdev);
- mutex_unlock(&ks->lock);
- return 0;
-}
-
-
-/**
- * ks_write_qmu - write 1 pkt data to the QMU.
- * @ks: The chip information
- * @pdata: buffer address to save 1 pkt
- * @len: Pkt length in byte
- * Here is the sequence to write 1 pkt:
- * 1. set sudo DMA mode
- * 2. write status/length
- * 3. write pkt data
- * 4. reset sudo DMA Mode
- * 5. reset sudo DMA mode
- * 6. Wait until pkt is out
- */
-static void ks_write_qmu(struct ks_net *ks, u8 *pdata, u16 len)
-{
- /* start header at txb[0] to align txw entries */
- ks->txh.txw[0] = 0;
- ks->txh.txw[1] = cpu_to_le16(len);
-
- /* 1. set sudo-DMA mode */
- ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
- /* 2. write status/lenth info */
- ks_outblk(ks, ks->txh.txw, 4);
- /* 3. write pkt data */
- ks_outblk(ks, (u16 *)pdata, ALIGN(len, 4));
- /* 4. reset sudo-DMA mode */
- ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
- /* 5. Enqueue Tx(move the pkt from TX buffer into TXQ) */
- ks_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
- /* 6. wait until TXQCR_METFE is auto-cleared */
- while (ks_rdreg16(ks, KS_TXQCR) & TXQCR_METFE)
- ;
-}
-
-/**
- * ks_start_xmit - transmit packet
- * @skb : The buffer to transmit
- * @netdev : The device used to transmit the packet.
- *
- * Called by the network layer to transmit the @skb.
- * spin_lock_irqsave is required because tx and rx should be mutual exclusive.
- * So while tx is in-progress, prevent IRQ interrupt from happenning.
- */
-static int ks_start_xmit(struct sk_buff *skb, struct net_device *netdev)
-{
- int retv = NETDEV_TX_OK;
- struct ks_net *ks = netdev_priv(netdev);
-
- disable_irq(netdev->irq);
- ks_disable_int(ks);
- spin_lock(&ks->statelock);
-
- /* Extra space are required:
- * 4 byte for alignment, 4 for status/length, 4 for CRC
- */
-
- if (likely(ks_tx_fifo_space(ks) >= skb->len + 12)) {
- ks_write_qmu(ks, skb->data, skb->len);
- dev_kfree_skb(skb);
- } else
- retv = NETDEV_TX_BUSY;
- spin_unlock(&ks->statelock);
- ks_enable_int(ks);
- enable_irq(netdev->irq);
- return retv;
-}
-
-/**
- * ks_start_rx - ready to serve pkts
- * @ks : The chip information
- *
- */
-static void ks_start_rx(struct ks_net *ks)
-{
- u16 cntl;
-
- /* Enables QMU Receive (RXCR1). */
- cntl = ks_rdreg16(ks, KS_RXCR1);
- cntl |= RXCR1_RXE ;
- ks_wrreg16(ks, KS_RXCR1, cntl);
-} /* ks_start_rx */
-
-/**
- * ks_stop_rx - stop to serve pkts
- * @ks : The chip information
- *
- */
-static void ks_stop_rx(struct ks_net *ks)
-{
- u16 cntl;
-
- /* Disables QMU Receive (RXCR1). */
- cntl = ks_rdreg16(ks, KS_RXCR1);
- cntl &= ~RXCR1_RXE ;
- ks_wrreg16(ks, KS_RXCR1, cntl);
-
-} /* ks_stop_rx */
-
-static unsigned long const ethernet_polynomial = 0x04c11db7U;
-
-static unsigned long ether_gen_crc(int length, u8 *data)
-{
- long crc = -1;
- while (--length >= 0) {
- u8 current_octet = *data++;
- int bit;
-
- for (bit = 0; bit < 8; bit++, current_octet >>= 1) {
- crc = (crc << 1) ^
- ((crc < 0) ^ (current_octet & 1) ?
- ethernet_polynomial : 0);
- }
- }
- return (unsigned long)crc;
-} /* ether_gen_crc */
-
-/**
-* ks_set_grpaddr - set multicast information
-* @ks : The chip information
-*/
-
-static void ks_set_grpaddr(struct ks_net *ks)
-{
- u8 i;
- u32 index, position, value;
-
- memset(ks->mcast_bits, 0, sizeof(u8) * HW_MCAST_SIZE);
-
- for (i = 0; i < ks->mcast_lst_size; i++) {
- position = (ether_gen_crc(6, ks->mcast_lst[i]) >> 26) & 0x3f;
- index = position >> 3;
- value = 1 << (position & 7);
- ks->mcast_bits[index] |= (u8)value;
- }
-
- for (i = 0; i < HW_MCAST_SIZE; i++) {
- if (i & 1) {
- ks_wrreg16(ks, (u16)((KS_MAHTR0 + i) & ~1),
- (ks->mcast_bits[i] << 8) |
- ks->mcast_bits[i - 1]);
- }
- }
-} /* ks_set_grpaddr */
-
-/*
-* ks_clear_mcast - clear multicast information
-*
-* @ks : The chip information
-* This routine removes all mcast addresses set in the hardware.
-*/
-
-static void ks_clear_mcast(struct ks_net *ks)
-{
- u16 i, mcast_size;
- for (i = 0; i < HW_MCAST_SIZE; i++)
- ks->mcast_bits[i] = 0;
-
- mcast_size = HW_MCAST_SIZE >> 2;
- for (i = 0; i < mcast_size; i++)
- ks_wrreg16(ks, KS_MAHTR0 + (2*i), 0);
-}
-
-static void ks_set_promis(struct ks_net *ks, u16 promiscuous_mode)
-{
- u16 cntl;
- ks->promiscuous = promiscuous_mode;
- ks_stop_rx(ks); /* Stop receiving for reconfiguration */
- cntl = ks_rdreg16(ks, KS_RXCR1);
-
- cntl &= ~RXCR1_FILTER_MASK;
- if (promiscuous_mode)
- /* Enable Promiscuous mode */
- cntl |= RXCR1_RXAE | RXCR1_RXINVF;
- else
- /* Disable Promiscuous mode (default normal mode) */
- cntl |= RXCR1_RXPAFMA;
-
- ks_wrreg16(ks, KS_RXCR1, cntl);
-
- if (ks->enabled)
- ks_start_rx(ks);
-
-} /* ks_set_promis */
-
-static void ks_set_mcast(struct ks_net *ks, u16 mcast)
-{
- u16 cntl;
-
- ks->all_mcast = mcast;
- ks_stop_rx(ks); /* Stop receiving for reconfiguration */
- cntl = ks_rdreg16(ks, KS_RXCR1);
- cntl &= ~RXCR1_FILTER_MASK;
- if (mcast)
- /* Enable "Perfect with Multicast address passed mode" */
- cntl |= (RXCR1_RXAE | RXCR1_RXMAFMA | RXCR1_RXPAFMA);
- else
- /**
- * Disable "Perfect with Multicast address passed
- * mode" (normal mode).
- */
- cntl |= RXCR1_RXPAFMA;
-
- ks_wrreg16(ks, KS_RXCR1, cntl);
-
- if (ks->enabled)
- ks_start_rx(ks);
-} /* ks_set_mcast */
-
-static void ks_set_rx_mode(struct net_device *netdev)
-{
- struct ks_net *ks = netdev_priv(netdev);
- struct netdev_hw_addr *ha;
-
- /* Turn on/off promiscuous mode. */
- if ((netdev->flags & IFF_PROMISC) == IFF_PROMISC)
- ks_set_promis(ks,
- (u16)((netdev->flags & IFF_PROMISC) == IFF_PROMISC));
- /* Turn on/off all mcast mode. */
- else if ((netdev->flags & IFF_ALLMULTI) == IFF_ALLMULTI)
- ks_set_mcast(ks,
- (u16)((netdev->flags & IFF_ALLMULTI) == IFF_ALLMULTI));
- else
- ks_set_promis(ks, false);
-
- if ((netdev->flags & IFF_MULTICAST) && netdev_mc_count(netdev)) {
- if (netdev_mc_count(netdev) <= MAX_MCAST_LST) {
- int i = 0;
-
- netdev_for_each_mc_addr(ha, netdev) {
- if (i >= MAX_MCAST_LST)
- break;
- memcpy(ks->mcast_lst[i++], ha->addr, ETH_ALEN);
- }
- ks->mcast_lst_size = (u8)i;
- ks_set_grpaddr(ks);
- } else {
- /**
- * List too big to support so
- * turn on all mcast mode.
- */
- ks->mcast_lst_size = MAX_MCAST_LST;
- ks_set_mcast(ks, true);
- }
- } else {
- ks->mcast_lst_size = 0;
- ks_clear_mcast(ks);
- }
-} /* ks_set_rx_mode */
-
-static void ks_set_mac(struct ks_net *ks, u8 *data)
-{
- u16 *pw = (u16 *)data;
- u16 w, u;
-
- ks_stop_rx(ks); /* Stop receiving for reconfiguration */
-
- u = *pw++;
- w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
- ks_wrreg16(ks, KS_MARH, w);
-
- u = *pw++;
- w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
- ks_wrreg16(ks, KS_MARM, w);
-
- u = *pw;
- w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
- ks_wrreg16(ks, KS_MARL, w);
-
- memcpy(ks->mac_addr, data, 6);
-
- if (ks->enabled)
- ks_start_rx(ks);
-}
-
-static int ks_set_mac_address(struct net_device *netdev, void *paddr)
-{
- struct ks_net *ks = netdev_priv(netdev);
- struct sockaddr *addr = paddr;
- u8 *da;
-
- memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
-
- da = (u8 *)netdev->dev_addr;
-
- ks_set_mac(ks, da);
- return 0;
-}
-
-static int ks_net_ioctl(struct net_device *netdev, struct ifreq *req, int cmd)
-{
- struct ks_net *ks = netdev_priv(netdev);
-
- if (!netif_running(netdev))
- return -EINVAL;
-
- return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
-}
-
-static const struct net_device_ops ks_netdev_ops = {
- .ndo_open = ks_net_open,
- .ndo_stop = ks_net_stop,
- .ndo_do_ioctl = ks_net_ioctl,
- .ndo_start_xmit = ks_start_xmit,
- .ndo_set_mac_address = ks_set_mac_address,
- .ndo_set_rx_mode = ks_set_rx_mode,
- .ndo_change_mtu = eth_change_mtu,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-/* ethtool support */
-
-static void ks_get_drvinfo(struct net_device *netdev,
- struct ethtool_drvinfo *di)
-{
- strlcpy(di->driver, DRV_NAME, sizeof(di->driver));
- strlcpy(di->version, "1.00", sizeof(di->version));
- strlcpy(di->bus_info, dev_name(netdev->dev.parent),
- sizeof(di->bus_info));
-}
-
-static u32 ks_get_msglevel(struct net_device *netdev)
-{
- struct ks_net *ks = netdev_priv(netdev);
- return ks->msg_enable;
-}
-
-static void ks_set_msglevel(struct net_device *netdev, u32 to)
-{
- struct ks_net *ks = netdev_priv(netdev);
- ks->msg_enable = to;
-}
-
-static int ks_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
-{
- struct ks_net *ks = netdev_priv(netdev);
- return mii_ethtool_gset(&ks->mii, cmd);
-}
-
-static int ks_set_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
-{
- struct ks_net *ks = netdev_priv(netdev);
- return mii_ethtool_sset(&ks->mii, cmd);
-}
-
-static u32 ks_get_link(struct net_device *netdev)
-{
- struct ks_net *ks = netdev_priv(netdev);
- return mii_link_ok(&ks->mii);
-}
-
-static int ks_nway_reset(struct net_device *netdev)
-{
- struct ks_net *ks = netdev_priv(netdev);
- return mii_nway_restart(&ks->mii);
-}
-
-static const struct ethtool_ops ks_ethtool_ops = {
- .get_drvinfo = ks_get_drvinfo,
- .get_msglevel = ks_get_msglevel,
- .set_msglevel = ks_set_msglevel,
- .get_settings = ks_get_settings,
- .set_settings = ks_set_settings,
- .get_link = ks_get_link,
- .nway_reset = ks_nway_reset,
-};
-
-/* MII interface controls */
-
-/**
- * ks_phy_reg - convert MII register into a KS8851 register
- * @reg: MII register number.
- *
- * Return the KS8851 register number for the corresponding MII PHY register
- * if possible. Return zero if the MII register has no direct mapping to the
- * KS8851 register set.
- */
-static int ks_phy_reg(int reg)
-{
- switch (reg) {
- case MII_BMCR:
- return KS_P1MBCR;
- case MII_BMSR:
- return KS_P1MBSR;
- case MII_PHYSID1:
- return KS_PHY1ILR;
- case MII_PHYSID2:
- return KS_PHY1IHR;
- case MII_ADVERTISE:
- return KS_P1ANAR;
- case MII_LPA:
- return KS_P1ANLPR;
- }
-
- return 0x0;
-}
-
-/**
- * ks_phy_read - MII interface PHY register read.
- * @netdev: The network device the PHY is on.
- * @phy_addr: Address of PHY (ignored as we only have one)
- * @reg: The register to read.
- *
- * This call reads data from the PHY register specified in @reg. Since the
- * device does not support all the MII registers, the non-existent values
- * are always returned as zero.
- *
- * We return zero for unsupported registers as the MII code does not check
- * the value returned for any error status, and simply returns it to the
- * caller. The mii-tool that the driver was tested with takes any -ve error
- * as real PHY capabilities, thus displaying incorrect data to the user.
- */
-static int ks_phy_read(struct net_device *netdev, int phy_addr, int reg)
-{
- struct ks_net *ks = netdev_priv(netdev);
- int ksreg;
- int result;
-
- ksreg = ks_phy_reg(reg);
- if (!ksreg)
- return 0x0; /* no error return allowed, so use zero */
-
- mutex_lock(&ks->lock);
- result = ks_rdreg16(ks, ksreg);
- mutex_unlock(&ks->lock);
-
- return result;
-}
-
-static void ks_phy_write(struct net_device *netdev,
- int phy, int reg, int value)
-{
- struct ks_net *ks = netdev_priv(netdev);
- int ksreg;
-
- ksreg = ks_phy_reg(reg);
- if (ksreg) {
- mutex_lock(&ks->lock);
- ks_wrreg16(ks, ksreg, value);
- mutex_unlock(&ks->lock);
- }
-}
-
-/**
- * ks_read_selftest - read the selftest memory info.
- * @ks: The device state
- *
- * Read and check the TX/RX memory selftest information.
- */
-static int ks_read_selftest(struct ks_net *ks)
-{
- unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
- int ret = 0;
- unsigned rd;
-
- rd = ks_rdreg16(ks, KS_MBIR);
-
- if ((rd & both_done) != both_done) {
- netdev_warn(ks->netdev, "Memory selftest not finished\n");
- return 0;
- }
-
- if (rd & MBIR_TXMBFA) {
- netdev_err(ks->netdev, "TX memory selftest fails\n");
- ret |= 1;
- }
-
- if (rd & MBIR_RXMBFA) {
- netdev_err(ks->netdev, "RX memory selftest fails\n");
- ret |= 2;
- }
-
- netdev_info(ks->netdev, "the selftest passes\n");
- return ret;
-}
-
-static void ks_setup(struct ks_net *ks)
-{
- u16 w;
-
- /**
- * Configure QMU Transmit
- */
-
- /* Setup Transmit Frame Data Pointer Auto-Increment (TXFDPR) */
- ks_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);
-
- /* Setup Receive Frame Data Pointer Auto-Increment */
- ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
-
- /* Setup Receive Frame Threshold - 1 frame (RXFCTFC) */
- ks_wrreg16(ks, KS_RXFCTR, 1 & RXFCTR_THRESHOLD_MASK);
-
- /* Setup RxQ Command Control (RXQCR) */
- ks->rc_rxqcr = RXQCR_CMD_CNTL;
- ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
-
- /**
- * set the force mode to half duplex, default is full duplex
- * because if the auto-negotiation fails, most switch uses
- * half-duplex.
- */
-
- w = ks_rdreg16(ks, KS_P1MBCR);
- w &= ~P1MBCR_FORCE_FDX;
- ks_wrreg16(ks, KS_P1MBCR, w);
-
- w = TXCR_TXFCE | TXCR_TXPE | TXCR_TXCRC | TXCR_TCGIP;
- ks_wrreg16(ks, KS_TXCR, w);
-
- w = RXCR1_RXFCE | RXCR1_RXBE | RXCR1_RXUE | RXCR1_RXME | RXCR1_RXIPFCC;
-
- if (ks->promiscuous) /* bPromiscuous */
- w |= (RXCR1_RXAE | RXCR1_RXINVF);
- else if (ks->all_mcast) /* Multicast address passed mode */
- w |= (RXCR1_RXAE | RXCR1_RXMAFMA | RXCR1_RXPAFMA);
- else /* Normal mode */
- w |= RXCR1_RXPAFMA;
-
- ks_wrreg16(ks, KS_RXCR1, w);
-} /*ks_setup */
-
-
-static void ks_setup_int(struct ks_net *ks)
-{
- ks->rc_ier = 0x00;
- /* Clear the interrupts status of the hardware. */
- ks_wrreg16(ks, KS_ISR, 0xffff);
-
- /* Enables the interrupts of the hardware. */
- ks->rc_ier = (IRQ_LCI | IRQ_TXI | IRQ_RXI);
-} /* ks_setup_int */
-
-static int ks_hw_init(struct ks_net *ks)
-{
-#define MHEADER_SIZE (sizeof(struct type_frame_head) * MAX_RECV_FRAMES)
- ks->promiscuous = 0;
- ks->all_mcast = 0;
- ks->mcast_lst_size = 0;
-
- ks->frame_head_info = (struct type_frame_head *) \
- kmalloc(MHEADER_SIZE, GFP_KERNEL);
- if (!ks->frame_head_info) {
- pr_err("Error: Fail to allocate frame memory\n");
- return false;
- }
-
- ks_set_mac(ks, KS_DEFAULT_MAC_ADDRESS);
- return true;
-}
-
-
-static int __devinit ks8851_probe(struct platform_device *pdev)
-{
- int err = -ENOMEM;
- struct resource *io_d, *io_c;
- struct net_device *netdev;
- struct ks_net *ks;
- u16 id, data;
-
- io_d = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- io_c = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-
- if (!request_mem_region(io_d->start, resource_size(io_d), DRV_NAME))
- goto err_mem_region;
-
- if (!request_mem_region(io_c->start, resource_size(io_c), DRV_NAME))
- goto err_mem_region1;
-
- netdev = alloc_etherdev(sizeof(struct ks_net));
- if (!netdev)
- goto err_alloc_etherdev;
-
- SET_NETDEV_DEV(netdev, &pdev->dev);
-
- ks = netdev_priv(netdev);
- ks->netdev = netdev;
- ks->hw_addr = ioremap(io_d->start, resource_size(io_d));
-
- if (!ks->hw_addr)
- goto err_ioremap;
-
- ks->hw_addr_cmd = ioremap(io_c->start, resource_size(io_c));
- if (!ks->hw_addr_cmd)
- goto err_ioremap1;
-
- ks->irq = platform_get_irq(pdev, 0);
-
- if (ks->irq < 0) {
- err = ks->irq;
- goto err_get_irq;
- }
-
- ks->pdev = pdev;
-
- mutex_init(&ks->lock);
- spin_lock_init(&ks->statelock);
-
- netdev->netdev_ops = &ks_netdev_ops;
- netdev->ethtool_ops = &ks_ethtool_ops;
-
- /* setup mii state */
- ks->mii.dev = netdev;
- ks->mii.phy_id = 1,
- ks->mii.phy_id_mask = 1;
- ks->mii.reg_num_mask = 0xf;
- ks->mii.mdio_read = ks_phy_read;
- ks->mii.mdio_write = ks_phy_write;
-
- netdev_info(netdev, "message enable is %d\n", msg_enable);
- /* set the default message enable */
- ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
- NETIF_MSG_PROBE |
- NETIF_MSG_LINK));
- ks_read_config(ks);
-
- /* simple check for a valid chip being connected to the bus */
- if ((ks_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
- netdev_err(netdev, "failed to read device ID\n");
- err = -ENODEV;
- goto err_register;
- }
-
- if (ks_read_selftest(ks)) {
- netdev_err(netdev, "failed to read device ID\n");
- err = -ENODEV;
- goto err_register;
- }
-
- err = register_netdev(netdev);
- if (err)
- goto err_register;
-
- platform_set_drvdata(pdev, netdev);
-
- ks_soft_reset(ks, GRR_GSR);
- ks_hw_init(ks);
- ks_disable_qmu(ks);
- ks_setup(ks);
- ks_setup_int(ks);
- memcpy(netdev->dev_addr, ks->mac_addr, 6);
-
- data = ks_rdreg16(ks, KS_OBCR);
- ks_wrreg16(ks, KS_OBCR, data | OBCR_ODS_16MA);
-
- /**
- * If you want to use the default MAC addr,
- * comment out the 2 functions below.
- */
-
- random_ether_addr(netdev->dev_addr);
- ks_set_mac(ks, netdev->dev_addr);
-
- id = ks_rdreg16(ks, KS_CIDER);
-
- netdev_info(netdev, "Found chip, family: 0x%x, id: 0x%x, rev: 0x%x\n",
- (id >> 8) & 0xff, (id >> 4) & 0xf, (id >> 1) & 0x7);
- return 0;
-
-err_register:
-err_get_irq:
- iounmap(ks->hw_addr_cmd);
-err_ioremap1:
- iounmap(ks->hw_addr);
-err_ioremap:
- free_netdev(netdev);
-err_alloc_etherdev:
- release_mem_region(io_c->start, resource_size(io_c));
-err_mem_region1:
- release_mem_region(io_d->start, resource_size(io_d));
-err_mem_region:
- return err;
-}
-
-static int __devexit ks8851_remove(struct platform_device *pdev)
-{
- struct net_device *netdev = platform_get_drvdata(pdev);
- struct ks_net *ks = netdev_priv(netdev);
- struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
- kfree(ks->frame_head_info);
- unregister_netdev(netdev);
- iounmap(ks->hw_addr);
- free_netdev(netdev);
- release_mem_region(iomem->start, resource_size(iomem));
- platform_set_drvdata(pdev, NULL);
- return 0;
-
-}
-
-static struct platform_driver ks8851_platform_driver = {
- .driver = {
- .name = DRV_NAME,
- .owner = THIS_MODULE,
- },
- .probe = ks8851_probe,
- .remove = __devexit_p(ks8851_remove),
-};
-
-static int __init ks8851_init(void)
-{
- return platform_driver_register(&ks8851_platform_driver);
-}
-
-static void __exit ks8851_exit(void)
-{
- platform_driver_unregister(&ks8851_platform_driver);
-}
-
-module_init(ks8851_init);
-module_exit(ks8851_exit);
-
-MODULE_DESCRIPTION("KS8851 MLL Network driver");
-MODULE_AUTHOR("David Choi <david.choi@micrel.com>");
-MODULE_LICENSE("GPL");
-module_param_named(message, msg_enable, int, 0);
-MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
-
+++ /dev/null
-/**
- * drivers/net/ksx884x.c - Micrel KSZ8841/2 PCI Ethernet driver
- *
- * Copyright (c) 2009-2010 Micrel, Inc.
