#include <linux/types.h>
#include <linux/leds.h>
#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
-#include <asm/atmel-mci.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <linux/types.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
+#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/atmel-mci.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
#include <linux/spi/at73c213.h>
#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
#include <asm/setup.h>
-#include <asm/atmel-mci.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
#include <linux/spi/at73c213.h>
#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <asm/setup.h>
-#include <asm/atmel-mci.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
#include <video/atmel_lcdc.h>
#include <linux/fb.h>
-#include <asm/atmel-mci.h>
+#include <linux/atmel-mci.h>
#include <linux/io.h>
#include <asm/setup.h>
+++ /dev/null
-#ifndef __ASM_AVR32_ATMEL_MCI_H
-#define __ASM_AVR32_ATMEL_MCI_H
-
-#define ATMEL_MCI_MAX_NR_SLOTS 2
-
-struct dma_slave;
-
-/**
- * struct mci_slot_pdata - board-specific per-slot configuration
- * @bus_width: Number of data lines wired up the slot
- * @detect_pin: GPIO pin wired to the card detect switch
- * @wp_pin: GPIO pin wired to the write protect sensor
- *
- * If a given slot is not present on the board, @bus_width should be
- * set to 0. The other fields are ignored in this case.
- *
- * Any pins that aren't available should be set to a negative value.
- *
- * Note that support for multiple slots is experimental -- some cards
- * might get upset if we don't get the clock management exactly right.
- * But in most cases, it should work just fine.
- */
-struct mci_slot_pdata {
- unsigned int bus_width;
- int detect_pin;
- int wp_pin;
-};
-
-/**
- * struct mci_platform_data - board-specific MMC/SDcard configuration
- * @dma_slave: DMA slave interface to use in data transfers, or NULL.
- * @slot: Per-slot configuration data.
- */
-struct mci_platform_data {
- struct dma_slave *dma_slave;
- struct mci_slot_pdata slot[ATMEL_MCI_MAX_NR_SLOTS];
-};
-
-#endif /* __ASM_AVR32_ATMEL_MCI_H */
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
-#include <asm/atmel-mci.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/stat.h>
#include <linux/mmc/host.h>
+#include <linux/atmel-mci.h>
-#include <asm/atmel-mci.h>
#include <asm/io.h>
#include <asm/unaligned.h>
--- /dev/null
+#ifndef __LINUX_ATMEL_MCI_H
+#define __LINUX_ATMEL_MCI_H
+
+#define ATMEL_MCI_MAX_NR_SLOTS 2
+
+struct dma_slave;
+
+/**
+ * struct mci_slot_pdata - board-specific per-slot configuration
+ * @bus_width: Number of data lines wired up the slot
+ * @detect_pin: GPIO pin wired to the card detect switch
+ * @wp_pin: GPIO pin wired to the write protect sensor
+ *
+ * If a given slot is not present on the board, @bus_width should be
+ * set to 0. The other fields are ignored in this case.
+ *
+ * Any pins that aren't available should be set to a negative value.
+ *
+ * Note that support for multiple slots is experimental -- some cards
+ * might get upset if we don't get the clock management exactly right.
+ * But in most cases, it should work just fine.
+ */
+struct mci_slot_pdata {
+ unsigned int bus_width;
+ int detect_pin;
+ int wp_pin;
+};
+
+/**
+ * struct mci_platform_data - board-specific MMC/SDcard configuration
+ * @dma_slave: DMA slave interface to use in data transfers, or NULL.
+ * @slot: Per-slot configuration data.
+ */
+struct mci_platform_data {
+ struct dma_slave *dma_slave;
+ struct mci_slot_pdata slot[ATMEL_MCI_MAX_NR_SLOTS];
+};
+
+#endif /* __LINUX_ATMEL_MCI_H */