]> git.proxmox.com Git - mirror_ubuntu-disco-kernel.git/commitdiff
i2c: designware: 10-bit addressing mode enabling if I2C_DYNAMIC_TAR_UPDATE is set
authorChew, Chiau Ee <chiau.ee.chew@intel.com>
Thu, 26 Sep 2013 18:57:35 +0000 (02:57 +0800)
committerWolfram Sang <wsa@the-dreams.de>
Fri, 27 Sep 2013 16:12:31 +0000 (18:12 +0200)
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.

Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
drivers/i2c/busses/i2c-designware-core.c

index dbecf08399f86dd30baa7fa7b8964e2daf616bcb..5888feef1ac5a959b5f0471a3fb71b9a2b00bada 100644 (file)
@@ -98,6 +98,8 @@
 
 #define DW_IC_ERR_TX_ABRT      0x1
 
+#define DW_IC_TAR_10BITADDR_MASTER BIT(12)
+
 /*
  * status codes
  */
@@ -388,22 +390,34 @@ static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev)
 static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
 {
        struct i2c_msg *msgs = dev->msgs;
-       u32 ic_con;
+       u32 ic_con, ic_tar = 0;
 
        /* Disable the adapter */
        __i2c_dw_enable(dev, false);
 
-       /* set the slave (target) address */
-       dw_writel(dev, msgs[dev->msg_write_idx].addr, DW_IC_TAR);
-
        /* if the slave address is ten bit address, enable 10BITADDR */
        ic_con = dw_readl(dev, DW_IC_CON);
-       if (msgs[dev->msg_write_idx].flags & I2C_M_TEN)
+       if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) {
                ic_con |= DW_IC_CON_10BITADDR_MASTER;
-       else
+               /*
+                * If I2C_DYNAMIC_TAR_UPDATE is set, the 10-bit addressing
+                * mode has to be enabled via bit 12 of IC_TAR register.
+                * We set it always as I2C_DYNAMIC_TAR_UPDATE can't be
+                * detected from registers.
+                */
+               ic_tar = DW_IC_TAR_10BITADDR_MASTER;
+       } else {
                ic_con &= ~DW_IC_CON_10BITADDR_MASTER;
+       }
+
        dw_writel(dev, ic_con, DW_IC_CON);
 
+       /*
+        * Set the slave (target) address and enable 10-bit addressing mode
+        * if applicable.
+        */
+       dw_writel(dev, msgs[dev->msg_write_idx].addr | ic_tar, DW_IC_TAR);
+
        /* Enable the adapter */
        __i2c_dw_enable(dev, true);