- * Tristram Ha <Tristram.Ha@micrel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/pci.h>
-#include <linux/proc_fs.h>
-#include <linux/mii.h>
-#include <linux/platform_device.h>
-#include <linux/ethtool.h>
-#include <linux/etherdevice.h>
-#include <linux/in.h>
-#include <linux/ip.h>
-#include <linux/if_vlan.h>
-#include <linux/crc32.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-
-
-/* DMA Registers */
-
-#define KS_DMA_TX_CTRL 0x0000
-#define DMA_TX_ENABLE 0x00000001
-#define DMA_TX_CRC_ENABLE 0x00000002
-#define DMA_TX_PAD_ENABLE 0x00000004
-#define DMA_TX_LOOPBACK 0x00000100
-#define DMA_TX_FLOW_ENABLE 0x00000200
-#define DMA_TX_CSUM_IP 0x00010000
-#define DMA_TX_CSUM_TCP 0x00020000
-#define DMA_TX_CSUM_UDP 0x00040000
-#define DMA_TX_BURST_SIZE 0x3F000000
-
-#define KS_DMA_RX_CTRL 0x0004
-#define DMA_RX_ENABLE 0x00000001
-#define KS884X_DMA_RX_MULTICAST 0x00000002
-#define DMA_RX_PROMISCUOUS 0x00000004
-#define DMA_RX_ERROR 0x00000008
-#define DMA_RX_UNICAST 0x00000010
-#define DMA_RX_ALL_MULTICAST 0x00000020
-#define DMA_RX_BROADCAST 0x00000040
-#define DMA_RX_FLOW_ENABLE 0x00000200
-#define DMA_RX_CSUM_IP 0x00010000
-#define DMA_RX_CSUM_TCP 0x00020000
-#define DMA_RX_CSUM_UDP 0x00040000
-#define DMA_RX_BURST_SIZE 0x3F000000
-
-#define DMA_BURST_SHIFT 24
-#define DMA_BURST_DEFAULT 8
-
-#define KS_DMA_TX_START 0x0008
-#define KS_DMA_RX_START 0x000C
-#define DMA_START 0x00000001
-
-#define KS_DMA_TX_ADDR 0x0010
-#define KS_DMA_RX_ADDR 0x0014
-
-#define DMA_ADDR_LIST_MASK 0xFFFFFFFC
-#define DMA_ADDR_LIST_SHIFT 2
-
-/* MTR0 */
-#define KS884X_MULTICAST_0_OFFSET 0x0020
-#define KS884X_MULTICAST_1_OFFSET 0x0021
-#define KS884X_MULTICAST_2_OFFSET 0x0022
-#define KS884x_MULTICAST_3_OFFSET 0x0023
-/* MTR1 */
-#define KS884X_MULTICAST_4_OFFSET 0x0024
-#define KS884X_MULTICAST_5_OFFSET 0x0025
-#define KS884X_MULTICAST_6_OFFSET 0x0026
-#define KS884X_MULTICAST_7_OFFSET 0x0027
-
-/* Interrupt Registers */
-
-/* INTEN */
-#define KS884X_INTERRUPTS_ENABLE 0x0028
-/* INTST */
-#define KS884X_INTERRUPTS_STATUS 0x002C
-
-#define KS884X_INT_RX_STOPPED 0x02000000
-#define KS884X_INT_TX_STOPPED 0x04000000
-#define KS884X_INT_RX_OVERRUN 0x08000000
-#define KS884X_INT_TX_EMPTY 0x10000000
-#define KS884X_INT_RX 0x20000000
-#define KS884X_INT_TX 0x40000000
-#define KS884X_INT_PHY 0x80000000
-
-#define KS884X_INT_RX_MASK \
- (KS884X_INT_RX | KS884X_INT_RX_OVERRUN)
-#define KS884X_INT_TX_MASK \
- (KS884X_INT_TX | KS884X_INT_TX_EMPTY)
-#define KS884X_INT_MASK (KS884X_INT_RX | KS884X_INT_TX | KS884X_INT_PHY)
-
-/* MAC Additional Station Address */
-
-/* MAAL0 */
-#define KS_ADD_ADDR_0_LO 0x0080
-/* MAAH0 */
-#define KS_ADD_ADDR_0_HI 0x0084
-/* MAAL1 */
-#define KS_ADD_ADDR_1_LO 0x0088
-/* MAAH1 */
-#define KS_ADD_ADDR_1_HI 0x008C
-/* MAAL2 */
-#define KS_ADD_ADDR_2_LO 0x0090
-/* MAAH2 */
-#define KS_ADD_ADDR_2_HI 0x0094
-/* MAAL3 */
-#define KS_ADD_ADDR_3_LO 0x0098
-/* MAAH3 */
-#define KS_ADD_ADDR_3_HI 0x009C
-/* MAAL4 */
-#define KS_ADD_ADDR_4_LO 0x00A0
-/* MAAH4 */
-#define KS_ADD_ADDR_4_HI 0x00A4
-/* MAAL5 */
-#define KS_ADD_ADDR_5_LO 0x00A8
-/* MAAH5 */
-#define KS_ADD_ADDR_5_HI 0x00AC
-/* MAAL6 */
-#define KS_ADD_ADDR_6_LO 0x00B0
-/* MAAH6 */
-#define KS_ADD_ADDR_6_HI 0x00B4
-/* MAAL7 */
-#define KS_ADD_ADDR_7_LO 0x00B8
-/* MAAH7 */
-#define KS_ADD_ADDR_7_HI 0x00BC
-/* MAAL8 */
-#define KS_ADD_ADDR_8_LO 0x00C0
-/* MAAH8 */
-#define KS_ADD_ADDR_8_HI 0x00C4
-/* MAAL9 */
-#define KS_ADD_ADDR_9_LO 0x00C8
-/* MAAH9 */
-#define KS_ADD_ADDR_9_HI 0x00CC
-/* MAAL10 */
-#define KS_ADD_ADDR_A_LO 0x00D0
-/* MAAH10 */
-#define KS_ADD_ADDR_A_HI 0x00D4
-/* MAAL11 */
-#define KS_ADD_ADDR_B_LO 0x00D8
-/* MAAH11 */
-#define KS_ADD_ADDR_B_HI 0x00DC
-/* MAAL12 */
-#define KS_ADD_ADDR_C_LO 0x00E0
-/* MAAH12 */
-#define KS_ADD_ADDR_C_HI 0x00E4
-/* MAAL13 */
-#define KS_ADD_ADDR_D_LO 0x00E8
-/* MAAH13 */
-#define KS_ADD_ADDR_D_HI 0x00EC
-/* MAAL14 */
-#define KS_ADD_ADDR_E_LO 0x00F0
-/* MAAH14 */
-#define KS_ADD_ADDR_E_HI 0x00F4
-/* MAAL15 */
-#define KS_ADD_ADDR_F_LO 0x00F8
-/* MAAH15 */
-#define KS_ADD_ADDR_F_HI 0x00FC
-
-#define ADD_ADDR_HI_MASK 0x0000FFFF
-#define ADD_ADDR_ENABLE 0x80000000
-#define ADD_ADDR_INCR 8
-
-/* Miscellaneous Registers */
-
-/* MARL */
-#define KS884X_ADDR_0_OFFSET 0x0200
-#define KS884X_ADDR_1_OFFSET 0x0201
-/* MARM */
-#define KS884X_ADDR_2_OFFSET 0x0202
-#define KS884X_ADDR_3_OFFSET 0x0203
-/* MARH */
-#define KS884X_ADDR_4_OFFSET 0x0204
-#define KS884X_ADDR_5_OFFSET 0x0205
-
-/* OBCR */
-#define KS884X_BUS_CTRL_OFFSET 0x0210
-
-#define BUS_SPEED_125_MHZ 0x0000
-#define BUS_SPEED_62_5_MHZ 0x0001
-#define BUS_SPEED_41_66_MHZ 0x0002
-#define BUS_SPEED_25_MHZ 0x0003
-
-/* EEPCR */
-#define KS884X_EEPROM_CTRL_OFFSET 0x0212
-
-#define EEPROM_CHIP_SELECT 0x0001
-#define EEPROM_SERIAL_CLOCK 0x0002
-#define EEPROM_DATA_OUT 0x0004
-#define EEPROM_DATA_IN 0x0008
-#define EEPROM_ACCESS_ENABLE 0x0010
-
-/* MBIR */
-#define KS884X_MEM_INFO_OFFSET 0x0214
-
-#define RX_MEM_TEST_FAILED 0x0008
-#define RX_MEM_TEST_FINISHED 0x0010
-#define TX_MEM_TEST_FAILED 0x0800
-#define TX_MEM_TEST_FINISHED 0x1000
-
-/* GCR */
-#define KS884X_GLOBAL_CTRL_OFFSET 0x0216
-#define GLOBAL_SOFTWARE_RESET 0x0001
-
-#define KS8841_POWER_MANAGE_OFFSET 0x0218
-
-/* WFCR */
-#define KS8841_WOL_CTRL_OFFSET 0x021A
-#define KS8841_WOL_MAGIC_ENABLE 0x0080
-#define KS8841_WOL_FRAME3_ENABLE 0x0008
-#define KS8841_WOL_FRAME2_ENABLE 0x0004
-#define KS8841_WOL_FRAME1_ENABLE 0x0002
-#define KS8841_WOL_FRAME0_ENABLE 0x0001
-
-/* WF0 */
-#define KS8841_WOL_FRAME_CRC_OFFSET 0x0220
-#define KS8841_WOL_FRAME_BYTE0_OFFSET 0x0224
-#define KS8841_WOL_FRAME_BYTE2_OFFSET 0x0228
-
-/* IACR */
-#define KS884X_IACR_P 0x04A0
-#define KS884X_IACR_OFFSET KS884X_IACR_P
-
-/* IADR1 */
-#define KS884X_IADR1_P 0x04A2
-#define KS884X_IADR2_P 0x04A4
-#define KS884X_IADR3_P 0x04A6
-#define KS884X_IADR4_P 0x04A8
-#define KS884X_IADR5_P 0x04AA
-
-#define KS884X_ACC_CTRL_SEL_OFFSET KS884X_IACR_P
-#define KS884X_ACC_CTRL_INDEX_OFFSET (KS884X_ACC_CTRL_SEL_OFFSET + 1)
-
-#define KS884X_ACC_DATA_0_OFFSET KS884X_IADR4_P
-#define KS884X_ACC_DATA_1_OFFSET (KS884X_ACC_DATA_0_OFFSET + 1)
-#define KS884X_ACC_DATA_2_OFFSET KS884X_IADR5_P
-#define KS884X_ACC_DATA_3_OFFSET (KS884X_ACC_DATA_2_OFFSET + 1)
-#define KS884X_ACC_DATA_4_OFFSET KS884X_IADR2_P
-#define KS884X_ACC_DATA_5_OFFSET (KS884X_ACC_DATA_4_OFFSET + 1)
-#define KS884X_ACC_DATA_6_OFFSET KS884X_IADR3_P
-#define KS884X_ACC_DATA_7_OFFSET (KS884X_ACC_DATA_6_OFFSET + 1)
-#define KS884X_ACC_DATA_8_OFFSET KS884X_IADR1_P
-
-/* P1MBCR */
-#define KS884X_P1MBCR_P 0x04D0
-#define KS884X_P1MBSR_P 0x04D2
-#define KS884X_PHY1ILR_P 0x04D4
-#define KS884X_PHY1IHR_P 0x04D6
-#define KS884X_P1ANAR_P 0x04D8
-#define KS884X_P1ANLPR_P 0x04DA
-
-/* P2MBCR */
-#define KS884X_P2MBCR_P 0x04E0
-#define KS884X_P2MBSR_P 0x04E2
-#define KS884X_PHY2ILR_P 0x04E4
-#define KS884X_PHY2IHR_P 0x04E6
-#define KS884X_P2ANAR_P 0x04E8
-#define KS884X_P2ANLPR_P 0x04EA
-
-#define KS884X_PHY_1_CTRL_OFFSET KS884X_P1MBCR_P
-#define PHY_CTRL_INTERVAL (KS884X_P2MBCR_P - KS884X_P1MBCR_P)
-
-#define KS884X_PHY_CTRL_OFFSET 0x00
-
-/* Mode Control Register */
-#define PHY_REG_CTRL 0
-
-#define PHY_RESET 0x8000
-#define PHY_LOOPBACK 0x4000
-#define PHY_SPEED_100MBIT 0x2000
-#define PHY_AUTO_NEG_ENABLE 0x1000
-#define PHY_POWER_DOWN 0x0800
-#define PHY_MII_DISABLE 0x0400
-#define PHY_AUTO_NEG_RESTART 0x0200
-#define PHY_FULL_DUPLEX 0x0100
-#define PHY_COLLISION_TEST 0x0080
-#define PHY_HP_MDIX 0x0020
-#define PHY_FORCE_MDIX 0x0010
-#define PHY_AUTO_MDIX_DISABLE 0x0008
-#define PHY_REMOTE_FAULT_DISABLE 0x0004
-#define PHY_TRANSMIT_DISABLE 0x0002
-#define PHY_LED_DISABLE 0x0001
-
-#define KS884X_PHY_STATUS_OFFSET 0x02
-
-/* Mode Status Register */
-#define PHY_REG_STATUS 1
-
-#define PHY_100BT4_CAPABLE 0x8000
-#define PHY_100BTX_FD_CAPABLE 0x4000
-#define PHY_100BTX_CAPABLE 0x2000
-#define PHY_10BT_FD_CAPABLE 0x1000
-#define PHY_10BT_CAPABLE 0x0800
-#define PHY_MII_SUPPRESS_CAPABLE 0x0040
-#define PHY_AUTO_NEG_ACKNOWLEDGE 0x0020
-#define PHY_REMOTE_FAULT 0x0010
-#define PHY_AUTO_NEG_CAPABLE 0x0008
-#define PHY_LINK_STATUS 0x0004
-#define PHY_JABBER_DETECT 0x0002
-#define PHY_EXTENDED_CAPABILITY 0x0001
-
-#define KS884X_PHY_ID_1_OFFSET 0x04
-#define KS884X_PHY_ID_2_OFFSET 0x06
-
-/* PHY Identifier Registers */
-#define PHY_REG_ID_1 2
-#define PHY_REG_ID_2 3
-
-#define KS884X_PHY_AUTO_NEG_OFFSET 0x08
-
-/* Auto-Negotiation Advertisement Register */
-#define PHY_REG_AUTO_NEGOTIATION 4
-
-#define PHY_AUTO_NEG_NEXT_PAGE 0x8000
-#define PHY_AUTO_NEG_REMOTE_FAULT 0x2000
-/* Not supported. */
-#define PHY_AUTO_NEG_ASYM_PAUSE 0x0800
-#define PHY_AUTO_NEG_SYM_PAUSE 0x0400
-#define PHY_AUTO_NEG_100BT4 0x0200
-#define PHY_AUTO_NEG_100BTX_FD 0x0100
-#define PHY_AUTO_NEG_100BTX 0x0080
-#define PHY_AUTO_NEG_10BT_FD 0x0040
-#define PHY_AUTO_NEG_10BT 0x0020
-#define PHY_AUTO_NEG_SELECTOR 0x001F
-#define PHY_AUTO_NEG_802_3 0x0001
-
-#define PHY_AUTO_NEG_PAUSE (PHY_AUTO_NEG_SYM_PAUSE | PHY_AUTO_NEG_ASYM_PAUSE)
-
-#define KS884X_PHY_REMOTE_CAP_OFFSET 0x0A
-
-/* Auto-Negotiation Link Partner Ability Register */
-#define PHY_REG_REMOTE_CAPABILITY 5
-
-#define PHY_REMOTE_NEXT_PAGE 0x8000
-#define PHY_REMOTE_ACKNOWLEDGE 0x4000
-#define PHY_REMOTE_REMOTE_FAULT 0x2000
-#define PHY_REMOTE_SYM_PAUSE 0x0400
-#define PHY_REMOTE_100BTX_FD 0x0100
-#define PHY_REMOTE_100BTX 0x0080
-#define PHY_REMOTE_10BT_FD 0x0040
-#define PHY_REMOTE_10BT 0x0020
-
-/* P1VCT */
-#define KS884X_P1VCT_P 0x04F0
-#define KS884X_P1PHYCTRL_P 0x04F2
-
-/* P2VCT */
-#define KS884X_P2VCT_P 0x04F4
-#define KS884X_P2PHYCTRL_P 0x04F6
-
-#define KS884X_PHY_SPECIAL_OFFSET KS884X_P1VCT_P
-#define PHY_SPECIAL_INTERVAL (KS884X_P2VCT_P - KS884X_P1VCT_P)
-
-#define KS884X_PHY_LINK_MD_OFFSET 0x00
-
-#define PHY_START_CABLE_DIAG 0x8000
-#define PHY_CABLE_DIAG_RESULT 0x6000
-#define PHY_CABLE_STAT_NORMAL 0x0000
-#define PHY_CABLE_STAT_OPEN 0x2000
-#define PHY_CABLE_STAT_SHORT 0x4000
-#define PHY_CABLE_STAT_FAILED 0x6000
-#define PHY_CABLE_10M_SHORT 0x1000
-#define PHY_CABLE_FAULT_COUNTER 0x01FF
-
-#define KS884X_PHY_PHY_CTRL_OFFSET 0x02
-
-#define PHY_STAT_REVERSED_POLARITY 0x0020
-#define PHY_STAT_MDIX 0x0010
-#define PHY_FORCE_LINK 0x0008
-#define PHY_POWER_SAVING_DISABLE 0x0004
-#define PHY_REMOTE_LOOPBACK 0x0002
-
-/* SIDER */
-#define KS884X_SIDER_P 0x0400
-#define KS884X_CHIP_ID_OFFSET KS884X_SIDER_P
-#define KS884X_FAMILY_ID_OFFSET (KS884X_CHIP_ID_OFFSET + 1)
-
-#define REG_FAMILY_ID 0x88
-
-#define REG_CHIP_ID_41 0x8810
-#define REG_CHIP_ID_42 0x8800
-
-#define KS884X_CHIP_ID_MASK_41 0xFF10
-#define KS884X_CHIP_ID_MASK 0xFFF0
-#define KS884X_CHIP_ID_SHIFT 4
-#define KS884X_REVISION_MASK 0x000E
-#define KS884X_REVISION_SHIFT 1
-#define KS8842_START 0x0001
-
-#define CHIP_IP_41_M 0x8810
-#define CHIP_IP_42_M 0x8800
-#define CHIP_IP_61_M 0x8890
-#define CHIP_IP_62_M 0x8880
-
-#define CHIP_IP_41_P 0x8850
-#define CHIP_IP_42_P 0x8840
-#define CHIP_IP_61_P 0x88D0
-#define CHIP_IP_62_P 0x88C0
-
-/* SGCR1 */
-#define KS8842_SGCR1_P 0x0402
-#define KS8842_SWITCH_CTRL_1_OFFSET KS8842_SGCR1_P
-
-#define SWITCH_PASS_ALL 0x8000
-#define SWITCH_TX_FLOW_CTRL 0x2000
-#define SWITCH_RX_FLOW_CTRL 0x1000
-#define SWITCH_CHECK_LENGTH 0x0800
-#define SWITCH_AGING_ENABLE 0x0400
-#define SWITCH_FAST_AGING 0x0200
-#define SWITCH_AGGR_BACKOFF 0x0100
-#define SWITCH_PASS_PAUSE 0x0008
-#define SWITCH_LINK_AUTO_AGING 0x0001
-
-/* SGCR2 */
-#define KS8842_SGCR2_P 0x0404
-#define KS8842_SWITCH_CTRL_2_OFFSET KS8842_SGCR2_P
-
-#define SWITCH_VLAN_ENABLE 0x8000
-#define SWITCH_IGMP_SNOOP 0x4000
-#define IPV6_MLD_SNOOP_ENABLE 0x2000
-#define IPV6_MLD_SNOOP_OPTION 0x1000
-#define PRIORITY_SCHEME_SELECT 0x0800
-#define SWITCH_MIRROR_RX_TX 0x0100
-#define UNICAST_VLAN_BOUNDARY 0x0080
-#define MULTICAST_STORM_DISABLE 0x0040
-#define SWITCH_BACK_PRESSURE 0x0020
-#define FAIR_FLOW_CTRL 0x0010
-#define NO_EXC_COLLISION_DROP 0x0008
-#define SWITCH_HUGE_PACKET 0x0004
-#define SWITCH_LEGAL_PACKET 0x0002
-#define SWITCH_BUF_RESERVE 0x0001
-
-/* SGCR3 */
-#define KS8842_SGCR3_P 0x0406
-#define KS8842_SWITCH_CTRL_3_OFFSET KS8842_SGCR3_P
-
-#define BROADCAST_STORM_RATE_LO 0xFF00
-#define SWITCH_REPEATER 0x0080
-#define SWITCH_HALF_DUPLEX 0x0040
-#define SWITCH_FLOW_CTRL 0x0020
-#define SWITCH_10_MBIT 0x0010
-#define SWITCH_REPLACE_NULL_VID 0x0008
-#define BROADCAST_STORM_RATE_HI 0x0007
-
-#define BROADCAST_STORM_RATE 0x07FF
-
-/* SGCR4 */
-#define KS8842_SGCR4_P 0x0408
-
-/* SGCR5 */
-#define KS8842_SGCR5_P 0x040A
-#define KS8842_SWITCH_CTRL_5_OFFSET KS8842_SGCR5_P
-
-#define LED_MODE 0x8200
-#define LED_SPEED_DUPLEX_ACT 0x0000
-#define LED_SPEED_DUPLEX_LINK_ACT 0x8000
-#define LED_DUPLEX_10_100 0x0200
-
-/* SGCR6 */
-#define KS8842_SGCR6_P 0x0410
-#define KS8842_SWITCH_CTRL_6_OFFSET KS8842_SGCR6_P
-
-#define KS8842_PRIORITY_MASK 3
-#define KS8842_PRIORITY_SHIFT 2
-
-/* SGCR7 */
-#define KS8842_SGCR7_P 0x0412
-#define KS8842_SWITCH_CTRL_7_OFFSET KS8842_SGCR7_P
-
-#define SWITCH_UNK_DEF_PORT_ENABLE 0x0008
-#define SWITCH_UNK_DEF_PORT_3 0x0004
-#define SWITCH_UNK_DEF_PORT_2 0x0002
-#define SWITCH_UNK_DEF_PORT_1 0x0001
-
-/* MACAR1 */
-#define KS8842_MACAR1_P 0x0470
-#define KS8842_MACAR2_P 0x0472
-#define KS8842_MACAR3_P 0x0474
-#define KS8842_MAC_ADDR_1_OFFSET KS8842_MACAR1_P
-#define KS8842_MAC_ADDR_0_OFFSET (KS8842_MAC_ADDR_1_OFFSET + 1)
-#define KS8842_MAC_ADDR_3_OFFSET KS8842_MACAR2_P
-#define KS8842_MAC_ADDR_2_OFFSET (KS8842_MAC_ADDR_3_OFFSET + 1)
-#define KS8842_MAC_ADDR_5_OFFSET KS8842_MACAR3_P
-#define KS8842_MAC_ADDR_4_OFFSET (KS8842_MAC_ADDR_5_OFFSET + 1)
-
-/* TOSR1 */
-#define KS8842_TOSR1_P 0x0480
-#define KS8842_TOSR2_P 0x0482
-#define KS8842_TOSR3_P 0x0484
-#define KS8842_TOSR4_P 0x0486
-#define KS8842_TOSR5_P 0x0488
-#define KS8842_TOSR6_P 0x048A
-#define KS8842_TOSR7_P 0x0490
-#define KS8842_TOSR8_P 0x0492
-#define KS8842_TOS_1_OFFSET KS8842_TOSR1_P
-#define KS8842_TOS_2_OFFSET KS8842_TOSR2_P
-#define KS8842_TOS_3_OFFSET KS8842_TOSR3_P
-#define KS8842_TOS_4_OFFSET KS8842_TOSR4_P
-#define KS8842_TOS_5_OFFSET KS8842_TOSR5_P
-#define KS8842_TOS_6_OFFSET KS8842_TOSR6_P
-
-#define KS8842_TOS_7_OFFSET KS8842_TOSR7_P
-#define KS8842_TOS_8_OFFSET KS8842_TOSR8_P
-
-/* P1CR1 */
-#define KS8842_P1CR1_P 0x0500
-#define KS8842_P1CR2_P 0x0502
-#define KS8842_P1VIDR_P 0x0504
-#define KS8842_P1CR3_P 0x0506
-#define KS8842_P1IRCR_P 0x0508
-#define KS8842_P1ERCR_P 0x050A
-#define KS884X_P1SCSLMD_P 0x0510
-#define KS884X_P1CR4_P 0x0512
-#define KS884X_P1SR_P 0x0514
-
-/* P2CR1 */
-#define KS8842_P2CR1_P 0x0520
-#define KS8842_P2CR2_P 0x0522
-#define KS8842_P2VIDR_P 0x0524
-#define KS8842_P2CR3_P 0x0526
-#define KS8842_P2IRCR_P 0x0528
-#define KS8842_P2ERCR_P 0x052A
-#define KS884X_P2SCSLMD_P 0x0530
-#define KS884X_P2CR4_P 0x0532
-#define KS884X_P2SR_P 0x0534
-
-/* P3CR1 */
-#define KS8842_P3CR1_P 0x0540
-#define KS8842_P3CR2_P 0x0542
-#define KS8842_P3VIDR_P 0x0544
-#define KS8842_P3CR3_P 0x0546
-#define KS8842_P3IRCR_P 0x0548
-#define KS8842_P3ERCR_P 0x054A
-
-#define KS8842_PORT_1_CTRL_1 KS8842_P1CR1_P
-#define KS8842_PORT_2_CTRL_1 KS8842_P2CR1_P
-#define KS8842_PORT_3_CTRL_1 KS8842_P3CR1_P
-
-#define PORT_CTRL_ADDR(port, addr) \
- (addr = KS8842_PORT_1_CTRL_1 + (port) * \
- (KS8842_PORT_2_CTRL_1 - KS8842_PORT_1_CTRL_1))
-
-#define KS8842_PORT_CTRL_1_OFFSET 0x00
-
-#define PORT_BROADCAST_STORM 0x0080
-#define PORT_DIFFSERV_ENABLE 0x0040
-#define PORT_802_1P_ENABLE 0x0020
-#define PORT_BASED_PRIORITY_MASK 0x0018
-#define PORT_BASED_PRIORITY_BASE 0x0003
-#define PORT_BASED_PRIORITY_SHIFT 3
-#define PORT_BASED_PRIORITY_0 0x0000
-#define PORT_BASED_PRIORITY_1 0x0008
-#define PORT_BASED_PRIORITY_2 0x0010
-#define PORT_BASED_PRIORITY_3 0x0018
-#define PORT_INSERT_TAG 0x0004
-#define PORT_REMOVE_TAG 0x0002
-#define PORT_PRIO_QUEUE_ENABLE 0x0001
-
-#define KS8842_PORT_CTRL_2_OFFSET 0x02
-
-#define PORT_INGRESS_VLAN_FILTER 0x4000
-#define PORT_DISCARD_NON_VID 0x2000
-#define PORT_FORCE_FLOW_CTRL 0x1000
-#define PORT_BACK_PRESSURE 0x0800
-#define PORT_TX_ENABLE 0x0400
-#define PORT_RX_ENABLE 0x0200
-#define PORT_LEARN_DISABLE 0x0100
-#define PORT_MIRROR_SNIFFER 0x0080
-#define PORT_MIRROR_RX 0x0040
-#define PORT_MIRROR_TX 0x0020
-#define PORT_USER_PRIORITY_CEILING 0x0008
-#define PORT_VLAN_MEMBERSHIP 0x0007
-
-#define KS8842_PORT_CTRL_VID_OFFSET 0x04
-
-#define PORT_DEFAULT_VID 0x0001
-
-#define KS8842_PORT_CTRL_3_OFFSET 0x06
-
-#define PORT_INGRESS_LIMIT_MODE 0x000C
-#define PORT_INGRESS_ALL 0x0000
-#define PORT_INGRESS_UNICAST 0x0004
-#define PORT_INGRESS_MULTICAST 0x0008
-#define PORT_INGRESS_BROADCAST 0x000C
-#define PORT_COUNT_IFG 0x0002
-#define PORT_COUNT_PREAMBLE 0x0001
-
-#define KS8842_PORT_IN_RATE_OFFSET 0x08
-#define KS8842_PORT_OUT_RATE_OFFSET 0x0A
-
-#define PORT_PRIORITY_RATE 0x0F
-#define PORT_PRIORITY_RATE_SHIFT 4
-
-#define KS884X_PORT_LINK_MD 0x10
-
-#define PORT_CABLE_10M_SHORT 0x8000
-#define PORT_CABLE_DIAG_RESULT 0x6000
-#define PORT_CABLE_STAT_NORMAL 0x0000
-#define PORT_CABLE_STAT_OPEN 0x2000
-#define PORT_CABLE_STAT_SHORT 0x4000
-#define PORT_CABLE_STAT_FAILED 0x6000
-#define PORT_START_CABLE_DIAG 0x1000
-#define PORT_FORCE_LINK 0x0800
-#define PORT_POWER_SAVING_DISABLE 0x0400
-#define PORT_PHY_REMOTE_LOOPBACK 0x0200
-#define PORT_CABLE_FAULT_COUNTER 0x01FF
-
-#define KS884X_PORT_CTRL_4_OFFSET 0x12
-
-#define PORT_LED_OFF 0x8000
-#define PORT_TX_DISABLE 0x4000
-#define PORT_AUTO_NEG_RESTART 0x2000
-#define PORT_REMOTE_FAULT_DISABLE 0x1000
-#define PORT_POWER_DOWN 0x0800
-#define PORT_AUTO_MDIX_DISABLE 0x0400
-#define PORT_FORCE_MDIX 0x0200
-#define PORT_LOOPBACK 0x0100
-#define PORT_AUTO_NEG_ENABLE 0x0080
-#define PORT_FORCE_100_MBIT 0x0040
-#define PORT_FORCE_FULL_DUPLEX 0x0020
-#define PORT_AUTO_NEG_SYM_PAUSE 0x0010
-#define PORT_AUTO_NEG_100BTX_FD 0x0008
-#define PORT_AUTO_NEG_100BTX 0x0004
-#define PORT_AUTO_NEG_10BT_FD 0x0002
-#define PORT_AUTO_NEG_10BT 0x0001
-
-#define KS884X_PORT_STATUS_OFFSET 0x14
-
-#define PORT_HP_MDIX 0x8000
-#define PORT_REVERSED_POLARITY 0x2000
-#define PORT_RX_FLOW_CTRL 0x0800
-#define PORT_TX_FLOW_CTRL 0x1000
-#define PORT_STATUS_SPEED_100MBIT 0x0400
-#define PORT_STATUS_FULL_DUPLEX 0x0200
-#define PORT_REMOTE_FAULT 0x0100
-#define PORT_MDIX_STATUS 0x0080
-#define PORT_AUTO_NEG_COMPLETE 0x0040
-#define PORT_STATUS_LINK_GOOD 0x0020
-#define PORT_REMOTE_SYM_PAUSE 0x0010
-#define PORT_REMOTE_100BTX_FD 0x0008
-#define PORT_REMOTE_100BTX 0x0004
-#define PORT_REMOTE_10BT_FD 0x0002
-#define PORT_REMOTE_10BT 0x0001
-
-/*
-#define STATIC_MAC_TABLE_ADDR 00-0000FFFF-FFFFFFFF
-#define STATIC_MAC_TABLE_FWD_PORTS 00-00070000-00000000
-#define STATIC_MAC_TABLE_VALID 00-00080000-00000000
-#define STATIC_MAC_TABLE_OVERRIDE 00-00100000-00000000
-#define STATIC_MAC_TABLE_USE_FID 00-00200000-00000000
-#define STATIC_MAC_TABLE_FID 00-03C00000-00000000
-*/
-
-#define STATIC_MAC_TABLE_ADDR 0x0000FFFF
-#define STATIC_MAC_TABLE_FWD_PORTS 0x00070000
-#define STATIC_MAC_TABLE_VALID 0x00080000
-#define STATIC_MAC_TABLE_OVERRIDE 0x00100000
-#define STATIC_MAC_TABLE_USE_FID 0x00200000
-#define STATIC_MAC_TABLE_FID 0x03C00000
-
-#define STATIC_MAC_FWD_PORTS_SHIFT 16
-#define STATIC_MAC_FID_SHIFT 22
-
-/*
-#define VLAN_TABLE_VID 00-00000000-00000FFF
-#define VLAN_TABLE_FID 00-00000000-0000F000
-#define VLAN_TABLE_MEMBERSHIP 00-00000000-00070000
-#define VLAN_TABLE_VALID 00-00000000-00080000
-*/
-
-#define VLAN_TABLE_VID 0x00000FFF
-#define VLAN_TABLE_FID 0x0000F000
-#define VLAN_TABLE_MEMBERSHIP 0x00070000
-#define VLAN_TABLE_VALID 0x00080000
-
-#define VLAN_TABLE_FID_SHIFT 12
-#define VLAN_TABLE_MEMBERSHIP_SHIFT 16
-
-/*
-#define DYNAMIC_MAC_TABLE_ADDR 00-0000FFFF-FFFFFFFF
-#define DYNAMIC_MAC_TABLE_FID 00-000F0000-00000000
-#define DYNAMIC_MAC_TABLE_SRC_PORT 00-00300000-00000000
-#define DYNAMIC_MAC_TABLE_TIMESTAMP 00-00C00000-00000000
-#define DYNAMIC_MAC_TABLE_ENTRIES 03-FF000000-00000000
-#define DYNAMIC_MAC_TABLE_MAC_EMPTY 04-00000000-00000000
-#define DYNAMIC_MAC_TABLE_RESERVED 78-00000000-00000000
-#define DYNAMIC_MAC_TABLE_NOT_READY 80-00000000-00000000
-*/
-
-#define DYNAMIC_MAC_TABLE_ADDR 0x0000FFFF
-#define DYNAMIC_MAC_TABLE_FID 0x000F0000
-#define DYNAMIC_MAC_TABLE_SRC_PORT 0x00300000
-#define DYNAMIC_MAC_TABLE_TIMESTAMP 0x00C00000
-#define DYNAMIC_MAC_TABLE_ENTRIES 0xFF000000
-
-#define DYNAMIC_MAC_TABLE_ENTRIES_H 0x03
-#define DYNAMIC_MAC_TABLE_MAC_EMPTY 0x04
-#define DYNAMIC_MAC_TABLE_RESERVED 0x78
-#define DYNAMIC_MAC_TABLE_NOT_READY 0x80
-
-#define DYNAMIC_MAC_FID_SHIFT 16
-#define DYNAMIC_MAC_SRC_PORT_SHIFT 20
-#define DYNAMIC_MAC_TIMESTAMP_SHIFT 22
-#define DYNAMIC_MAC_ENTRIES_SHIFT 24
-#define DYNAMIC_MAC_ENTRIES_H_SHIFT 8
-
-/*
-#define MIB_COUNTER_VALUE 00-00000000-3FFFFFFF
-#define MIB_COUNTER_VALID 00-00000000-40000000
-#define MIB_COUNTER_OVERFLOW 00-00000000-80000000
-*/
-
-#define MIB_COUNTER_VALUE 0x3FFFFFFF
-#define MIB_COUNTER_VALID 0x40000000
-#define MIB_COUNTER_OVERFLOW 0x80000000
-
-#define MIB_PACKET_DROPPED 0x0000FFFF
-
-#define KS_MIB_PACKET_DROPPED_TX_0 0x100
-#define KS_MIB_PACKET_DROPPED_TX_1 0x101
-#define KS_MIB_PACKET_DROPPED_TX 0x102
-#define KS_MIB_PACKET_DROPPED_RX_0 0x103
-#define KS_MIB_PACKET_DROPPED_RX_1 0x104
-#define KS_MIB_PACKET_DROPPED_RX 0x105
-
-/* Change default LED mode. */
-#define SET_DEFAULT_LED LED_SPEED_DUPLEX_ACT
-
-#define MAC_ADDR_LEN 6
-#define MAC_ADDR_ORDER(i) (MAC_ADDR_LEN - 1 - (i))
-
-#define MAX_ETHERNET_BODY_SIZE 1500
-#define ETHERNET_HEADER_SIZE 14
-
-#define MAX_ETHERNET_PACKET_SIZE \
- (MAX_ETHERNET_BODY_SIZE + ETHERNET_HEADER_SIZE)
-
-#define REGULAR_RX_BUF_SIZE (MAX_ETHERNET_PACKET_SIZE + 4)
-#define MAX_RX_BUF_SIZE (1912 + 4)
-
-#define ADDITIONAL_ENTRIES 16
-#define MAX_MULTICAST_LIST 32
-
-#define HW_MULTICAST_SIZE 8
-
-#define HW_TO_DEV_PORT(port) (port - 1)
-
-enum {
- media_connected,
- media_disconnected
-};
-
-enum {
- OID_COUNTER_UNKOWN,
-
- OID_COUNTER_FIRST,
-
- /* total transmit errors */
- OID_COUNTER_XMIT_ERROR,
-
- /* total receive errors */
- OID_COUNTER_RCV_ERROR,
-
- OID_COUNTER_LAST
-};
-
-/*
- * Hardware descriptor definitions
- */
-
-#define DESC_ALIGNMENT 16
-#define BUFFER_ALIGNMENT 8
-
-#define NUM_OF_RX_DESC 64
-#define NUM_OF_TX_DESC 64
-
-#define KS_DESC_RX_FRAME_LEN 0x000007FF
-#define KS_DESC_RX_FRAME_TYPE 0x00008000
-#define KS_DESC_RX_ERROR_CRC 0x00010000
-#define KS_DESC_RX_ERROR_RUNT 0x00020000
-#define KS_DESC_RX_ERROR_TOO_LONG 0x00040000
-#define KS_DESC_RX_ERROR_PHY 0x00080000
-#define KS884X_DESC_RX_PORT_MASK 0x00300000
-#define KS_DESC_RX_MULTICAST 0x01000000
-#define KS_DESC_RX_ERROR 0x02000000
-#define KS_DESC_RX_ERROR_CSUM_UDP 0x04000000
-#define KS_DESC_RX_ERROR_CSUM_TCP 0x08000000
-#define KS_DESC_RX_ERROR_CSUM_IP 0x10000000
-#define KS_DESC_RX_LAST 0x20000000
-#define KS_DESC_RX_FIRST 0x40000000
-#define KS_DESC_RX_ERROR_COND \
- (KS_DESC_RX_ERROR_CRC | \
- KS_DESC_RX_ERROR_RUNT | \
- KS_DESC_RX_ERROR_PHY | \
- KS_DESC_RX_ERROR_TOO_LONG)
-
-#define KS_DESC_HW_OWNED 0x80000000
-
-#define KS_DESC_BUF_SIZE 0x000007FF
-#define KS884X_DESC_TX_PORT_MASK 0x00300000
-#define KS_DESC_END_OF_RING 0x02000000
-#define KS_DESC_TX_CSUM_GEN_UDP 0x04000000
-#define KS_DESC_TX_CSUM_GEN_TCP 0x08000000
-#define KS_DESC_TX_CSUM_GEN_IP 0x10000000
-#define KS_DESC_TX_LAST 0x20000000
-#define KS_DESC_TX_FIRST 0x40000000
-#define KS_DESC_TX_INTERRUPT 0x80000000
-
-#define KS_DESC_PORT_SHIFT 20
-
-#define KS_DESC_RX_MASK (KS_DESC_BUF_SIZE)
-
-#define KS_DESC_TX_MASK \
- (KS_DESC_TX_INTERRUPT | \
- KS_DESC_TX_FIRST | \
- KS_DESC_TX_LAST | \
- KS_DESC_TX_CSUM_GEN_IP | \
- KS_DESC_TX_CSUM_GEN_TCP | \
- KS_DESC_TX_CSUM_GEN_UDP | \
- KS_DESC_BUF_SIZE)
-
-struct ksz_desc_rx_stat {
-#ifdef __BIG_ENDIAN_BITFIELD
- u32 hw_owned:1;
- u32 first_desc:1;
- u32 last_desc:1;
- u32 csum_err_ip:1;
- u32 csum_err_tcp:1;
- u32 csum_err_udp:1;
- u32 error:1;
- u32 multicast:1;
- u32 src_port:4;
- u32 err_phy:1;
- u32 err_too_long:1;
- u32 err_runt:1;
- u32 err_crc:1;
- u32 frame_type:1;
- u32 reserved1:4;
- u32 frame_len:11;
-#else
- u32 frame_len:11;
- u32 reserved1:4;
- u32 frame_type:1;
- u32 err_crc:1;
- u32 err_runt:1;
- u32 err_too_long:1;
- u32 err_phy:1;
- u32 src_port:4;
- u32 multicast:1;
- u32 error:1;
- u32 csum_err_udp:1;
- u32 csum_err_tcp:1;
- u32 csum_err_ip:1;
- u32 last_desc:1;
- u32 first_desc:1;
- u32 hw_owned:1;
-#endif
-};
-
-struct ksz_desc_tx_stat {
-#ifdef __BIG_ENDIAN_BITFIELD
- u32 hw_owned:1;
- u32 reserved1:31;
-#else
- u32 reserved1:31;
- u32 hw_owned:1;
-#endif
-};
-
-struct ksz_desc_rx_buf {
-#ifdef __BIG_ENDIAN_BITFIELD
- u32 reserved4:6;
- u32 end_of_ring:1;
- u32 reserved3:14;
- u32 buf_size:11;
-#else
- u32 buf_size:11;
- u32 reserved3:14;
- u32 end_of_ring:1;
- u32 reserved4:6;
-#endif
-};
-
-struct ksz_desc_tx_buf {
-#ifdef __BIG_ENDIAN_BITFIELD
- u32 intr:1;
- u32 first_seg:1;
- u32 last_seg:1;
- u32 csum_gen_ip:1;
- u32 csum_gen_tcp:1;
- u32 csum_gen_udp:1;
- u32 end_of_ring:1;
- u32 reserved4:1;
- u32 dest_port:4;
- u32 reserved3:9;
- u32 buf_size:11;
-#else
- u32 buf_size:11;
- u32 reserved3:9;
- u32 dest_port:4;
- u32 reserved4:1;
- u32 end_of_ring:1;
- u32 csum_gen_udp:1;
- u32 csum_gen_tcp:1;
- u32 csum_gen_ip:1;
- u32 last_seg:1;
- u32 first_seg:1;
- u32 intr:1;
-#endif
-};
-
-union desc_stat {
- struct ksz_desc_rx_stat rx;
- struct ksz_desc_tx_stat tx;
- u32 data;
-};
-
-union desc_buf {
- struct ksz_desc_rx_buf rx;
- struct ksz_desc_tx_buf tx;
- u32 data;
-};
-
-/**
- * struct ksz_hw_desc - Hardware descriptor data structure
- * @ctrl: Descriptor control value.
