Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.
v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
- rc = genphy_config_init(phydev);
- if (rc < 0)
- return rc;
-
rc = adin_config_rgmii_mode(phydev);
if (rc < 0)
return rc;
{
int ret;
- ret = genphy_config_init(phydev);
- if (ret < 0)
- return ret;
-
/* The RX and TX delay default is:
* after HW reset: RX delay enabled and TX delay disabled
* after SW reset: RX delay enabled, while TX delay retains the
static int dp83822_config_init(struct phy_device *phydev)
{
- int err;
int value;
- err = genphy_config_init(phydev);
- if (err < 0)
- return err;
-
value = DP83822_WOL_MAGIC_EN | DP83822_WOL_SECURE_ON | DP83822_WOL_EN;
return phy_write_mmd(phydev, DP83822_DEVADDR, MII_DP83822_WOL_CFG,
static int dp83848_config_init(struct phy_device *phydev)
{
- int err;
int val;
- err = genphy_config_init(phydev);
- if (err < 0)
- return err;
-
/* DP83620 always reports Auto Negotiation Ability on BMSR. Instead,
* we check initial value of BMCR Auto negotiation enable bit
*/
static struct phy_driver dp83848_driver[] = {
DP83848_PHY_DRIVER(TI_DP83848C_PHY_ID, "TI DP83848C 10/100 Mbps PHY",
- genphy_config_init),
+ NULL),
DP83848_PHY_DRIVER(NS_DP83848C_PHY_ID, "NS DP83848C 10/100 Mbps PHY",
- genphy_config_init),
+ NULL),
DP83848_PHY_DRIVER(TI_DP83620_PHY_ID, "TI DP83620 10/100 Mbps PHY",
dp83848_config_init),
DP83848_PHY_DRIVER(TLK10X_PHY_ID, "TI TLK10X 10/100 Mbps PHY",
- genphy_config_init),
+ NULL),
};
module_phy_driver(dp83848_driver);
{
int value, err;
- err = genphy_config_init(phydev);
- if (err < 0)
- return err;
-
value = phy_read(phydev, MII_DP83811_SGMII_CTRL);
if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
err = phy_write(phydev, MII_DP83811_SGMII_CTRL,
if (ret)
return ret;
- return genphy_config_init(phydev);
+ return 0;
}
/* This function is provided to cope with the possible failures of this phy
{
int val;
- genphy_config_init(phydev);
/*Zerodetect delay enable */
val = phy_read_mmd(phydev, MDIO_MMD_PCS,
PHY_ARDENNES_MMD_DEV_3_PHY_CFG);
.features = PHY_BASIC_T1_FEATURES,
- .config_init = genphy_config_init,
.config_aneg = genphy_config_aneg,
.ack_interrupt = lan87xx_phy_ack_interrupt,
return ret;
}
- return genphy_config_init(phydev);
+ return 0;
err:
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return rc;
}
- return genphy_config_init(phydev);
+ return 0;
}
static int vsc8584_did_interrupt(struct phy_device *phydev)
vsc73xx_config_init(phydev);
- return genphy_config_init(phydev);
+ return 0;
}
static int vsc739x_config_init(struct phy_device *phydev)
vsc73xx_config_init(phydev);
- return genphy_config_init(phydev);
+ return 0;
}
static int vsc73xx_config_aneg(struct phy_device *phydev)
if (ret < 0)
return ret;
- return genphy_config_init(phydev);
+ return 0;
}
static int vsc824x_ack_interrupt(struct phy_device *phydev)