- * @buf: Descriptor buffer value.
- * @addr: Physical address of memory buffer.
- * @next: Pointer to next hardware descriptor.
- */
-struct ksz_hw_desc {
- union desc_stat ctrl;
- union desc_buf buf;
- u32 addr;
- u32 next;
-};
-
-/**
- * struct ksz_sw_desc - Software descriptor data structure
- * @ctrl: Descriptor control value.
- * @buf: Descriptor buffer value.
- * @buf_size: Current buffers size value in hardware descriptor.
- */
-struct ksz_sw_desc {
- union desc_stat ctrl;
- union desc_buf buf;
- u32 buf_size;
-};
-
-/**
- * struct ksz_dma_buf - OS dependent DMA buffer data structure
- * @skb: Associated socket buffer.
- * @dma: Associated physical DMA address.
- * len: Actual len used.
- */
-struct ksz_dma_buf {
- struct sk_buff *skb;
- dma_addr_t dma;
- int len;
-};
-
-/**
- * struct ksz_desc - Descriptor structure
- * @phw: Hardware descriptor pointer to uncached physical memory.
- * @sw: Cached memory to hold hardware descriptor values for
- * manipulation.
- * @dma_buf: Operating system dependent data structure to hold physical
- * memory buffer allocation information.
- */
-struct ksz_desc {
- struct ksz_hw_desc *phw;
- struct ksz_sw_desc sw;
- struct ksz_dma_buf dma_buf;
-};
-
-#define DMA_BUFFER(desc) ((struct ksz_dma_buf *)(&(desc)->dma_buf))
-
-/**
- * struct ksz_desc_info - Descriptor information data structure
- * @ring: First descriptor in the ring.
- * @cur: Current descriptor being manipulated.
- * @ring_virt: First hardware descriptor in the ring.
- * @ring_phys: The physical address of the first descriptor of the ring.
- * @size: Size of hardware descriptor.
- * @alloc: Number of descriptors allocated.
- * @avail: Number of descriptors available for use.
- * @last: Index for last descriptor released to hardware.
- * @next: Index for next descriptor available for use.
- * @mask: Mask for index wrapping.
- */
-struct ksz_desc_info {
- struct ksz_desc *ring;
- struct ksz_desc *cur;
- struct ksz_hw_desc *ring_virt;
- u32 ring_phys;
- int size;
- int alloc;
- int avail;
- int last;
- int next;
- int mask;
-};
-
-/*
- * KSZ8842 switch definitions
- */
-
-enum {
- TABLE_STATIC_MAC = 0,
- TABLE_VLAN,
- TABLE_DYNAMIC_MAC,
- TABLE_MIB
-};
-
-#define LEARNED_MAC_TABLE_ENTRIES 1024
-#define STATIC_MAC_TABLE_ENTRIES 8
-
-/**
- * struct ksz_mac_table - Static MAC table data structure
- * @mac_addr: MAC address to filter.
- * @vid: VID value.
- * @fid: FID value.
- * @ports: Port membership.
- * @override: Override setting.
- * @use_fid: FID use setting.
- * @valid: Valid setting indicating the entry is being used.
- */
-struct ksz_mac_table {
- u8 mac_addr[MAC_ADDR_LEN];
- u16 vid;
- u8 fid;
- u8 ports;
- u8 override:1;
- u8 use_fid:1;
- u8 valid:1;
-};
-
-#define VLAN_TABLE_ENTRIES 16
-
-/**
- * struct ksz_vlan_table - VLAN table data structure
- * @vid: VID value.
- * @fid: FID value.
- * @member: Port membership.
- */
-struct ksz_vlan_table {
- u16 vid;
- u8 fid;
- u8 member;
-};
-
-#define DIFFSERV_ENTRIES 64
-#define PRIO_802_1P_ENTRIES 8
-#define PRIO_QUEUES 4
-
-#define SWITCH_PORT_NUM 2
-#define TOTAL_PORT_NUM (SWITCH_PORT_NUM + 1)
-#define HOST_MASK (1 << SWITCH_PORT_NUM)
-#define PORT_MASK 7
-
-#define MAIN_PORT 0
-#define OTHER_PORT 1
-#define HOST_PORT SWITCH_PORT_NUM
-
-#define PORT_COUNTER_NUM 0x20
-#define TOTAL_PORT_COUNTER_NUM (PORT_COUNTER_NUM + 2)
-
-#define MIB_COUNTER_RX_LO_PRIORITY 0x00
-#define MIB_COUNTER_RX_HI_PRIORITY 0x01
-#define MIB_COUNTER_RX_UNDERSIZE 0x02
-#define MIB_COUNTER_RX_FRAGMENT 0x03
-#define MIB_COUNTER_RX_OVERSIZE 0x04
-#define MIB_COUNTER_RX_JABBER 0x05
-#define MIB_COUNTER_RX_SYMBOL_ERR 0x06
-#define MIB_COUNTER_RX_CRC_ERR 0x07
-#define MIB_COUNTER_RX_ALIGNMENT_ERR 0x08
-#define MIB_COUNTER_RX_CTRL_8808 0x09
-#define MIB_COUNTER_RX_PAUSE 0x0A
-#define MIB_COUNTER_RX_BROADCAST 0x0B
-#define MIB_COUNTER_RX_MULTICAST 0x0C
-#define MIB_COUNTER_RX_UNICAST 0x0D
-#define MIB_COUNTER_RX_OCTET_64 0x0E
-#define MIB_COUNTER_RX_OCTET_65_127 0x0F
-#define MIB_COUNTER_RX_OCTET_128_255 0x10
-#define MIB_COUNTER_RX_OCTET_256_511 0x11
-#define MIB_COUNTER_RX_OCTET_512_1023 0x12
-#define MIB_COUNTER_RX_OCTET_1024_1522 0x13
-#define MIB_COUNTER_TX_LO_PRIORITY 0x14
-#define MIB_COUNTER_TX_HI_PRIORITY 0x15
-#define MIB_COUNTER_TX_LATE_COLLISION 0x16
-#define MIB_COUNTER_TX_PAUSE 0x17
-#define MIB_COUNTER_TX_BROADCAST 0x18
-#define MIB_COUNTER_TX_MULTICAST 0x19
-#define MIB_COUNTER_TX_UNICAST 0x1A
-#define MIB_COUNTER_TX_DEFERRED 0x1B
-#define MIB_COUNTER_TX_TOTAL_COLLISION 0x1C
-#define MIB_COUNTER_TX_EXCESS_COLLISION 0x1D
-#define MIB_COUNTER_TX_SINGLE_COLLISION 0x1E
-#define MIB_COUNTER_TX_MULTI_COLLISION 0x1F
-
-#define MIB_COUNTER_RX_DROPPED_PACKET 0x20
-#define MIB_COUNTER_TX_DROPPED_PACKET 0x21
-
-/**
- * struct ksz_port_mib - Port MIB data structure
- * @cnt_ptr: Current pointer to MIB counter index.
- * @link_down: Indication the link has just gone down.
- * @state: Connection status of the port.
- * @mib_start: The starting counter index. Some ports do not start at 0.
- * @counter: 64-bit MIB counter value.
- * @dropped: Temporary buffer to remember last read packet dropped values.
- *
- * MIB counters needs to be read periodically so that counters do not get
- * overflowed and give incorrect values. A right balance is needed to
- * satisfy this condition and not waste too much CPU time.
- *
- * It is pointless to read MIB counters when the port is disconnected. The
- * @state provides the connection status so that MIB counters are read only
- * when the port is connected. The @link_down indicates the port is just
- * disconnected so that all MIB counters are read one last time to update the
- * information.
- */
-struct ksz_port_mib {
- u8 cnt_ptr;
- u8 link_down;
- u8 state;
- u8 mib_start;
-
- u64 counter[TOTAL_PORT_COUNTER_NUM];
- u32 dropped[2];
-};
-
-/**
- * struct ksz_port_cfg - Port configuration data structure
- * @vid: VID value.
- * @member: Port membership.
- * @port_prio: Port priority.
- * @rx_rate: Receive priority rate.
- * @tx_rate: Transmit priority rate.
- * @stp_state: Current Spanning Tree Protocol state.
- */
-struct ksz_port_cfg {
- u16 vid;
- u8 member;
- u8 port_prio;
- u32 rx_rate[PRIO_QUEUES];
- u32 tx_rate[PRIO_QUEUES];
- int stp_state;
-};
-
-/**
- * struct ksz_switch - KSZ8842 switch data structure
- * @mac_table: MAC table entries information.
- * @vlan_table: VLAN table entries information.
- * @port_cfg: Port configuration information.
- * @diffserv: DiffServ priority settings. Possible values from 6-bit of ToS
- * (bit7 ~ bit2) field.
- * @p_802_1p: 802.1P priority settings. Possible values from 3-bit of 802.1p
- * Tag priority field.
- * @br_addr: Bridge address. Used for STP.
- * @other_addr: Other MAC address. Used for multiple network device mode.
- * @broad_per: Broadcast storm percentage.
- * @member: Current port membership. Used for STP.
- */
-struct ksz_switch {
- struct ksz_mac_table mac_table[STATIC_MAC_TABLE_ENTRIES];
- struct ksz_vlan_table vlan_table[VLAN_TABLE_ENTRIES];
- struct ksz_port_cfg port_cfg[TOTAL_PORT_NUM];
-
- u8 diffserv[DIFFSERV_ENTRIES];
- u8 p_802_1p[PRIO_802_1P_ENTRIES];
-
- u8 br_addr[MAC_ADDR_LEN];
- u8 other_addr[MAC_ADDR_LEN];
-
- u8 broad_per;
- u8 member;
-};
-
-#define TX_RATE_UNIT 10000
-
-/**
- * struct ksz_port_info - Port information data structure
- * @state: Connection status of the port.
- * @tx_rate: Transmit rate divided by 10000 to get Mbit.
- * @duplex: Duplex mode.
- * @advertised: Advertised auto-negotiation setting. Used to determine link.
- * @partner: Auto-negotiation partner setting. Used to determine link.
- * @port_id: Port index to access actual hardware register.
- * @pdev: Pointer to OS dependent network device.
- */
-struct ksz_port_info {
- uint state;
- uint tx_rate;
- u8 duplex;
- u8 advertised;
- u8 partner;
- u8 port_id;
- void *pdev;
-};
-
-#define MAX_TX_HELD_SIZE 52000
-
-/* Hardware features and bug fixes. */
-#define LINK_INT_WORKING (1 << 0)
-#define SMALL_PACKET_TX_BUG (1 << 1)
-#define HALF_DUPLEX_SIGNAL_BUG (1 << 2)
-#define RX_HUGE_FRAME (1 << 4)
-#define STP_SUPPORT (1 << 8)
-
-/* Software overrides. */
-#define PAUSE_FLOW_CTRL (1 << 0)
-#define FAST_AGING (1 << 1)
-
-/**
- * struct ksz_hw - KSZ884X hardware data structure
- * @io: Virtual address assigned.
- * @ksz_switch: Pointer to KSZ8842 switch.
- * @port_info: Port information.
- * @port_mib: Port MIB information.
- * @dev_count: Number of network devices this hardware supports.
- * @dst_ports: Destination ports in switch for transmission.
- * @id: Hardware ID. Used for display only.
- * @mib_cnt: Number of MIB counters this hardware has.
- * @mib_port_cnt: Number of ports with MIB counters.
- * @tx_cfg: Cached transmit control settings.
- * @rx_cfg: Cached receive control settings.
- * @intr_mask: Current interrupt mask.
- * @intr_set: Current interrup set.
- * @intr_blocked: Interrupt blocked.
- * @rx_desc_info: Receive descriptor information.
- * @tx_desc_info: Transmit descriptor information.
- * @tx_int_cnt: Transmit interrupt count. Used for TX optimization.
- * @tx_int_mask: Transmit interrupt mask. Used for TX optimization.
- * @tx_size: Transmit data size. Used for TX optimization.
- * The maximum is defined by MAX_TX_HELD_SIZE.
- * @perm_addr: Permanent MAC address.
- * @override_addr: Overrided MAC address.
- * @address: Additional MAC address entries.
- * @addr_list_size: Additional MAC address list size.
- * @mac_override: Indication of MAC address overrided.
- * @promiscuous: Counter to keep track of promiscuous mode set.
- * @all_multi: Counter to keep track of all multicast mode set.
- * @multi_list: Multicast address entries.
- * @multi_bits: Cached multicast hash table settings.
- * @multi_list_size: Multicast address list size.
- * @enabled: Indication of hardware enabled.
- * @rx_stop: Indication of receive process stop.
- * @features: Hardware features to enable.
- * @overrides: Hardware features to override.
- * @parent: Pointer to parent, network device private structure.
- */
-struct ksz_hw {
- void __iomem *io;
-
- struct ksz_switch *ksz_switch;
- struct ksz_port_info port_info[SWITCH_PORT_NUM];
- struct ksz_port_mib port_mib[TOTAL_PORT_NUM];
- int dev_count;
- int dst_ports;
- int id;
- int mib_cnt;
- int mib_port_cnt;
-
- u32 tx_cfg;
- u32 rx_cfg;
- u32 intr_mask;
- u32 intr_set;
- uint intr_blocked;
-
- struct ksz_desc_info rx_desc_info;
- struct ksz_desc_info tx_desc_info;
-
- int tx_int_cnt;
- int tx_int_mask;
- int tx_size;
-
- u8 perm_addr[MAC_ADDR_LEN];
- u8 override_addr[MAC_ADDR_LEN];
- u8 address[ADDITIONAL_ENTRIES][MAC_ADDR_LEN];
- u8 addr_list_size;
- u8 mac_override;
- u8 promiscuous;
- u8 all_multi;
- u8 multi_list[MAX_MULTICAST_LIST][MAC_ADDR_LEN];
- u8 multi_bits[HW_MULTICAST_SIZE];
- u8 multi_list_size;
-
- u8 enabled;
- u8 rx_stop;
- u8 reserved2[1];
-
- uint features;
- uint overrides;
-
- void *parent;
-};
-
-enum {
- PHY_NO_FLOW_CTRL,
- PHY_FLOW_CTRL,
- PHY_TX_ONLY,
- PHY_RX_ONLY
-};
-
-/**
- * struct ksz_port - Virtual port data structure
- * @duplex: Duplex mode setting. 1 for half duplex, 2 for full
- * duplex, and 0 for auto, which normally results in full
- * duplex.
- * @speed: Speed setting. 10 for 10 Mbit, 100 for 100 Mbit, and
- * 0 for auto, which normally results in 100 Mbit.
- * @force_link: Force link setting. 0 for auto-negotiation, and 1 for
- * force.
- * @flow_ctrl: Flow control setting. PHY_NO_FLOW_CTRL for no flow
- * control, and PHY_FLOW_CTRL for flow control.
- * PHY_TX_ONLY and PHY_RX_ONLY are not supported for 100
- * Mbit PHY.
- * @first_port: Index of first port this port supports.
- * @mib_port_cnt: Number of ports with MIB counters.
- * @port_cnt: Number of ports this port supports.
- * @counter: Port statistics counter.
- * @hw: Pointer to hardware structure.
- * @linked: Pointer to port information linked to this port.
- */
-struct ksz_port {
- u8 duplex;
- u8 speed;
- u8 force_link;
- u8 flow_ctrl;
-
- int first_port;
- int mib_port_cnt;
- int port_cnt;
- u64 counter[OID_COUNTER_LAST];
-
- struct ksz_hw *hw;
- struct ksz_port_info *linked;
-};
-
-/**
- * struct ksz_timer_info - Timer information data structure
- * @timer: Kernel timer.
- * @cnt: Running timer counter.
- * @max: Number of times to run timer; -1 for infinity.
- * @period: Timer period in jiffies.
- */
-struct ksz_timer_info {
- struct timer_list timer;
- int cnt;
- int max;
- int period;
-};
-
-/**
- * struct ksz_shared_mem - OS dependent shared memory data structure
- * @dma_addr: Physical DMA address allocated.
- * @alloc_size: Allocation size.
- * @phys: Actual physical address used.
- * @alloc_virt: Virtual address allocated.
- * @virt: Actual virtual address used.
- */
-struct ksz_shared_mem {
- dma_addr_t dma_addr;
- uint alloc_size;
- uint phys;
- u8 *alloc_virt;
- u8 *virt;
-};
-
-/**
- * struct ksz_counter_info - OS dependent counter information data structure
- * @counter: Wait queue to wakeup after counters are read.
- * @time: Next time in jiffies to read counter.
- * @read: Indication of counters read in full or not.
- */
-struct ksz_counter_info {
- wait_queue_head_t counter;
- unsigned long time;
- int read;
-};
-
-/**
- * struct dev_info - Network device information data structure
- * @dev: Pointer to network device.
- * @pdev: Pointer to PCI device.
- * @hw: Hardware structure.
- * @desc_pool: Physical memory used for descriptor pool.
- * @hwlock: Spinlock to prevent hardware from accessing.
- * @lock: Mutex lock to prevent device from accessing.
- * @dev_rcv: Receive process function used.
- * @last_skb: Socket buffer allocated for descriptor rx fragments.
- * @skb_index: Buffer index for receiving fragments.
- * @skb_len: Buffer length for receiving fragments.
- * @mib_read: Workqueue to read MIB counters.
- * @mib_timer_info: Timer to read MIB counters.
- * @counter: Used for MIB reading.
- * @mtu: Current MTU used. The default is REGULAR_RX_BUF_SIZE;
- * the maximum is MAX_RX_BUF_SIZE.
- * @opened: Counter to keep track of device open.
- * @rx_tasklet: Receive processing tasklet.
- * @tx_tasklet: Transmit processing tasklet.
- * @wol_enable: Wake-on-LAN enable set by ethtool.
- * @wol_support: Wake-on-LAN support used by ethtool.
- * @pme_wait: Used for KSZ8841 power management.
- */
-struct dev_info {
- struct net_device *dev;
- struct pci_dev *pdev;
-
- struct ksz_hw hw;
- struct ksz_shared_mem desc_pool;
-
- spinlock_t hwlock;
- struct mutex lock;
-
- int (*dev_rcv)(struct dev_info *);
-
- struct sk_buff *last_skb;
- int skb_index;
- int skb_len;
-
- struct work_struct mib_read;
- struct ksz_timer_info mib_timer_info;
- struct ksz_counter_info counter[TOTAL_PORT_NUM];
-
- int mtu;
- int opened;
-
- struct tasklet_struct rx_tasklet;
- struct tasklet_struct tx_tasklet;
-
- int wol_enable;
- int wol_support;
- unsigned long pme_wait;
-};
-
-/**
- * struct dev_priv - Network device private data structure
- * @adapter: Adapter device information.
- * @port: Port information.
- * @monitor_time_info: Timer to monitor ports.
- * @proc_sem: Semaphore for proc accessing.
- * @id: Device ID.
- * @mii_if: MII interface information.
- * @advertising: Temporary variable to store advertised settings.
- * @msg_enable: The message flags controlling driver output.
- * @media_state: The connection status of the device.
- * @multicast: The all multicast state of the device.
- * @promiscuous: The promiscuous state of the device.
- */
-struct dev_priv {
- struct dev_info *adapter;
- struct ksz_port port;
- struct ksz_timer_info monitor_timer_info;
-
- struct semaphore proc_sem;
- int id;
-
- struct mii_if_info mii_if;
- u32 advertising;
-
- u32 msg_enable;
- int media_state;
- int multicast;
- int promiscuous;
-};
-
-#define DRV_NAME "KSZ884X PCI"
-#define DEVICE_NAME "KSZ884x PCI"
-#define DRV_VERSION "1.0.0"
-#define DRV_RELDATE "Feb 8, 2010"
-
-static char version[] __devinitdata =
- "Micrel " DEVICE_NAME " " DRV_VERSION " (" DRV_RELDATE ")";
-
-static u8 DEFAULT_MAC_ADDRESS[] = { 0x00, 0x10, 0xA1, 0x88, 0x42, 0x01 };
-
-/*
- * Interrupt processing primary routines
- */
-
-static inline void hw_ack_intr(struct ksz_hw *hw, uint interrupt)
-{
- writel(interrupt, hw->io + KS884X_INTERRUPTS_STATUS);
-}
-
-static inline void hw_dis_intr(struct ksz_hw *hw)
-{
- hw->intr_blocked = hw->intr_mask;
- writel(0, hw->io + KS884X_INTERRUPTS_ENABLE);
- hw->intr_set = readl(hw->io + KS884X_INTERRUPTS_ENABLE);
-}
-
-static inline void hw_set_intr(struct ksz_hw *hw, uint interrupt)
-{
- hw->intr_set = interrupt;
- writel(interrupt, hw->io + KS884X_INTERRUPTS_ENABLE);
-}
-
-static inline void hw_ena_intr(struct ksz_hw *hw)
-{
- hw->intr_blocked = 0;
- hw_set_intr(hw, hw->intr_mask);
-}
-
-static inline void hw_dis_intr_bit(struct ksz_hw *hw, uint bit)
-{
- hw->intr_mask &= ~(bit);
-}
-
-static inline void hw_turn_off_intr(struct ksz_hw *hw, uint interrupt)
-{
- u32 read_intr;
-
- read_intr = readl(hw->io + KS884X_INTERRUPTS_ENABLE);
- hw->intr_set = read_intr & ~interrupt;
- writel(hw->intr_set, hw->io + KS884X_INTERRUPTS_ENABLE);
- hw_dis_intr_bit(hw, interrupt);
-}
-
-/**
- * hw_turn_on_intr - turn on specified interrupts
- * @hw: The hardware instance.
- * @bit: The interrupt bits to be on.
- *
- * This routine turns on the specified interrupts in the interrupt mask so that
- * those interrupts will be enabled.
- */
-static void hw_turn_on_intr(struct ksz_hw *hw, u32 bit)
-{
- hw->intr_mask |= bit;
-
- if (!hw->intr_blocked)
- hw_set_intr(hw, hw->intr_mask);
-}
-
-static inline void hw_ena_intr_bit(struct ksz_hw *hw, uint interrupt)
-{
- u32 read_intr;
-
- read_intr = readl(hw->io + KS884X_INTERRUPTS_ENABLE);
- hw->intr_set = read_intr | interrupt;
- writel(hw->intr_set, hw->io + KS884X_INTERRUPTS_ENABLE);
-}
-
-static inline void hw_read_intr(struct ksz_hw *hw, uint *status)
-{
- *status = readl(hw->io + KS884X_INTERRUPTS_STATUS);
- *status = *status & hw->intr_set;
-}
-
-static inline void hw_restore_intr(struct ksz_hw *hw, uint interrupt)
-{
- if (interrupt)
- hw_ena_intr(hw);
-}
-
-/**
- * hw_block_intr - block hardware interrupts
- *
- * This function blocks all interrupts of the hardware and returns the current
- * interrupt enable mask so that interrupts can be restored later.
- *
- * Return the current interrupt enable mask.
- */
-static uint hw_block_intr(struct ksz_hw *hw)
-{
- uint interrupt = 0;
-
- if (!hw->intr_blocked) {
- hw_dis_intr(hw);
- interrupt = hw->intr_blocked;
- }
- return interrupt;
-}
-
-/*
- * Hardware descriptor routines
- */
-
-static inline void reset_desc(struct ksz_desc *desc, union desc_stat status)
-{
- status.rx.hw_owned = 0;
- desc->phw->ctrl.data = cpu_to_le32(status.data);
-}
-
-static inline void release_desc(struct ksz_desc *desc)
-{
- desc->sw.ctrl.tx.hw_owned = 1;
- if (desc->sw.buf_size != desc->sw.buf.data) {
- desc->sw.buf_size = desc->sw.buf.data;
- desc->phw->buf.data = cpu_to_le32(desc->sw.buf.data);
- }
- desc->phw->ctrl.data = cpu_to_le32(desc->sw.ctrl.data);
-}
-
-static void get_rx_pkt(struct ksz_desc_info *info, struct ksz_desc **desc)
-{
- *desc = &info->ring[info->last];
- info->last++;
- info->last &= info->mask;
- info->avail--;
- (*desc)->sw.buf.data &= ~KS_DESC_RX_MASK;
-}
-
-static inline void set_rx_buf(struct ksz_desc *desc, u32 addr)
-{
- desc->phw->addr = cpu_to_le32(addr);
-}
-
-static inline void set_rx_len(struct ksz_desc *desc, u32 len)
-{
- desc->sw.buf.rx.buf_size = len;
-}
-
-static inline void get_tx_pkt(struct ksz_desc_info *info,
- struct ksz_desc **desc)
-{
- *desc = &info->ring[info->next];
- info->next++;
- info->next &= info->mask;
- info->avail--;
- (*desc)->sw.buf.data &= ~KS_DESC_TX_MASK;
-}
-
-static inline void set_tx_buf(struct ksz_desc *desc, u32 addr)
-{
- desc->phw->addr = cpu_to_le32(addr);
-}
-
-static inline void set_tx_len(struct ksz_desc *desc, u32 len)
-{
- desc->sw.buf.tx.buf_size = len;
-}
-
-/* Switch functions */
-
-#define TABLE_READ 0x10
-#define TABLE_SEL_SHIFT 2
-
-#define HW_DELAY(hw, reg) \
- do { \
- u16 dummy; \
- dummy = readw(hw->io + reg); \
- } while (0)
-
-/**
- * sw_r_table - read 4 bytes of data from switch table
- * @hw: The hardware instance.
- * @table: The table selector.
- * @addr: The address of the table entry.
- * @data: Buffer to store the read data.
- *
- * This routine reads 4 bytes of data from the table of the switch.
- * Hardware interrupts are disabled to minimize corruption of read data.
- */
-static void sw_r_table(struct ksz_hw *hw, int table, u16 addr, u32 *data)
-{
- u16 ctrl_addr;
- uint interrupt;
-
- ctrl_addr = (((table << TABLE_SEL_SHIFT) | TABLE_READ) << 8) | addr;
-
- interrupt = hw_block_intr(hw);
-
- writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
- HW_DELAY(hw, KS884X_IACR_OFFSET);
- *data = readl(hw->io + KS884X_ACC_DATA_0_OFFSET);
-
- hw_restore_intr(hw, interrupt);
-}
-
-/**
- * sw_w_table_64 - write 8 bytes of data to the switch table
- * @hw: The hardware instance.
- * @table: The table selector.
- * @addr: The address of the table entry.
- * @data_hi: The high part of data to be written (bit63 ~ bit32).
- * @data_lo: The low part of data to be written (bit31 ~ bit0).
- *
- * This routine writes 8 bytes of data to the table of the switch.
- * Hardware interrupts are disabled to minimize corruption of written data.
- */
-static void sw_w_table_64(struct ksz_hw *hw, int table, u16 addr, u32 data_hi,
- u32 data_lo)
-{
- u16 ctrl_addr;
- uint interrupt;
-
- ctrl_addr = ((table << TABLE_SEL_SHIFT) << 8) | addr;
-
- interrupt = hw_block_intr(hw);
-
- writel(data_hi, hw->io + KS884X_ACC_DATA_4_OFFSET);
- writel(data_lo, hw->io + KS884X_ACC_DATA_0_OFFSET);
-
- writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
- HW_DELAY(hw, KS884X_IACR_OFFSET);
-
- hw_restore_intr(hw, interrupt);
-}
-
-/**
- * sw_w_sta_mac_table - write to the static MAC table
- * @hw: The hardware instance.
- * @addr: The address of the table entry.
- * @mac_addr: The MAC address.
- * @ports: The port members.
- * @override: The flag to override the port receive/transmit settings.
- * @valid: The flag to indicate entry is valid.
- * @use_fid: The flag to indicate the FID is valid.
- * @fid: The FID value.
- *
- * This routine writes an entry of the static MAC table of the switch. It
- * calls sw_w_table_64() to write the data.
- */
-static void sw_w_sta_mac_table(struct ksz_hw *hw, u16 addr, u8 *mac_addr,
- u8 ports, int override, int valid, int use_fid, u8 fid)
-{
- u32 data_hi;
- u32 data_lo;
-
- data_lo = ((u32) mac_addr[2] << 24) |
- ((u32) mac_addr[3] << 16) |
- ((u32) mac_addr[4] << 8) | mac_addr[5];
- data_hi = ((u32) mac_addr[0] << 8) | mac_addr[1];
- data_hi |= (u32) ports << STATIC_MAC_FWD_PORTS_SHIFT;
-
- if (override)
- data_hi |= STATIC_MAC_TABLE_OVERRIDE;
- if (use_fid) {
- data_hi |= STATIC_MAC_TABLE_USE_FID;
- data_hi |= (u32) fid << STATIC_MAC_FID_SHIFT;
- }
- if (valid)
- data_hi |= STATIC_MAC_TABLE_VALID;
-
- sw_w_table_64(hw, TABLE_STATIC_MAC, addr, data_hi, data_lo);
-}
-
-/**
- * sw_r_vlan_table - read from the VLAN table
- * @hw: The hardware instance.
- * @addr: The address of the table entry.
- * @vid: Buffer to store the VID.
- * @fid: Buffer to store the VID.
- * @member: Buffer to store the port membership.
- *
- * This function reads an entry of the VLAN table of the switch. It calls
- * sw_r_table() to get the data.
- *
- * Return 0 if the entry is valid; otherwise -1.
- */
-static int sw_r_vlan_table(struct ksz_hw *hw, u16 addr, u16 *vid, u8 *fid,
- u8 *member)
-{
- u32 data;
-
- sw_r_table(hw, TABLE_VLAN, addr, &data);
- if (data & VLAN_TABLE_VALID) {
- *vid = (u16)(data & VLAN_TABLE_VID);
- *fid = (u8)((data & VLAN_TABLE_FID) >> VLAN_TABLE_FID_SHIFT);
- *member = (u8)((data & VLAN_TABLE_MEMBERSHIP) >>
- VLAN_TABLE_MEMBERSHIP_SHIFT);
- return 0;
- }
- return -1;
-}
-
-/**
- * port_r_mib_cnt - read MIB counter
- * @hw: The hardware instance.
- * @port: The port index.
- * @addr: The address of the counter.
- * @cnt: Buffer to store the counter.
- *
- * This routine reads a MIB counter of the port.
- * Hardware interrupts are disabled to minimize corruption of read data.
- */
-static void port_r_mib_cnt(struct ksz_hw *hw, int port, u16 addr, u64 *cnt)
-{
- u32 data;
- u16 ctrl_addr;
- uint interrupt;
- int timeout;
-
- ctrl_addr = addr + PORT_COUNTER_NUM * port;
-
- interrupt = hw_block_intr(hw);
-
- ctrl_addr |= (((TABLE_MIB << TABLE_SEL_SHIFT) | TABLE_READ) << 8);
- writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
- HW_DELAY(hw, KS884X_IACR_OFFSET);
-
- for (timeout = 100; timeout > 0; timeout--) {
- data = readl(hw->io + KS884X_ACC_DATA_0_OFFSET);
-
- if (data & MIB_COUNTER_VALID) {
- if (data & MIB_COUNTER_OVERFLOW)
- *cnt += MIB_COUNTER_VALUE + 1;
- *cnt += data & MIB_COUNTER_VALUE;
- break;
- }
- }
-
- hw_restore_intr(hw, interrupt);
-}
-
-/**
- * port_r_mib_pkt - read dropped packet counts
- * @hw: The hardware instance.
- * @port: The port index.
- * @cnt: Buffer to store the receive and transmit dropped packet counts.
- *
- * This routine reads the dropped packet counts of the port.
- * Hardware interrupts are disabled to minimize corruption of read data.
- */
-static void port_r_mib_pkt(struct ksz_hw *hw, int port, u32 *last, u64 *cnt)
-{
- u32 cur;
- u32 data;
- u16 ctrl_addr;
- uint interrupt;
- int index;
-
- index = KS_MIB_PACKET_DROPPED_RX_0 + port;
- do {
- interrupt = hw_block_intr(hw);
-
- ctrl_addr = (u16) index;
- ctrl_addr |= (((TABLE_MIB << TABLE_SEL_SHIFT) | TABLE_READ)
- << 8);
- writew(ctrl_addr, hw->io + KS884X_IACR_OFFSET);
- HW_DELAY(hw, KS884X_IACR_OFFSET);
- data = readl(hw->io + KS884X_ACC_DATA_0_OFFSET);
-
- hw_restore_intr(hw, interrupt);
-
- data &= MIB_PACKET_DROPPED;
- cur = *last;
- if (data != cur) {
- *last = data;
- if (data < cur)
- data += MIB_PACKET_DROPPED + 1;
- data -= cur;
- *cnt += data;
- }
- ++last;
- ++cnt;
- index -= KS_MIB_PACKET_DROPPED_TX -
- KS_MIB_PACKET_DROPPED_TX_0 + 1;
- } while (index >= KS_MIB_PACKET_DROPPED_TX_0 + port);
-}
-
-/**
- * port_r_cnt - read MIB counters periodically
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine is used to read the counters of the port periodically to avoid
- * counter overflow. The hardware should be acquired first before calling this
- * routine.
- *
- * Return non-zero when not all counters not read.
- */
-static int port_r_cnt(struct ksz_hw *hw, int port)
-{
- struct ksz_port_mib *mib = &hw->port_mib[port];
-
- if (mib->mib_start < PORT_COUNTER_NUM)
- while (mib->cnt_ptr < PORT_COUNTER_NUM) {
- port_r_mib_cnt(hw, port, mib->cnt_ptr,
- &mib->counter[mib->cnt_ptr]);
- ++mib->cnt_ptr;
- }
- if (hw->mib_cnt > PORT_COUNTER_NUM)
- port_r_mib_pkt(hw, port, mib->dropped,
- &mib->counter[PORT_COUNTER_NUM]);
- mib->cnt_ptr = 0;
- return 0;
-}
-
-/**
- * port_init_cnt - initialize MIB counter values
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine is used to initialize all counters to zero if the hardware
- * cannot do it after reset.
- */
-static void port_init_cnt(struct ksz_hw *hw, int port)
-{
- struct ksz_port_mib *mib = &hw->port_mib[port];
-
- mib->cnt_ptr = 0;
- if (mib->mib_start < PORT_COUNTER_NUM)
- do {
- port_r_mib_cnt(hw, port, mib->cnt_ptr,
- &mib->counter[mib->cnt_ptr]);
- ++mib->cnt_ptr;
- } while (mib->cnt_ptr < PORT_COUNTER_NUM);
- if (hw->mib_cnt > PORT_COUNTER_NUM)
- port_r_mib_pkt(hw, port, mib->dropped,
- &mib->counter[PORT_COUNTER_NUM]);
- memset((void *) mib->counter, 0, sizeof(u64) * TOTAL_PORT_COUNTER_NUM);
- mib->cnt_ptr = 0;
-}
-
-/*
- * Port functions
- */
-
-/**
- * port_chk - check port register bits
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the port register.
- * @bits: The data bits to check.
- *
- * This function checks whether the specified bits of the port register are set
- * or not.
- *
- * Return 0 if the bits are not set.
- */
-static int port_chk(struct ksz_hw *hw, int port, int offset, u16 bits)
-{
- u32 addr;
- u16 data;
-
- PORT_CTRL_ADDR(port, addr);
- addr += offset;
- data = readw(hw->io + addr);
- return (data & bits) == bits;
-}
-
-/**
- * port_cfg - set port register bits
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the port register.
- * @bits: The data bits to set.
- * @set: The flag indicating whether the bits are to be set or not.
- *
- * This routine sets or resets the specified bits of the port register.
- */
-static void port_cfg(struct ksz_hw *hw, int port, int offset, u16 bits,
- int set)
-{
- u32 addr;
- u16 data;
-
- PORT_CTRL_ADDR(port, addr);
- addr += offset;
- data = readw(hw->io + addr);
- if (set)
- data |= bits;
- else
- data &= ~bits;
- writew(data, hw->io + addr);
-}
-
-/**
- * port_chk_shift - check port bit
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the register.
- * @shift: Number of bits to shift.
- *
- * This function checks whether the specified port is set in the register or
- * not.
- *
- * Return 0 if the port is not set.
- */
-static int port_chk_shift(struct ksz_hw *hw, int port, u32 addr, int shift)
-{
- u16 data;
- u16 bit = 1 << port;
-
- data = readw(hw->io + addr);
- data >>= shift;
- return (data & bit) == bit;
-}
-
-/**
- * port_cfg_shift - set port bit
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the register.
- * @shift: Number of bits to shift.
- * @set: The flag indicating whether the port is to be set or not.
- *
- * This routine sets or resets the specified port in the register.
- */
-static void port_cfg_shift(struct ksz_hw *hw, int port, u32 addr, int shift,
- int set)
-{
- u16 data;
- u16 bits = 1 << port;
-
- data = readw(hw->io + addr);
- bits <<= shift;
- if (set)
- data |= bits;
- else
- data &= ~bits;
- writew(data, hw->io + addr);
-}
-
-/**
- * port_r8 - read byte from port register
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the port register.
- * @data: Buffer to store the data.
- *
- * This routine reads a byte from the port register.
- */
-static void port_r8(struct ksz_hw *hw, int port, int offset, u8 *data)
-{
- u32 addr;
-
- PORT_CTRL_ADDR(port, addr);
- addr += offset;
- *data = readb(hw->io + addr);
-}
-
-/**
- * port_r16 - read word from port register.
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the port register.
- * @data: Buffer to store the data.
- *
- * This routine reads a word from the port register.
- */
-static void port_r16(struct ksz_hw *hw, int port, int offset, u16 *data)
-{
- u32 addr;
-
- PORT_CTRL_ADDR(port, addr);
- addr += offset;
- *data = readw(hw->io + addr);
-}
-
-/**
- * port_w16 - write word to port register.
- * @hw: The hardware instance.
- * @port: The port index.
- * @offset: The offset of the port register.
- * @data: Data to write.
- *
- * This routine writes a word to the port register.
- */
-static void port_w16(struct ksz_hw *hw, int port, int offset, u16 data)
-{
- u32 addr;
-
- PORT_CTRL_ADDR(port, addr);
- addr += offset;
- writew(data, hw->io + addr);
-}
-
-/**
- * sw_chk - check switch register bits
- * @hw: The hardware instance.
- * @addr: The address of the switch register.
- * @bits: The data bits to check.
- *
- * This function checks whether the specified bits of the switch register are
- * set or not.
- *
- * Return 0 if the bits are not set.
- */
-static int sw_chk(struct ksz_hw *hw, u32 addr, u16 bits)
-{
- u16 data;
-
- data = readw(hw->io + addr);
- return (data & bits) == bits;
-}
-
-/**
- * sw_cfg - set switch register bits
- * @hw: The hardware instance.
- * @addr: The address of the switch register.
- * @bits: The data bits to set.
- * @set: The flag indicating whether the bits are to be set or not.
- *
- * This function sets or resets the specified bits of the switch register.
- */
-static void sw_cfg(struct ksz_hw *hw, u32 addr, u16 bits, int set)
-{
- u16 data;
-
- data = readw(hw->io + addr);
- if (set)
- data |= bits;
- else
- data &= ~bits;
- writew(data, hw->io + addr);
-}
-
-/* Bandwidth */
-
-static inline void port_cfg_broad_storm(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_BROADCAST_STORM, set);
-}
-
-static inline int port_chk_broad_storm(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_BROADCAST_STORM);
-}
-
-/* Driver set switch broadcast storm protection at 10% rate. */
-#define BROADCAST_STORM_PROTECTION_RATE 10
-
-/* 148,800 frames * 67 ms / 100 */
-#define BROADCAST_STORM_VALUE 9969
-
-/**
- * sw_cfg_broad_storm - configure broadcast storm threshold
- * @hw: The hardware instance.
- * @percent: Broadcast storm threshold in percent of transmit rate.
- *
- * This routine configures the broadcast storm threshold of the switch.
- */
-static void sw_cfg_broad_storm(struct ksz_hw *hw, u8 percent)
-{
- u16 data;
- u32 value = ((u32) BROADCAST_STORM_VALUE * (u32) percent / 100);
-
- if (value > BROADCAST_STORM_RATE)
- value = BROADCAST_STORM_RATE;
-
- data = readw(hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
- data &= ~(BROADCAST_STORM_RATE_LO | BROADCAST_STORM_RATE_HI);
- data |= ((value & 0x00FF) << 8) | ((value & 0xFF00) >> 8);
- writew(data, hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
-}
-
-/**
- * sw_get_board_storm - get broadcast storm threshold
- * @hw: The hardware instance.
- * @percent: Buffer to store the broadcast storm threshold percentage.
- *
- * This routine retrieves the broadcast storm threshold of the switch.
- */
-static void sw_get_broad_storm(struct ksz_hw *hw, u8 *percent)
-{
- int num;
- u16 data;
-
- data = readw(hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
- num = (data & BROADCAST_STORM_RATE_HI);
- num <<= 8;
- num |= (data & BROADCAST_STORM_RATE_LO) >> 8;
- num = (num * 100 + BROADCAST_STORM_VALUE / 2) / BROADCAST_STORM_VALUE;
- *percent = (u8) num;
-}
-
-/**
- * sw_dis_broad_storm - disable broadstorm
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine disables the broadcast storm limit function of the switch.
- */
-static void sw_dis_broad_storm(struct ksz_hw *hw, int port)
-{
- port_cfg_broad_storm(hw, port, 0);
-}
-
-/**
- * sw_ena_broad_storm - enable broadcast storm
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine enables the broadcast storm limit function of the switch.
- */
-static void sw_ena_broad_storm(struct ksz_hw *hw, int port)
-{
- sw_cfg_broad_storm(hw, hw->ksz_switch->broad_per);
- port_cfg_broad_storm(hw, port, 1);
-}
-
-/**
- * sw_init_broad_storm - initialize broadcast storm
- * @hw: The hardware instance.
- *
- * This routine initializes the broadcast storm limit function of the switch.
- */
-static void sw_init_broad_storm(struct ksz_hw *hw)
-{
- int port;
-
- hw->ksz_switch->broad_per = 1;
- sw_cfg_broad_storm(hw, hw->ksz_switch->broad_per);
- for (port = 0; port < TOTAL_PORT_NUM; port++)
- sw_dis_broad_storm(hw, port);
- sw_cfg(hw, KS8842_SWITCH_CTRL_2_OFFSET, MULTICAST_STORM_DISABLE, 1);
-}
-
-/**
- * hw_cfg_broad_storm - configure broadcast storm
- * @hw: The hardware instance.
- * @percent: Broadcast storm threshold in percent of transmit rate.
- *
- * This routine configures the broadcast storm threshold of the switch.
- * It is called by user functions. The hardware should be acquired first.
- */
-static void hw_cfg_broad_storm(struct ksz_hw *hw, u8 percent)
-{
- if (percent > 100)
- percent = 100;
-
- sw_cfg_broad_storm(hw, percent);
- sw_get_broad_storm(hw, &percent);
- hw->ksz_switch->broad_per = percent;
-}
-
-/**
- * sw_dis_prio_rate - disable switch priority rate
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine disables the priority rate function of the switch.
- */
-static void sw_dis_prio_rate(struct ksz_hw *hw, int port)
-{
- u32 addr;
-
- PORT_CTRL_ADDR(port, addr);
- addr += KS8842_PORT_IN_RATE_OFFSET;
- writel(0, hw->io + addr);
-}
-
-/**
- * sw_init_prio_rate - initialize switch prioirty rate
- * @hw: The hardware instance.
- *
- * This routine initializes the priority rate function of the switch.
- */
-static void sw_init_prio_rate(struct ksz_hw *hw)
-{
- int port;
- int prio;
- struct ksz_switch *sw = hw->ksz_switch;
-
- for (port = 0; port < TOTAL_PORT_NUM; port++) {
- for (prio = 0; prio < PRIO_QUEUES; prio++) {
- sw->port_cfg[port].rx_rate[prio] =
- sw->port_cfg[port].tx_rate[prio] = 0;
- }
- sw_dis_prio_rate(hw, port);
- }
-}
-
-/* Communication */
-
-static inline void port_cfg_back_pressure(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_BACK_PRESSURE, set);
-}
-
-static inline void port_cfg_force_flow_ctrl(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_FORCE_FLOW_CTRL, set);
-}
-
-static inline int port_chk_back_pressure(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_BACK_PRESSURE);
-}
-
-static inline int port_chk_force_flow_ctrl(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_FORCE_FLOW_CTRL);
-}
-
-/* Spanning Tree */
-
-static inline void port_cfg_dis_learn(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_LEARN_DISABLE, set);
-}
-
-static inline void port_cfg_rx(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_RX_ENABLE, set);
-}
-
-static inline void port_cfg_tx(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_TX_ENABLE, set);
-}
-
-static inline void sw_cfg_fast_aging(struct ksz_hw *hw, int set)
-{
- sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET, SWITCH_FAST_AGING, set);
-}
-
-static inline void sw_flush_dyn_mac_table(struct ksz_hw *hw)
-{
- if (!(hw->overrides & FAST_AGING)) {
- sw_cfg_fast_aging(hw, 1);
- mdelay(1);
- sw_cfg_fast_aging(hw, 0);
- }
-}
-
-/* VLAN */
-
-static inline void port_cfg_ins_tag(struct ksz_hw *hw, int p, int insert)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_INSERT_TAG, insert);
-}
-
-static inline void port_cfg_rmv_tag(struct ksz_hw *hw, int p, int remove)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_REMOVE_TAG, remove);
-}
-
-static inline int port_chk_ins_tag(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_INSERT_TAG);
-}
-
-static inline int port_chk_rmv_tag(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_REMOVE_TAG);
-}
-
-static inline void port_cfg_dis_non_vid(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_DISCARD_NON_VID, set);
-}
-
-static inline void port_cfg_in_filter(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_INGRESS_VLAN_FILTER, set);
-}
-
-static inline int port_chk_dis_non_vid(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_DISCARD_NON_VID);
-}
-
-static inline int port_chk_in_filter(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_INGRESS_VLAN_FILTER);
-}
-
-/* Mirroring */
-
-static inline void port_cfg_mirror_sniffer(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_MIRROR_SNIFFER, set);
-}
-
-static inline void port_cfg_mirror_rx(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_MIRROR_RX, set);
-}
-
-static inline void port_cfg_mirror_tx(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_MIRROR_TX, set);
-}
-
-static inline void sw_cfg_mirror_rx_tx(struct ksz_hw *hw, int set)
-{
- sw_cfg(hw, KS8842_SWITCH_CTRL_2_OFFSET, SWITCH_MIRROR_RX_TX, set);
-}
-
-static void sw_init_mirror(struct ksz_hw *hw)
-{
- int port;
-
- for (port = 0; port < TOTAL_PORT_NUM; port++) {
- port_cfg_mirror_sniffer(hw, port, 0);
- port_cfg_mirror_rx(hw, port, 0);
- port_cfg_mirror_tx(hw, port, 0);
- }
- sw_cfg_mirror_rx_tx(hw, 0);
-}
-
-static inline void sw_cfg_unk_def_deliver(struct ksz_hw *hw, int set)
-{
- sw_cfg(hw, KS8842_SWITCH_CTRL_7_OFFSET,
- SWITCH_UNK_DEF_PORT_ENABLE, set);
-}
-
-static inline int sw_cfg_chk_unk_def_deliver(struct ksz_hw *hw)
-{
- return sw_chk(hw, KS8842_SWITCH_CTRL_7_OFFSET,
- SWITCH_UNK_DEF_PORT_ENABLE);
-}
-
-static inline void sw_cfg_unk_def_port(struct ksz_hw *hw, int port, int set)
-{
- port_cfg_shift(hw, port, KS8842_SWITCH_CTRL_7_OFFSET, 0, set);
-}
-
-static inline int sw_chk_unk_def_port(struct ksz_hw *hw, int port)
-{
- return port_chk_shift(hw, port, KS8842_SWITCH_CTRL_7_OFFSET, 0);
-}
-
-/* Priority */
-
-static inline void port_cfg_diffserv(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_DIFFSERV_ENABLE, set);
-}
-
-static inline void port_cfg_802_1p(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_802_1P_ENABLE, set);
-}
-
-static inline void port_cfg_replace_vid(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_USER_PRIORITY_CEILING, set);
-}
-
-static inline void port_cfg_prio(struct ksz_hw *hw, int p, int set)
-{
- port_cfg(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_PRIO_QUEUE_ENABLE, set);
-}
-
-static inline int port_chk_diffserv(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_DIFFSERV_ENABLE);
-}
-
-static inline int port_chk_802_1p(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_802_1P_ENABLE);
-}
-
-static inline int port_chk_replace_vid(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_2_OFFSET, PORT_USER_PRIORITY_CEILING);
-}
-
-static inline int port_chk_prio(struct ksz_hw *hw, int p)
-{
- return port_chk(hw, p,
- KS8842_PORT_CTRL_1_OFFSET, PORT_PRIO_QUEUE_ENABLE);
-}
-
-/**
- * sw_dis_diffserv - disable switch DiffServ priority
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine disables the DiffServ priority function of the switch.
- */
-static void sw_dis_diffserv(struct ksz_hw *hw, int port)
-{
- port_cfg_diffserv(hw, port, 0);
-}
-
-/**
- * sw_dis_802_1p - disable switch 802.1p priority
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine disables the 802.1p priority function of the switch.
- */
-static void sw_dis_802_1p(struct ksz_hw *hw, int port)
-{
- port_cfg_802_1p(hw, port, 0);
-}
-
-/**
- * sw_cfg_replace_null_vid -
- * @hw: The hardware instance.
- * @set: The flag to disable or enable.
- *
- */
-static void sw_cfg_replace_null_vid(struct ksz_hw *hw, int set)
-{
- sw_cfg(hw, KS8842_SWITCH_CTRL_3_OFFSET, SWITCH_REPLACE_NULL_VID, set);
-}
-
-/**
- * sw_cfg_replace_vid - enable switch 802.10 priority re-mapping
- * @hw: The hardware instance.
- * @port: The port index.
- * @set: The flag to disable or enable.
- *
- * This routine enables the 802.1p priority re-mapping function of the switch.
- * That allows 802.1p priority field to be replaced with the port's default
- * tag's priority value if the ingress packet's 802.1p priority has a higher
- * priority than port's default tag's priority.
- */
-static void sw_cfg_replace_vid(struct ksz_hw *hw, int port, int set)
-{
- port_cfg_replace_vid(hw, port, set);
-}
-
-/**
- * sw_cfg_port_based - configure switch port based priority
- * @hw: The hardware instance.
- * @port: The port index.
- * @prio: The priority to set.
- *
- * This routine configures the port based priority of the switch.
- */
-static void sw_cfg_port_based(struct ksz_hw *hw, int port, u8 prio)
-{
- u16 data;
-
- if (prio > PORT_BASED_PRIORITY_BASE)
- prio = PORT_BASED_PRIORITY_BASE;
-
- hw->ksz_switch->port_cfg[port].port_prio = prio;
-
- port_r16(hw, port, KS8842_PORT_CTRL_1_OFFSET, &data);
- data &= ~PORT_BASED_PRIORITY_MASK;
- data |= prio << PORT_BASED_PRIORITY_SHIFT;
- port_w16(hw, port, KS8842_PORT_CTRL_1_OFFSET, data);
-}
-
-/**
- * sw_dis_multi_queue - disable transmit multiple queues
- * @hw: The hardware instance.
- * @port: The port index.
- *
- * This routine disables the transmit multiple queues selection of the switch
- * port. Only single transmit queue on the port.
- */
-static void sw_dis_multi_queue(struct ksz_hw *hw, int port)
-{
- port_cfg_prio(hw, port, 0);
-}
-
-/**
- * sw_init_prio - initialize switch priority
- * @hw: The hardware instance.
- *
- * This routine initializes the switch QoS priority functions.
- */
-static void sw_init_prio(struct ksz_hw *hw)
-{
- int port;
- int tos;
- struct ksz_switch *sw = hw->ksz_switch;
-
- /*
- * Init all the 802.1p tag priority value to be assigned to different
- * priority queue.
- */
- sw->p_802_1p[0] = 0;
- sw->p_802_1p[1] = 0;
- sw->p_802_1p[2] = 1;
- sw->p_802_1p[3] = 1;
- sw->p_802_1p[4] = 2;
- sw->p_802_1p[5] = 2;
- sw->p_802_1p[6] = 3;
- sw->p_802_1p[7] = 3;
-
- /*
- * Init all the DiffServ priority value to be assigned to priority
- * queue 0.
- */
- for (tos = 0; tos < DIFFSERV_ENTRIES; tos++)
- sw->diffserv[tos] = 0;
-
- /* All QoS functions disabled. */
- for (port = 0; port < TOTAL_PORT_NUM; port++) {
- sw_dis_multi_queue(hw, port);
- sw_dis_diffserv(hw, port);
- sw_dis_802_1p(hw, port);
- sw_cfg_replace_vid(hw, port, 0);
-
- sw->port_cfg[port].port_prio = 0;
- sw_cfg_port_based(hw, port, sw->port_cfg[port].port_prio);
- }
- sw_cfg_replace_null_vid(hw, 0);
-}
-
-/**
- * port_get_def_vid - get port default VID.
- * @hw: The hardware instance.
- * @port: The port index.
- * @vid: Buffer to store the VID.
- *
- * This routine retrieves the default VID of the port.
- */
-static void port_get_def_vid(struct ksz_hw *hw, int port, u16 *vid)
-{
- u32 addr;
-
- PORT_CTRL_ADDR(port, addr);
- addr += KS8842_PORT_CTRL_VID_OFFSET;
- *vid = readw(hw->io + addr);
-}
-
-/**
- * sw_init_vlan - initialize switch VLAN
- * @hw: The hardware instance.
- *
- * This routine initializes the VLAN function of the switch.
- */
-static void sw_init_vlan(struct ksz_hw *hw)
-{
- int port;
- int entry;
- struct ksz_switch *sw = hw->ksz_switch;
-
- /* Read 16 VLAN entries from device's VLAN table. */
- for (entry = 0; entry < VLAN_TABLE_ENTRIES; entry++) {
- sw_r_vlan_table(hw, entry,
- &sw->vlan_table[entry].vid,
- &sw->vlan_table[entry].fid,
- &sw->vlan_table[entry].member);
- }
-
- for (port = 0; port < TOTAL_PORT_NUM; port++) {
- port_get_def_vid(hw, port, &sw->port_cfg[port].vid);
- sw->port_cfg[port].member = PORT_MASK;
- }
-}
-
-/**
- * sw_cfg_port_base_vlan - configure port-based VLAN membership
- * @hw: The hardware instance.
- * @port: The port index.
- * @member: The port-based VLAN membership.
- *
- * This routine configures the port-based VLAN membership of the port.
- */
-static void sw_cfg_port_base_vlan(struct ksz_hw *hw, int port, u8 member)
-{
- u32 addr;
- u8 data;
-
- PORT_CTRL_ADDR(port, addr);
- addr += KS8842_PORT_CTRL_2_OFFSET;
-
- data = readb(hw->io + addr);
- data &= ~PORT_VLAN_MEMBERSHIP;
- data |= (member & PORT_MASK);
- writeb(data, hw->io + addr);
-
- hw->ksz_switch->port_cfg[port].member = member;
-}
-
-/**
- * sw_get_addr - get the switch MAC address.
- * @hw: The hardware instance.
- * @mac_addr: Buffer to store the MAC address.
- *
- * This function retrieves the MAC address of the switch.
- */
-static inline void sw_get_addr(struct ksz_hw *hw, u8 *mac_addr)
-{
- int i;
-
- for (i = 0; i < 6; i += 2) {
- mac_addr[i] = readb(hw->io + KS8842_MAC_ADDR_0_OFFSET + i);
- mac_addr[1 + i] = readb(hw->io + KS8842_MAC_ADDR_1_OFFSET + i);
- }
-}
-
-/**
- * sw_set_addr - configure switch MAC address
- * @hw: The hardware instance.
- * @mac_addr: The MAC address.
- *
- * This function configures the MAC address of the switch.
- */
-static void sw_set_addr(struct ksz_hw *hw, u8 *mac_addr)
-{
- int i;
-
- for (i = 0; i < 6; i += 2) {
- writeb(mac_addr[i], hw->io + KS8842_MAC_ADDR_0_OFFSET + i);
- writeb(mac_addr[1 + i], hw->io + KS8842_MAC_ADDR_1_OFFSET + i);
- }
-}
-
-/**
- * sw_set_global_ctrl - set switch global control
- * @hw: The hardware instance.
- *
- * This routine sets the global control of the switch function.
- */
-static void sw_set_global_ctrl(struct ksz_hw *hw)
-{
- u16 data;
-
- /* Enable switch MII flow control. */
- data = readw(hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
- data |= SWITCH_FLOW_CTRL;
- writew(data, hw->io + KS8842_SWITCH_CTRL_3_OFFSET);
-
- data = readw(hw->io + KS8842_SWITCH_CTRL_1_OFFSET);
-
- /* Enable aggressive back off algorithm in half duplex mode. */
- data |= SWITCH_AGGR_BACKOFF;
-
- /* Enable automatic fast aging when link changed detected. */
- data |= SWITCH_AGING_ENABLE;
- data |= SWITCH_LINK_AUTO_AGING;
-
- if (hw->overrides & FAST_AGING)
- data |= SWITCH_FAST_AGING;
- else
- data &= ~SWITCH_FAST_AGING;
- writew(data, hw->io + KS8842_SWITCH_CTRL_1_OFFSET);
-
- data = readw(hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
-
- /* Enable no excessive collision drop. */
- data |= NO_EXC_COLLISION_DROP;
- writew(data, hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
-}
-
-enum {
- STP_STATE_DISABLED = 0,
- STP_STATE_LISTENING,
- STP_STATE_LEARNING,
- STP_STATE_FORWARDING,
- STP_STATE_BLOCKED,
- STP_STATE_SIMPLE
-};
-
-/**
- * port_set_stp_state - configure port spanning tree state
- * @hw: The hardware instance.
- * @port: The port index.
- * @state: The spanning tree state.
- *
- * This routine configures the spanning tree state of the port.
- */
-static void port_set_stp_state(struct ksz_hw *hw, int port, int state)
-{
- u16 data;
-
- port_r16(hw, port, KS8842_PORT_CTRL_2_OFFSET, &data);
- switch (state) {
- case STP_STATE_DISABLED:
- data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE);
- data |= PORT_LEARN_DISABLE;
- break;
- case STP_STATE_LISTENING:
-/*
- * No need to turn on transmit because of port direct mode.
- * Turning on receive is required if static MAC table is not setup.
- */
- data &= ~PORT_TX_ENABLE;
- data |= PORT_RX_ENABLE;
- data |= PORT_LEARN_DISABLE;
- break;
- case STP_STATE_LEARNING:
- data &= ~PORT_TX_ENABLE;
- data |= PORT_RX_ENABLE;
- data &= ~PORT_LEARN_DISABLE;
- break;
- case STP_STATE_FORWARDING:
- data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
- data &= ~PORT_LEARN_DISABLE;
- break;
- case STP_STATE_BLOCKED:
-/*
- * Need to setup static MAC table with override to keep receiving BPDU
- * messages. See sw_init_stp routine.
- */
- data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE);
- data |= PORT_LEARN_DISABLE;
- break;
- case STP_STATE_SIMPLE:
- data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
- data |= PORT_LEARN_DISABLE;
- break;
- }
- port_w16(hw, port, KS8842_PORT_CTRL_2_OFFSET, data);
- hw->ksz_switch->port_cfg[port].stp_state = state;
-}
-
-#define STP_ENTRY 0
-#define BROADCAST_ENTRY 1
-#define BRIDGE_ADDR_ENTRY 2
-#define IPV6_ADDR_ENTRY 3
-
-/**
- * sw_clr_sta_mac_table - clear static MAC table
- * @hw: The hardware instance.
- *
- * This routine clears the static MAC table.
- */
-static void sw_clr_sta_mac_table(struct ksz_hw *hw)
-{
- struct ksz_mac_table *entry;
- int i;
-
- for (i = 0; i < STATIC_MAC_TABLE_ENTRIES; i++) {
- entry = &hw->ksz_switch->mac_table[i];
- sw_w_sta_mac_table(hw, i,
- entry->mac_addr, entry->ports,
- entry->override, 0,
- entry->use_fid, entry->fid);
- }
-}
-
-/**
- * sw_init_stp - initialize switch spanning tree support
- * @hw: The hardware instance.
- *
- * This routine initializes the spanning tree support of the switch.
- */
-static void sw_init_stp(struct ksz_hw *hw)
-{
- struct ksz_mac_table *entry;
-
- entry = &hw->ksz_switch->mac_table[STP_ENTRY];
- entry->mac_addr[0] = 0x01;
- entry->mac_addr[1] = 0x80;
- entry->mac_addr[2] = 0xC2;
- entry->mac_addr[3] = 0x00;
- entry->mac_addr[4] = 0x00;
- entry->mac_addr[5] = 0x00;
- entry->ports = HOST_MASK;
- entry->override = 1;
- entry->valid = 1;
- sw_w_sta_mac_table(hw, STP_ENTRY,
- entry->mac_addr, entry->ports,
- entry->override, entry->valid,
- entry->use_fid, entry->fid);
-}
-
-/**
- * sw_block_addr - block certain packets from the host port
- * @hw: The hardware instance.
- *
- * This routine blocks certain packets from reaching to the host port.
- */
-static void sw_block_addr(struct ksz_hw *hw)
-{
- struct ksz_mac_table *entry;
- int i;
-
- for (i = BROADCAST_ENTRY; i <= IPV6_ADDR_ENTRY; i++) {
- entry = &hw->ksz_switch->mac_table[i];
- entry->valid = 0;
- sw_w_sta_mac_table(hw, i,
- entry->mac_addr, entry->ports,
- entry->override, entry->valid,
- entry->use_fid, entry->fid);
- }
-}
-
-#define PHY_LINK_SUPPORT \
- (PHY_AUTO_NEG_ASYM_PAUSE | \
- PHY_AUTO_NEG_SYM_PAUSE | \
- PHY_AUTO_NEG_100BT4 | \
- PHY_AUTO_NEG_100BTX_FD | \
- PHY_AUTO_NEG_100BTX | \
- PHY_AUTO_NEG_10BT_FD | \
- PHY_AUTO_NEG_10BT)
-
-static inline void hw_r_phy_ctrl(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_CTRL_OFFSET);
-}
-
-static inline void hw_w_phy_ctrl(struct ksz_hw *hw, int phy, u16 data)
-{
- writew(data, hw->io + phy + KS884X_PHY_CTRL_OFFSET);
-}
-
-static inline void hw_r_phy_link_stat(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_STATUS_OFFSET);
-}
-
-static inline void hw_r_phy_auto_neg(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_AUTO_NEG_OFFSET);
-}
-
-static inline void hw_w_phy_auto_neg(struct ksz_hw *hw, int phy, u16 data)
-{
- writew(data, hw->io + phy + KS884X_PHY_AUTO_NEG_OFFSET);
-}
-
-static inline void hw_r_phy_rem_cap(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_REMOTE_CAP_OFFSET);
-}
-
-static inline void hw_r_phy_crossover(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_CTRL_OFFSET);
-}
-
-static inline void hw_w_phy_crossover(struct ksz_hw *hw, int phy, u16 data)
-{
- writew(data, hw->io + phy + KS884X_PHY_CTRL_OFFSET);
-}
-
-static inline void hw_r_phy_polarity(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_PHY_CTRL_OFFSET);
-}
-
-static inline void hw_w_phy_polarity(struct ksz_hw *hw, int phy, u16 data)
-{
- writew(data, hw->io + phy + KS884X_PHY_PHY_CTRL_OFFSET);
-}
-
-static inline void hw_r_phy_link_md(struct ksz_hw *hw, int phy, u16 *data)
-{
- *data = readw(hw->io + phy + KS884X_PHY_LINK_MD_OFFSET);
-}
-
-static inline void hw_w_phy_link_md(struct ksz_hw *hw, int phy, u16 data)
-{
- writew(data, hw->io + phy + KS884X_PHY_LINK_MD_OFFSET);
-}
-
-/**
- * hw_r_phy - read data from PHY register
- * @hw: The hardware instance.
- * @port: Port to read.
- * @reg: PHY register to read.
- * @val: Buffer to store the read data.
- *
- * This routine reads data from the PHY register.
- */
-static void hw_r_phy(struct ksz_hw *hw, int port, u16 reg, u16 *val)
-{
- int phy;
-
- phy = KS884X_PHY_1_CTRL_OFFSET + port * PHY_CTRL_INTERVAL + reg;
- *val = readw(hw->io + phy);
-}
-
-/**
- * port_w_phy - write data to PHY register
- * @hw: The hardware instance.
- * @port: Port to write.
- * @reg: PHY register to write.
- * @val: Word data to write.
- *
- * This routine writes data to the PHY register.
- */
-static void hw_w_phy(struct ksz_hw *hw, int port, u16 reg, u16 val)
-{
- int phy;
-
- phy = KS884X_PHY_1_CTRL_OFFSET + port * PHY_CTRL_INTERVAL + reg;
- writew(val, hw->io + phy);
-}
-
-/*
- * EEPROM access functions
- */
-
-#define AT93C_CODE 0
-#define AT93C_WR_OFF 0x00
-#define AT93C_WR_ALL 0x10
-#define AT93C_ER_ALL 0x20
-#define AT93C_WR_ON 0x30
-
-#define AT93C_WRITE 1
-#define AT93C_READ 2
-#define AT93C_ERASE 3
-
-#define EEPROM_DELAY 4
-
-static inline void drop_gpio(struct ksz_hw *hw, u8 gpio)
-{
- u16 data;
-
- data = readw(hw->io + KS884X_EEPROM_CTRL_OFFSET);
- data &= ~gpio;
- writew(data, hw->io + KS884X_EEPROM_CTRL_OFFSET);
-}
-
-static inline void raise_gpio(struct ksz_hw *hw, u8 gpio)
-{
- u16 data;
-
- data = readw(hw->io + KS884X_EEPROM_CTRL_OFFSET);
- data |= gpio;
- writew(data, hw->io + KS884X_EEPROM_CTRL_OFFSET);
-}
-
-static inline u8 state_gpio(struct ksz_hw *hw, u8 gpio)
-{
- u16 data;
-
- data = readw(hw->io + KS884X_EEPROM_CTRL_OFFSET);
- return (u8)(data & gpio);
-}
-
-static void eeprom_clk(struct ksz_hw *hw)
-{
- raise_gpio(hw, EEPROM_SERIAL_CLOCK);
- udelay(EEPROM_DELAY);
- drop_gpio(hw, EEPROM_SERIAL_CLOCK);
- udelay(EEPROM_DELAY);
-}
-
-static u16 spi_r(struct ksz_hw *hw)
-{
- int i;
- u16 temp = 0;
-
- for (i = 15; i >= 0; i--) {
- raise_gpio(hw, EEPROM_SERIAL_CLOCK);
- udelay(EEPROM_DELAY);
-
- temp |= (state_gpio(hw, EEPROM_DATA_IN)) ? 1 << i : 0;
-
- drop_gpio(hw, EEPROM_SERIAL_CLOCK);
- udelay(EEPROM_DELAY);
- }
- return temp;
-}
-
-static void spi_w(struct ksz_hw *hw, u16 data)
-{
- int i;
-
- for (i = 15; i >= 0; i--) {
- (data & (0x01 << i)) ? raise_gpio(hw, EEPROM_DATA_OUT) :
- drop_gpio(hw, EEPROM_DATA_OUT);
- eeprom_clk(hw);
- }
-}
-
-static void spi_reg(struct ksz_hw *hw, u8 data, u8 reg)
-{
- int i;
-
- /* Initial start bit */
- raise_gpio(hw, EEPROM_DATA_OUT);
- eeprom_clk(hw);
-
- /* AT93C operation */
- for (i = 1; i >= 0; i--) {
- (data & (0x01 << i)) ? raise_gpio(hw, EEPROM_DATA_OUT) :
- drop_gpio(hw, EEPROM_DATA_OUT);
- eeprom_clk(hw);
- }
-
- /* Address location */
- for (i = 5; i >= 0; i--) {
- (reg & (0x01 << i)) ? raise_gpio(hw, EEPROM_DATA_OUT) :
- drop_gpio(hw, EEPROM_DATA_OUT);
- eeprom_clk(hw);
- }
-}
-
-#define EEPROM_DATA_RESERVED 0
-#define EEPROM_DATA_MAC_ADDR_0 1
-#define EEPROM_DATA_MAC_ADDR_1 2
-#define EEPROM_DATA_MAC_ADDR_2 3
-#define EEPROM_DATA_SUBSYS_ID 4
-#define EEPROM_DATA_SUBSYS_VEN_ID 5
-#define EEPROM_DATA_PM_CAP 6
-
-/* User defined EEPROM data */
-#define EEPROM_DATA_OTHER_MAC_ADDR 9
-
-/**
- * eeprom_read - read from AT93C46 EEPROM
- * @hw: The hardware instance.
- * @reg: The register offset.
- *
- * This function reads a word from the AT93C46 EEPROM.
- *
- * Return the data value.
- */
-static u16 eeprom_read(struct ksz_hw *hw, u8 reg)
-{
- u16 data;
-
- raise_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
-
- spi_reg(hw, AT93C_READ, reg);
- data = spi_r(hw);
-
- drop_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
-
- return data;
-}
-
-/**
- * eeprom_write - write to AT93C46 EEPROM
- * @hw: The hardware instance.
- * @reg: The register offset.
- * @data: The data value.
- *
- * This procedure writes a word to the AT93C46 EEPROM.
- */
-static void eeprom_write(struct ksz_hw *hw, u8 reg, u16 data)
-{
- int timeout;
-
- raise_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
-
- /* Enable write. */
- spi_reg(hw, AT93C_CODE, AT93C_WR_ON);
- drop_gpio(hw, EEPROM_CHIP_SELECT);
- udelay(1);
-
- /* Erase the register. */
- raise_gpio(hw, EEPROM_CHIP_SELECT);
- spi_reg(hw, AT93C_ERASE, reg);
- drop_gpio(hw, EEPROM_CHIP_SELECT);
- udelay(1);
-
- /* Check operation complete. */
- raise_gpio(hw, EEPROM_CHIP_SELECT);
- timeout = 8;
- mdelay(2);
- do {
- mdelay(1);
- } while (!state_gpio(hw, EEPROM_DATA_IN) && --timeout);
- drop_gpio(hw, EEPROM_CHIP_SELECT);
- udelay(1);
-
- /* Write the register. */
- raise_gpio(hw, EEPROM_CHIP_SELECT);
- spi_reg(hw, AT93C_WRITE, reg);
- spi_w(hw, data);
- drop_gpio(hw, EEPROM_CHIP_SELECT);
- udelay(1);
-
- /* Check operation complete. */
- raise_gpio(hw, EEPROM_CHIP_SELECT);
- timeout = 8;
- mdelay(2);
- do {
- mdelay(1);
- } while (!state_gpio(hw, EEPROM_DATA_IN) && --timeout);
- drop_gpio(hw, EEPROM_CHIP_SELECT);
- udelay(1);
-
- /* Disable write. */
- raise_gpio(hw, EEPROM_CHIP_SELECT);
- spi_reg(hw, AT93C_CODE, AT93C_WR_OFF);
-
- drop_gpio(hw, EEPROM_ACCESS_ENABLE | EEPROM_CHIP_SELECT);
-}
-
-/*
- * Link detection routines
- */
-
-static u16 advertised_flow_ctrl(struct ksz_port *port, u16 ctrl)
-{
- ctrl &= ~PORT_AUTO_NEG_SYM_PAUSE;
- switch (port->flow_ctrl) {
- case PHY_FLOW_CTRL:
- ctrl |= PORT_AUTO_NEG_SYM_PAUSE;
- break;
- /* Not supported. */
- case PHY_TX_ONLY:
- case PHY_RX_ONLY:
- default:
- break;
- }
- return ctrl;
-}
-
-static void set_flow_ctrl(struct ksz_hw *hw, int rx, int tx)
-{
- u32 rx_cfg;
- u32 tx_cfg;
-
- rx_cfg = hw->rx_cfg;
- tx_cfg = hw->tx_cfg;
- if (rx)
- hw->rx_cfg |= DMA_RX_FLOW_ENABLE;
- else
- hw->rx_cfg &= ~DMA_RX_FLOW_ENABLE;
- if (tx)
- hw->tx_cfg |= DMA_TX_FLOW_ENABLE;
- else
- hw->tx_cfg &= ~DMA_TX_FLOW_ENABLE;
- if (hw->enabled) {
- if (rx_cfg != hw->rx_cfg)
- writel(hw->rx_cfg, hw->io + KS_DMA_RX_CTRL);
- if (tx_cfg != hw->tx_cfg)
- writel(hw->tx_cfg, hw->io + KS_DMA_TX_CTRL);
- }
-}
-
-static void determine_flow_ctrl(struct ksz_hw *hw, struct ksz_port *port,
- u16 local, u16 remote)
-{
- int rx;
- int tx;
-
- if (hw->overrides & PAUSE_FLOW_CTRL)
- return;
-
- rx = tx = 0;
- if (port->force_link)
- rx = tx = 1;
- if (remote & PHY_AUTO_NEG_SYM_PAUSE) {
- if (local & PHY_AUTO_NEG_SYM_PAUSE) {
- rx = tx = 1;
- } else if ((remote & PHY_AUTO_NEG_ASYM_PAUSE) &&
- (local & PHY_AUTO_NEG_PAUSE) ==
- PHY_AUTO_NEG_ASYM_PAUSE) {
- tx = 1;
- }
- } else if (remote & PHY_AUTO_NEG_ASYM_PAUSE) {
- if ((local & PHY_AUTO_NEG_PAUSE) == PHY_AUTO_NEG_PAUSE)
- rx = 1;
- }
- if (!hw->ksz_switch)
- set_flow_ctrl(hw, rx, tx);
-}
-
-static inline void port_cfg_change(struct ksz_hw *hw, struct ksz_port *port,
- struct ksz_port_info *info, u16 link_status)
-{
- if ((hw->features & HALF_DUPLEX_SIGNAL_BUG) &&
- !(hw->overrides & PAUSE_FLOW_CTRL)) {
- u32 cfg = hw->tx_cfg;
-
- /* Disable flow control in the half duplex mode. */
- if (1 == info->duplex)
- hw->tx_cfg &= ~DMA_TX_FLOW_ENABLE;
- if (hw->enabled && cfg != hw->tx_cfg)
- writel(hw->tx_cfg, hw->io + KS_DMA_TX_CTRL);
- }
-}
-
-/**
- * port_get_link_speed - get current link status
- * @port: The port instance.
- *
- * This routine reads PHY registers to determine the current link status of the
- * switch ports.
- */
-static void port_get_link_speed(struct ksz_port *port)
-{
- uint interrupt;
- struct ksz_port_info *info;
- struct ksz_port_info *linked = NULL;
- struct ksz_hw *hw = port->hw;
- u16 data;
- u16 status;
- u8 local;
- u8 remote;
- int i;
- int p;
- int change = 0;
-
- interrupt = hw_block_intr(hw);
-
- for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
- info = &hw->port_info[p];
- port_r16(hw, p, KS884X_PORT_CTRL_4_OFFSET, &data);
- port_r16(hw, p, KS884X_PORT_STATUS_OFFSET, &status);
-
- /*
- * Link status is changing all the time even when there is no
- * cable connection!
- */
- remote = status & (PORT_AUTO_NEG_COMPLETE |
- PORT_STATUS_LINK_GOOD);
- local = (u8) data;
-
- /* No change to status. */
- if (local == info->advertised && remote == info->partner)
- continue;
-
- info->advertised = local;
- info->partner = remote;
- if (status & PORT_STATUS_LINK_GOOD) {
-
- /* Remember the first linked port. */
- if (!linked)
- linked = info;
-
- info->tx_rate = 10 * TX_RATE_UNIT;
- if (status & PORT_STATUS_SPEED_100MBIT)
- info->tx_rate = 100 * TX_RATE_UNIT;
-
- info->duplex = 1;
- if (status & PORT_STATUS_FULL_DUPLEX)
- info->duplex = 2;
-
- if (media_connected != info->state) {
- hw_r_phy(hw, p, KS884X_PHY_AUTO_NEG_OFFSET,
- &data);
- hw_r_phy(hw, p, KS884X_PHY_REMOTE_CAP_OFFSET,
- &status);
- determine_flow_ctrl(hw, port, data, status);
- if (hw->ksz_switch) {
- port_cfg_back_pressure(hw, p,
- (1 == info->duplex));
- }
- change |= 1 << i;
- port_cfg_change(hw, port, info, status);
- }
- info->state = media_connected;
- } else {
- if (media_disconnected != info->state) {
- change |= 1 << i;
-
- /* Indicate the link just goes down. */
- hw->port_mib[p].link_down = 1;
- }
- info->state = media_disconnected;
- }
- hw->port_mib[p].state = (u8) info->state;
- }
-
- if (linked && media_disconnected == port->linked->state)
- port->linked = linked;
-
- hw_restore_intr(hw, interrupt);
-}
-
-#define PHY_RESET_TIMEOUT 10
-
-/**
- * port_set_link_speed - set port speed
- * @port: The port instance.
- *
- * This routine sets the link speed of the switch ports.
- */
-static void port_set_link_speed(struct ksz_port *port)
-{
- struct ksz_port_info *info;
- struct ksz_hw *hw = port->hw;
- u16 data;
- u16 cfg;
- u8 status;
- int i;
- int p;
-
- for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
- info = &hw->port_info[p];
-
- port_r16(hw, p, KS884X_PORT_CTRL_4_OFFSET, &data);
- port_r8(hw, p, KS884X_PORT_STATUS_OFFSET, &status);
-
- cfg = 0;
- if (status & PORT_STATUS_LINK_GOOD)
- cfg = data;
-
- data |= PORT_AUTO_NEG_ENABLE;
- data = advertised_flow_ctrl(port, data);
-
- data |= PORT_AUTO_NEG_100BTX_FD | PORT_AUTO_NEG_100BTX |
- PORT_AUTO_NEG_10BT_FD | PORT_AUTO_NEG_10BT;
-
- /* Check if manual configuration is specified by the user. */
- if (port->speed || port->duplex) {
- if (10 == port->speed)
- data &= ~(PORT_AUTO_NEG_100BTX_FD |
- PORT_AUTO_NEG_100BTX);
- else if (100 == port->speed)
- data &= ~(PORT_AUTO_NEG_10BT_FD |
- PORT_AUTO_NEG_10BT);
- if (1 == port->duplex)
- data &= ~(PORT_AUTO_NEG_100BTX_FD |
- PORT_AUTO_NEG_10BT_FD);
- else if (2 == port->duplex)
- data &= ~(PORT_AUTO_NEG_100BTX |
- PORT_AUTO_NEG_10BT);
- }
- if (data != cfg) {
- data |= PORT_AUTO_NEG_RESTART;
- port_w16(hw, p, KS884X_PORT_CTRL_4_OFFSET, data);
- }
- }
-}
-
-/**
- * port_force_link_speed - force port speed
- * @port: The port instance.
- *
- * This routine forces the link speed of the switch ports.
- */
-static void port_force_link_speed(struct ksz_port *port)
-{
- struct ksz_hw *hw = port->hw;
- u16 data;
- int i;
- int phy;
- int p;
-
- for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
- phy = KS884X_PHY_1_CTRL_OFFSET + p * PHY_CTRL_INTERVAL;
- hw_r_phy_ctrl(hw, phy, &data);
-
- data &= ~PHY_AUTO_NEG_ENABLE;
-
- if (10 == port->speed)
- data &= ~PHY_SPEED_100MBIT;
- else if (100 == port->speed)
- data |= PHY_SPEED_100MBIT;
- if (1 == port->duplex)
- data &= ~PHY_FULL_DUPLEX;
- else if (2 == port->duplex)
- data |= PHY_FULL_DUPLEX;
- hw_w_phy_ctrl(hw, phy, data);
- }
-}
-
-static void port_set_power_saving(struct ksz_port *port, int enable)
-{
- struct ksz_hw *hw = port->hw;
- int i;
- int p;
-
- for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++)
- port_cfg(hw, p,
- KS884X_PORT_CTRL_4_OFFSET, PORT_POWER_DOWN, enable);
-}
-
-/*
- * KSZ8841 power management functions
- */
-
-/**
- * hw_chk_wol_pme_status - check PMEN pin
- * @hw: The hardware instance.
- *
- * This function is used to check PMEN pin is asserted.
- *
- * Return 1 if PMEN pin is asserted; otherwise, 0.
- */
-static int hw_chk_wol_pme_status(struct ksz_hw *hw)
-{
- struct dev_info *hw_priv = container_of(hw, struct dev_info, hw);
- struct pci_dev *pdev = hw_priv->pdev;
- u16 data;
-
- if (!pdev->pm_cap)
- return 0;
- pci_read_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, &data);
- return (data & PCI_PM_CTRL_PME_STATUS) == PCI_PM_CTRL_PME_STATUS;
-}
-
-/**
- * hw_clr_wol_pme_status - clear PMEN pin
- * @hw: The hardware instance.
- *
- * This routine is used to clear PME_Status to deassert PMEN pin.
- */
-static void hw_clr_wol_pme_status(struct ksz_hw *hw)
-{
- struct dev_info *hw_priv = container_of(hw, struct dev_info, hw);
- struct pci_dev *pdev = hw_priv->pdev;
- u16 data;
-
- if (!pdev->pm_cap)
- return;
-
- /* Clear PME_Status to deassert PMEN pin. */
- pci_read_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, &data);
- data |= PCI_PM_CTRL_PME_STATUS;
- pci_write_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, data);
-}
-
-/**
- * hw_cfg_wol_pme - enable or disable Wake-on-LAN
- * @hw: The hardware instance.
- * @set: The flag indicating whether to enable or disable.
- *
- * This routine is used to enable or disable Wake-on-LAN.
- */
-static void hw_cfg_wol_pme(struct ksz_hw *hw, int set)
-{
- struct dev_info *hw_priv = container_of(hw, struct dev_info, hw);
- struct pci_dev *pdev = hw_priv->pdev;
- u16 data;
-
- if (!pdev->pm_cap)
- return;
- pci_read_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, &data);
- data &= ~PCI_PM_CTRL_STATE_MASK;
- if (set)
- data |= PCI_PM_CTRL_PME_ENABLE | PCI_D3hot;
- else
- data &= ~PCI_PM_CTRL_PME_ENABLE;
- pci_write_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, data);
-}
-
-/**
- * hw_cfg_wol - configure Wake-on-LAN features
- * @hw: The hardware instance.
- * @frame: The pattern frame bit.
- * @set: The flag indicating whether to enable or disable.
- *
- * This routine is used to enable or disable certain Wake-on-LAN features.
- */
-static void hw_cfg_wol(struct ksz_hw *hw, u16 frame, int set)
-{
- u16 data;
-
- data = readw(hw->io + KS8841_WOL_CTRL_OFFSET);
- if (set)
- data |= frame;
- else
- data &= ~frame;
- writew(data, hw->io + KS8841_WOL_CTRL_OFFSET);
-}
-
-/**
- * hw_set_wol_frame - program Wake-on-LAN pattern
- * @hw: The hardware instance.
- * @i: The frame index.
- * @mask_size: The size of the mask.
- * @mask: Mask to ignore certain bytes in the pattern.
- * @frame_size: The size of the frame.
- * @pattern: The frame data.
- *
- * This routine is used to program Wake-on-LAN pattern.
- */
-static void hw_set_wol_frame(struct ksz_hw *hw, int i, uint mask_size,
- const u8 *mask, uint frame_size, const u8 *pattern)
-{
- int bits;
- int from;
- int len;
- int to;
- u32 crc;
- u8 data[64];
- u8 val = 0;
-
- if (frame_size > mask_size * 8)
- frame_size = mask_size * 8;
- if (frame_size > 64)
- frame_size = 64;
-
- i *= 0x10;
- writel(0, hw->io + KS8841_WOL_FRAME_BYTE0_OFFSET + i);
- writel(0, hw->io + KS8841_WOL_FRAME_BYTE2_OFFSET + i);
-
- bits = len = from = to = 0;
- do {
- if (bits) {
- if ((val & 1))
- data[to++] = pattern[from];
- val >>= 1;
- ++from;
- --bits;
- } else {
- val = mask[len];
- writeb(val, hw->io + KS8841_WOL_FRAME_BYTE0_OFFSET + i
- + len);
- ++len;
- if (val)
- bits = 8;
- else
- from += 8;
- }
- } while (from < (int) frame_size);
- if (val) {
- bits = mask[len - 1];
- val <<= (from % 8);
- bits &= ~val;
- writeb(bits, hw->io + KS8841_WOL_FRAME_BYTE0_OFFSET + i + len -
- 1);
- }
- crc = ether_crc(to, data);
- writel(crc, hw->io + KS8841_WOL_FRAME_CRC_OFFSET + i);
-}
-
-/**
- * hw_add_wol_arp - add ARP pattern
- * @hw: The hardware instance.
- * @ip_addr: The IPv4 address assigned to the device.
- *
- * This routine is used to add ARP pattern for waking up the host.
- */
-static void hw_add_wol_arp(struct ksz_hw *hw, const u8 *ip_addr)
-{
- static const u8 mask[6] = { 0x3F, 0xF0, 0x3F, 0x00, 0xC0, 0x03 };
- u8 pattern[42] = {
- 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x08, 0x06,
- 0x00, 0x01, 0x08, 0x00, 0x06, 0x04, 0x00, 0x01,
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x00, 0x00 };
-
- memcpy(&pattern[38], ip_addr, 4);
- hw_set_wol_frame(hw, 3, 6, mask, 42, pattern);
-}
-
-/**
- * hw_add_wol_bcast - add broadcast pattern
- * @hw: The hardware instance.
- *
- * This routine is used to add broadcast pattern for waking up the host.
- */
-static void hw_add_wol_bcast(struct ksz_hw *hw)
-{
- static const u8 mask[] = { 0x3F };
- static const u8 pattern[] = { 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF };
-
- hw_set_wol_frame(hw, 2, 1, mask, MAC_ADDR_LEN, pattern);
-}
-
-/**
- * hw_add_wol_mcast - add multicast pattern
- * @hw: The hardware instance.
- *
- * This routine is used to add multicast pattern for waking up the host.
- *
- * It is assumed the multicast packet is the ICMPv6 neighbor solicitation used
- * by IPv6 ping command. Note that multicast packets are filtred through the
- * multicast hash table, so not all multicast packets can wake up the host.
- */
-static void hw_add_wol_mcast(struct ksz_hw *hw)
-{
- static const u8 mask[] = { 0x3F };
- u8 pattern[] = { 0x33, 0x33, 0xFF, 0x00, 0x00, 0x00 };
-
- memcpy(&pattern[3], &hw->override_addr[3], 3);
- hw_set_wol_frame(hw, 1, 1, mask, 6, pattern);
-}
-
-/**
- * hw_add_wol_ucast - add unicast pattern
- * @hw: The hardware instance.
- *
- * This routine is used to add unicast pattern to wakeup the host.
- *
- * It is assumed the unicast packet is directed to the device, as the hardware
- * can only receive them in normal case.
- */
-static void hw_add_wol_ucast(struct ksz_hw *hw)
-{
- static const u8 mask[] = { 0x3F };
-
- hw_set_wol_frame(hw, 0, 1, mask, MAC_ADDR_LEN, hw->override_addr);
-}
-
-/**
- * hw_enable_wol - enable Wake-on-LAN
- * @hw: The hardware instance.
- * @wol_enable: The Wake-on-LAN settings.
- * @net_addr: The IPv4 address assigned to the device.
- *
- * This routine is used to enable Wake-on-LAN depending on driver settings.
- */
-static void hw_enable_wol(struct ksz_hw *hw, u32 wol_enable, const u8 *net_addr)
-{
- hw_cfg_wol(hw, KS8841_WOL_MAGIC_ENABLE, (wol_enable & WAKE_MAGIC));
- hw_cfg_wol(hw, KS8841_WOL_FRAME0_ENABLE, (wol_enable & WAKE_UCAST));
- hw_add_wol_ucast(hw);
- hw_cfg_wol(hw, KS8841_WOL_FRAME1_ENABLE, (wol_enable & WAKE_MCAST));
- hw_add_wol_mcast(hw);
- hw_cfg_wol(hw, KS8841_WOL_FRAME2_ENABLE, (wol_enable & WAKE_BCAST));
- hw_cfg_wol(hw, KS8841_WOL_FRAME3_ENABLE, (wol_enable & WAKE_ARP));
- hw_add_wol_arp(hw, net_addr);
-}
-
-/**
- * hw_init - check driver is correct for the hardware
- * @hw: The hardware instance.
- *
- * This function checks the hardware is correct for this driver and sets the
- * hardware up for proper initialization.
- *
- * Return number of ports or 0 if not right.
- */
-static int hw_init(struct ksz_hw *hw)
-{
- int rc = 0;
- u16 data;
- u16 revision;
-
- /* Set bus speed to 125MHz. */
- writew(BUS_SPEED_125_MHZ, hw->io + KS884X_BUS_CTRL_OFFSET);
-
- /* Check KSZ884x chip ID. */
- data = readw(hw->io + KS884X_CHIP_ID_OFFSET);
-
- revision = (data & KS884X_REVISION_MASK) >> KS884X_REVISION_SHIFT;
- data &= KS884X_CHIP_ID_MASK_41;
- if (REG_CHIP_ID_41 == data)
- rc = 1;
- else if (REG_CHIP_ID_42 == data)
- rc = 2;
- else
- return 0;
-
- /* Setup hardware features or bug workarounds. */
- if (revision <= 1) {
- hw->features |= SMALL_PACKET_TX_BUG;
- if (1 == rc)
- hw->features |= HALF_DUPLEX_SIGNAL_BUG;
- }
- return rc;
-}
-
-/**
- * hw_reset - reset the hardware
- * @hw: The hardware instance.
- *
- * This routine resets the hardware.
- */
-static void hw_reset(struct ksz_hw *hw)
-{
- writew(GLOBAL_SOFTWARE_RESET, hw->io + KS884X_GLOBAL_CTRL_OFFSET);
-
- /* Wait for device to reset. */
- mdelay(10);
-
- /* Write 0 to clear device reset. */
- writew(0, hw->io + KS884X_GLOBAL_CTRL_OFFSET);
-}
-
-/**
- * hw_setup - setup the hardware
- * @hw: The hardware instance.
- *
- * This routine setup the hardware for proper operation.
- */
-static void hw_setup(struct ksz_hw *hw)
-{
-#if SET_DEFAULT_LED
- u16 data;
-
- /* Change default LED mode. */
- data = readw(hw->io + KS8842_SWITCH_CTRL_5_OFFSET);
- data &= ~LED_MODE;
- data |= SET_DEFAULT_LED;
- writew(data, hw->io + KS8842_SWITCH_CTRL_5_OFFSET);
-#endif
-
- /* Setup transmit control. */
- hw->tx_cfg = (DMA_TX_PAD_ENABLE | DMA_TX_CRC_ENABLE |
- (DMA_BURST_DEFAULT << DMA_BURST_SHIFT) | DMA_TX_ENABLE);
-
- /* Setup receive control. */
- hw->rx_cfg = (DMA_RX_BROADCAST | DMA_RX_UNICAST |
- (DMA_BURST_DEFAULT << DMA_BURST_SHIFT) | DMA_RX_ENABLE);
- hw->rx_cfg |= KS884X_DMA_RX_MULTICAST;
-
- /* Hardware cannot handle UDP packet in IP fragments. */
- hw->rx_cfg |= (DMA_RX_CSUM_TCP | DMA_RX_CSUM_IP);
-
- if (hw->all_multi)
- hw->rx_cfg |= DMA_RX_ALL_MULTICAST;
- if (hw->promiscuous)
- hw->rx_cfg |= DMA_RX_PROMISCUOUS;
-}
-
-/**
- * hw_setup_intr - setup interrupt mask
- * @hw: The hardware instance.
- *
- * This routine setup the interrupt mask for proper operation.
- */
-static void hw_setup_intr(struct ksz_hw *hw)
-{
- hw->intr_mask = KS884X_INT_MASK | KS884X_INT_RX_OVERRUN;
-}
-
-static void ksz_check_desc_num(struct ksz_desc_info *info)
-{
-#define MIN_DESC_SHIFT 2
-
- int alloc = info->alloc;
- int shift;
-
- shift = 0;
- while (!(alloc & 1)) {
- shift++;
- alloc >>= 1;
- }
- if (alloc != 1 || shift < MIN_DESC_SHIFT) {
- pr_alert("Hardware descriptor numbers not right!\n");
- while (alloc) {
- shift++;
- alloc >>= 1;
- }
- if (shift < MIN_DESC_SHIFT)
- shift = MIN_DESC_SHIFT;
- alloc = 1 << shift;
- info->alloc = alloc;
- }
- info->mask = info->alloc - 1;
-}
-
-static void hw_init_desc(struct ksz_desc_info *desc_info, int transmit)
-{
- int i;
- u32 phys = desc_info->ring_phys;
- struct ksz_hw_desc *desc = desc_info->ring_virt;
- struct ksz_desc *cur = desc_info->ring;
- struct ksz_desc *previous = NULL;
-
- for (i = 0; i < desc_info->alloc; i++) {
- cur->phw = desc++;
- phys += desc_info->size;
- previous = cur++;
- previous->phw->next = cpu_to_le32(phys);
- }
- previous->phw->next = cpu_to_le32(desc_info->ring_phys);
- previous->sw.buf.rx.end_of_ring = 1;
- previous->phw->buf.data = cpu_to_le32(previous->sw.buf.data);
-
- desc_info->avail = desc_info->alloc;
- desc_info->last = desc_info->next = 0;
-
- desc_info->cur = desc_info->ring;
-}
-
-/**
- * hw_set_desc_base - set descriptor base addresses
- * @hw: The hardware instance.
- * @tx_addr: The transmit descriptor base.
- * @rx_addr: The receive descriptor base.
- *
- * This routine programs the descriptor base addresses after reset.
- */
-static void hw_set_desc_base(struct ksz_hw *hw, u32 tx_addr, u32 rx_addr)
-{
- /* Set base address of Tx/Rx descriptors. */
- writel(tx_addr, hw->io + KS_DMA_TX_ADDR);
- writel(rx_addr, hw->io + KS_DMA_RX_ADDR);
-}
-
-static void hw_reset_pkts(struct ksz_desc_info *info)
-{
- info->cur = info->ring;
- info->avail = info->alloc;
- info->last = info->next = 0;
-}
-
-static inline void hw_resume_rx(struct ksz_hw *hw)
-{
- writel(DMA_START, hw->io + KS_DMA_RX_START);
-}
-
-/**
- * hw_start_rx - start receiving
- * @hw: The hardware instance.
- *
- * This routine starts the receive function of the hardware.
- */
-static void hw_start_rx(struct ksz_hw *hw)
-{
- writel(hw->rx_cfg, hw->io + KS_DMA_RX_CTRL);
-
- /* Notify when the receive stops. */
- hw->intr_mask |= KS884X_INT_RX_STOPPED;
-
- writel(DMA_START, hw->io + KS_DMA_RX_START);
- hw_ack_intr(hw, KS884X_INT_RX_STOPPED);
- hw->rx_stop++;
-
- /* Variable overflows. */
- if (0 == hw->rx_stop)
- hw->rx_stop = 2;
-}
-
-/*
- * hw_stop_rx - stop receiving
- * @hw: The hardware instance.
- *
- * This routine stops the receive function of the hardware.
- */
-static void hw_stop_rx(struct ksz_hw *hw)
-{
- hw->rx_stop = 0;
- hw_turn_off_intr(hw, KS884X_INT_RX_STOPPED);
- writel((hw->rx_cfg & ~DMA_RX_ENABLE), hw->io + KS_DMA_RX_CTRL);
-}
-
-/**
- * hw_start_tx - start transmitting
- * @hw: The hardware instance.
- *
- * This routine starts the transmit function of the hardware.
- */
-static void hw_start_tx(struct ksz_hw *hw)
-{
- writel(hw->tx_cfg, hw->io + KS_DMA_TX_CTRL);
-}
-
-/**
- * hw_stop_tx - stop transmitting
- * @hw: The hardware instance.
- *
- * This routine stops the transmit function of the hardware.
- */
-static void hw_stop_tx(struct ksz_hw *hw)
-{
- writel((hw->tx_cfg & ~DMA_TX_ENABLE), hw->io + KS_DMA_TX_CTRL);
-}
-
-/**
- * hw_disable - disable hardware
- * @hw: The hardware instance.
- *
- * This routine disables the hardware.
- */
-static void hw_disable(struct ksz_hw *hw)
-{
- hw_stop_rx(hw);
- hw_stop_tx(hw);
- hw->enabled = 0;
-}
-
-/**
- * hw_enable - enable hardware
- * @hw: The hardware instance.
- *
- * This routine enables the hardware.
- */
-static void hw_enable(struct ksz_hw *hw)
-{
- hw_start_tx(hw);
- hw_start_rx(hw);
- hw->enabled = 1;
-}
-
-/**
- * hw_alloc_pkt - allocate enough descriptors for transmission
- * @hw: The hardware instance.
- * @length: The length of the packet.
- * @physical: Number of descriptors required.
- *
- * This function allocates descriptors for transmission.
- *
- * Return 0 if not successful; 1 for buffer copy; or number of descriptors.
- */
-static int hw_alloc_pkt(struct ksz_hw *hw, int length, int physical)
-{
- /* Always leave one descriptor free. */
- if (hw->tx_desc_info.avail <= 1)
- return 0;
-
- /* Allocate a descriptor for transmission and mark it current. */
- get_tx_pkt(&hw->tx_desc_info, &hw->tx_desc_info.cur);
- hw->tx_desc_info.cur->sw.buf.tx.first_seg = 1;
-
- /* Keep track of number of transmit descriptors used so far. */
- ++hw->tx_int_cnt;
- hw->tx_size += length;
-
- /* Cannot hold on too much data. */
- if (hw->tx_size >= MAX_TX_HELD_SIZE)
- hw->tx_int_cnt = hw->tx_int_mask + 1;
-
- if (physical > hw->tx_desc_info.avail)
- return 1;
-
- return hw->tx_desc_info.avail;
-}
-
-/**
- * hw_send_pkt - mark packet for transmission
- * @hw: The hardware instance.
- *
- * This routine marks the packet for transmission in PCI version.
- */
-static void hw_send_pkt(struct ksz_hw *hw)
-{
- struct ksz_desc *cur = hw->tx_desc_info.cur;
-
- cur->sw.buf.tx.last_seg = 1;
-
- /* Interrupt only after specified number of descriptors used. */
- if (hw->tx_int_cnt > hw->tx_int_mask) {
- cur->sw.buf.tx.intr = 1;
- hw->tx_int_cnt = 0;
- hw->tx_size = 0;
- }
-
- /* KSZ8842 supports port directed transmission. */
- cur->sw.buf.tx.dest_port = hw->dst_ports;
-
- release_desc(cur);
-
- writel(0, hw->io + KS_DMA_TX_START);
-}
-
-static int empty_addr(u8 *addr)
-{
- u32 *addr1 = (u32 *) addr;
- u16 *addr2 = (u16 *) &addr[4];
-
- return 0 == *addr1 && 0 == *addr2;
-}
-
-/**
- * hw_set_addr - set MAC address
- * @hw: The hardware instance.
- *
- * This routine programs the MAC address of the hardware when the address is
- * overrided.
- */
-static void hw_set_addr(struct ksz_hw *hw)
-{
- int i;
-
- for (i = 0; i < MAC_ADDR_LEN; i++)
- writeb(hw->override_addr[MAC_ADDR_ORDER(i)],
- hw->io + KS884X_ADDR_0_OFFSET + i);
-
- sw_set_addr(hw, hw->override_addr);
-}
-
-/**
- * hw_read_addr - read MAC address
- * @hw: The hardware instance.
- *
- * This routine retrieves the MAC address of the hardware.
- */
-static void hw_read_addr(struct ksz_hw *hw)
-{
- int i;
-
- for (i = 0; i < MAC_ADDR_LEN; i++)
- hw->perm_addr[MAC_ADDR_ORDER(i)] = readb(hw->io +
- KS884X_ADDR_0_OFFSET + i);
-
- if (!hw->mac_override) {
- memcpy(hw->override_addr, hw->perm_addr, MAC_ADDR_LEN);
- if (empty_addr(hw->override_addr)) {
- memcpy(hw->perm_addr, DEFAULT_MAC_ADDRESS,
- MAC_ADDR_LEN);
- memcpy(hw->override_addr, DEFAULT_MAC_ADDRESS,
- MAC_ADDR_LEN);
- hw->override_addr[5] += hw->id;
- hw_set_addr(hw);
- }
- }
-}
-
-static void hw_ena_add_addr(struct ksz_hw *hw, int index, u8 *mac_addr)
-{
- int i;
- u32 mac_addr_lo;
- u32 mac_addr_hi;
-
- mac_addr_hi = 0;
- for (i = 0; i < 2; i++) {
- mac_addr_hi <<= 8;
- mac_addr_hi |= mac_addr[i];
- }
- mac_addr_hi |= ADD_ADDR_ENABLE;
- mac_addr_lo = 0;
- for (i = 2; i < 6; i++) {
- mac_addr_lo <<= 8;
- mac_addr_lo |= mac_addr[i];
- }
- index *= ADD_ADDR_INCR;
-
- writel(mac_addr_lo, hw->io + index + KS_ADD_ADDR_0_LO);
- writel(mac_addr_hi, hw->io + index + KS_ADD_ADDR_0_HI);
-}
-
-static void hw_set_add_addr(struct ksz_hw *hw)
-{
- int i;
-
- for (i = 0; i < ADDITIONAL_ENTRIES; i++) {
- if (empty_addr(hw->address[i]))
- writel(0, hw->io + ADD_ADDR_INCR * i +
- KS_ADD_ADDR_0_HI);
- else
- hw_ena_add_addr(hw, i, hw->address[i]);
- }
-}
-
-static int hw_add_addr(struct ksz_hw *hw, u8 *mac_addr)
-{
- int i;
- int j = ADDITIONAL_ENTRIES;
-
- if (!memcmp(hw->override_addr, mac_addr, MAC_ADDR_LEN))
- return 0;
- for (i = 0; i < hw->addr_list_size; i++) {
- if (!memcmp(hw->address[i], mac_addr, MAC_ADDR_LEN))
- return 0;
- if (ADDITIONAL_ENTRIES == j && empty_addr(hw->address[i]))
- j = i;
- }
- if (j < ADDITIONAL_ENTRIES) {
- memcpy(hw->address[j], mac_addr, MAC_ADDR_LEN);
- hw_ena_add_addr(hw, j, hw->address[j]);
- return 0;
- }
- return -1;
-}
-
-static int hw_del_addr(struct ksz_hw *hw, u8 *mac_addr)
-{
- int i;
-
- for (i = 0; i < hw->addr_list_size; i++) {
- if (!memcmp(hw->address[i], mac_addr, MAC_ADDR_LEN)) {
- memset(hw->address[i], 0, MAC_ADDR_LEN);
- writel(0, hw->io + ADD_ADDR_INCR * i +
- KS_ADD_ADDR_0_HI);
- return 0;
- }
- }
- return -1;
-}
-
-/**
- * hw_clr_multicast - clear multicast addresses
- * @hw: The hardware instance.
- *
- * This routine removes all multicast addresses set in the hardware.
- */
-static void hw_clr_multicast(struct ksz_hw *hw)
-{
- int i;
-
- for (i = 0; i < HW_MULTICAST_SIZE; i++) {
- hw->multi_bits[i] = 0;
-
- writeb(0, hw->io + KS884X_MULTICAST_0_OFFSET + i);
- }
-}
-
-/**
- * hw_set_grp_addr - set multicast addresses
- * @hw: The hardware instance.
- *
- * This routine programs multicast addresses for the hardware to accept those
- * addresses.
- */
-static void hw_set_grp_addr(struct ksz_hw *hw)
-{
- int i;
- int index;
- int position;
- int value;
-
- memset(hw->multi_bits, 0, sizeof(u8) * HW_MULTICAST_SIZE);
-
- for (i = 0; i < hw->multi_list_size; i++) {
- position = (ether_crc(6, hw->multi_list[i]) >> 26) & 0x3f;
- index = position >> 3;
- value = 1 << (position & 7);
- hw->multi_bits[index] |= (u8) value;
- }
-
- for (i = 0; i < HW_MULTICAST_SIZE; i++)
- writeb(hw->multi_bits[i], hw->io + KS884X_MULTICAST_0_OFFSET +
- i);
-}
-
-/**
- * hw_set_multicast - enable or disable all multicast receiving
- * @hw: The hardware instance.
- * @multicast: To turn on or off the all multicast feature.
- *
- * This routine enables/disables the hardware to accept all multicast packets.
- */
-static void hw_set_multicast(struct ksz_hw *hw, u8 multicast)
-{
- /* Stop receiving for reconfiguration. */
- hw_stop_rx(hw);
-
- if (multicast)
- hw->rx_cfg |= DMA_RX_ALL_MULTICAST;
- else
- hw->rx_cfg &= ~DMA_RX_ALL_MULTICAST;
-
- if (hw->enabled)
- hw_start_rx(hw);
-}
-
-/**
- * hw_set_promiscuous - enable or disable promiscuous receiving
- * @hw: The hardware instance.
- * @prom: To turn on or off the promiscuous feature.
- *
- * This routine enables/disables the hardware to accept all packets.
- */
-static void hw_set_promiscuous(struct ksz_hw *hw, u8 prom)
-{
- /* Stop receiving for reconfiguration. */
- hw_stop_rx(hw);
-
- if (prom)
- hw->rx_cfg |= DMA_RX_PROMISCUOUS;
- else
- hw->rx_cfg &= ~DMA_RX_PROMISCUOUS;
-
- if (hw->enabled)
- hw_start_rx(hw);
-}
-
-/**
- * sw_enable - enable the switch
- * @hw: The hardware instance.
- * @enable: The flag to enable or disable the switch
- *
- * This routine is used to enable/disable the switch in KSZ8842.
- */
-static void sw_enable(struct ksz_hw *hw, int enable)
-{
- int port;
-
- for (port = 0; port < SWITCH_PORT_NUM; port++) {
- if (hw->dev_count > 1) {
- /* Set port-base vlan membership with host port. */
- sw_cfg_port_base_vlan(hw, port,
- HOST_MASK | (1 << port));
- port_set_stp_state(hw, port, STP_STATE_DISABLED);
- } else {
- sw_cfg_port_base_vlan(hw, port, PORT_MASK);
- port_set_stp_state(hw, port, STP_STATE_FORWARDING);
- }
- }
- if (hw->dev_count > 1)
- port_set_stp_state(hw, SWITCH_PORT_NUM, STP_STATE_SIMPLE);
- else
- port_set_stp_state(hw, SWITCH_PORT_NUM, STP_STATE_FORWARDING);
-
- if (enable)
- enable = KS8842_START;
- writew(enable, hw->io + KS884X_CHIP_ID_OFFSET);
-}
-
-/**
- * sw_setup - setup the switch
- * @hw: The hardware instance.
- *
- * This routine setup the hardware switch engine for default operation.
- */
-static void sw_setup(struct ksz_hw *hw)
-{
- int port;
-
- sw_set_global_ctrl(hw);
-
- /* Enable switch broadcast storm protection at 10% percent rate. */
- sw_init_broad_storm(hw);
- hw_cfg_broad_storm(hw, BROADCAST_STORM_PROTECTION_RATE);
- for (port = 0; port < SWITCH_PORT_NUM; port++)
- sw_ena_broad_storm(hw, port);
-
- sw_init_prio(hw);
-
- sw_init_mirror(hw);
-
- sw_init_prio_rate(hw);
-
- sw_init_vlan(hw);
-
- if (hw->features & STP_SUPPORT)
- sw_init_stp(hw);
- if (!sw_chk(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_TX_FLOW_CTRL | SWITCH_RX_FLOW_CTRL))
- hw->overrides |= PAUSE_FLOW_CTRL;
- sw_enable(hw, 1);
-}
-
-/**
- * ksz_start_timer - start kernel timer
- * @info: Kernel timer information.
- * @time: The time tick.
- *
- * This routine starts the kernel timer after the specified time tick.
- */
-static void ksz_start_timer(struct ksz_timer_info *info, int time)
-{
- info->cnt = 0;
- info->timer.expires = jiffies + time;
- add_timer(&info->timer);
-
- /* infinity */
- info->max = -1;
-}
-
-/**
- * ksz_stop_timer - stop kernel timer
- * @info: Kernel timer information.
- *
- * This routine stops the kernel timer.
- */
-static void ksz_stop_timer(struct ksz_timer_info *info)
-{
- if (info->max) {
- info->max = 0;
- del_timer_sync(&info->timer);
- }
-}
-
-static void ksz_init_timer(struct ksz_timer_info *info, int period,
- void (*function)(unsigned long), void *data)
-{
- info->max = 0;
- info->period = period;
- init_timer(&info->timer);
- info->timer.function = function;
- info->timer.data = (unsigned long) data;
-}
-
-static void ksz_update_timer(struct ksz_timer_info *info)
-{
- ++info->cnt;
- if (info->max > 0) {
- if (info->cnt < info->max) {
- info->timer.expires = jiffies + info->period;
- add_timer(&info->timer);
- } else
- info->max = 0;
- } else if (info->max < 0) {
- info->timer.expires = jiffies + info->period;
- add_timer(&info->timer);
- }
-}
-
-/**
- * ksz_alloc_soft_desc - allocate software descriptors
- * @desc_info: Descriptor information structure.
- * @transmit: Indication that descriptors are for transmit.
- *
- * This local function allocates software descriptors for manipulation in
- * memory.
- *
- * Return 0 if successful.
- */
-static int ksz_alloc_soft_desc(struct ksz_desc_info *desc_info, int transmit)
-{
- desc_info->ring = kmalloc(sizeof(struct ksz_desc) * desc_info->alloc,
- GFP_KERNEL);
- if (!desc_info->ring)
- return 1;
- memset((void *) desc_info->ring, 0,
- sizeof(struct ksz_desc) * desc_info->alloc);
- hw_init_desc(desc_info, transmit);
- return 0;
-}
-
-/**
- * ksz_alloc_desc - allocate hardware descriptors
- * @adapter: Adapter information structure.
- *
- * This local function allocates hardware descriptors for receiving and
- * transmitting.
- *
- * Return 0 if successful.
- */
-static int ksz_alloc_desc(struct dev_info *adapter)
-{
- struct ksz_hw *hw = &adapter->hw;
- int offset;
-
- /* Allocate memory for RX & TX descriptors. */
- adapter->desc_pool.alloc_size =
- hw->rx_desc_info.size * hw->rx_desc_info.alloc +
- hw->tx_desc_info.size * hw->tx_desc_info.alloc +
- DESC_ALIGNMENT;
-
- adapter->desc_pool.alloc_virt =
- pci_alloc_consistent(
- adapter->pdev, adapter->desc_pool.alloc_size,
- &adapter->desc_pool.dma_addr);
- if (adapter->desc_pool.alloc_virt == NULL) {
- adapter->desc_pool.alloc_size = 0;
- return 1;
- }
- memset(adapter->desc_pool.alloc_virt, 0, adapter->desc_pool.alloc_size);
-
- /* Align to the next cache line boundary. */
- offset = (((ulong) adapter->desc_pool.alloc_virt % DESC_ALIGNMENT) ?
- (DESC_ALIGNMENT -
- ((ulong) adapter->desc_pool.alloc_virt % DESC_ALIGNMENT)) : 0);
- adapter->desc_pool.virt = adapter->desc_pool.alloc_virt + offset;
- adapter->desc_pool.phys = adapter->desc_pool.dma_addr + offset;
-
- /* Allocate receive/transmit descriptors. */
- hw->rx_desc_info.ring_virt = (struct ksz_hw_desc *)
- adapter->desc_pool.virt;
- hw->rx_desc_info.ring_phys = adapter->desc_pool.phys;
- offset = hw->rx_desc_info.alloc * hw->rx_desc_info.size;
- hw->tx_desc_info.ring_virt = (struct ksz_hw_desc *)
- (adapter->desc_pool.virt + offset);
- hw->tx_desc_info.ring_phys = adapter->desc_pool.phys + offset;
-
- if (ksz_alloc_soft_desc(&hw->rx_desc_info, 0))
- return 1;
- if (ksz_alloc_soft_desc(&hw->tx_desc_info, 1))
- return 1;
-
- return 0;
-}
-
-/**
- * free_dma_buf - release DMA buffer resources
- * @adapter: Adapter information structure.
- *
- * This routine is just a helper function to release the DMA buffer resources.
- */
-static void free_dma_buf(struct dev_info *adapter, struct ksz_dma_buf *dma_buf,
- int direction)
-{
- pci_unmap_single(adapter->pdev, dma_buf->dma, dma_buf->len, direction);
- dev_kfree_skb(dma_buf->skb);
- dma_buf->skb = NULL;
- dma_buf->dma = 0;
-}
-
-/**
- * ksz_init_rx_buffers - initialize receive descriptors
- * @adapter: Adapter information structure.
- *
- * This routine initializes DMA buffers for receiving.
- */
-static void ksz_init_rx_buffers(struct dev_info *adapter)
-{
- int i;
- struct ksz_desc *desc;
- struct ksz_dma_buf *dma_buf;
- struct ksz_hw *hw = &adapter->hw;
- struct ksz_desc_info *info = &hw->rx_desc_info;
-
- for (i = 0; i < hw->rx_desc_info.alloc; i++) {
- get_rx_pkt(info, &desc);
-
- dma_buf = DMA_BUFFER(desc);
- if (dma_buf->skb && dma_buf->len != adapter->mtu)
- free_dma_buf(adapter, dma_buf, PCI_DMA_FROMDEVICE);
- dma_buf->len = adapter->mtu;
- if (!dma_buf->skb)
- dma_buf->skb = alloc_skb(dma_buf->len, GFP_ATOMIC);
- if (dma_buf->skb && !dma_buf->dma) {
- dma_buf->skb->dev = adapter->dev;
- dma_buf->dma = pci_map_single(
- adapter->pdev,
- skb_tail_pointer(dma_buf->skb),
- dma_buf->len,
- PCI_DMA_FROMDEVICE);
- }
-
- /* Set descriptor. */
- set_rx_buf(desc, dma_buf->dma);
- set_rx_len(desc, dma_buf->len);
- release_desc(desc);
- }
-}
-
-/**
- * ksz_alloc_mem - allocate memory for hardware descriptors
- * @adapter: Adapter information structure.
- *
- * This function allocates memory for use by hardware descriptors for receiving
- * and transmitting.
- *
- * Return 0 if successful.
- */
-static int ksz_alloc_mem(struct dev_info *adapter)
-{
- struct ksz_hw *hw = &adapter->hw;
-
- /* Determine the number of receive and transmit descriptors. */
- hw->rx_desc_info.alloc = NUM_OF_RX_DESC;
- hw->tx_desc_info.alloc = NUM_OF_TX_DESC;
-
- /* Determine how many descriptors to skip transmit interrupt. */
- hw->tx_int_cnt = 0;
- hw->tx_int_mask = NUM_OF_TX_DESC / 4;
- if (hw->tx_int_mask > 8)
- hw->tx_int_mask = 8;
- while (hw->tx_int_mask) {
- hw->tx_int_cnt++;
- hw->tx_int_mask >>= 1;
- }
- if (hw->tx_int_cnt) {
- hw->tx_int_mask = (1 << (hw->tx_int_cnt - 1)) - 1;
- hw->tx_int_cnt = 0;
- }
-
- /* Determine the descriptor size. */
- hw->rx_desc_info.size =
- (((sizeof(struct ksz_hw_desc) + DESC_ALIGNMENT - 1) /
- DESC_ALIGNMENT) * DESC_ALIGNMENT);
- hw->tx_desc_info.size =
- (((sizeof(struct ksz_hw_desc) + DESC_ALIGNMENT - 1) /
- DESC_ALIGNMENT) * DESC_ALIGNMENT);
- if (hw->rx_desc_info.size != sizeof(struct ksz_hw_desc))
- pr_alert("Hardware descriptor size not right!\n");
- ksz_check_desc_num(&hw->rx_desc_info);
- ksz_check_desc_num(&hw->tx_desc_info);
-
- /* Allocate descriptors. */
- if (ksz_alloc_desc(adapter))
- return 1;
-
- return 0;
-}
-
-/**
- * ksz_free_desc - free software and hardware descriptors
- * @adapter: Adapter information structure.
- *
- * This local routine frees the software and hardware descriptors allocated by
- * ksz_alloc_desc().
- */
-static void ksz_free_desc(struct dev_info *adapter)
-{
- struct ksz_hw *hw = &adapter->hw;
-
- /* Reset descriptor. */
- hw->rx_desc_info.ring_virt = NULL;
- hw->tx_desc_info.ring_virt = NULL;
- hw->rx_desc_info.ring_phys = 0;
- hw->tx_desc_info.ring_phys = 0;
-
- /* Free memory. */
- if (adapter->desc_pool.alloc_virt)
- pci_free_consistent(
- adapter->pdev,
- adapter->desc_pool.alloc_size,
- adapter->desc_pool.alloc_virt,
- adapter->desc_pool.dma_addr);
-
- /* Reset resource pool. */
- adapter->desc_pool.alloc_size = 0;
- adapter->desc_pool.alloc_virt = NULL;
-
- kfree(hw->rx_desc_info.ring);
- hw->rx_desc_info.ring = NULL;
- kfree(hw->tx_desc_info.ring);
- hw->tx_desc_info.ring = NULL;
-}
-
-/**
- * ksz_free_buffers - free buffers used in the descriptors
- * @adapter: Adapter information structure.
- * @desc_info: Descriptor information structure.
- *
- * This local routine frees buffers used in the DMA buffers.
- */
-static void ksz_free_buffers(struct dev_info *adapter,
- struct ksz_desc_info *desc_info, int direction)
-{
- int i;
- struct ksz_dma_buf *dma_buf;
- struct ksz_desc *desc = desc_info->ring;
-
- for (i = 0; i < desc_info->alloc; i++) {
- dma_buf = DMA_BUFFER(desc);
- if (dma_buf->skb)
- free_dma_buf(adapter, dma_buf, direction);
- desc++;
- }
-}
-
-/**
- * ksz_free_mem - free all resources used by descriptors
- * @adapter: Adapter information structure.
- *
- * This local routine frees all the resources allocated by ksz_alloc_mem().
- */
-static void ksz_free_mem(struct dev_info *adapter)
-{
- /* Free transmit buffers. */
- ksz_free_buffers(adapter, &adapter->hw.tx_desc_info,
- PCI_DMA_TODEVICE);
-
- /* Free receive buffers. */
- ksz_free_buffers(adapter, &adapter->hw.rx_desc_info,
- PCI_DMA_FROMDEVICE);
-
- /* Free descriptors. */
- ksz_free_desc(adapter);
-}
-
-static void get_mib_counters(struct ksz_hw *hw, int first, int cnt,
- u64 *counter)
-{
- int i;
- int mib;
- int port;
- struct ksz_port_mib *port_mib;
-
- memset(counter, 0, sizeof(u64) * TOTAL_PORT_COUNTER_NUM);
- for (i = 0, port = first; i < cnt; i++, port++) {
- port_mib = &hw->port_mib[port];
- for (mib = port_mib->mib_start; mib < hw->mib_cnt; mib++)
- counter[mib] += port_mib->counter[mib];
- }
-}
-
-/**
- * send_packet - send packet
- * @skb: Socket buffer.
- * @dev: Network device.
- *
- * This routine is used to send a packet out to the network.
- */
-static void send_packet(struct sk_buff *skb, struct net_device *dev)
-{
- struct ksz_desc *desc;
- struct ksz_desc *first;
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_desc_info *info = &hw->tx_desc_info;
- struct ksz_dma_buf *dma_buf;
- int len;
- int last_frag = skb_shinfo(skb)->nr_frags;
-
- /*
- * KSZ8842 with multiple device interfaces needs to be told which port
- * to send.
- */
- if (hw->dev_count > 1)
- hw->dst_ports = 1 << priv->port.first_port;
-
- /* Hardware will pad the length to 60. */
- len = skb->len;
-
- /* Remember the very first descriptor. */
- first = info->cur;
- desc = first;
-
- dma_buf = DMA_BUFFER(desc);
- if (last_frag) {
- int frag;
- skb_frag_t *this_frag;
-
- dma_buf->len = skb_headlen(skb);
-
- dma_buf->dma = pci_map_single(
- hw_priv->pdev, skb->data, dma_buf->len,
- PCI_DMA_TODEVICE);
- set_tx_buf(desc, dma_buf->dma);
- set_tx_len(desc, dma_buf->len);
-
- frag = 0;
- do {
- this_frag = &skb_shinfo(skb)->frags[frag];
-
- /* Get a new descriptor. */
- get_tx_pkt(info, &desc);
-
- /* Keep track of descriptors used so far. */
- ++hw->tx_int_cnt;
-
- dma_buf = DMA_BUFFER(desc);
- dma_buf->len = this_frag->size;
-
- dma_buf->dma = pci_map_single(
- hw_priv->pdev,
- page_address(this_frag->page) +
- this_frag->page_offset,
- dma_buf->len,
- PCI_DMA_TODEVICE);
- set_tx_buf(desc, dma_buf->dma);
- set_tx_len(desc, dma_buf->len);
-
- frag++;
- if (frag == last_frag)
- break;
-
- /* Do not release the last descriptor here. */
- release_desc(desc);
- } while (1);
-
- /* current points to the last descriptor. */
- info->cur = desc;
-
- /* Release the first descriptor. */
- release_desc(first);
- } else {
- dma_buf->len = len;
-
- dma_buf->dma = pci_map_single(
- hw_priv->pdev, skb->data, dma_buf->len,
- PCI_DMA_TODEVICE);
- set_tx_buf(desc, dma_buf->dma);
- set_tx_len(desc, dma_buf->len);
- }
-
- if (skb->ip_summed == CHECKSUM_PARTIAL) {
- (desc)->sw.buf.tx.csum_gen_tcp = 1;
- (desc)->sw.buf.tx.csum_gen_udp = 1;
- }
-
- /*
- * The last descriptor holds the packet so that it can be returned to
- * network subsystem after all descriptors are transmitted.
- */
- dma_buf->skb = skb;
-
- hw_send_pkt(hw);
-
- /* Update transmit statistics. */
- dev->stats.tx_packets++;
- dev->stats.tx_bytes += len;
-}
-
-/**
- * transmit_cleanup - clean up transmit descriptors
- * @dev: Network device.
- *
- * This routine is called to clean up the transmitted buffers.
- */
-static void transmit_cleanup(struct dev_info *hw_priv, int normal)
-{
- int last;
- union desc_stat status;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_desc_info *info = &hw->tx_desc_info;
- struct ksz_desc *desc;
- struct ksz_dma_buf *dma_buf;
- struct net_device *dev = NULL;
-
- spin_lock(&hw_priv->hwlock);
- last = info->last;
-
- while (info->avail < info->alloc) {
- /* Get next descriptor which is not hardware owned. */
- desc = &info->ring[last];
- status.data = le32_to_cpu(desc->phw->ctrl.data);
- if (status.tx.hw_owned) {
- if (normal)
- break;
- else
- reset_desc(desc, status);
- }
-
- dma_buf = DMA_BUFFER(desc);
- pci_unmap_single(
- hw_priv->pdev, dma_buf->dma, dma_buf->len,
- PCI_DMA_TODEVICE);
-
- /* This descriptor contains the last buffer in the packet. */
- if (dma_buf->skb) {
- dev = dma_buf->skb->dev;
-
- /* Release the packet back to network subsystem. */
- dev_kfree_skb_irq(dma_buf->skb);
- dma_buf->skb = NULL;
- }
-
- /* Free the transmitted descriptor. */
- last++;
- last &= info->mask;
- info->avail++;
- }
- info->last = last;
- spin_unlock(&hw_priv->hwlock);
-
- /* Notify the network subsystem that the packet has been sent. */
- if (dev)
- dev->trans_start = jiffies;
-}
-
-/**
- * transmit_done - transmit done processing
- * @dev: Network device.
- *
- * This routine is called when the transmit interrupt is triggered, indicating
- * either a packet is sent successfully or there are transmit errors.
- */
-static void tx_done(struct dev_info *hw_priv)
-{
- struct ksz_hw *hw = &hw_priv->hw;
- int port;
-
- transmit_cleanup(hw_priv, 1);
-
- for (port = 0; port < hw->dev_count; port++) {
- struct net_device *dev = hw->port_info[port].pdev;
-
- if (netif_running(dev) && netif_queue_stopped(dev))
- netif_wake_queue(dev);
- }
-}
-
-static inline void copy_old_skb(struct sk_buff *old, struct sk_buff *skb)
-{
- skb->dev = old->dev;
- skb->protocol = old->protocol;
- skb->ip_summed = old->ip_summed;
- skb->csum = old->csum;
- skb_set_network_header(skb, ETH_HLEN);
-
- dev_kfree_skb(old);
-}
-
-/**
- * netdev_tx - send out packet
- * @skb: Socket buffer.
- * @dev: Network device.
- *
- * This function is used by the upper network layer to send out a packet.
- *
- * Return 0 if successful; otherwise an error code indicating failure.
- */
-static netdev_tx_t netdev_tx(struct sk_buff *skb, struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- int left;
- int num = 1;
- int rc = 0;
-
- if (hw->features & SMALL_PACKET_TX_BUG) {
- struct sk_buff *org_skb = skb;
-
- if (skb->len <= 48) {
- if (skb_end_pointer(skb) - skb->data >= 50) {
- memset(&skb->data[skb->len], 0, 50 - skb->len);
- skb->len = 50;
- } else {
- skb = dev_alloc_skb(50);
- if (!skb)
- return NETDEV_TX_BUSY;
- memcpy(skb->data, org_skb->data, org_skb->len);
- memset(&skb->data[org_skb->len], 0,
- 50 - org_skb->len);
- skb->len = 50;
- copy_old_skb(org_skb, skb);
- }
- }
- }
-
- spin_lock_irq(&hw_priv->hwlock);
-
- num = skb_shinfo(skb)->nr_frags + 1;
- left = hw_alloc_pkt(hw, skb->len, num);
- if (left) {
- if (left < num ||
- ((CHECKSUM_PARTIAL == skb->ip_summed) &&
- (ETH_P_IPV6 == htons(skb->protocol)))) {
- struct sk_buff *org_skb = skb;
-
- skb = dev_alloc_skb(org_skb->len);
- if (!skb) {
- rc = NETDEV_TX_BUSY;
- goto unlock;
- }
- skb_copy_and_csum_dev(org_skb, skb->data);
- org_skb->ip_summed = CHECKSUM_NONE;
- skb->len = org_skb->len;
- copy_old_skb(org_skb, skb);
- }
- send_packet(skb, dev);
- if (left <= num)
- netif_stop_queue(dev);
- } else {
- /* Stop the transmit queue until packet is allocated. */
- netif_stop_queue(dev);
- rc = NETDEV_TX_BUSY;
- }
-unlock:
- spin_unlock_irq(&hw_priv->hwlock);
-
- return rc;
-}
-
-/**
- * netdev_tx_timeout - transmit timeout processing
- * @dev: Network device.
- *
- * This routine is called when the transmit timer expires. That indicates the
- * hardware is not running correctly because transmit interrupts are not
- * triggered to free up resources so that the transmit routine can continue
- * sending out packets. The hardware is reset to correct the problem.
- */
-static void netdev_tx_timeout(struct net_device *dev)
-{
- static unsigned long last_reset;
-
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- int port;
-
- if (hw->dev_count > 1) {
- /*
- * Only reset the hardware if time between calls is long
- * enough.
- */
- if (jiffies - last_reset <= dev->watchdog_timeo)
- hw_priv = NULL;
- }
-
- last_reset = jiffies;
- if (hw_priv) {
- hw_dis_intr(hw);
- hw_disable(hw);
-
- transmit_cleanup(hw_priv, 0);
- hw_reset_pkts(&hw->rx_desc_info);
- hw_reset_pkts(&hw->tx_desc_info);
- ksz_init_rx_buffers(hw_priv);
-
- hw_reset(hw);
-
- hw_set_desc_base(hw,
- hw->tx_desc_info.ring_phys,
- hw->rx_desc_info.ring_phys);
- hw_set_addr(hw);
- if (hw->all_multi)
- hw_set_multicast(hw, hw->all_multi);
- else if (hw->multi_list_size)
- hw_set_grp_addr(hw);
-
- if (hw->dev_count > 1) {
- hw_set_add_addr(hw);
- for (port = 0; port < SWITCH_PORT_NUM; port++) {
- struct net_device *port_dev;
-
- port_set_stp_state(hw, port,
- STP_STATE_DISABLED);
-
- port_dev = hw->port_info[port].pdev;
- if (netif_running(port_dev))
- port_set_stp_state(hw, port,
- STP_STATE_SIMPLE);
- }
- }
-
- hw_enable(hw);
- hw_ena_intr(hw);
- }
-
- dev->trans_start = jiffies;
- netif_wake_queue(dev);
-}
-
-static inline void csum_verified(struct sk_buff *skb)
-{
- unsigned short protocol;
- struct iphdr *iph;
-
- protocol = skb->protocol;
- skb_reset_network_header(skb);
- iph = (struct iphdr *) skb_network_header(skb);
- if (protocol == htons(ETH_P_8021Q)) {
- protocol = iph->tot_len;
- skb_set_network_header(skb, VLAN_HLEN);
- iph = (struct iphdr *) skb_network_header(skb);
- }
- if (protocol == htons(ETH_P_IP)) {
- if (iph->protocol == IPPROTO_TCP)
- skb->ip_summed = CHECKSUM_UNNECESSARY;
- }
-}
-
-static inline int rx_proc(struct net_device *dev, struct ksz_hw* hw,
- struct ksz_desc *desc, union desc_stat status)
-{
- int packet_len;
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_dma_buf *dma_buf;
- struct sk_buff *skb;
- int rx_status;
-
- /* Received length includes 4-byte CRC. */
- packet_len = status.rx.frame_len - 4;
-
- dma_buf = DMA_BUFFER(desc);
- pci_dma_sync_single_for_cpu(
- hw_priv->pdev, dma_buf->dma, packet_len + 4,
- PCI_DMA_FROMDEVICE);
-
- do {
- /* skb->data != skb->head */
- skb = dev_alloc_skb(packet_len + 2);
- if (!skb) {
- dev->stats.rx_dropped++;
- return -ENOMEM;
- }
-
- /*
- * Align socket buffer in 4-byte boundary for better
- * performance.
- */
- skb_reserve(skb, 2);
-
- memcpy(skb_put(skb, packet_len),
- dma_buf->skb->data, packet_len);
- } while (0);
-
- skb->protocol = eth_type_trans(skb, dev);
-
- if (hw->rx_cfg & (DMA_RX_CSUM_UDP | DMA_RX_CSUM_TCP))
- csum_verified(skb);
-
- /* Update receive statistics. */
- dev->stats.rx_packets++;
- dev->stats.rx_bytes += packet_len;
-
- /* Notify upper layer for received packet. */
- rx_status = netif_rx(skb);
-
- return 0;
-}
-
-static int dev_rcv_packets(struct dev_info *hw_priv)
-{
- int next;
- union desc_stat status;
- struct ksz_hw *hw = &hw_priv->hw;
- struct net_device *dev = hw->port_info[0].pdev;
- struct ksz_desc_info *info = &hw->rx_desc_info;
- int left = info->alloc;
- struct ksz_desc *desc;
- int received = 0;
-
- next = info->next;
- while (left--) {
- /* Get next descriptor which is not hardware owned. */
- desc = &info->ring[next];
- status.data = le32_to_cpu(desc->phw->ctrl.data);
- if (status.rx.hw_owned)
- break;
-
- /* Status valid only when last descriptor bit is set. */
- if (status.rx.last_desc && status.rx.first_desc) {
- if (rx_proc(dev, hw, desc, status))
- goto release_packet;
- received++;
- }
-
-release_packet:
- release_desc(desc);
- next++;
- next &= info->mask;
- }
- info->next = next;
-
- return received;
-}
-
-static int port_rcv_packets(struct dev_info *hw_priv)
-{
- int next;
- union desc_stat status;
- struct ksz_hw *hw = &hw_priv->hw;
- struct net_device *dev = hw->port_info[0].pdev;
- struct ksz_desc_info *info = &hw->rx_desc_info;
- int left = info->alloc;
- struct ksz_desc *desc;
- int received = 0;
-
- next = info->next;
- while (left--) {
- /* Get next descriptor which is not hardware owned. */
- desc = &info->ring[next];
- status.data = le32_to_cpu(desc->phw->ctrl.data);
- if (status.rx.hw_owned)
- break;
-
- if (hw->dev_count > 1) {
- /* Get received port number. */
- int p = HW_TO_DEV_PORT(status.rx.src_port);
-
- dev = hw->port_info[p].pdev;
- if (!netif_running(dev))
- goto release_packet;
- }
-
- /* Status valid only when last descriptor bit is set. */
- if (status.rx.last_desc && status.rx.first_desc) {
- if (rx_proc(dev, hw, desc, status))
- goto release_packet;
- received++;
- }
-
-release_packet:
- release_desc(desc);
- next++;
- next &= info->mask;
- }
- info->next = next;
-
- return received;
-}
-
-static int dev_rcv_special(struct dev_info *hw_priv)
-{
- int next;
- union desc_stat status;
- struct ksz_hw *hw = &hw_priv->hw;
- struct net_device *dev = hw->port_info[0].pdev;
- struct ksz_desc_info *info = &hw->rx_desc_info;
- int left = info->alloc;
- struct ksz_desc *desc;
- int received = 0;
-
- next = info->next;
- while (left--) {
- /* Get next descriptor which is not hardware owned. */
- desc = &info->ring[next];
- status.data = le32_to_cpu(desc->phw->ctrl.data);
- if (status.rx.hw_owned)
- break;
-
- if (hw->dev_count > 1) {
- /* Get received port number. */
- int p = HW_TO_DEV_PORT(status.rx.src_port);
-
- dev = hw->port_info[p].pdev;
- if (!netif_running(dev))
- goto release_packet;
- }
-
- /* Status valid only when last descriptor bit is set. */
- if (status.rx.last_desc && status.rx.first_desc) {
- /*
- * Receive without error. With receive errors
- * disabled, packets with receive errors will be
- * dropped, so no need to check the error bit.
- */
- if (!status.rx.error || (status.data &
- KS_DESC_RX_ERROR_COND) ==
- KS_DESC_RX_ERROR_TOO_LONG) {
- if (rx_proc(dev, hw, desc, status))
- goto release_packet;
- received++;
- } else {
- struct dev_priv *priv = netdev_priv(dev);
-
- /* Update receive error statistics. */
- priv->port.counter[OID_COUNTER_RCV_ERROR]++;
- }
- }
-
-release_packet:
- release_desc(desc);
- next++;
- next &= info->mask;
- }
- info->next = next;
-
- return received;
-}
-
-static void rx_proc_task(unsigned long data)
-{
- struct dev_info *hw_priv = (struct dev_info *) data;
- struct ksz_hw *hw = &hw_priv->hw;
-
- if (!hw->enabled)
- return;
- if (unlikely(!hw_priv->dev_rcv(hw_priv))) {
-
- /* In case receive process is suspended because of overrun. */
- hw_resume_rx(hw);
-
- /* tasklets are interruptible. */
- spin_lock_irq(&hw_priv->hwlock);
- hw_turn_on_intr(hw, KS884X_INT_RX_MASK);
- spin_unlock_irq(&hw_priv->hwlock);
- } else {
- hw_ack_intr(hw, KS884X_INT_RX);
- tasklet_schedule(&hw_priv->rx_tasklet);
- }
-}
-
-static void tx_proc_task(unsigned long data)
-{
- struct dev_info *hw_priv = (struct dev_info *) data;
- struct ksz_hw *hw = &hw_priv->hw;
-
- hw_ack_intr(hw, KS884X_INT_TX_MASK);
-
- tx_done(hw_priv);
-
- /* tasklets are interruptible. */
- spin_lock_irq(&hw_priv->hwlock);
- hw_turn_on_intr(hw, KS884X_INT_TX);
- spin_unlock_irq(&hw_priv->hwlock);
-}
-
-static inline void handle_rx_stop(struct ksz_hw *hw)
-{
- /* Receive just has been stopped. */
- if (0 == hw->rx_stop)
- hw->intr_mask &= ~KS884X_INT_RX_STOPPED;
- else if (hw->rx_stop > 1) {
- if (hw->enabled && (hw->rx_cfg & DMA_RX_ENABLE)) {
- hw_start_rx(hw);
- } else {
- hw->intr_mask &= ~KS884X_INT_RX_STOPPED;
- hw->rx_stop = 0;
- }
- } else
- /* Receive just has been started. */
- hw->rx_stop++;
-}
-
-/**
- * netdev_intr - interrupt handling
- * @irq: Interrupt number.
- * @dev_id: Network device.
- *
- * This function is called by upper network layer to signal interrupt.
- *
- * Return IRQ_HANDLED if interrupt is handled.
- */
-static irqreturn_t netdev_intr(int irq, void *dev_id)
-{
- uint int_enable = 0;
- struct net_device *dev = (struct net_device *) dev_id;
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
-
- hw_read_intr(hw, &int_enable);
-
- /* Not our interrupt! */
- if (!int_enable)
- return IRQ_NONE;
-
- do {
- hw_ack_intr(hw, int_enable);
- int_enable &= hw->intr_mask;
-
- if (unlikely(int_enable & KS884X_INT_TX_MASK)) {
- hw_dis_intr_bit(hw, KS884X_INT_TX_MASK);
- tasklet_schedule(&hw_priv->tx_tasklet);
- }
-
- if (likely(int_enable & KS884X_INT_RX)) {
- hw_dis_intr_bit(hw, KS884X_INT_RX);
- tasklet_schedule(&hw_priv->rx_tasklet);
- }
-
- if (unlikely(int_enable & KS884X_INT_RX_OVERRUN)) {
- dev->stats.rx_fifo_errors++;
- hw_resume_rx(hw);
- }
-
- if (unlikely(int_enable & KS884X_INT_PHY)) {
- struct ksz_port *port = &priv->port;
-
- hw->features |= LINK_INT_WORKING;
- port_get_link_speed(port);
- }
-
- if (unlikely(int_enable & KS884X_INT_RX_STOPPED)) {
- handle_rx_stop(hw);
- break;
- }
-
- if (unlikely(int_enable & KS884X_INT_TX_STOPPED)) {
- u32 data;
-
- hw->intr_mask &= ~KS884X_INT_TX_STOPPED;
- pr_info("Tx stopped\n");
- data = readl(hw->io + KS_DMA_TX_CTRL);
- if (!(data & DMA_TX_ENABLE))
- pr_info("Tx disabled\n");
- break;
- }
- } while (0);
-
- hw_ena_intr(hw);
-
- return IRQ_HANDLED;
-}
-
-/*
- * Linux network device functions
- */
-
-static unsigned long next_jiffies;
-
-#ifdef CONFIG_NET_POLL_CONTROLLER
-static void netdev_netpoll(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
-
- hw_dis_intr(&hw_priv->hw);
- netdev_intr(dev->irq, dev);
-}
-#endif
-
-static void bridge_change(struct ksz_hw *hw)
-{
- int port;
- u8 member;
- struct ksz_switch *sw = hw->ksz_switch;
-
- /* No ports in forwarding state. */
- if (!sw->member) {
- port_set_stp_state(hw, SWITCH_PORT_NUM, STP_STATE_SIMPLE);
- sw_block_addr(hw);
- }
- for (port = 0; port < SWITCH_PORT_NUM; port++) {
- if (STP_STATE_FORWARDING == sw->port_cfg[port].stp_state)
- member = HOST_MASK | sw->member;
- else
- member = HOST_MASK | (1 << port);
- if (member != sw->port_cfg[port].member)
- sw_cfg_port_base_vlan(hw, port, member);
- }
-}
-
-/**
- * netdev_close - close network device
- * @dev: Network device.
- *
- * This function process the close operation of network device. This is caused
- * by the user command "ifconfig ethX down."
- *
- * Return 0 if successful; otherwise an error code indicating failure.
- */
-static int netdev_close(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_port *port = &priv->port;
- struct ksz_hw *hw = &hw_priv->hw;
- int pi;
-
- netif_stop_queue(dev);
-
- ksz_stop_timer(&priv->monitor_timer_info);
-
- /* Need to shut the port manually in multiple device interfaces mode. */
- if (hw->dev_count > 1) {
- port_set_stp_state(hw, port->first_port, STP_STATE_DISABLED);
-
- /* Port is closed. Need to change bridge setting. */
- if (hw->features & STP_SUPPORT) {
- pi = 1 << port->first_port;
- if (hw->ksz_switch->member & pi) {
- hw->ksz_switch->member &= ~pi;
- bridge_change(hw);
- }
- }
- }
- if (port->first_port > 0)
- hw_del_addr(hw, dev->dev_addr);
- if (!hw_priv->wol_enable)
- port_set_power_saving(port, true);
-
- if (priv->multicast)
- --hw->all_multi;
- if (priv->promiscuous)
- --hw->promiscuous;
-
- hw_priv->opened--;
- if (!(hw_priv->opened)) {
- ksz_stop_timer(&hw_priv->mib_timer_info);
- flush_work(&hw_priv->mib_read);
-
- hw_dis_intr(hw);
- hw_disable(hw);
- hw_clr_multicast(hw);
-
- /* Delay for receive task to stop scheduling itself. */
- msleep(2000 / HZ);
-
- tasklet_disable(&hw_priv->rx_tasklet);
- tasklet_disable(&hw_priv->tx_tasklet);
- free_irq(dev->irq, hw_priv->dev);
-
- transmit_cleanup(hw_priv, 0);
- hw_reset_pkts(&hw->rx_desc_info);
- hw_reset_pkts(&hw->tx_desc_info);
-
- /* Clean out static MAC table when the switch is shutdown. */
- if (hw->features & STP_SUPPORT)
- sw_clr_sta_mac_table(hw);
- }
-
- return 0;
-}
-
-static void hw_cfg_huge_frame(struct dev_info *hw_priv, struct ksz_hw *hw)
-{
- if (hw->ksz_switch) {
- u32 data;
-
- data = readw(hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
- if (hw->features & RX_HUGE_FRAME)
- data |= SWITCH_HUGE_PACKET;
- else
- data &= ~SWITCH_HUGE_PACKET;
- writew(data, hw->io + KS8842_SWITCH_CTRL_2_OFFSET);
- }
- if (hw->features & RX_HUGE_FRAME) {
- hw->rx_cfg |= DMA_RX_ERROR;
- hw_priv->dev_rcv = dev_rcv_special;
- } else {
- hw->rx_cfg &= ~DMA_RX_ERROR;
- if (hw->dev_count > 1)
- hw_priv->dev_rcv = port_rcv_packets;
- else
- hw_priv->dev_rcv = dev_rcv_packets;
- }
-}
-
-static int prepare_hardware(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- int rc = 0;
-
- /* Remember the network device that requests interrupts. */
- hw_priv->dev = dev;
- rc = request_irq(dev->irq, netdev_intr, IRQF_SHARED, dev->name, dev);
- if (rc)
- return rc;
- tasklet_enable(&hw_priv->rx_tasklet);
- tasklet_enable(&hw_priv->tx_tasklet);
-
- hw->promiscuous = 0;
- hw->all_multi = 0;
- hw->multi_list_size = 0;
-
- hw_reset(hw);
-
- hw_set_desc_base(hw,
- hw->tx_desc_info.ring_phys, hw->rx_desc_info.ring_phys);
- hw_set_addr(hw);
- hw_cfg_huge_frame(hw_priv, hw);
- ksz_init_rx_buffers(hw_priv);
- return 0;
-}
-
-static void set_media_state(struct net_device *dev, int media_state)
-{
- struct dev_priv *priv = netdev_priv(dev);
-
- if (media_state == priv->media_state)
- netif_carrier_on(dev);
- else
- netif_carrier_off(dev);
- netif_info(priv, link, dev, "link %s\n",
- media_state == priv->media_state ? "on" : "off");
-}
-
-/**
- * netdev_open - open network device
- * @dev: Network device.
- *
- * This function process the open operation of network device. This is caused
- * by the user command "ifconfig ethX up."
- *
- * Return 0 if successful; otherwise an error code indicating failure.
- */
-static int netdev_open(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_port *port = &priv->port;
- int i;
- int p;
- int rc = 0;
-
- priv->multicast = 0;
- priv->promiscuous = 0;
-
- /* Reset device statistics. */
- memset(&dev->stats, 0, sizeof(struct net_device_stats));
- memset((void *) port->counter, 0,
- (sizeof(u64) * OID_COUNTER_LAST));
-
- if (!(hw_priv->opened)) {
- rc = prepare_hardware(dev);
- if (rc)
- return rc;
- for (i = 0; i < hw->mib_port_cnt; i++) {
- if (next_jiffies < jiffies)
- next_jiffies = jiffies + HZ * 2;
- else
- next_jiffies += HZ * 1;
- hw_priv->counter[i].time = next_jiffies;
- hw->port_mib[i].state = media_disconnected;
- port_init_cnt(hw, i);
- }
- if (hw->ksz_switch)
- hw->port_mib[HOST_PORT].state = media_connected;
- else {
- hw_add_wol_bcast(hw);
- hw_cfg_wol_pme(hw, 0);
- hw_clr_wol_pme_status(&hw_priv->hw);
- }
- }
- port_set_power_saving(port, false);
-
- for (i = 0, p = port->first_port; i < port->port_cnt; i++, p++) {
- /*
- * Initialize to invalid value so that link detection
- * is done.
- */
- hw->port_info[p].partner = 0xFF;
- hw->port_info[p].state = media_disconnected;
- }
-
- /* Need to open the port in multiple device interfaces mode. */
- if (hw->dev_count > 1) {
- port_set_stp_state(hw, port->first_port, STP_STATE_SIMPLE);
- if (port->first_port > 0)
- hw_add_addr(hw, dev->dev_addr);
- }
-
- port_get_link_speed(port);
- if (port->force_link)
- port_force_link_speed(port);
- else
- port_set_link_speed(port);
-
- if (!(hw_priv->opened)) {
- hw_setup_intr(hw);
- hw_enable(hw);
- hw_ena_intr(hw);
-
- if (hw->mib_port_cnt)
- ksz_start_timer(&hw_priv->mib_timer_info,
- hw_priv->mib_timer_info.period);
- }
-
- hw_priv->opened++;
-
- ksz_start_timer(&priv->monitor_timer_info,
- priv->monitor_timer_info.period);
-
- priv->media_state = port->linked->state;
-
- set_media_state(dev, media_connected);
- netif_start_queue(dev);
-
- return 0;
-}
-
-/* RX errors = rx_errors */
-/* RX dropped = rx_dropped */
-/* RX overruns = rx_fifo_errors */
-/* RX frame = rx_crc_errors + rx_frame_errors + rx_length_errors */
-/* TX errors = tx_errors */
-/* TX dropped = tx_dropped */
-/* TX overruns = tx_fifo_errors */
-/* TX carrier = tx_aborted_errors + tx_carrier_errors + tx_window_errors */
-/* collisions = collisions */
-
-/**
- * netdev_query_statistics - query network device statistics
- * @dev: Network device.
- *
- * This function returns the statistics of the network device. The device
- * needs not be opened.
- *
- * Return network device statistics.
- */
-static struct net_device_stats *netdev_query_statistics(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct ksz_port *port = &priv->port;
- struct ksz_hw *hw = &priv->adapter->hw;
- struct ksz_port_mib *mib;
- int i;
- int p;
-
- dev->stats.rx_errors = port->counter[OID_COUNTER_RCV_ERROR];
- dev->stats.tx_errors = port->counter[OID_COUNTER_XMIT_ERROR];
-
- /* Reset to zero to add count later. */
- dev->stats.multicast = 0;
- dev->stats.collisions = 0;
- dev->stats.rx_length_errors = 0;
- dev->stats.rx_crc_errors = 0;
- dev->stats.rx_frame_errors = 0;
- dev->stats.tx_window_errors = 0;
-
- for (i = 0, p = port->first_port; i < port->mib_port_cnt; i++, p++) {
- mib = &hw->port_mib[p];
-
- dev->stats.multicast += (unsigned long)
- mib->counter[MIB_COUNTER_RX_MULTICAST];
-
- dev->stats.collisions += (unsigned long)
- mib->counter[MIB_COUNTER_TX_TOTAL_COLLISION];
-
- dev->stats.rx_length_errors += (unsigned long)(
- mib->counter[MIB_COUNTER_RX_UNDERSIZE] +
- mib->counter[MIB_COUNTER_RX_FRAGMENT] +
- mib->counter[MIB_COUNTER_RX_OVERSIZE] +
- mib->counter[MIB_COUNTER_RX_JABBER]);
- dev->stats.rx_crc_errors += (unsigned long)
- mib->counter[MIB_COUNTER_RX_CRC_ERR];
- dev->stats.rx_frame_errors += (unsigned long)(
- mib->counter[MIB_COUNTER_RX_ALIGNMENT_ERR] +
- mib->counter[MIB_COUNTER_RX_SYMBOL_ERR]);
-
- dev->stats.tx_window_errors += (unsigned long)
- mib->counter[MIB_COUNTER_TX_LATE_COLLISION];
- }
-
- return &dev->stats;
-}
-
-/**
- * netdev_set_mac_address - set network device MAC address
- * @dev: Network device.
- * @addr: Buffer of MAC address.
- *
- * This function is used to set the MAC address of the network device.
- *
- * Return 0 to indicate success.
- */
-static int netdev_set_mac_address(struct net_device *dev, void *addr)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct sockaddr *mac = addr;
- uint interrupt;
-
- if (priv->port.first_port > 0)
- hw_del_addr(hw, dev->dev_addr);
- else {
- hw->mac_override = 1;
- memcpy(hw->override_addr, mac->sa_data, MAC_ADDR_LEN);
- }
-
- memcpy(dev->dev_addr, mac->sa_data, MAX_ADDR_LEN);
-
- interrupt = hw_block_intr(hw);
-
- if (priv->port.first_port > 0)
- hw_add_addr(hw, dev->dev_addr);
- else
- hw_set_addr(hw);
- hw_restore_intr(hw, interrupt);
-
- return 0;
-}
-
-static void dev_set_promiscuous(struct net_device *dev, struct dev_priv *priv,
- struct ksz_hw *hw, int promiscuous)
-{
- if (promiscuous != priv->promiscuous) {
- u8 prev_state = hw->promiscuous;
-
- if (promiscuous)
- ++hw->promiscuous;
- else
- --hw->promiscuous;
- priv->promiscuous = promiscuous;
-
- /* Turn on/off promiscuous mode. */
- if (hw->promiscuous <= 1 && prev_state <= 1)
- hw_set_promiscuous(hw, hw->promiscuous);
-
- /*
- * Port is not in promiscuous mode, meaning it is released
- * from the bridge.
- */
- if ((hw->features & STP_SUPPORT) && !promiscuous &&
- (dev->priv_flags & IFF_BRIDGE_PORT)) {
- struct ksz_switch *sw = hw->ksz_switch;
- int port = priv->port.first_port;
-
- port_set_stp_state(hw, port, STP_STATE_DISABLED);
- port = 1 << port;
- if (sw->member & port) {
- sw->member &= ~port;
- bridge_change(hw);
- }
- }
- }
-}
-
-static void dev_set_multicast(struct dev_priv *priv, struct ksz_hw *hw,
- int multicast)
-{
- if (multicast != priv->multicast) {
- u8 all_multi = hw->all_multi;
-
- if (multicast)
- ++hw->all_multi;
- else
- --hw->all_multi;
- priv->multicast = multicast;
-
- /* Turn on/off all multicast mode. */
- if (hw->all_multi <= 1 && all_multi <= 1)
- hw_set_multicast(hw, hw->all_multi);
- }
-}
-
-/**
- * netdev_set_rx_mode
- * @dev: Network device.
- *
- * This routine is used to set multicast addresses or put the network device
- * into promiscuous mode.
- */
-static void netdev_set_rx_mode(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct netdev_hw_addr *ha;
- int multicast = (dev->flags & IFF_ALLMULTI);
-
- dev_set_promiscuous(dev, priv, hw, (dev->flags & IFF_PROMISC));
-
- if (hw_priv->hw.dev_count > 1)
- multicast |= (dev->flags & IFF_MULTICAST);
- dev_set_multicast(priv, hw, multicast);
-
- /* Cannot use different hashes in multiple device interfaces mode. */
- if (hw_priv->hw.dev_count > 1)
- return;
-
- if ((dev->flags & IFF_MULTICAST) && !netdev_mc_empty(dev)) {
- int i = 0;
-
- /* List too big to support so turn on all multicast mode. */
- if (netdev_mc_count(dev) > MAX_MULTICAST_LIST) {
- if (MAX_MULTICAST_LIST != hw->multi_list_size) {
- hw->multi_list_size = MAX_MULTICAST_LIST;
- ++hw->all_multi;
- hw_set_multicast(hw, hw->all_multi);
- }
- return;
- }
-
- netdev_for_each_mc_addr(ha, dev) {
- if (i >= MAX_MULTICAST_LIST)
- break;
- memcpy(hw->multi_list[i++], ha->addr, MAC_ADDR_LEN);
- }
- hw->multi_list_size = (u8) i;
- hw_set_grp_addr(hw);
- } else {
- if (MAX_MULTICAST_LIST == hw->multi_list_size) {
- --hw->all_multi;
- hw_set_multicast(hw, hw->all_multi);
- }
- hw->multi_list_size = 0;
- hw_clr_multicast(hw);
- }
-}
-
-static int netdev_change_mtu(struct net_device *dev, int new_mtu)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- int hw_mtu;
-
- if (netif_running(dev))
- return -EBUSY;
-
- /* Cannot use different MTU in multiple device interfaces mode. */
- if (hw->dev_count > 1)
- if (dev != hw_priv->dev)
- return 0;
- if (new_mtu < 60)
- return -EINVAL;
-
- if (dev->mtu != new_mtu) {
- hw_mtu = new_mtu + ETHERNET_HEADER_SIZE + 4;
- if (hw_mtu > MAX_RX_BUF_SIZE)
- return -EINVAL;
- if (hw_mtu > REGULAR_RX_BUF_SIZE) {
- hw->features |= RX_HUGE_FRAME;
- hw_mtu = MAX_RX_BUF_SIZE;
- } else {
- hw->features &= ~RX_HUGE_FRAME;
- hw_mtu = REGULAR_RX_BUF_SIZE;
- }
- hw_mtu = (hw_mtu + 3) & ~3;
- hw_priv->mtu = hw_mtu;
- dev->mtu = new_mtu;
- }
- return 0;
-}
-
-/**
- * netdev_ioctl - I/O control processing
- * @dev: Network device.
- * @ifr: Interface request structure.
- * @cmd: I/O control code.
- *
- * This function is used to process I/O control calls.
- *
- * Return 0 to indicate success.
- */
-static int netdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_port *port = &priv->port;
- int rc;
- int result = 0;
- struct mii_ioctl_data *data = if_mii(ifr);
-
- if (down_interruptible(&priv->proc_sem))
- return -ERESTARTSYS;
-
- /* assume success */
- rc = 0;
- switch (cmd) {
- /* Get address of MII PHY in use. */
- case SIOCGMIIPHY:
- data->phy_id = priv->id;
-
- /* Fallthrough... */
-
- /* Read MII PHY register. */
- case SIOCGMIIREG:
- if (data->phy_id != priv->id || data->reg_num >= 6)
- result = -EIO;
- else
- hw_r_phy(hw, port->linked->port_id, data->reg_num,
- &data->val_out);
- break;
-
- /* Write MII PHY register. */
- case SIOCSMIIREG:
- if (!capable(CAP_NET_ADMIN))
- result = -EPERM;
- else if (data->phy_id != priv->id || data->reg_num >= 6)
- result = -EIO;
- else
- hw_w_phy(hw, port->linked->port_id, data->reg_num,
- data->val_in);
- break;
-
- default:
- result = -EOPNOTSUPP;
- }
-
- up(&priv->proc_sem);
-
- return result;
-}
-
-/*
- * MII support
- */
-
-/**
- * mdio_read - read PHY register
- * @dev: Network device.
- * @phy_id: The PHY id.
- * @reg_num: The register number.
- *
- * This function returns the PHY register value.
- *
- * Return the register value.
- */
-static int mdio_read(struct net_device *dev, int phy_id, int reg_num)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct ksz_port *port = &priv->port;
- struct ksz_hw *hw = port->hw;
- u16 val_out;
-
- hw_r_phy(hw, port->linked->port_id, reg_num << 1, &val_out);
- return val_out;
-}
-
-/**
- * mdio_write - set PHY register
- * @dev: Network device.
- * @phy_id: The PHY id.
- * @reg_num: The register number.
- * @val: The register value.
- *
- * This procedure sets the PHY register value.
- */
-static void mdio_write(struct net_device *dev, int phy_id, int reg_num, int val)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct ksz_port *port = &priv->port;
- struct ksz_hw *hw = port->hw;
- int i;
- int pi;
-
- for (i = 0, pi = port->first_port; i < port->port_cnt; i++, pi++)
- hw_w_phy(hw, pi, reg_num << 1, val);
-}
-
-/*
- * ethtool support
- */
-
-#define EEPROM_SIZE 0x40
-
-static u16 eeprom_data[EEPROM_SIZE] = { 0 };
-
-#define ADVERTISED_ALL \
- (ADVERTISED_10baseT_Half | \
- ADVERTISED_10baseT_Full | \
- ADVERTISED_100baseT_Half | \
- ADVERTISED_100baseT_Full)
-
-/* These functions use the MII functions in mii.c. */
-
-/**
- * netdev_get_settings - get network device settings
- * @dev: Network device.
- * @cmd: Ethtool command.
- *
- * This function queries the PHY and returns its state in the ethtool command.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
-
- mutex_lock(&hw_priv->lock);
- mii_ethtool_gset(&priv->mii_if, cmd);
- cmd->advertising |= SUPPORTED_TP;
- mutex_unlock(&hw_priv->lock);
-
- /* Save advertised settings for workaround in next function. */
- priv->advertising = cmd->advertising;
- return 0;
-}
-
-/**
- * netdev_set_settings - set network device settings
- * @dev: Network device.
- * @cmd: Ethtool command.
- *
- * This function sets the PHY according to the ethtool command.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_port *port = &priv->port;
- u32 speed = ethtool_cmd_speed(cmd);
- int rc;
-
- /*
- * ethtool utility does not change advertised setting if auto
- * negotiation is not specified explicitly.
- */
- if (cmd->autoneg && priv->advertising == cmd->advertising) {
- cmd->advertising |= ADVERTISED_ALL;
- if (10 == speed)
- cmd->advertising &=
- ~(ADVERTISED_100baseT_Full |
- ADVERTISED_100baseT_Half);
- else if (100 == speed)
- cmd->advertising &=
- ~(ADVERTISED_10baseT_Full |
- ADVERTISED_10baseT_Half);
- if (0 == cmd->duplex)
- cmd->advertising &=
- ~(ADVERTISED_100baseT_Full |
- ADVERTISED_10baseT_Full);
- else if (1 == cmd->duplex)
- cmd->advertising &=
- ~(ADVERTISED_100baseT_Half |
- ADVERTISED_10baseT_Half);
- }
- mutex_lock(&hw_priv->lock);
- if (cmd->autoneg &&
- (cmd->advertising & ADVERTISED_ALL) ==
- ADVERTISED_ALL) {
- port->duplex = 0;
- port->speed = 0;
- port->force_link = 0;
- } else {
- port->duplex = cmd->duplex + 1;
- if (1000 != speed)
- port->speed = speed;
- if (cmd->autoneg)
- port->force_link = 0;
- else
- port->force_link = 1;
- }
- rc = mii_ethtool_sset(&priv->mii_if, cmd);
- mutex_unlock(&hw_priv->lock);
- return rc;
-}
-
-/**
- * netdev_nway_reset - restart auto-negotiation
- * @dev: Network device.
- *
- * This function restarts the PHY for auto-negotiation.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_nway_reset(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- int rc;
-
- mutex_lock(&hw_priv->lock);
- rc = mii_nway_restart(&priv->mii_if);
- mutex_unlock(&hw_priv->lock);
- return rc;
-}
-
-/**
- * netdev_get_link - get network device link status
- * @dev: Network device.
- *
- * This function gets the link status from the PHY.
- *
- * Return true if PHY is linked and false otherwise.
- */
-static u32 netdev_get_link(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
- int rc;
-
- rc = mii_link_ok(&priv->mii_if);
- return rc;
-}
-
-/**
- * netdev_get_drvinfo - get network driver information
- * @dev: Network device.
- * @info: Ethtool driver info data structure.
- *
- * This procedure returns the driver information.
- */
-static void netdev_get_drvinfo(struct net_device *dev,
- struct ethtool_drvinfo *info)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
-
- strcpy(info->driver, DRV_NAME);
- strcpy(info->version, DRV_VERSION);
- strcpy(info->bus_info, pci_name(hw_priv->pdev));
-}
-
-/**
- * netdev_get_regs_len - get length of register dump
- * @dev: Network device.
- *
- * This function returns the length of the register dump.
- *
- * Return length of the register dump.
- */
-static struct hw_regs {
- int start;
- int end;
-} hw_regs_range[] = {
- { KS_DMA_TX_CTRL, KS884X_INTERRUPTS_STATUS },
- { KS_ADD_ADDR_0_LO, KS_ADD_ADDR_F_HI },
- { KS884X_ADDR_0_OFFSET, KS8841_WOL_FRAME_BYTE2_OFFSET },
- { KS884X_SIDER_P, KS8842_SGCR7_P },
- { KS8842_MACAR1_P, KS8842_TOSR8_P },
- { KS884X_P1MBCR_P, KS8842_P3ERCR_P },
- { 0, 0 }
-};
-
-static int netdev_get_regs_len(struct net_device *dev)
-{
- struct hw_regs *range = hw_regs_range;
- int regs_len = 0x10 * sizeof(u32);
-
- while (range->end > range->start) {
- regs_len += (range->end - range->start + 3) / 4 * 4;
- range++;
- }
- return regs_len;
-}
-
-/**
- * netdev_get_regs - get register dump
- * @dev: Network device.
- * @regs: Ethtool registers data structure.
- * @ptr: Buffer to store the register values.
- *
- * This procedure dumps the register values in the provided buffer.
- */
-static void netdev_get_regs(struct net_device *dev, struct ethtool_regs *regs,
- void *ptr)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- int *buf = (int *) ptr;
- struct hw_regs *range = hw_regs_range;
- int len;
-
- mutex_lock(&hw_priv->lock);
- regs->version = 0;
- for (len = 0; len < 0x40; len += 4) {
- pci_read_config_dword(hw_priv->pdev, len, buf);
- buf++;
- }
- while (range->end > range->start) {
- for (len = range->start; len < range->end; len += 4) {
- *buf = readl(hw->io + len);
- buf++;
- }
- range++;
- }
- mutex_unlock(&hw_priv->lock);
-}
-
-#define WOL_SUPPORT \
- (WAKE_PHY | WAKE_MAGIC | \
- WAKE_UCAST | WAKE_MCAST | \
- WAKE_BCAST | WAKE_ARP)
-
-/**
- * netdev_get_wol - get Wake-on-LAN support
- * @dev: Network device.
- * @wol: Ethtool Wake-on-LAN data structure.
- *
- * This procedure returns Wake-on-LAN support.
- */
-static void netdev_get_wol(struct net_device *dev,
- struct ethtool_wolinfo *wol)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
-
- wol->supported = hw_priv->wol_support;
- wol->wolopts = hw_priv->wol_enable;
- memset(&wol->sopass, 0, sizeof(wol->sopass));
-}
-
-/**
- * netdev_set_wol - set Wake-on-LAN support
- * @dev: Network device.
- * @wol: Ethtool Wake-on-LAN data structure.
- *
- * This function sets Wake-on-LAN support.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_set_wol(struct net_device *dev,
- struct ethtool_wolinfo *wol)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
-
- /* Need to find a way to retrieve the device IP address. */
- static const u8 net_addr[] = { 192, 168, 1, 1 };
-
- if (wol->wolopts & ~hw_priv->wol_support)
- return -EINVAL;
-
- hw_priv->wol_enable = wol->wolopts;
-
- /* Link wakeup cannot really be disabled. */
- if (wol->wolopts)
- hw_priv->wol_enable |= WAKE_PHY;
- hw_enable_wol(&hw_priv->hw, hw_priv->wol_enable, net_addr);
- return 0;
-}
-
-/**
- * netdev_get_msglevel - get debug message level
- * @dev: Network device.
- *
- * This function returns current debug message level.
- *
- * Return current debug message flags.
- */
-static u32 netdev_get_msglevel(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
-
- return priv->msg_enable;
-}
-
-/**
- * netdev_set_msglevel - set debug message level
- * @dev: Network device.
- * @value: Debug message flags.
- *
- * This procedure sets debug message level.
- */
-static void netdev_set_msglevel(struct net_device *dev, u32 value)
-{
- struct dev_priv *priv = netdev_priv(dev);
-
- priv->msg_enable = value;
-}
-
-/**
- * netdev_get_eeprom_len - get EEPROM length
- * @dev: Network device.
- *
- * This function returns the length of the EEPROM.
- *
- * Return length of the EEPROM.
- */
-static int netdev_get_eeprom_len(struct net_device *dev)
-{
- return EEPROM_SIZE * 2;
-}
-
-/**
- * netdev_get_eeprom - get EEPROM data
- * @dev: Network device.
- * @eeprom: Ethtool EEPROM data structure.
- * @data: Buffer to store the EEPROM data.
- *
- * This function dumps the EEPROM data in the provided buffer.
- *
- * Return 0 if successful; otherwise an error code.
- */
-#define EEPROM_MAGIC 0x10A18842
-
-static int netdev_get_eeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 *data)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- u8 *eeprom_byte = (u8 *) eeprom_data;
- int i;
- int len;
-
- len = (eeprom->offset + eeprom->len + 1) / 2;
- for (i = eeprom->offset / 2; i < len; i++)
- eeprom_data[i] = eeprom_read(&hw_priv->hw, i);
- eeprom->magic = EEPROM_MAGIC;
- memcpy(data, &eeprom_byte[eeprom->offset], eeprom->len);
-
- return 0;
-}
-
-/**
- * netdev_set_eeprom - write EEPROM data
- * @dev: Network device.
- * @eeprom: Ethtool EEPROM data structure.
- * @data: Data buffer.
- *
- * This function modifies the EEPROM data one byte at a time.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_set_eeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 *data)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- u16 eeprom_word[EEPROM_SIZE];
- u8 *eeprom_byte = (u8 *) eeprom_word;
- int i;
- int len;
-
- if (eeprom->magic != EEPROM_MAGIC)
- return -EINVAL;
-
- len = (eeprom->offset + eeprom->len + 1) / 2;
- for (i = eeprom->offset / 2; i < len; i++)
- eeprom_data[i] = eeprom_read(&hw_priv->hw, i);
- memcpy(eeprom_word, eeprom_data, EEPROM_SIZE * 2);
- memcpy(&eeprom_byte[eeprom->offset], data, eeprom->len);
- for (i = 0; i < EEPROM_SIZE; i++)
- if (eeprom_word[i] != eeprom_data[i]) {
- eeprom_data[i] = eeprom_word[i];
- eeprom_write(&hw_priv->hw, i, eeprom_data[i]);
- }
-
- return 0;
-}
-
-/**
- * netdev_get_pauseparam - get flow control parameters
- * @dev: Network device.
- * @pause: Ethtool PAUSE settings data structure.
- *
- * This procedure returns the PAUSE control flow settings.
- */
-static void netdev_get_pauseparam(struct net_device *dev,
- struct ethtool_pauseparam *pause)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
-
- pause->autoneg = (hw->overrides & PAUSE_FLOW_CTRL) ? 0 : 1;
- if (!hw->ksz_switch) {
- pause->rx_pause =
- (hw->rx_cfg & DMA_RX_FLOW_ENABLE) ? 1 : 0;
- pause->tx_pause =
- (hw->tx_cfg & DMA_TX_FLOW_ENABLE) ? 1 : 0;
- } else {
- pause->rx_pause =
- (sw_chk(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_RX_FLOW_CTRL)) ? 1 : 0;
- pause->tx_pause =
- (sw_chk(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_TX_FLOW_CTRL)) ? 1 : 0;
- }
-}
-
-/**
- * netdev_set_pauseparam - set flow control parameters
- * @dev: Network device.
- * @pause: Ethtool PAUSE settings data structure.
- *
- * This function sets the PAUSE control flow settings.
- * Not implemented yet.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_set_pauseparam(struct net_device *dev,
- struct ethtool_pauseparam *pause)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_port *port = &priv->port;
-
- mutex_lock(&hw_priv->lock);
- if (pause->autoneg) {
- if (!pause->rx_pause && !pause->tx_pause)
- port->flow_ctrl = PHY_NO_FLOW_CTRL;
- else
- port->flow_ctrl = PHY_FLOW_CTRL;
- hw->overrides &= ~PAUSE_FLOW_CTRL;
- port->force_link = 0;
- if (hw->ksz_switch) {
- sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_RX_FLOW_CTRL, 1);
- sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_TX_FLOW_CTRL, 1);
- }
- port_set_link_speed(port);
- } else {
- hw->overrides |= PAUSE_FLOW_CTRL;
- if (hw->ksz_switch) {
- sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_RX_FLOW_CTRL, pause->rx_pause);
- sw_cfg(hw, KS8842_SWITCH_CTRL_1_OFFSET,
- SWITCH_TX_FLOW_CTRL, pause->tx_pause);
- } else
- set_flow_ctrl(hw, pause->rx_pause, pause->tx_pause);
- }
- mutex_unlock(&hw_priv->lock);
-
- return 0;
-}
-
-/**
- * netdev_get_ringparam - get tx/rx ring parameters
- * @dev: Network device.
- * @pause: Ethtool RING settings data structure.
- *
- * This procedure returns the TX/RX ring settings.
- */
-static void netdev_get_ringparam(struct net_device *dev,
- struct ethtool_ringparam *ring)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
-
- ring->tx_max_pending = (1 << 9);
- ring->tx_pending = hw->tx_desc_info.alloc;
- ring->rx_max_pending = (1 << 9);
- ring->rx_pending = hw->rx_desc_info.alloc;
-}
-
-#define STATS_LEN (TOTAL_PORT_COUNTER_NUM)
-
-static struct {
- char string[ETH_GSTRING_LEN];
-} ethtool_stats_keys[STATS_LEN] = {
- { "rx_lo_priority_octets" },
- { "rx_hi_priority_octets" },
- { "rx_undersize_packets" },
- { "rx_fragments" },
- { "rx_oversize_packets" },
- { "rx_jabbers" },
- { "rx_symbol_errors" },
- { "rx_crc_errors" },
- { "rx_align_errors" },
- { "rx_mac_ctrl_packets" },
- { "rx_pause_packets" },
- { "rx_bcast_packets" },
- { "rx_mcast_packets" },
- { "rx_ucast_packets" },
- { "rx_64_or_less_octet_packets" },
- { "rx_65_to_127_octet_packets" },
- { "rx_128_to_255_octet_packets" },
- { "rx_256_to_511_octet_packets" },
- { "rx_512_to_1023_octet_packets" },
- { "rx_1024_to_1522_octet_packets" },
-
- { "tx_lo_priority_octets" },
- { "tx_hi_priority_octets" },
- { "tx_late_collisions" },
- { "tx_pause_packets" },
- { "tx_bcast_packets" },
- { "tx_mcast_packets" },
- { "tx_ucast_packets" },
- { "tx_deferred" },
- { "tx_total_collisions" },
- { "tx_excessive_collisions" },
- { "tx_single_collisions" },
- { "tx_mult_collisions" },
-
- { "rx_discards" },
- { "tx_discards" },
-};
-
-/**
- * netdev_get_strings - get statistics identity strings
- * @dev: Network device.
- * @stringset: String set identifier.
- * @buf: Buffer to store the strings.
- *
- * This procedure returns the strings used to identify the statistics.
- */
-static void netdev_get_strings(struct net_device *dev, u32 stringset, u8 *buf)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
-
- if (ETH_SS_STATS == stringset)
- memcpy(buf, ðtool_stats_keys,
- ETH_GSTRING_LEN * hw->mib_cnt);
-}
-
-/**
- * netdev_get_sset_count - get statistics size
- * @dev: Network device.
- * @sset: The statistics set number.
- *
- * This function returns the size of the statistics to be reported.
- *
- * Return size of the statistics to be reported.
- */
-static int netdev_get_sset_count(struct net_device *dev, int sset)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
-
- switch (sset) {
- case ETH_SS_STATS:
- return hw->mib_cnt;
- default:
- return -EOPNOTSUPP;
- }
-}
-
-/**
- * netdev_get_ethtool_stats - get network device statistics
- * @dev: Network device.
- * @stats: Ethtool statistics data structure.
- * @data: Buffer to store the statistics.
- *
- * This procedure returns the statistics.
- */
-static void netdev_get_ethtool_stats(struct net_device *dev,
- struct ethtool_stats *stats, u64 *data)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_port *port = &priv->port;
- int n_stats = stats->n_stats;
- int i;
- int n;
- int p;
- int rc;
- u64 counter[TOTAL_PORT_COUNTER_NUM];
-
- mutex_lock(&hw_priv->lock);
- n = SWITCH_PORT_NUM;
- for (i = 0, p = port->first_port; i < port->mib_port_cnt; i++, p++) {
- if (media_connected == hw->port_mib[p].state) {
- hw_priv->counter[p].read = 1;
-
- /* Remember first port that requests read. */
- if (n == SWITCH_PORT_NUM)
- n = p;
- }
- }
- mutex_unlock(&hw_priv->lock);
-
- if (n < SWITCH_PORT_NUM)
- schedule_work(&hw_priv->mib_read);
-
- if (1 == port->mib_port_cnt && n < SWITCH_PORT_NUM) {
- p = n;
- rc = wait_event_interruptible_timeout(
- hw_priv->counter[p].counter,
- 2 == hw_priv->counter[p].read,
- HZ * 1);
- } else
- for (i = 0, p = n; i < port->mib_port_cnt - n; i++, p++) {
- if (0 == i) {
- rc = wait_event_interruptible_timeout(
- hw_priv->counter[p].counter,
- 2 == hw_priv->counter[p].read,
- HZ * 2);
- } else if (hw->port_mib[p].cnt_ptr) {
- rc = wait_event_interruptible_timeout(
- hw_priv->counter[p].counter,
- 2 == hw_priv->counter[p].read,
- HZ * 1);
- }
- }
-
- get_mib_counters(hw, port->first_port, port->mib_port_cnt, counter);
- n = hw->mib_cnt;
- if (n > n_stats)
- n = n_stats;
- n_stats -= n;
- for (i = 0; i < n; i++)
- *data++ = counter[i];
-}
-
-/**
- * netdev_set_features - set receive checksum support
- * @dev: Network device.
- * @features: New device features (offloads).
- *
- * This function sets receive checksum support setting.
- *
- * Return 0 if successful; otherwise an error code.
- */
-static int netdev_set_features(struct net_device *dev, u32 features)
-{
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
-
- mutex_lock(&hw_priv->lock);
-
- /* see note in hw_setup() */
- if (features & NETIF_F_RXCSUM)
- hw->rx_cfg |= DMA_RX_CSUM_TCP | DMA_RX_CSUM_IP;
- else
- hw->rx_cfg &= ~(DMA_RX_CSUM_TCP | DMA_RX_CSUM_IP);
-
- if (hw->enabled)
- writel(hw->rx_cfg, hw->io + KS_DMA_RX_CTRL);
-
- mutex_unlock(&hw_priv->lock);
-
- return 0;
-}
-
-static struct ethtool_ops netdev_ethtool_ops = {
- .get_settings = netdev_get_settings,
- .set_settings = netdev_set_settings,
- .nway_reset = netdev_nway_reset,
- .get_link = netdev_get_link,
- .get_drvinfo = netdev_get_drvinfo,
- .get_regs_len = netdev_get_regs_len,
- .get_regs = netdev_get_regs,
- .get_wol = netdev_get_wol,
- .set_wol = netdev_set_wol,
- .get_msglevel = netdev_get_msglevel,
- .set_msglevel = netdev_set_msglevel,
- .get_eeprom_len = netdev_get_eeprom_len,
- .get_eeprom = netdev_get_eeprom,
- .set_eeprom = netdev_set_eeprom,
- .get_pauseparam = netdev_get_pauseparam,
- .set_pauseparam = netdev_set_pauseparam,
- .get_ringparam = netdev_get_ringparam,
- .get_strings = netdev_get_strings,
- .get_sset_count = netdev_get_sset_count,
- .get_ethtool_stats = netdev_get_ethtool_stats,
-};
-
-/*
- * Hardware monitoring
- */
-
-static void update_link(struct net_device *dev, struct dev_priv *priv,
- struct ksz_port *port)
-{
- if (priv->media_state != port->linked->state) {
- priv->media_state = port->linked->state;
- if (netif_running(dev))
- set_media_state(dev, media_connected);
- }
-}
-
-static void mib_read_work(struct work_struct *work)
-{
- struct dev_info *hw_priv =
- container_of(work, struct dev_info, mib_read);
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_port_mib *mib;
- int i;
-
- next_jiffies = jiffies;
- for (i = 0; i < hw->mib_port_cnt; i++) {
- mib = &hw->port_mib[i];
-
- /* Reading MIB counters or requested to read. */
- if (mib->cnt_ptr || 1 == hw_priv->counter[i].read) {
-
- /* Need to process receive interrupt. */
- if (port_r_cnt(hw, i))
- break;
- hw_priv->counter[i].read = 0;
-
- /* Finish reading counters. */
- if (0 == mib->cnt_ptr) {
- hw_priv->counter[i].read = 2;
- wake_up_interruptible(
- &hw_priv->counter[i].counter);
- }
- } else if (jiffies >= hw_priv->counter[i].time) {
- /* Only read MIB counters when the port is connected. */
- if (media_connected == mib->state)
- hw_priv->counter[i].read = 1;
- next_jiffies += HZ * 1 * hw->mib_port_cnt;
- hw_priv->counter[i].time = next_jiffies;
-
- /* Port is just disconnected. */
- } else if (mib->link_down) {
- mib->link_down = 0;
-
- /* Read counters one last time after link is lost. */
- hw_priv->counter[i].read = 1;
- }
- }
-}
-
-static void mib_monitor(unsigned long ptr)
-{
- struct dev_info *hw_priv = (struct dev_info *) ptr;
-
- mib_read_work(&hw_priv->mib_read);
-
- /* This is used to verify Wake-on-LAN is working. */
- if (hw_priv->pme_wait) {
- if (hw_priv->pme_wait <= jiffies) {
- hw_clr_wol_pme_status(&hw_priv->hw);
- hw_priv->pme_wait = 0;
- }
- } else if (hw_chk_wol_pme_status(&hw_priv->hw)) {
-
- /* PME is asserted. Wait 2 seconds to clear it. */
- hw_priv->pme_wait = jiffies + HZ * 2;
- }
-
- ksz_update_timer(&hw_priv->mib_timer_info);
-}
-
-/**
- * dev_monitor - periodic monitoring
- * @ptr: Network device pointer.
- *
- * This routine is run in a kernel timer to monitor the network device.
- */
-static void dev_monitor(unsigned long ptr)
-{
- struct net_device *dev = (struct net_device *) ptr;
- struct dev_priv *priv = netdev_priv(dev);
- struct dev_info *hw_priv = priv->adapter;
- struct ksz_hw *hw = &hw_priv->hw;
- struct ksz_port *port = &priv->port;
-
- if (!(hw->features & LINK_INT_WORKING))
- port_get_link_speed(port);
- update_link(dev, priv, port);
-
- ksz_update_timer(&priv->monitor_timer_info);
-}
-
-/*
- * Linux network device interface functions
- */
-
-/* Driver exported variables */
-
-static int msg_enable;
-
-static char *macaddr = ":";
-static char *mac1addr = ":";
-
-/*
- * This enables multiple network device mode for KSZ8842, which contains a
- * switch with two physical ports. Some users like to take control of the
- * ports for running Spanning Tree Protocol. The driver will create an
- * additional eth? device for the other port.
- *
- * Some limitations are the network devices cannot have different MTU and
- * multicast hash tables.
- */
-static int multi_dev;
-
-/*
- * As most users select multiple network device mode to use Spanning Tree
- * Protocol, this enables a feature in which most unicast and multicast packets
- * are forwarded inside the switch and not passed to the host. Only packets
- * that need the host's attention are passed to it. This prevents the host
- * wasting CPU time to examine each and every incoming packets and do the
- * forwarding itself.
- *
- * As the hack requires the private bridge header, the driver cannot compile
- * with just the kernel headers.
- *
- * Enabling STP support also turns on multiple network device mode.
- */
-static int stp;
-
-/*
- * This enables fast aging in the KSZ8842 switch. Not sure what situation
- * needs that. However, fast aging is used to flush the dynamic MAC table when
- * STP suport is enabled.
- */
-static int fast_aging;
-
-/**
- * netdev_init - initialize network device.
- * @dev: Network device.
- *
- * This function initializes the network device.
- *
- * Return 0 if successful; otherwise an error code indicating failure.
- */
-static int __init netdev_init(struct net_device *dev)
-{
- struct dev_priv *priv = netdev_priv(dev);
-
- /* 500 ms timeout */
- ksz_init_timer(&priv->monitor_timer_info, 500 * HZ / 1000,
- dev_monitor, dev);
-
- /* 500 ms timeout */
- dev->watchdog_timeo = HZ / 2;
-
- dev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_RXCSUM;
-
- /*
- * Hardware does not really support IPv6 checksum generation, but
- * driver actually runs faster with this on.
- */
- dev->hw_features |= NETIF_F_IPV6_CSUM;
-
- dev->features |= dev->hw_features;
-
- sema_init(&priv->proc_sem, 1);
-
- priv->mii_if.phy_id_mask = 0x1;
- priv->mii_if.reg_num_mask = 0x7;
- priv->mii_if.dev = dev;
- priv->mii_if.mdio_read = mdio_read;
- priv->mii_if.mdio_write = mdio_write;
- priv->mii_if.phy_id = priv->port.first_port + 1;
-
- priv->msg_enable = netif_msg_init(msg_enable,
- (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK));
-
- return 0;
-}
-
-static const struct net_device_ops netdev_ops = {
- .ndo_init = netdev_init,
- .ndo_open = netdev_open,
- .ndo_stop = netdev_close,
- .ndo_get_stats = netdev_query_statistics,
- .ndo_start_xmit = netdev_tx,
- .ndo_tx_timeout = netdev_tx_timeout,
- .ndo_change_mtu = netdev_change_mtu,
- .ndo_set_features = netdev_set_features,
- .ndo_set_mac_address = netdev_set_mac_address,
- .ndo_validate_addr = eth_validate_addr,
- .ndo_do_ioctl = netdev_ioctl,
- .ndo_set_rx_mode = netdev_set_rx_mode,
-#ifdef CONFIG_NET_POLL_CONTROLLER
- .ndo_poll_controller = netdev_netpoll,
-#endif
-};
-
-static void netdev_free(struct net_device *dev)
-{
- if (dev->watchdog_timeo)
- unregister_netdev(dev);
-
- free_netdev(dev);
-}
-
-struct platform_info {
- struct dev_info dev_info;
- struct net_device *netdev[SWITCH_PORT_NUM];
-};
-
-static int net_device_present;
-
-static void get_mac_addr(struct dev_info *hw_priv, u8 *macaddr, int port)
-{
- int i;
- int j;
- int got_num;
- int num;
-
- i = j = num = got_num = 0;
- while (j < MAC_ADDR_LEN) {
- if (macaddr[i]) {
- int digit;
-
- got_num = 1;
- digit = hex_to_bin(macaddr[i]);
- if (digit >= 0)
- num = num * 16 + digit;
- else if (':' == macaddr[i])
- got_num = 2;
- else
- break;
- } else if (got_num)
- got_num = 2;
- else
- break;
- if (2 == got_num) {
- if (MAIN_PORT == port) {
- hw_priv->hw.override_addr[j++] = (u8) num;
- hw_priv->hw.override_addr[5] +=
- hw_priv->hw.id;
- } else {
- hw_priv->hw.ksz_switch->other_addr[j++] =
- (u8) num;
- hw_priv->hw.ksz_switch->other_addr[5] +=
- hw_priv->hw.id;
- }
- num = got_num = 0;
- }
- i++;
- }
- if (MAC_ADDR_LEN == j) {
- if (MAIN_PORT == port)
- hw_priv->hw.mac_override = 1;
- }
-}
-
-#define KS884X_DMA_MASK (~0x0UL)
-
-static void read_other_addr(struct ksz_hw *hw)
-{
- int i;
- u16 data[3];
- struct ksz_switch *sw = hw->ksz_switch;
-
- for (i = 0; i < 3; i++)
- data[i] = eeprom_read(hw, i + EEPROM_DATA_OTHER_MAC_ADDR);
- if ((data[0] || data[1] || data[2]) && data[0] != 0xffff) {
- sw->other_addr[5] = (u8) data[0];
- sw->other_addr[4] = (u8)(data[0] >> 8);
- sw->other_addr[3] = (u8) data[1];
- sw->other_addr[2] = (u8)(data[1] >> 8);
- sw->other_addr[1] = (u8) data[2];
- sw->other_addr[0] = (u8)(data[2] >> 8);
- }
-}
-
-#ifndef PCI_VENDOR_ID_MICREL_KS
-#define PCI_VENDOR_ID_MICREL_KS 0x16c6
-#endif
-
-static int __devinit pcidev_init(struct pci_dev *pdev,
- const struct pci_device_id *id)
-{
- struct net_device *dev;
- struct dev_priv *priv;
- struct dev_info *hw_priv;
- struct ksz_hw *hw;
- struct platform_info *info;
- struct ksz_port *port;
- unsigned long reg_base;
- unsigned long reg_len;
- int cnt;
- int i;
- int mib_port_count;
- int pi;
- int port_count;
- int result;
- char banner[sizeof(version)];
- struct ksz_switch *sw = NULL;
-
- result = pci_enable_device(pdev);
- if (result)
- return result;
-
- result = -ENODEV;
-
- if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32)) ||
- pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)))
- return result;
-
- reg_base = pci_resource_start(pdev, 0);
- reg_len = pci_resource_len(pdev, 0);
- if ((pci_resource_flags(pdev, 0) & IORESOURCE_IO) != 0)
- return result;
-
- if (!request_mem_region(reg_base, reg_len, DRV_NAME))
- return result;
- pci_set_master(pdev);
-
- result = -ENOMEM;
-
- info = kzalloc(sizeof(struct platform_info), GFP_KERNEL);
- if (!info)
- goto pcidev_init_dev_err;
-
- hw_priv = &info->dev_info;
- hw_priv->pdev = pdev;
-
- hw = &hw_priv->hw;
-
- hw->io = ioremap(reg_base, reg_len);
- if (!hw->io)
- goto pcidev_init_io_err;
-
- cnt = hw_init(hw);
- if (!cnt) {
- if (msg_enable & NETIF_MSG_PROBE)
- pr_alert("chip not detected\n");
- result = -ENODEV;
- goto pcidev_init_alloc_err;
- }
-
- snprintf(banner, sizeof(banner), "%s", version);
- banner[13] = cnt + '0'; /* Replace x in "Micrel KSZ884x" */
- dev_info(&hw_priv->pdev->dev, "%s\n", banner);
- dev_dbg(&hw_priv->pdev->dev, "Mem = %p; IRQ = %d\n", hw->io, pdev->irq);
-
- /* Assume device is KSZ8841. */
- hw->dev_count = 1;
- port_count = 1;
- mib_port_count = 1;
- hw->addr_list_size = 0;
- hw->mib_cnt = PORT_COUNTER_NUM;
- hw->mib_port_cnt = 1;
-
- /* KSZ8842 has a switch with multiple ports. */
- if (2 == cnt) {
- if (fast_aging)
- hw->overrides |= FAST_AGING;
-
- hw->mib_cnt = TOTAL_PORT_COUNTER_NUM;
-
- /* Multiple network device interfaces are required. */
- if (multi_dev) {
- hw->dev_count = SWITCH_PORT_NUM;
- hw->addr_list_size = SWITCH_PORT_NUM - 1;
- }
-
- /* Single network device has multiple ports. */
- if (1 == hw->dev_count) {
- port_count = SWITCH_PORT_NUM;
- mib_port_count = SWITCH_PORT_NUM;
- }
- hw->mib_port_cnt = TOTAL_PORT_NUM;
- hw->ksz_switch = kzalloc(sizeof(struct ksz_switch), GFP_KERNEL);
- if (!hw->ksz_switch)
- goto pcidev_init_alloc_err;
-
- sw = hw->ksz_switch;
- }
- for (i = 0; i < hw->mib_port_cnt; i++)
- hw->port_mib[i].mib_start = 0;
-
- hw->parent = hw_priv;
-
- /* Default MTU is 1500. */
- hw_priv->mtu = (REGULAR_RX_BUF_SIZE + 3) & ~3;
-
- if (ksz_alloc_mem(hw_priv))
- goto pcidev_init_mem_err;
-
- hw_priv->hw.id = net_device_present;
-
- spin_lock_init(&hw_priv->hwlock);
- mutex_init(&hw_priv->lock);
-
- /* tasklet is enabled. */
- tasklet_init(&hw_priv->rx_tasklet, rx_proc_task,
- (unsigned long) hw_priv);
- tasklet_init(&hw_priv->tx_tasklet, tx_proc_task,
- (unsigned long) hw_priv);
-
- /* tasklet_enable will decrement the atomic counter. */
- tasklet_disable(&hw_priv->rx_tasklet);
- tasklet_disable(&hw_priv->tx_tasklet);
-
- for (i = 0; i < TOTAL_PORT_NUM; i++)
- init_waitqueue_head(&hw_priv->counter[i].counter);
-
- if (macaddr[0] != ':')
- get_mac_addr(hw_priv, macaddr, MAIN_PORT);
-
- /* Read MAC address and initialize override address if not overrided. */
- hw_read_addr(hw);
-
- /* Multiple device interfaces mode requires a second MAC address. */
- if (hw->dev_count > 1) {
- memcpy(sw->other_addr, hw->override_addr, MAC_ADDR_LEN);
- read_other_addr(hw);
- if (mac1addr[0] != ':')
- get_mac_addr(hw_priv, mac1addr, OTHER_PORT);
- }
-
- hw_setup(hw);
- if (hw->ksz_switch)
- sw_setup(hw);
- else {
- hw_priv->wol_support = WOL_SUPPORT;
- hw_priv->wol_enable = 0;
- }
-
- INIT_WORK(&hw_priv->mib_read, mib_read_work);
-
- /* 500 ms timeout */
- ksz_init_timer(&hw_priv->mib_timer_info, 500 * HZ / 1000,
- mib_monitor, hw_priv);
-
- for (i = 0; i < hw->dev_count; i++) {
- dev = alloc_etherdev(sizeof(struct dev_priv));
- if (!dev)
- goto pcidev_init_reg_err;
- info->netdev[i] = dev;
-
- priv = netdev_priv(dev);
- priv->adapter = hw_priv;
- priv->id = net_device_present++;
-
- port = &priv->port;
- port->port_cnt = port_count;
- port->mib_port_cnt = mib_port_count;
- port->first_port = i;
- port->flow_ctrl = PHY_FLOW_CTRL;
-
- port->hw = hw;
- port->linked = &hw->port_info[port->first_port];
-
- for (cnt = 0, pi = i; cnt < port_count; cnt++, pi++) {
- hw->port_info[pi].port_id = pi;
- hw->port_info[pi].pdev = dev;
- hw->port_info[pi].state = media_disconnected;
- }
-
- dev->mem_start = (unsigned long) hw->io;
- dev->mem_end = dev->mem_start + reg_len - 1;
- dev->irq = pdev->irq;
- if (MAIN_PORT == i)
- memcpy(dev->dev_addr, hw_priv->hw.override_addr,
- MAC_ADDR_LEN);
- else {
- memcpy(dev->dev_addr, sw->other_addr,
- MAC_ADDR_LEN);
- if (!memcmp(sw->other_addr, hw->override_addr,
- MAC_ADDR_LEN))
- dev->dev_addr[5] += port->first_port;
- }
-
- dev->netdev_ops = &netdev_ops;
- SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
- if (register_netdev(dev))
- goto pcidev_init_reg_err;
- port_set_power_saving(port, true);
- }
-
- pci_dev_get(hw_priv->pdev);
- pci_set_drvdata(pdev, info);
- return 0;
-
-pcidev_init_reg_err:
- for (i = 0; i < hw->dev_count; i++) {
- if (info->netdev[i]) {
- netdev_free(info->netdev[i]);
- info->netdev[i] = NULL;
- }
- }
-
-pcidev_init_mem_err:
- ksz_free_mem(hw_priv);
- kfree(hw->ksz_switch);
-
-pcidev_init_alloc_err:
- iounmap(hw->io);
-
-pcidev_init_io_err:
- kfree(info);
-
-pcidev_init_dev_err:
- release_mem_region(reg_base, reg_len);
-
- return result;
-}
-
-static void pcidev_exit(struct pci_dev *pdev)
-{
- int i;
- struct platform_info *info = pci_get_drvdata(pdev);
- struct dev_info *hw_priv = &info->dev_info;
-
- pci_set_drvdata(pdev, NULL);
-
- release_mem_region(pci_resource_start(pdev, 0),
- pci_resource_len(pdev, 0));
- for (i = 0; i < hw_priv->hw.dev_count; i++) {
- if (info->netdev[i])
- netdev_free(info->netdev[i]);
- }
- if (hw_priv->hw.io)
- iounmap(hw_priv->hw.io);
- ksz_free_mem(hw_priv);
- kfree(hw_priv->hw.ksz_switch);
- pci_dev_put(hw_priv->pdev);
- kfree(info);
-}
-
-#ifdef CONFIG_PM
-static int pcidev_resume(struct pci_dev *pdev)
-{
- int i;
- struct platform_info *info = pci_get_drvdata(pdev);
- struct dev_info *hw_priv = &info->dev_info;
- struct ksz_hw *hw = &hw_priv->hw;
-
- pci_set_power_state(pdev, PCI_D0);
- pci_restore_state(pdev);
- pci_enable_wake(pdev, PCI_D0, 0);
-
- if (hw_priv->wol_enable)
- hw_cfg_wol_pme(hw, 0);
- for (i = 0; i < hw->dev_count; i++) {
- if (info->netdev[i]) {
- struct net_device *dev = info->netdev[i];
-
- if (netif_running(dev)) {
- netdev_open(dev);
- netif_device_attach(dev);
- }
- }
- }
- return 0;
-}
-
-static int pcidev_suspend(struct pci_dev *pdev, pm_message_t state)
-{
- int i;
- struct platform_info *info = pci_get_drvdata(pdev);
- struct dev_info *hw_priv = &info->dev_info;
- struct ksz_hw *hw = &hw_priv->hw;
-
- /* Need to find a way to retrieve the device IP address. */
- static const u8 net_addr[] = { 192, 168, 1, 1 };
-
- for (i = 0; i < hw->dev_count; i++) {
- if (info->netdev[i]) {
- struct net_device *dev = info->netdev[i];
-
- if (netif_running(dev)) {
- netif_device_detach(dev);
- netdev_close(dev);
- }
- }
- }
- if (hw_priv->wol_enable) {
- hw_enable_wol(hw, hw_priv->wol_enable, net_addr);
- hw_cfg_wol_pme(hw, 1);
- }
-
- pci_save_state(pdev);
- pci_enable_wake(pdev, pci_choose_state(pdev, state), 1);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
- return 0;
-}
-#endif
-
-static char pcidev_name[] = "ksz884xp";
-
-static struct pci_device_id pcidev_table[] = {
- { PCI_VENDOR_ID_MICREL_KS, 0x8841,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { PCI_VENDOR_ID_MICREL_KS, 0x8842,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { 0 }
-};
-
-MODULE_DEVICE_TABLE(pci, pcidev_table);
-
-static struct pci_driver pci_device_driver = {
-#ifdef CONFIG_PM
- .suspend = pcidev_suspend,
- .resume = pcidev_resume,
-#endif
- .name = pcidev_name,
- .id_table = pcidev_table,
- .probe = pcidev_init,
- .remove = pcidev_exit
-};
-
-static int __init ksz884x_init_module(void)
-{
- return pci_register_driver(&pci_device_driver);
-}
-
-static void __exit ksz884x_cleanup_module(void)
-{
- pci_unregister_driver(&pci_device_driver);
-}
-
-module_init(ksz884x_init_module);
-module_exit(ksz884x_cleanup_module);
-
-MODULE_DESCRIPTION("KSZ8841/2 PCI network driver");
-MODULE_AUTHOR("Tristram Ha <Tristram.Ha@micrel.com>");
-MODULE_LICENSE("GPL");
-
-module_param_named(message, msg_enable, int, 0);
-MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
-
-module_param(macaddr, charp, 0);
-module_param(mac1addr, charp, 0);
-module_param(fast_aging, int, 0);
-module_param(multi_dev, int, 0);
-module_param(stp, int, 0);
-MODULE_PARM_DESC(macaddr, "MAC address");
-MODULE_PARM_DESC(mac1addr, "Second MAC address");
-MODULE_PARM_DESC(fast_aging, "Fast aging");
-MODULE_PARM_DESC(multi_dev, "Multiple device interfaces");
-MODULE_PARM_DESC(stp, "STP support");
projects / mirror_ubuntu-jammy-kernel.git / commitdiff